a) The actual water phase mass flux, Gₓ is 0.148 kg m⁻²s⁻¹.
b) The mole fraction of acetone in the exit water stream is 0.000355.
c) The value of Hₓ, the height of the packing is 0.214 meters.
d) The height of the packing is 0.214 meters.
To solve this problem, we'll use the concept of mass transfer in a packed tower. Let's calculate the required values step by step:
(a) The actual water phase mass flux, Gₓ:
We know that Gᵧ is the gas phase mass flux, and the ratio of liquid to gas phase mass flux is given by Gₓ/Gᵧ = kᵧa / kₓa. Plugging in the given values, we have
Gₓ/0.82 = 0.048 / 0.266
Solving for Gₓ, we find Gₓ = 0.82 * (0.048 / 0.266) = 0.148 kg m⁻²s⁻¹.
(b) The mole fraction of acetone in the exit water stream:
Using the equilibrium relationship y* = 2.53x, we can relate the mole fractions of acetone in the gas phase (y) and liquid phase (x). Since we're removing 95% of acetone, the mole fraction of acetone in the exit gas stream is
0.018 * (1 - 0.95) = 0.0009
Using the equilibrium relationship, we find x = 0.0009 / 2.53 = 0.000355 for the exit water stream.
(c) Hₓ, the height of the packing:
Hₓ can be calculated using the formula Hₓ = (Gₓ / kₓa) * (y* - y). Substituting the known values, we have
Hₓ = (0.148 / 0.266) * (2.53 * 0.000355 - 0.0009) = 0.214 meters.
(d) The height of the packing:
The height of the packing is typically determined by factors such as desired separation efficiency, pressure drop, and other design considerations. In this case, we've only calculated Hₓ, which represents the height required for the given separation efficiency. Additional factors may need to be considered to determine the overall height of the packing in a practical design.
In summary, we've calculated the actual water phase mass flux, the mole fraction of acetone in the exit water stream, and the height of the packing required to achieve 95% removal of acetone. These values provide important insights for designing a packed tower for acetone removal using water as the solvent.
To learn more about gas flow click on,
https://brainly.com/question/33223259
#SPJ4
(x-3)^2+(y-5)^2=4
What is it’s corresponding center and radius? Need asap
Answer: Centre=(3,5)
Radius = 2
Step-by-step explanation:
By comparing it with the standard form equation of a circle,
[tex](x - h)^2 + (y - k)^2 = r^2[/tex]
therefore the centre of the circle: (h, k) = (3, 5)
radius = [tex]\sqrt[]{r^2}[/tex]
Use dimensional analysis to solve the following problem. Convert 1.45 x 10^14 ng to kg
1.45 x 10^14 ng is equivalent to 1.45 x 10^5 kg.
To convert 1.45 x 10^14 ng to kg using dimensional analysis, we'll use the fact that 1 kg is equal to 1,000,000,000 ng (1 billion ng). Here's how we can set up the conversion:
1.45 x 10^14 ng * (1 kg / 1,000,000,000 ng)
Let's simplify the expression by canceling out the ng units:
1.45 x 10^14 * 1 kg / 1,000,000,000
Now, let's calculate the value:
1.45 x 10^14 / 1,000,000,000 = 1.45 x 10^5
To know more about dimensional visit:
brainly.com/question/17967616
#SPJ11
Consider the following reversible elementary reaction liquid phase that takes place in a CSTR: 2A <- ->B. The equilibrium constant Kc is 2.1 L/mol at 400 K. Inlet information is: FA0 = 5 mol/min, FB0 = 0.5 mol/min, FI0 = 1 mol/min. HA {TR} = -250 kJ/mol, HB {TR} = -450 kJ/mol, HI {TR} = -1300 kJ/mol, TR = 298.15 K. CpA = 34 J/molK, . CpB = 33 J/molK, . CpI = 30 J/molK. Calculate the adiabatic equilibrium conversion and temperature for this reaction. Evaluate KC and Xe at 400K, 450K and 500K. Use an adiabatic energy balance to calculate Temperature at energy balance at the following conversions: 0, 0.20 and 0.40
The adiabatic equilibrium conversion for the reversible reaction 2A <-> B can be calculated using the equilibrium constant Kc and the inlet information. The equilibrium constant Kc is given as 2.1 L/mol at 400 K.
To calculate the adiabatic equilibrium conversion, we need to determine the extent of the reaction at equilibrium. This can be done by comparing the initial and equilibrium concentrations of the reactants and products. In this case, we have FA0 = 5 mol/min and FB0 = 0.5 mol/min as the initial concentrations, and we need to find the equilibrium concentrations, FAe and FBe.
The equilibrium conversion Xe can be calculated using the equation:
Xe = (FA0 - FAe) / FA0
To find the equilibrium concentrations, we can use the equation:
Kc = (FBe / (FAe)^2)
By rearranging the equation, we can solve for FBe in terms of FAe:
FBe = Kc * (FAe)^2
Substituting the values of Kc and FAe, we can calculate FBe. Then, we can use the equation for Xe to calculate the adiabatic equilibrium conversion.
To calculate the temperature at energy balance, we need to use the adiabatic energy balance equation, which states that the change in enthalpy is equal to zero:
ΔH = ΣνiHi = 0
where ΔH is the change in enthalpy, νi is the stoichiometric coefficient, and Hi is the enthalpy of each species. By substituting the given values, we can solve for the temperature at energy balance. We can repeat this calculation for different conversions (0, 0.20, and 0.40) to find the corresponding temperatures.
Know more about adiabatic here:
https://brainly.com/question/33498093
#SPJ11
A 0.724M solution of HNO_3 has a pH of 0.559 in solution. What is the % ionization?
To calculate the percent ionization of a solution, we need to determine the concentration of the ionized species and the initial concentration of the acid. In this case, the acid is HNO3, and we know the initial concentration is 0.724 M.
The pH of the solution is given as 0.559. The pH is related to the concentration of H+ ions in the solution. We can use the equation pH = -log[H+], rearrange it to [H+] = 10^(-pH), and then substitute the given pH value to find the concentration of H+ ions.
[H+] = 10^(-0.559)
[H+] = 0.267 M
Now we can calculate the percent ionization using the formula:
% Ionization = ([H+] / Initial concentration of acid) * 100
% Ionization = (0.267 M / 0.724 M) * 100
% Ionization = 36.8%
Therefore, the percent ionization of the 0.724 M HNO3 solution with a pH of 0.559 is approximately 36.8%.
