The spring constant is 0.28 N/m if 14 oscillations take 11.0s.
In physics, oscillations are defined as a repetitive variation, typically in time, of some measure about a central value (often a point of equilibrium) or between two or more different states. The spring constant (k) is a measure of a spring's stiffness. It is the amount of force required to displace a spring a specific distance (typically one meter).
The spring constant formula is expressed as:-
F=kx
where k is the spring constant and x is the displacement produced by the force F.
We know that the air-track glider has a mass of 240 g, and it is attached to a spring. The glider is pushed 8.2 cm against the spring and then released. The oscillations are then observed, and it is found that 14 oscillations occur in 11.0 s.
We can calculate the spring constant by using this information.
Let us now calculate the spring constant k.
For a mass (m) attached to a spring, the formula for the time period T is:-
T=2π√m/k
We know that the time period T = 11/14 s. We also know that the glider has a mass of 240 g or 0.24 kg.
Now, we can solve the formula for the spring constant k as follows:-
k= 4π²m/T²k = 4π² × 0.24 kg / (11/14 s)²k = 0.28 N/m
Therefore, the spring constant is 0.28 N/m.
Learn more about oscillations: https://brainly.com/question/27237546
#SPJ11
what fraction of the engine power is being used to make the airplane climb? (the remainder is used to overcome the effects of air resistance and of inefficiencies in the propeller and engine.)
The fraction of the engine power used to make the airplane climb is 83% to two significant figures.
The power generated by the engine is given by the equation P=W/t, where P is power, W is work, and t is time.
The work done in lifting the airplane can be calculated as W=mgh, where m is mass, g is the gravitational constant, and h is the altitude gained.
Therefore, the power used to make the airplane climb can be calculated as P=mgh/t, where t is the time taken to gain the altitude.
Since the rate of climb is given as 2.5 m/s, the time taken to gain the altitude can be calculated as t=h/2.5, where h is the altitude gained.
Substituting the values into the equation, the power used to make the airplane climb can be calculated as P=750*9.8*h/2.5, where h is the altitude gained.
Therefore, the fraction of the engine power used to make the airplane climb is
P/(80*1000)=750*9.8*h/(2.5*80*1000).
Finally, the fraction of the engine power used to make the airplane climb expressed as a percentage is
(750*9.8 h/(2.5*80*1000))*100=83%.
For more question on engine click on
https://brainly.com/question/28206778
#SPJ11
a 170-hz sound travels through pure helium. the wavelength of the sound is measured to be 5.92 m. what is the speed of sound in helium?
The speed of sound in pure helium is approximately 1006.4 m/s.
When a sound wave travels through a medium, it produces a series of compressions and rarefactions in the medium, which causes the particles of the medium to vibrate. The speed of sound in a particular medium depends on the physical properties of the medium, such as its density, elasticity, and temperature.
The speed of sound in helium can be calculated using the formula,
speed of sound = frequency x wavelength
Given that the frequency of the sound is 170 Hz and the wavelength is 5.92 m, we can plug in these values and get,
speed of sound = 170 Hz x 5.92 m
speed of sound = 1006.4 m/s
To know more about sound, here
brainly.com/question/17095610
#SPJ4
dry air will break down and generate a spark if the electric field exceeds about 2.85e 6 n/c. how much charge could be packed onto a green pea (diameter 0.620 cm) before the pea spontaneously discharges?
2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.
The electric field at the surface of the sphere is given by the formula:
E = k × Q / r²
where:
k is the Coulomb's constant (8.99 × 10^9 N m²/C²),
Q is the charge on the sphere, and
r is the radius of the sphere.
Given:
Electric field strength for the breakdown, E = 2.85 × 10^6 N/C
Diameter of the pea, d = 0.620 cm = 0.0062 m
the electric field at the surface of the pea using the formula:
E = k × Q / r²
Q = E × r² / k
Q = 2.85 × 10⁶ × 0.0062²/ 8.99 × 10⁹
Q = 2.48 × 10⁻¹² C
Therefore, 2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.
To know more about electric fields, click here:
https://brainly.com/question/30544719
#SPJ12
what happens to the energy waves as they pass through the valley and reach the mountain? what type of material do you expect to find in valleys
When energy waves pass through the valley and reach the mountain, the waves will be reflected back, the material that you can expect to find in valleys are generally soil and rock formations.
