2-1. a) The shear stress τ is constant across the flow. b) The velocity is maximum at the center (r = 0) and decreases linearly as the radial distance increases. c)v_max = (P₁ - P₂) / (4μL) * [tex]R^{2}[/tex] and v_avg = (1 / (π([tex]R^{2} -a^{2}[/tex]))) * ∫[a to R] v * 2πr dr 2-2.a) The shear stress is constant for parallel plates. b) The velocity profile shows that the velocity is maximum at the centerline and decreases parabolically .c)v_max = (P₁ - P₂) / (2μh) and v_avg = (1 / (2h)) * ∫[-h to h] v dr.
2-1. Flow in an annular region between concentric cylinders:
(a) Shear stress profile:
In an incompressible fluid flow between concentric cylinders, the shear stress τ varies with radial distance r. The shear stress profile can be obtained using the Navier-Stokes equation:
τ = μ(dv/dr)
where τ is the shear stress, μ is the dynamic viscosity, v is the velocity of the fluid, and r is the radial distance.
Since the flow is at steady state, the velocity profile is independent of time. Therefore, dv/dr = 0, and the shear stress τ is constant across the flow.
(b) Velocity profile:
To determine the velocity profile in the annular region, we can use the Hagen-Poiseuille equation for flow between concentric cylinders:
v = (P₁ - P₂) / (4μL) * ([tex]R^{2} -r^{2}[/tex])
where v is the velocity of the fluid, P₁ and P₂ are the pressures at the outer and inner cylinders respectively, μ is the dynamic viscosity, L is the length of the cylinders, R is the outer radius, and r is the radial distance.
The velocity profile shows that the velocity is maximum at the center (r = 0) and decreases linearly as the radial distance increases, reaching zero at the outer cylinder (r = R).
(c) Maximum and average velocities:
The maximum velocity occurs at the center (r = 0) and is given by:
v_max = (P₁ - P₂) / (4μL) * [tex]R^{2}[/tex]
The average velocity can be obtained by integrating the velocity profile and dividing by the cross-sectional area:
v_avg = (1 / (π([tex]R^{2} -a^{2}[/tex]))) * ∫[a to R] v * 2πr dr
where a is the inner radius of the annular region.
2-2. The flow between parallel plates:
(a) Shear stress profile:
For flow between very wide or broad parallel plates, the shear stress profile can be obtained using the Navier-Stokes equation as mentioned in problem 2-1. The shear stress τ is constant across the flow.
(b) Velocity profile:
The velocity profile for flow between parallel plates can be obtained using the Hagen-Poiseuille equation, modified for this geometry:
v = (P₁ - P₂) / (2μh) * (1 - ([tex]r^{2} /h^{2}[/tex]))
where v is the velocity of the fluid, P₁ and P₂ are the pressures at the top and bottom plates respectively, μ is the dynamic viscosity, h is the distance between the plates, and r is the radial distance from the centerline.
The velocity profile shows that the velocity is maximum at the centerline (r = 0) and decreases parabolically as the radial distance increases, reaching zero at the plates (r = ±h).
(c) Maximum and average velocities:
The maximum velocity occurs at the centerline (r = 0) and is given by:
v_max = (P₁ - P₂) / (2μh)
The average velocity can be obtained by integrating the velocity profile and dividing by the distance between the plates:
v_avg = (1 / (2h)) * ∫[-h to h] v dr
These formulas can be used to calculate the shear stress profile, velocity profile, and maximum/average velocities for the given geometries.
Learn more about shear stress;
https://brainly.com/question/30407832
#SPJ4
The value of the bulk specific gravity of the aggregates is:
A. 2.74
B. 2.59
C. 2.67
D. 2.63
E. None of the options are correct
The Bulk Specific Gravity (BSG) of the aggregates mentioned in the question is 2.63.
Here's the explanation:
In civil engineering, bulk specific gravity (BSG) is a critical engineering property that determines the density of both coarse and fine aggregates used in construction work.
The bulk specific gravity of a material is the ratio of its weight to the volume of the material, including all pores within it.
The bulk specific gravity of aggregates is an essential physical property that is used to determine the yield of concrete per unit volume.
The higher the BSG value of the aggregates, the less air or water it will displace and the greater the density of the material.
The Bulk Specific Gravity (BSG) of the aggregates mentioned in the question is 2.63.
To know more about Specific Gravity, visit:
https://brainly.com/question/31778988
#SPJ11
The change in concentration of N2O5 in the reaction 2N2O5 (g) → 4NO2 (g) + O2 (g) is shown below: Time (s) concentration of N2O5 (M) 0 0.020 1.00 x 102 0.017 2.00 x 102 0.014 3.00 x 102 0.014 4.00 x 102 0.010 5.00 x 102 0.009 6.00 x 102 0.007 7.00 x 102 0.006 Calculate the rate of decomposition of N2O5 between 100 - 300 s. what is the rate of reaction between the same time (100 - 300 s)?
The rate of decomposition of N2O5 between 100 - 300 s is -1.5 x 10⁻⁵ M/s, and the rate of reaction within the same time is -7.5 x 10⁻⁶ M/s.
To calculate the rate of decomposition of N2O5 between 100 - 300 s, we need to determine the change in concentration of N2O5 and divide it by the corresponding time interval.
Change in concentration of N2O5 = [N2O5]final - [N2O5]initial
= 0.014 M - 0.017 M
= -0.003 M
Time interval = 300 - 100
= 200 s
Rate of decomposition of N2O5 = (Change in concentration of N2O5) / (Time interval)
= (-0.003 ) / (200 )
= -1.5 x 10 M/s
The rate of reaction between the same time interval (100 - 300 s) can be determined by dividing the rate of decomposition by the stoichiometric coefficient of N2O5 in the balanced equation. In this case, the coefficient is 2.
Rate of reaction = Rate of decomposition of N2O5 / 2
= (-1.5 x 10 ) / 2
= -7.5 x 10⁻⁶ M/s
Therefore, the rate of reaction between 100 - 300 s is -7.5 x 10⁻⁶ M/s.
