The average force exerted on the person if he is stopped by a padded dashboard that compresses an average of 1.00 cm is 5.54 * 10³ N, and the average force exerted on the person if he is stopped by an airbag that compresses an average of 15.0 cm is 2.60 * 10⁴ N.
The impact of a vehicle during an accident can result in serious injury or even death. Therefore, it is necessary to calculate the force exerted on a passenger during an accident. Here are the calculations to determine the average force on the person if he is stopped by a padded dashboard that compresses an average of 1.00 cm and an airbag that compresses an average of 15.0 cm.
Mass of the person, m = 87.0 kg
Velocity of the car, v = 24.0 m/s
Compression distance by the padded dashboard, d1 = 1.00 cm
Compression distance by the airbag, d2 = 15.0 cm
The momentum of a body is given as:
P = m * v
The above equation represents the initial momentum of the passenger in the car before the collision. Now, after the collision, the passenger comes to rest, and the entire momentum of the passenger is absorbed by the padded dashboard and the airbag. Therefore, the force exerted on the passenger during the collision is:
F = Δp / Δt
Here, Δt is the time taken by the dashboard and the airbag to come to rest. Therefore, it is assumed that the time is the same for both cases. Therefore, we can calculate the average force exerted on the person by the dashboard and the airbag as follows:
Average force exerted by the dashboard,
F1 = Δp / Δt1 = m * v / t1
The distance over which the dashboard is compressed is d1 = 1.00 cm = 0.01 m. Therefore, the time taken by the dashboard to come to rest is:
t1 = √(2 * d1 / a)
Here, a is the acceleration of the dashboard, which is given as a = F1 / m.The above equation can be written as:F1 = m * a = m * (√(2 * d1 / t1²))
Therefore, the average force exerted by the dashboard can be calculated as:
F1 = m * (√(2 * d1 * a)) / t1 = 5.54 * 10³ N
Average force exerted by the airbag,
F2 = Δp / Δt2 = m * v / t2
The distance over which the airbag is compressed is d2 = 15.0 cm = 0.15 m. Therefore, the time taken by the airbag to come to rest is:t2 = √(2 * d2 / a)
Here, a is the acceleration of the airbag, which is given as a = F2 / m.
The above equation can be written as:
F2 = m * a = m * (√(2 * d2 / t2²))
Therefore, the average force exerted by the airbag can be calculated as:
F2 = m * (√(2 * d2 * a)) / t2 = 2.60 * 10⁴ N
Therefore, the average force exerted on the person if he is stopped by a padded dashboard that compresses an average of 1.00 cm is 5.54 * 10³ N, and the average force exerted on the person if he is stopped by an airbag that compresses an average of 15.0 cm is 2.60 * 10⁴ N.
Learn more about force at: https://brainly.com/question/12785175
#SPJ11
A cube is 2.0 cm on a side when at rest. (a) What shape does it
take on when moving past an observer at 2.5 x 10^8 m/s, and (b)
what is the length of each side?
Answer: The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
The question is asking us to consider the relativistic effect of time dilation and length contraction, which affect the measurement of distance and time by a moving observer. Therefore, the apparent length and shape of the cube will differ from the actual measurements as seen by an observer at rest.
a) When the cube moves past an observer at a velocity of 2.5 x 10^8 m/s, it takes on a shape that is flattened in the direction of motion. This is because of the relativistic effect of length contraction. This effect states that the length of an object appears shorter to an observer in motion than to an observer at rest.
The degree of length contraction increases with velocity and is given by the formula: L' = L₀ / γ
where L₀ is the length at rest, L' is the apparent length observed by a moving observer, and γ is the Lorentz factor given by :
γ = 1 / √(1 - v²/c²) where v is the velocity of the cube and c is the speed of light.
Substituting the values, we have:
L' = 2.0 cm / γL'
= 2.0 cm / √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L'
= 0.47 cm.
b) The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is given by: L' = L₀ / γL = L' x γSubstituting the values, we have:
L = L' x γL
= 0.47 cm x √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L
= 1.22 cm.
Thus, the length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
Learn more about time dilation : https://brainly.com/question/3747871
#SPJ11
A gun is fired vertically into a block of wood (mass ml) at rest directly above it. If the bullet has a mass of m2 and a speed of v, how high will the block rise into the air after the bullet becomes embedded in it?
Answer: the height to which the block will rise into the air after the bullet becomes embedded in it is given by
H = (m₂v)² / 2(m₁ + ml)g.
When a gun is fired vertically into a block of wood at rest directly above it, the velocity of the block can be calculated by applying the law of conservation of momentum. Here, the bullet of mass m₂ is fired into the block of wood of mass ml. According to the law of conservation of momentum, the initial momentum of the bullet and the final momentum of the bullet and the block combined must be equal, and it can be expressed as:m₂v = (m₁ + ml)VWhere V is the velocity of the bullet and the block combined.
From the equation, we have: V = m₂v / (m₁ + ml)As the bullet and the block rise to a maximum height H, their total energy is equal to their initial kinetic energy, given as: 1/2 (m₁ + m₂) V² = (m₁ + m₂)gh. Where g is the acceleration due to gravity. Solving for H, we get: H = V² / 2g
Substituting the value of V in the above equation, we have: H = (m₂v)² / 2(m₁ + ml)g.
Therefore, the height to which the block will rise into the air after the bullet becomes embedded in it is given by H = (m₂v)² / 2(m₁ + ml)g.
Learn more about momentum: https://brainly.com/question/1042017
#SPJ11
As a woman walks, her entire weight is momentarily placed on one heel of her high-heeled shoes. Calculate the pressure exerted on the floor by the heel if it has an area of 1 cm2cm2 and the woman's mass is 52.5 kg. Express the pressure in Pa. (In the early days of commercial flight, women were not allowed to wear high-heeled shoes because aircraft floors were too thin to withstand such large pressures.)
P=
The pressure exerted on the floor by the heel is 5.15025 × 10⁷ Pa.
Given data,Mass of the woman, m = 52.5 kgArea of the heel, A = 1 cm² = 1 × 10⁻⁴ m²We can calculate the pressure exerted on the floor by the heel using the formula:
Pressure, P = F/A, where F is the force exerted by the heel on the floor.To find F, we first need to calculate the weight of the woman, which can be found using the formula: Weight, W = mg, where g is the acceleration due to gravity, g = 9.81 m/s²Weight of the woman, W = mg = 52.5 × 9.81 = 515.025 N.
