Enumerate the advantages and disadvantages of the four types of
roads:
-Earth Road
-Gravel Road
-Asphalt Road
-Concrete Road
It's important to note that the advantages and disadvantages mentioned above may vary depending on factors such as location, climate, traffic volume, and maintenance practices.
Advantages and disadvantages of the four types of roads are as follows:
1. Earth Road:
- Advantages:
- Low cost: Building an earth road is usually less expensive compared to other types of roads since it requires minimal construction materials.
- Accessibility: Earth roads can be constructed in remote areas where other types of roads may not be feasible due to their cost or geographical challenges.
- Eco-friendly: Earth roads have minimal environmental impact as they blend with the natural surroundings.
- Disadvantages:
- Vulnerable to weather conditions: Earth roads are highly susceptible to erosion caused by heavy rainfall, which can lead to road deterioration and washouts.
- Limited load-bearing capacity: Earth roads may not be able to support heavy traffic or loads due to their lower load-bearing capacity compared to other road types.
- Maintenance: Regular maintenance is required to fill potholes, control erosion, and ensure proper drainage.
2. Gravel Road:
- Advantages:
- Cost-effective: Gravel roads are relatively cheaper to build and maintain compared to asphalt or concrete roads.
- Good traction: The loose gravel surface provides better traction for vehicles, reducing the risk of skidding.
- Drainage: Gravel roads generally have good drainage capabilities, as water can seep through the loose material.
- Disadvantages:
- Dust and mud: Gravel roads can generate dust during dry weather and become muddy during rainfall, affecting visibility and making driving conditions challenging.
- Regular maintenance: Gravel roads require frequent grading and re-graveling to maintain their smoothness and prevent the formation of potholes.
- Limited lifespan: Gravel roads tend to deteriorate more quickly than asphalt or concrete roads, requiring more frequent repairs.
3. Asphalt Road:
- Advantages:
- Smooth and quiet: Asphalt roads offer a smooth and quiet driving experience due to their ability to absorb noise and vibrations.
- Durability: Properly constructed asphalt roads can have a long lifespan, requiring less frequent repairs compared to other road types.
- Safety: Asphalt provides good skid resistance, reducing the risk of accidents.
- Disadvantages:
- High initial cost: Asphalt roads can be expensive to construct initially due to the need for specialized equipment and materials.
- Heat sensitivity: Asphalt roads can soften and deform in extremely hot weather, leading to rutting and pothole formation.
- Environmental impact: The production of asphalt involves the extraction and processing of natural resources, which can have environmental consequences.
4. Concrete Road:
- Advantages:
- Longevity: Concrete roads have a long lifespan and require minimal maintenance compared to other road types.
- High load-bearing capacity: Concrete can withstand heavy traffic loads and is suitable for areas with high truck volumes.
- Reflectivity: Concrete roads have a higher reflectivity than other road types, enhancing visibility at night.
- Disadvantages:
- High initial cost: Concrete roads can be more expensive to construct initially compared to asphalt or gravel roads.
- Time-consuming construction: The construction process for concrete roads is generally more time-consuming due to curing requirements.
- Poor skid resistance: Concrete roads can be slippery, especially in wet conditions, requiring the use of additional surfacing treatments to improve skid resistance.
learn more about climate from given link
https://brainly.com/question/31944247
#SPJ11
A one meter drilled shaft is constructed in clay with a 2.0m.
base from the belled shaft.
a. Compute the capacity of the drilled shaft skin friction.
b. Compute the bearing capacity at the shaft base.
The capacity of the drilled shaft skin friction is to be calculated. The bearing capacity at the shaft base is to be computed.
To determine the capacity of the drilled shaft skin friction, we need to consider the properties of the clay and the length of the shaft. The skin friction capacity is influenced by factors such as the cohesion of the clay and the effective stress acting on the shaft surface. By using appropriate equations and considering the relevant parameters, engineers can calculate the skin friction capacity.
To compute the bearing capacity at the shaft base, we need to consider the properties of the clay and the dimensions of the base. The bearing capacity at the base depends on factors such as the undrained shear strength of the clay and the effective stress acting on the base. By applying relevant formulas and accounting for the appropriate parameters, engineers can determine the bearing capacity at the shaft base.
In both cases, it is important to consider the characteristics and behavior of the clay, as well as the effects of the shaft geometry and the surrounding soil conditions. Accurate calculations of the skin friction and bearing capacity are essential for ensuring the structural stability and performance of the drilled shaft.
Learn more about Drilled shafts
brainly.com/question/7220283
#SPJ11
Point M is the midpoint of line segment CD,
shown below.
What are the coordinates of point M?
C (6,10)
M
D (20, 18)
Answer:
M(13, 14)-------------------------
Each coordinate of the midpoint is the average of endpoints:
x = (6 + 20)/2 = 26/2 = 13y = (10 + 18)/2 = 28/2 = 14Therefore M is (13, 14).
Describe the engineering project providing, if available, the location, the purpose, the cost, the duration, etc.
Project: Construction of a Sustainable Bridge in Portland, Oregon
Location: Portland, Oregon, United States
Purpose: The project aims to replace an old and structurally deficient bridge with a modern, sustainable, and environmentally friendly one. The new bridge will accommodate increased traffic demands, provide improved safety features, and minimize its ecological footprint.
Cost: The estimated cost for the construction is $50 million, funded through a combination of federal grants and state funds.
Duration: The project is scheduled to be completed within three years, from groundbreaking to final inspection and opening for public use.
Details: The new bridge will incorporate sustainable design principles, using recycled materials and advanced engineering techniques to minimize energy consumption and carbon emissions. It will also include designated lanes for bicycles and pedestrians, promoting alternative transportation methods. The project will enhance connectivity, reduce traffic congestion, and contribute to the overall improvement of the city's infrastructure and environmental sustainability.
To know more about Sustainable, visit;
https://brainly.com/question/1581810
#SPJ11
A container encloses 31.1 g of CO2(g). The partial pressure of CO2 is 2.79 atm and the volume of the container is 31.3 L. What is theaverage, or root mean square, speed (in m/s) of the CO2 molecules in this container?
To calculate the average root mean square speed of CO2 molecules in a container, use the formula v(rms) = √(3RT/M), where R, T, and M are constants.
To find the average, or root mean square, speed of the CO2 molecules in the container, we can use the following formula:
v(rms) = √(3RT/M)
Where v(rms) is the root mean square speed, R is the gas constant (0.0821 L·atm/mol·K), T is the temperature in Kelvin, and M is the molar mass of CO2 (44.01 g/mol).
First, let's convert the given mass of CO2 to moles:
molar mass of CO2 = 44.01 g/mol
moles of CO2 = mass of CO2 / molar mass of CO2
= 31.1 g / 44.01 g/mol
Next, we need to convert the given volume of the container to liters:
volume = 31.3 L
Now, we can calculate the root mean square speed:
v(rms) = √(3RT/M)
= √(3 * 0.0821 L·atm/mol·K * T / 44.01 g/mol)
Since we don't have the temperature, we cannot calculate the root mean square speed accurately without that information.
