A compound containing only C, H, and O, was extracted from the bark of the sassafras tree. The combustion of 66.1 mg produced 179 mg of CO2 and 36.7 mg of H2O. The molar mass of the compound was 162 g/mol. Determine its empirical and molecular formulas.

Answers

Answer 1

Therefore, the empirical formula of the compound is C2H2O, and the molecular formula is C8H8O.

To determine the empirical and molecular formulas of the compound, we need to analyze the ratios of the elements present and use the given combustion data.

First, we calculate the moles of carbon dioxide (CO2) and water (H2O) produced in the combustion reaction:

Moles of CO2 = 179 mg / molar mass of CO2 = 179 mg / 44.01 g/mol = 4.07 mmol

Moles of H2O = 36.7 mg / molar mass of H2O = 36.7 mg / 18.02 g/mol = 2.04 mmol

Next, we calculate the moles of carbon (C) and hydrogen (H) in the compound using the stoichiometry of the combustion reaction:

Moles of C = 4.07 mmol

Moles of H = (2 × 2.04 mmol) / 2 = 2.04 mmol

Now, we can determine the empirical formula by dividing the moles of each element by the smallest number of moles (which is 2.04 mmol in this case):

Empirical formula: C2H2O

To find the molecular formula, we compare the empirical formula mass (sum of the atomic masses in the empirical formula) to the given molar mass of the compound (162 g/mol):

Empirical formula mass = (2 × atomic mass of C) + (2 × atomic mass of H) + atomic mass of O

Empirical formula mass = (2 × 12.01 g/mol) + (2 × 1.01 g/mol) + 16.00 g/mol = 42.04 g/mol

To determine the molecular formula, we divide the molar mass of the compound (162 g/mol) by the empirical formula mass (42.04 g/mol):

Molecular formula = (162 g/mol) / (42.04 g/mol) ≈ 3.85

Since the molecular formula must be a whole number, we multiply the empirical formula by 4 (approximately 3.85) to obtain the molecular formula: Molecular formula: C8H8O

To know more about empirical formula,

https://brainly.com/question/28809013

#SPJ11


Related Questions

A mass weighing 64 pounds is attached to a spring whose constant is 21 lb/ft. The medium offers a damping force equal 24 times the instantaneous velocity. The mass is initially released from the equilibrium position with a downward velocity of 9 ft/s. Determine the equation of motion. (Use g = 32 ft/s² for the acceleration due to gravity.)

Answers

The equation of motion for the given scenario is[tex]a = -0.375v - 32.66 ft/s^2[/tex]

To determine the equation of motion for the given scenario, we can start by applying Newton's second law of motion:

F = ma

Where F is the net force acting on the mass m is the mass & a is the acceleration.

In this case, the net force consists of three components: the force due to the spring, the force due to damping, and the force due to gravity.

Force due to the spring:

The force exerted by the spring is given by Hooke's Law:

Fs = -kx

Where Fs is the force exerted by the spring, k is the spring constant, and x is the displacement from the equilibrium position. The negative sign indicates that the force is in the opposite direction of the displacement.

In this case, the displacement x is given by:

[tex]x = 64 lb / (32 ft/s^2) = 2 ft[/tex]

So, the force due to the spring is:

Fs = -21 lb/ft * 2 ft = -42 lb

Force due to damping:

The force due to damping is given by:

Fd = -cv

where Fd is the force due to damping, c is the damping constant, and v is the velocity.

In this case, the damping force is 24 times the instantaneous velocity:

Fd = -24 * v

Force due to gravity:

The force due to gravity is simply the weight of the mass:

Fg = mg

where Fg is the force due to gravity, m is the mass, and g is the acceleration due to gravity.

In this case, the mass is 64 lb, so the force due to gravity is:

[tex]Fg = 64 lb * 32 ft/s^2 = 2048 lb-ft/s^2[/tex]

Now, we can write the equation of motion:

F = ma

Summing up the forces, we have:

Fs + Fd + Fg = ma

Substituting the expressions for each force:

[tex]-42 lb - 24v - 2048 lb·ft/s^2 = 64 lb * a[/tex]

Simplifying:

[tex]-24v - 2090 lb·ft/s^2 = 64 lb * a[/tex]

Dividing by 64 lb to express the acceleration in ft/s²:

[tex]-0.375v - 32.66 ft/s^2 = a[/tex]

Thus, the equation of motion for the given scenario is:

[tex]a = -0.375v - 32.66 ft/s^2[/tex]

Learn more about  Newton's second law of motion:-

https://brainly.com/question/2009830

#SPJ4

Temperature sensitive medication is stored in a refrigerated compartment maintained at -10°C. The medication is contained in a long thick walled cylindrical vessel of inner and outer radii 24 mm and 78 mm, respectively. For optimal storage, the inner wall of the vessel should be 6°C. To achieve this, the engineer decided to wrap a thin electric heater around the outer surface of the cylindrical vessel and maintain the heater temperature at 25°C. If the convective heat transfer coefficient on the outer surface of the heater is 100W/m².K., the contact resistance between the heater and the storage vessel is 0.01 m.K/W, and the thermal conductivity of the storage container material is 10 W/m.K., calculate the heater power per length of the storage vessel. (b) A 0.22 m thick large flat plate electric bus-bar generates heat uniformly at a rate of 0.4 MW/m² due to current flow. The bus-bar is well insulated on the back and the front is exposed to the surroundings at 85°C. The thermal conductivity of the bus-bar material is 40 W/m.K and the heat transfer coefficient between the bar and the surroundings is 450 W/m².K. Calculate the maximum temperature in the bus-bar. 2. A design engineer is contemplating using internal flow or external flow to cool a pipe maintained at 122 °C. The options are to use air at 32 °C in cross flow over the tube at a velocity of 30 m/s. The other option is to use air at 32 °C through the tube with a mean velocity of 30 m/s. The tube is thin-walled with a nominal diameter of 50 mm and flow conditions inside the tube is assumed fully developed. Calculate the heat flux from the tube to the air for the two cases. What would be your advice to the engineer? Explain your reason. For external flow over the pipe in cross-flow conditions: 5/874/3 Nup = 0.3+ 1+ 0.62 Reb/2 Pul/3 [1+(0.4/732187441 ! Red 282.000 For fully developed internal flow conditions: Nup = 0.023 Re45 P0.4

Answers

The heater power per length of the storage vessel can be calculated using the formula:

Heater power per length = (Temperature difference) / [(Thermal resistance of contact) + (Thermal resistance of convection)]

In this case, the temperature difference is the difference between the heater temperature (25°C) and the desired inner wall temperature (6°C), which is 19°C.

The thermal resistance of contact is given as 0.01 m.K/W and the thermal resistance of convection can be calculated using the formula:

Thermal resistance of convection = 1 / (Heat transfer coefficient × Outer surface area)

The outer surface area of the cylindrical vessel can be calculated using the formula:

Outer surface area = 2π × Length × Outer radius

Substituting the given values, we can calculate the thermal resistance of convection.