The Energy waves are also formed by
Energy waves passing through valleys and reaching mountains undergo diffraction, causing them to curve and spread outwards.Valleys are formed by erosion and typically consist of dense materials like rocks, soil, and water, which can scatter, reflect or absorb the passing waves.The behavior of waves passing through valleys and mountains depends on various factors like wave type, angle of incidence, and material propertiesTo learn more about the energy waves :https://brainly.com/question/19036728
#SPJ11
a hard drive rotates at 7200 rpm. the disk has a diameter of 5.1 in 13 cm. what is the speed of a point 6.0 cm. from the center axle? what is the acceleration of this point on the disk.
The speed of a point 6.0 cm from the center axle is approximately 4.524 cm/s, and the acceleration of this point on the disk is approximately 3.408 cm/s².
The first step to solving this problem is to convert the rotational speed from revolutions per minute (rpm) to radians per second (rad/s):
ω = (7200 rpm) * (2π rad/rev) / (60 s/min) ≈ 753.98 rad/s
The speed of a point 6.0 cm from the center axle can be found using the formula:
v = r * ω
where r is the distance from the center axle to the point of interest. Substituting the given values, we get:
v = (6.0 cm) * 0.75398 rad/s ≈ 4.524 cm/s
To find the acceleration of this point on the disk, we can use the formula for centripetal acceleration:
a = r * ω²
where r is the distance from the center axle to the point of interest, and ω is the angular velocity in radians per second. Substituting the given values, we get:
a = (6.0 cm) * (0.75398 rad/s)² ≈ 3.408 cm/s²
Learn more about the rotational speed: https://brainly.com/question/17025846
#SPJ11
suppose the frequency of a note on an organ is 15 hz. what is the shortest organ pipe with both ends open that will resonate at this frequency? the velocity of sound in air is 343 m/s. answer in units of m.
The shortest organ pipe with both ends open that will resonate at a frequency of 15 Hz has a length of approximately 11.43 meters.
The wavelength of a sound wave is related to its frequency by the formula,
λ = v/f
where λ is the wavelength, v is the velocity of sound, and f is the frequency.
For a pipe with both ends open, the fundamental frequency (the lowest resonant frequency) is given by,
f = v/2L
where L is the length of the pipe.
We can combine these two equations to find the shortest length of an open pipe that will resonate at a frequency of 15 Hz,
λ = v/f = v/(v/2L) = 2L
L = λ/2 = v/(2f) = 343/(2*15) = 11.43 m
To know more about frequency, here
brainly.com/question/14634898
#SPJ4
What causes an object to become electrically charged?
An object becomes electrically charged when there is a transfer of electrons between two objects. Electrons are negatively charged particles that orbit the nucleus of an atom. When two objects come into contact with each other, some electrons may move from one object to the other. The object that loses electrons becomes positively charged, while the object that gains electrons becomes negatively charged.
This transfer of electrons can also occur without direct contact between the objects. For example, if a charged object is brought close to a neutral object, the electrons in the neutral object may be attracted or repelled by the charged object. This can cause the electrons in the neutral object to move around, resulting in a separation of charges and the object becoming charged.
Another way an object can become charged is through the process of induction. If a charged object is brought near a neutral object, it can induce a separation of charges in the neutral object. This happens because the charged object creates an electric field that attracts or repels electrons in the neutral object. The result is a separation of charges, with one part of the object becoming positively charged and the other part becoming negatively charged.
what is the spring constant of a spring that is compressed 5.0 cm and has 0.325 j of elastic potential energy stored in it?
The spring constant of a spring that is compressed 5.0 cm and has 0.325 j of elastic potential energy stored in it is 13 N/cm.
What is the spring constant?
This is because of the spring constant:
k = (2 * elastic potential energy) / (change in length)²
Where elastic potential energy is:
elastic potential energy = (1/2) * k * (change in length)²
Substituting the given values:
0.325 = (1/2) * k * (0.05)²
Simplifying:
0.325 = 0.00125k
Solving for k:
k = 0.325 / 0.00125
= 260 N/m
= 26 N/cm
Therefore, the spring constant of the given spring is 13 N/cm (since 1 N/m = 0.1 N/cm).
To know more about spring constant:
https://brainly.com/question/29975736
#SPJ11
c. what will be the charges of the spheres in fractions of after connection? how does the total charge of the two spheres after the connection compare to the initial charge of the left sphere?
The charges of the spheres after connection will be the same as the charge of the left sphere. The total charge of the two spheres after connection is equal to the initial charge of the left sphere.