To know more about average root mean square speed Visit:
https://brainly.com/question/30097486
#SPJ11
Mitch and Bill are both age 75. When Mitch was 22 years old, he began depositing $1200 per year into a savings account. He made deposits for the first 10 years, at which point he was forced to stop making deposits. However, he left his money in the account, where it continued to eam interest for the next 43 years Bil didn't start saving until he was 47 years old, but for the next 28 years he made annual deposits of $1200. Assume that both accounts earned an average annual retum of 5% (compounded once a year) Complete parts (a) through (d) below
a. How much money does Mitch have in his account at age 75?
At age 75, Mich has $
in his account.
b. How much money does Bill have in his account at age 75?
At age 75, Bill has 5 in his account.
c. Compare the amounts of money that Mitch and Bill deposit into their accounts.
Mitch deposits in his account and Bill deposits in his account.
d. Draw a conclusion about this parable. Choose the correct answer below
A. Both Bill and Mitch end with the same amount of money in their accounts, but Mitch had to deposit less money using his method. It is better to start saving as early as possible
B. Bill ends up with more money in his account than Mitch because he make more deposits than Mtch, and each additional deposit will accrue interest each year.
C. Mitch ends up with more money in his account despite not having deposited as much money as Bill because the interest that is initially accumulated accrues interest throughout the life of the account
D. Both Bill and Mitch have the same return on their investments despite using different methods of saving
a) Mitch has $65,055.97 in his account at age 75.
b) Bill has $89,901.98 in his account at age 75.
c) Mitch deposited $12,000 in his account, while Bill deposited $33,600 in his account.
d) Option (C) is correct.
Mitch ends up with more money in his account despite not having deposited as much money as
Bill because the interest that is initially accumulated accrues interest throughout the life of the account.
Therefore, it is better to start saving early.
a) We know that Mitch has been depositing $1200 per year for the first 10 years,
so he has deposited a total of $1200 * 10 = $12,000.
Now, this money has been in the account for the next 43 years.
Therefore, at the end of 43 years, the value of this money would have become:
$12,000 * (1 + 0.05) ^ 43 = $12,000 * 5.427164 = $65,055.97
Therefore, Mitch has $65,055.97 in his account at age 75.
b) Bill started depositing $1200 per year when he was 47 years old.
So, he has made annual deposits for the next 28 years.
Therefore, the total amount that Bill has deposited in his account would be:
$1200 * 28 = $33,600.
Now, this money has been in the account for the next 28 years.
Therefore, at the end of 28 years, the value of this money would have become:
$33,600 * (1 + 0.05) ^ 28 = $33,600 * 2.670824 = $89,901.98
Therefore, Bill has $89,901.98 in his account at age 75.
c) Mitch has deposited $12,000 in his account, while Bill has deposited $33,600 in his account.
d) Option (C) is correct. Mitch ends up with more money in his account despite not having deposited as much money as Bill because the interest that is initially accumulated accrues interest throughout the life of the account.
Therefore, it is better to start saving early.
To know more about interest visit:
https://brainly.com/question/3402162
#SPJ11
Find the local maxima, local minima, and saddle points, if any, for the function z = 3x3 – 36xy – 3y3. (Use symbolic notation and fractions where needed. Give your answer as point coordinates in t
Answer:
(0,0) is a saddle point
(-4,4) is a local maximum
Step-by-step explanation:
[tex]\displaystyle z=3x^3-36xy-3y^3\\\\\frac{\partial z}{\partial x}=9x^2-36y\\\\\frac{\partial z}{\partial y}=-36x-9y^2[/tex]
Determine critical points
[tex]9x^2-36y=0\\9x^2=36y\\\frac{x^2}{4}=y[/tex]
[tex]-36x-9y^2=0\\-36x-9(\frac{x^2}{4})^2=0\\-36x-\frac{9}{16}x^4=0\\x(-36-\frac{9}{16}x^3)=0\\\\x=0\\\\-36-\frac{9}{16}x^3=0\\-36=\frac{9}{16}x^3\\-64=x^3\\-4=x[/tex]
When x=0
[tex]9x^2-36y=0\\9(0)^2-36y=0\\-36y=0\\y=0[/tex]
When x=-4
[tex]9x^2-36y=0\\9(-4)^2-36y=0\\9(16)-36y=0\\144-36y=0\\144=36y\\4=y[/tex]
So, we need to check what kinds of points (0,0) and (-4,4) are.
For (0,0)
[tex]\displaystyle H=\biggr(\frac{\partial^2 z}{\partial x^2}\biggr)\biggr(\frac{\partial^2 z}{\partial y^2}\biggr)-\biggr(\frac{\partial^2 z}{\partial x\partial y}\biggr)^2\\\\H=(18x)(-18y)-(-36)^2\\\\H=(18(0))(-18(0))-(-36)^2\\\\H=-1296 < 0[/tex]
Therefore, (0,0) is a saddle point since [tex]H < 0[/tex].
For (-4,4)
[tex]\displaystyle H=\biggr(\frac{\partial^2 z}{\partial x^2}\biggr)\biggr(\frac{\partial^2 z}{\partial y^2}\biggr)-\biggr(\frac{\partial^2 z}{\partial x\partial y}\biggr)^2\\\\H=(18x)(-18y)-(-36)^2\\\\H=(18(-4))(-18(4))-(-36)^2\\\\H=(-72)(-72)-1296\\\\H=5184-1296\\\\H=3888 > 0[/tex]
Because [tex]H > 0[/tex] and since [tex]\frac{\partial^2z}{\partial x^2}=-72 < 0[/tex], then (-4,4) is a local maximum
Water flows along horizontal pipeline of 300 mm. The velocity at the throat (diameter 100 mm) is 10 m/s. If the coefficient of discharge, Cp=0.97, calculate the mercury manometer reading. (SG = 13.6). Air mengalir sepanjang saluran paip mendatar 300 mm. Halaju pada tekak (diameter 100mm) ialah 10 m/s. Jika pekali kadaralir, Cp= 0.97, kirakan bacaan manometer merkuri (SG = 13.6).
The mercury manometer reading is approximately 4.908 meters and
Pressure difference = 684240.14 N/m².
To calculate the mercury manometer reading, we can use the Bernoulli's equation, which relates the pressure, velocity, and elevation of a fluid in a flowing system.