Once we have the thermal resistance of contact and the thermal resistance of convection, we can substitute these values along with the temperature difference into the formula to calculate the heater power per length of the storage vessel.

b) The maximum temperature in the bus-bar can be calculated using the formula:

Maximum temperature = Front surface temperature + (Heat generation rate / (Heat transfer coefficient × Surface area))

In this case, the front surface temperature is 85°C, the heat generation rate is 0.4 MW/m², the heat transfer coefficient is 450 W/m².K, and the surface area can be calculated using the formula:

Surface area = Length × Width

Substituting the given values, we can calculate the maximum temperature in the bus-bar.

2) To calculate the heat flux from the tube to the air for the two cases, we can use the Nusselt number correlations for external flow over the pipe in cross-flow conditions and fully developed internal flow conditions.

For external flow over the pipe in cross-flow conditions, the Nusselt number correlation is given as:

Nup = 0.3 + 1 + 0.62(Reb/2)(Pul/3)[1 + (0.4/732187441 × Red^282)]

For fully developed internal flow conditions, the Nusselt number correlation is given as:

Nup = 0.023 × Re^0.8 × Pr^0.4

In both cases, the heat flux can be calculated using the formula:

Heat flux = Nusselt number × (Thermal conductivity / Diameter)

Substituting the given values and using the Nusselt number correlations, we can calculate the heat flux for the two cases.

My advice to the engineer would depend on the heat flux values calculated. The engineer should choose the option that provides a higher heat flux, as this indicates a more efficient cooling process. If the heat flux is higher for external flow over the pipe in cross-flow conditions, then the engineer should choose this option. However, if the heat flux is higher for fully developed internal flow conditions, then the engineer should choose this option.

Know more about Thermal resistance here:

https://brainly.com/question/33634341

#SPJ11

4 females? The probability of seiecting at least 4 females is (Type an integet or a simplified fraction.)

Answers

Therefore, the probability of selecting at least 4 females if there are 10 females in the sample is 0.0626 or 626/10,000. Answer: 626/10000.

The total number of females in the sample is not specified, which makes the question difficult to answer. As a result, I am assuming that there are 10 females in the sample. The formula for calculating the probability of choosing at least 4 females is P(X>=4).When X follows a binomial distribution, the formula for calculating P(X>=4) is as follows: P(X>=4) = P(X=4) + P(X=5) + P(X=6) + P(X=7) + P(X=8) + P(X=9) + P(X=10)

Let's find the probability of selecting at least 4 females if there are 10 females in the sample.

P(X=4) = (10 C 4)*(6 C 2)/ (16 C 6)

= 210*15/8008

= 0.0397P(X=5)

= (10 C 5)*(6 C 1)/ (16 C 6)

= 252*6/8008

= 0.0189P(X=6)

= (10 C 6)*(6 C 0)/ (16 C 6)

= 210*1/8008

= 0.0026P(X=7)

= (10 C 7)*(6 C 0)/ (16 C 6)

= 120*1/8008

= 0.0013P(X=8)

= (10 C 8)*(6 C 0)/ (16 C 6)

= 45*1/8008

= 0.0002P(X=9)

= (10 C 9)*(6 C 0)/ (16 C 6)

= 10*1/8008

= 0.000P(X=10)

= (10 C 10)*(6 C 0)/ (16 C 6)

= 1*1/8008

= 0P(X>=4)

= P(X=4) + P(X=5) + P(X=6) + P(X=7) + P(X=8) + P(X=9) + P(X=10)

= 0.0626

Therefore, the probability of selecting at least 4 females if there are 10 females in the sample is 0.0626 or 626/10,000. Answer: 626/10000.

To know more abou probability visit;

brainly.com/question/31828911

#SPJ11

2logx=log64 Solve the equation to find the solution set. Select the correct choice below and, if necessary, fill in the answer box to complete your choice. A. The solution set is (Type an exact answer in simplified form. Use a comma to separate answers as needed.) B. There are infinitely many solutions. C. There is no solution.

Answers

The solution set for the logarithmic equation 2logx = log64 is {8, -8}.

Hence option is a (8,-8 ).

To solve the equation 2logx = log64, we can use the properties of logarithms.

Let's simplify the equation step by step:

Step 1: Apply the power rule of logarithms

The power rule of logarithms states that log(a^b) = b * log(a). We can apply this rule to simplify the equation as follows:

2logx = log64

log(x^2) = log64

Step 2: Set the arguments equal to each other

Since the logarithms on both sides of the equation have the same base (logarithm base 10), we can set their arguments equal to each other:

x^2 = 64

Step 3: Solve for x

Using the property mentioned earlier, we can simplify further:

2logx = 6log2

Now we have two logarithms with the same base. According to the property log(a) = log(b), if a = b, we can equate the exponents:

2x = 6

Dividing both sides of the equation by 2, we get:

x = 3

To find the solutions for x, we take the square root of both sides of the equation:

x = ±√64

x = ±8

Therefore, the solution set for the equation 2logx = log64 is {8, -8}.

The correct choice is A. The solution set is {8, -8}.

Learn more about logarithmic equation from the given link

https://brainly.com/question/30226560

#SPJ11

Math what is the values of x and y

Answers

The values of x and y are 30° and 120° respectively

What is angle at a point?

Angles around a point describes the sum of angles that can be arranged together so that they form a full turn.

Sum of angles at a point is 360°.

Also the sum of angles on a straight line is 180°.

This means that;

x+x+y = 180

2x+y = 180

and;

x +y +30 = 180°

therefore ;

2x +y = x+y +30

2x -x = y-y +30

x = 30°

2(30) +y = 180

y = 180-60

y = 120°

Therefore the values of x and y are 30° and 120° respectively

learn more about angle at a point from

https://brainly.com/question/25716982

#SPJ1

Explain why the frame analysis requires us to disassemble the
members? Why didn't we have to disassemble members when using the
method of joints for truss analysis

Answers

Frame analysis is a technique used to calculate the internal forces or stresses of each member of a structural framework that is subject to external forces. It requires us to disassemble members so that the structural framework can be evaluated in its smaller components or individual parts.

The primary objective of frame analysis is to determine the loads acting on each member. To do so, we must know the precise load distribution along each member, which can only be achieved by breaking the structural framework down into smaller components or individual parts. In the end, it aids us in determining the design's structural integrity, enabling us to avoid potential catastrophes. Frame analysis is especially useful for structures such as buildings, bridges, and other structures that are subjected to numerous and varied loads.While Method of Joints is a technique used to calculate the internal forces or stresses of each member in a truss that is subject to external forces. In this method, each joint is evaluated individually. This method entails cutting each joint in a truss structure and analyzing the forces at the joints. The calculation of the member forces or stresses is then performed in this way. Since the members in a truss are not usually subjected to bending, we may analyze them using the Method of Joints rather than Frame analysis, which is a more complicated and time-consuming method. Consequently, it is not necessary to disassemble members when using the Method of Joints for truss analysis.