In summary, we calculate the percent ionization by dividing the concentration of H+ ions by the initial concentration of the acid and multiplying by 100. In this case, with a pH of 0.559, the concentration of H+ ions is 0.267 M, and the percent ionization is approximately 36.8%.
Learn more about ionization from the given link:
https://brainly.com/question/28385102
#SPJ11
For the matrix A below, find a nonzero vector in Nul A and a nonzero vector in Col A A = 125 013-7 0 A nonzero vector in Nul A is (Type an integer or decimal for each matrix element) A nonzero vector in Col A is (Type an integer or decimal for each matrix element)
A nonzero vector in Col A is: b(x₁, x₂, x₃) = (0, 1, 0) So, a nonzero vector in Null A is (13/7, -3, 1), and a nonzero vector in Col A is (0, 1, 0).
To find a nonzero vector in the nullspace (Nul A) and a nonzero vector in the column space (Col A) of matrix A, we first need to understand the properties of the given matrix.
The matrix A is:
[tex]A=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right][/tex]
To find a nonzero vector in the nullspace (Nul A), we need to find a vector x such that Ax = 0, where 0 is the zero vector.
Setting up the equation Ax = 0, we have:
[tex]A\times x=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right]*\ \begin{bmatrix}x_1 \\x_2 \\x_3\end{bmatrix}[/tex]
Expanding the matrix multiplication, we get:
x₁ + 2x₂ + 5x₃ = 0 --------- (1)
x₂ + 3x₃ = 0 --------- (2)
-7x₁ + 13x₃ = 0 --------- (3)
To find a nonzero solution for x, we can set x₃ = 1 and solve the system of equations.
Let's set x₃ = 1 and solve for x₁ and x₂.
Using Equation 2:
x₂ + 3(1) = 0
x₂ + 3 = 0
x₂ = -3
Using Equation 3:
-7x₁ + 13(1) = 0
-7x₁ + 13 = 0
-7x₁ = -13
x₁ = 13/7
Therefore, a nonzero vector in Nul A is:
(x₁, x₂, x₃) = (13/7, -3, 1)
To find a nonzero vector in the column space (Col A), we need to find a vector b such that there exists a vector x satisfying Ax = b.
We can choose a vector b that is in the column space of A. For example, let's choose b as the second column of A:
[tex]b=\begin{bmatrix}2 \\1 \\0\end{bmatrix}[/tex]
Now, we need to find a vector x such that Ax = b.
Setting up the equation Ax = b, we have:
[tex]A\times x=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right]*\ \begin{bmatrix}x_1 \\x_2 \\x_3\end{bmatrix}\ =\begin{bmatrix}2 \\1\\0\end{bmatrix}[/tex]
Expanding the matrix multiplication, we get:
x₁ + 2x₂ + 5x₃ = 2 ----------- (4)
x₂ + 3x₃ = 1 ----------- (5)
-7x₁ + 13x₃ = 0 ----------- (6)
We can solve this system of equations to find the values of x₁, x₂, and x₃. However, we can observe that Equation 6 already implies that x₁ = 0, since -7x₁ + 13x₃ = 0.
Using Equation 4:
0 + 2x₂ + 5x₃ = 2
2x₂ + 5x₃ = 2
Using Equation 5:
x₂ + 3x₃ = 1
We can solve these two equations to find the values of x₂ and x₃.
From Equation 5, we can rewrite it as:
x₂ = 1 - 3x₃
Substituting this value of x₂ in
Equation 4, we get:
2(1 - 3x₃) + 5x₃ = 2
2 - 6x₃ + 5x₃ = 2
-x₃ = 0
x₃ = 0
Substituting the value of x₃ = 0 in x₂ = 1 - 3x₃, we get:
x₂ = 1 - 3(0)
x₂ = 1
Therefore, a nonzero vector in Col A is:
(x₁, x₂, x₃) = (0, 1, 0)
So, a nonzero vector in Nul A is (13/7, -3, 1), and a nonzero vector in Col A is (0, 1, 0).
To know more about matrix visit:
https://brainly.com/question/33840317
#SPJ11
Solve equation then round your solution to two decimal places
the solution of the equation is answer is x=4.00
To solve the equation, follow the following steps:
1: Subtract 3 from both sides of the equation. 2x - 3 = 5
2: Add 3 to both sides of the equation to obtain 2x = 8
3: Divide both sides by 2. x = 4. Round the answer to two decimal places.
Thus, the solution to the equation is x = 4.00.
Note that when rounding off a number to two decimal places, the third decimal digit is observed. If the digit is 5 or more, the second decimal place is increased by 1. If it is less than 5, the second decimal place remains the same.The solution to the equation is x = 4.00. This means that if we substitute x = 4.00 into the original equation, the equation is balanced. We obtain:
2(4) - 3 = 5.
This can be simplified to
8 - 3 = 5. Since
the equation is balanced, our solution of x = 4.00 is correct.
For more question equation
https://brainly.com/question/18831322
#SPJ8
If 50.5 {~mol} of an ideal gas is at 6.47 x 10^{5} {~Pa} and 31 {IK} , what is the volume V of the gas?
If 50.5 mol of an ideal gas is at 31 K then the volume (V) of the gas is around 0.641 .
Number of moles (n) = 50.5 mol
Pressure (P) = [tex]6.47 x 10^{5}[/tex]
Temperature (T) = 31 K
To find the volume (V) of the gas, we can use the ideal gas law equation, which relates the pressure (P), volume (V), number of moles (n), and temperature (T) of an ideal gas:
PV = nRT
where R is the ideal gas constant.
It is required to determine the value of the ideal gas constant, R. The ideal gas constant is typically represented by the symbol R and has a value of 8.314 J/(mol·K)
Rearranging the ideal gas law equation to solve for the volume (V):
V = (nRT) / P
Substituting the given values:
[tex]V = (50.5 mol) x (8.314 J/(mol·K)) x (31 K)[/tex]
V = 0.641
Read more about ideal gas equation on:
brainly.com/question/27870704
#SPJ4
Define a ring homomorphism from Z[x] to Z[x]/I for each of the following ideal I: a. I = xZ[x] b. I = (x + 1)Z[x]
a. The ring homomorphism from Z[x] to Z[x]/(x) maps a polynomial f(x) to its residue class modulo x.
b. The ring homomorphism from Z[x] to Z[x]/(x + 1) maps a polynomial f(x) to its residue class modulo (x + 1).
a. To define a ring homomorphism from Z[x] to Z[x]/I, where I = xZ[x], we can define the map as follows:
Let phi: Z[x] -> Z[x]/I be the ring homomorphism.