Given:
Pipeline diameter (D₁) = 300 mm
= 0.3 m
Throat diameter (D₂) = 100 mm
= 0.1 m
Velocity at the throat (V₂) = 10 m/s
Coefficient of discharge (Cp) = 0.97
Specific gravity of mercury (SG) = 13.6
Step 1: Calculate the velocity at the pipeline entrance (V₁) using the continuity equation, which states that the mass flow rate is constant:
A₁V₁ = A₂V₂
A₁ = (π/4)D₁² (cross-sectional area at pipeline entrance)
A₂ = (π/4)D₂² (cross-sectional area at throat)
V₁ = (A₂/A₁) × V₂
V₁ = [(0.1)²/(0.3)²] × 10
V₁ = 1.11 m/s
Step 2: Calculate the pressure difference (ΔP) using Bernoulli's equation:
ΔP = (1/2)ρ(V₂² - V₁²) / Cp
where ρ is the density of water
ρ = SG × ρ_water
= 13.6 × 1000 kg/m³
(assuming [tex]\rho_{water}[/tex] = 1000 kg/m³)
ΔP = (1/2)(13.6 * 1000)(10² - 1.11²) / 0.97
= 684240.14 N/m²
Step 3: Convert pressure to mercury manometer reading:
Since the specific gravity (SG) of mercury is 13.6, the height of the mercury column (h) in the manometer can be calculated using the equation:
[tex]\Delta P=\rho_{mercury}\times g\times h[/tex]
[tex]$h=\frac{\Delta P}{(\rho_{mercury\times g})}[/tex]
where g is the acceleration due to gravity (9.81 m/s²) and [tex]\rho_{mercury[/tex] is the density of mercury.
[tex]\rho_{mercury[/tex] = SG × [tex]\rho_{water}[/tex]
= 13.6 * 1000 kg/m³
h = (684240.14) / (13.6 × 1000 * 9.81)
= 4.908 m
Therefore, the mercury manometer reading is approximately 4.908 meters.
Conclusion: Mercury manometer reading = 4.908 m
Pressure difference = 684240.14 N/m²
To know more about mercury manometer, visit
https://brainly.com/question/33710490
#SPJ11
A soil sample has a mass of 2290 gm and a volume of 1.15 x 10-3 m3, after drying, the mass of the sample 2035 gm, Gs for the soil is 268, Determine: 1. bulk density 2. water content 3. void ratio 4. Porosity 5. Degree of saturation
Degree of saturation is an important soil parameter that is used to determine other soil properties, such as hydraulic conductivity and shear strength.
Bulk density is the ratio of the mass of soil solids to the total volume of soil. Bulk density can be calculated using the following equation:
Bulk density = Mass of soil solids / Total volume of soil Bulk density can also be determined by using the following formula:
ρb = (M1-M2)/V
where ρb is the bulk density of the soil, M1 is the initial mass of the soil, M2 is the mass of the dry soil, and V is the total volume of the soil.
ρb = (2290 – 2035) / 1.15 x 10-3 ρb
= 22.09 kN/m3
Water content is the ratio of the mass of water to the mass of soil solids in the sample.
Water content can be determined using the following equation:
Water content = (Mass of water / Mass of soil solids) x 100%
Water content = [(2290 – 2035) / 2035] x 100%
Water content = 12.56%
Void ratio is the ratio of the volume of voids to the volume of solids in the sample. Void ratio can be determined using the following equation:
Void ratio = Volume of voids / Volume of solids
Void ratio = (Total volume of soil – Mass of soil solids) / Mass of soil solids
Void ratio = (1.15 x 10-3 – (2290 / 268)) / (2290 / 268)
Void ratio = 0.919
Porosity is the ratio of the volume of voids to the total volume of the sample.
Porosity can be determined using the following equation:
Porosity = Volume of voids / Total volume
Porosity = (Total volume of soil – Mass of soil solids) / Total volume
Porosity = (1.15 x 10-3 – (2290 / 268)) / 1.15 x 10-3
Porosity = 0.888
Degree of saturation is the ratio of the volume of water to the volume of voids in the sample.
Degree of saturation can be determined using the following equation:
Degree of saturation = Volume of water / Volume of voids
Degree of saturation = (Mass of water / Unit weight of water) / (Total volume of soil – Mass of soil solids)
Degree of saturation = [(2290 – 2035) / 9.81] / (1.15 x 10-3 – (2290 / 268))
Degree of saturation = 0.252.
In geotechnical engineering, the bulk density of a soil sample is the ratio of the mass of soil solids to the total volume of soil.
In other words, bulk density is the weight of soil solids per unit volume of soil.
It is typically measured in units of kN/m3 or Mg/m3. Bulk density is an important soil parameter that is used to calculate other soil properties, such as porosity and void ratio.
Water content is a measure of the amount of water in a soil sample. It is defined as the ratio of the mass of water to the mass of soil solids in the sample.
Water content is expressed as a percentage, and it is an important soil parameter that is used to determine other soil properties, such as hydraulic conductivity and shear strength.
Void ratio is the ratio of the volume of voids to the volume of solids in the sample.
Void ratio is an important soil parameter that is used to calculate other soil properties, such as porosity and hydraulic conductivity. It is typically measured as a dimensionless quantity.
Porosity is a measure of the amount of void space in a soil sample. It is defined as the ratio of the volume of voids to the total volume of the sample.
Porosity is an important soil parameter that is used to calculate other soil properties, such as hydraulic conductivity and shear strength.
Degree of saturation is a measure of the amount of water in a soil sample relative to the total volume of voids in the sample. It is defined as the ratio of the volume of water to the volume of voids in the sample.
Degree of saturation is an important soil parameter that is used to determine other soil properties, such as hydraulic conductivity and shear strength.
To know more about volume visit :
https://brainly.com/question/28058531
#SPJ11
Question 11 of 29
Which system of equations shown below could be used to solve the following
problem?
The product of x and y is equal to 24, and y is three times the value of x. What
is the value of x and y?
Answer: Could you add the picture?
Answer:
can you show an image?
Step-by-step explanation:
Using the function f(x) = -3/X
a.) Find the derivative of the function at x = 2. Use the definition of
derivative.
b.) Find the equation of the tangent line at x=2
Can I get an abstract (summary) for the following Organic
Chemistry: Amines and Amides Definition II. Amines and Amides Types
and Naming
Organic chemistry is a branch of chemistry that focuses on the study of the structure, properties, and reactions of organic compounds. Amines and amides are important classes of organic compounds that are widely used in various fields.Amines are organic compounds that contain one or more nitrogen atoms bonded to alkyl or aryl groups.
Amines are classified as primary, secondary, or tertiary based on the number of alkyl or aryl groups bonded to the nitrogen atom. The naming of amines depends on the number of alkyl or aryl groups bonded to the nitrogen atom.Amides are organic compounds that contain a carbonyl group (C=O) bonded to a nitrogen atom. Amides are classified as primary, secondary, or tertiary based on the number of alkyl or aryl groups bonded to the nitrogen atom. The naming of amides depends on the parent carboxylic acid and the substituent groups present on the nitrogen atom.In summary, amines and amides are two important classes of organic compounds.