To know more about Frame analysis visit:

https://brainly.com/question/7345111

#SPJ11

The temperature is below 2 degrees Fahrenheit.

t < 2

Can someone who took the test answer pls?

Answers

In the context of inequalities and number lines, let's analyze each statement: 1. "A number line going from 0 to 3. A closed circle is at 2. Everything to the left of the circle is shaded."

This represents the inequality t ≤ 2, where t represents a value on the number line. The closed circle at 2 indicates that 2 is included as a valid solution to the inequality.

The shading to the left of the circle represents all values less than or equal to 2, including 2 itself.

2. "A number line going from 0 to 3. An open circle is at 2. Everything to the left of the circle is shaded."

This represents the inequality t < 2, where t represents a value on the number line. The open circle at 2 indicates that 2 is not included as a valid solution to the inequality.

The shading to the left of the circle represents all values strictly less than 2.

3. "A number line going from 0 to 3. An open circle is at 2. Everything to the right of the circle is shaded."

This represents the inequality t > 2, where t represents a value on the number line. The open circle at 2 indicates that 2 is not included as a valid solution to the inequality.

The shading to the right of the circle represents all values greater than 2.

- A closed circle (filled-in circle) represents inclusion.

- An open circle represents exclusion.

- Shading to the left of the circle indicates values less than the given number.

- Shading to the right of the circle indicates values greater than the given number.

For more such questions on inequalities,click on

https://brainly.com/question/25275758

#SPJ8

A UAP (unidentified aerial phenomena) was spotted with an acceleration vector of a = 20i +30j - 60k in m/8^2. It's estimated mass was 1000 kg. Determine the magnitude of the force required to accelerate the object in kN.

Answers

The magnitude of the force required to accelerate the object is 70,000 kN.

In this problem, it is known that a UAP (unidentified aerial phenomena) was spotted with an acceleration vector of [tex]a = 20i +30j - 60k[/tex] in [tex]m/s^2[/tex] and the estimated mass was 1000 kg.

We need to determine the magnitude of the force required to accelerate the object in kN.

Magnitude of force (F) can be calculated by the following formula:

F = ma

Where, m = mass of the object

a = acceleration of the object

So, [tex]F = ma = 1000\  kg \times 20i +30j - 60k m/s^2[/tex]

Now, we will calculate the magnitude of force.

So, [tex]|F| = \sqrt {F^2} = \sqrt{(1000 kg)^2(20i +30j} - 60k m/s^2)^2\\|F| = 1000 \times \sqrt{(400 + 900 + 3600)} kN\\|F| = 1000 \times \sqrt {4900} kN\\|F| = 1000\times 70 kN\\|F| = 70,000 kN[/tex]

Therefore, the magnitude of the force required to accelerate the object is 70,000 kN.

To know more about acceleration, visit:

https://brainly.com/question/2303856

#SPJ11

Indicate whether energy is emitted or absorbed when the following electronic transitions occur in hydrogen: (a) from n=2 to n=6,
(b) from an orbit of radius 4.76 A˚ to one of radius 0.529 A˚
(c) from the n=6 to the n=9 state.

Answers

(a) Transition from n=2 to n=6: Energy is absorbed.

(b) Transition from radius 4.76 Å to radius 0.529 Å: Energy is emitted.

(c) Transition from n=6 to n=9: Energy is emitted.

(a) When an electron transitions from n=2 to n=6 in hydrogen, energy is absorbed. This is because electrons in higher energy levels have greater energy, and when they move to a higher level, they need to absorb energy.

(b) When an electron transitions from an orbit of radius 4.76 Å to one of radius 0.529 Å, energy is emitted. This is because electrons in smaller orbits have lower energy, and when they move to a lower energy level, they release excess energy in the form of electromagnetic radiation.

(c) When an electron transitions from the n=6 to the n=9 state in hydrogen, energy is emitted. Similar to the previous case, electrons moving to lower energy levels release excess energy, resulting in the emission of energy.

In summary:

(a) Energy is absorbed.

(b) Energy is emitted.

(c) Energy is emitted.

To learn more about energy visit : https://brainly.com/question/2003548

#SPJ11

Part 1) Draw the shear diagram for the cantilever beam.
Part 2) Draw the moment diagram for the cantilever beam.

Answers

We draw Part 1) the shear diagram for the cantilever beam. Part 2) the moment diagram for the cantilever beam.

Part 1) To draw the shear diagram for a cantilever beam, follow these steps:

1. Identify the different sections of the beam, including the support and any point loads or reactions.
2. Start at the left end of the beam, where the support is located. Note that the shear force at this point is usually zero.
3. Move along the beam and consider each load or reaction. If there is a point load acting upward, the shear force will decrease. If there is a point load acting downward, the shear force will increase.
4. Plot the shear forces as points on a graph, labeling each point with its corresponding location.
5. Connect the points with straight lines to create the shear diagram.
6. Make sure to include the units (usually in Newtons) and the scale of the diagram.

Part 2) To draw the moment diagram for the cantilever beam, follow these steps:

1. Start at the left end of the beam, where the support is located. Note that the moment at this point is usually zero.
2. Move along the beam and consider each load or reaction. If there is a point load acting upward or downward, it will create a moment. The moment will be positive if it causes clockwise rotation and negative if it causes counterclockwise rotation.
3. Plot the moments as points on a graph, labeling each point with its corresponding location.
4. Connect the points with straight lines to create the moment diagram.
5. Make sure to include the units (usually in Newton-meters or foot-pounds) and the scale of the diagram.

Remember to pay attention to the direction of the forces and moments to ensure accuracy. Practice drawing shear and moment diagrams with different types of loads to improve your understanding.

Learn more about the cantilever beam from the given link-

https://brainly.com/question/27910839

#SPJ11

A 350 mm x 700 mm concrete beam has a simple span of 10 m and prestressed with a parabolic-curved tendon with a maximum sag of 200 mm at midspan. The beam is to carry a total uniform load of 20 kN/m including its own weight. Assume tension stresses as positive and compressive as negative. Determine the following: 1. The effective prestress required for the beam to have no deflection on the given load. 2. The stress in the bottom fiber of the section at midspan for the above condition. 3. The value of the concentrated load to be added at midspan in order that no tension will occur in the section.

Answers

The stress in the bottom fiber of the section at midspan under the given condition is approximately -2.08 MPa.