To understand this, it is important to know that electric charge is a conserved quantity. This means that the net charge of a system cannot change. Therefore, if two objects with opposite charges (like the two spheres) are connected, the charges of the two objects will become equal and the total charge of the two spheres will remain the same as the initial charge of the left sphere.
To further understand this concept, consider two spheres with opposite charges. If the two spheres are not connected, then the total charge of the two spheres is equal to the sum of the charges of each sphere. However, if the two spheres are connected, the net charge of the system cannot change. Therefore, the charge of each sphere will become equal and the total charge of the two spheres after the connection will remain the same as the initial charge of the left sphere.
For more such questions on Electric charge.
https://brainly.com/question/12321627#
#SPJ11
what wavelength em radiation would be emitted most strongly by matter at the temperature of the core of a nuclear explosion, about 10,000,000 k?
The wavelength of electromagnetic radiation that would be emitted most strongly by matter at the temperature of the core of a nuclear explosion of 10,000,000 k will be 2.898 × 10^-10 meters.
Wavelength of electromagnetic radiationThe wavelength of electromagnetic radiation emitted by matter at a certain temperature can be determined using Wien's displacement law, which states that the wavelength of maximum emission (λmax) is inversely proportional to the temperature of the object:
λmax = b / T
where b is a constant known as Wien's displacement constant, equal to 2.898 × 10^-3 m·K.
Substituting the given temperature of 10,000,000 K into this equation, we get:
λmax = (2.898 × 10^-3 m·K) / (10^7 K) = 2.898 × 10^-10 m
Therefore, the wavelength of electromagnetic radiation emitted most strongly by matter at the temperature of the core of a nuclear explosion is approximately 2.898 × 10^-10 meters, which corresponds to the ultraviolet region of the electromagnetic spectrum.
More on electromagnetic radiations can be found here: https://brainly.com/question/4185163
#SPJ1
why do the phases of venus show that the solar system is in a heliocentric model instead of a geocentric model?
The phases of Venus show that the solar system is in a heliocentric model instead of a geocentric model because the heliocentric model states that the Sun is at the center of the solar system, while the geocentric model states that Earth is at the center of the universe.
The phases of Venus can only be explained in the heliocentric model because the planet is orbiting the Sun.The phases of Venus are an important piece of evidence supporting the heliocentric model proposed by Nicolaus Copernicus. The geocentric model was the widely accepted model of the universe until the 16th century when Copernicus proposed the heliocentric model, which suggested that the Sun is at the center of the solar system and the Earth and other planets orbit around it.
The phases of Venus show that it orbits the Sun and not the Earth because, as it orbits the Sun, different portions of the planet's sunlit side are visible from Earth. This can only occur in a heliocentric model because Venus is between the Earth and the Sun in its orbit, which causes it to pass through phases. Therefore, the phases of Venus are not consistent with a geocentric model, which suggests that Venus orbits the Earth.
Learn more about heliocentric at:
https://brainly.com/question/18403954
#SPJ11
calculate the efficiency of an electric motor which uses 7.4kJ of energy to lift a 34kg object 11m
The electric motor's efficiency is 51.06%.
What is the electric motor's efficiency?The majority of electric motors are made to operate between 50% and 100% of rated load. Typically, maximum efficiency is within 75% of rated load. Hence, the allowable load range for a 10-horsepower (hp) motor is between 5 and 10 hp; its peak efficiency is at 7.5 hp. Below roughly 50% load, a motor's efficiency tends to decline significantly.
To calculate the effort required to raise the object, use the formula:
Work = Force x Distance
= m x g x h (where m is the mass of the object, g is the acceleration due to gravity, and h is the height lifted)
= 34 kg x 9.81 m/s² x 11 m
= 3,769.34 J
The energy consumed by the electric motor is given as 7.4 kJ.
Therefore, the input power is:
Input power = Energy consumed / time taken
= 7.4 kJ / t
Efficiency=(Output power/Input power) x 100%
Output power = Work done/time taken
= 3,769.34 J / t
As a result, the electric motor's efficiency is:
Efficiency=(Output power/Input power)x 100%
= [(3,769.34 J / t) / (7.4 kJ / t)] x 100%
= 51.06%.
To know more about electric motor's visit:-
https://brainly.com/question/30033576
#SPJ1
if the frequency of the incoming light is decreased, will the energy of the ejected electrons increase, decrease, or stay the same?
If the frequency of the incoming light is decreased, the energy of the ejected electrons will decrease.
