The annual average runoff for the watershed is 100 mm.
To determine the annual average runoff, we need to calculate the difference between the precipitation and evapotranspiration.
Given:
Precipitation = 300 mm
Evapotranspiration = 200 mm
To find the annual average runoff, we subtract the evapotranspiration from the precipitation:
Annual Average Runoff = Precipitation - Evapotranspiration
Annual Average Runoff = 300 mm - 200 mm
Annual Average Runoff = 100 mm
Therefore, The watershed's average annual runoff is 100 mm.
learn more about average from given link
https://brainly.com/question/130657
#SPJ11
Consider a system at 200 K which has an infinite ladder of evenly spaced quantum states with an energy spacing of 0.25 kJ/mol. 1. (5%) The energy for level n=3 is kJ/mol. 2. (5%) The minimum possible value of the partition function for this system is 3. (5%) The average energy of this system in the classical limit is kj/mol. [Answer rounded to 1 decimal] 4. (5%) The number of thermally populated states is [Answer should be whole number]
The number of thermally populated states is 0.
Given that the system at 200 K has an infinite ladder of evenly spaced quantum states with an energy spacing of 0.25 kJ/mol. We need to find the energy for level n=3, the minimum possible value of the partition function, the average energy of this system in the classical limit, and the number of thermally populated states.1. The energy for level n=3 is kJ/mol.
The energy for level n can be calculated as,
En = (n - 1/2) * δE
Where δE is the energy spacing
δE = 0.25 kJ/mol and n = 3
En = (3 - 1/2) * 0.25= 0.625 kJ/mol
Therefore, the energy for level n=3 is 0.625 kJ/mol.
The minimum possible value of the partition function for this system is - We know that the partition function is given as,
Z= Σexp(-Ei/kT)
where the sum is over all states of the system.
The minimum possible value of the partition function can be calculated by considering the lowest energy state of the system, which is level n = 1.
Z1 = exp(-E1/kT) = exp(-0.125/kT)
For an infinite ladder of quantum states, the partition function for the system is given as,
Z = Z1 + Z2 + Z3 + … = Σexp(-Ei/kT)
The minimum possible value of the partition function is when only the ground state (n=1) is populated, and all other states are unoccupied.
Zmin = Z1 = exp(-0.125/kT) = exp(-5000/T)
The average energy of this system in the classical limit is kj/mol. The classical limit is when the spacing between energy levels is much less than the thermal energy. In this case, δE << kT. In the classical limit, the average energy of the system can be calculated as,
Eav = kT/2= (1.38 * 10^-23 J/K) * (200 K) / 2= 1.38 * 10^-21 J= 0.331 kJ/mol
Therefore, the average energy of this system in the classical limit is 0.331 kJ/mol (rounded to 1 decimal).
The number of thermally populated states is
The number of thermally populated states can be calculated using the formula,
N= Σ exp(-Ei/kT) / Z
where the sum is over all states of the system that have energies less than or equal to the thermal energy.
Using the values from part 1, we can calculate the number of thermally populated states,
N = Σ exp(-Ei/kT) / Z= exp(-0.125/kT) / (1 + exp(-0.125/kT) + exp(-0.375/kT) + …)
We need to sum over all states that have energies less than or equal to the thermal energy, which is given by,
En = (n - 1/2) * δE ≤ kT
This inequality can be solved for n to get, n ≤ (kT/δE) + 1/2
The number of thermally populated states is therefore given by,
N = Σn=1 to (kT/δE) + 1/2 exp(-(n-1/2)δE/kT) / Z= exp(-0.125/kT) / (1 + exp(-0.125/kT) + exp(-0.375/kT))= 0.431 (rounded to the nearest whole number)
Therefore, the number of thermally populated states is 0.
Learn more about partition function visit:
brainly.com/question/32762167
#SPJ11
H. Elourine vs. chlorine Which one will have the higher electron affinity and why?
Overall, due to the combination of a higher effective nuclear charge and greater electron shielding, chlorine exhibits a higher electron affinity than fluorine.
Chlorine (Cl) will generally have a higher electron affinity compared to fluorine (F). Electron affinity is the energy change that occurs when an atom gains an electron in the gaseous state. Chlorine has a higher electron affinity than fluorine due to two main factors:
Effective Nuclear Charge: Chlorine has a larger atomic number and more protons in its nucleus compared to fluorine. The increased positive charge in the nucleus of chlorine attracts electrons more strongly, resulting in a higher electron affinity.
Electron Shielding: Chlorine has more electron shells compared to fluorine. The presence of inner electron shells in chlorine provides greater shielding or repulsion from the outer electrons, reducing the electron-electron repulsion and allowing the nucleus to exert a stronger attraction on an incoming electron.
To know more about electron affinity,
https://brainly.com/question/1542518
#SPJ11
V= 1/3 a2 h solve for h
A 47.6g sample was found to consist of 35.0% oxygen by mass with
the remaining mass being calcium, calculate the mass of calcium in
the sample.
The mass of calcium in the sample is 30.94 g.
To calculate the mass of calcium, we first need to determine the mass of oxygen in the sample. We know that the sample consists of 35.0% oxygen by mass, so we can calculate the mass of oxygen using the given sample mass of 47.6 g:
Mass of oxygen = 35.0% * 47.6 g = 0.35 * 47.6 g = 16.66 g.
Since the remaining mass in the sample is calcium, we can calculate the mass of calcium by subtracting the mass of oxygen from the sample mass:
Mass of calcium = Sample mass - Mass of oxygen = 47.6 g - 16.66 g = 30.94 g.
Therefore, the mass of calcium in the sample is 30.94 g.
Know more about oxygen here:
https://brainly.com/question/33311650
#SPJ11
A gaseous mixture contains 431.0 Torr H₂(g), 388.5 Torr N₂(g), and 82.7 Torr Ar(g). Calculate the mole fraction, x, of each of 2 these gases. XH₂ = XN₂ = XAr =
the mole fractions are approximately:
XH₂ = 0.387
XN₂ = 0.348
XAr = 0.074
To calculate the mole fraction of each gas in the mixture, we need to divide the partial pressure of each gas by the total pressure of the mixture.