To determine the required values for the prestressed concrete beam, we can follow the following steps:

Effective Prestress for No Deflection:

The effective prestress required can be calculated using the following equation:

Pe = (5 * w * L^4) / (384 * E * I)

Where:

Pe = Effective prestress

w = Total uniform load including its own weight (20 kN/m)

L = Span length (10 m)

E = Modulus of elasticity of concrete

I = Moment of inertia of the beam's cross-section

Assuming a rectangular cross-section for the beam (350 mm x 700 mm) and using the formula for the moment of inertia of a rectangle:

I = (b * h^3) / 12

Substituting the values:

I = (350 mm * (700 mm)^3) / 12

I = 171,500,000 mm^4

Assuming a modulus of elasticity of concrete (E) as 28,000 MPa (28 GPa), we can calculate the effective prestress:

Pe = (5 * 20 kN/m * (10 m)^4) / (384 * 28,000 MPa * 171,500,000 mm^4)

Pe ≈ 0.305 MPa

Therefore, the effective prestress required for the beam to have no deflection under the given load is approximately 0.305 MPa.

Stress in Bottom Fiber at Midspan:

To find the stress in the bottom fiber of the section at midspan, we can use the following equation for a prestressed beam:

σ = Pe / A - M / Z

Where:

σ = Stress in the bottom fiber at midspan

Pe = Effective prestress (0.305 MPa, as calculated in step 1)

A = Area of the beam's cross-section (350 mm * 700 mm)

M = Bending moment at midspan

Z = Section modulus of the beam's cross-section

Assuming the beam is symmetrically loaded, the bending moment at midspan can be calculated as:

M = (w * L^2) / 8

Substituting the values:

M = (20 kN/m * (10 m)^2) / 8

M = 312.5 kNm

Assuming a rectangular cross-section, the section modulus (Z) can be calculated as:

Z = (b * h^2) / 6

Substituting the values:

Z = (350 mm * (700 mm)^2) / 6

Z = 85,583,333.33 mm^3

Now we can calculate the stress in the bottom fiber at midspan:

σ = (0.305 MPa) / (350 mm * 700 mm) - (312.5 kNm) / (85,583,333.33 mm^3)

σ ≈ -2.08 MPa

Therefore, the stress in the bottom fiber of the section at midspan under the given condition is approximately -2.08 MPa (compressive stress). So, eliminate tension in the section, we need to add a concentrated load at midspan that counteracts the tensile forces.

To more about stress, visit:

https://brainly.com/question/26108464

#SPJ11

Write in detailed the scope and limitation when calculating the friction loass from sudden expansion and contraction of cross section.

Answers

Friction loss due to sudden expansion and contraction of cross-section is calculated to determine the efficiency of piping systems.

When calculating the friction loss from sudden expansion and contraction of cross-section, it is important to consider the scope and limitations of the calculation process.

Scope: The scope of calculating the friction loss from sudden expansion and contraction of cross-section is to determine the amount of energy that is lost due to the change in cross-sectional area. This calculation is essential in determining the efficiency of piping systems and helps in identifying any potential problems that may arise due to the changes in cross-sectional area.

Limitations: There are certain limitations when calculating the friction loss from sudden expansion and contraction of cross-section. These include:1. Inaccuracies in Calculation: Calculating the friction loss from sudden expansion and contraction of cross-section requires a certain degree of accuracy. Any inaccuracy in the calculation process may lead to errors in the final results.2. Neglecting Other Factors: The calculation process only takes into account the frictional losses due to the change in cross-sectional area. Other factors that may contribute to the overall frictional losses, such as roughness of the piping material and fluid properties, are often neglected.

3. Limitations of the Equations: The equations used in calculating the friction loss from sudden expansion and contraction of cross-section have certain limitations. These equations are based on certain assumptions and may not be applicable in all situations.

In summary, the calculation of friction loss due to sudden expansion and contraction of cross-section is an important aspect of determining the efficiency of piping systems.

To know more about friction loss, click here

https://brainly.com/question/28148490

#SPJ11

Can someone help please

Answers

Answer:

A.     3x³ - 24x

Step-by-step explanation:

-12 ÷ -4 = 3

x^4 ÷ x = x³

96 ÷ -4 = -24

x² ÷ x = x

(-12x^4 + 96x²) ÷ -4x = 3x³ - 24x

Please help <3 The grade distribution of the many
students in a geometry class is as follows.
Grade
A B
C D F
Frequency 28 35 56 14 7
Find the probability that a student earns a
grade of A.
P(A) = [?]
Probability
Enter

Answers

To find the probability that a student earns a grade of A, you need to calculate the ratio of the frequency of A grades to the total number of grades.

Given the frequency distribution, we can see that the number of students who earned an A grade is 28. To calculate the probability, divide this number by the total number of students:

P(A) = Number of A grades / Total number of grades

The total number of grades can be obtained by summing up the frequencies of all the grades:

Total number of grades = Frequency of A + Frequency of B + Frequency of C + Frequency of D + Frequency of F

Plugging in the values:

Total number of grades = 28 + 35 + 56 + 14 + 7 = 140

Now, we can calculate the probability:

P(A) = 28 / 140 = 0.2

Therefore, the probability that a student earns a grade of A is 0.2 or 20%.

Answer:

0.2 or 20%

Step-by-step explanation:

The definition of probability is "the number of favorable outcomes over the total number of outcomes". So, to find the probability of someone getting an A, we must:

- Find the Frequency of Someone Getting an A

- Find the Total Frequency of the Distribution

- Divide the Two

As we can see in the table, if we add the Frequencies:

28 + 35 + 56 + 14 + 7 = ?

We get a total of:

140

Looking at the table once more, if we look at the frequency of someone getting an A, we can see that it is:

28

So, if we find the ratio of both values, like so down below:

28 : 140

And simplify it:

28 : 140 = 1 : 5

We can see that the ratio is simplified to 1 : 5, or in decimal and percentage terms, 0.2 and 20%.

SETB: What is the minimum diameter in mm of a solid steel shaft that
will not twist through more than 3º in a 6-m length when subjected
to a torque of 12 kNm? What maximum shearing stress is develo

Answers

The minimum diameter of the solid steel shaft is approximately 42.9 mm.

the minimum diameter of a solid steel shaft can be determined by considering the torque applied and the desired maximum twist angle. To calculate the minimum diameter, we can use the formula:

[tex]τ = (T * L) / (π * d^4 / 32)[/tex]

where:
τ is the maximum shearing stress,
T is the torque (12 kNm),
L is the length of the shaft (6 m),
d is the diameter of the shaft.

We need to rearrange the formula to solve for d:

[tex]d^4 = (32 * T * L) / (π * τ)[/tex]

The shaft does not twist more than 3º, we can set the twist angle to radians:

[tex]θ = (π / 180) * 3[/tex]

Now we can calculate the maximum shearing stress using the formula:

[tex]τ = (T * L) / (π * d^4 / 32)[/tex]

Substituting the given values, we have:

[tex]τ = (12,000 Nm * 6 m) / (π * d^4 / 32)[/tex]

Let's assume the maximum shearing stress is 150 MPa (mega pascals). We can substitute this value into the equation:

[tex]150 MPa = (12,000 Nm * 6 m) / (π * d^4 / 32)[/tex]

Now we can solve for the minimum diameter, d:

[tex]d^4 = (32 * 12,000 Nm * 6 m) / (π * 150 MPa)\\d^4 = (76,800 Nm * m) / (3.1416 * 150 MPa)\\d^4 = 162.787 Nm * m / MPa[/tex]

Taking the fourth root of both sides:

[tex]d = (162.787 Nm * m / MPa)^(1/4)[/tex]

The minimum diameter of the solid steel shaft is approximately 42.9 mm.