The frequency of the incoming light will affect the energy of the ejected electrons. This is because the energy of the ejected electrons is proportional to the frequency of the incoming light.
The energy of the electrons can be determined using the equation:
E = h * f,
where E is the energy, h is Planck’s constant, and f is the frequency of the incoming light. This equation shows that the energy of the electrons is directly proportional to the frequency of the incoming light.
Therefore, if the frequency of the incoming light is decreased, the energy of the ejected electrons will also decrease.
To know more about frequency, refer here:
https://brainly.com/question/14316711#
#SPJ11
suppose you want to connect a capacitor to a single 10.0-v battery. 1) what capacitance do you need to store 12.0 c of charge? (express your answer to three significant figures.)
To store 12.0 C of charge, you would need a capacitor with capacitance of 1.20 F.
Battery capacity is the amount of battery electric current that can be supplied/flown to an external circuit or load within a certain time (hours) to provide a certain voltage.
The capacitance required to store 12.0 C of charge in a capacitor connected to a single 10.0 V battery can be calculated using the formula,
Q = CV
where Q is the charge, C is the capacitance, and V is the voltage. Rearranging this equation, we get,
C = Q/V
Plugging in the given values, we get,
C = 12.0C/10.0V = 1.20 F
Therefore, the capacitance required to store 12.0 C of charge is 1.20 F (to three significant figures).
Learn more about battery capacity at https://brainly.com/question/30061793
#SPJ11
two objects collide and stop. their kinetic energy becomes sound energy. when does the energy stop being sound energy?
Answer: Two objects collide and stop. Their kinetic energy becomes sound energy when it is completely converted into another form of energy.
Sound energy is a form of energy that is generated due to the vibration of the particles. The sound energy is transferred through the air, liquids, and solids in the form of waves.
When two objects collide, their kinetic energy converts into sound energy. This sound energy is due to the collision of the objects. The kinetic energy is converted into sound energy because of the vibrations that occur during the collision.
When the sound energy is produced, it starts to propagate through the surrounding medium until it is absorbed by another medium. The energy stops being sound energy when it is completely converted into another form of energy. It can be absorbed by the medium in which it is traveling or can be transformed into other forms of energy such as heat or electrical energy.
Thus, the sound energy produced by the collision of two objects stops being sound energy when it is completely converted into another form of energy.
Learn more about sound energy here:
https://brainly.com/question/3369385#
#SPJ11
a light plane must reach a speed of 35 m/s for takeoff. how long a runway is needed if the (constant) acceleration is 3.0 m/s^2?
The length of runway needed for a light plane to take off with a constant acceleration of 3.0 m/s2 and a speed of 35 m/s is 203.7 meters.
The time taken for a light plane to reach 35 m/s from 0 m/s is given by using the formula,
v = u + at
where, v = final velocity, u = initial velocity, a = acceleration, and t = time
Here, the initial velocity of the plane is u = 0 m/s.
The final velocity of the plane is v = 35 m/s.
The acceleration of the plane is a = 3.0 m/s².
The time taken to reach the final velocity can be calculated as,
35 = 0 + (3.0)t
t = 35 / 3.0
t = 11.67 s
Therefore, the plane takes 11.67 s to reach a speed of 35 m/s for takeoff.
The distance traveled by plane during this time can be calculated as,
s = ut + 1/2 at²
s = 0 x 11.67 + 1/2 x 3.0 x (11.67)²
s = 203.7 m
Therefore, the runway should be at least 203.7 meters long if the acceleration is constant at 3.0 m/s².
Learn more about distance traveled at https://brainly.com/question/29409777
#SPJ11
your car is accelerating to the right from a stop.for the steps and strategies involved in solving a similar problem, you may view a
To solve the given problem, it is important to understand the concept of acceleration and the forces acting on the car. The acceleration of a car is the rate at which its velocity changes over time.
The forces acting on the car can be divided into two components: the force of friction between the tires and the road, and the force of gravity acting on the car.
The force of friction depends on the nature of the road surface and the type of tires on the car. The force of gravity depends on the mass of the car and the gravitational acceleration.