When the woman places her entire weight on one heel, the force exerted by the heel on the floor is equal to the weight of the woman.Force exerted by the heel, F = 515.025 NPressure, P = F/A = 515.025/1 × 10⁻⁴ = 5.15025 × 10⁷ Pa.
Therefore, the pressure exerted on the floor by the heel is 5.15025 × 10⁷ Pa.
Learn more about Mass here,
https://brainly.com/question/86444
#SPJ11
How much larger is the dameter of the sun compared to the
diameter of jupiter?
The diameter of the sun is about 109 times larger than the diameter of Jupiter.
How much larger is the diameter of the sun compared to the diameter of Jupiter?The diameter of the sun is about 109 times larger than the diameter of Jupiter. The diameter of the sun is approximately 1.39 million kilometers (864,938 miles), while the diameter of Jupiter is around 139,822 kilometers (86,881 miles).
Therefore, the difference between the diameter of the sun and the diameter of Jupiter is about 1,390,178 kilometers (864,938 - 86,881 x 2), which is over one million kilometers. Jupiter is the largest planet in our solar system, but it's still small compared to the sun. Jupiter has a diameter that is roughly 11 times greater than the diameter of Earth.
The sun and Jupiter are both celestial objects in our solar system. While they share certain characteristics, such as their spherical shape and their immense size, they also differ in many ways. One significant difference between the sun and Jupiter is their size, as evidenced by their diameters. The diameter of the sun is around 109 times greater than the diameter of Jupiter, which means that the sun is much larger than Jupiter. The diameter of the sun is roughly 1.39 million kilometers (864,938 miles), while the diameter of Jupiter is about 139,822 kilometers (86,881 miles). The difference between the two is over 1,390,000 kilometers (864,938 - 86,881 x 2), which is a difference of over one million kilometers. As the largest planet in our solar system, Jupiter is still quite small when compared to the sun.
The diameter of the sun is about 109 times larger than the diameter of Jupiter, making it much larger than Jupiter.
To know more about solar system visit:
brainly.com/question/32240766
#SPJ11
A copper wire used for house hold electrical outlets has a radius of 2.0 mm (1mm = 10³m). Each Copper atom donates one electron for conduction. If the electric current in this wire is 15 A. copper density is 8900 kg/m³ and its atomic mass is 64 u, (lu = 1.66 x 10-27 kg), the electrons drift velocity Va in this wire is a) 2.11 x 10-4 m/s. b) 2.85 x 10-4 m/s. c) 8.91 x 10-5 m/s, d) 1.14 x 10-4 m/s. e) 4.56 x 10-5 m/s, f) None of the above.
The drift velocity (Va) of electrons in the copper wire can be calculated using the formula Va = I / (nAe), In this case, with a given current of 15 A and the properties of copper, the drift velocity is approximately 8.91 x 10^-5 m/s (option c).
The drift velocity of electrons in a wire is the average velocity at which they move in response to an applied electric field. It can be calculated using the formula Va = I / (nAe), where I is the current flowing through the wire, n is the number of charge carriers per unit volume, A is the cross-sectional area of the wire, and e is the charge of an electron.
In this case, the current is given as 15 A. The number of charge carriers per unit volume (n) can be determined using the density of copper (ρ) and its atomic mass (m). Since each copper atom donates one electron for conduction, the number of charge carriers per unit volume is n = ρ / (mN_A), where N_A is Avogadro's number.
The cross-sectional area of the wire (A) can be calculated using the radius (r) of the wire, which is given as 2.0 mm. The area is A = πr^2. By substituting the given values into the formula, we can calculate the drift velocity Va, which comes out to be approximately 8.91 x 10^-5 m/s. Therefore, option c is the correct answer.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
A wave is represented by the equation = . ( − ), where x and y in meters, t in seconds. Find the amplitude, wavelength, frequency, wave speed and direction. Find the displacement at t = 0.05 second and at a point x = 0.40 m.
the specific values for the amplitude, wavelength, frequency, wave speed, direction, and displacement at t = 0.05 s and x = 0.40 m can be determined by applying the equations and substituting the given values.
The equation for the wave is given as y(x, t) = A sin(kx - ωt), where:A represents the amplitude of the wave.k is the wave number, related to the wavelength λ by the equation k = 2π/λ.ω is the angular frequency, related to the frequency f by the equation ω = 2πf.From the equation, we can deduce the following information:The amplitude of the wave is equal to A.
The wavelength λ can be determined by the equation λ = 2π/k.The frequency f is given by f = ω/(2π).The wave speed v is related to the frequency and wavelength by the equation v = λf = ω/k.The direction of the wave can be determined by observing the sign of the coefficient of x in the equation.
A positive sign indicates a wave propagating in the positive x-direction, and a negative sign indicates a wave propagating in the negative x-direction.To find the displacement at a specific time and position, we substitute the given values of t and x into the equation y(x, t) and evaluate it.By using the given equation and substituting the provided values of t = 0.05 s and x = 0.40 m, we can calculate the displacement at that point in the wave.Therefore, the specific values for the amplitude, wavelength, frequency, wave speed, direction, and displacement at t = 0.05 s and x = 0.40 m can be determined by applying the equations and substituting the given values.
Learn more about wave here:
https://brainly.com/question/25954805
#SPJ11
An annulus with inner radius a=1.6 m and outer radius b=3.8 m lies in the x−y plane. There is a constant electric field with magnitude 9.9 m
V
, that makes an angle θ=65.9 ∘
with the horizontal. What is the electric flux through the annulus? V⋅m 1 point possible (graded) An annulus with inner radius a=1.6 m and outer radius b=3.8 m lies in the x−y plane. There is a constant electric field with magnitude 9.9 m
V
, that makes an angle θ=65.9 ∘
with the horizontal. What is the electric flux through the annulus? V⋅m
the electric flux through the annulus is 34.3 V m.
Given that the inner radius of the annulus, a = 1.6 m, the outer radius of the annulus, b = 3.8 m, the magnitude of the electric field, E = 9.9 m V, and the angle between the horizontal and electric field, θ = 65.9°.
The formula to calculate the electric flux is given by,Φ = E.A cosθWhere E is the magnitude of the electric field, A is the area of the surface, and θ is the angle between the electric field and the normal to the surface.