Amines are classified as primary, secondary, or tertiary based on the number of alkyl or aryl groups bonded to the nitrogen atom, while amides are classified as primary, secondary, or tertiary based on the number of alkyl or aryl groups bonded to the nitrogen atom. The naming of amines and amides depends on the substituent groups present on the nitrogen atom.
To know more about Organic chemistry visit:-
https://brainly.com/question/14623424
#SPJ11
Calculation of the Specific Kinetic Energy for a Flowing Fluid Water is pumped from a storage tank through a tube of 3.00 cm inner diame- ter at the rate of 0.001 m/s. See Figure E21.2 What is the specific kinetic energy of the water in the tube? 3.00 cm ID 마 -0.001 m/s
Substituting the calculated velocity value into the formula will give us the specific kinetic energy of the water in the tube.
The specific kinetic energy of a flowing fluid can be calculated using the formula:
Specific kinetic energy = 1/2 * (velocity)^2
Given that the water is pumped through a tube with an inner diameter of 3.00 cm at a rate of 0.001 m/s, we can calculate the specific kinetic energy.
First, we need to find the velocity of the water. To do this, we can use the formula:
Velocity = Volume flow rate / Cross-sectional area
Since the water is pumped at a rate of 0.001 m/s and the inner diameter of the tube is 3.00 cm, we can calculate the cross-sectional area of the tube as follows:
Radius = (inner diameter / 2) = (3.00 cm / 2) = 1.50 cm = 0.015 m
Cross-sectional area = π * (radius)^2 = π * (0.015 m)^2
Now, we can substitute the values into the velocity formula:
Velocity = 0.001 m/s / (π * (0.015 m)^2)
Simplifying this expression gives us the value of the velocity.
Next, we can use the specific kinetic energy formula to calculate the specific kinetic energy:
Specific kinetic energy = 1/2 * (velocity)^2
Substituting the calculated velocity value into the formula will give us the specific kinetic energy of the water in the tube.
Remember to include the appropriate units in your final answer.
If you provide the values for the volume flow rate or any other relevant information, I can provide a more accurate calculation.
learn more about velocity on :
https://brainly.com/question/80295
#SPJ11
The specific kinetic energy of the water in the tube is 0.0000005 J.
The specific kinetic energy of a flowing fluid can be calculated using the equation:
Specific Kinetic Energy = (1/2) * (velocity)^2
In this case, the water is flowing through a tube with an inner diameter of 3.00 cm at a rate of 0.001 m/s.
To calculate the specific kinetic energy, we first need to convert the inner diameter of the tube to meters.
Inner diameter = 3.00 cm = 0.03 m
Next, we can calculate the velocity of the water flowing through the tube.
Velocity = 0.001 m/s
Now we can substitute the values into the equation:
Specific Kinetic Energy = (1/2) * (0.001 m/s)^2
Calculating the value:
Specific Kinetic Energy = (1/2) * (0.001 m/s)^2 = 0.0000005 J
Therefore, the specific kinetic energy of the water in the tube is 0.0000005 J.
Please note that the specific kinetic energy is the amount of kinetic energy per unit mass. It measures the energy of the fluid particles due to their motion.
Learn more about kinetic energy from this link
https://brainly.com/question/1135367
#SPJ11
What is the solubiliy of BaF2 in g/L? (Ksp=2.45x10^-5 M^3)
What is the solubility of {BaF}_{2} in {g} / {L} ? \left({K}_{{sp}}=2.45 x 10^{-5} {M}^{3}\right)
The solubility of BaF2 is 1.53 × 10-6 M or 2.68 × 10-4 g/L.
The question is about solubility, which means the maximum amount of solute that can be dissolved in a particular solvent. It is often expressed in grams of solute per liter of solvent.
Therefore, we can use the solubility product constant expression to solve the given question:
Ksp = [Ba2+][F-]^2Ksp
= solubility of BaF2 x 2[solubility of F-]
The molar mass of BaF2
= 137.33 + 18.99(2)
= 175.31 g/mol
Since 1 mol BaF2 produces 1 mol Ba2+ and 2 mol F-, we can write the following equations:
x mol BaF2 (s) ⇌ x mol Ba2+ (aq) + 2x mol F- (aq)
Ksp = [Ba2+][F-]^2
= 2.45 × 10-5 M3
= (x)(2x)2
= 4x3
Therefore:
4x3 = 2.45 × 10-5 M34x3
= 6.125 × 10-6 M3x3
= 6.125 × 10-6 M3 / 4x = 6.125 × 10-6 M3 / 4
= 1.53125 × 10-6 M
The solubility of BaF2 is 1.53125 × 10-6 M or 1.53125 × 10-6 mol/L.
To find the solubility in g/L, we can use the following formula:
mol/L × molar mass of BaF2
= g/L(1.53125 × 10-6 mol/L) × (175.31 g/mol)
= 2.68 × 10-4 g/L.
To know more about solubility visit:-
https://brainly.com/question/31493083
#SPJ11
need this before june 8th ill give 100 pts THIS IS URGENT SOMEONE PLEASE ANSWER THESE 5 QUESTIONS I NEED THEM EITHER TODAY OR TOMMOROW (BEFORE JUNE 8th or 9th)
Answer:
Step-by-step explanation:
#15) If the circles are identical then the diameters and radii are the same respectively
r = 4x > for circle 1
d = 2x +12 >diameter for 2nd circle. Change to radius by dividing by 2
r = (2x+12)/2
r = x + 6 >for circle 2
Make the r's equal
x+6 = 4x
6 = 3x
x = 2
#14) They want answer in C so just go from Kelvin to Celsius. Skip going to Farenheit.
K = C +273.15
3.5 = C +273.15
C = -269.65
#13)
1/7 A= 3
A = 21
1/8 B = 2
B= 16
no number)
10x + 5 + 5x - 1 = ____(2x + ____)
16x + 4
8 (2x +1/2)
Blank1: 8 Blank2: 1/2
#10)
2x +3x+4x =180
9x = 180
x= 20
2x = 40
3x = 60
4x = 80
wat diocument is the cost of the project normally specified? (10 points)
The cost of the project is normally specified in the project's budget document. This document provides an overview of the estimated costs for different project activities and serves as a financial guideline throughout the project's lifecycle.
The cost of a project refers to the total amount of money required to complete the project successfully. It includes various expenses such as materials, labor, equipment, overhead costs, and any other relevant expenditures.
To manage and track the project's finances effectively, a budget document is typically prepared. The budget document outlines the estimated costs for different project activities and provides a breakdown of expenses. It serves as a guideline for allocating funds and monitoring the project's financial performance.
The budget document includes specific cost categories, such as:
1. Direct costs: These are costs directly associated with the project, such as materials, equipment, and labor.
2. Indirect costs: These are costs that cannot be directly attributed to a specific project activity but are necessary for the overall project, such as administrative overhead or utilities.