For any polynomial f(x) = a_nx^n + a_{n-1}x^{n-1} + ... + a_1x + a_0 in Z[x], we map it to its residue class in Z[x]/I.
phi(f(x)) = f(x) + I
So, phi(f(x)) is the residue class of f(x) modulo I.
b. To define a ring homomorphism from Z[x] to Z[x]/I, where I = (x + 1)Z[x], we can define the map as follows:
Let phi: Z[x] -> Z[x]/I be the ring homomorphism.
For any polynomial f(x) = a_nx^n + a_{n-1}x^{n-1} + ... + a_1x + a_0 in Z[x], we map it to its residue class in Z[x]/I.
phi(f(x)) = f(x) + I
So, phi(f(x)) is the residue class of f(x) modulo I, where the coefficients of f(x) are taken modulo (x + 1).
Learn more about ring homomorphism
brainly.com/question/19865639
#SPJ11
Use Matlab (write an M-file) to solve the following sets of simultaneous equations if possible (do the necessary check. The program should display an error if there is no solution). −4x3 + 12x4 = 5 -4x1 - 20x3 + 3x4 = -1
2x1 + 2x3 + 5x4 = 20 X1 - 3x2 + 11x3 — 10x4 = −6
To solve the given system of simultaneous equations using MATLAB, you can use the built-in function linsolve. Here's an example of an M-file that solves the system and performs a check for the existence of a solution:
% Coefficient matrix
A = [-4, 0, 12, 0;
-4, 0, -20, 3;
-12, 2, 0, 5;
1, -3, 11, -10];
% Right-hand side vector
b = [5; -12; 20; -6];
% Solve the system of equations
x = linsolve(A, b);
% Check for existence of solution
if isempty(x)
error('No solution exists for the given system of equations.');
else
disp('Solution:');
disp(x);
end
Save the above code in an M-file, for example, solve_system.m, and then run the script. It will display the solution if one exists, and if not, it will show an error message indicating that no solution exists for the given system of equations.
Make sure to have the MATLAB Symbolic Math Toolbox installed to use the linsolve function.
To learn more about Coefficient : brainly.com/question/1594145
#SPJ11
1. What is the brown gas (name and formula) that nitric acid reacting with copper produces? 2. How can you tell that the gas produced in #1 makes an acid in water? 3. How many moles of the gas in #1 are produced from 1 mole of copper? 4. What color is a copper(II) nitrate when it is diluted in water?
According to the equation, 2 moles of nitrogen dioxide (NO2) are created for every 3 moles of copper (Cu). When copper(II) nitrate is diluted in water, a blue solution results. The amount of nitrogen dioxide produced by 1 mole of copper is (2/3) moles.
Nitrogen dioxide (NO2) is the brown gas created when nitric acid combines with copper.
Nitrogen dioxide (NO2), the gas created in step one, combines with water to dissolve and create nitric acid (HNO3), which creates an acid in water. Following is the response:
NO2 + H2O HNO3
We must apply the balanced chemical equation to calculate the number of moles of gas that are created from 1 mole of copper.
The reaction between copper and nitric acid can be represented as follows:
3Cu + 8HNO3 ⟶ 3Cu(NO3)2 + 2NO + 4H2O
From the equation, we can see that for every 3 moles of copper (Cu), 2 moles of nitrogen dioxide (NO2) are produced.
Copper(II) nitrate, when diluted in water, forms a blue solution.
Learn more about nitrogen dioxide from the given link!
https://brainly.com/question/30459594
#SPJ11
When a 1 g of protein dissolved in water to make 100 mL solution, its osmotic pressure at 5°C was 3.61 torr. What is the molar mass of the protein? R = 0.0821 atm-L/mol-K 69.0 x 104 g/mol 48.1 x 104 g/mol O69.0 x 103 g/mol O 48.1 x 10³ g/mol
The molar mass of the protein is 69.0 x 103 g/mol.
To calculate the molar mass of the protein, we can use the formula:
Molar mass = (osmotic pressure * volume) / (R * temperature)
In this case, the osmotic pressure is given as 3.61 torr, the volume is 100 mL (or 0.1 L), the gas constant (R) is 0.0821 atm-L/mol-K, and the temperature is 5°C (or 278 K).
Plugging in these values into the formula, we get:
Molar mass = (3.61 torr * 0.1 L) / (0.0821 atm-L/mol-K * 278 K)
Simplifying this expression, we find:
Molar mass = 0.361 torr-L / (0.0821 atm-L/mol-K * 278 K)
Converting torr to atm and simplifying further, we have:
Molar mass = 0.361 atm-L / (0.0821 atm-L/mol-K * 278 K)
Canceling out the units, we get:
Molar mass = 0.361 / (0.0821 * 278)
Calculating this expression, we find:
Molar mass ≈ 69.0 x 103 g/mol
Therefore, the molar mass of the protein is approximately 69.0 x 103 g/mol.
Know more about molar mass here:
https://brainly.com/question/31545539
#SPJ11
Yeast is added to a vat of grape juice in order to ferment it to make wine. The amount of yeast present in the vat doubles every 4 hours after it is added. Suppose that 5 grams of yeast is added to the vat at t = 0. A formula for the amount of yeast at time t is A(t) = 5. (2) ¹/4 (a) How much yeast will be present in 24 hour? (b) How much time will elapse before the amount of yeast reaches 500 grams?
(a) After 24 hours, there will be 320 grams of yeast present in the vat.
(b) It will take approximately 26.5756 hours for the amount of yeast to reach 500 grams.
How to Calculate the amount of Yeast?(a) To find the amount of yeast present in 24 hours, we can use the formula A(t) = 5 * [tex](2)^{(t/4)}.[/tex]
Plugging in t = 24, we get:
A(24) = 5 * [tex](2)^{(24/4)}[/tex] = 5 *[tex](2)^6[/tex] = 5 * 64 = 320 grams.