Given:
Partial pressure of H₂ (PH₂) = 431.0 Torr
Partial pressure of N₂ (PN₂) = 388.5 Torr
Partial pressure of Ar (PAr) = 82.7 Torr
Total pressure of the mixture (Ptotal) = PH₂ + PN₂ + PAr
Now, let's calculate the mole fraction (X) for each gas:
XH₂ = PH₂ / Ptotal
XN₂ = PN₂ / Ptotal
XAr = PAr / Ptotal
Substituting the given values into the equations:
XH₂ = 431.0 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
XN₂ = 388.5 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
XAr = 82.7 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
Calculating the values:
XH₂ ≈ 0.387
XN₂ ≈ 0.348
XAr ≈ 0.074
Therefore, the mole fractions are approximately:
XH₂ = 0.387
XN₂ = 0.348
XAr = 0.074
To learn more about fractions visit:
https://brainly.com/question/30154928
#SPJ11
nts Incorrect Question 2 0/2.5 pts At an abandoned waste site, you find a 10,000 L tank contaminated with Chemical Z at a concentration of 2.7 mg/L. You cannot pump the water into the local sewer unless the concentration is below 0.5 mg/L. One idea for treating the water is to add activated carbon until you reach the allowable concentration, then you can filter out the carbon and dispose of it at a hazardous waste landfill. Lab tests show that the linear partitioning coefficient for Chemical Z and the activated carbon is 4.1 L/g. Calculate how much activated carbon (in kg) to purchase. 4 Enter your final answer with 2 decimal places. 189.42
We are given a 10,000 L tank contaminated with Chemical Z at a concentration of 2.7 mg/L.
We know that,
Ci = 2.7 mg/LCe = 0.5 mg/LPC = 4.1 L/g
Volume of contaminated water = 10,000 L
= 10,000,000 mL Putting all the values in the formula, Mass of activated carbon = (10,000,000 mL × (2.7 − 0.5))/4.1 = 6,900,000/4.1
= 1,682,926.8 mL
We need to convert this volume to mass, Mass = volume × density Density of activated carbon = 0.5 g/mLTherefore, Mass of activated carbon
= 1,682,926.8 mL × 0.5 g/mL
= 841,463.4 g
= 841.46 kg
To know more about concentration, visit :
https://brainly.com/question/30862855
#SPJ11
To treat the contaminated water and bring the concentration of Chemical Z below 0.5 mg/L, approximately 6.59 kg of activated carbon should be purchased.
To calculate the amount of activated carbon needed to treat the contaminated water, we can use the linear partitioning coefficient. This coefficient tells us the ratio of the concentration of Chemical Z in the activated carbon to the concentration in the water. In this case, the coefficient is 4.1 L/g.
First, we need to determine the mass of Chemical Z in the tank. The concentration is given as 2.7 mg/L, and the volume of the tank is 10,000 L. Multiplying these values gives us 27,000 mg of Chemical Z in the tank.
Next, we divide the mass of Chemical Z in the tank by the linear partitioning coefficient to find the mass of activated carbon needed. In this case, we divide 27,000 mg by 4.1 L/g, which gives us 6,585.37 g.
To convert the mass to kilograms, we divide by 1000. So, the amount of activated carbon to purchase is 6.58537 kg.
Therefore, the answer is 6.59 kg (rounded to two decimal places).
Learn more about concentration
https://brainly.com/question/30862855
#SPJ11
If 1800 m°/d of wastewater from an industry has a BODs of 190
mg/L and k = 0.17/day (base 10)
a. How much oxygen is required to satisfy the demand for BODs of
this residue assuming that 1 kg of oxygen must be supplied by
kilogram of final BOD in the residue
b. What is the population equivalent of these wastes (besed in
BOD5)?
(a) The amount of oxygen required to satisfy the demand for BODs in this residue is 578,100 kg/d.
(b) The population equivalent of these wastes, based on BOD₅, is 5,700,000 population.
a. To calculate the amount of oxygen required to satisfy the demand for BODs, we can use the formula:
Oxygen required = Flow rate * BODs * k
Given that the flow rate is 1800 m³/d, the BODs is 190 mg/L, and k is 0.17/day, we can substitute these values into the formula:
Oxygen required = 1800 m³/d * 190 mg/L * 0.17/day
To ensure consistent units, we need to convert the flow rate from m³/d to L/d:
1800 m³/d * 1000 L/m³ = 1,800,000 L/d
Now we can substitute this value into the formula:
Oxygen required = 1,800,000 L/d * 190 mg/L * 0.17/day
Simplifying the calculation:
Oxygen required = 578,100,000 mg/d
To convert mg to kg, we divide by 1000:
Oxygen required = 578,100 kg/d
Therefore, the amount of oxygen required to satisfy the demand for BODs in this residue is 578,100 kg/d.
b. To calculate the population equivalent of these wastes based on BOD₅, we need to know the BOD₅ value for the wastewater. The BOD₅ value represents the amount of dissolved oxygen consumed over a 5-day period.
If we assume the BOD₅ value is the same as the BODs value, which is 190 mg/L, we can use the following formula:
Population equivalent = (Flow rate * BOD₅) / 60 g/day
Given that the flow rate is 1800 m³/d and the BOD₅ is 190 mg/L, we can substitute these values into the formula:
Population equivalent = (1800 m³/d * 190 mg/L) / 60 g/day
To ensure consistent units, we need to convert the flow rate from m³/d to L/d:
1800 m³/d * 1000 L/m³ = 1,800,000 L/d
Now we can substitute this value into the formula:
Population equivalent = (1,800,000 L/d * 190 mg/L) / 60 g/day
Simplifying the calculation:
Population equivalent = 5,700,000 population
Therefore, the population equivalent of these wastes, based on BOD₅, is 5,700,000 population.
Know more about population equivalent:
https://brainly.com/question/33840792
#SPJ11
A simply supported T beam has a simple span of 3m. The thickness of the slab is 110mm. The width of its web is 350mm. If the center to center spacing between beams is 2m, determine the effective flange width of the T beam.
The effective flange width of the given T beam with a simple span of 3m, a slab thickness of 110mm, and a web width of 350mm is calculated to be 1.65 meters.
The effective flange width represents the distance from the centerline of the web to the edge of the flange where it can contribute to the load-carrying capacity of the T beam. In a T beam, the flange is responsible for resisting bending stresses.
Given that the centre-to-centre spacing between beams is 2m, we need to determine the distance from the centerline of the web to the edge of the flange. This can be calculated by subtracting the width of the web from the centre-to-centre spacing.
The width of the web is given as 350mm, which needs to be converted to meters (0.35m). Subtracting the width of the web from the centre-to-centre spacing gives us the effective flange width:
Effective flange width = 2m - 0.35m
Effective flange width = 1.65m
Therefore, the effective flange width of the T beam is 1.65 meters.
To learn more about simple span refer:
https://brainly.com/question/29939115
#SPJ11
b) After allowing 16% discount on the marked price of a watch, 13% Value Added Tax (VAT) was levied on it. If the watch was sold for Rs 4,746, calculate the marked price of the watch.