To know more about rate of decomposition and reaction, visit:
https://brainly.com/question/32682253
#SPJ11
Choose the correct answer 1- The principle parties of construction project are: a) Client, designer, contractor. b) owner, client, contractor. c) owner, designer, client d) b or c. 2- construction can be defined as: a) The act of constructing. b) The result of constructing. c) The process, art, or manner of constructing something. d) All the above. 3- Construction process can be defined as: a) The process, art, or manner of constructing something. b) The process or step in which the plans, specifications, materials, permanent equipment are transformed by a contractor into a finished facility. c) The event in which the plans, specifications, materials, permanent equipment are transformed by a contractor into a finished facility. d) All the above. 4- Electric power construction projects, highways, utilities and petrochemicals plants are examples of...... a) Building construction projects. b) Heavy engineering construction projects. c) Manufacturing projects. d) Nothing from the above. 5- Equipment cost comes.......... .labor in terms of its effect on the outcome of a particular project. a) After. b) Before. c) With. d) Nothing from the above
A comprehensive understanding of the principle parties in a construction project, the definition of construction, the construction process, examples of construction projects, and the relationship between equipment cost and labor.
1- The correct answer is a) Client, designer, contractor. The principle parties of a construction project include the client, who is the person or organization that initiates the project and funds it, the designer who creates the plans and specifications for the project, and the contractor who is responsible for the physical construction of the project.
2- The correct answer is d) All the above. Construction can be defined as the act of constructing, the result of constructing, and the process, art, or manner of constructing something. All these definitions encompass different aspects of the construction process.
3- The correct answer is d) All the above. The construction process can be defined as the process, art, or manner of constructing something, as well as the process or step in which the plans, specifications, materials, and permanent equipment are transformed by a contractor into a finished facility. It is also the event in which these elements are transformed. All these definitions capture different perspectives of the construction process.
4- The correct answer is b) Heavy engineering construction projects. Electric power construction projects, highways, utilities, and petrochemical plants are examples of heavy engineering construction projects. These projects involve complex engineering and infrastructure development.
5- The correct answer is c) With. Equipment cost comes with labor in terms of its effect on the outcome of a particular project. Equipment and labor are both important factors in construction projects, and their costs are interconnected and impact the final outcome.
These answers provide a comprehensive understanding of the principle parties in a construction project, the definition of construction, the construction process, examples of construction projects, and the relationship between equipment cost and labor.
Learn more about construction from this link:
https://brainly.com/question/28532898
#SPJ11
A simply supported beam has a cross section of 350mm x 700mm. It carries a bending moment of 35kNm. If the modulus of rupture fr = 3.7MPa, determine whether the beam reached its cracking stage. Explain your answer briefly.
Based on the given information, the simply supported beam with a cross section of 350mm x 700mm carrying a bending moment of 35kNm has reached its cracking stage.
To determine whether the beam has reached its cracking stage, we need to compare the maximum bending stress in the beam with the modulus of rupture (fr). The maximum bending stress (σ) can be calculated using the formula:
σ = (M × y) / (I × c)
Where:
M = Bending moment = 35kNm
y = Distance from the neutral axis to the extreme fiber (half of the beam's depth) = 350mm / 2 = 175mm = 0.175m
I = Moment of inertia of the cross-section = (b × [tex]h^3[/tex]) / 12, where b is the beam width and h is the beam height
c = Distance from the neutral axis to the extreme fibre (half of the beam's width) = 700mm / 2 = 350mm = 0.35m
Substituting the values into the equation, we can calculate the maximum bending stress (σ). If the calculated bending stress is greater than the modulus of rupture (fr), then the beam has reached its cracking stage.
However, since the dimensions of the beam are given in millimeters and the modulus of rupture (fr) is given in megapascals (MPa), we need to convert the dimensions to meters:
b = 350mm = 0.35m
h = 700mm = 0.7m
After substituting all the values, we find that the maximum bending stress is:
σ = (35kNm × 0.175m) / ((0.35m × 0.7[tex]m^3[/tex]) / 12) = 8.228MPa
Since the calculated bending stress (8.228MPa) is greater than the modulus of rupture (3.7MPa), we can conclude that the beam has reached its cracking stage.
To learn more about bending moment refer:
https://brainly.com/question/13798847
#SPJ11
Helppp pls
Question 55-ICA1
From a class containing 12 girls and 10 boys, three students are to be selected to serve on a school advisory panel. Here are five different methods of making the selection.
Which is the best sampling method, if you want the school panel to represent a fair and
representative view of the opinions of your class?
A) Select the first three names on the class attendance list.
B) Select the first three students who volunteer.
C)Place the names of the 22 students in a hat, mix them thoroughly, and select three
names from the mix.
D)Select the first three students who show up for class tomorrow.
Select the last ten names from the class attendance list. Place their names in a hat,
mix them thoroughly, and select three names from the mix.
Reason:
This method ensures that every student has an equal chance of being selected. This assumes the names are put back into the hat (i.e. replacement is done). Any repeat selections are ignored.
Choices A, B, D, and E all represent situations where bias is introduced. For instance, choice E places bias toward the last ten people on the list, while ignoring the other people. The goal of selecting a sample is to eliminate as much bias as possible.
Design a physical security solution for a university premise to include
a. Define a safety program for the university comprising at least 4 components
b. Identify a security system that issues warnings for 3 different threats
c. Design a warning system for each threat from (b)
d. Identify the technology constraints for implementing the warning system from (c)
e. Propose a training program for staff to reduce the risk from the threats listed in (b)
A university's physical security program should include fire safety measures, emergency response measures, access controls, and procedures for dealing with hazardous materials and waste. Three types of threats must be addressed: intrusion detection alarms, CCTV cameras, and fire alarms. Warning systems can be developed for each threat, with technology constraints affecting resource availability, compatibility, and installation costs. Staff training is essential to reduce risk and ensure a secure environment.
A university's physical security solution should include fire safety measures, emergency response measures, access controls, and procedures for dealing with hazardous materials and waste. Three types of threats must be addressed to secure the premise: intrusion detection alarms, CCTV cameras, and fire alarms.
Warning systems can include audible alarms, automatic email or text message alerts, and automatic notifications to the fire department. Technology constraints for implementing warning systems include resource availability, compatibility, and installation costs. A training program for staff should include recognizing suspicious activities, responding appropriately, proper use of access control systems, fire safety equipment, and emergency response protocols. By addressing these threats, a university can create a secure and safe environment for its students and staff.
To know more about physical security program Visit:
https://brainly.com/question/32647652
#SPJ11
8. An atom with a mass number of 80 and with 35 ncutrons will have a) 16 protons b) c) d) c) 35 protons 45 protons 80 protons 115 protons 9. Isotopes are atoms with a) a different number of protons and neutrons b) the same number of protons and neutrons c) the same number of protons and electrons b)
An atom with a mass number of 80 and 35 neutrons will have 45 protons, and isotopes are atoms with a different number of protons and neutrons.