Learn more about diameter with the given link,

https://brainly.com/question/28162977

#SPJ11

What is the combination of ground
improvement theory / technique being emphasised as the most
effective in this large scale land reclamation project in view of
the underlying soil profiles?

Answers

The combination of ground improvement theory/ technique being emphasized as the most effective in a large scale land reclamation project in view of the underlying soil profiles is vertical drains with preloading, surcharge, or vacuum consolidation.

To address this issue of a weak soil profile for land reclamation, various ground improvement techniques have been developed.

The purpose of these techniques is to improve the soil's engineering properties by increasing its strength, reducing its compressibility, and increasing its bearing capacity. The most common soil improvement methods are deep mixing, dynamic compaction, surcharge preloading, vertical drains with preloading, and vacuum consolidation.

The soil's permeability and compressibility play an important role in determining the ground improvement technique to be used.

Vertical drains with preloading, surcharge, or vacuum consolidation is the most effective ground improvement technique for this large scale land reclamation project in view of the underlying soil profiles.

The use of vertical drains with preloading is a well-established and commonly used technique for reducing the time required for surcharge consolidation and improving the efficiency of land reclamation.

The use of vacuum consolidation is also effective in improving the soil's compressibility.

To know more about permeability, visit:

https://brainly.com/question/32482559

#SPJ11

For a reaction, ΔrH° = +2112 kJ and ΔrS° = +132.9 J/K. At what
temperature will ΔrG° = 0.00 kJ?

Answers

The temperature at which ΔrG° = 0.00 kJ is 1,596 K.


We know that:

ΔrG° = ΔrH° - TΔrS°

where ΔrG° is the standard free energy change of the reaction, ΔrH° is the standard enthalpy change of the reaction, ΔrS° is the standard entropy change of the reaction, and T is the temperature.

For ΔrG° to equal 0.00 kJ, we can rearrange the equation to solve for T:

T = ΔrH°/ΔrS°

Plugging in the values we have:

T = (2112 kJ)/(132.9 J/K)
T = 1,596 K

Therefore, the temperature at which ΔrG° = 0.00 kJ is 1,596 K.

Learn more about entropy here:

https://brainly.com/question/32484278

#SPJ11

In a survey it was found that 21 persons liked product A, 26 liked product B and 29 liked product C. If 14 people liked products A and B, 12 people liked products C and A, 14 people liked products B and C and 8 liked all the three products. Find
a) The number of people who liked at least one product​

Answers

Answer:

64

Step-by-step explanation:

To find the number of people who liked at least one product, we need to calculate the total number of unique individuals who liked any of the three products.

We can use the principle of inclusion-exclusion to solve this problem. The principle states that:

|A ∪ B ∪ C| = |A| + |B| + |C| - |A ∩ B| - |A ∩ C| - |B ∩ C| + |A ∩ B ∩ C|

Given:

|A| = 21 (number of people who liked product A)

|B| = 26 (number of people who liked product B)

|C| = 29 (number of people who liked product C)

|A ∩ B| = 14 (number of people who liked products A and B)

|A ∩ C| = 12 (number of people who liked products A and C)

|B ∩ C| = 14 (number of people who liked products B and C)

|A ∩ B ∩ C| = 8 (number of people who liked all three products)

Using the formula, we can calculate the number of people who liked at least one product:

|A ∪ B ∪ C| = 21 + 26 + 29 - 14 - 12 - 14 + 8

= 64

Therefore, the number of people who liked at least one product is 64.

Next Problem A road perpendicular to a highway leads to a farmhouse located 10 mile away. An automobile traveling on the highway passes through this intersection at a speed of 70mph. How fast is the distance between the automobile and the farmhouse increasing when the automobile is 7 miles past the intersection of the highway and the road? The distance between the automobile and the farmhouse is increasing at a rate of !!!miles per hour. Next Problem A conical water tank with vertex down has a radius of 11 feet at the top and is 23 feet high. If water flows into the tank at a rate of 10 ft³/min, how fast is the depth of the water increasing when the water is 13 feet deep? The depth of the water is increasing at ft/min. Previous Problem Problem List Next Problem The demand function for a certain item is Q=p²e-(P+4) Remember elasticity is given by the equation E = -40P dp Find E as a function of p. E= ⠀⠀

Answers

The distance between the automobile and the farmhouse is increasing at a rate of approximately 19.2 miles per hour when the automobile is 7 miles past the intersection of the highway and the road.

Determining the rate on increase

Let x and y be the distance the automobile has traveled along the highway from the intersection, and  the distance between the automobile and the farmhouse, respectively.

When the automobile is 7 miles past the intersection, we have x = 7. find the rate of change of y, or dy/dt, at this instant.

Use Pythagorean theorem to relate x and y:

[tex]y^2 = 10^2 + x^2[/tex]

Differentiate both sides with respect to t

[tex]2y (dy/dt) = 0 + 2x (dx/dt)\\dy/dt = (x/y) (dx/dt)[/tex]

[tex]y^2 = 10^2 + 7^2 = 149\\y = \sqrt(149) \approx 12.2 miles.[/tex]

To find dx/dt, differentiate x with respect to time.

Since the automobile is traveling at a constant speed of 70 mph

dx/dt = 70 mph.

Substitute the values

[tex]dy/dt = (x/y) (dx/dt)\\= (7/\sqrt(149)) (70) \approx 19.2 mph[/tex]

Hence, the distance between the automobile and the farmhouse is increasing at a rate of approximately 19.2 miles per hour when the automobile is 7 miles past the intersection of the highway and the road.

Learn more on rate of increase on https://brainly.com/question/12614336

#SPJ4

Determine the amount concentration, in mol/L, of 0.533 moles of sulfuric acid dissolved in a 123 mL solution.

Answers

The amount concentration of 0.533 moles of sulfuric acid dissolved in a 123 mL solution is approximately 4.34 mol/L.

To determine the amount concentration (also known as molarity), we need to calculate the number of moles of sulfuric acid per liter of solution.

Amount of sulfuric acid = 0.533 moles

Volume of solution = 123 mL = 0.123 L

To calculate the amount concentration (molarity), we use the formula:

Molarity (M) = Amount of solute (in moles) / Volume of solution (in liters)

Molarity = 0.533 moles / 0.123 L

Molarity = 4.34 mol/L

Therefore, the amount concentration of 0.533 moles of sulfuric acid dissolved in a 123 mL solution is approximately 4.34 mol/L.