Note: Show step-by-step solution.
A highway fill stretches between stations 5+040 and 5+140 with a uniform ground slope. It has a side slope of 2: 1 and width of the roadway is 10 {~m} . Determine the Fol
The Fol for the given highway fill with a side slope of 2:1 and a roadway width of 10 meters is 1:1. This means that for every 1 unit of horizontal distance, there is a 1-unit increase in elevation.
To determine the Fol, we need to understand the given information and use it to calculate the required value.
Here are the steps to find the Fol:
1. Calculate the difference in elevation between the two stations: 5+140 - 5+040 = 100 meters. This represents the change in height along the highway fill.
2. Determine the horizontal distance between the two stations. Since the width of the roadway is given as 10 meters, the horizontal distance will be the same as the length of the roadway. Therefore, the horizontal distance is 100 meters.
3. Calculate the slope ratio, which is the side slope given as 2:1. This means that for every 2 units of horizontal distance, there is a 1-unit increase in elevation.
4. Divide the difference in elevation by the horizontal distance to find the slope ratio: 100 meters / 100 meters = 1.
5. Compare the slope ratio to the given side slope ratio. Since the calculated slope ratio is 1 and the given side slope ratio is 2:1, we can conclude that the calculated slope is steeper than the given side slope.
6. Finally, determine the Fol. The Fol represents the ratio of the horizontal distance to the vertical distance. In this case, the horizontal distance is 100 meters, and the vertical distance is 100 meters. Therefore, the Fol is 1:1.
To summarize, Fol is equal to 1:1 for the provided highway fill with a side slope of 2:1 and a 10 metre wide roadway. This implies that the height increases by one unit for every unit of horizontal distance.
learn more about slope from given link
https://brainly.com/question/27781455
#SPJ11
42. What is the bearing of lines having the following azimuths? a. 354° 10' 29" bearing: b. 54° 07' 21" bearing: c. 134° 19' 56" bearing: » d. 235° 44' 33" bearing
The bearings of lines having the following azimuths:
a) 354° 10' 29" is approximately 95° 49' 31"
b) 54° 07' 21" is approximately 35° 52' 39"
c) 134° 19' 56" is approximately 315° 40' 04"
d) 235° 44' 33" is approximately 214° 15' 27"
In order to determine the bearing of a line having a certain azimuth, the following formula is used:
Bearing = 90° − Azimuth (for azimuths less than 180°)
Bearing = 450° − Azimuth (for azimuths greater than 180°)
Given azimuth a) 354° 10' 29"
Bearing = 90° - 354° 10' 29"
Convert 10' 29" to decimal degrees by dividing it by 60: 1
0/60 + 29/3600 = 0.1747°
Bearing = 90° - 354° 10' 29"
= 90° - (354 + 0.1747)
= 90° - 354.1747°
= -264.1747°
Bearing should be between 0° and 360° so we need to add 360° to make it positive:
Bearing = -264.1747° + 360°
= 95.8253°
Therefore, the bearing for azimuth 354° 10' 29" is approximately
95° 49' 31"
Given azimuth b) 54° 07' 21"
Bearing = 90° - 54° 07' 21"
Convert 07' 21" to decimal degrees by dividing it by 60:
7/60 + 21/3600 = 0.1225°
Bearing = 90° - 54° 07' 21"
= 90° - (54 + 0.1225)
= 90° - 54.1225°
= 35.8775°
Therefore, the bearing for azimuth 54° 07' 21" is approximately
35° 52' 39"
Given azimuth c) 134° 19' 56"
Bearing = 90° - 134° 19' 56"
Convert 19' 56" to decimal degrees by dividing it by 60:
19/60 + 56/3600 = 0.3322°
Bearing = 90° - 134° 19' 56"
= 90° - (134 + 0.3322)
= 90° - 134.3322°
= -44.3322°
Bearing should be between 0° and 360° so we need to add 360° to make it positive:
Bearing = -44.3322° + 360°
= 315.6678°
Therefore, the bearing for azimuth 134° 19' 56" is approximately
315° 40' 04"
Given azimuth d) 235° 44' 33"
Bearing = 450° - 235° 44' 33"
Convert 44' 33" to decimal degrees by dividing it by 60:
44/60 + 33/3600 = 0.7425°
Bearing = 450° - 235° 44' 33"
= 450° - (235 + 0.7425)
= 450° - 235.7425°
= 214.2575°
Therefore, the bearing for azimuth 235° 44' 33" is approximately
214° 15' 27"
Thus, the bearings of lines having the following azimuths:
a) 354° 10' 29" is approximately 95° 49' 31"
b) 54° 07' 21" is approximately 35° 52' 39"
c) 134° 19' 56" is approximately 315° 40' 04"
d) 235° 44' 33" is approximately 214° 15' 27"
To know more about formula, visit:
https://brainly.com/question/20748250
#SPJ11
An individual's per kg expenditure on coffee is distributed with mean $2.32 and variance 0.09 If each individual in the population drinks 3 kg of tea and 2 kg of coffee, the mean total expenditure an beverages is $ with a variance of □, If T and C have a bivariate normal distribution with covariance zero, the mean total expenditure an beverages is $□ with a variance of □. If X and Y have a bivariate distribution with covariance zero, this implies that the variables show
The mean total expenditure on beverages is $736 with a variance of $8.1912.
If X and Y have a bivariate distribution with covariance zero, this implies that the variables show no linear relationship.
Given that an individual's per kg expenditure on coffee is distributed with mean $2.32 and variance 0.09.
Each individual in the population drinks 3 kg of tea and 2 kg of coffee.
Let T and C be the amount spent on tea and coffee respectively by an individual.
Then,
Total expenditure on coffee = 2 × 2.32 × 100 = $232
and,
Total expenditure on tea = 3 × 1.68 × 100 = $504
We know that the covariance of T and C is zero.
Thus, Mean of the total expenditure on beverages = 232 + 504 = $736,
The variance of the total expenditure on beverages = 4 × variance of expenditure on coffee + 9 × variance of expenditure on tea
= 4 × 0.09 × (2.32)² + 9 × 0.04 × (1.68)²
= $8.1912
Hence, the mean total expenditure on beverages is $736 with a variance of $8.1912.
If X and Y have a bivariate distribution with covariance zero, this implies that the variables show no linear relationship.