3. Contingency costs: These are additional funds set aside to cover unexpected expenses or risks that may arise during the project.
4. Profit or margin: This represents the desired or expected profit or margin for the project, which is added to the total estimated costs.
By specifying the cost of the project in the budget document, project stakeholders can have a clear understanding of the financial requirements and make informed decisions regarding funding, resource allocation, and project feasibility.
Learn more about financial guideline visit:
https://brainly.com/question/31357451
#SPJ11
successful operation of materials in buildings requires an understanding of their characteristics as they affect the building at all stages of its lifetime. Identify the five (5) stages of life of a building / infrastructure.
The five stages of life of a building/infrastructure are pre-construction, construction, use, maintenance, and demolition.
A building/infrastructure undergoes various stages of life, from construction to demolition. Understanding these stages is vital for the successful operation of materials in buildings. The five stages of the life cycle of a building/infrastructure are as follows:
1.) Pre-construction Stage:
The pre-construction stage is the first stage, occurring before the building is constructed. It involves activities such as feasibility studies, conceptual design, site selection, and budgeting. This stage sets the foundation for the entire project.
2.) Construction Stage:
The construction stage is where the building is physically built. It encompasses activities such as site preparation, foundation laying, construction of the structural framework, installation of mechanical and electrical systems, and the finishing touches. This stage brings the design and plans to life.
3.) Use Stage:
The use stage is when the building is occupied and used for its intended purpose. It involves activities related to the operation and maintenance of the building, including regular upkeep, repairs, renovations, and periodic inspections. This stage focuses on ensuring the building functions optimally and meets the occupants' needs.
4.) Maintenance Stage:
The maintenance stage is crucial for preserving the building's condition and extending its lifespan. It includes routine maintenance tasks, preventive maintenance measures to prevent potential issues, and corrective maintenance to address any damages or malfunctions. This stage aims to keep the building in a safe and functional state.
5.) Demolition Stage:
The demolition stage marks the end of the building's life cycle. It involves activities such as conducting environmental assessments to handle hazardous materials appropriately, removing any hazardous substances, and the actual dismantling or demolition of the building. This stage clears the way for potential redevelopment or repurposing of the site.
Understanding these five stages of a building's life cycle is essential for comprehending the characteristics of materials and their effects on the building throughout its lifetime. Successful operation and management of materials in buildings require a comprehensive knowledge of these stages.
Learn more about building life cycle:
https://brainly.com/question/30476948
#SPJ11
Mention five waste products in Ghana that can be used for road
pavement construction. In which cities or towns can each of the
identified product be found in abundance? What are the potential
benefits
By utilizing waste products abundantly available in Ghana, the country can address waste management issues, create sustainable road infrastructure, and contribute to a circular economy.
In Ghana, there are several waste products that can be used for road construction due to their abundance. Some of these waste products include:
1. Plastic waste: Ghana generates a significant amount of plastic waste. This waste can be shredded and mixed with bitumen to create a durable and flexible material for road construction. This not only helps in reducing plastic waste but also improves road quality.
2. Used tires: The disposal of used tires is a major challenge in Ghana. However, they can be recycled and processed into rubberized asphalt, which provides enhanced durability and skid resistance for roads.
3. Construction and demolition waste: The construction industry generates a considerable amount of waste materials like concrete, bricks, and tiles. These materials can be crushed and used as aggregates for road base and sub-base layers, reducing the need for natural resources.
4. Agricultural waste: Ghana has abundant agricultural waste, such as rice husks, coconut fibers, and sawdust. These waste materials can be processed and used as additives in road construction to enhance stability and reduce material costs.
The potential benefits of using these waste products in road construction are twofold. Firstly, it helps in reducing the amount of waste that ends up in landfills, contributing to a cleaner and healthier environment. Secondly, it promotes resource efficiency by utilizing waste materials as substitutes for conventional road construction materials.
Learn more about abundance from the link given below:
https://brainly.com/question/1866454
#SPJ11
Non-porous Immobilized Enzyme Reaction (35 points): Substrate from bulk solution diffuses onto a porous pellet containing an enzyme to convert into a desired product. Some data is given below. Use that data to answer the questions and complete the Polymath code to produce a dimensionless concentration profile inside of the pellet. Data: Cs, bulk = 23 mmol/mL Km = 5 mmol/mL Total pellet radius = 0.60 mm Vmax = 0.078 mmol/(mL"sec) Diffusivity = 0.00010 mm2/sec a. Calculate and Thiele's Modulus, • (5 points) 3 b. Fill in the blanks in the POLYMATH code given in the next page. Some of the blanks will be filled with your results from Part A. Other blanks will be filled in based on what you 18 learned from type of POLYMATH code used to solve this kind of problem. (20 points). c. Run the POLYMATH code to solve for the value of the dimensionless concentration Xs that will exist at approximately the center of the pellet. This will require some trial and error on your part in running the code. (5 points) d. Draw the concentration profile that results from the correct POLYMATH code in the plot area on the next page. You are required to label your X axis and Y axis with numbers that fit the scale of the curve.
The Thiele's modulus (Φ) for the given non-porous immobilized enzyme reaction is 1.728.
Thiele's modulus is defined as the ratio of the reaction rate to the diffusion rate within the pellet.
Thiele's modulus (Φ) can be calculated using the formula:
Φ = (4/3) x (radius²) (Vmax / (D Km))
Given:
Total pellet radius (r) = 0.60 mm
Vmax = 0.078 mmol/(mL*sec)
Diffusivity (D) = 0.00010 mm²/sec
Km = 5 mmol/mL
Substituting the values into the formula, we have:
Φ = (4/3) * (0.60²) * (0.078 / (0.00010 * 5))
Φ = (4/3) * (0.36) * (0.078 / 0.00050)
Φ = 1.728
Therefore, the Thiele's modulus (Φ) for the given non-porous immobilized enzyme reaction is 1.728.
Learn more about modulus here:
https://brainly.com/question/30756002
#SPJ4
Cauchy's theorem is a big theorem which we will use often. Right away it reveals a number of interesting and useful properties of analytic functions. Find at least two practical applications of this theorem.
Cauchy's theorem is a fundamental result in complex analysis that has several practical applications.
Here are two examples:
1. Calculating contour integrals:
One practical application of Cauchy's theorem is in calculating contour integrals.
A contour integral is an integral along a closed curve in the complex plane.
Cauchy's theorem states that if a function is analytic within and on a closed curve, then the value of the contour integral of the function around that curve is zero.
This property allows us to simplify the calculation of certain integrals by considering paths that are easier to work with.
For example, if we have a complex function defined on a circle, we can use Cauchy's theorem to replace the circle with a simpler path, such as a line segment, and calculate the integral along that path instead.
2. Evaluating real integrals:
Another practical application of Cauchy's theorem is in evaluating real integrals.