It is given that the car is accelerating to the right from a stop. This means that the car is moving in the positive x-direction with an increasing velocity.Identify the forces acting on the car: The forces acting on the car are the force of friction and the force of gravity. The force of friction is acting in the opposite direction to the motion of the car and is given by f = μN, where μ is the coefficient of friction and N is the normal force acting on the car. The force of gravity is acting in the downward direction and is given by Fg = mg, where m is the mass of the car and g is the gravitational acceleration.Analyze the motion of the car using the concepts of force and acceleration. The net force acting on the car is given by Fnet = ma, where a is the acceleration of the car. From Newton's second law, we can write Fnet = f - Fg = ma. Solving for a, we get a = (f - Fg)/m.Calculate the acceleration of the car by substituting the values of f, Fg, and m in the above equation, we get a = (μN - mg)/m. The normal force acting on the car is equal to the weight of the car, which is given by N = mg. Substituting this value in the above equation, we get a = (μ - g)/m. This is the expression for the acceleration of the car.Therefore, a = (μ - g)/m is the expression for the acceleration of the car.
To know more about acceleration click here:
https://brainly.com/question/30660316
#SPJ11
discuss how errors due to earth curvature and refraction can be eliminated from the differential leveling process.
Errors due to earth curvature and refraction can be eliminated from the differential leveling process by using the trigonometric leveling method.
This method utilizes the principle of triangles to determine the height difference between two points on the Earth's surface.
The trigonometric method begins by measuring the horizontal angle between two points, then the vertical angle between the same two points, and finally the distance between the points.
The trigonometric method is not affected by the curvature of the Earth or refraction since the vertical angle is measured at a given distance instead of the line of sight.
Therefore, the measurements of the angles and distances remain unaffected.
The trigonometric leveling process is as follows: first, an instrument is set up at point A. A second instrument is then set up at point B, and both instruments are leveled.
The horizontal angle between the two points is then measured with a theodolite, followed by the vertical angle. Lastly, the distance between the two points is measured using a tape measure.
After all the measurements are taken, the results are then used in a trigonometric formula to calculate the difference in elevation between the two points.
This method eliminates errors due to refraction or the Earth's curvature, since the elevation difference is not determined by the line of sight, but rather by the measured angles and distance.
The trigonometric leveling method is the best method to eliminate errors due to the Earth's curvature and refraction from the differential leveling process.
This method uses trigonometric principles and measurements to accurately calculate the difference in elevation between two points.
to know more about refraction refer here:
https://brainly.com/question/14760207#
#SPJ11
a) What is the y component of the vector given in the diagram? (120 N, 50 °) 120 N 50⁰ (C) 60 N (B) 92 N (D) 120 N (A) 77N
Answer: B
Explanation:
The y component of the vector is given by the formula:
y component = magnitude of the vector x sin(angle between the vector and the y-axis)
In this case, the magnitude of the vector is 120 N and the angle between the vector and the y-axis is 50 degrees. So we have:
y component = 120 N x sin(50°) ≈ 92 N
Therefore, the answer is (B) 92 N.
a pulley wheel is 77 mm diameter and transmits 1 kw of power at 373 rev/min. the maximum belt tension is 1,116 n at this point. calculate the initial tension applied to the stationary belts.
The initial tension applied to the stationary belts is 1116 N.
The initial tension applied to the stationary belts can be calculated by using the following equation: T = (9.55 * P * n)/(π * D), where T is tension, P is power, n is rev/min, and D is diameter.
The power transmitted by the pulley wheel (1 kW) multiplied by the number of revolutions per minute (373 rev/min) gives us the total energy transmitted.
This energy can be divided by the circumference of the pulley wheel (π * D, where D is the diameter of the wheel).
This provides us with the initial tension (T) applied to the stationary belts. Substituting in the given values of P, n, and D into the equation gives us the initial tension of 1,116 N.
To know more about circumference click on below link:
https://brainly.com/question/28757341#
#SPJ11
suppose we see the spectral lines to a distant star doppler shifted to smaller wavelengths. what does this tell us about the star's motion?
Suppose we see the spectral lines to a distant star doppler shifted to smaller wavelengths. This tells us that the star is moving toward the observer.
The Doppler effect, also known as the Doppler shift, is a phenomenon in which waves, such as sound or light waves, shift in frequency when their source and observer are moving relative to one another. As a result, the wavelength appears to be altered when the source of the waves approaches or recedes from the observer.
In this situation, if we see the spectral lines to a distant star Doppler shifted to smaller wavelengths, it suggests that the star is moving towards the observer. It is caused by the Doppler effect, which alters the frequency of light when its source is moving relative to the observer.
Learn more about Doppler effect at https://brainly.com/question/1330077
#SPJ11
when you look into a mirror, what is happening to the light?
When we look into a mirror, a process called reflection occurs with the light.
What happens to the light:
1. Light source: The process begins with a light source, such as the sun or a light bulb, emitting light waves in all directions.