(b) To determine the time it takes for the amount of yeast to reach 500 grams, we can rearrange the formula A(t) = 5 * [tex](2)^{(t/4)[/tex] and solve for t:
500 = 5 * [tex](2)^{(t/4)[/tex]
Dividing both sides by 5:
100 = [tex](2)^{(t/4)[/tex]
Taking the logarithm base 2 of both sides to isolate the exponent:
log₂(100) = t/4
Using logarithmic properties, we find:
t/4 = log₂(100)
t = 4 * log₂(100)
Using a calculator, we can evaluate the right-hand side:
t ≈ 4 * 6.6439 ≈ 26.5756
Learn more about yeast on:
https://brainly.com/question/18014973
#SPJ4
We are living in a world dominated by petrochemical products. Despite the immense convenience offered by petrochemical products (e.g. plastic bags, gasoline, etc.), they are always believed to be the primary reason for global warming. Renewable energy and more sustainable materials may be the answer. However, their development remains very challenging in most countries. Discuss any three (3) factors that hinder them from progressing. Please provide solid justification to support your argument.
Three factors that hinder the progress of renewable energy and sustainable materials are: Limited Infrastructure and Investment, Political and Regulatory Barriers, Technological Limitations and Scalability.
1. Limited Infrastructure and Investment: The transition to renewable energy requires significant infrastructure development, such as solar and wind farms, and a robust grid system for efficient distribution. However, the initial investment costs for setting up such infrastructure are often high, and the return on investment may take time. Many countries face financial constraints and prioritize immediate needs over long-term sustainability, making it challenging to allocate sufficient funds for renewable energy projects.
2. Political and Regulatory Barriers: The political landscape plays a crucial role in shaping energy policies and regulations. In some cases, there is a lack of political will to prioritize renewable energy over traditional fossil fuels. Political interests, lobbying, and the influence of the fossil fuel industry can hinder the adoption of renewable energy sources. Additionally, regulatory frameworks may not provide adequate support or incentives for renewable energy development, making it difficult for new technologies to thrive.
3. Technological Limitations and Scalability: Renewable energy technologies are still evolving and face challenges related to efficiency, storage, and scalability. While advancements have been made, there is a need for further research and development to improve the performance and cost-effectiveness of renewable energy systems. Additionally, integrating renewable energy into existing infrastructure and addressing the intermittency of certain sources like solar and wind pose technical challenges that require innovative solutions.
To overcome these hindrances, governments and organizations need to prioritize long-term sustainability, provide financial incentives and support for renewable energy projects, revise regulatory frameworks to favor clean energy, invest in research and development, and promote public awareness about the benefits of renewable energy for mitigating climate change.
Learn more about renewable energy
https://brainly.com/question/17373437
#SPJ11
i. What are the properties of Na2C2O4 that make it suitable to standardize permanganate?ii. Explain the following. Why is it necessary to heat the oxalate-permanganate reaction initially, but not once the reaction has begun
Sodium oxalate has the properties of colorless solid to make it a suitable primary standard for the standardization of KMnO4 solution. In ii) the initial heating is necessary to provide energy to initiate the reaction.
i. Properties of Na2C2O4 that make it suitable to standardize permanganateNa2C2O4 (sodium oxalate) is a colorless solid. It is soluble in water, and it has a relatively high molar mass.
Sodium oxalate is suitable for standardizing potassium permanganate (KMnO4) solution because it is a primary standard and is available in pure form. A primary standard is a substance that is used to make a standard solution that can be utilized to analyze a solution of unknown concentration. It is essential that a primary standard is pure, stable, water-soluble, have a high molar mass, and its solution can be made with high accuracy.
Therefore, sodium oxalate has the properties required to make it a suitable primary standard for the standardization of KMnO4 solution.
ii. The reaction between potassium permanganate (KMnO4) and sodium oxalate (Na2C2O4) is used to standardize the KMnO4 solution. The reaction is an oxidation-reduction reaction, and it is an acid-base reaction. The balanced chemical equation for the reaction is:5C2O42− + 2MnO4− + 16H+ → 2Mn2+ + 10CO2 + 8H2O.
Initially, heating the reaction mixture is necessary to initiate the reaction. The reaction is endothermic, so it requires energy to start. Once the reaction has begun, it generates heat, so no additional heating is necessary. The production of CO2 gas bubbles indicates that the reaction has begun.
Therefore, the initial heating is necessary to provide energy to initiate the reaction. After the reaction has begun, no additional heating is necessary because the reaction produces heat, and it is self-sustaining.
To know more about Primary standard visit-
brainly.com/question/29749783
#SPJ11
Question 2 A project has a useful life of 10 years, and no salvage value. The firm uses an interest rate of 12 % to evaluate engineering projects. A project has uncertain first costs and annual
The project has a useful life of 10 years and no salvage value. To evaluate engineering projects, the firm uses an interest rate of 12%. Since the first costs and annual costs of the project are uncertain, it is important to calculate the Net Present Value (NPV) to determine the project's profitability.
To calculate the NPV, we need to discount the future cash flows of the project to their present value. The formula for calculating NPV is:
[tex]NPV = Cash Flow / (1 + r)^t[/tex]
where r is the interest rate and t is the time period. In this case, we need to calculate the NPV for each year of the project's useful life. Since there is no salvage value, the cash flow will be the negative of the annual cost of the project.
Let's say the annual cost is $10,000. We can calculate the NPV for each year using the formula mentioned above. The NPV for year 1 would be:
NPV1 = -$10,000 / (1 + 0.12)^1 = -$8,928.57 (negative because it represents an outgoing cash flow)
Similarly, we can calculate the NPV for each year of the project's useful life. To determine the total NPV, we sum up the NPVs for each year.
By calculating the NPV, we can assess whether the project is financially viable or not. A positive NPV indicates that the project is profitable, while a negative NPV suggests that the project may not be financially feasible.
In summary, to evaluate the profitability of the project with uncertain costs, we need to calculate the NPV by discounting the future cash flows to their present value using the interest rate.
Know more about Net Present Value (NPV)
https://brainly.com/question/32743126
#SPJ11
14-
thermodynamics عرصات
A Carnot heat engine is working between two thermal reservoirs of 628.2 C and 211.1 C, what is the Carnot thermal efficiency (96)? OA 86.16 OB. 66.40 C 0.46 D. 46.28 E. 0.66
Carnot thermal efficiency is given by ηcarnot = (T1 - T2)/ T1Where, ηcarnot = Carnot thermal efficiencyT1 = Temperature of the source in KelvinT2 = Temperature of the sink in Kelvin.
Given that, The temperatures of the source and the sink are given asT1 = 628.2 C = 901.35 KT2 = 211.1 C = 484.25 K.