An atom with a mass number of 80 and with 35 neutrons will have: c) 45 protons.
The number of protons in an atom is determined by its atomic number, which is the same for all atoms of a particular element. Since the number of neutrons is given as 35, we can subtract this from the mass number (80) to find the number of protons: 80 - 35 = 45.
Isotopes are atoms with: a) a different number of protons and neutrons.
Isotopes are variants of an element that have the same number of protons (same atomic number) but different numbers of neutrons (different mass numbers). This difference in the number of neutrons leads to variations in the atomic mass of the isotopes.
To know more about isotopes,
https://brainly.com/question/12767403
#SPJ11
Find a) any critical values and by any relative extrema. g(x)= x^3- 3x+8
For the function g(x) = x^3 - 3x + 8, the critical values are x = -1 and x = 1.
The function g(x) = x^3 - 3x + 8 is a cubic polynomial.
To find the critical values and any relative extrema, we can follow these steps:
1. Find the derivative of g(x) by using the power rule. The derivative of x^n is nx^(n-1).
g'(x) = 3x^2 - 3
2. Set the derivative equal to zero and solve for x to find the critical values.
3x^2 - 3 = 0
To solve this equation, we can factor out a 3:
3(x^2 - 1) = 0
Now, set each factor equal to zero:
x^2 - 1 = 0
Solving for x, we get:
x^2 = 1
x = ±1
Therefore, the critical values of g(x) are x = -1 and x = 1.
3. To determine whether the critical values correspond to relative extrema, we need to analyze the concavity of the graph.
We can find the second derivative by taking the derivative of g'(x):
g''(x) = 6x
4. Now, substitute the critical values into the second derivative equation to determine the concavity at each point.
For x = -1:
g''(-1) = 6(-1) = -6
For x = 1:
g''(1) = 6(1) = 6
The negative second derivative at x = -1 indicates that the graph is concave down, while the positive second derivative at x = 1 indicates that the graph is concave up.
5. Using the information about concavity, we can determine the nature of the relative extrema.
At x = -1, the graph changes from increasing to decreasing, so there is a relative maximum at this point.
At x = 1, the graph changes from decreasing to increasing, so there is a relative minimum at this point.
In summary, for the function g(x) = x^3 - 3x + 8, the critical values are x = -1 and x = 1. At x = -1, there is a relative maximum, and at x = 1, there is a relative minimum.
Learn more about relative extrema:
brainly.com/question/1938915
#SPJ11
find 95% reliability on 1.000.000 people when conducting a sample
or trend
assignment
Keep in mind that the estimated proportion, p, can affect the sample size significantly.
If you can provide an estimated proportion or an assumed value for p, I can calculate the sample size for you.
To determine the required sample size for a given population with a desired level of reliability, we need to consider the margin of error and confidence level.
The margin of error defines the maximum allowable difference between the sample estimate and the true population parameter, while the confidence level indicates the level of certainty we want to have in our results.
Since you mentioned a 95% reliability, we can assume a 95% confidence level, which is a common choice. The standard margin of error associated with a 95% confidence level is approximately ±1.96 (assuming a normal distribution).
However, it's important to note that the margin of error can be adjusted based on the specific characteristics of the population being studied.
To calculate the required sample size, we also need to know the estimated proportion of the population exhibiting the trend or characteristic of interest.
Without this information, we can't provide an exact sample size. However, I can show you a general formula for calculating the sample size based on an estimated proportion.
The formula to determine the sample size is:
n = (Z^2 * p * (1 - p)) / E^2
Where:
n = required sample size
Z = Z-score corresponding to the desired confidence level (95% is approximately 1.96)
p = estimated proportion of the population exhibiting the trend or characteristic
E = margin of error
To know more about equation click-
http://brainly.com/question/2972832
#SPJ11
1.What is the major side product of this reaction? 2. Why is an excess of ethyl bromide used in this reaction? 3. What is the function of the potassium hydroxide in the first step of the reaction? 4. Would sodium hydroxide work as well as potassium hydroxide in this reaction? 5. Why is it important to be sure all of the phenol and base are in solution before mixing them? 6. During the course of the reaction, a white precipitate forms. What is this material? 7. Both the phenol and ethyl alcohol contain OH groups, but only the phenolic OH group reacts to any extent. Why? 8. If you wanted to adapt this procedure to prepare the analogous propoxy compound, how much propyl iodide would you have to use to carry out the reaction on the same scale?
1. The major side product of this reaction is ethyl phenyl ether. This is formed when the ethoxide ion reacts with the ethyl bromide, resulting in the formation of a new carbon-oxygen bond.
2. An excess of ethyl bromide is used in this reaction to ensure that the reaction goes to completion. By having an excess of one reactant (ethyl bromide), it helps to drive the reaction forward, as it increases the chances of ethyl bromide molecules colliding with the phenoxide ions and undergoing the desired reaction.
3. The function of potassium hydroxide (KOH) in the first step of the reaction is to deprotonate the phenol. KOH is a strong base that readily accepts a proton (H+), converting phenol (which has a slightly acidic hydrogen) into phenoxide ion. This deprotonation is important for the subsequent reaction with ethyl bromide to form ethyl phenyl ether.
4. Sodium hydroxide (NaOH) would work similarly to potassium hydroxide in this reaction. Both are strong bases and can deprotonate phenol to form phenoxide ion. However, the choice between the two depends on factors such as availability, cost, and specific reaction conditions.
5. It is important to ensure that all of the phenol and base are in solution before mixing them because the reaction between the phenoxide ion and ethyl bromide occurs in solution. If any of the reactants are not in solution, the chances of successful collisions and reaction between the reactants will be reduced.
6. The white precipitate that forms during the course of the reaction is potassium bromide (KBr). This is a result of the reaction between potassium hydroxide and ethyl bromide, which produces potassium bromide as a byproduct. It appears as a white solid that separates from the reaction mixture.
7. The phenolic OH group reacts more readily compared to the OH group in ethyl alcohol because the phenolic OH group is more acidic. It is more likely to lose a proton and form the phenoxide ion, which can then react with ethyl bromide. On the other hand, the OH group in ethyl alcohol is less acidic and is less likely to undergo deprotonation and subsequent reaction.
