By using the concept of energy, the final velocity of the particle is obtained approximately as 4.548 m/s.
To determine the final velocity of the particle using the concept of energy, we can apply the work-energy principle.
The work done on an object is equal to the change in its kinetic energy.
The work done on the particle is given by the formula:
Work = Force * Distance * cos(θ)
In this case, the force is 5.86 N and the distance is 0.227 m.
Since the angle θ is not provided, we will assume that the force is applied in the direction of motion, so cos(θ) = 1.
Work = 5.86 N * 0.227 m * 1 = 1.33162 N·m
The work done on the particle is equal to the change in its kinetic energy.
The initial kinetic energy is given by:
Initial Kinetic Energy = (1/2) * mass * initial velocity^2
Initial Kinetic Energy = (1/2) * 0.199 kg * (2.72 m/s)^2
Initial Kinetic Energy = 0.7319296 J
The final kinetic energy is given by:
Final Kinetic Energy = Initial Kinetic Energy + Work
Final Kinetic Energy = 0.7319296 J + 1.33162 N·m
Final Kinetic Energy = 2.0635496 J
Finally, we can determine the final velocity using the equation:
Final Kinetic Energy = (1/2) * mass * final velocity^2
2.0635496 J = (1/2) * 0.199 kg * final velocity^2
[tex](final \,velocity)^2[/tex] = 2.0635496 J / (0.199 kg * (1/2))
[tex](final \,velocity)^2[/tex] = 20.718592 J/kg
final velocity = [tex]\sqrt{20.718592 J/kg}[/tex] = 4.548 m/s
Therefore, the final velocity of the particle is approximately 4.548 m/s.
Learn more about energy here:
https://brainly.com/question/3347851
#SPJ11
. Using the image below as an aid, describe the energy conversions a spring undergoes during simple harmonic motion as it moves from the point of maximum compression to maximum stretch in a frictionless environment. Be sure to indicate the points at which there will be i. maximum speed. ii. minimum speed. iii, minimum acceleration.
As the spring moves from the point of maximum compression to maximum stretch in a frictionless environment, the following energy conversions take place:The spring’s elastic potential energy is converted to kinetic energy, which is maximum when the spring passes through the equilibrium position.
This implies that the point at which the spring has maximum speed is the equilibrium position (point C).As the spring is released from its compressed position, it moves towards the equilibrium position, slowing down and coming to a halt momentarily.
Since the kinetic energy is converted back to elastic potential energy, the point at which the spring has minimum speed is the two extreme positions at maximum compression (point A) and maximum stretch (point E).The restoring force acting on the spring is maximum at the extreme positions (points A and E), implying that the acceleration is maximum at these positions. Therefore, the point at which the spring has minimum acceleration is the equilibrium position (point C).
Therefore, in the given diagram, the points of maximum speed, minimum speed, and minimum acceleration are represented as:Maximum speed - Point CMinimum speed - Points A and EMinimum acceleration - Point C.
Learn more on acceleration here:
brainly.in/question/9415862
#SPJ11
What is the magnetic field strength created at its center in T ?
The magnetic field strength created at the center of a circular loop carrying a current of 30.0 A and consisting of 250 turns with a radius of 10.0 cm is approximately 3.8 × 10^(-3) T (tesla).
The magnetic field strength at the center of a circular loop carrying current can be calculated using the formula: B = (μ₀ * I * N) / (2 * R), where B is the magnetic field strength, μ₀ is the permeability of free space (approximately 4π × 10^(-7) T·m/A), I is the current, N is the number of turns in the loop, and R is the radius of the loop.
Substituting the given values, we have:
B = (4π × 10^(-7) T·m/A * 30.0 A * 250) / (2 * 0.10 m)
B ≈ 3.8 × 10^(-3) T
Therefore, the magnetic field strength created at the center of the circular loop is approximately 3.8 × 10^(-3) T (tesla).
Learn more about magnetic field here:
https://brainly.com/question/19542022
#SPJ11
The complete question is:
Inside a motor, 30.0 A passes through a 250 -turn circular loop that is 10.0 cm in radius. What is the magnetic field strength created at its center?
The A string on a violin has a fundamental frequency of a40 Hz. The length of the vibrating portion is 30.4 cm and has a mass of 0.342 g. Under what tension must the string be placed?
Answer: The tension in the A string of the violin must be placed under 263.7 N of tension.
The A string on a violin has a fundamental frequency of a 440 Hz.
To find the tension (T) in a string: T = (m * v²) / L
Where: m = the mass of the string, L = the length of the vibrating portion, v = the speed of the wave. The speed of the wave is given by the formula: v = √(T/μ)
Where T is the tension in the string and μ is the linear density of the string. To calculate the linear density of the string, we use the formula: μ = m/L
Fundamental frequency, f = 440 Hz
Length of the vibrating portion, L = 30.4 cm = 0.304 m
Mass of the string, m = 0.342 g = 0.000342 kg.
Using the frequency and the length of the vibrating portion, we can find the speed of the wave:
v = f * λλ
= 2L = 2(0.304 m)
= 0.608 mv
= (440 Hz)(0.608 m)
= 267.52 m/s.
Now, we can find the tension in the string:
T = (m * v²) / L
T = (0.000342 kg * (267.52 m/s)²) / 0.304 m
T ≈ 263.7 N.
Therefore, the tension in the A string of the violin must be placed under 263.7 N of tension.
Learn more about tension: https://brainly.com/question/24994188
#SPJ11
Elon Bezos launches two satellites of different masses to orbit the Earth circularly on the same radius. The lighter satellite moves twice as fast as the heavier one. Your answer NASA astronauts, Kjell Lindgren, Pilot Bob Hines, Jessica Watkins, and Samantha Cristoforetti, are currently in the International Space Station, and experience apparent weightlessness because they and the station are always in free fall towards the center of the Earth. Your answer True or False Patrick pushes a heavy refrigerator down the Barrens at a constant velocity. Of the four forces (friction, gravity, normal force, and pushing force) acting on the bicycle, the greatest amount of work is exerted by his pushing force. Your answer One of the 79 moons of Jupiter is named Callisto. The pull of Callisto on * 2 points Jupiter is greater than that of Jupiter on Callisto.
1. True - Astronauts in the International Space Station experience apparent weightlessness because they and the station are always in free fall towards the center of the Earth.