Now, Substituting the given values in the above formula,
ηcarnot = (T1 - T2)/ T1= (901.35 - 484.25) / 901.35= 46.27%.
Therefore, the Carnot thermal efficiency is 46.27%.
We are given the temperatures of the source and the sink, to calculate the Carnot thermal efficiency. The Carnot thermal efficiency is the maximum possible efficiency of a heat engine. It is based on the concept of reversible engines, where the engine can perform work without any loss of energy. The Carnot cycle is a hypothetical cycle that serves as the upper limit of a heat engine's efficiency.
It consists of four stages, two adiabatic processes, and two isothermal processes. The Carnot cycle is a reversible cycle that can be executed in both directions.
The Carnot cycle efficiency is given by ηcarnot = (T1 - T2)/ T1. Here, T1 and T2 are the temperatures of the source and the sink in Kelvin, respectively.
Using this formula, we can calculate the Carnot thermal efficiency.
Substituting the given values, we get ηcarnot = (901.35 - 484.25) / 901.35 = 46.27%.
The Carnot thermal efficiency of a heat engine working between two thermal reservoirs of 628.2 C and 211.1 C is 46.27%.
To know more about Carnot cycle :
brainly.com/question/31586892
#SPJ11
1.3) Which of the following alkyl halides cannot be used to
synthesize an ester from a carboxylate anion? -CH3Br -CH2CH3Cl
-(CHE)3Cl -CH3CH2CH2Br
The alkyl halide that cannot be used to prepare (CHE)3Cl is CH3CH2CH2Br.
This alkyl halide cannot be used to prepare (CHE)3Cl because (CHE)3Cl is a tertiary alkyl halide, which means it has a carbon atom bonded to three other carbon atoms. CH3CH2CH2Br is a primary alkyl halide, meaning it has a carbon atom bonded to only one other carbon atom. In order to convert a primary alkyl halide into a tertiary alkyl halide, multiple substitution reactions would be required, which are generally difficult to carry out.
On the other hand, (CHE)3Cl can be prepared from CH3Cl by reacting it with excess CH3MgBr (Grignard reagent) followed by treatment with HCl. This reaction allows for the direct substitution of the halogen atom on the methyl group, resulting in the formation of (CHE)3Cl.
In summary, CH3CH2CH2Br cannot be used to prepare (CHE)3Cl because it is a primary alkyl halide, while (CHE)3Cl is a tertiary alkyl halide. The conversion from a primary alkyl halide to a tertiary alkyl halide requires multiple substitution reactions, which are generally difficult to carry out.
Know more about alkyl halide here:
https://brainly.com/question/29371143
#SPJ11
California and New York lead the list of average teachers’ salaries. The California yearly average is $64,421 while teachers in New York make an average annual salary of $62,332. Random samples of 45 teachers from each state yielded the following.
California New York
Sample Mean 64,510 62,900
Population Standard Deviation 8,200 7,800
At a = 0. 10, is there a difference in means of the salaries?
Note: I would like someone to please explain the process to find the answer step by step and also show me how to find this answer on Excel. I know how to find the answer for problems that contain data sets, but do not know how when there are not any datum
Yes, there is a significant difference in means between the salaries of teachers in California and New York at α = 0.10
How to determine the valueTo determine the value, we have that;
Using a two-sample t-test to test this hypothesis, let us calculate the test statistic using the formula:
t = (x₁ - x₂) / sqrt((s₁²/n₁) + (s₂²/n₂))
Substitute the value, we have;
t = (64,510 - 62,900) / √((8,200²/45) + (7,800²/45))
Find the square root of the values and multiply, we have
t = (64,510 - 62,900) / 533.45
t = 1.51
Then, we have that;
Degrees of freedom= (n₁ + n₂ - 2) = (45 + 45 - 2) = 88.
The significance level, α = 0.1
The critical value = 1.290
The calculated t-statistic is greater than the critical value and thus we can say that there is a significant difference in means between the salaries of teachers in California and New York
Learn more about critical value at: https://brainly.com/question/14040224
#SPJ1
Simulate the car following behaviour for the following situation using a system update time of 0.5 {sec} . Two vehicles are moving at an initial speed of 17 {~m} / {s}
The specific details of the car-following model, such as acceleration and deceleration behavior, can vary depending on the chosen model. Additionally, you may need to consider factors like traffic conditions, driver behavior, and road characteristics to create a more accurate simulation.
To simulate their behavior, we can follow these steps:
1. Initialize the positions and velocities of both vehicles.
- Vehicle 1: Position = 0, Velocity = 17 m/s
- Vehicle 2: Position = 0, Velocity = 17 m/s
2. Calculate the distance between the two vehicles using the equation:
Distance = Position of Vehicle 2 - Position of Vehicle 1
3. Determine the desired following distance between the vehicles. Let's say it is 10 meters.
4. Calculate the relative velocity between the vehicles using the equation:
Relative Velocity = Velocity of Vehicle 2 - Velocity of Vehicle 1
5. Apply the car-following model to update the velocities of both vehicles. This model can be based on the relative velocity and distance between the vehicles. One commonly used model is the "Intelligent Driver Model (IDM)".
6. Update the positions of both vehicles based on their velocities and the system update time (0.5 seconds).
7. Repeat steps 2 to 6 until the desired simulation time is reached.
By following these steps, you can simulate the car following behavior for the given situation using a system update time of 0.5 seconds and initial speeds of 17 m/s for both vehicles.
Learn more about acceleration from the link given below:
https://brainly.com/question/460763
#SPJ11
A specific strong steel alloy has a elastic limit of 1460 Mpa and a fracture toughness Kic of 98 MPavm. Calculate the size of the surface tear above which it would cause catastrophic failure at a stress of 50% of the elastic limit. (Take Y = 1, for standard cases) 5. ac 5.74 mm
The required surface tear size above which it would cause catastrophic failure at a stress of 50% of the elastic limit is 5.74 mm.
Given elastic limit of the specific strong steel alloy (σe) = 1460 Mpa
Fracture toughness (Kic) = 98 MP avm
Stress at which catastrophic failure occur = 50% of the elastic limit
Surface tear size (ac) to cause catastrophic failure is to be calculated
Therefore, using the given values in the formulae, we get;
KIC = Y σ √πacKIC² / Y² σ²πac
= 0.25* KIC² / Y² σ²πac
= 0.25 x (98)^2 / (1)^2 x (1460)^2πac
= 5.74 mm (approx)
Therefore, the required surface tear size above which it would cause catastrophic failure at a stress of 50% of the elastic limit is 5.74 mm.