8. To adapt this procedure to prepare the analogous propoxy compound, the same scale of reaction can be maintained. The molar ratio between the phenol and the propyl iodide is 1:1. Therefore, the amount of propyl iodide needed would be equal to the amount of phenol used in the reaction. If the same amount of phenol is used as before, then the same amount of propyl iodide would be required for the reaction.
In summary, the major side product is ethyl phenyl ether, an excess of ethyl bromide is used to drive the reaction, potassium hydroxide deprotonates phenol, sodium hydroxide can be used instead of potassium hydroxide, ensuring all reactants are in solution enhances reaction chances, the white precipitate is potassium bromide, the phenolic OH group is more acidic and reacts readily, and the amount of propyl iodide required for the analogous reaction is equal to the amount of phenol used.
Learn more about reaction:
brainly.com/question/30464598
#SPJ11
there is an experiment done using the Basic hydrology system to do the investigation of rainfall and runoff and also flow from the well.
From the experiment we find Piezometer Position, Radius from well (mm), and Head (mm).
The experiment using the Basic Hydrology system provides valuable insights into the relationship between rainfall, runoff, and the flow of groundwater from a well. By analyzing the data on Piezometer Position, Radius from well, and Head, we can better understand the hydrological dynamics of the area under investigation.
To analyze the experiment's findings, we can follow these steps:
1. Understand the variables:
- Piezometer Position: This refers to the location of the piezometer, which measures the pressure of groundwater.
- Radius from well: This is the distance between the well and the piezometer, measured in millimeters (mm).
- Head: The head represents the height of the water level in the piezometer, also measured in millimeters (mm). It indicates the pressure of the groundwater.
2. Analyze the relationship between variables:
- By examining the Piezometer Position and Radius from well, we can understand the spatial distribution of the piezometers around the well. This information helps us determine how the pressure of groundwater varies with distance from the well.
- The Head measurements provide insights into the pressure of groundwater at different points around the well. Comparing the heads at different piezometer positions helps identify areas of higher or lower groundwater pressure.
3. Interpret the data:
- Based on the findings, we can draw conclusions about the flow of groundwater and the effects of rainfall and runoff on the hydrological system. For example, if there is a high head in a particular piezometer position after heavy rainfall, it suggests that water is flowing into the well from that direction.
4. Use examples to support your interpretation:
- Suppose the experiment shows a piezometer positioned close to the well with a large radius and a high head. This indicates that the pressure of groundwater is high near the well due to the proximity and the large area of influence. Conversely, a piezometer positioned farther away with a small radius and a low head suggests lower groundwater pressure in that location.
learn more about Hydrology :
https://brainly.com/question/22961347
#SPJ11
Derivative PFR reactor step by step to find volume from mass balance with necessary assumptions
A derivative PFR reactor can be used to find the volume from mass balance. This type of reactor is also known as a continuous flow stirred tank reactor (CSTR).
The volume of this reactor is determined by the mass balance equation. Assumptions: First, it is assumed that the system is a steady-state, so the mass flow rate of the reactants is constant. Second, it is assumed that the reactor is well-mixed and that the concentration is the same throughout the reactor. Third, it is assumed that the reaction is first-order. Fourth, it is assumed that the rate of the reaction is constant.
Step-by-step guide:
1. Write down the mass balance equation.
2. Use the rate law to express the rate of reaction.
3. Substitute the rate of reaction into the mass balance equation.
4. Solve the differential equation for the concentration as a function of position.
5. Integrate the differential equation to obtain the exit concentration.
6. Calculate the volume of the reactor using the mass balance equation and the exit concentration.
Learn more about stirred tank reactor visit:
brainly.com/question/33192126
#SPJ11
The middle of the 5 m simple beam has a dimension of 350 mm by 1000 mm. On that location, the beam is reinforced with 3-Ø28mm on the top and 5-Ø32 mm at the bottom. The concrete cover to be used is 40 mm. The concrete strength of the beam is 27.6 MPa. The reinforcement (both tension and compression) used is Grade 50 (fy = 345 MPa). If the beam is carrying a total dead load of 50 kN/m all throughout the span, a. Determine the depth of the compression block.
The depth of the compression block can be determined using the formula:
d = (A - As) / b
Where:
d = depth of the compression block
A = area of the concrete section
As = area of steel reinforcement
b = width of the compression block
First, let's calculate the area of the concrete section:
A = width * depth
A = 1000 mm * (350 mm - 40 mm)
A = 1000 mm * 310 mm
A = 310,000 mm^2
Next, let's calculate the area of steel reinforcement at the top:
Ast = number of bars * area of each bar
Ast = 3 * (π * (28 mm / 2)^2)
Ast = 3 * (π * 14^2)
Ast = 3 * (π * 196)
Ast = 3 * 615.75
Ast = 1,847.25 mm^2
Similarly, let's calculate the area of steel reinforcement at the bottom:
Asb = 5 * (π * (32 mm / 2)^2)
Asb = 5 * (π * 16^2)
Asb = 5 * (π * 256)
Asb = 5 * 803.84
Asb = 4,019.20 mm^2
Now, let's calculate the width of the compression block:
b = width - cover - (Ø/2)
b = 1000 mm - 40 mm - 28 mm
b = 932 mm
Finally, we can calculate the depth of the compression block:
d = (310,000 mm^2 - 1,847.25 mm^2 - 4,019.20 mm^2) / 932 mm
d ≈ 302,133.55 mm^2 / 932 mm
d ≈ 324.38 mm
Therefore, the depth of the compression block is approximately 324.38 mm.
to know more about depth of the compression block ,click here -https://brainly.com/app/ask?q=depth+of+the+compression+block+
#SPJ11
The depth of the compression block in the middle of the beam is 370 mm. The ultimate moment capacity of the beam at the midspan is 564.9 kNm. The beam can sustain a uniform service live load of approximately 9.7 kN/m.
1. To determine the depth of the compression block, we need to calculate the distance from the extreme fiber to the centroid of the compression reinforcement. The distance from the extreme fiber to the centroid of the tension reinforcement can be found using the formula:
[tex]\[a_1 = \frac{n_1A_1y_1}{A_g}\][/tex]
where [tex]\(n_1\)[/tex] is the number of tension bars, [tex]\(A_1\)[/tex] is the area of one tension bar, [tex]\(y_1\)[/tex] is the distance from the extreme fiber to the centroid of one tension bar, and [tex]\(A_g\)[/tex] is the gross area of the beam.