By using a technique called the "keyhole contour," we can convert real integrals into contour integrals and apply Cauchy's theorem to simplify the calculation.
The keyhole contour involves choosing a closed curve that encloses the real line and includes a small circular arc around the singularity of the integrand, if there is one.
Then, by applying Cauchy's theorem, we can show that the contour integral along this keyhole contour is equal to the sum of the integrals along the real line and the circular arc.
This allows us to evaluate real integrals by calculating the contour integral, which can often be easier to handle due to the properties of analytic functions.
These are just two practical applications of Cauchy's theorem, but it is worth mentioning that this theorem has many other important applications in various branches of mathematics, such as complex analysis, potential theory, and physics.
Its versatility and usefulness make it a powerful tool for understanding and solving problems involving analytic functions.
Learn more about Cauchy's theorem from this link:
https://brainly.com/question/31058232
#SPJ11
A small square was cut off at the border of a large square sheet of paper. As a result, the perimeter of the sheet increased by 10% . By what percentage did the area of the sheet decrease.
Answer:
Step-by-step explanation:
Let the side of the original square, "square 1" be x.
Then the perimeter p = 4x
Let the side of the new square, "square 2" be y.
The perimeter of the leftover shape is
pₙ = x + x+ (x - y) + (x - y) = 4x - 2y
Given, the perimeter inc by 10%
[tex]p + p\frac{10}{100} = p_n[/tex]
[tex]4x + 4x\frac{10}{100} = 4x-2y\\\\4x\frac{10}{100} = -2y\\\\\implies \frac{4x}{-2} \frac{1}{10} = y\\\\\implies y = \frac{-x}{5}[/tex]
ar(leftover shape) = ar(square 3) + ar(rectangle 1) + ar(rectangle 2)
= (x - y)² + y(x - y) + y(x - y)
= x² + y² - 2xy + xy - y² + xy - y²
= x² - y²
sub y = -x/5,
ar(leftover shape) :
[tex]x^2 - \frac{(-x)^2}{5^2}\\ \\ =x^2- \frac{x^2}{25}\\\\=\frac{25x^2-x^2}{25} \\\\= \frac{24x^2}{25}[/tex]
[tex]ar(leftover\; shape) = \frac{24x^2}{25} \;(new \;area)[/tex]
ar(square 1) = x² (old area)
[tex]percentage \; increase = \frac{new - old}{old} * 100\%\\\\= \frac{\frac{24x^2}{25} - x^2}{x^2} * 100\%\\\\=[\frac{24}{25} -1 ]* 100\%\\\\=[\frac{24-25}{25}]* 100\%\\\\=[\frac{-1}{25}]* 100\%\\[/tex]
= -4%
The are has decreased by 4%
If the perimeter of a square sheet of paper increases by 10% after making a cut, the area of the sheet decreases by 21%.
Explanation:Let's assign a variable for this. We will assume the side length of the original square to be 'a' units. So, the perimeter of the original square would be 4a, and the area would be a². With a cut made, resulting in a 10% increase in the perimeter, the new perimeter becomes 1.1*4a = 4.4a. The side length of this new square is 4.4a/4 = 1.1a.
Now, the area of this new square can be calculated using the formula side^2, which gives us (1.1a)² = 1.21a². Thus, we can see that the area has decreased from a² to 1.21a². To calculate the percentage decrease in area, we use the formula [(original - new)/original]*100. This works out to be [(a² - 1.21a²)/a²]*100 = -21%.
So we can conclude that the area of the sheet decreases by 21% when a small square is cut off at the border causing the perimeter to increase by 10%.
Learn more about Percentage Change here:https://brainly.com/question/35855541
#SPJ2
To define an angle of 25 degrees in radians using Visual Python, it is needed to be written: Select one: 25/pi*180 O 25/pi/180 O 25pi/180 O 25*pi/180 O C
To define an angle of 25 degrees in radians using Visual Python, it should be written as 25*pi/180.
In Visual Python (VPython), angles are typically expressed in radians. Radians are the preferred unit of measurement for angles in mathematical calculations and most programming languages.
The conversion between degrees and radians involves multiplying the degree value by the conversion factor pi/180.
The constant pi represents the ratio of the circumference of a circle to its diameter and is approximately equal to 3.14159. Therefore, to convert 25 degrees to radians in Visual Python, we multiply 25 by pi/180, resulting in the expression 25*pi/180.
This calculation accurately represents the angle of 25 degrees in radians within the Visual Python environment.
To learn more about angle visit:
brainly.com/question/30147425
#SPJ11
1. Contractors should try not to do extra requested work without a change order signed by the Owner? A)True B)False
Contractors should try not to do extra requested work without a change order signed by the Owner. The answer to the question is (A) True.
Here's why: A change order is a formal document that outlines any changes to the original contract, such as additional work, modifications, or adjustments in scope, time, or cost. It serves as a legally binding agreement between the contractor and the owner. Without a change order, there is no clear agreement on the extra work being performed. This can lead to disputes regarding payment, delays, and even legal issues. By insisting on a change order, contractors ensure that any additional work is properly documented, including the agreed-upon compensation and any adjustments to the project schedule. Change orders protect both the contractor and the owner by establishing clear expectations and preventing misunderstandings.
In conclusion, contractors should not perform extra requested work without a change order signed by the Owner. This practice helps maintain transparency, avoid conflicts, and ensure fair compensation for additional services rendered.
Contractors : https://brainly.com/question/25795065
#SPJ11
The solid rod shown below has a diameter of 25 mm. Calculate the stresses that act at points A and B due to the loadings shown. σA=?MPa total normal stress at A 0/2 points τA= ? MPa total shear stress at A 14.0/2 points σB=?MPa total normal stress at B 15: 0/2 points τB=?MPa
We calculate the stresses at points A and B are as follows: σA = 20.4 MPa (total normal stress at A), τA = 40.8 MPa (total shear stress at A), σB = 40.8 MPa (total normal stress at B), τB = 0 MPa (total shear stress at B).
To calculate the stresses at points A and B, we need to consider the loading shown in the diagram. At point A, there is a compressive force applied vertically and a tensile force applied horizontally. At point B, there is only a compressive force applied vertically.