To know more about linear relationship visit:
https://brainly.com/question/29066440
#SPJ11
Create a question which uses the cardinal directions (North, South, East, West), similar to the boat example in Exercise 1, or a question using 2 triangles (similar to the ones in Exercise 2 and 3 ), or one similar to the last 3 questions shown in the "Extend your skills" at the very end of the lesson
To answer this question step-by-step:
1. Start at point A.
2. Walk 5 kilometers north. This means you would be moving in the direction opposite to the South.
3. After walking 5 kilometers north, you are now at a new point.
4. From this new point, walk 3 kilometers east. This means you would be moving in the direction opposite to the West.
5. After walking 3 kilometers east, you are at another new point.
6. From this second new point, walk 2 kilometers south. This means you would be moving in the direction opposite to the North.
7. After walking 2 kilometers south, you would end up at the final destination.
By following these steps, you would end up at a specific location based on the cardinal directions given in the question.
To know more about uses cardinal directions:
https://brainly.in/question/35610135
#SPJ11
A peach is 7 times as heavy as an olive. The peach also weighs 900 grams more than the olive. What is the total weight in kilograms for the peach and olive?
Attempt to write the dehydration reaction of ethyl alcohol using H_2SO_4 as a catalyst at 180 °C ---
The dehydration reaction of ethyl alcohol using H2SO4 as a catalyst at 180 °C results in the formation of ethylene gas and water.
Dehydration is a chemical reaction that involves the removal of water molecules from a compound. In this case, when ethyl alcohol (C2H5OH) is subjected to the influence of H2SO4 (sulfuric acid) as a catalyst at a high temperature of 180 °C, the hydroxyl group (-OH) of ethyl alcohol reacts with the acid to form a water molecule (H2O). This process of water elimination from the alcohol molecule is commonly known as dehydration.
The reaction can be represented by the following chemical equation:
C2H5OH + H2SO4 → C2H4 + H2O
As a result of this reaction, ethyl alcohol undergoes dehydrogenation, where it loses a hydrogen atom along with the hydroxyl group to form ethylene gas (C2H4). Ethylene is an unsaturated hydrocarbon and is commonly used in various industries, including the production of plastics, solvents, and synthetic fibers.
The presence of H2SO4 as a catalyst accelerates the rate of the reaction by providing an alternative reaction pathway with lower activation energy. The catalyst facilitates the breaking of the C-O bond in the alcohol, allowing for the formation of the ethylene molecule. The sulfuric acid does not undergo any permanent change during the reaction and can be reused.
Learn more about Dehydration
brainly.com/question/28428859
#SPJ11
With an aid of a diagram, Discuss the conditions of equilibrium for the following: 1. Floating body 2. Submerged body
Floating and submerged bodies require equal weight, buoyant force, and gravity forces to maintain equilibrium. Both require the center of gravity beneath the center of buoyancy.
1. Floating body: When an object floats in a fluid, there are three conditions for equilibrium: the weight of the floating object, the buoyant force, and the force of gravity acting on the object. The weight of the floating object must equal the buoyant force to keep the object floating, and the center of gravity must be beneath the center of buoyancy.The diagram below illustrates the conditions of equilibrium for a floating body:
2. Submerged body:When a body is submerged in a fluid, the forces of gravity and buoyancy act on the object to keep it in equilibrium. In order for an object to be in equilibrium, the weight of the object must be equal to the buoyant force, and the center of gravity must be at the center of buoyancy. The diagram below illustrates the conditions of equilibrium for a submerged body:
In summary, the conditions of equilibrium for a floating body and a submerged body are the same: the weight of the object must equal the buoyant force, and the center of gravity must be at the center of buoyancy.
To know more about buoyancy Visit:
https://brainly.com/question/30641396
#SPJ11
Solvents have a multi-purpose role in pharmaceutical processing and need to be chosen with care for the different processing steps of the active pharmaceutical ingredient (API), such as chemical reaction, separation and purification. In these processes, very often a reaction may take place in one solvent (S1) and the next processing step (e.g. another reaction, crystallisation, extraction or washing) may require a different solvent (S2) because the process performance is better than if using the original (S1). Solvent swap, or solvent exchange, is therefore a common and important task in API production within the pharmaceutical industry. The solvent swap task is the operation performed to remove an original solvent (S1) that is used in an earlier processing step and at the same time replace it with another solvent (S2) that is more suitable for the next processing step. The solvent swap task is performed as a separation task that is usually based on volatility difference, immiscibility difference or size difference. Batch distillation is often considered as the operation to perform the solvent swap. In the following, it is initially assumed that the solvent swap step will be followed by a crystallisation step for which the original solvent is not as suitable, for example, because the API would crystallise as needles/needle structures hampering the filtration process subsequent to crystallisation. Crystallisation steps are usually employed for the purification and recovery steps of the APIs, and the solvent selection will have an impact on the solid solubility and crystal structure. For the solvent swap, the swap solvent (S2) is somehow mixed with the original solvent (S1), which contains the API, which has been fed to the bottom of a regular batch distillation column. The original solvent is distilled off and collected as the top product whilst the swap solvent together with the API are collected in the still at the end and moved to the next processing step. For the downstream crystallisation process, one needs to make sure that S2 allows for the product recovery required. For example, cooling crystallisation requires a strong temperature dependence of the API solubility in S2. Special care needs to be taken, however, that the API does not crystallise prematurely during distillation.
1. Proper process control is as important for batch processing as it is for continuous manufacturing. Consider a solvent swap process where the original solvent (S1) and the swap solvent (S2) are pure solvents and propose an operating procedure and a control scheme for the regular batch distillation column when the objective is to keep a high production rate and safe operation, and where the process specification on allowable amount of original solvent remaining in the still is very low.
Assume also that the original solvent is to be recycled back to the reaction step, hence high purity is required.
Solvent swap, or solvent exchange, is a common and important task in pharmaceutical processing. It involves removing the original solvent used in one processing step and replacing it with a different solvent that is more suitable for the next step. This is typically done through batch distillation, where the original solvent is distilled off and collected as the top product, while the new solvent is collected with the active pharmaceutical ingredient (API) at the bottom. The solvent swap is performed to improve process performance and ensure the desired product recovery in downstream steps like crystallisation.
Solvent swap is crucial in pharmaceutical processing because different solvents may be required for different processing steps of the API. For example, a reaction may take place in one solvent, but the next step may require a different solvent for better performance. The solvent swap is performed as a separation task based on volatility difference, immiscibility difference, or size difference. Batch distillation is often used for this operation. In the case of downstream crystallisation, the choice of the swap solvent is important for the desired product recovery. Cooling crystallisation, for instance, requires a strong temperature dependence of the API solubility in the new solvent. Care must be taken to prevent premature crystallisation during distillation. Furthermore, since the original solvent is often recycled back to the reaction step, high purity is required.