Similarly, the distance from the extreme fiber to the centroid of the compression reinforcement is given by:
[tex]\[a_2 = \frac{n_2A_2y_2}{A_g}\][/tex]
where [tex]\(n_2\)[/tex] is the number of compression bars, [tex]\(A_2\)[/tex] is the area of one compression bar, and [tex]\(y_2\)[/tex] is the distance from the extreme fiber to the centroid of one compression bar.
The depth of the compression block is then given by:
[tex]\[d = a_2 + c\][/tex]
where c is the concrete cover.
Substituting the given values, we have:
[tex]\[d = \frac{5 \times (\pi(16 \times 10^{-3})^2) \times (700 \times 10^{-3})}{(1100 \times 350 \times 10^{-6})} + 40 = 370 \text{ mm}\][/tex]
2. The ultimate moment capacity of the beam at the midspan can be calculated using the formula:
[tex]\[M_u = \frac{f_y}{\gamma_s}A_gd\][/tex]
where [tex]\(f_y\)[/tex] is the yield strength of the reinforcement, [tex]\(\gamma_s\)[/tex] is the safety factor, [tex]\(A_g\)[/tex] is the gross area of the beam, and d is the depth of the compression block.
Substituting the given values, we have:
[tex]\[M_u = \frac{345 \times 10^6}{1.15} \times (1100 \times 350 \times 10^{-6}) \times 370 \times 10^{-3} = 564.9 \text{ kNm}\][/tex]
3. The uniform service live load that the beam can sustain can be determined by comparing the service moment capacity with the moment due to the live load. The service moment capacity is given by:
[tex]\[M_{svc} = \frac{f_y}{\gamma_s}A_gd_{svc}\][/tex]
where [tex]\(d_{svc}\)[/tex] is the depth of the compression block at service loads.
The moment due to the live load can be calculated using the equation:
[tex]\[M_{live} = \frac{wL^2}{8}\][/tex]
where w is the live load intensity and L is the span of the beam.
Equating [tex]\(M_{svc}\)[/tex] and [tex]\(M_{live}\)[/tex] and solving for w, we have:
[tex]\[w = \frac{8M_{svc}}{L^2}\][/tex]
Substituting the given values, we get:
[tex]\[w = \frac{8 \times \left(\frac{345 \times 10^6}{1.15} \times (1100 \times 350 \times 10^{-6}) \times 370 \times 10^{-3}\right)}{(5 \times 1.1)^2} \approx 9.7 \text{ kN/m}\][/tex]
To learn more about moment capacity refer:
https://brainly.com/question/31936847
#SPJ11
A polymer flows steadily in the horizontal pipe under the following conditions: p = 1000 kg/m3³; μ = 0.01 kg/m s, D = 0.03 m, and um = 0.3 m/s. Evaluate the following a. The Reynolds number b. The frictional dissipation per meter per kg flowing c. The pressure drop per meter
The Reynolds number is 900, the frictional dissipation per meter per kg flowing is 8, and the pressure drop per meter is 78480 Pa/m.
Density of the polymer, ρ = 1000 kg/m³
Dynamic viscosity of the polymer, μ = 0.01 kg/m s
Diameter of the pipe, D = 0.03 m
Average velocity of the polymer, um = 0.3 m/s
Reynolds number is defined as the ratio of inertial forces of a fluid to its viscous forces.
Reynolds number can be calculated as follows:
Re = ρuD/μ
Where:
ρ = 1000 kg/m³
u = 0.3 m/s
D = 0.03 m
μ = 0.01 kg/m s
Substituting these values in the formula:
Re = (1000 × 0.3 × 0.03) / 0.01
Re = 900
Frictional dissipation per meter per kg flowing is defined as the force per unit area required to maintain a given velocity gradient in a fluid over a fixed distance.
Frictional dissipation can be calculated as follows:
hf = (4fLρu²) / (2gD)
Where:
f = friction factor
L = length
u = velocity of the fluid in the pipe
D = diameter of the pipe
g = acceleration due to gravity
Substituting these values in the formula:
hf = (4fLρu²) / (2gD)
hf = (4 × 0.0268 × 1 × 0.3² × 1000) / (2 × 9.81 × 0.03)
hf = 8.00
Pressure drop per meter is defined as the loss of pressure when fluid flows through a pipe.
Pressure drop can be calculated as follows:
ΔP = hfρg
Where:
hf = frictional head loss per unit length
ρ = density of the fluid
g = acceleration due to gravity
Substituting these values in the formula:
ΔP = hfρg
ΔP = 8.00 × 1000 × 9.81
ΔP = 78480 Pa/m
Therefore, the Reynolds number is 900, the frictional dissipation per meter per kg flowing is 8, and the pressure drop per meter is 78480 Pa/m.
Learn more about Dynamic viscosity
https://brainly.com/question/30761521
#SPJ11
Consider the following: 2H2O(l) + 57 kJ <=> H3O+(aq) + OH-(aq) When the temperature of the above system is increased, the equilibrium shifts ..... Select one: a. right and Kw remains constant. b. left and Kw increases. c. right and Kw increases. d. right and Kw decreases. e. left and Kw decreases.
For [tex]2H_2O(l) + 57 kJ < = > H_3O+(aq) + OH-(aq)[/tex]When the temperature of the above system is increased, the equilibrium shifts : c. right and Kw increases.
When the temperature of the system represented by the given equation is increased, the equilibrium will shift. The specific direction of the shift can be determined by considering the heat as a reactant or product in the reaction.
In the given equation, heat is shown as a reactant with a positive enthalpy change (57 kJ). According to Le Chatelier's principle, an increase in temperature favors the endothermic reaction to absorb the added heat. In this case, the equilibrium will shift to the right to consume the excess heat.
As a result of the shift to the right, the concentration of H3O+ and OH- ions will increase, leading to an increase in the concentration of hydronium and hydroxide ions in the solution. Since Kw is the product of the concentrations of these ions ([tex]Kw = [H_3O+][OH-][/tex]), an increase in their concentrations will cause an increase in the value of Kw.
Therefore, the correct answer is: c. right and Kw increases.
Learn more about Le Chatelier's principle
https://brainly.com/question/29009512
#SPJ11
alculating the indefinite integral ∫x/(√8-2x-x^2)dx is -(√A-(x+1)^2)-arcsin B+C. Find A and B.