2. Light traveling: The light waves travel through the air and reach the mirror.
3. Mirror's surface: Mirrors have a smooth, reflective surface made of glass with a thin layer of metal, usually aluminum or silver, on the back.
4. Incident light: The light waves that strike the mirror's surface are called incident light.
5. Reflection: The mirror's smooth surface causes the incident light waves to bounce off, or reflect, at the same angle at which they arrived.
This is known as the law of reflection, which states that the angle of incidence is equal to the angle of reflection.
6. Reflected light: The light waves that bounce off the mirror are called reflected light.
7. Image formation: As the reflected light waves travel away from the mirror, they converge at a point and form an image of the object you see in the mirror.
8. Observing the image: Your eyes detect the reflected light waves, and your brain processes this information to create the perception of the image you see in the mirror.
In summary, when you look into a mirror, the light emitted from a source travels towards the mirror, strikes its reflective surface, and bounces off at the same angle, following the law of reflection.
The reflected light then forms an image, which you observe as the reflection in the mirror.
For similar question on reflection.
https://brainly.com/question/29788343
#SPJ11
mass than air) at the same temperature. how does this affect the normal-mode frequencies of the pipe?
When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.
This is due to the fact that the speed of sound is proportional to the square root of the ratio of the bulk modulus to the density of the medium in which it travels.
When the density of the medium inside the pipe increases, the velocity of sound decreases, causing the frequency of the normal modes to decrease.
he wavelength of the sound waves inside the pipe is shortened due to the increase in density, resulting in a lower frequency of the normal modes.
The frequency of the normal modes of a pipe is influenced by a variety of factors, including the diameter and length of the pipe, as well as the speed of sound in the medium inside the pipe. T
he frequency of the normal modes is inversely proportional to the length of the pipe, with longer pipes producing lower frequencies.
In the case of a pipe filled with a liquid of higher density than air, the frequency of the normal modes would be lower than if it were filled with air.
This is because the speed of sound in the liquid would be lower than in air, resulting in a decrease in the frequency of the normal modes.
When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.
This is due to the fact that the speed of sound in the liquid is lower than in air, resulting in a decrease in the frequency of the normal modes.
to know more about frequency refer here:
https://brainly.com/question/14316711#
#SPJ11
what is the longest possible wavelength for the traveling waves that can interfere to form a standing wave on this string?
The longest possible wavelength for a standing wave on a string is: the length of the string itself
This is because, in order to create a standing wave, two traveling waves must interfere with one another and create a wave pattern that is fixed in space.
As the wavelength of the traveling waves increases, the nodes (points of zero displacements) of the standing wave become closer together. Therefore, if the wavelength is equal to the length of the string, the nodes of the standing wave are located at the two ends of the string and the wave pattern remains stationary.
This means that any longer wavelength traveling wave would not be able to interfere and form a standing wave on the string.
To know more about wavelength refer here:
https://brainly.com/question/13533093#
#SPJ11
on june 9, 1988, sergei bubka broke the world pole-vaulting record for the 8th time in four years by attaining a height of 6.10 m. how long did it take bubka to return to the ground from the highest part of his vault?
On june 9, 1988, Sergei Bubka broke the world pole-vaulting record for the 8th time in four years by attaining a height of 6.10 m. It took Bubka 1.11 seconds to return to the ground from the highest part of his vault.
Sergei Bubka broke the world pole-vaulting record for the 8th time in four years by attaining a height of 6.10 m on June 9, 1988. It is required to determine how long it took Bubka to return to the ground from the highest point of his vault. In order to determine the time taken for Bubka to return to the ground, we need to consider the concepts of kinetic energy and potential energy. The pole vaulter gains potential energy during the ascent phase of the vault as he gains altitude. When he reaches the highest point, he has the maximum potential energy. During the descent phase of the vault, the potential energy is converted into kinetic energy.
Based on this principle, we can use the conservation of energy equation to find the time taken by Bubka to return to the ground. The equation for conservation of energy is given as: Potential energy (P.E) = Kinetic energy (K.E)
P.E = mgh where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object above the ground.
K.E = 1/2 mv² where v is the velocity of the object.
The velocity of Bubka when he reached the highest point can be assumed to be zero since he had to come to a stop before starting his descent. Therefore, the initial kinetic energy is zero.
P.E at the highest point = K.E at the lowest point
Let t be the time taken by Bubka to return to the ground. We can assume that Bubka moves with uniform acceleration. Using the kinematic equation, we have: v = u + at where u is the initial velocity and a is the acceleration.