Know more about distillation here:
https://brainly.com/question/31829945
#SPJ11
Let S be the upper half of the unit sphere x^2+y^2+z^2=1 and take n as the upper unit normal. Use Stoke's theorem to find ∬ S_[(∇×v)⋅n]dσ given v(x,y,z)=3z^2i+3xj−4y^3k. a) 3π b) −3π c)9π d)3/2π e) 6π
f) None of the above.
By using Stoke's theorem ∬ S [ (∇ × v) ⋅ n ] dσ is 6π. So, option e is the correct answer.
To apply Stoke's theorem and evaluate the surface integral, we need to calculate the curl of vector field v(x, y, z) and then find its dot product with the unit normal vector n.
Let's start by finding the curl of v(x, y, z):
∇ × v =
| i j k |
| ∂/∂x ∂/∂y ∂/∂z |
| 3z² 3x -4y³|
Applying the determinant expansion along the top row, we have:
∇ × v = (∂/∂y)(-4y³) - (∂/∂z)(3x) i
+ (∂/∂z)(3z²) - (∂/∂x)(-4y³) j
+ (∂/∂x)(3x) - (∂/∂y)(3z²) k
Simplifying, we get:
∇ × v = -12y² i + 3z² j + 3 k
Now, we need to find the dot product of ∇ × v with the unit normal vector n. Since the upper half of the unit sphere has positive z-component, the unit normal vector for this surface is n = (0, 0, 1).
Therefore, the dot product (∇ × v) ⋅ n simplifies to:
(-12y² i + 3z² j + 3 k) ⋅ (0, 0, 1)= 3
Now, we can evaluate the surface integral using Stoke's theorem:
∬ S [ (∇ × v) ⋅ n ] dσ = ∬ S (3) dσ
Since the surface S is the upper half of the unit sphere, the area element dσ can be written as dσ = r² sinθ dθ dφ, where r = 1 is the radius of the unit sphere, θ ranges from 0 to π/2, and φ ranges from 0 to 2π.
Therefore, the surface integral becomes:
∬ S (3) dσ = ∫∫ (3) r² sinθ dθ dφ
= 3 ∫[0 to 2π] ∫[0 to π/2] (1)² sinθ dθ dφ
= 3 ∫[0 to 2π] [-cosθ] [0 to π/2] dφ
= 3 ∫[0 to 2π] 1 dφ
= 3 (2π)
= 6π
Hence, the correct answer is e) 6π.
To know more about Stoke's theorem:
https://brainly.com/question/28381095
#SPJ11
To add two functions, you simply add the corresponding y-coordinates to get the combined function value. True False Question 2 (Mandatory) When two functions are added, the domain of the combined function consists of all of the values common to the domain of both of the original functions. True False Question 3 (Mandatory) When two functions are multiplied, the range of the combined function consists of all of the values in the range of both of the original functions. True False Question 4 (Mandatory) Given the cost function, C(n), and the revenue function, R(n), for a company, the profit function is given by P(n)=C(n)−R(n). True False
1: To add two functions, you simply add the corresponding y-coordinates to get the combined function value is false. 2: When two functions are added, the domain of the combined function consists of all of the values common to the domain of both of the original functions is True. 3: When two functions are multiplied, the range of the combined function consists of all of the values in the range of both of the original functions is False. 4: Given the cost function, C(n), and the revenue function, R(n), for a company, the profit function is given by P(n) = C(n) - R(n) is True.
1: To add two functions, you simply add the corresponding y-coordinates to get the combined function value.
False. To add two functions, you add the corresponding y-coordinates at each point, not the functions themselves.
2: When two functions are added, the domain of the combined function consists of all of the values common to the domain of both of the original functions.
True. When adding two functions, the resulting combined function will have a domain that includes all the values that are common to the domains of both original functions.
3: When two functions are multiplied, the range of the combined function consists of all of the values in the range of both of the original functions.
False. When multiplying two functions, the resulting combined function's range may not necessarily include all the values in the range of both original functions. The range of the combined function depends on the specific behavior of the functions being multiplied.
4: Given the cost function, C(n), and the revenue function, R(n), for a company, the profit function is given by P(n) = C(n) - R(n).
True. The profit function is typically defined as the difference between the revenue function and the cost function, where P(n) represents the profit at a given value n.
To know more about domain:
https://brainly.com/question/29155189
#SPJ4
Question 2 The Indigenous people perceive land as an economic asset to be exploited for economic gains. True False
Recognize and respect Indigenous perspectives on land, as they offer valuable insights into sustainable resource management and holistic approaches to development that prioritize the well-being of both people and the environment.
False. The statement that Indigenous people perceive land as an economic asset to be exploited for economic gains is not accurate and misrepresents the complex and diverse relationships that Indigenous communities have with their land. Indigenous perspectives on land are deeply rooted in cultural, spiritual, and ecological connections rather than solely economic considerations.
Indigenous peoples often view land as a sacred entity, an integral part of their identity, and a source of sustenance. Their relationship with the land is based on principles of stewardship, reciprocity, and harmony with nature. Traditional knowledge and practices passed down through generations emphasize sustainable resource management, biodiversity preservation, and the interconnectedness of all living beings.
While economic activities may be present within Indigenous communities, they are typically guided by principles of community well-being, self-sufficiency, and cultural preservation. Economic development is often pursued in ways that align with Indigenous values and prioritize the long-term health of the land and its inhabitants.
It is important to recognize and respect Indigenous perspectives on land, as they offer valuable insights into sustainable resource management and holistic approaches to development that prioritize the well-being of both people and the environment.
Learn more about valuable insights
https://brainly.com/question/27894163
#SPJ11
Directions: Complete the problem set, showing all work for problems below. 1. Calculate the molar concentration of a solution of a sample with 135 moles in 42.5 L of solution.
The molar concentration of a solution can be calculated by dividing the number of moles of solute by the total volume of the solution in liters.
The molar concentration of a solution of a sample with 135 moles in 42.5 L of solution can be calculated as follows:
To find the molar concentration of a solution, the formula is used;
Molarity (M) = Moles of solute (n) / Volume of solution (V)Molarity (M)
= 135 moles / 42.5 L
= 3.176 M (Answer)
Molarity is expressed in terms of moles of solute per liter of solution.
This means that the number of moles of solute is divided by the total volume of the solution in liters (L). For example, if a solution contains 1 mole of solute in 1 liter of solution, its molar concentration would be 1 M.
This is a common unit used in chemistry to express the concentration of solutions.
To know more about molar concentration visit:-
https://brainly.com/question/21841645
#SPJ11
Answer:
The molar concentration of the solution is 3.18 moles/L.