Partial fraction decomposition is a method used to convert a complicated fraction into simpler ones by decomposing the fraction into two or more parts such that each part has a simpler denominator.
Let us begin by finding the roots of the denominator. [tex]√8 - 2x - x² = 0 x² + 2x - √8 = 0[/tex] On solving the above quadratic equation, we obtain the values of x as x = - (1 + √9 + √8)/2 and x = - (1 + √9 - √8)/2
The roots of the quadratic equation are negative. Therefore, we can split the fraction into two parts based on the roots of the denominator.
[tex]∫x/(√8-2x-x²)dx = A/(x + (1 + √9 + √8)/2) + B/(x + (1 + √9 - √8)/2)[/tex]The values of A and B are to be determined by equating the above equation to the original one.
To know more about indefinite visit:
https://brainly.com/question/29059587
#SPJ11
For how many integers n with 1≤n≤2022 is the expression f(n)=n(n+3)/9 not equal to an integer?
There are 673 possible values for which[tex]$n = 3k+2$ and $f(n)$[/tex] is not an integer.
We are given the expression [tex]$f(n) = \frac{n(n+3)}{9}$[/tex] where[tex]$1 \leq n \leq 2022$.[/tex].there are a total of[tex]$673+673 = \boxed{1346}$[/tex]integers[tex]$n$[/tex]with [tex]$1 \leq n \leq 2022$[/tex] for which[tex]$f(n)$[/tex]is not an integer.
We need to find out how many integers $n$ are there such that $f(n)$ is not an integer.Let [tex]$n = 3k + r$[/tex]where [tex]$0 \leq r \leq 2$ and $k$[/tex] is a non-negative integer.
We will check the value o[tex]f $f(n)$[/tex]for each possible value of [tex]$r$.For $r = 0$[/tex], we have [tex]$$f(n) = \frac{n(n+3)}{9} = \frac{(3k)(3k+3)}{9} = k(k+1)$$[/tex]which is always an integer.
Thus, no values of [tex]$n$[/tex] with[tex]$r=0$[/tex] will work.
For [tex]$r = 1$[/tex], we have [tex]$$f(n) = \frac{n(n+3)}{9} = \frac{(3k+1)(3k+4)}{9} = (3k+1)(k+1) + \frac{k(k+1)}{3}$$[/tex]which is not an integer if and only if [tex]$\frac{k(k+1)}{3}$[/tex] is not an integer.
This happens if and only if[tex]$k \equiv 2 \mod 3$ or $k \equiv 0 \mod 3$.[/tex]
Thus, there are [tex]$\left\lfloor\frac{2022-1}{3}\right\rfloor = 673$[/tex] possible values of[tex]$k$[/tex]for which[tex]$n = 3k+1$ and $f(n)$[/tex]is not an integer.
For[tex]$r = 2$[/tex], we have[tex]$$f(n) = \frac{n(n+3)}{9} = \frac{(3k+2)(3k+5)}{9} = (3k+2)(k+1) + \frac{2k(k+1)}{3}$$[/tex]which is not an integer if and only if[tex]$\frac{2k(k+1)}{3}$[/tex] is not an integer.
This happens if and only i[tex]f $k \equiv 1 \mod 3$ or $k \equiv 0 \mod 3$.[/tex]
Thus, there are [tex]$\left\lfloor\frac{2022-2}{3}\right\rfloor = 673$[/tex] possible values of[tex]$k$[/tex]for which[tex]$n = 3k+2$ and $f(n)$[/tex] is not an integer.
To know more about expression visit:
https://brainly.com/question/28170201
#SPJ11
The overall enthalpy change for the combustion reaction of gaseous butane can be represented in various ways. Write/show the enthalpy change using the four methods of representing the equation learned in this unit
The enthalpy change for the combustion of gaseous butane can be represented using methods such as standard enthalpy change, enthalpy change per mole of reaction, enthalpy change per mole of substance, and bond enthalpy.
The combustion reaction of gaseous butane (C₄H₁₀) can be represented in different ways to show the enthalpy change. Here are the four methods of representing the equation and the corresponding enthalpy change:
Standard Enthalpy Change (ΔH°):
C₄H₁₀(g) + 13/2 O₂(g) → 4CO₂(g) + 5H₂O(g)
ΔH° = -2877 kJ/mol (Negative sign indicates exothermic reaction)
Enthalpy Change per Mole of Reaction (ΔH):
C₄H₁₀(g) + 13/2 O₂(g) → 4CO₂(g) + 5H₂O(g)
ΔH = -2877 kJ (For the given stoichiometry of the reaction)
Enthalpy Change per Mole of Substance (ΔHf):
ΔHf[C₄H₁₀(g)] = -125.5 kJ/mol (Enthalpy change for 1 mole of gaseous butane)
Bond Enthalpy (ΔHb):
ΔHb = Σ(ΔHb[reactants]) - Σ(ΔHb[products])
ΔHb = [4ΔHb(C=O) + 5ΔHb(O-H)] - [10ΔHb(C-H)]
Note: ΔHb represents the bond enthalpy change for the given reaction.
To know more about enthalpy change,
https://brainly.com/question/30014232
#SPJ11
Kendra has an unlimited supply of unbreakable sticks of length $2$, $4$ and $6$ inches. Using these sticks, how many non-congruent triangles can she make if each side is made with a whole stick? two sticks can be joined only at a vertex of the triangle. (a triangle with sides of lengths $4$, $6$, $6$ is an example of one such triangle to be included, whereas a triangle with sides of lengths $2$, $2$, $4$ should not be included. )
Answer:
5
Step-by-step explanation:
You want to know the number of non-congruent triangles that can be formed with side lengths of 2 or 4 or 6.
Triangle inequalityThe triangle inequality requires the sum of the two shorter sides exceed the length of the longest side. Possible triangles from these side lengths are ...
{2, 2, 2} or {4, 4, 4} or {6, 6, 6} . . . . . an equilateral triangle
{2, 4, 4}
{2, 6, 6}
{4, 4, 6}
{4, 6, 6}
That is, 5 different triangle shapes can be formed from these side lengths.
<95141404393>
The number of visitors P to a website in a given week over a 1-year period is given by Pt) 120+ (-80) where t is the week and 1sts52 a) Over what interval of time during the 1-year period is the number of visitor decreasing?
b) Over what interval of time during the 1-year period is the number of visitors increasing?
c) Find the critical point, and interpret its meaning
a) The number of visitors is decreasing over the entire 1-year period.
b) There is no interval of time where the number of visitors is increasing.
c) There is no critical point, meaning the number of visitors does not have any maximum or minimum points.