2. False - The pushing force exerted by Patrick does not do the greatest amount of work when he pushes a heavy refrigerator at a constant velocity.
3. False - The pull of Callisto on Jupiter is not greater than that of Jupiter on Callisto.
1. True - Astronauts in the International Space Station (ISS) experience apparent weightlessness because they and the station are in a state of continuous free fall around the Earth. They are constantly accelerating towards the Earth's center due to gravity, creating the sensation of weightlessness.
2. False - When Patrick pushes a heavy refrigerator at a constant velocity, the work done by the pushing force is zero because the displacement of the refrigerator is perpendicular to the force. The force of gravity, friction, and the normal force exerted by the ground contribute to the work done in balancing the forces and maintaining a constant velocity.
3. False - According to Newton's third law of motion, the gravitational force between two objects is equal and opposite. The pull of Callisto on Jupiter is equal in magnitude to the pull of Jupiter on Callisto, as governed by the law of universal gravitation.
Learn more about gravitational force here:
https://brainly.com/question/32609171
#SPJ11
For the systems whose closed loop transfer functions are given below, determine whether the system is stable, marginally stable or unstable. -5s +3 2s-1 a) T₁(s)=- 2s +1 (s+1)(s²-3s+2)' ; b) T₂ (s)=- (5+1)(s² + s +1)* ) ₂ (s) = (s-2)(s² +s+1)' 2s+1 d) T₁ (s)=- ; e) T,(s) = (s+1)(s² +1)' f)T(s)=- s+5 (s+3)(x²+4)² s-1 s(s² + s +1)
We aim to prove that the functions f(x) and x*f(x) are linearly independent for any non-constant function f(x). Linear independence means that no non-trivial linear combination of the two functions can result in the zero function.
By assuming the existence of constants a and b, we will demonstrate that the only solution to the equation a*f(x) + b*(x*f(x)) = 0 is a = b = 0. To begin, let's consider the linear combination a*f(x) + b*(x*f(x)) = 0, where a and b are constants. We want to show that the only solution to this equation is a = b = 0.
Expanding the expression, we have a*f(x) + b*(x*f(x)) = (a + b*x)*f(x) = 0. Since f(x) is a non-constant function, there exists at least one value of x (let's call it x0) for which f(x0) ≠ 0.Plugging in x = x0, we obtain (a + b*x0)*f(x0) = 0. Since f(x0) ≠ 0, we can divide both sides of the equation by f(x0), resulting in a + b*x0 = 0.
Now, notice that this linear equation holds for all x, not just x0. Therefore, a + b*x = 0 is true for all x. Since the equation is linear, it must hold for at least two distinct values of x. Let's consider x1 ≠ x0. Plugging in x = x1, we have a + b*x1 = 0.Subtracting the equation a + b*x0 = 0 from the equation a + b*x1 = 0, we get b*(x1 - x0) = 0. Since x1 ≠ x0, we have (x1 - x0) ≠ 0. Therefore, b must be equal to 0.
With b = 0, we can substitute it back into the equation a + b*x0 = 0, giving us a + 0*x0 = 0. This simplifies to a = 0. Hence, we have shown that the only solution to the equation a*f(x) + b*(x*f(x)) = 0 is a = b = 0. Therefore, the functions f(x) and x*f(x) are linearly independent for any non-constant function f(x).In conclusion, the functions f(x) and x*f(x) are linearly independent because their only possible linear combination resulting in the zero function is when both the coefficients a and b are equal to zero.
Learn more about coefficients here:- brainly.com/question/1594145
#SPJ11
What is the magnitude of the initial angular momentum of the system? ∣Li∣= _______ kg m²/s
The magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
What is angular momentum?
Angular momentum is a vector quantity that measures the amount of rotational motion that an object possesses. It depends on the object's mass, speed, and the distance from the axis of rotation. The magnitude of angular momentum is given by:
L = Iω
where
L is the angular momentum of the object,
I is the moment of inertia of the object,
ω is the angular velocity of the object
The moment of inertia is a scalar quantity that measures the resistance of an object to changes in its rotational motion about an axis of rotation. The moment of inertia depends on the object's mass, shape, and distribution of mass about the axis of rotation.
Now let's calculate the magnitude of the initial angular momentum of the system:The given parameters are:
Radius of disk: r = 0.2 m
Mass of disk: m = 3.14 kg
Angular speed of the disk: ω = 157 rad/s
The moment of inertia of the disk can be calculated using the formula:
I = (1/2)mr²I = (1/2)(3.14)(0.2)²
I = 0.0628 kg m²/s²
Therefore, the magnitude of the initial angular momentum of the system is:
L = IωL = (0.0628)(157)
L = 9.8584 kg m²/s
Therefore, the magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
Learn more about angular momentum:
https://brainly.com/question/4126751
#SPJ11
A 0.480-kg pendulum bob passes through the lowest part of its path at a speed of 7.46 m/s. (a) What he the magnitude of the tension in the pendulum cable at this point if the pendulum is 79.0 cm lang? N (b) When the pendolum feaches its highest point, what angle does the cable make with the vertical? (Enter your answer to at least ane decimat phace.) (c) What is the magnitude of the tertion in the pendulum cable when the pendulum reaches its highest point? P
(a) Mv²/2 = mgh where v = 7.46 m/s, m = 0.480 kg, g = 9.81 m/s²,h = 0.79 m. (b) Thus, sinθ = opposite/hypotenuse = 0.79/h , Hypotenuse = length of the pendulum = 0.79 m. (c) Thus, the magnitude of the tension in the pendulum cable is 4.71 N
a) Magnitude of tension in the pendulum cable: 56.58 N When the pendulum bob is at its lowest point, all its energy will be in the form of kinetic energy.
Thus, it can be stated that KE + PE = constant.
Here, PE is zero as there is no height, and thus the total energy of the system is equal to the kinetic energy of the pendulum bob.Mv²/2 = mgh wherev = 7.46 m/s, m = 0.480 kg,g = 9.81 m/s²,h = 0.79 m
By substituting these values in the above formula, we get: Tension in the pendulum cable is equal to weight component in the direction of the cable, which is given by: mg cosθ
Here,θ is the angle the cable makes with the vertical.
b) The angle that the cable makes with the vertical is: 64.67°When the pendulum bob is at its highest point, all its energy will be in the form of potential energy.
Thus, it can be stated that KE + PE = constant.