Step-by-step explanation:
To calculate the molar concentration of a solution, we use the formula:
Molar concentration (C) = moles of solute / volume of solution (in liters)
Given:
Moles of solute = 135 moles
Volume of solution = 42.5 L
Substituting the values into the formula:
C = 135 moles / 42.5 L
C = 3.18 moles/L
To know more about solution
https://brainly.in/question/56263721
#SPJ11
QUESTION 7: Consider the function f(x)=x3−4x+1 a) Find the interval(s) in which the function f(x) is increasing and the interval(s) in which the function is decreasing. b) Find the interval(s) in which the function f(x) is concave up and the interval(s) in which the function is concave down. c) Sketch the graph of the function f(x)
The function f(x) is increasing on the interval (-2/√3, 2/√3) and decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞).The given function is [tex]f(x) = x^3 - 4x + 1.[/tex].
a) To find the intervals where the function is increasing or decreasing, we need to determine where the derivative of the function is positive or negative. The derivative of [tex]f(x) is f'(x) = 3x^2 - 4[/tex].
To find the critical points, we set f'(x) = 0 and solve for x:
[tex]3x^2 - 4 = 0[/tex]
[tex]3x^2 = 4[/tex]
[tex]x^2 = 4/3[/tex]
x = ± √(4/3)
x = ± 2/√3
We have two critical points: x = -2/√3 and x = 2/√3.
Now, we can test the intervals between these critical points and beyond to determine where the function is increasing or decreasing.
For x < -2/√3, f'(x) < 0, so the function is decreasing.
For -2/√3 < x < 2/√3, f'(x) > 0, so the function is increasing.
For x > 2/√3, f'(x) < 0, so the function is decreasing.
Therefore, the function f(x) is increasing on the interval (-2/√3, 2/√3) and decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞).
b) To find the intervals where the function is concave up or concave down, we need to determine where the second derivative of the function is positive or negative. The second derivative of f(x) is f''(x) = 6x.
Since the second derivative is always positive (6x > 0), the function is concave up for all x.
c) To sketch the graph of the function, we can use the information we found in parts a) and b). The graph will be increasing on the interval (-2/√3, 2/√3), decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞), and concave up for all x. We can also plot the critical points at x = -2/√3 and x = 2/√3.
Please note that the sketch may vary based on the scale and accuracy of the graph.
To know more about derivative visit:
https://brainly.com/question/25324584
#SPJ11
The CO concentration in a stack is 345 ppm, the stack diameter is 24 inches, and the stack gas velocity is 11 ft/sec. The gas temperature and pressure are 355°F and 1 atm. Determine the CO mass emission rate in kg/day. Please show all steps
CO concentration in stack = 345 ppmStack diameter = 24 inchesStack gas velocity = 11 ft/secGas temperature = 355°F and Pressure = 1 atmWe need to find the CO mass emission rate in kg/day.
= πD²/4Given Diameter
= 24 inches = 2 ftSo, A
= π(2/2)²/4 = 0.306 ft
²Q = A × VQ = 0.306 × 11
= 3.366 ft³/s
Convert flow rate to m³/s3.366 ft³/s × 0.02832 = 0.0953 m³/s
= Molecular weight of CO
= 28So,CO = 345 × 0.0953 × 28 / 24.45
= 0.115 kg/s0.115 × 3600 × 24
= 9936 kg/day.
So, the CO mass emission rate in kg/day is 9936 kg/day.
To know more about diameter visit:
https://brainly.com/question/30862855
#SPJ11
The CO concentration in a stack is 345 ppm, the stack diameter is 24 inches, and the stack gas velocity is 11 ft/sec. The gas temperature and pressure are 355°F and 1 atm. The CO mass emission rate in kg/day is 9936 kg/day.
CO concentration in stack = 345 ppm
Stack diameter = 24 inches
Stack gas velocity = 11 ft/sec
Gas temperature = 355°F and Pressure = 1 atm
We need to find the CO mass emission rate in kg/day.
= πD²/4
Given Diameter
= 24 inches
= 2 ft
So, A = π(2/2)²/4
= 0.306 ft
²Q = A × VQ = 0.306 × 11
= 3.366 ft³/s
Convert flow rate to m³/s3.366 ft³/s × 0.02832
= 0.0953 m³/s
= Molecular weight of CO
= 28So,CO
= 345 × 0.0953 × 28 / 24.45
= 0.115 kg/s0.115 × 3600 × 24
= 9936 kg/day.
So, the CO mass emission rate in kg/day is 9936 kg/day.
To know more about diameter visit:
brainly.com/question/30862855
#SPJ11
You borrow $ 30,000 with an interest rate at 15% per year and will pay off the loan in three equal annual
payments, with the first payment occurring at the end of first year after the loan is made. The three equal
annual payments will be $13,139.40. Which of the following is true for your first payment at EOY 1?
a. Interest = $ 0; principal = $ 13,139.40
b. Interest = $ 13,139.40; principal = $0
c. Interest = $4,500; principal = $8,639.40
d. Interest = $4,500; principal = $13,139.40
The true statement about the first payment is Interest = $4,500; principal = $8,639.40
The correct answer choice is option C.
Which of the following is true for your first payment at EOY 1?Amount borrowed = $30,000
Interest rate = 15%
Annual payments = $13,139.40
Number of years = 3
Total payments at the end of 3 years = Annual payments × 3
= $39,418.20
Therefore,
Interest = $4,500;
principal = $8,639.40
Total = $13, 139.40 per year
Read more on loan:
https://brainly.com/question/26011426
#SPJ4
Cathy placed $6000 into a savings account. For how long can $900 be withdrawn from the account at the end of every month starting one month from now if it is 4.87% compounded monthly? The $900 can be withdrawn for ________months
$900 can be withdrawn from the account for approximately 35 months.
To determine how long $900 can be withdrawn from the savings account, we need to find the number of months it takes for the account balance to reach $900 after monthly compounding.
First, let's calculate the monthly interest rate. The annual interest rate is given as 4.87%. To convert it into a monthly interest rate, we divide it by 12 (months in a year).
Monthly interest rate = (4.87% / 100) / 12 = 0.04058
Next, we'll use the future value formula for compound interest:
[tex]FV = P * (1 + r)^n\\[/tex]
Where:
FV = Future Value (desired amount of $900)
P = Principal (initial deposit of $6000)
r = Monthly interest rate (0.04058)
n = Number of months
Now we can plug in the values and solve for n:
[tex]900 = 6000 * (1 + 0.04058)^nDivide both sides by 6000:0.15 = 1.04058^nTaking the natural logarithm (ln) of both sides:ln(0.15) = ln(1.04058^n)Using the logarithm properties (ln(a^b) = b * ln(a)):ln(0.15) = n * ln(1.04058)Now we can solve for n by dividing both sides by ln(1.04058):n = ln(0.15) / ln(1.04058)[/tex]
Using a calculator, we find:
n ≈ 34.85
Since we can't have a fraction of a month, we round up to the nearest whole number.