When Bubka reaches the ground, his final velocity is zero.
Therefore, we have: v = 0u = at
Substituting the value of u in the equation for K.E, we have: K.E = 1/2 mv² = 1/2 ma²t²
Substituting the value of P.E and K.E in the equation for conservation of energy, we have:
mgh = 1/2 ma²t²
Simplifying, we get: t = sqrt(2h/g)
Substituting the values of h and g, we have:
t = sqrt(2 x 6.10 / 9.81)t = sqrt(1.240)t = 1.11 seconds
Therefore, it took Bubka 1.11 seconds to return to the ground from the highest part of his vault.
For more such questions on Sergei Bubka.
https://brainly.com/question/30345268#
#SPJ11
gravitational potential energy when potential energy0.25 kg ball is suspended from a light spring.find gravitaional potential energy.g
The gravitational potential energy of a 0.25 kg ball suspended from a light spring is 0.6125 J.
Calculate the gravitational potential energy below.
The gravitational potential energy formula is as follows:
GPE = mgh
where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object from a reference point.
Since the ball is suspended from a light spring, the reference point is at the resting position of the ball, which is the same height as the spring's unstretched length. As a result, h is the length of the stretched spring.
Assume the stretched length of the light spring is 0.25 m, and the acceleration due to gravity is [tex]9.8 m/s^2[/tex].
GPE = mgh
= 0.25 × 9.8 × 0.25
= 0.6125 J
for such more question on gravitational potential energy
https://brainly.com/question/15896499
#SPJ11
time dilation. a. a clever student, after learning about the theory of relativ?ity, decides to apply his knowledge in order to prolong his life. he decides to spend the rest of his life in a car, trave?ling around the freeways at 55 miles per hour (89 km/hr). suppose he drives for a period of time during which 70 years pass in his house. how much time will pass in the car? (hint: if you are unable to find a difference, be sure to explain why.) b. an even more clever student decides to prolong her life by cruising around the local solar neighborhood at a speed of 0.95c (95% of the speed of light). how much time will pass on her spacecraft during a period in which 70 years pass on earth? will she feel as if her life span has been extended? explain. c. suppose you stay home on earth while your twin sister takes a trip to a distant star and back in a spaceship that travels at 99% of the speed of light. if both of you are 25 years old when she leaves and you are 45 years old when she returns, how old is your sister when she gets back?
The time that passes in the car is approximately 70 years. when the sister returns from the trip, she would be approximately 319.15 years old according to Earth's reference frame.
a. To calculate the time that passes in the car, we can use the concept of time dilation in special relativity. The formula for time dilation is:
[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]
where [tex]\( \Delta t' \)[/tex] is the time experienced in the moving frame (car), [tex]\( \Delta t \)[/tex] is the time experienced in the stationary frame (house), [tex]\( v \)[/tex] is the velocity of the car, and [tex]\( c \)[/tex] is the speed of light.
Given:
Velocity of the car, [tex]\( v = 89 \, \text{km/hr} = \frac{89}{3.6} \, \text{m/s} \)[/tex]
Time experienced in the stationary frame (house), [tex]\( \Delta t = 70 \, \text{years} \)[/tex]
Converting the velocity to meters per second:
[tex]\[ v = \frac{89}{3.6} = 24.72 \, \text{m/s} \][/tex]
Substituting the given values into the time dilation formula:
[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - \left(\frac{24.72}{299792458}\right)^2}} \][/tex]
Simplifying the expression:
[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - 8.7203 \times 10^{-17}}} \][/tex]
Since the value inside the square root is extremely close to 1, we can approximate the square root as 1:
[tex]\[ \Delta t' \approx \frac{70}{\sqrt{1}} = 70 \, \text{years} \][/tex]
Therefore, the time that passes in the car is approximately 70 years.
b. Using the same formula for time dilation, we can calculate the time that passes on the spacecraft. Given that the speed of the spacecraft is 0.95c, where c is the speed of light, we have:
[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]
Given:
The velocity of the spacecraft, [tex]\( v = 0.95c \)[/tex]
Time experienced on Earth, [tex]\( \Delta t = 70 \, \text{years} \)[/tex]
Substituting the values:
[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - (0.95)^2}} \][/tex]
Simplifying the expression:
[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - 0.9025}} \\\\= \frac{70}{\sqrt{0.0975}} \]\\\\\ \Delta t' = \frac{70}{0.31224} \approx 224.33 \, \text{years} \][/tex]
Therefore, during a period of 70 years on Earth, approximately 224.33 years pass on the spacecraft. The clever student will perceive that her life span has been extended because more time has passed for her relative to the observers on Earth.
c. In this scenario, the twin sister is traveling to a distant star and back at a speed of 0.99c. The time experienced in the stationary frame (Earth) is given by [tex]\( \Delta t \)[/tex], which is 45 years. The time experienced in the moving frame (spaceship) is given by [tex]\( \Delta t' \)[/tex].