Here, KE is zero as there is no motion, and thus the total energy of the system is equal to the potential energy of the pendulum bob. mgh = mgh wherev = 0 m/s,m = 0.480 kg, g = 9.81 m/s²,h = 0.79 m
Thus, sinθ = opposite/hypotenuse = 0.79/h , Hypotenuse = length of the pendulum = 0.79 m
c) Magnitude of tension in the pendulum cable: 4.59 N
At the highest point, the tension in the cable is equal to the weight of the bob, which is given by:mg = 0.480 × 9.81 = 4.7068 N
Thus, the magnitude of the tension in the pendulum cable is 4.71 N (rounded off to two decimal places).
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Write True if the statement is correct, but if it's False, change the underlined word
or group of words to make the whole statement true. Write your answer on the space
provided before the number.
1. Heat engine is a device that converts thermal energy into mecha
work.
2. Doing mechanical work on the system will decrease its internal energy.
3. Internal energy is proportional to the change in temperature.
4. Only heat contributes to the total internal energy of the system.
5. Internal energy stored in the body is in the form of fats.
6. Heat can be completely transformed into work.
7. If the amount of work done (W) is the same as the amount of energy
transferred in by heat (Q), the net change in internal energy is 1.
8. The temperature of the system increases when work is done on the
system.
1. True. A heat engine is a device that converts thermal energy into mecha work.
2. False. Doing mechanical work on the system will increase or decrease its internal energy.
3. False. Internal energy is not directly proportional to the change in temperature.
4. False. Both heat and work can contribute to the total internal energy of the system.
5. False. Internal energy stored in the body is in the form of various energy sources.
6. False. Heat cannot be completely transformed into work without any losses.
7. False. If the amount of work done (W) is the same as the amount of energy transferred in by heat (Q), the net change in internal energy is zero.
8. False. The temperature of the system may increase or decrease when work is done on the system.
1. A heat engine is a device that converts thermal energy into mecha work.
2. False. Doing mechanical work on the system can either increase or decrease its internal energy, depending on the specific circumstances.
3. False. Internal energy is not directly proportional to the change in temperature. It depends on various factors such as pressure, volume, and the type of substance. The change in internal energy can be influenced by multiple factors, not just temperature.
4. False. Both heat and work can contribute to the total internal energy of the system. Internal energy is the sum of the system's kinetic energy and potential energy, which can be affected by both heat and work interactions.
5. False. Internal energy stored in the body is not solely in the form of fats. It includes various forms of energy, including chemical energy from nutrients, thermal energy, and other forms.
6. False. Heat cannot be completely transformed into work without any losses according to the laws of thermodynamics. There will always be some inefficiencies and losses in the conversion process.
7. False. If the amount of work done (W) is the same as the amount of energy transferred in by heat (Q), the net change in internal energy is zero according to the first law of thermodynamics, not 1.
8. False. The temperature of the system can increase or decrease when work is done on the system, depending on various factors such as the type of work done, the properties of the system, and the specific conditions.
know more about kinetic energy here:
https://brainly.com/question/30337295
#SPJ8
A 1900 kg car accelerates from 12 m/s to 20 m/s in 9 s. The net force acting on the car is:
The 1900 kg car accelerates from 12 m/s to 20 m/s in 9 seconds. We need to determine the net force acting on the car is 1691 N.
To find the net force acting on the car, we can use Newton's second law of motion, which states that the net force on an object is equal to the object's mass multiplied by its acceleration
[tex](F_net = m * a)[/tex]
First, we calculate the acceleration of the car using the equation
[tex]a = (v_f - v_i) / t[/tex]
where v_f is the final velocity, v_i is the initial velocity, and t is the time taken. Plugging in the given values, we have
[tex]a = (20 m/s - 12 m/s) / 9 s = 0.89 m/s^2.[/tex]
Next, we can calculate the net force by multiplying the mass of the car by its acceleration:
[tex]F_net = 1900 kg * 0.89 m/s^2 = 1691 N.[/tex]
To learn more about acceleration
brainly.com/question/2303856
#SPJ11
In a photoelectric effect experiment, if the frequency of the photons are increased while the intensity of the photons are held the same. the work function increases. the maximum kinetic energy of the photoelectrons increases. the maximum current increases. the stopping potential decreases.
The correct option is b. Increasing the frequency of photons in a photoelectric effect experiment while keeping the intensity constant will result in an increase in the maximum kinetic energy of the photoelectrons.
The photoelectric effect refers to the emission of electrons from a material when it is exposed to light. The energy of the emitted electrons is determined by the frequency of the photons that strike the material.
According to the equation E = hf, where E is the energy of a photon, h is Planck's constant, and f is the frequency of the photon, increasing the frequency of photons will lead to an increase in the energy of the individual photons. Therefore, when the frequency is increased while the intensity (number of photons per second) remains constant, the average energy of the photons increases.
The maximum kinetic energy of the photoelectrons depends on the energy of the incident photons and the work function of the material, which is the minimum energy required for an electron to be emitted. As the frequency of the photons increases, the energy of the photons increases, resulting in a higher maximum kinetic energy for the emitted electrons. Therefore, the correct option is b) the maximum kinetic energy of the photoelectrons increases.
Learn more about Planck's constant here:
https://brainly.com/question/2289138
#SPJ11
The complete question is:
In a photoelectric effect experiment, if the frequency of the photons is increased while the intensity of the photons is held the same. Choose the option which is best suitable
a)the work function increases.
b)the maximum kinetic energy of the photoelectrons increases.
c)the maximum current increases.
d)the stopping potential decreases.
A buzzer attached cart produces the sound of 620 Hz and is placed on a moving platform. Ali and Bertha are positioned at opposite ends of the cart track. The platform moves toward Ali while away from Bertha. Ali and Bertha hear the sound with frequencies f₁ and f2, respectively. Choose the correct statement. A. (f₁f2) > 620 Hz B. fi > 620 Hz > f₂ C. f2> 620 Hz > f₁
Ali hears a higher frequency than the emitted frequency (620 Hz) and Bertha hears a lower frequency than the emitted frequency, the correct statement is C. f₂ > 620 Hz > f₁.
When a sound source is moving towards an observer, the frequency of the sound heard by the observer is higher than the actual frequency emitted by the source. This phenomenon is known as the Doppler effect. Conversely, when a sound source is moving away from an observer, the frequency of the sound heard is lower than the actual frequency emitted.