Learn more about concentration at https://brainly.com/question/15583382

#SPJ11

Deriving DNA genes to sequence amino acids (15 points): You have the following sequence of amino acids that starts a desired protein suited for mass production utilizing biomass in a biological reaction: cys tyr met pro ileu a. Based on the sequence of amino acids above, write an appropriate sequence of RNA codons in the table below (5 points) 5 LUGS I can AL ANG VAC AUU b. Based on your answer in part A, write the complementary sequence of DNA bases that pain correctly with each of the RNA codons in order. (5 points) 2-5 「 TET the Teat & AKO Wreng bases wrong buses all of them -2.5 O c. Based on your answer in Párt B, write the bases of the complementary strand of DNA (5 points) Leys Ttyr Pre ilev met G write DNA code (bases that pair with the DNA code in part B

Answers

The RNA codons for the amino acid sequence cys tyr met pro ileu a are:UGU UAC AUG CCA AUC UAA.

The RNA codon sequence, which is UGU UAC AUG CCA AUC UAA.

The complementary sequence of DNA bases that match each of the RNA codons in order are:

UGU: ACAUAC: UGAAUG: CCAUCA: AUGUAA: UUC

The DNA code is TACATGCGGTAATAG.

The bases of the complementary strand of DNA are:

ACGTTACCATTTACA

To know more about RNA codons visit :

brainly.com/question/5824702

#SPJ11

Giving 50 points to whoever gets it right

Answers

The area of a parallelogram is given by the formula:
Area = base * height
In this case, the height of the parallelogram is 2 and the base is 2.5. Therefore, the area of the parallelogram is:
Area = 2.5 * 2 = 5 square units.

Answer:  10 sq in

Step-by-step explanation:

Area = base x height

        = 5 in x 2 in

        = 10 sq in

La función f(x) = 68(1.3) * representa la posible población de ardillas en un parque dentro de x años. Cada año , la cantidad de ardillas esperada de ardillas es cuantas veces mas que el año anterior?​

Answers

The expected number of squirrels in the park increases by a factor of 1.3 each year.

The given function, f(x) = 68(1.3)^x, represents the possible population of squirrels in a park after x years. To determine how many times the expected number of squirrels increases each year, we can compare the population at consecutive years.

Let's consider two consecutive years, x and x+1. The population at year x is given by f(x) = 68(1.3)^x, and the population at year x+1 is given by f(x+1) = 68(1.3)^(x+1).

To find how many times the population increases, we can divide f(x+1) by f(x):

f(x+1)/f(x) = [68(1.3)^(x+1)] / [68(1.3)^x]

           = (1.3)^(x+1 - x)

           = 1.3

Therefore, the expected number of squirrels in the park increases by a factor of 1.3 each year. In other words, the population of squirrels is expected to grow by 1.3 times every year.

For more questions on factor, click on:

https://brainly.com/question/24351176

#SPJ8

What is the optimal solution for the following problem?
Maximize
P = 3x + 15y
subject to
2x + 6y ≤ 12
5x + 2y ≤ 10
and x = 0, y ≥ 0.
(x, y) = (2, 1)
(x, y) = (2, 0)
(x, y) = (1, 5)
(x, y) = (3,0)
(x, y) = (0,3)

Answers

Among the given feasible points, the optimal solution that maximizes the objective function P = 3x + 15y is (x, y) = (1, 5), which results in the maximum value of P = 78.

To find the optimal solution for the given problem, we need to maximize the objective function P = 3x + 15y subject to the given constraints.

The constraints are as follows:

2x + 6y ≤ 12

5x + 2y ≤ 10

x = 0 (non-negativity constraint for x)

y ≥ 0 (non-negativity constraint for y)

We can solve this problem using linear programming techniques. We will evaluate the objective function at each feasible point and find the point that maximizes the objective function.

Let's evaluate the objective function P = 3x + 15y at each feasible point:

(x, y) = (2, 1)

P = 3(2) + 15(1) = 6 + 15 = 21

(x, y) = (2, 0)

P = 3(2) + 15(0) = 6 + 0 = 6

(x, y) = (1, 5)

P = 3(1) + 15(5) = 3 + 75 = 78

(x, y) = (3, 0)

P = 3(3) + 15(0) = 9 + 0 = 9

(x, y) = (0, 3)

P = 3(0) + 15(3) = 0 + 45 = 45

From the above evaluations, we can see that the maximum value of P is 78, which occurs at (x, y) = (1, 5).

Therefore, the optimal solution for the given problem is (x, y) = (1, 5) with P = 78.

Learn more about optimal solution here:

https://brainly.com/question/14914110

#SPJ11

Step 1: –10 + 8x < 6x – 4
Step 2: –10 < –2x – 4
Step 3: –6 < –2x
Step 4: ________

What is the final step in solving the inequality –2(5 – 4x) < 6x – 4?

x < –3
x > –3
x < 3
x > 3

Answers

Hello!

-10 + 8x < 6x - 4

-10 < -2x - 4

-6 < -2x

3 < x

-2(5 - 4x) < 6x - 4

-10 + 8x < 6x - 4

8x - 6x < -4 + 10

2x < 6

x < 3

how
does alkyl structure affect SN1 reaction

Answers

The tertiary alkyl halide is more responsive towards SN1 compared to auxiliary and essential alkyl halides particular. Methyl halides nearly never respond by means of an SN1 mechanism.

What is the alkyl structure

The alkyl structure plays a critical part in deciding the rate and result of SN1 (Substitution Nucleophilic Unimolecular) responses.

In SN1 responses, a nucleophilic substitution happens in two steps: the introductory ionization or separation of the substrate, shaping a carbocation middle, taken after by the assault of a nucleophile on the carbocation.

So, the rate of SN1 reactions is one that follows the pattern of: tertiary > secondary > primary > methyl alkyl halides

Read more about alkyl structure  here:

https://brainly.com/question/31502689

#SPJ4

Mr. Ganzon has a newly constructed 4 story Commercial Building located at Isabela City, Basilan. The building has a total fixture consist of the following; water closet (WC)=130, Urinal (UR)= 30, Shower head (SHO)= 12, Lavatories (LAV)= 100, and service sinks (SS)= 27. Given the following fixture demand (WC=8.0, UR= 4.0, SHO=2.0, LAV=1.0, SS=3.0)
a. Using UPC, determine the total water supply fixture units (WSFU) for the water closet
b. Using UPC, determine the total water supply fixture units (WSFU) for the urinal
c. Using UPC, determine the total water supply fixture units (WSFU) for shower head
d. Using UPC, determine the total water supply fixture units (WSFU) for the lavatories
e. Using UPC, determine the total water supply fixture units (WSFU) for the service sink
f. Calculate the total fixture units of the building demand

Answers

a. The first step is to determine the Water Supply Fixture Unit (WSFU) for the water closet (WC) using the Uniform Plumbing Code (UPC). The UPC provides a standard value for each type of fixture based on its water demand. For a water closet, the UPC assigns a value of 8.0 WSFU.

b. Next, we can determine the WSFU for the urinal (UR). According to the UPC, a urinal has a value of 4.0 WSFU.

c. Moving on to the shower head (SHO), the UPC assigns a value of 2.0 WSFU for each shower head.

d. For lavatories (LAV), the UPC assigns a value of 1.0 WSFU per lavatory.

e. Lastly, for service sinks (SS), the UPC assigns a value of 3.0 WSFU per service sink.

f. To calculate the total fixture units of the building demand, we need to multiply the quantity of each fixture type by its corresponding WSFU value, and then sum up the results.