The number of visitors P to a website in a given week over a 1-year period is given by Pt) = 120 + (-80)t, where t is the week.
a) To determine when the number of visitors is decreasing, we need to find the interval of time where the derivative of Pt) is negative. The derivative of Pt) is -80, which is a constant value. Since -80 is always negative, the number of visitors is decreasing over the entire 1-year period.
b) Similarly, to determine when the number of visitors is increasing, we need to find the interval of time where the derivative of Pt) is positive. Since the derivative is always -80, which is negative, there is no interval of time where the number of visitors is increasing.
c) The critical point is a point where the derivative of Pt) is zero. In this case, since the derivative is always -80, there is no critical point. This means that the number of visitors does not have any maximum or minimum points, and it is always decreasing.
Learn more about critical point :
https://brainly.com/question/30760896
#SPJ11
A patient with a weight of 166 lbs is suffering from bacterial pneumonia. The doctor prescribes the antibiotic, Cefaclor, with a total of 45 mg/kg each day. If the drug is divided into 3 doses and is available in a solution of 125 mg/mL, how many mL would the nurse administer per dose?
the nurse would administer approximately 9.0355 mL of Cefaclor solution per dose.
To determine the amount of Cefaclor solution (in mL) the nurse would administer per dose, we need to calculate the total daily dosage of Cefaclor for the patient and divide it by the number of doses.
Given:
Patient's weight: 166 lbs
Total daily dosage: 45 mg/kg
Cefaclor solution concentration: 125 mg/mL
Number of doses: 3
First, we need to convert the patient's weight from pounds to kilograms:
166 lbs * (1 kg / 2.2046 lbs) ≈ 75.296 kg
Next, we calculate the total daily dosage of Cefaclor for the patient:
Total daily dosage = 45 mg/kg * 75.296 kg ≈ 3388.32 mg
Now, we divide the total daily dosage by the number of doses to get the dosage per dose:
Dosage per dose = 3388.32 mg / 3 ≈ 1129.44 mg
Finally, we convert the dosage per dose from milligrams to milliliters using the concentration of the Cefaclor solution:
Dosage per dose in mL = Dosage per dose in mg / Solution concentration in mg/mL
Dosage per dose in mL = 1129.44 mg / 125 mg/mL ≈ 9.0355 mL
To know more about concentration visit:
brainly.com/question/10725862
#SPJ11
A field measurement of 1751.71 ft was made with a steel chain, which was later standardized at a true length of 100.014 ft. What is the true distance measured?
The true distance measured is 1751.71 ft. To find the true distance measured, we can use the concept of proportional relationships.
Let's denote the measured distance as D1 and the true length as D2.
According to the given information, the measured distance with the steel chain is 1751.71 ft, and the true length of the chain is 100.014 ft.
We can set up a proportion to relate the measured distance to the true length:
D1 / D2 = Measured length / True length
Plugging in the given values:
D1 / D2 = 1751.71 ft / 100.014 ft
To find the true distance measured (D2), we can rearrange the equation and solve for D2:
D2 = (D1 * True length) / Measured length
Substituting the given values:
D2 = (1751.71 ft * 100.014 ft) / 100.014 ft
Calculating:
D2 = 1751.71 ft
Therefore, the true distance measured is 1751.71 ft.
To know more about distance visit :
https://brainly.com/question/13034462
#SPJ11
Can someone show me how to work this problem?
The correct statement regarding the similarity of the triangles in this problem is given as follows:
similar; RYL by SAS similarity.
What is the Side-Angle-Side congruence theorem?The Side-Angle-Side (SAS) congruence theorem states that if two sides of two similar triangles form a proportional relationship, and the angle measure between these two triangles is the same, then the two triangles are congruent.
In this problem, we have that the angle R is equals for both triangles, and the two sides between the angle R in each triangle form a proportional relationship.
Hence the SAS theorem holds true for the triangle in this problem.
More can be learned about congruence theorems at brainly.com/question/3168048
#SPJ1
100 POINT!!!!!!! PLEASE HELP ME WITH THIS QUICLKY.
Answer:
1) AB ~ EF, BC ~ FG, CD ~ GH, AD ~ EH
2) Angle A is congruent to angle E.
Angle B is congruent to angle F.
Angle C is congruent to angle G.
Angle D is congruent to angle H.
3) AD = BC = 8, CD = (2/3)(6) = 4, so
AB = 3(4) = 12, EF = (3/2)(12) = 18,
EH = FG = (2/3)(8) = 12
Perimeter of ABCD = 12 + 8 + 8 + 4
= 32 cm
Perimeter of EFGH = 18 + 12 + 12 + 6
= 48 cm
(i) Find all first and second order partial derivatives of f(x, y) = x²y + cos(ry) (ii) Find xy² lim (z,y) ›(0,0) ³+y³ if the limit exists. If it does not exist, explain why.
the limit of a function as (z, y) approaches (0, 0) can only exist if the limit is the same regardless of the path taken to approach the point. If the limit depends on the path taken, then the limit does not exist.
(i) To find the first and second-order partial derivatives of f(x, y) = x²y + cos(ry), we differentiate the function with respect to each variable separately.
First-order partial derivatives:
∂f/∂x = 2xy
∂f/∂y = x² - r sin(ry)
Second-order partial derivatives:
∂²f/∂x² = 2y
∂²f/∂y² = -r²cos(ry)
∂²f/∂x∂y = 2x - r²sin(ry)
(ii) To find the limit lim(z, y)→(0, 0) of xy² if it exists, we substitute the given values into the expression xy² and evaluate the result.
lim(z, y)→(0, 0) xy² = 0 * 0² = 0
In this case, the limit is 0. However, it's important to note that the limit of a function as (z, y) approaches (0, 0) can only exist if the limit is the same regardless of the path taken to approach the point. If the limit depends on the path taken, then the limit does not exist.
learn more about function
brainly.com/question/30721594
#SPJ11
Solve the equation 4/x+7=2 a) x=1 b) x=−7 c) x=−5 d) no solution
The given equation is: `4/x+7 = 2`To solve the equation, we'll isolate x.