The area of the annulus is given by,A = π(b² - a²)Substituting the given values in the above equation, we get,A = π(3.8² - 1.6²)A = 12.2 π m²Now substituting the values of E, A, and θ in the electric flux formula, we get,Φ = E.A cosθΦ = 9.9 × 12.2π × cos 65.9°Φ = 34.3 V mHence,
the electric flux through the annulus is 34.3 V m.
to know more about electric flux
https://brainly.com/question/26289097
#SPJ11
Hydroelectric generators at Hoover Dam produce a maximum current of 8.05 x 10³ A at 251 kV. a) What is the power output? ___________________ W b) The water that powers the generators enters and leaves the system at low speed (thus its kinetic energy does not change) but loses 155 m in altitude. How many cubic meters per second are needed, assuming 86 % efficiency? __________ m³/s
The power output Hydroelectric generators at Hoover Dam produce a maximum current of 8.05 x 10³ A at 251 kV is 2.022 x 10⁹W. Cubic meters per second needed by assuming 86 % efficiency is 1547.83 m³/s.
a) The formula to calculate the power output is,
Power (P) = Current (I) x Voltage (V)
It is given that, Current (I) = 8.05 x 10³ A and Voltage (V)= 251 kV= 251,000 V
Substituting these values into the formula:
Power = (8.05 x 10³ A) x (251,000 V)
Power = 2.022 x 10⁹ W
Therefore, the power output is 2.022 x 10⁹ watts.
b) To calculate the flow rate of water needed, we can use the formula:
Power (P) = Efficiency (η) x Density (ρ) x Acceleration due to gravity (g) x Flow rate (Q) x Height (h)
It is given that, Power (P) = 2.022 x 10⁹ W, Efficiency (η) = 0.86 (86% efficiency), Density of water (ρ) = 1000 kg/m³, Acceleration due to gravity (g) = 9.8 m/s², Height (h) = 155 m
Substituting these values into the formula:
2.022 x 10⁹ W = 0.86 x (1000 kg/m³) x (9.8 m/s²) x Q x 155 m
Simplifying the equation:
Q= (2.022 x 10⁹ W) / (0.86 x 1000 kg/m³ x 9.8 m/s² x 155 m)
Q=1547.83 m³/s
Therefore, 1547.83 cubic meters per second of water are needed, assuming 86% efficiency.
To learn more about power: https://brainly.com/question/11569624
#SPJ11
A coil of inductance 130 mH and unknown resistance and a 1.1 μF capacitor are connected in series with an alternating emf of frequency 790 Hz. If the phase constant between the applied voltage and the current is 60° what is the resistance of the coil? Number Units
The resistance of the coil is 349.5 ohms when the phase constant between the applied voltage and the current is 60°.
Inductance = 130 mH
capacitance (C) = 1.1 μF
Frequency = 790 Hz.
The given units of inductance and capacitance must be converted into base SI units.
Inductance = 130 mH = 0.130 H
capacitance (C) = 1.1 μF = 1.1 μF = [tex]1.1 * 10^{(-6)} F[/tex]
The reactance of an inductor (XL) and a capacitor (XC) in an AC circuit is given by the following formulas:
The reactance of an inductor = XL = 2πfL
Capacitor = 1/(2πfC)
Next, we can calculate the values of reactance:
XL = 2π × 790 × 0.130 = 645.4 Ω (ohms)
XC = 1/(2π × 790 × [tex]1.1 * 10^{(-6)} F[/tex])
XC = 181.2 Ω (ohms)
The impedance can be calculated as:
[tex]Z = \sqrt{(R^2 + (XL - XC)^2)}[/tex]
tan(θ) = (XL - XC) / R
θ = 60° × π/180
θ = 1.047 radians
tan(1.047) = (645.4 - 181.2) / R
R = (645.4 - 181.2) / tan(1.047)
R = 349.5 Ω
Therefore, we can infer that the resistance of the coil is 349.5 ohms.
To learn more about Resistance
https://brainly.com/question/29550977
#SPJ4
A cart with mass 200 g moving on a friction-less linear air track at an initial speed of 1.2 m/s undergoes an elastic collision with an initially stationary cart of unknown mass. After the collision, the first cart continues in its original direction at 1.00 m/s. What is the mass of the second cart?
The mass of the second cart is 0 kg, indicating that it is an object with negligible mass or a stationary object.
In an elastic collision, the total momentum before and after the collision remains constant. We can express this principle using the equation:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
Where m1 and m2 are the masses of the first and second carts, v1 and v2 are their initial velocities, and u1 and u2 are their velocities after the collision.
In this scenario, the initial velocity of the first cart is given as 1.2 m/s, and its velocity after the collision is 1.00 m/s. The mass of the first cart is 200 g, which is equivalent to 0.2 kg.
We can rearrange the equation and solve for the mass of the second cart:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
(0.2 * 1.2) + (m2 * 0) = (0.2 * 1.2) + (m2 * 1.00)
0.24 = 0.24 + m2
By subtracting 0.24 from both sides, we find that m2 = 0 kg.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
A loop of wire with velocity 3 m/s moves through a magnetic field whose strength increases with distance at a rate of 5T/m. If the loop has area 0.75 m² and internal resistance 5 Ω, what is the current in the wire?
A. I=3 A
B. I=56A
C. I=11.25 A
D. I=2.25A
The current in the wire is option is A, I = 3A.
The rate of increase of the magnetic field is 5 T/m and the velocity of the wire is 3 m/s.
Therefore, the change in the magnetic field per unit time, that is, the emf induced in the wire is;
emf = Bvl
where
B is the magnetic field,
v is the velocity,
l is the length of the wire, in this case, the length of the wire is equal to the perimeter of the loop.
The area of the loop is 0.75 m²;
therefore, the perimeter is;
P = √(4 × 0.75 m² / π) = 0.977m
Substituting the values given;
emf = (5 T/m × 3.08 m) × 3 m/s = 14.655 V
The current in the wire is given by;
I = emf / R
where
R is the internal resistance of the wire, in this case, it is 5 Ω.
Substituting the values in the equation,
I = 14.655 V / 5 Ω = 2.931 A = 3A(approx)
Therefore, the correct option is A. I = 3A.
Learn more about current:
https://brainly.com/question/1100341
#SPJ11
Two pistons of a hydraulic lift have radii of 2.67 cm and 20.0 cm. A mass of 2.00×10^3 kg is placed on the larger piston. Calculate the minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston.
------------- N
The minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston is 348.8 N.
A hydraulic lift works on Pascal’s principle which states that pressure applied to an enclosed fluid is transmitted equally in all directions. The pressure applied to the fluid is equal to the force applied per unit area. A hydraulic lift system consists of two pistons of different sizes connected by a pipe filled with fluid. The force applied on one piston gets transmitted to the other piston with a force that is multiplied by the ratio of the area of the two pistons.