In this scenario, as the buzzer attached to the cart is placed on a moving platform and is approaching Ali while moving away from Bertha, Ali will hear a higher frequency f₁ compared to the emitted frequency of 620 Hz. On the other hand, Bertha will hear a lower frequency f₂ compared to the emitted frequency of 620 Hz.
Learn more about frequency here:
https://brainly.com/question/2140860
#SPJ11
The position vector of a particle of mass 2.20 kg as a function of time is given by ř = (6.00 i + 5.40 tſ), whereř is in meters and t is in seconds. Determine the angular momentum of the particle about the origin as a function of time. k) kg · m²/s
The angular momentum of the particle about the origin as a function of time is L = (32.40)k kg · m²/s. The angular momentum does not depend on time and remains constant throughout the motion.
The angular momentum of a particle about the origin is given by L = m(ř × v), where m is the mass of the particle, ř is the position vector, and v is the velocity vector. To calculate the angular momentum as a function of time, we need to find the time derivative of the position vector and the velocity vector.
Given that ř = (6.00 i + 5.40 t), the velocity vector v is the derivative of ř with respect to time: v = dř/dt = (0 + 5.40) i = 5.40 i m/s.
Now we can calculate the cross product of ř and v. The cross product of two vectors in three dimensions is given by the formula (a × b) = (a_yb_z - a_zb_y)i + (a_zb_x - a_xb_z)j + (a_xb_y - a_yb_x)k. In this case, since both vectors ř and v have only i-components, the cross product simplifies to L = m(0 - 0)i + (0 - 0)j + (6.00 * 5.40 - 0)k = (0)i + (0)j + (32.40)k.
Learn more about angular momentum here:
https://brainly.com/question/29563080
#SPJ11
The following two questions are based on having a proton as a source charge. a) Find the potential at a distance of 1.00 cm from a proton. b) What is the potential DIFFERENCE between two points that are 1.00 cm and 2.00 cm from a proton? The following two questions are based on having an electron as a source charge. a) Find the potential at a distance of 1.00 cm from an electron. b) What is the potential DIFFERENCE between two points that are 1.00 cm and 2.00 cm from an electron?
The potential at a distance of 1.00 cm from a proton is 9.0 × [tex]10^{3}[/tex] volts, and the potential difference between two points that are 1.00 cm and 2.00 cm from a proton is 4.5 ×[tex]10^{3}[/tex] volts.
The potential at a distance of 1.00 cm from an electron is -9.0 × [tex]10^{3}[/tex] volts, and the potential difference between two points that are 1.00 cm and 2.00 cm from an electron is -4.5 × [tex]10^{3}[/tex]volts.
a) The potential at a distance r from a proton can be calculated using the formula V = k*q/r, where V is the potential, k is the Coulomb's constant (8.99 × [tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]), and q is the charge of the proton (1.6 × [tex]10^{-19}[/tex]C). Plugging in the values, we get V = (8.99 × [tex]10^{9}[/tex][tex]Nm^2/C^2[/tex]) * (1.6 × [tex]10^{-19}[/tex] C) / (0.01 m) = 9.0 × [tex]10^{3}[/tex] volts.
b) The potential difference between two points can be calculated by subtracting the potentials at those points. In this case, the potential difference between two points that are 1.00 cm and 2.00 cm from a proton can be found by subtracting the potential at 2.00 cm from the potential at 1.00 cm.
Using the same formula as before, we get ΔV = V2 - V1 = (8.99 × [tex]10^{9}[/tex][tex]Nm^2/C^2[/tex]) * (1.6 × [tex]10^{-19}[/tex] C) * (1 / 0.02 m - 1 / 0.01 m) = 4.5 × 10^3 volts.
For the electron, the signs of the potentials and potential differences are opposite due to the negative charge of the electron. Therefore, the potential at a distance of 1.00 cm from an electron is -9.0 × [tex]10^{3}[/tex] volts, and the potential difference between two points that are 1.00 cm and 2.00 cm from an electron is -4.5 × [tex]10^{3}[/tex] volts.
Learn more about distance here ;
https://brainly.com/question/11969946
#SPJ11
A 0.900 kg hammer is moving horizontally at 4.50 m/s when it strikes a nail and comes to rest after driving it 1.00 cm into a board. (a) Calculate the duration of the impact. X S (b) What was the average force exerted on the nail? N
The duration of the impact can be calculated by considering the work-energy theorem, while the average force exerted on the nail is calculated by dividing the change in momentum by the duration of the impact.
The hammer comes to a stop after driving the nail 1.00 cm into the board. This implies that it decelerated uniformly. We can use the equation of motion v^2 = u^2 - 2as to find the deceleration, where v is the final velocity (0 m/s), u is the initial velocity (4.50 m/s), a is the acceleration, and s is the distance (1.00 cm = 0.01 m). Solving for a, we get a = (v^2 - u^2) / -2s = -1012.5 m/s^2.
(a) The duration of the impact can be calculated using the equation t = (v - u) / a, resulting in t = -0.00444 seconds (4.44 ms).
(b) The average force exerted on the nail is equal to the change in momentum of the hammer divided by the time taken. The initial momentum is the mass of the hammer times its initial velocity (0.900 kg * 4.50 m/s = 4.05 kg.m/s). The final momentum is zero (as the hammer comes to rest). The change in momentum (Δp) is therefore -4.05 kg.m/s. The average force (F) can then be calculated by dividing this change in momentum by the time of impact, F = Δp / t, which results in -912 N.
Learn more about Newton's laws of motion here:
https://brainly.com/question/32165039
#SPJ11
Watching a car recede at 21 m/s, you notice that after 11 min the two taillights are no longer resolvable. If the diameter of your pupil is 5.0 mm in the dim ambient lighting, explain the reasoning for the steps that allow you to determine the spacing of the lights.
To determine the spacing of the taillights, you can use the concept of angular resolution. By considering the speed of the receding car, the time elapsed, the diameter of your pupil, and the distance traveled by the car, you can calculate the spacing between the taillights.
When observing a receding car, the spacing between its taillights can be determined by considering the concept of angular resolution. Angular resolution refers to the smallest angle at which two objects can be distinguished. In this scenario, you first convert the given time of 11 minutes to seconds (660 seconds) and calculate the distance traveled by the car during that time using its speed of 21 m/s (13,860 meters).