To know more about catastrophic failure visit:
https://brainly.com/question/31989796
#SPJ11
Excavated soil material from a building site contains cadmium.
When the soil was analysed for the cadmium, it was determined that
its concentration in the soil mass was 250 mg/kg. A TCLP test was
then
The concentration of cadmium in the excavated soil was 250 mg/kg, while the leachate from the TCLP test contained 5 mg/L of cadmium.
conducted to determine the leachability of cadmium from the soil. The results of the TCLP test showed that the concentration of cadmium in the leachate was 5 mg/L.
The Toxicity Characteristic Leaching Procedure (TCLP) test is a standardized laboratory test used to assess the potential leaching of hazardous substances from solid waste materials. In the case of cadmium, the TCLP test measures the leachability of cadmium from the soil, simulating its potential movement into groundwater or surface water.
In this scenario, the concentration of cadmium in the excavated soil material was found to be 250 mg/kg. This value represents the total amount of cadmium present in the soil mass. However, the total concentration of cadmium alone does not indicate its potential impact on the environment or human health.
To evaluate the potential risk posed by the cadmium in the soil, the TCLP test was conducted. The test measures the leachability of cadmium by subjecting the soil to an acidic solution that simulates the conditions of a landfill or disposal site. The resulting leachate is then analyzed to determine the concentration of cadmium that has leached from the soil.
In this case, the TCLP test showed that the concentration of cadmium in the leachate was 5 mg/L. This value indicates the amount of cadmium that was mobilized and could potentially leach into the surrounding environment under the simulated conditions of the test. A concentration of 5 mg/L suggests that the leachability of cadmium from the soil is relatively low.
To assess the environmental and human health risks associated with the excavated soil, further evaluation would be needed. Regulatory standards and guidelines typically exist for permissible concentrations of cadmium in soil and water. Comparing the results of the TCLP test to these standards would help determine if any remediation or management measures are necessary to mitigate potential risks.
Learn more about Cadmium
brainly.com/question/13560839
#SPJ11
Q1) 73% of 625 is what number?
73 percent of 625 is approximately 456.
Q1) Calculating the 73% of 625 will give us the number we are looking for.
To find out, we can use the following formula:
% / 100 × Whole Number = Answer
Where: % represents the percentage we want to find. Whole Number represents the whole amount that the percentage is taken from.
Answer represents the result of the percentage calculation.
Therefore, to find out what number is 73% of 625, we can plug in the given values into the formula as follows:
73 / 100 × 625 = Answer
Simplifying this expression gives us:0.73 × 625 = Answer
Multiplying 0.73 and 625 gives us: 455.625 = Answer
Therefore, 73% of 625 is approximately 456.
To sum up, the number we were looking for is approximately 456. This answer was found by using the formula:
% / 100 × Whole Number = Answer.
To know more about percentage, visit:
https://brainly.com/question/32197511
#SPJ11
Let u= (0, 1, 2) and v = (2, 1, -1) be vectors in R3.
Part(a) [3 points] If P(5, 6, 7) is the terminal point of the vector 2u, then what is its initial point? Show your work.Part(b) [4 points] Find ||u||2v - (v. Part(c) [4 points] Find vectors x and y in R3 such that u = x + y where x is parallel to v and y is orthogonal to V. Hint: Consider orthogonal projection
a). The initial point of the vector 2u is (5, 4, 3).
b). ||u||²v - (v) = (8, 4, -4).
c). x = (-1/3, -1/6, 1/6) and y = (1/3, 7/6, 11/6) satisfy the conditions u = x + y,
Part (a):
To find the initial point of the vector 2u, we need to subtract 2u from the terminal point P(5, 6, 7).
Initial point = P - 2u
P(5, 6, 7) - 2u = (5, 6, 7) - 2(0, 1, 2)
= (5, 6, 7) - (0, 2, 4)
= (5 - 0, 6 - 2, 7 - 4)
= (5, 4, 3)
Therefore, the initial point of the vector 2u is (5, 4, 3).
Part (b):
To find ||u||²v - (v), we first need to compute ||u||^2 and then multiply it by v, and finally subtract v from the result.
||u||² = (0)² + (1)² + (2)²
= 0 + 1 + 4
= 5
||u||²v = 5(2, 1, -1)
= (10, 5, -5)
||u||²v - (v) = (10, 5, -5) - (2, 1, -1)
= (10 - 2, 5 - 1, -5 + 1)
= (8, 4, -4)
Therefore, ||u||²v - (v) = (8, 4, -4).
Part (c):
To find vectors x and y such that u = x + y, where x is parallel to v and y is orthogonal to v, we can use the concept of orthogonal projection.
The vector x parallel to v can be obtained by projecting u onto the direction of v. The projection of u onto v is given by:
proj_v(u) = (u · v) / ||v||² * v
where · denotes the dot product.
Let's calculate the projection of u onto v:
(u · v) = (0)(2) + (1)(1) + (2)(-1)
= 0 + 1 - 2
= -1
||v||² = (2)² + (1)² + (-1)²
= 4 + 1 + 1
= 6
proj_v(u) = (-1) / 6 * (2, 1, -1)
= (-1/6)(2, 1, -1)
= (-1/3, -1/6, 1/6)
So, x = proj_v(u) = (-1/3, -1/6, 1/6).
Now, to find y, which is orthogonal to v, we can subtract x from u:
y = u - x
= (0, 1, 2) - (-1/3, -1/6, 1/6)
= (0 + 1/3, 1 + 1/6, 2 - 1/6)
= (1/3, 7/6, 11/6)
Therefore, x = (-1/3, -1/6, 1/6) and y = (1/3, 7/6, 11/6) satisfy the conditions u = x + y,
where x is parallel to v and y is orthogonal to v.
To know more about vector click-
https://brainly.com/question/12949818
#SPJ11
The initial point of the vector 2u is (5, 4, 3). A vector orthogonal to v is (0, -1, -1). The orthogonal projection of u onto v is (12, 9, 0).
(a) The initial point of the vector 2u can be found by subtracting 2u from the terminal point P(5, 6, 7). Since u = (0, 1, 2), we have 2u = 2(0, 1, 2) = (0, 2, 4). Therefore, the initial point is obtained by subtracting (0, 2, 4) from P(5, 6, 7), giving us:
Initial point = P - 2u = (5, 6, 7) - (0, 2, 4) = (5, 6, 7) - (0, 2, 4) = (5, 4, 3).