Here are the calculations:

WC: 130 fixtures x 8.0 WSFU = 1040.0 WSFU
UR: 30 fixtures x 4.0 WSFU = 120.0 WSFU
SHO: 12 fixtures x 2.0 WSFU = 24.0 WSFU
LAV: 100 fixtures x 1.0 WSFU = 100.0 WSFU
SS: 27 fixtures x 3.0 WSFU = 81.0 WSFU

Adding up these results, we have a total of 1365.0 WSFU for the building demand.

Therefore, the total fixture units of the building demand is 1365.0 WSFU.

To learn more about lavatory

https://brainly.com/question/14336634

#SPJ11

If a1​,a2​,…..an​ is a complete set of residues modulo n and g.c.d. (a,n)=1, then show that aa1​,aa2​,…..aan​ is also a complete set of residues modulo n. 6. Solve the linear congruence 25x≡15(mod29).

Answers

The linear congruence 25x ≡ 15 (mod 29) is x ≡ 9 (mod 29).

Given that a₁, a₂, …, aₙ is a complete set of residues modulo n and g.c.d. (a, n) = 1

Suppose that, if possible, aaᵢ ≡ aaⱼ (mod n) for some i and j such that

1 ≤ i < j ≤ n⇒ a * aᵢ ≡ a * aⱼ (mod n)⇒ a * (aⱼ - aᵢ) ≡ 0 (mod n)

Since g.c.d. (a, n) = 1,

then g.c.d. (a * (aⱼ - aᵢ), n) = g.c.d. (aⱼ - aᵢ, n) = d(d|n)

Since aᵢ and aⱼ are distinct residues, so they are also co-prime with n.

Thus, their difference (aⱼ - aᵢ) is also co-prime with n.

So, d = 1 and aⱼ ≡ aᵢ (mod n), which is a contradiction.

Hence aa₁, aa₂, …, aa n must be a complete set of residues modulo n. Q:

Solve the linear congruence 25x ≡ 15 (mod 29)

Let us find the multiplicative inverse of 25 in mod 29 by Euclid's Algorithm.

29 = 25 * 1 + 429 = 4 * 7 + 125 = 5 * 4 + 525 = 1 * 5 + 0

Hence, the multiplicative inverse of 25 in mod 29 is 5.

Now, multiply both sides of the equation by the inverse of 25 (which is 5) to get,

5(25x) ≡ 5(15) (mod 29)⇒ 125x ≡ 75 (mod 29)⇒ 2x ≡ 17 (mod 29)

Now, the congruence 2x ≡ 17 (mod 29) isx ≡ 9 (mod 29)

Therefore, the linear congruence 25x ≡ 15 (mod 29) is x ≡ 9 (mod 29).

To know more about linear congruence visit:

https://brainly.com/question/32700407

#SPJ11

On Babylonian tablet YBC 4652, a problem is given that translates to this equation:

X + + x plus StartFraction x Over 7 EndFraction plus StartFraction 1 Over 11 EndFraction left-parenthesis x plus StartFraction x Over 7 EndFraction right-parenthesis equals 60.(x + ) = 60
What is the solution to the equation?

x = 48.125
x = 52.5
x = 60.125
x = 77

Answers

The solution to the equation is x = 48.125.

To solve the equation represented by the Babylonian tablet YBC 4652, let's break down the given equation and solve for x.

The equation is:

x + (x + x/7 + 1/11)(x + x/7) = 60

We'll simplify it step by step:

First, distribute the terms:

x + (x + x/7 + 1/11)(x + x/7) = 60

x + (x^2 + (2x/7) + (1/11)(x) + (1/7)(x/7)) = 60

x + (x^2 + (2x/7) + (x/11) + (1/49)x) = 60

Combine like terms:

x + x^2 + (2x/7) + (x/11) + (1/49)x = 60

Next, find a common denominator and add the fractions:

(49x + 7x^2 + 22x + 4x + x^2) / (49*7) = 60

(7x^2 + x^2 + 49x + 22x + 4x) / 343 = 60

8x^2 + 75x / 343 = 60

Now, multiply both sides by 343 to get rid of the denominator:

8x^2 + 75x = 343 * 60

8x^2 + 75x = 20580

Rearrange the equation in standard quadratic form:

8x^2 + 75x - 20580 = 0

To solve this quadratic equation, we can either factor it or use the quadratic formula. Factoring may not be easy, so let's use the quadratic formula:

x = (-b ± √(b^2 - 4ac)) / (2a)

Plugging in the values:

x = (-75 ± √(75^2 - 4 * 8 * -20580)) / (2 * 8)

x = (-75 ± √(5625 + 662400)) / 16

x = (-75 ± √667025) / 16

Now, calculate the square root and simplify:

x = (-75 ± 817.35) / 16

x = (-75 + 817.35) / 16 or x = (-75 - 817.35) / 16

x = 742.35 / 16 or x = -892.35 / 16

x ≈ 48.125 or x ≈ -55.772

Since the value of x cannot be negative in this context, the approximate solution to the equation is:

x ≈ 48.125

For more such questions on solution,click on

https://brainly.com/question/24644930

#SPJ8

Answer:

The correct answer is A. X= 48.125

Step-by-step explanation:

Calculate length of d

Answers

The value of the missing length d using law of sines is: 28.97 m

How use law of sines and cosines?

If only one of these is missing, the law of cosines can be used.

3 sides and 1 angle. So if the known properties of a triangle are SSS (side-side-side) or SAS (side-angle-side), then this law applies.

If you want the ratio of the sine of an angle and its inverse to be equal, you can use the law of sine. This can be used if the triangle's known properties are ASA (angle-side-angle) or SAS.