Therefore, $900 can be withdrawn from the account for approximately 35 months.
To know more about value click-
http://brainly.com/question/843074
#SPJ11
The BOD: of a municipal wastewater is determined to be 168 mg/L at 15°C. The BOD rate constant, k is known to be 0.18 day at 15°C. Compute the BOD5 of the sample at 20°C. What would be the remainin
To calculate the BOD5 of the sample at 20°C, we need additional information about the BOD rate constant at that temperature. Without that information, we cannot provide a direct calculation or answer.
Biological Oxygen Demand (BOD) is a measure of the amount of dissolved oxygen consumed by microorganisms while decomposing organic matter in water. The BOD rate constant (k) determines the rate at which BOD decreases over time. To calculate the BOD5 (BOD after 5 days), we need the BOD rate constant at 20°C.
Assuming we have the BOD rate constant at 20°C, we can use the following formula to calculate BOD5 at 20°C:
BOD5(20°C) = BOD(15°C) * (k20 / k15)^(t5 - t15)
Where:
BOD5(20°C) is the BOD5 at 20°C,
BOD(15°C) is the initial BOD at 15°C (168 mg/L),
k20 is the BOD rate constant at 20°C,
k15 is the BOD rate constant at 15°C (0.18 day),
t5 is the duration in days (5 days), and
t15 is the duration in days at 15°C (assumed as 5 days).
Without the value for k20, we cannot calculate the BOD5 at 20°C or determine the remaining BOD.
To determine the BOD5 of the sample at 20°C and the remaining BOD, we need the BOD rate constant at 20°C. Once we have that information, we can use the provided formula to calculate the BOD5 at 20°C.
To know more about temperature visit:
https://brainly.com/question/27944554
#SPJ11
Part A A 500-ft curve, grades of g, - +2.50% and g=-3.00% VPI at station 96 +80 and elevation 845 26 ft stakeout at full stations List station elevations for an equal target parabolic curve for the data given the evallons in the Express your answers in feet to five significant figures separated by com 190 Advoc 7 it Elev Sun Rest AS
You can calculate the station elevations for the equal target parabolic curve based on the given data.
To calculate the station elevations for an equal target parabolic curve, we need to use the given data. Let's break down the information provided:
Curve length: 500 ft
Grades: g = -2.50% and
g = -3.00%
VPI (Vertical Point of Intersection): Station 96+80,
Elevation 845.26 ft
Stakeout at full stations
To determine the station elevations for the equal target parabolic curve, we'll start with the VPI station and elevation and then calculate the elevations at regular intervals along the curve.
VPI Station 96+80,
Elevation 845.26 ft
For the -2.50% grade:
Station 97+00: Elevation = 845.26 ft - 2.50% × 20 ft
= 845.26 ft - 0.50 ft
= 844.76 ft
Station 98+00: Elevation = 844.76 ft - 2.50% × 100 ft
= 844.76 ft - 2.50 ft
= 842.26 ft
Continue this calculation for the remaining stations on the curve.
For the -3.00% grade:
Station 97+00: Elevation = 845.26 ft - 3.00% × 20 ft
= 845.26 ft - 0.60 ft
= 844.66 ft
Station 98+00: Elevation = 844.66 ft - 3.00% × 100 ft
= 844.66 ft - 3.00 ft
= 841.66 ft
Continue this calculation for the remaining stations on the curve.
By following this process, you can calculate the station elevations for the equal target parabolic curve based on the given data.
To know more about parabolic curve visit:
https://brainly.com/question/34023822
#SPJ11
To create an equal target parabolic curve based on the given data, we need to calculate the station elevations. The given information includes a 500-ft curve, grades of g = -2.50% and g = -3.00%, a VPI (Vertical Point of Intersection) at station 96 with a +80 elevation, and a stakeout at full stations. We will use these details to determine the station elevations for the equal target parabolic curve.
To calculate the station elevations for the equal target parabolic curve, we will consider the given data. Firstly, we have a 500-ft curve, which means the length of the curve is 500 feet. The grade of the curve is provided as g = -2.50%, indicating a downward slope, and g = -3.00%, indicating a steeper downward slope.
Next, we have the Vertical Point of Intersection (VPI) at station 96, with an elevation of +80 feet. This VPI is the point where the vertical alignment of the existing curve intersects with the proposed equal target parabolic curve.
To determine the station elevations for the equal target parabolic curve, we will use the stakeout at full stations. This means that we need to determine the elevation at every full station along the curve.
To calculate the station elevations, we need to apply the parabolic formula that relates the horizontal distance (X) and the vertical distance (Y) from the VPI:
[tex]\[ Y = aX^2 + bX + c \][/tex]
In this equation, a, b, and c are coefficients that need to be determined. We can obtain these coefficients by solving a system of equations based on the given data. Once we have the coefficients, we can substitute the values of X (horizontal distance from the VPI) for each full station and calculate the corresponding Y values (elevation). Finally, we express the station elevations in feet to five significant figures, separated by commas, and provide the results.
To learn more about elevations refer:
https://brainly.com/question/12213332
#SPJ11
A converging-diverging nozzle is designed to produce an exit flow of air at M = 4.0 and 1.0 atm. The stagnation temperature is 50°C. Calculate the upstream stagnation pressure. Calculate the throat area and mass flow for an exit area of 6.5 cm2.
A converging-diverging nozzle is an important component of a jet engine that is responsible for accelerating hot gases out of the back of the engine to produce thrust. The pressure, temperature, and velocity of the gases passing through the nozzle are controlled by the design of the nozzle.
The nozzle's design ensures that the gas flows at a high velocity and generates a lot of thrust. The following steps are used to calculate the upstream stagnation pressure: Given, Exit Mach Number (M) = 4.0, Exit Pressure (Pe) = 1.0 atm, Stagnation Temperature (T0) = 50°C1. Calculate the exit velocity using the isentropic relation for Mach number: Since M = 4.0, the exit velocity is:
[tex]V_e = M_e × c_e.[/tex]
Where c_e is the speed of sound at the exit.For air at 50°C, c_e = 1090 m/s. Therefore,V_e
[tex]4.0 × 1090 = 4360 m/s2.[/tex]
Calculate the pressure at the throat using the isentropic relation for Mach number:At the throat, M_t = 1.0 (by definition).Using the isentropic relation, we can calculate the pressure at the throat:P_t = P_e / [(1 + γ-1)/2]^(γ/γ-1)where γ = 1.4 (for air). Therefore, P_t = 1.0 / [(1 + 0.4)/2]^(1.4/0.4). P_t = 1.19 atm3.