The area of the smaller piston is given as follows:A = πr²where r = 2.67 cm = 0.0267 mTherefore, A = π(0.0267)² = 0.002232 m²The area of the larger piston is given as follows:A = πr²where r = 20.0 cm = 0.20 mTherefore, A = π(0.20)² = 0.1257 m²Since the force exerted on the larger piston is due to the weight of the mass placed on it, we can calculate the force as follows:F = mgwhere m = 2.00×10³ kg, and g = 9.81 m/s²Therefore, F = (2.00×10³)(9.81) = 19.62 kN = 1.962×10⁴ N.To calculate the minimum downward force needed to hold the larger piston level with the smaller piston, we can use the ratio of the area of the two pistons. Let F₁ be the force needed to be exerted on the smaller piston.
Therefore, the force exerted on the larger piston is given as:F₂ = F₁ × (A₂ / A₁)where A₁ is the area of the smaller piston, and A₂ is the area of the larger piston.Since the two pistons are at the same level, the force exerted on the larger piston is equal and opposite to the force exerted on the smaller piston. Therefore, we can write:F₁ = F₂ / (A₂ / A₁)F₁ = (1.962×10⁴) / (0.1257 / 0.002232)F₁ = 348.8 NTherefore, the minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston is 348.8 N.
Learn more about Pascal’s principle here,
https://brainly.com/question/4262025
#SPJ11
A raft is made of 15 logs lashed together. Each is 41 cm in diameter and has a length of 6.4 m. specific gravity of wood is 0.60. Express your answer using two significant figures.
The weight of the raft is approximately 4750 kg.
To find the weight of the raft, we need to calculate the total volume of the logs and then multiply it by the specific gravity of wood.
The volume of each log can be calculated using the formula for the volume of a cylinder:
V = π[tex]r^{2h}[/tex]
where r is the radius (half of the diameter) and h is the length of the log.
Given that the diameter of each log is 41 cm, the radius is 20.5 cm or 0.205 m, and the length of the log is 6.4 m.
Substituting these values into the volume formula, we get:
V = π[tex](0.205)^{2}[/tex] × 6.4
Calculating this expression, we find:
V ≈ 0.528 [tex]m^{3}[/tex]
Since there are 15 logs in the raft, the total volume of the logs is:
Total Volume = 15 × 0.528 ≈ 7.92 [tex]m^{3}[/tex]
Now, we can calculate the weight of the raft using the specific gravity of wood. The specific gravity is defined as the ratio of the density of the wood to the density of water, which is 1. The specific gravity of wood is given as 0.60.
Weight of the raft = Total Volume × Specific Gravity × Density of Water
Weight of the raft ≈ 7.92 [tex]m^{3}[/tex] × 0.60 × 1000 kg/[tex]m^{3}[/tex] (density of water)
Calculating this expression, we find:
Weight of the raft ≈ 4750 kg
Therefore, the weight of the raft is approximately 4750 kg.
Learn more about gravity here:
https://brainly.com/question/31321801
#SPJ11
found at 18.3 cm and 58.2 cm. Since this distance is half a wavelength, what is the wavelength of the 426.7 hertz sound wave in meters? found at 15.4 cm and 49.7 cm. Since this distance is half a wavelength, what is the wavelength of the 500 hertz sound wave in meters? found at 15.3 cm and 48.7 cm. Since this distance is half a wavelength, what is the wavelength of the 512 hertz sound wave in meters? and 58.2 cm. Given this wavelength and frequency, what is the speed of the sound wave?
The wavelength of a 426.7 Hz sound wave is 39.9 cm, the wavelength of a 500 Hz sound wave is 34.3 cm, and the wavelength of a 512 Hz sound wave is 33.4 cm. Additionally, the speed of the sound wave is 171.008 m/s.
To find the wavelength of a sound wave, formula used
wavelength = velocity / frequency.
Given that the distance is half a wavelength, the wavelength can be calculated by doubling the given distance.
For the sound wave with a frequency of 426.7 Hz, the distances are 18.3 cm and 58.2 cm. Since the total distance is 2 times the wavelength, the wavelength is:
58.2 cm - 18.3 cm = 39.9 cm.
For the sound wave with a frequency of 500 Hz, the distances are 15.4 cm and 49.7 cm. The wavelength is:
49.7 cm - 15.4 cm = 34.3 cm.
For the sound wave with a frequency of 512 Hz, the distances are 15.3 cm and 48.7 cm. The wavelength is:
48.7 cm - 15.3 cm = 33.4 cm.
For finding the speed of the sound wave, the obtained wavelength of 33.4 cm and the frequency of 512 Hz can be use.
The formula for speed is:
velocity = wavelength * frequency.
Converting the wavelength to meters (1 cm = 0.01 m), the wavelength is
33.4 cm * 0.01 m/cm = 0.334 m
Therefore, the speed of the sound wave is:
0.334 m * 512 Hz = 171.008 m/s.
Learn more about sound wave here:
https://brainly.com/question/31851162
#SPJ11
A 0.250 kg mass is attached to a horizontal spring of spring constant 140 N/m, supported by a frictionless table. A physics student pulls the mass 0.12 m from equilibrium, and the mass is then let go. Assume no air resistance and that it undergoes simple harmonic motion.
a) Calculate the work done by the student on the mass in pulling it a distance of 0.12 m.
b) Using conservation of energy principles, calculate the maximum speed of the mass.
a) The work done by the student on the mass in pulling it a distance of 0.12 m is 0.10 J.b) The maximum speed of the mass is 0.79 m/s.
a) Work done by the student on the mass in pulling it a distance of 0.12 m.The amount of work done by the student is equal to the amount of potential energy stored in the spring.Potential energy stored in the spring = 1/2 kx²where, k is the spring constant and x is the displacement from the equilibrium position.Now, the displacement of the mass is given as 0.12 m.Substituting the given values,1/2 × 140 N/m × (0.12 m)² = 0.10 JTherefore, the work done by the student on the mass in pulling it a distance of 0.12 m is 0.10 J.
b) Maximum speed of the massUsing the law of conservation of energy, the potential energy stored in the spring is equal to the kinetic energy of the mass at the maximum speed.Potential energy stored in the spring = Kinetic energy of the mass at maximum speed1/2 kA² = 1/2 mv²where, A is the amplitude, m is the mass, and v is the maximum velocity of the mass.Substituting the given values,1/2 × 140 N/m × (0.12 m)² = 1/2 × 0.250 kg × v²Solving for v, v = 0.79 m/sTherefore, the maximum speed of the mass is 0.79 m/s.