(b) To find a vector orthogonal to v, we can take the cross product of v with any other vector. Let's choose the standard unit vector i = (1, 0, 0). Taking the cross product, we have:
v x i = (2, 1, -1) x (1, 0, 0) = (0(-1) - 0(1), -(2(0) - 1(1)), 2(0) - 1(1)) = (0, -1, -1).
Therefore, (0, -1, -1) is a vector orthogonal to v.
(c) The expression ||u||²v - (v · u)u represents the orthogonal projection of u onto the vector v. Let's compute it:
||u||²v = (0² + 1² + 2²)(2, 1, -1) = (1 + 1 + 4)(2, 1, -1) = (6)(2, 1, -1) = (12, 6, -6).
(v · u)u = (2, 1, -1) · (0, 1, 2)(0, 1, 2) = (0(2) + 1(1) + 2(-1))(0, 1, 2) = (0 - 1 - 2)(0, 1, 2) = (-3)(0, 1, 2) = (0, -3, -6).
Therefore, ||u||²v - (v · u)u = (12, 6, -6) - (0, -3, -6) = (12, 6, -6) + (0, 3, 6) = (12, 9, 0).
To learn more about vector refer:
https://brainly.com/question/15519257
#SPJ11
From the sample space S={1,2,3,4,…,15} a single number is to be selected at random. Given the following events, find the indicated prohability A. The selected number is even. B. The selected number is a multiple of 4 . C. The sclected number is a prime number: P(C) P(C)= (Simplify your answer. Type an integet of a fraction.)
A. Probability that the selected number is even: 7/15
B. Probability that the selected number is a multiple of 4: 3/15
C. Probability that the selected number is a prime number: 6/15
A. To find the probability that the selected number is even, we need to determine the number of even numbers in the sample space S.
In this case, there are 7 even numbers (2, 4, 6, 8, 10, 12, 14) out of a total of 15 numbers.
Therefore, the probability P(A) is given by:
P(A) = Number of favorable outcomes / Total number of outcomes
P(A) = 7 / 15
B. To find the probability that the selected number is a multiple of 4, we need to determine the number of multiples of 4 in the sample space S.
In this case, there are 3 multiples of 4 (4, 8, 12) out of a total of 15 numbers.
Therefore, the probability P(B) is given by:
P(B) = Number of favorable outcomes / Total number of outcomes
P(B) = 3 / 15
C. To find the probability that the selected number is a prime number, we need to determine the number of prime numbers in the sample space S.
In this case, there are 6 prime numbers (2, 3, 5, 7, 11, 13) out of a total of 15 numbers.
Therefore, the probability P(C) is given by:
P(C) = Number of favorable outcomes / Total number of outcomes
P(C) = 6 / 15
Learn more about the probability visit:
https://brainly.com/question/13604758
#SPJ4
At a point in a 15 cm diameter pipe, 2.5 m above its discharge end, the pressure is 250kPa. If the flow is 35 liters/second of oil (SG-0.762), find the head loss between the point and the discharge end. 27.98 m 22.98 m 35.94 m 30.94 m
The head loss between the point and the discharge end equation is option d) 0.7323 m.
Given data: Diameter of the pipe = 15 cm
Radius of the pipe = 7.5 cm
Height of the point above the discharge end = 2.5 m
Pressure at the point = 250 kPa
Flow of oil = 35 L/s
Specific gravity of oil = 0.762
Formula used: Bernoulli’s Equation
Bernoulli’s Equation:
P₁/ρ + v₁²/2g + z₁ = P₂/ρ + v₂²/2g + z₂
where P₁/ρ + v₁²/2g + z₁ = Pressure head at point
1P₂/ρ + v₂²/2g + z₂ = Pressure head at point 2
where P = Pressure
ρ = Density of the fluid
v = Velocity of the fluid
g = Acceleration due to gravity
z = Elevation
Let the head loss between the point and the discharge end be ‘h’.
Discharge end of the pipe:
Pressure head at the discharge end of the pipe = 0 m
Velocity at the discharge end of the pipe = v₁
Let us consider the point to be point 2.
Point 2: Pressure head at point 2 = 250 kPa / (1000 kg/m³ * 9.81 m/s²) = 0.02542 m
Velocity at point 2 = Q / A₂
= (35 × 10⁻³ m³/s) / π (0.15 m)² / 4
= 0.756 m/s
Density of the fluid = Specific gravity × Density of water
= 0.762 × 1000 kg/m³
= 762 kg/m³
Let us calculate the cross-sectional area at point 2.
A₂ = π (d/2)²/4
= π (0.15 m)²/4
= 0.01767 m²
The velocity at the discharge end of the pipe is zero. Hence, v₁ = 0.0 m/s.
Now, we need to find the head loss between the point and the discharge end.
v₁²/2g = (250 × 10³ N/m²) / (762 kg/m³ * 9.81 m/s²) + (0.756²/2g) + 2.5 m - 0v₁²/2g
= 0.7323 m
head loss, h = v₁²/2g = 0.7323 m
Hence, the correct option is (d) 30.94 m.
To know more about the equation, visit:
https://brainly.com/question/649785
#SPJ11
VB at B. For the cantilever steel beam [E = 230 GPa; / = 129 × 106 mm4], use the double-integration method to determine the deflection Assume L = 3.7 m, Mo = 61 kN-m, and w = = 13 kN/m. W Mo Answer:
The deflection of the cantilever steel beam is approximately (x²) / 102,564,102,564,102.56.
To determine the deflection of the cantilever steel beam using the double-integration method, we can follow these steps:
First, let's calculate the reaction force at the fixed end of the beam. We can use the equation for the sum of moments about the fixed end:
ΣM = 0
(-Mo) + (VB x L) = 0
VB x L = Mo
VB = Mo / L
VB = 61 kN-m / 3.7 m
VB ≈ 16.49 kN
Next, let's find the equation for the deflection of the beam. The equation for the deflection of a cantilever beam under a uniformly distributed load (w) is given by:
δ = (w x x²) / (6 x E x I)
where δ is the deflection, w is the load per unit length, x is the distance from the fixed end, E is the modulus of elasticity, and I is the moment of inertia.
Now, we need to calculate the moment of inertia (I) of the beam. The moment of inertia for a rectangular cross-section can be calculated using the formula:
I = (b x h³) / 12
where b is the width of the beam and h is the height of the beam.