To determine the spacing between the taillights, you need to consider your line of sight. The diameter of your pupil, given as 5.0 mm, is converted to meters (0.005 meters). The angular resolution is then determined by dividing the diameter of your pupil by the distance between the taillights. By multiplying the angular resolution by the distance traveled by the car, you can calculate the spacing between the taillights. In this case, the spacing is equal to 0.005 meters.
Therefore, by following these steps and considering the relevant variables, you can determine the spacing between the taillights based on the concept of angular resolution and the given parameters.
Learn more about taillights here;
https://brainly.com/question/30472299
#SPJ11
One infinite and two semi-infinite wires carry currents with their directions and magnitudes shown. The wires cross but do not connect. What is the magnitude of the net magnetic field at the P? 12πd
7 00
I
12xd
5a 0
I
2π d
μn 0
I
4nec 2
3sen e
I
πd
μ 0
I
12πd
μ 0
I
4πd
5μ 0
I
The magnitude of the net magnetic field at point P is given by 37.2 x 10^(-7) I T.
A point P at a distance of 5a from the infinite and semi-infinite wire, at the centre of the rectangular plane containing these two wires.Both wires are carrying a current I.The magnitude of the net magnetic field at point P is to be determined.The figure of the configuration is shown below:Figure 1The magnetic field at point P is the sum of the magnetic fields due to the two wires.
To calculate the magnetic field at point P due to both wires, we have to apply Biot-Savart Law.Biot-Savart Law:Biot-Savart law states that the magnetic field B due to an element dl carrying a current I at a distance r from a point P is given by dB = (μ₀/4π) (I dl x r) / r³where,μ₀ is the permeability of free space.Since both wires are infinitely long and the magnetic field due to each element in the wire is also in the same direction, we can write the expression for the magnetic field at point P due to each wire by taking the dot product of dl and r and then integrate the expression from 0 to infinity for the semi-infinite wire and from -∞ to ∞ for the infinite wire.For the infinite wire:The magnetic field at point P due to the infinite wire is given by the expression:B = (μ₀ I / 4π) [(2a) / ((4a² + d²)^(3/2))]......
(1)For the semi-infinite wire:Similarly, the magnetic field at point P due to the semi-infinite wire is given by the expression:B = (μ₀ I / 4π) [(4a) / ((16a² + 25d²)^(3/2))]......(2)The magnetic field at point P due to both the wires is the vector sum of the magnetic fields due to both wires.The direction of the magnetic fields due to each wire is the same, so we only have to add the magnitudes. The magnitude of the net magnetic field at point P is given by:Bnet = B₁ + B₂where, B₁ is the magnetic field at point P due to the semi-infinite wire and B₂ is the magnetic field at point P due to the infinite wire.Bnet = (μ₀ I / 4π) [(4a) / ((16a² + 25d²)^(3/2))] + (μ₀ I / 4π) [(2a) / ((4a² + d²)^(3/2))]Bnet = (μ₀ I / 4π) [4a / ((16a² + 25d²)^(3/2)) + 2a / ((4a² + d²)^(3/2))]Bnet = (μ₀ I / 4π) [a / ((4a² + 5d²/4)^(3/2)) + a / ((a² + d²/4)^(3/2))]Bnet = (μ₀ I / 4π) [a / (4a² + 5d²/4)^(3/2)) + a / (a² + d²/4)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 5(d/2a)²)^(3/2)) + 1 / (1 + (d/2a)²)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 5(5/2)²)^(3/2)) + 1 / (1 + (5/2)²)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 25/4)^(3/2)) + 1 / (1 + 25/4)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (41/16)^(3/2)) + 1 / (29/4)^(3/2))]Bnet = (μ₀ I / 4πa) [(16/41)^(3/2) + (4/29)^(3/2))]Bnet = (μ₀ I / 4πa) [(16/41)^(3/2) + (4/29)^(3/2))]Bnet = (μ₀ I / 4πa) [0.162 + 0.127]Bnet = (μ₀ I / 4πa) (0.289)Bnet = (μ₀ I / 4πa) (17.6)Bnet = (μ₀ I / 4πa) [(4π * 10^(-7)) * 150 / a]Bnet = 37.2 x 10^(-7) I T. The magnitude of the net magnetic field at point P is given by 37.2 x 10^(-7) I T.
Learn more on this magnetic field here:
brainly.com/question/14848188
#SPJ11
An object of mass m is suspended from a spring whose elastic constant is k in a medium that opposes the motion with a force opposite and proportional to the velocity. Experimentally the frequency of the damped oscillation has been determined and found to be √3/2 times greater than if there were no damping.
Determine:
a) The equation of motion of the oscillation.
b) The natural frequency of oscillation
c) The damping constant as a function of k and m
The equation of motion of the oscillation is m * d^2x/dt^2 + (c/m) * dx/dt + k * x = 0.The natural frequency of oscillation is 4km - 3k - c^2 = 0.The damping constant is = ± √(4km - 3k)
a) To determine the equation of motion for the damped oscillation, we start with the general form of a damped harmonic oscillator:
m * d^2x/dt^2 + c * dx/dt + k * x = 0
where:
m is the mass of the object,
c is the damping constant,
k is the elastic constant of the spring,
x is the displacement of the object from its equilibrium position,
t is time.
To account for the fact that the medium opposes the motion with a force opposite and proportional to the velocity, we include the damping term with a force proportional to the velocity, which is -c * dx/dt. The negative sign indicates that the damping force opposes the motion.
Therefore, the equation of motion becomes:
m * d^2x/dt^2 + c * dx/dt + k * x = -c * dx/dt
Simplifying this equation gives:
m * d^2x/dt^2 + (c/m) * dx/dt + k * x = 0
b) The natural frequency of oscillation, ω₀, can be determined by comparing the given frequency of damped oscillation, f_damped, with the frequency of undamped oscillation, f_undamped.