The first step is to get rid of the fraction, we can do that by multiplying both sides of the equation by `x + 7`:`(x + 7) * 4/(x + 7) = 2(x + 7)` Simplify:`4 = 2x + 14`
Subtract 14 from both sides:`-10 = 2x`
Solve for `x` by dividing both sides by 2:`x = -5. `Therefore, the answer is option c) x = -5
To solve the equation `4/x+7 = 2`, we multiply both sides of the equation by `(x + 7)` to eliminate the fraction, and simplify the resulting equation to obtain `x = -5`.
To solve the given equation 4/x+7 = 2, we will multiply both sides of the equation by (x + 7) to eliminate the fraction. The equation now becomes 4 = 2(x + 7).
Simplifying this expression by using the distributive property on the right-hand side, we obtain 4 = 2x + 14.
Next, we subtract 14 from both sides of the equation to isolate the variable `x`. The resulting equation is -10 = 2x.
We now divide both sides of the equation by 2 to obtain the value of `x`. Thus, x = -5.
Therefore, the answer is option c) x = -5.
In conclusion, the solution of the given equation 4/x+7 = 2 is x = -5. To obtain this result, we eliminated the fraction by multiplying both sides of the equation by (x + 7). Then, we simplified the resulting equation and isolated the variable x. Finally, we obtained the value of `x` by dividing both sides of the equation by 2.
To learn more about distributive property visit:
brainly.com/question/30321732
#SPJ11
In the equation x^2+10x+24=(x+a)(x+b), b is an integer. Find algebraically all possible values of b.
Answer:
b = 4, b = 6
Step-by-step explanation:
consider the left side
x² + 10x + 24
consider the factors of the constant term (+ 24) which sum to give the coefficient of the x- term (+ 10)
the factors are + 4 and + 6
then
x² + 10x + 24 = (x + 4)(x + 6) = (x + 6)(x + 4)
then (x + b) = (x + 4) or (x + 6)
with b = 4 or b = 6
a) evaluate the sum b) Prove the formula (2-1) = N². i=0
To evaluate the sum and prove the formula (2-1) = N², where i ranges from 0 to N, we can use mathematical induction.
Step 1: Base Case
Let's start with the base case where N = 0. In this case, the sum becomes:
(2-1) = 0²
On the left side, we have 1, and on the right side, we have 0. Both sides are equal, so the formula holds true for the base case.
Step 2: Inductive Hypothesis
Assume that the formula holds true for some arbitrary positive integer k, i.e., (2-1) + (2-1) + ... + (2-1) (k times) = k².
Step 3: Inductive Step
We need to prove that the formula holds for the next positive integer k+1, i.e., (2-1) + (2-1) + ... + (2-1) ((k+1) times) = (k+1)².
Let's consider the sum for k+1:
(2-1) + (2-1) + ... + (2-1) ((k+1) times)
We can rewrite this sum as:
[(2-1) + (2-1) + ... + (2-1) (k times)] + (2-1)
Using the inductive hypothesis, we can substitute the sum in square brackets with k²:
k² + (2-1)
Simplifying further, we get:
k² + 1
Now, let's evaluate (k+1)²:
(k+1)² = k² + 2k + 1
Comparing this with the expression k² + 1, we can see that they are equal.
Step 4: Conclusion
Based on the base case and the inductive step, we can conclude that the formula (2-1) = N² holds for all positive integers N, as the formula is true for N = 0 and assuming it holds for k implies it holds for k+1.
Therefore, we have proven the formula (2-1) = N² for all positive integers N.
Learn more about Hypothesis here:
https://brainly.com/question/29576929
#SPJ11
Question 4(Multiple Choice Worth 2 points)
(Volume of Cylinders MC)
A cylinder has a volume of
O
12
7-6
74
O
7/2
inches
inches
inches
inches
22
1in³ and a radius of in. What is the height of a cylinder? Approximate using =
The height of the cylinder is [tex]\frac{7}{2}[/tex] inches.
How to solveA cylinder is a 3-dimensional solid shape with a lateral surface and 2 circular surfaces.
Volume of a cylinder(V) is : [tex]\pi r^{2} hr[/tex] = 1/3 inches
volume = [tex]\frac{2}{9}in^{3}[/tex]
Making h the subject of the Formula we have:
h = [tex]\frac{V}{\pi r^{2} }h[/tex]
= [tex]1\frac{2}{9}in^{3}[/tex] ÷ [tex](\frac{1}{3}) ^{2}[/tex] = [tex]\frac{7}{2}[/tex] inches
Learn more about cylinders:
https://brainly.com/question/23935577
#SPJ4
The last dividend per share paid on a stock was $1.20. The dividend grows at 30% per year for one year (year 1) and at a constant rate of 6% thereafter. If the market capitalization rate is 12%, what is the estimated intrinsic value per share today? Enter your answer with two decimals.
The estimated intrinsic value per share today is approximately $27.39, calculated using the dividend discount model with a 30% dividend growth rate in Year 1 and a 6% constant growth rate thereafter, and a market capitalization rate of 12%.
To calculate the estimated intrinsic value per share today, we need to determine the present value of the future dividends using the dividend discount model.
The dividend discount model (DDM) formula is as follows:
Intrinsic Value = Dividend / (Discount Rate - Dividend Growth Rate)
Given the information provided:
Dividend in Year 1 = $1.20 * (1 + 30%) = $1.56
Dividend Growth Rate in Year 1 = 30%
Dividend Growth Rate from Year 2 onwards = 6%
Discount Rate = 12%
Now, let's calculate the present value of dividends for the perpetuity period (from Year 2 onwards) using the constant growth rate formula:
Present Value of Perpetuity Dividends = Dividend / (Discount Rate - Dividend Growth Rate)
Present Value of Perpetuity Dividends = $1.56 / (0.12 - 0.06) = $1.56 / 0.06 = $26.00
Next, we need to calculate the present value of the dividend in Year 1:
Present Value of Dividend in Year 1 = Dividend / (1 + Discount Rate)
Present Value of Dividend in Year 1 = $1.56 / (1 + 0.12) = $1.56 / 1.12 = $1.39
Finally, we can calculate the estimated intrinsic value per share today by summing the present value of dividends for Year 1 and the perpetuity period:
Intrinsic Value = Present Value of Dividend in Year 1 + Present Value of Perpetuity Dividends
Intrinsic Value = $1.39 + $26.00 = $27.39
Therefore, the estimated intrinsic value per share today is approximately $27.39.
Learn more about the intrinsic value
brainly.com/question/30764018
#SPJ11