Using the time dilation formula:
[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]
Given:
The velocity of the spaceship, [tex]\( v = 0.99c \)[/tex]
Time experienced on Earth, [tex]\( \Delta t = 45 \, \text{years} \)[/tex]
Substituting the values:
[tex]\[ \Delta t' = \frac{45}{\sqrt{1 - (0.99)^2}} \][/tex]
Simplifying the expression:
[tex]\[ \Delta t' = \frac{45}{\sqrt{1 - 0.9801}} \\\\= \frac{45}{\sqrt{0.0199}} \]\\\\\ \Delta t' = \frac{45}{0.141} \approx 319.15 \, \text{years} \][/tex]
Therefore, when the sister returns from the trip, she would be approximately 319.15 years old according to Earth's reference frame.
Know more about time dilation:
https://brainly.com/question/30493090
#SPJ12
europa, one of the moons of jupiter, was discovered by galileo in 1610. europa has a circular orbit of radius 6.708 105 km and period 3.551 days. find the mass of jupiter.
Therefore, the mass of Jupiter is approximately 1.898 × 1027 kg.
The mass of Jupiter can be calculated using the equation M = (4π2 r3)/(G P2), where M is the mass of Jupiter, r is the orbital radius of Europa (6.708 105 km), G is the gravitational constant (6.674 × 10-11 m3 kg-1 s-2), and P is the orbital period of Europa (3.551 days).
The circular orbit of Europa is given as, r = 6.708 × 105 km. The period of Europa is given as, T = 3.551 days are supposed to calculate the mass of Jupiter. In order to calculate the mass of Jupiter, we need to use Kepler's 3rd law. Kepler's 3rd law is given as, T2 = (4π2/GM) × r3 where T is the period of orbit, G is the gravitational constant, M is the mass of the planet, and r is the radius of the orbit.
By rearranging the above formula we get, M = (4π2r3) / (GT2)Substituting the given values, we get, M = (4π2 × (6.708 × 105)3) / ((6.67430 × 10-11) × (3.551 × 24 × 60 × 60)2) ≈ 1.898 × 1027 kg. Therefore, the mass of Jupiter is approximately 1.898 × 1027 kg.
You can read more about Jupiter at https://brainly.com/question/2715802#:
#SPJ11
how much charge does a 9.0 v battery transfer from the negative to the positive terminal while doing 45 j of work? express your answer to two significant figures and include the appropriate units.
The amount of charge transferred is 4.5C (coulombs). This is calculated by dividing 45 J (joules) of work by 9.0 V (volts) of voltage.
We can use the equation W = qV, where W is the work done, q is the charge transferred, and V is the potential difference (voltage) across the battery.
Rearranging the equation to solve for q, we get q = W/V.
Plugging in the values given, we have:
q = 45 J / 9.0 V
q = 5.0 C
Therefore, the battery transfers 5.0 coulombs of charge from the negative to the positive terminal while doing 45 J of work.
Learn more about voltage at: https://brainly.com/question/1176850
#SPJ11
suppose you take off in a car with your physics book on top. if you are accelerating forward and the book rides with you, in what direction does friction act on the book
When you takes off in a car with a physics book on top, if the person is accelerating forward and the book rides with you, then friction will act on the book in the opposite direction to the motion of the book, this means that the direction of friction acting on the book will be in the backward direction.
The friction always acts in the opposite direction to the motion of the object. When the car accelerates forward, the book also starts to move forward with the same speed as the car. However, the book is still in contact with the car's seat, and the seat exerts a force of friction on the book.
According to Newton's third law of motion, the book also exerts an equal and opposite force of friction on the seat. Since the book is moving in the forward direction, the direction of friction acting on it will be opposite to the direction of motion, which means that friction will act in the backward direction. Therefore, the direction of friction acting on the book is in the backward direction.
Learn more about Newton's third law at:
https://brainly.com/question/29768600
#SPJ11