Using law of sines, we ca find the missing length d as:

d/sin 43 = 38.5/sin 65

d = (38.5 * sin 43)/sin 65

d = 28.97 m

Read more about law of sines and cosines at: https://brainly.com/question/10254615

#SPJ1

Other Questions
What properties of legumes (beans) could influence the growth ofplants around them? Did you find evidence of any beneficial growtheffects of legumes on your wheat plants?Give a reference as well. Select an assertion method that checks if a string is not asubstring of another string.a.assertIsNotb.assertFalsec.assertNotInd.assertNotEqual Question 3: 20 marks in total What are the implications of the outcomes of taste aversion learning experiments for our understanding of classical conditioning? In your answer be sure to outline how each differs from the other as well as how these differences provide insights into the mechanisms underpinning learning based on classical conditioning. Part 2 - consider the result of previous circuit is the type of operation you will use. Insert using keyboard or manually two numbers to be calculated (add, sub, multiply or compare). You should use sequential circuit comparator. You will use 8-bit unsigned numbers. a) Design 8-bit adder-subtractor that add/sub two input numbers. (1 marks) b) Design 4-bit multiplier that multiply two input numbers (It can use the lower 4 bits of each of the binary numbers). c) Design and implement sequential circuit that compares two input numbers. 1. A reset signal resets the comparator to its initial state. Reset is required before starting a new comparison. 2. Two outputs: any value you specify as (Greater Than) and any value you specify as (Less Than) (you should determine the value on the beginning of your answer) 3. show state diagram, state table, k-map simplification, and circuit diagram with used flipflop. d) Implement the calculation and show in table at least 5 results for each operation. Write your observation. Solve the recurrence :a) T(n) = T(n 1) + n T(1) = 1b) T(n) = T(n/2) + 1 T(1) = 1c) T(n) = 2T(n/2) + n T(1) = 1 Draw a GG-LL graph to explain how economic dynamics may have changed so that it is more costly to Greece to stay as a member of the Euro. According to the article by Bolino and colleagues (2013) there is empirical evidence for the following finding: OCB does not contribute to higher levels of work-conflict family among engaged employees O Employees who engage in individual initiative experienced increased levels of work-family conflict O OCB contributes to higher levels of work-conflict family especially for conscientious employees O OCB's are equally conducive to work-family conflict for both women and men can anyone help me fix my C++ program to get it to run properly? Thank you./*** Program Name: cis6Spring2022Hw4Ex1.c* Discussion: HW #4 Ex 1* Written By: John Smith* Date: 2022/05/16*/// Headers/Include Files#include // Function Prototypesint displayClassInfoYourName(int n);// Application Driverint main() {printf("\nCIS 6 - Introduction to programming (Using C++)""\n""\n""\n""\n Information--""\n\tAssignment: \t\t\tHW #4 Exercise #1""\n\tImplemented by: \t\t\t\John Smitht\t""\n\tSubmitted Date:\t\t\t2022/05/16""\n\tCurrent Number of LEB available: 2""\n\tAllowed Number of LEB Used:\t1""\n\tRemaining Number of LEB:\t1");return 0;}void displayAllDigitYourName(int n){int i, ld, even = 0, odd = 0, c = 0, list[100];if (n == 0)printf("The given value is ZERO\n\n");else{{if (n < 0)printf("%d is a negative number\n\n", n);n *= -1;else (n > 0)printf("%d is a postive number\n\n", n);}}while (n > 0){ld = n % 10;list[c] = ld;n = n / 10;c; ++;}printf("There is/are %d digit(s).\n\n", c);printf("The digit(s) would be \n");for (i = 0; i < c; i++){printf("%d\n", list[i]);if (list[i] % 2 == 0)even++;elseodd++;}printf("\n\nThere is/are %d even digit(s)\n", even);for (i = 0; i < c; i++){if (list[i] % 2 == 0)printf("%d\n", list[i]);}printf("\n\nThere is/are %d odd digit(s)\n", odd);for (i = 0; i < c; i++);{if (list[i] % 2 != 0);printf("%d\n", list[i]);}}// Function Definitionsint main() {void displayClassInfoJohnSmith();int ch, n;do{(printf("****************");while} What is -2( 3x + 12y - 5 - 17x - 16y + 4 )simplified?-40x + 8y + 228x + 8y + 2 28x + 6y + 2-28x - 8y + 2 1. For each of the following, write a single statement that performs the specified task. Assume that long variables value1 and value2 have been declared and value1 has been initialized to 200000.a) Declare the variable longPtr to be a pointer to an object of type long.b) Assign the address of variable value1 to pointer variable longPtr.c) Display the value of the object pointed to by longPtr.d) Assign the value of the object pointed to by longPtr to variable value2.e) Display the value of value2.f) Display the address of value1.g) Display the address stored in longPtr. Is the address displayed the same as value1s?c++ 3. The unique way that employees interact with each other and their customers. Also, the personality of the company: A. Shopper expectations B. Brand promiseC. Distribution mentality D. Company culture List and explain Nielsen's ten heuristics. Provide an example (usability error) currently on the web for each heuristic. You are allowed to use different web sites for sure. Use screenshots to clarify your answer. Noticing interaction problems even in our daily routine is very common. Suggest some solutions to overcome each identified usability problem. What are the values of A, Rin, Rout, and A L amplifier if R = 2MQ, R = 100kQ, R = 2kQ, and gm = 0 and r = 00. Rin Ri Rout Vi +1 H RG 2M ww .RL 2k -1 i i, = 10mS. Assume for the following No What is the central idea of ''A Mission at Midnight''?A. The Rolling Quads made changes to streets without permission.B. The Rolling Quads told politicians that they needed more curb cuts.C. The Rolling Quads fought for equality for people in wheelchairs. Q1. WHAT IS COVERLETTER?Q2. WHAT ARE THECOMPONENTS OFCOVER LETTER? The velocity of the freefalling parachutist with linear drag is given byv(t)=gm/c(1e^(c/m)^t)Given g=9.8 m/s2,m=68 kg, and c=12 kg/m3, how far does the parachutist travel from t=0 s to t=10 s calculated using (a) analytical integration, (b) 2-segments of Trapezoidal rule, and (c) 1-segment of Simpson's 1/3 rule. Compare your numerical results to the analytical solution. a This program is a simple demo of DFA. A DFA with following characteristics: No of states is 4: 90, 91, 92, 93, and q4 No of symbols is 2: 'a' and 'b' Start state is go The DFA accepts any string that ends with either aa or bb Input string is read from a file. File name is provided by user as command line argument. Input string MUST have a $ symbol as sentinel value in the end. Hint: You need to draw the DFA and its corresponding state table. From state table you can implement your logic by using goto statements. If an invalid input symbol is received the program should terminate with an appropriate message. Sample Run $ gee labb.c -o labo $ ./labb infile Input string is: abb$ State transitions are shown below: Received a on state go - Moving to state : Received b on state qi - Moving to state q3 Received bon state q3 Moving to state 4 End of string. String accepted 4. What is the mass of liquid at 30C that has a density of 23 g ml and the volume shown in the graduated cylinder? (Show your work to receive credit.) Sound and its management contribute to the architectural experience. However, there is a misconception on how sound is produced to begin with. Explain this misconception and narrate how managing the nature of sounds nature in the built environment would be far easier once air/wind flow is controlled Which statement best describes the common experience og indigenous people's with the american landscape?