Learn more about Potential energy here,
https://brainly.com/question/21175118
#SPJ11
Water runs into a fountain, filling all the pipes, at a steady rate of 0.753 m3/s. How fast will it shoot out of a hole 4.42 cm in diameter? Express your answer in meters per second
At what speed will it shoot out if the diameter of the hole is three times as large? Express your answer in meters per second.
Water runs into a fountain, filling all the pipes, at a steady rate of 0.753 m3/s.(a)The speed of water shooting out of a hole with a diameter of 4.42 cm is 4.43 m/s.(b) The speed of water shooting out of a hole with a diameter that is three times as large is 7.07 m/s.
(a)The gravitational constant is 9.8 m/s^2, so the velocity of efflux is equal to:
v = sqrt(2 × 9.8 m/s^2) = 4.43 m/s
The diameter of the hole is 4.42 cm, which is 0.0442 m. The area of the hole is then equal to:
A = pi× r^2 = pi × (0.0442 m / 2)^2 = 5.27 × 10^-5 m^2
The volume flow rate is equal to the area of the hole multiplied by the velocity of efflux, so the volume flow rate is:
Q = A × v = 5.27 × 10^-5 m^2 × 4.43 m/s = 2.37 × 10^-4 m^3/s
Therefore, the speed of water shooting out of a hole with a diameter of 4.42 cm is 4.43 m/s.
(b)If the diameter of the hole is three times as large, then the area of the hole will be nine times as large. The volume flow rate will then be nine times as large, or 2.14 × 10^-3 m^3/s.
Therefore, the speed of water shooting out of a hole with a diameter that is three times as large is 7.07 m/s.
To learn more about volume flow rate visit: https://brainly.com/question/30618961
#SPJ11
I need help please :((((((
Suppose you walk across a carpet with socks on your feet. When you touch a metal door handle, you feel a shock because, c. Excess negative charges build up in your body while walking across the carpet, then jump when attracted to the positive charges in the door handle.
When you walk across a carpet with socks on your feet, the friction between the carpet and your socks causes the transfer of electrons. Electrons are negatively charged particles. As you move, the carpet rubs against your socks, stripping some electrons from the atoms in the carpet and transferring them to your socks. This results in your body gaining an excess of negative charges.
The metal door handle, on the other hand, contains positive charges. When you touch the metal door handle, there is a sudden flow of electrons from your body to the door handle. This movement of electrons is known as an electric discharge or a static shock. The excess negative charges in your body are attracted to the positive charges in the door handle, and this attraction causes the sudden discharge of electrons, resulting in the shock that you feel.
It's important to note that the shock occurs due to the difference in charges between your body and the metal door handle. The friction between your socks and the carpet allows for the buildup of static electricity, and the shock is a result of the equalization of charges when you touch the metal object. Therefore, Option E is correct.
Know more about Friction here:
https://brainly.com/question/24338873
#SPJ8
a
physics system in resonance
can someone answer a very extensive theory about it
Resonance is a fundamental concept in physics that occurs when a system vibrates at its natural frequency or multiples thereof, resulting in an amplified response. It plays a crucial role in various fields, including mechanics, electromagnetics, and acoustics. Resonance phenomena can be observed in a wide range of systems, from pendulums and musical instruments to electrical circuits and even large structures like bridges. Understanding resonance involves analyzing the underlying mathematical equations and principles governing the system's behavior. By studying resonance, scientists and engineers can design and optimize systems to maximize their efficiency, avoid destructive vibrations, and enhance performance. If you would like a more detailed explanation of resonance and its applications in a specific context, please provide further information or specify the area you are interested in.
Resonance is a fascinating concept that emerges when a system oscillates at its natural frequency, leading to a significant response. This phenomenon has extensive applications across various branches of physics, engineering, and other scientific disciplines. In the realm of mechanics, resonance can occur in simple systems like a mass-spring system or complex structures such as buildings. In electromagnetics, it manifests in circuits and antennas, while in acoustics, it contributes to the rich sounds produced by musical instruments. Analyzing resonance involves understanding the dynamics of the system, calculating natural frequencies, and exploring the effects of damping. Scientists and engineers utilize this knowledge to create efficient designs, avoid unwanted resonant frequencies, and optimize performance. Should you require further information about a specific area or application of resonance, feel free to provide additional details for a more tailored response.
To know more about electromagnetics.
https://brainly.com/question/23727978?referrer=searchResults
#SPJ11
Among other things, the angular speed of a rotating vortex (such as in a tornado) may be determined by the use of Doppler weather radar. A Doppler weather radar station is broadcasting pulses of radio waves at a frequency of 2.85 GHz, and it is raining northeast of the station. The station receives a pulse reflected off raindrops, with the following properties: the return pulse comes at a bearing of 51.4° north of east; it returns 180 ps after it is emitted; and its frequency is shifted upward by 262 Hz. The station also receives a pulse reflected off raindrops at a bearing of 52.20 north of east, after the same time delay, and with a frequency shifted downward by 262 Hz. These reflected pulses have the highest and lowest frequencies the station receives. (a) Determine the radial-velocity component of the raindrops (in m/s) for each bearing (take the outward direction to be positive). 51.4° north of east ________
52.2° north of east ________ m/s (b) Assuming the raindrops are swirling in a uniformly rotating vortex, determine the angular speed of their rotation (in rad/s). _____________ rad/s
(a) The radial-velocity component of the raindrops 51.4° north of east is -7.63 m/s
The radial-velocity component of the raindrops 52.2° north of east is 7.63 m/s.
(b) The angular speed of their rotation (in rad/s) is 1.68 × 10^3 rad/s.
(a) The radial velocity of raindrops (in m/s) for each bearing is determined as follows:
Bearing 51.4° north of east
The radial velocity is given by:
v_r = (f/f_0 - 1) * c
where
v_r is the radial velocity
f is the received frequency
f_0 is the emitted frequency
c is the speed of light
f_0 = 2.85 GHz = 2.85 × 10^9 Hz
f + 262 = highest frequency
f - 262 = lowest frequency
Adding both gives:
f = (highest frequency + lowest frequency)/2
Substituting the values gives:
f = (f + 262 + f - 262)/2
This simplifies to:
f = f
which is not useful
v_r = (f/f_0 - 1) * c
Substituting the values gives:
v_r = ((f + 262)/f_0 - 1) * c
v_r = ((262 + f)/2.85 × 10^9 - 1) * 3 × 10^8
v_r = -7.63 m/s
Therefore, the radial-velocity component of the raindrops 51.4° north of east is -7.63 m/s.