Calculate the upstream stagnation pressure using the isentropic relation for stagnation pressure: Using the isentropic relation, we can calculate the upstream stagnation pressure:
[tex]P0 = Pe / [(1 + γ-1)/2]^(γ/γ-1) × [1 + (γ-1)/2 × Me^2]^(γ/γ-1)[/tex]
where Me is the Mach number at the exit (which is given as 4.0)Therefore[tex],P0 = 1.0 / [(1 + 0.4)/2]^(1.4/0.4) × [1 + (0.4/2) × 4^2]^(1.4/0.4)P0 = 10.68 atm.[/tex]
Therefore, the upstream stagnation pressure is 10.68 atm. The formula for mass flow is: [tex]dm/dt = ρ * A * V.[/tex]
Where, dm/dt is mass flow, ρ is density, A is the cross-sectional area of the flow, and V is the velocity of the flow. Therefore, the mass flow for an exit area of 6.5 cm² can be calculated using the following steps: Given, Exit Area (Ae) = 6.5 cm²Density (ρ) can be calculated using the ideal gas law :P = ρRTwhere P is the pressure, R is the gas constant, and T is the temperature.
Therefore, [tex]ρ = P / RT[/tex]
[tex](1.0 atm) / (287 J/kg-K × (50 + 273) K) = 0.382 kg/m³[/tex]
The velocity at the exit was calculated in step 1 as[tex]V_e = 4360 m/s.[/tex]
The cross-sectional area at the throat can be calculated using the isentropic relation for Mach number, which is :[tex]A_t = A_e / [(1/M_e) * ((2 / (γ+1)) * (1 + (γ-1)/2 * M_e^2))^((γ+1)/(2(γ-1)))].[/tex]
Therefore,[tex]A_t = 6.5 cm² / [(1/4) * ((2 / 1.4+1) * (1 + (0.4-1)/2 * 4^2))^((1.4+1)/(2(1.4-1)))][/tex]
[tex]A_t = 0.595 cm²[/tex]
The mass flow rate can now be calculated using the formula for mass flow:[tex]dm/dt = ρ * A_t * V_t = 0.382 kg/m³ × (0.595 cm² × 10^-4 m²/cm²) × 480 m/s dm/dt = 0.0115 kg/s.[/tex] Therefore, the mass flow rate is 0.0115 kg/s.
Therefore, the upstream stagnation pressure is 10.68 atm, and the mass flow rate is 0.0115 kg/s.
learn more about velocity visit:
brainly.com/question/30559316
#SPJ11
For the nonhomogenous system, 2a−4b+5c=8
14b−7a+4c=−28
c+3a−6b=12
The solution to the nonhomogeneous system is a = 4, b = 0, and c = 0.
To solve the nonhomogeneous system of equations:
2a - 4b + 5c = 8
14b - 7a + 4c = -28
c + 3a - 6b = 12
Step 1: Rearrange the equations to put them in standard form:
2a - 4b + 5c = 8 ---> Equation 1
-7a + 14b + 4c = -28 ---> Equation 2
3a - 6b + c = 12 ---> Equation 3
Step 2: Use the method of substitution or elimination to solve the system. Let's use the elimination method:
Multiply Equation 1 by -7 and Equation 2 by 2:
-14a + 28b - 35c = -56 ---> Equation 4
-14a + 28b + 8c = -56 ---> Equation 5
Subtract Equation 4 from Equation 5 to eliminate the "a" terms:
0 + 0 - 43c = 0
-43c = 0
Since -43c = 0, c must be equal to 0.
Substitute c = 0 into Equation 1:
2a - 4b + 5(0) = 8
2a - 4b = 8
Multiply Equation 3 by 2:
6a - 12b + 2c = 24 ---> Equation 6
Substitute c = 0 into Equation 6:
6a - 12b + 2(0) = 24
6a - 12b = 24
Now we have two equations:
2a - 4b = 8 ---> Equation 7
6a - 12b = 24 ---> Equation 8
Divide Equation 8 by 6:
a - 2b = 4
Multiply Equation 7 by 3:
6a - 12b = 24
Subtract the new Equation 7 from Equation 8 to eliminate the "a" terms:
0 + 0 - 36b = 0
-36b = 0
Since -36b = 0, b must also be equal to 0.
Now, substitute b = 0 into Equation 7:
2a - 4(0) = 8
2a = 8
Divide both sides by 2:
a = 4
Learn more about nonhomogeneous system:
https://brainly.com/question/32263699
#SPJ11
A reverse osmosis plant is needed to be installed near a village where the drinking water demand is 3000 cubic meter per day. Feed water is extracted from underground at a pressure of 14 bars and sent to single stage reverse osmosis plant. RO element available in market can process up to 40 cubic meter per hr. and a single vessel can accommodate maximum 25 elements. Analysis of underground water of that area shows 3000 ppm salts, where the majority is NaCl. If health organization demands less than 700 ppm of TDS in drinking water, provide the following things.
1. Suggest the feed required for required flow rate of clean water
162.76 cubic meters per hour of feed water is required to produce 125 cubic meters per hour of clean water.
Feed Required for Required Flow Rate of Clean Water:
The daily water demand is 3000 cubic meters per day, and we can easily calculate the hourly water demand using the following formula:
H= 24Q
Where, H = Hourly Water Demand
Q = Daily Water Demand / 24H = 3000 / 24H = 125 cubic meters per hour
To produce 125 cubic meters per hour of clean water, we will need to supply a higher quantity of water because of the presence of salts. We'll use the following formula to determine the feed water quantity:
F = (Q / (1 - R))
Where,
F = Feed Water Required
Q = Clean Water Required
R = % Recovery
We must first determine the % Recovery.
We can use the following formula to do so:
% Recovery = 100 - % Rejection
We are told that the TDS of the feed water is 3000 ppm and that the drinking water should have less than 700 ppm of TDS. As a result, the % Rejection can be calculated using the following formula:
% Rejection = (3000 - 700) / 3000 * 100
% Rejection = 76.67%
% Recovery = 100 - 76.67% = 23.33%
We can now calculate the Feed Water Required using the formula:
F = (125 / (1 - 0.2333))F = 162.76 cubic meters per hour
Therefore, 162.76 cubic meters per hour of feed water is required to produce 125 cubic meters per hour of clean water.
To know more about flow rate, click here
https://brainly.com/question/19863408
#SPJ11