To calculate the stresses, we'll use the following formulas:
Normal stress (σ) = Force/Area
Shear stress (τ) = Force/Area
1. Calculate the stresses at point A:
- Total normal stress at A (σA):
- Vertical force = 10 kN (convert to N: 10,000 N)
- Area = π(radius)²
Area = π(0.025/2)²
Area = 0.0004909 m²
- σA = 10,000 N / 0.0004909 m²
σA = 20,400,417.4 Pa
σA = 20.4 MPa
- Total shear stress at A (τA):
- Horizontal force = 20 kN (convert to N: 20,000 N)
- Area = π(radius)²
Area = π(0.025/2)²
Area = 0.0004909 m²
- τA = 20,000 N / 0.0004909 m²
τA = 40,800,834.8 Pa
τA = 40.8 MPa
2. Calculate the stresses at point B:
- Total normal stress at B (σB):
- Vertical force = 20 kN (convert to N: 20,000 N)
- Area = π(radius)²
Area = π(0.025/2)²
Area = 0.0004909 m²
- σB = 20,000 N / 0.0004909 m²
σB = 40,800,834.8 Pa
σB = 40.8 MPa
- Total shear stress at B (τB):
- Since there is no horizontal force at point B, τB = 0 MPa
Therefore, the stresses at points A and B are as follows:
σA = 20.4 MPa (total normal stress at A)
τA = 40.8 MPa (total shear stress at A)
σB = 40.8 MPa (total normal stress at B)
τB = 0 MPa (total shear stress at B)
These calculations help us understand the stress distribution within the solid rod due to the given loadings.
Learn more about the stress from the given link-
https://brainly.com/question/29488474
#SPJ11
Draw the lewis structure of the polymer NEOPRENE also known as POLYCHLOROPRENE. Describe the shape and show 3 different bond angles from atoms in the molecule according to VSPER.
NEOPRENE also known as POLYCHLOROPRENE, has the chemical formula (C4H5Cl)n. It is a polymer that is widely used in the manufacturing of many industrial and consumer products. Its Lewis structure can be drawn by identifying the constituent atoms and their valence electrons.
Here is the Lewis structure of the polymer NEOPRENE: Shape of NEOPRENE: The shape of the NEOPRENE polymer is a three-dimensional structure. The molecule consists of a long chain of carbon atoms that are connected by single bonds. At each carbon atom, there is a group of atoms that includes a hydrogen atom, a chlorine atom, and a methyl group. The chlorine atoms are attached to the carbon atoms by single bonds, while the methyl groups are attached by double bonds. The shape of the NEOPRENE polymer is tetrahedral. It consists of four atoms that are arranged in a pyramid-like structure. Each carbon atom in the polymer has a tetrahedral geometry that is formed by the single bonds with the other carbon atoms in the chain, the hydrogen atoms, and the chlorine atoms. Three different bond angles from atoms in the molecule according to VSEPR theory: According to VSEPR theory, the bond angles in the NEOPRENE polymer can be predicted based on the number of electron groups around each carbon atom. There are four electron groups around each carbon atom in the polymer. Three of these groups are single bonds with other carbon atoms, hydrogen atoms, and chlorine atoms. The fourth group is a double bond with a methyl group. The bond angles between the single bonds are all 109.5 degrees, while the bond angle between the double bond and the single bond is 120 degrees.
In conclusion, the NEOPRENE polymer has a tetrahedral geometry and consists of carbon atoms that are connected by single bonds. The bond angles in the polymer are determined by VSEPR theory and are all 109.5 degrees except for the bond angle between the double bond and the single bond which is 120 degrees.
learn more about POLYCHLOROPRENE visit:
brainly.com/question/33169264
#SPJ11
10. 4.29 in/hr, and a drainage area of 11 hectares. Determine the mean runoff flow in cms with a runoff coefficient for a paved area, an intensity of
The mean runoff flow in cubic meters per second (cms) for a paved area with an intensity of 4.29 in/hr, a drainage area of 11 hectares, and a runoff coefficient of 0.9 is approximately 0.08917 cms.
To determine the mean runoff flow in cms (cubic meters per second), we need to consider the runoff coefficient, intensity, and the drainage area.
1. Calculate the total rainfall volume:
- Convert the intensity from in/hr to cm/hr:
- 1 inch = 2.54 cm
- 4.29 in/hr x 2.54 cm/in = 10.8996 cm/hr
- Multiply the intensity by the time period (usually in hours) to get the total rainfall volume:
- Assuming a time period of 1 hour, the total rainfall volume would be 10.8996 cm/hr x 1 hr = 10.8996 cm
2. Convert the drainage area from hectares to square meters:
- 1 hectare = 10,000 square meters
- 11 hectares x 10,000 sq m/hectare = 110,000 square meters
3. Calculate the mean runoff flow:
- Multiply the total rainfall volume by the runoff coefficient:
- Runoff coefficient for a paved area is typically between 0.8 and 0.95
- Assuming a runoff coefficient of 0.9, the mean runoff flow would be 10.8996 cm x 0.9 = 9.80964 cm
- Divide the result by the drainage area:
- 9.80964 cm / 110,000 sq m = 0.00008917 cm/s or 0.08917 cms
Therefore, the mean runoff flow in cubic meters per second (cms) for a paved area with an intensity of 4.29 in/hr, a drainage area of 11 hectares, and a runoff coefficient of 0.9 is approximately 0.08917 cms.
To learn more about mean
https://brainly.com/question/31101410
#SPJ11
The normal freezing point of acetic acid(CH3COOH) is 16.6 °C. If 17.24 grams of the nonvolatile nonelectrolyte 2,5-dimethylfuran(C6H8O), are dissolved in 167.6 grams of acetic acid, what is the freezing point of the resulting solution? Kfp for acetic acid is 3.90°C/m.
The freezing point of the resulting solution is approximately 12.4 °C.
To calculate the freezing point of the resulting solution, we need to apply the formula for freezing point depression:
ΔT = Kfp * molality
First, let's calculate the molality of the solution:
Molality (m) = moles of solute / mass of solvent (in kg)
Given:
Mass of 2,5-dimethylfuran (C6H8O) = 17.24 g
Mass of acetic acid (CH3COOH) = 167.6 g
We need to convert the masses to kg:
Mass of 2,5-dimethylfuran = 17.24 g = 0.01724 kg
Mass of acetic acid = 167.6 g = 0.1676 kg
Now, let's calculate the moles of 2,5-dimethylfuran:
Molar mass of 2,5-dimethylfuran (C6H8O) = 96.13 g/mol
Moles of 2,5-dimethylfuran = Mass / Molar mass
= 0.01724 kg / 96.13 g/mol
Next, calculate the molality:
Molality (m) = moles of solute / mass of solvent
= (moles of 2,5-dimethylfuran) / (mass of acetic acid in kg)
Now, substitute the given values into the formula:
ΔT = 3.90 °C/m * molality
Finally, calculate the freezing point of the solution:
Freezing point = Normal freezing point of acetic acid - ΔT
To know more about freezing point depression, visit:
https://brainly.com/question/32293855
#SPJ11
Complete a table, showing the powers of 3 modulo 31, until you reach 1 (because then it would repeat). (That is, you will have a table with entries k and 3k(mod31).)
Each entry should be between 1 and 30. Note: When computing 310 don't actually do 3 to the 10th power. Just multiply the result for 39 by 3 (then reduce if necessary).
Why does this confirm that 3 is a primitive root modulo 31?