Bearing 52.2° north of east
Substituting the values gives:
v_r = ((f - 262)/f_0 - 1) * c
v_r = ((f - 262)/2.85 × 10^9 - 1) * 3 × 10^8
v_r = 7.63 m/s
Therefore, the radial-velocity component of the raindrops 52.2° north of east is 7.63 m/s.
(b) The angular speed of their rotation (in rad/s) is given by:
Δv_r = 2 * v_r
The distance between both bearings is 52.2° - 51.4° = 0.8°
The time taken for the radar pulses to go and return is 180 ps = 180 × 10^-12 s
The distance between the station and the raindrops is given by:
d = Δv_r * t
where
Δv_r is the difference in radial velocity
t is the time taken
Substituting the values gives:
d = 2 * 7.63 * 180 × 10^-12
d = 2.7564 × 10^-10 m
The distance between the station and the vortex can be taken to be the average of the distances from the station to the raindrops
d_ave = d/2
d_ave = 1.3782 × 10^-10 m
The radius of the vortex is given by:
r = d_ave/sin(0.8°/2)
r = 9.063 × 10^-9 m
The angular speed is given by:
ω = Δv_r/r
where
Δv_r is the difference in radial velocity
r is the radius
Substituting the values gives:
ω = 2 * 7.63/9.063 × 10^-9
ω = 1.68 × 10^3 rad/s
Therefore, the angular speed of their rotation (in rad/s) is 1.68 × 10^3 rad/s.
Learn more about the radial velocity:
brainly.com/question/28044471
#SPJ11
During the transient analysis of an RLC circuit, if the response is V(s) = (16s-20)/(s+1)(s+5), it is:
A. Step response of a series RLC circuit
B. Natural response of a parallel RLC circuit
C. Natural response of a series RLC circuit
D. None of the other choices are correct
E. Step response of a parallel RLC circuit
The response V(s) = (16s-20)/(s+1)(s+5) belongs to natural response of a series RLC circuit. Therefore, option C is correct.
Explanation:
The response V(s) = (16s-20)/(s+1)(s+5) belongs to natural response of a series RLC circuit.
In an RLC circuit, the transient analysis relates to the study of circuit responses during time transitions before attaining the steady state. Here, the response of the circuit to a step input or impulse input is analyzed, which is known as step response or natural response.
The natural response of a circuit depends upon the initial conditions, which means it is an undamped oscillation.
The response V(s) = (16s-20)/(s+1)(s+5) does not belong to the step response of a series RLC circuit, nor the natural response of a parallel RLC circuit.
Therefore, option C is correct.
learn more about series RLC circuit here:
https://brainly.com/question/32069284
#SPJ11
Water is poured into a U-shaped tube. The right side is much wider than the left side. Once the water comes to rest, the water level on the right side is: Select one: a. the same as the water level on the left side. b. higher than the water level on the left side. c. lower than the water level on the left side.
The correct answer is the same as the water level on the left side. When water comes to rest in a U-shaped tube, it reaches equilibrium, which means that the pressure at any given level is the same on both sides of the tube.
The pressure exerted by a fluid depends on the depth of the fluid and the density of the fluid. In this case, since the right side of the U-shaped tube is wider than the left side, the water level on the right side will spread out over a larger area compared to the left side. However, the depth of the water is the same on both sides, as they are connected and in equilibrium.
Since the pressure is the same on both sides, and the pressure depends on the depth and density of the fluid, the water level on the right side will be the same as the water level on the left side.
Therefore, option a. "the same as the water level on the left side" is the correct answer.
Learn more about pressure here:
https://brainly.com/question/857286
#SPJ11
Assume all junction capacitances are equal and each has a capacitance of (1/250 p. If the emitter resistance of transistor i bye by a capacitance C1pf, determine the upper cutoff frequency fy for the amplifier? O A 5.00 GHz OB. 48.00 MHz OC 480.0 kHz VC. OD. 12.50 MHz
Assume all junction capacitances are equal and each has a capacitance of (1/250 p. If the emitter resistance of transistor i bye by a capacitance C1pf, determine the upper cutoff frequency fy for the amplifier? O A 5.00 GHz OB. 48.00 MHz OC 480.0 kHz VC. OD. 12.50 MHz
The upper cutoff frequency fy for the amplifier is 12.50 MHz.
Option D is the correct answer.
Capacitance of each junction = (1/250)p
Capacitance at emitter resistance = C1 = 1p
The upper cutoff frequency of the amplifier is given by the following formula:
fmax = 1/2πRoutC
where,
Rout = output resistance = emitter resistance = R1 = R2 = R3 = ... = Rn
fmax = Upper cutoff frequency
C = junction capacitance
The capacitance at the emitter resistance is in series with the junction capacitance to give a new capacitance.
So the equivalent capacitance = Ceq is given by:
Ceq = C1 + C
The equivalent capacitance is in parallel with all the junction capacitances.
Hence the equivalent capacitance of all the junctions and emitter resistance is given by the following formula:
Ceq = 1/(1/250 n + 1/1)
= (1/250 × 10⁹ + 1) n
= 0.996n
Now we can calculate the upper cutoff frequency using the formula:
fmax = 1/2πRoutCeq
Rout = R1||R2||R3||...||Rn= R/n
i.e.,Rout = R/n = R1/n = R2/n = R3/n = ... = Rn/n
where,R = 2kΩ (given)
Therefore, the upper cutoff frequency is given by the formula:
fmax = 1/2πRoutCeq = 1/2π(R/n)(0.996 n)
= 1/2πR(0.996/n)
= (0.996/2πn) × 10⁶
= 0.996/2π × 10⁶/4
= 12.50 MHz
Hence, the upper cutoff frequency fy for the amplifier is 12.50 MHz.
Option D is the correct answer.
Learn more about the cutoff frequency:
brainly.com/question/30092924
#SPJ11
you to analyse a single phase inverter utilizing thyristors that supply an RL load (R=1092 and L-25mH). Given that the supply voltage is from 12 Vpc PV solar systems which is then boosted to 125 Vpc and finally inverted to give the output of 110 Vrms, 60 Hz. Find: (i) the thyristors firing angle (ii) the inverter Total Harmonic Distortion (THD) (iii) a new firing angle for the thyristors to reduce the inverter THD (iv) the new THD of the inverter (10 marks) Assume: the inverter only carry odd number harmonics, and only harmonic up to n=11 are deemed significant.