The frequency of damped oscillation, f_damped, can be expressed as:
f_damped = (1 / (2π)) * √(k / m - (c / (2m))^2)
The frequency of undamped oscillation, f_undamped, can be expressed as:
f_undamped = (1 / (2π)) * √(k / m)
We are given that the frequency of damped oscillation, f_damped, is (√3/2) times greater than the frequency of undamped oscillation, f_undamped:
f_damped = (√3/2) * f_undamped
Substituting the expressions for f_damped and f_undamped:
(1 / (2π)) * √(k / m - (c / (2m))^2) = (√3/2) * (1 / (2π)) * √(k / m)
Squaring both sides and simplifying:
k / m - (c / (2m))^2 = (3/4) * k / m
k / m - (c / (2m))^2 - (3/4) * k / m = 0
Multiply through by 4m to clear the fractions:
4km - c^2 - 3k = 0
Rearranging the equation:
4km - 3k - c^2 = 0
We can solve this quadratic equation to find the relationship between c, k, and m.
c) The damping constant, c, as a function of k and m can be determined by solving the quadratic equation obtained in part (b). Rearranging the equation:
c^2 - 4km + 3k = 0
Using the quadratic formula:
c = ± √(4km - 3k)
Note that there are two possible solutions for c due to the ± sign.
Learn more about oscillation here ;
https://brainly.com/question/30111348
#SPJ11
Since the investigative question has two variables, you need to focus on each one separately. Thinking only about the first part of the question, mass, what might be a hypothesis that would illustrate the relationship between mass and kinetic energy? Use the format of "if…then…because…” when writing your hypothesis.
In order to form a hypothesis that would illustrate the relationship between mass and kinetic energy, we first need to understand what kinetic energy and mass are and how they are related. Kinetic energy is the energy that an object possesses due to its motion, and is given by the formula KE = 0.5mv², where m is the mass of the object and v is its velocity. Mass, on the other hand, is a measure of the amount of matter in an object.
The relationship between mass and kinetic energy is direct, meaning that as mass increases, so does kinetic energy, provided that velocity remains constant. Similarly, if velocity increases, then kinetic energy will increase as well, provided that mass remains constant.
The hypothesis that illustrates this relationship can be stated as follows:If the mass of an object is increased, then the kinetic energy of the object will also increase, because kinetic energy is directly proportional to mass, assuming velocity remains constant.In other words, if the mass of an object is doubled, then its kinetic energy will also double, assuming that its velocity remains constant. This hypothesis can be tested through experiments that involve measuring the kinetic energy of objects with different masses, but with the same velocity.
For more such questions on kinetic energy, click on:
https://brainly.com/question/8101588
#SPJ8
If the mass of an object increases, then its kinetic energy will increase proportionally because mass and kinetic energy have a linear relationship when graphed.
A force that varies with time F = 13t2-35t +79 acts on a sled of mass 30 kg from t₁ 1.0 seconds to t₂ -3.3 seconds. If the sled had an initial velocity TO THE RIGHT (in the positive direction) of V, 12 m/s, determine the final velocity of the sled. Record your answer with at least three significant figures.
The final velocity of the sled is -36.96 m/s, when recorded with at least three significant figures.
To calculate the final velocity of the sled, we need to use the equation of motion of an object when a constant force is applied to it.
The equation is given as,
v = u + at
Where v is the final velocity,
u is the initial velocity,
a is the acceleration, and
t is the time taken.
To solve the problem, we can use the equation,
a = F/m, where F is the force, and m is the mass of the sled.
Hence,
a = (13t^2 - 35t + 79)/30
Let's calculate the acceleration at t = 1.0 s and t = -3.3 s.
a₁ = (13(1.0)^2 - 35(1.0) + 79)/30
= 1.9 m/s²
a₂= (13(-3.3)^2 - 35(-3.3) + 79)/30
= 11.2m/s²
Now, let's calculate the change in velocity (Δv) of the sled.
Δv = v₂ - v₁
Where v₁ = 12 m/s (given) and v₂ is the final velocity.
v₂ = u + a₂t₂
Where t₂ - t₁ = 4.3 s (time taken for the sled to stop), and
u = 12 m/s (given).
v₂ = 12 + 11.202× (-3.3) = -24.96m/s
Hence,
Δv = v₂ - v₁
= -24.96 - 12
= -36.96m/s
Therefore, the final velocity of the sled is -36.96 m/s, when recorded with at least three significant figures.
Learn more about constant force here
https://brainly.com/question/1969164
#SPJ11
In the circuit shown in the figure, find the magnitude of current in the middle branch. To clarify, the middle branch is the one with the 4 Ohm resistor in it (as well as a 1 Ohm). 0.2 A 0.6 A 0.8 A 3.2 A
The magnitude of current in the middle branch is 0.857 A.
Given circuit diagram is:Resistors 2 Ω and 4 Ω are in parallel:
So, equivalent resistance of 2 Ω and 4 Ω is 4/3 Ω now this is in series with 1 Ω resistor, so the total resistance is:R = 1 + 4/3 = 7/3 Ω
Total voltage in the circuit is 10 V.Now, we can use Ohm's law to find the current: I = V / RSo, I = 10 / (7/3) = 30/7 A ≈ 4.29 A
Now, the current is dividing into three branches in the ratio of inverse of resistance of each branch.
Therefore, current through the middle branch is:Im = (1 / (1+2/3)) × 30/7= (1/5) × 30/7 = 6/7 ≈ 0.857 A
Therefore, the magnitude of current in the middle branch is 0.857 A.
Answer: 0.857 A
Know more about Ohm's law here,
https://brainly.com/question/1247379
#SPJ11
A cauterizer, used to stop bleeding in surgery, puts out 1.75 mA at 16.0kV. (a) What is its power output (in W)? W (b) What is the resistance (in MΩ ) of the path? \& MΩ
a) The power output of the cauterizer is 28 W.b) The resistance of the path is 9.14 MΩ.
(a) To find the power output of the cauterizer, we can use the formula:Power (P) = Voltage (V) x Current (I)orP = VIWe are given the voltage and current, so we can substitute the values:P = (16.0 kV)(1.75 mA) = 28 WTherefore, the power output of the cauterizer is 28 W.
(b) To find the resistance of the path, we can use Ohm's law:V = IRRearranging the formula, we get:I = V/RSubstituting the values we have:1.75 mA = 16.0 kV / RConverting the units of current to amperes:1.75 x 10^-3 A = 16,000 V / RDividing both sides by 1.75 x 10^-3 A:R = (16,000 V) / (1.75 x 10^-3 A)R = 9,142,857 Ω = 9.14 MΩTherefore, the resistance of the path is 9.14 MΩ.