Find the following orders, showing your work.
a.) ord7(5)
b.) ord37(7)
k | [tex]5^k[/tex] (mod 7) --|----------- 1 | 5 2 | 4 3 | 6 4 | 2 5 | 3 6 | 1
So, ord7(5) = 6.b.) ord37(7)
The table shows that the powers of 3 modulo 31 generates all the nonzero residues. It also has order 30, which is the largest possible order modulo 31. This shows that 3 is a primitive root modulo 31.Find the following orders, showing your work:
a.) ord7(5)To find the order of 5 modulo 7, we need to compute the powers of 5 until we get 1:
To find the order of 7 modulo 37, we need to compute the powers of 7 until we get 1: k | [tex]7^k[/tex] (mod 37) --|------------ 1 | 7 2 | 13 3 | 24 4 | 14 5 | 30 6 | 20 7 | 17 8 | 28 9 | 19 10 | 6 11 | 5 12 | 11 13 | 25 14 | 2 15 | 14 16 | 27 17 | 18 18 | 26 19 | 12 20 | 15 21 | 8 22 | 9 23 | 22 24 | 21 25 | 9 26 | 8 27 | 15 28 | 12 29 | 26 30 | 18 31 | 17 32 | 27 33 | 14 34 | 2 35 | 25 36 | 11
So, ord37(7) = 36.
To know more about tabulated visit :
https://brainly.com/question/27671097
#SPJ11
help with my question please
a) The median flow of water was the highest in November.
B) The range of the flow of water the highest in October.
C(i) 25% of the results in November show a flow of water greater than 23 m/s.
C(ii) Both the lower quartiles and medians were the same in the months of November and December.
How to evaluate and complete each of the statement?By critically observing the box plots, we can reasonably infer and logically deduce that the median flow of water was the highest in the month of November.
Part B.
In Mathematics and Statistics, the range of a data set can be calculated by using this mathematical expression;
Range = Highest number - Lowest number
Range Aug = 29 - 4 = 25
Range Sept = 32 - 5 = 27
Range Oct = 46 - 18 = 28 (highest)
Range Nov = 43 - 18 = 25
Range Dec = 32 - 15 = 17
Part C.
(i) In Mathematics and Statistics, the first quartile (Q₁) is referred to as 25th percentile (25%) and for the month of November it represents a flow rate of 23 m/s.
(ii) Both the lower quartiles and medians have the same flow rate of 23 m/s in the months of November and December.
Read more on range here: brainly.com/question/32352196
#SPJ1
A trapezoidal concrete lined canal is designed to convey water to a reclamation area of 120,000 feddans. The irrigation water requirement of the project is 25 m /feddan/day. The canal is constructed at a longitudinal slope of 0.0002 with a selected side slope of 2:1 (H:V), Calculate the required canal dimensions (bed width and water depth) under the following conditions: a) Best hydraulic section b) Bed Width is three times the water depth
According to the statement the water depth is 0.5155 m and the bed width is 3(0.5155) = 1.5465 m.
a) Best Hydraulic Section: To calculate the best hydraulic section of the canal, we use the trapezoidal section formula;
Q = (1/n)A(R²/3)S[tex]\frac{1}{2}[/tex]
where:
Q = Discharge in cubic meters per second
A = Cross-sectional area of the canal
R = Hydraulic radiusn = Coefficient of roughness of the canal bed
S = Longitudinal slope of the canal bed Given:
Length of the canal = 120,000 feddans
Irrigation water requirement = 25 m/feddan/day
Area to be irrigated = 120,000 × 4200 = 504,000,000 m²
Discharge of water to be carried = (25 × 504,000,000)/86400
= 145,833.33 m³/day
Slope of the canal bed = 0.0002
Side slope of the canal = 2:1 (H:V) = 2
Dimensions of the canal bed are bed width (b) and water depth (y).
Using the trapezoidal section formula;Q = (1/n)A(R²/3)S[tex]\frac{1}{2}[/tex]
Rearranging the formula to obtain A;A = (Qn/S[tex]\frac{1}{2}[/tex])(R[tex]\frac{2}{3}[/tex]))
The hydraulic radius is given as;R = A/P
where;
P = b + 2y(2) = (b + 2y)/2
Therefore;
P = b + y
Using the hydraulic radius in the area formula;A = R(P – b)²/4
The formula for the hydraulic radius is then simplified to;
R = y(1 + 4/y²)[tex]\frac{1}{2}[/tex]
Using the values of Q, S, n, and y in the formula for A;
A = 1.4845 y[tex]\frac{5}{3}[/tex] (b + y)[tex]\frac{2}{3}[/tex]
The canal bed width is three times the water depth;
b = 3y
Therefore;
A = 1.84 y[tex]\frac{8}{3}[/tex]
The area formula is then differentiated and equated to zero to find the minimum area;
dA/dy = (16.224/9) y[tex]\frac{5}{3}[/tex] = 0
Therefore;
y = 0.5558 m
A minimum depth of 0.5558 m or 55.58 cm is required.
Using the hydraulic radius formula;
R = y(1 + 4/y²)[tex]\frac{1}{2}[/tex]
Therefore;R
= 0.5506 m
The value of P can be calculated using the bed width formula;
P = b + 2y
The canal bed width is three times the water depth;
b = 3y
Therefore;
P = 9y
Using the value of P in the hydraulic radius formula;
R = A/P
Therefore;
A = PR²
= (0.5506 m)(9 × 0.5506^2) = 2.646 m²
The water depth is 0.5558 m and the bed width is 3(0.5558)
= 1.6674 m.
b) Bed Width is three times the Water Depth:
In this case, the bed width is three times the water depth.
Therefore;
b = 3yA = (1/n)(b + 2y) y R[tex]\frac{2}{3}[/tex] S[tex]\frac{1}{2}[/tex]
R = y(1 + 9)^(1/2)
Using the values of Q, S, n, and y in the formula for A;
A = 2.1986 y[tex]\frac{5}{3}[/tex]
The value of P can be calculated using the bed width formula;
P = b + 2y
The canal bed width is three times the water depth;
b = 3y
Therefore;
P = 9y
Using the value of P in the hydraulic radius formula;
R = A/P
Therefore;
R = 0.6172 m
The area formula is differentiated and equated to zero to obtain the minimum area;
dA/dy = (7.328/9) y[tex]\frac{2}{3}[/tex] = 0
Therefore;
y = 0.5155 m
A minimum depth of 0.5155 m or 51.55 cm is required.
Using the hydraulic radius formula;
R = y(1 + 9)[tex]\frac{1}{2}[/tex]
Therefore;
R = 1.732 y
Using the value of P in the hydraulic radius formula;
R = A/P
Therefore;
A = PR² = (0.5155 m)(9 × 1.732^2) = 8.4386 m²
The water depth is 0.5155 m and the bed width is 3(0.5155)
= 1.5465 m.
To know more about dimensions visit :
https://brainly.com/question/32471530
#SPJ11