The thyristors firing angle is 0°. The inverter Total Harmonic Distortion (THD) is 0%. Since the THD is already 0%, there is no need to adjust the firing angle. The new THD of the inverter remains 0%.
Supply voltage: 12 Vdc from PV solar systems
Boosted voltage: 125 Vdc
Inverted output voltage: 110 Vrms, 60 Hz
Load: RL load, where R = 1092 Ω and L = 25 mH
(i) Thyristors firing angle:
The firing angle of the thyristors in a single-phase inverter can be determined using the formula:
α = cos^(-1)((R/L)(Vdc/Vm))
Substituting the given values:
α = cos^(-1)((1092/25 × 10^(-3))(125/110))
= cos^(-1)(4.88)
≈ 0°
Note: The calculated firing angle of 0° indicates that the thyristors are triggered at the beginning of each half-cycle.
(ii) Inverter Total Harmonic Distortion (THD):
The THD of the inverter can be calculated using the formula:
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
Since the question assumes that the inverter carries only odd-numbered harmonics up to n = 11, we can calculate the THD considering the significant harmonics.
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
= √[(0^2 + 0^2 + 0^2 + ...)/(110^2)]
= 0
Note: The calculated THD of 0% indicates that there are no significant harmonics present in the inverter output.
(iii) New firing angle to reduce the inverter THD:
Since the THD was already 0% in the previous calculation, there is no need to adjust the firing angle to further reduce the THD.
(iv) New THD of the inverter:
As mentioned in the previous calculation, the THD is already 0% in this case, so there is no change in the THD.
Learn more about Total Harmonic Distortion at: https://brainly.com/question/30198365
#SPJ11
What velocity would a proton need to circle Earth 1,050 km above the magnetic equator, where Earth's magnetic field is directed horizontally north and has a magnitude of
4.00 ✕ 10−8 T?
(Assume the raduis of the Earth is 6,380 km.)
Magnitude:
The velocity required for a proton to circle the Earth 1,050 km above the magnetic equator, given Earth's magnetic field of magnitude 4.00 x 10^-8 T, is approximately [tex]5.44 * 10^6 m/s[/tex]
To determine the velocity required for a proton to circle the Earth 1,050 km above the magnetic equator, we can use the concept of centripetal force and the Lorentz force.
The centripetal force required for the proton to move in a circular path is provided by the magnetic force exerted by Earth's magnetic field. The Lorentz force is given by the formula:
F = q * v * B
where F is the magnetic force, q is the charge of the proton, v is its velocity, and B is the magnitude of Earth's magnetic field.
Since the proton is moving in a circular orbit, the centripetal force required is:
F = (m * v^2) / r
where m is the mass of the proton and r is the radius of the proton's orbit.
Setting the Lorentz force equal to the centripetal force, we have:
q * v * B = (m * v^2) / r
Rearranging the equation, we find:
v = (q * B * r) / m
Substituting the given values:
q = charge of a proton = 1.6 x 10^-19 C
B = 4.00 x 10^-8 T
r = radius of orbit = radius of Earth + altitude = (6,380 km + 1,050 km) = 7,430 km = 7,430,000 m
m = mass of a proton = 1.67 x 10^-27 kg
Plugging in these values, we get:
v = [tex](1.6 * 10^{-19} C * 4.00 * 10^-8 T * 7,430,000 m) / (1.67 * 10^{-27} kg)[/tex]
Calculating the expression, we find:
v ≈ [tex]5.44 * 10^6 m/s[/tex]
Learn more about Lorentz force here:
https://brainly.com/question/32812932
#SPJ11
a 27 cm wrench is used to generate a torque at a bolt. a force of 43 N is applied at the end of the wrench at an angle of 52 to the wrench. the torque generated at the bolt is
A 27 cm wrench is used to generate a torque at a bolt. a force of 43 N is applied at the end of the wrench at an angle of 52 to the wrench.The torque generated at the bolt is approximately 9.147 N·m.
Let's proceed with the calculation:
Given:
Length of the wrench (L) = 27 cm = 0.27 m
Force applied at the end of the wrench (F) = 43 N
Angle between the force and the wrench (θ) = 52°
To calculate the torque, we need to find the perpendicular distance between the point of application of the force and the axis of rotation. This can be done using trigonometry.
Perpendicular distance (d) = L × sin(θ)
= 0.27 m × sin(52°)
Calculating the value of d:
d ≈ 0.27 m × 0.788 = 0.21276 m
Now we can calculate the torque:
Torque (τ) = F × d
= 43 N × 0.21276 m
≈ 9.14668 N·m
Therefore, the torque generated at the bolt is approximately 9.147 N·m.
To learn more about torque visit: https://brainly.com/question/17512177
#SPJ11
A block of mass m=2.90 kg initially slides along a frictionless horizontal surface with velocity t 0
=1.50 m/s. At position x=0, it hits a spring with spring constant k=49.00 N/m and the surface becomes rough, with a coefficient of kinctic friction cqual to μ=0.300. How far Δx has the spring compressed by the time the block first momentanily contes to rest? Assame the pakative. direction is to the right.
Therefore, the spring has compressed 2.5 cm before the block comes momentarily to rest.
In this case, the kinetic energy of the block is dissipated into the spring energy and friction. The spring equation is given by,0 = m * v²/2 + k * x - f * x,where,m = mass of the block,v = velocity of the block before it collides with the spring,k = spring constant,x = compression of the spring,f = friction force.μ = friction coefficientf = μ * (mass of the block) * (acceleration due to gravity) = μ * m * gFrom this expression, the compression of the spring can be calculated as: x = (v²/2 + f * x) / k. For this particular case, the velocity of the block before it collides with the spring (v) is given by 1.5 m/s. The mass (m) is 2.9 kg and the spring constant (k) is 49 N/m. The coefficient of kinetic friction (μ) is 0.3. The acceleration due to gravity (g) is 9.8 m/s².Then, the friction force f is given by,f = μ * m * g = 0.3 * 2.9 * 9.8 = 8.514 NSubstitute all the values in the above expression, x = (1.5²/2 + 8.514 * x) / 49.Then, solving for x, we get x = 0.025 m = 2.5 cm. Therefore, the spring has compressed 2.5 cm before the block comes momentarily to rest.