Learn more about voltage here,
https://brainly.com/question/27861305
#SPJ11
A free electron has a kinetic energy 14.7eV and is incident on a potential energy barrier of U =32.3eV and width w=0.032nm. What is the probability for the electron to penetrate this barrier (in %)?
The probability for a free electron with a kinetic energy of 14.7 eV to penetrate a potential energy barrier of 32.3 eV and width 0.032 nm is very low, approximately 0.003%.
In quantum mechanics, the transmission probability of a particle through a potential energy barrier is described by the phenomenon of quantum tunneling. The probability of tunneling depends on various factors, including the width and height of the barrier, as well as the energy of the particle.
To calculate the transmission probability, we can use the transmission coefficient formula. The transmission coefficient (T) is given by T = [tex](1 + (U/E))^-2w^{2}[/tex], where U is the height of the potential energy barrier, E is the kinetic energy of the electron, and w is the width of the barrier. Plugging in the values, we have T = [tex](1 + (32.3 eV / 14.7 eV))^{2}[/tex] * 0.032 nm.
Calculating this expression, we find T ≈ 0.00003, or 0.003% when expressed as a percentage. This means that there is a very low probability for the electron to penetrate the barrier, indicating that most of the electrons will be reflected back rather than passing through.
Learn more about energy here ;
https://brainly.com/question/30672691
#SPJ11
It is desired to sample, by means of an ADC, any signal for which the following data is known: The maximum power of the signal reaches 800 mW The minimum power is 0.1 mW. Its maximum frequency reaches 10 kHz.
Determine:
a) The dynamic range (DR) of the signal.
b) The minimum number of bits of resolution (of the ADC) required to avoid distortion and that meets
with the SNR.
c) The conversion time required to satisfy the maximum frequency of the signal
a) The dynamic range (DR) of the signal is approximately 33.98 dB.
b) The minimum number of bits of resolution required for the ADC is 11 bits.
c) The conversion time required to satisfy the maximum frequency of the signal is 0.1 milliseconds.
a) The dynamic range (DR) of a signal is the ratio between the maximum and minimum power levels, expressed in decibels (dB). In this case, the dynamic range can be calculated using the formula DR = 10 * log10(maximum power/minimum power), which results in DR ≈ 33.98 dB.
b) The minimum number of bits of resolution required for the ADC can be determined based on the desired signal-to-noise ratio (SNR). The formula to calculate the required number of bits is N = ceil(log2(4 * SNR)), where SNR is the desired signal-to-noise ratio. Assuming a desired SNR of 6 dB, the minimum number of bits required would be N ≈ 11.
c) The conversion time required to satisfy the maximum frequency of the signal can be determined using the Nyquist-Shannon sampling theorem, which states that the sampling rate should be at least twice the maximum frequency. Therefore, the conversion time can be calculated as 1 / (2 * maximum frequency), resulting in a conversion time of approximately 0.1 milliseconds.
To know more about dynamic range (DR) click here:
https://brainly.com/question/31715117
#SPJ11
The magnetic field is 1.50 uT at a distance 42.6 cm away from a long, straight wire. At what distance is it 0.150 uT? 4.26×10 2
cm Previous Tries the middle of the straight cord, in the plane of the two wires. Tries 2/10 Previous Tries
The distance from the wire is 426 cm is the answer.
Given data: The magnetic field, [tex]B = 1.50 uT[/tex]
The distance from the long, straight wire, [tex]r1 = 42.6 cm.[/tex]
The magnetic field,[tex]B' = 0.150 uT[/tex]
To find: the distance from the wire, r2
Solution: We can use the Biot-Savart law to find the magnetic field at a distance r from an infinitely long straight wire carrying current I: [tex]B = μ0I / 2πr[/tex] where [tex]μ0 = 4π[/tex]× [tex]10^-7[/tex] Tm/A is the permeability of free space.
Now we can write this as: [tex]r = μ0I / 2πB[/tex] .....(1)
At [tex]r1, B = 1.50 uT[/tex] and at[tex]r2, B' = 0.150 uT[/tex]
Therefore, from equation (1):[tex]r2 = μ0I / 2πB'[/tex].....(2)
Let us assume the current in the wire is I. Since I is constant, we can write [tex]r2/r1 = B / B'.[/tex]....(3)
Substituting the values:[tex]r2 / 42.6 = 1.50 / 0.150[/tex]
Solving for [tex]r2:r2 = (42.6 × 1.50) / 0.150 = 426 cm[/tex]
Therefore, the magnetic field is 0.150 uT at a distance of 426 cm from the wire.
Thus, the distance from the wire is 426 cm.
know more about magnetic field
https://brainly.com/question/14848188
#SPJ11
A clock has a 10.0-g mass object bouncing on a spring that has a force constant of 0.9 N/m. What is the maximum velocity of the object if the object bounces 3.00 cm above and below its equilibrium position? Umax m/s How many joules of kinetic energy does the object have at its maximum velocity? KEmax x 10-4 -
A clock has a 10.0-g mass object bouncing on a spring that has a force constant of 0.9 N/m. the object has approximately 1.08 x 10^(-3) J of kinetic energy at its maximum velocity.
To find the maximum velocity of the object bouncing on the spring, we can use the principle of conservation of mechanical energy.
The maximum potential energy of the object can be calculated when it reaches its maximum displacement from the equilibrium position. Since the object bounces 3.00 cm above and below the equilibrium position, the total displacement is 2 * 3.00 cm = 6.00 cm = 0.06 m.
The maximum potential energy can be calculated using the equation:
PE_max = 0.5 * k * x^2,
where k is the force constant of the spring and x is the maximum displacement.
Substituting the given values:
PE_max = 0.5 * 0.9 N/m * (0.06 m)^2
= 0.00108 J
According to the conservation of mechanical energy, this potential energy is converted into kinetic energy when the object reaches its maximum velocity.
Therefore, the kinetic energy at maximum velocity is equal to the potential energy:
KE_max = 0.00108 J
In scientific notation, KE_max ≈ 1.08 x 10^(-3) J.
Therefore, the object has approximately 1.08 x 10^(-3) J of kinetic energy at its maximum velocity.
Learn more about mechanical energy here:
https://brainly.com/question/32458624
#SPJ11
A sailor uses an ultrasonic crack detector to find flaws in the rubber gasket ( S.G = 2.4, Y = 2.5 GPa) sealing water tight compartments. The crack detector produces 21.06 KHz pulses.
a) Calculate the speed of sound in the gasket in m/s
b) Calculate the wavelength
c) A crack is thought to be at a depth of 1.874 cm. Calculate the expected interval time for the pulse to make a round rip in μs.