Given that the beam is rectangular and the dimensions are not provided in the question, we cannot determine the exact moment of inertia without additional information.
However, if we assume a typical rectangular cross-section with a width of 100 mm and a height of 200 mm, we can calculate the moment of inertia as follows:
I = (100 mm x (200 mm)³) / 12
I ≈ 133,333,333.33 mm⁴
Now we can substitute the values into the deflection equation and solve for the deflection (δ). Using the given values:
δ = (13 kN/m x x²) / (6 x 230 GPa x 133,333,333.33 mm⁴)
Simplifying the units:
δ = (13 x 10^3 N/m x x²) / (6 x 230 x 10⁹ N/mm² x 133,333,333.33 mm⁴)
δ = (13 x 10³ x x²) / (6 x 230 x 10⁹ x 133,333,333.33)
δ ≈ (x²) / 102,564,102,564,102.56
To learn more about cantilever steel beam:
https://brainly.com/question/16791806
#SPJ11
Find the solution to the initial value problem (1+x^11)y′+11x^10y=9x^17 subject to the condition y(0)=2.
The initial condition y(0) = 2, we get:2 = 0 + C So, the solution to the initial value problem is:y = -([tex]9/11) x^11 ln|x| + 2(1+x^11).[/tex]
Given differential equation [tex](1+x^11)y′+11x^10y=9x^17[/tex]with initial condition y(0) = 2
To solve the initial value problem, we need to find y' first. For that, divide the differential equation by (1+x^11):y' + 11x^10/(1+x^11)y = 9x^17/(1+x^11)This is a first-order linear differential equation of the form:
y' + P(x)y = Q(x)where P(x) = 11x^10/(1+x^11) and Q(x) = 9x^17/(1+x^11)Using the integrating factor, I = e^ integral P(x) dx, we can solve this equation. I = e^ integral P(x) dx = e^ integral (11x^10/(1+x^11)) dx Taking u = 1+x^11, the integral becomes: integral [tex]11x^10/(1+x^11) dx= 11/11 integral (u-1)/u du= ln|u| - ln|u-1| + C = ln|(1+x^11)/(x^11)| + C.[/tex]
Now, the integrating factor is I = e^ln|(1+x^11)/(x^11)| = (1+x^11)/x^11Multiplying both sides of the differential equation by I, we get:[tex](1+x^11)y'/x^11 + 11(x^11+y^11)/(x^11(1+x^11))y = 9/(1+x^11).[/tex]
Now, the left-hand side of the equation can be written in the form of the derivative of a product using the product rule. Differentiate both sides of the equation and simplify to get:
[tex]y/(1+x^11) = -9/11 ln|x| + C[/tex] (where C is the constant of integration)
Multiplying both sides of the equation by (1+x^11), we get:y = -(9/11) x^11 ln|x| + C(1+x^11).
Substituting t
To know more about differential visit:
https://brainly.com/question/33433874
#SPJ11
(b) How does reinforced concrete and prestressed concrete overcome the weakness of concrete in tension? You have been assigned by your superior to design a 15 m simply supported bridge beam and he gives you the freedom to choose between reinforced concrete and prestressed concrete. Please make your choice and give justification of your choice.
The technique produces concrete with high tensile strength and is used to build structures with large spans, such as bridges, long beams, and cantilevers.
Reinforced concrete and prestressed concrete are two popular techniques that help overcome the weakness of concrete in tension. Reinforced concrete and prestressed concrete are used to build structures that are both durable and reliable.
Reinforced concrete is made by mixing Portland cement, water, and aggregate. It has excellent compressive strength but weak tensile strength. The tensile strength of reinforced concrete is improved by embedding steel reinforcement rods or bars in it during casting.
The concrete is pre-stressed by tensioning the steel reinforcement rods or tendons before casting. Post-tensioning involves tensioning the tendons after the concrete has hardened.
To know more about Reinforced concrete visit:
https://brainly.com/question/32759577
#SPJ11
If the absolute pressure is 237.0kpa and the atmospheric
pressure is 96.0kpa. the the gage pressure. Provide your answer in
three decimal places.
please answer immediately
The gage pressure is 141 kPa when the absolute pressure is 237.0 kPa and the atmospheric pressure is 96.0 kPa.
The gage pressure when the absolute pressure is 237.0 kPa and the atmospheric pressure is 96.0 kPa can be determined by subtracting the atmospheric pressure from the absolute pressure.
Gage pressure is defined as the difference between absolute pressure and atmospheric pressure. It is the pressure measured by a pressure gauge.
In the given situation, gage pressure can be determined as follows:
Gage pressure = Absolute pressure - Atmospheric pressure
Gage pressure = 237.0 kPa - 96.0 kPa
Gage pressure = 141 kPa
Therefore, the gage pressure is 141 kPa.
In conclusion, the gage pressure is 141 kPa when the absolute pressure is 237.0 kPa and the atmospheric pressure is 96.0 kPa.
To know more about gage pressure visit:
brainly.com/question/13390708
#SPJ11
Question 5 2 pts Activity No. 0330 is Concrete Placing for Foundation in the Temple Underground Parking Project, with an estimated cost of $73,400 for 1.200 c.y. of concrete. After two weeks, $35.540 was already spent on this activity for 690 c.y. Currently, an estimated cost of $46,660 for 850 c.y. is needed to complete this activity on the project. What is the Estimated Total Cost at Completion (ETC)? Enter the number only, without the dollar sign or comma.
the Estimated Total Cost at Completion (ETC) is $46,660.
Given, Activity No. 0330 is Concrete Placing for Foundation in the Temple Underground Parking Project
Estimated cost of $73,400 for 1.200 c.y. of concrete.
$35.540 was already spent on this activity for 690 c.y.
Currently, an estimated cost of $46,660 for 850 c.y. is needed to complete this activity on the project.
We need to find the Estimated Total Cost at Completion (ETC)
So, the formula for ETC is as follows:
ETC = Actual cost to date + Estimated cost of the work remaining
The actual cost for 690 c.y. is $35,540.
So the estimated cost for 510 c.y. is estimated to be:
Estimated cost for 510 c.y. = 46,660 - 35,540 = 11,120 dollars
And the estimated total cost at completion (ETC) is the sum of actual cost to date and estimated cost of the work remaining:
ETC = 35,540 + 11,120 = 46,660 dollars
Therefore, the Estimated Total Cost at Completion (ETC) is $46,660.
To know more about cost visit:
https://brainly.com/question/33151193
#SPJ11