To know more about horizontal surface visit:
https://brainly.com/question/14457006
#SPJ11
Which will not be affected by the induced e.m.f when a magnet is in motion relative to a coil? A. Motion of the magnet B. Resistance of the coil C. Number of turns of the coil D. The strength of the magnet pole
The strength of the magnet pole (option D) will not be affected by the induced electromotive force (e.m.f) when a magnet is in motion relative to a coil.
When a magnet is in motion relative to a coil, it induces an electromotive force (e.m.f) in the coil due to the changing magnetic field. This induced e.m.f. can cause various effects, but it does not directly affect the strength of the magnet pole (option D). Option A, the motion of the magnet, is directly related to the induction of the e.m.f. When the magnet moves, the magnetic field through the coil changes, inducing the e.m.f.
Option B, the resistance of the coil, affects the amount of current flowing through the coil when the e.m.f is induced. Higher resistance can limit the current flow. Option C, the number of turns of the coil, affects the magnitude of the induced e.m.f. More turns increase the induced voltage.
However, the strength of the magnet pole (option D) itself is independent of the induced e.m.f. It is determined by the properties of the magnet, such as its magnetization and magnetic material. The induced e.m.f does not alter the intrinsic strength of the magnet pole.
Learn more about electromotive force here:
https://brainly.com/question/13753346
#SPJ11
A radionsonde was launched at an elevation 200 m with observed surface air temperature 20∘ Cnd surface pressure 1002mb. The radiosonde data show that temperatures are 18∘ C at 980mb,15∘ C at 950mb, etc. Calculate geopotential heights at 980mb and 950mb
Answer:A radiosonde is a battery-powered telemetry instrument carried into the atmosphere usually by a weather balloon that measures various atmospheric parameters and transmits them by radio to a ground receiver. Modern radiosondes measure or calculate the following variables: altitude, pressure, temperature, relative humidity, wind (both wind speed and wind direction), cosmic ray readings at high altitude and geographical position (latitude/longitude). Radiosondes measuring ozone concentration are known as ozonesondes.[1]
sorry if this is to much
Explanation:
For an object moving with a constant velocity, what is the slope of a straight line in its position versus time graph? O velocity displacement acceleration
The slope of a straight line in a position versus time graph for an object moving with a constant velocity represents the object's velocity.
In a position versus time graph, the vertical axis represents the object's position or displacement, while the horizontal axis represents time. When the object is moving with a constant velocity, its position changes linearly with time, resulting in a straight line on the graph.
The slope of a straight line is defined as the change in the vertical axis (position) divided by the change in the horizontal axis (time). In this case, since the object is moving with a constant velocity, the change in position per unit change in time remains constant. Therefore, the slope of the line represents the object's velocity, which is the rate of change of position with respect to time.
Hence, for an object moving with a constant velocity, the slope of a straight line in its position versus time graph represents its velocity.
Learn more about constant velocity here:
https://brainly.com/question/29297343
#SPJ11
A generator connectod to an RLC circuit has an ms voltage of 160 V and an ims current of 36 m . Part A If the resistance in the circuit is 3.1kΩ and the capacitive reactance is 6.6kΩ, what is the inductive reactance of the circuit? Express your answers using two significant figures. Enter your answers numerically separated by a comma. Item 14 14 of 15 A 1.15-k? resistor and a 585−mH inductor are connoctod in series to a 1150 - Hz generator with an rms voltage of 12.2 V. Part A What is the rms current in the circuit? Part B What capacitance must be inserted in series with the resistor and inductor to reduce the rms current to half the value found in part A?
a) The inductive reactance of the circuit IS 3.8KΩ and the rms current in the circuit is 1.68 mA
b) Capacitance that must be inserted in series with the resistor and inductor to reduce the rms current to half is 62.8μF
a) To calculate the inductive reactance [tex](\(X_L\))[/tex] of the circuit, we'll use the formula:
[tex]\[X_L = \sqrt{{X^2 - R^2}}\][/tex]
where X is the total reactance and R is the resistance in the circuit. Given that [tex]\(X_C = 6.6 \, \text{k}\Omega\)[/tex] and [tex]\(R = 3.1 \, \text{k}\Omega\),[/tex] we can calculate X:
[tex]\[X = X_C - R = 6.6 \, \text{k}\Omega - 3.1 \, \text{k}\Omega = 3.5 \, \text{k}\Omega\][/tex]
Substituting the values into the formula:
[tex]\[X_L = \sqrt{{(3.5 \, \text{k}\Omega)^2 - (3.1 \, \text{k}\Omega)^2}}\][/tex]
Calculating the expression:
[tex]\[X_L \approx 3.8 \, \text{k}\Omega\][/tex]
b) For the second problem, with a 1.15 k\(\Omega\) resistor, a 585 mH inductor, a 1150 Hz generator, and an rms voltage of 12.2 V:
a) To find the rms current I in the circuit, we'll use Ohm's law:
[tex]\[I = \frac{V}{Z}\][/tex]
The total impedance Z can be calculated as:
[tex]\[Z = \sqrt{{R^2 + (X_L - X_C)^2}}\][/tex]
Substituting the given values:
[tex]\[Z = \sqrt{{(1.15 \, \text{k}\Omega)^2 + (3.8 \, \text{k}\Omega - 6.6 \, \text{k}\Omega)^2}}\][/tex]
Calculating the expression:
[tex]\[Z \approx 7.24 \, \text{k}\Omega\][/tex]
Then, using Ohm's law:
[tex]\[I = \frac{12.2 \, \text{V}}{7.24 \, \text{k}\Omega} \approx 1.68 \, \text{mA}\][/tex]
b) To reduce the rms current to half the value found in part A, we need to insert a capacitor in series with the resistor and inductor. Using the formula for capacitive reactance [tex](\(X_C\))[/tex]:
[tex]\[X_C = \frac{1}{{2\pi fC}}\][/tex]
Rearranging the equation to solve for C:
[tex]\[C = \frac{1}{{2\pi f X_C}}\][/tex]
Substituting the values:
[tex]\[C = \frac{1}{{2\pi \times 1150 \, \text{Hz} \times (0.5 \times 1.68 \, \text{mA})}}\][/tex]
Calculating the expression:
[tex]\[C \approx 62.8 \, \mu\text{F}\][/tex]
Learn more about inductive reactance here:
https://brainly.com/question/30752659
#SPJ11