The expected interval time for the pulse to make a round trip in the gasket is approximately 22.7 μs.
To calculate the speed of sound in the gasket, we can use the formula:
Speed of sound = Frequency × Wavelength
a) Calculate the speed of sound in the gasket in m/s:
Given:
Frequency = 21.06 KHz = 21.06 × 10^3 Hz
To calculate the speed of sound, we need the wavelength. Since the wavelength is not given directly, we can use the following formula to find it:
Wavelength = Speed of sound / Frequency
We know that the speed of sound in a material is given by:
Speed of sound = √(Young's modulus / Density)
Given:
Young's modulus (Y) = 2.5 GPa = 2.5 × 10^9 Pa
Density (ρ) = Specific gravity (SG) × Density of water
Density of water = 1000 kg/m^3 (approximate value)
Specific gravity (SG) = 2.4
Density (ρ) = 2.4 × 1000 kg/m^3 = 2400 kg/m^3
Now, we can substitute these values to calculate the speed of sound:
Speed of sound = √(2.5 × 10^9 Pa / 2400 kg/m^3)
= √(2.5 × 10^9 / 2400) m/s
≈ 1650.82 m/s
b) Calculate the wavelength:
Wavelength = Speed of sound / Frequency
= 1650.82 m/s / (21.06 × 10^3 Hz)
≈ 78.34 × 10^-6 m
≈ 78.34 μm
c) Calculate the expected interval time for the pulse to make a round trip in μs:
Given:
Depth of crack = 1.874 cm = 1.874 × 10^-2 m
The time taken for a round trip can be calculated as:
Round trip time = 2 × Depth of crack / Speed of sound
Round trip time = 2 × (1.874 × 10^-2 m) / 1650.82 m/s
≈ 2.27 × 10^-5 s
≈ 22.7 μs
Therefore, the expected interval time for the pulse to make a round trip in the gasket is approximately 22.7 μs.
Learn more about Wavelength here:
https://brainly.com/question/31143857
#SPJ11
You are sitting in a bus in a depot, when suddenly you see in the window the bus next to yours start to move forward. List two scenarios that could be happening
Analyse the stick diagram as shown in Figure Q2(b). (i) Transform the stick diagram into the equivalent schematic circuit at transistor level. (10 marks) (ii) Determine the Boolean equation representing the output Y. (4 marks) Figure Q2(b)
The above schematic circuit diagram is the equivalent schematic circuit at transistor level.
The Boolean equation representing the output Y is X + Z.
(i) Transformation of stick diagram into an equivalent schematic circuit at transistor level
The stick diagram given above represents the schematic diagram of the given Boolean expression using only MOS transistors as per the design rules. The stick diagram can be transformed into the equivalent schematic circuit at transistor level as shown below:
The above schematic circuit diagram is the equivalent schematic circuit at transistor level.
(ii) Determination of Boolean equation representing the output Y Boolean equation can be formed by observing the schematic circuit diagram obtained from the stick diagram.
The output of the given circuit diagram is represented by the output terminal Y which is labelled in the circuit diagram obtained above. The output Y is formed by OR operation of the two input terminals X and Z as seen in the diagram. Therefore the Boolean equation representing the output Y is given as:
Y = X + Z.
The Boolean equation representing the output Y is X + Z.
Learn more about Boolean https://brainly.com/question/2467366
#SPJ11
An object is placed 10cm in front of a concave mirror whose radius of curvature is 10cm calculate the position ,nature and magnification of the image produced
Answer:
The focal length, f = − 15 2 c m = − 7.5 c m The object distance, u = -10 cm Now from the mirror equation 1 v + 1 u = 1 f 1 v + 1 − 10 = 1 − 7.5 v = 10 × 7.5 − 2.5 = − 30 c m The image is 30 cm from the mirror on the same side as the object.
Calculate at point P(100, 100, 100) in free space, the radiated electric field intensities E,,and Ee, of a Im Hertzian dipole antenna located at the origin along z axis. The antenna is excited by a current i(t) = 1 x cos( 10m x 10°t) A
The answer is- cos(θ) = z/r = 100/√(100² + 100² + 100²) = 1/√3 and sin(θ) = √2/√3.
The electric field intensities E and Eθ of a 1m Hertzian dipole antenna in free space at point P(100, 100, 100) located at the origin along the z-axis and excited by a current i(t) = 1 x cos(10m x 10°t) A are given by; E = jIωl cos(θ) / 4πr²Eθ = - jIωl sin(θ) / 4πr² Where j = √-1 is the imaginary number I is the current flowing through the antenna, which is given as I = 1AL is the length of the dipole antenna, which is L = 1mω is the angular frequency of the oscillating current source, which is given as ω = 2πf = 2π(10MHz) = 20π x 10⁶rad/sθ is the angle between the line joining the origin and point P with the z-axis, given by cos(θ) = z/r = 100/√(100² + 100² + 100²) = 1/√3sin(θ) = √2/√3r is the distance between the dipole antenna and point P, given by r = √(100² + 100² + 100²) = 100√3/√3 x 100² = 10⁶λ = c/f = 3 x 10⁸/10⁷ = 30m where c is the speed of light in free space
Substituting the given values into the expressions for the electric field intensities;
E = j(1A)(20π x 10⁶ rad/s)(1m) (1/√3) cos(θ) / 4π(100√3)²
= 9.4 x 10⁻¹²cos(θ) VEθ
= -j(1A)(20π x 10⁶ rad/s)(1m) √2/√3 sin(θ) / 4π(100√3)²
= -9.4 x 10⁻¹²sin(θ) V.
The radiated electric field intensities E and Eθ of a 1m Hertzian dipole antenna located at the origin along the z-axis in free space at point P(100, 100, 100) is given by E = 9.4 x 10⁻¹²cos(θ) V and Eθ = -9.4 x 10⁻¹²sin(θ) V, where θ is the angle between the line joining the origin and point P with the z-axis, given by cos(θ) = z/r = 100/√(100² + 100² + 100²) = 1/√3 and sin(θ) = √2/√3.
know more about electric field
https://brainly.com/question/30544719
#SPJ11