A small PWR plant operates at a power of 485 MWt. The core, which is approximately 75.4 in. in diameter and 91.9 in. high, consists of a square lattice of 23,142 fuel tubes of thickness 0.021 in. and inner diameter of 0.298 in. on a 0.422-in. pitch. The tubes are filled with 3.40 w/o-enriched The core is cooled by water, which enters at the bottom at and passes through the core at a rate of at 2,015 psia. Compute (a) the average temperature of the water leaving the core; (b) the average power density in kW/liter; (c) the maximum heat production rate, assuming the reactor core is bare.

Based on the calculations, the average temperature of the water leaving this core is equal to 531.11 Btu/lb.

Since the core is cooled by water, which enters at the bottom at 496°F, the heat input ([tex]h_{in}[/tex]) would be equal to 483.02 Btu/lb based on the steam table.

Given the following data:

Substituting the given parameters into the formula, we have;

[tex]h_{out}= \frac{q}{w} + h_{in}\\\\h_{out}= \frac{1.635 \times 10^9}{34 \times 10^6} + 483.02\\\\h_{out}= 48.09 + 483.02\\\\h_{out}= 531.11\;Btu/lb[/tex]

First of all, we would determine the area of this core by using this formula:

Area = πd²/2

Area = 3.142 × (0.298/2)²

Area = 0.0698 in².

Mathematically, the average power density is given by:

[tex]q_{av}=\frac{q}{W} =\frac{q}{\pi A^2H \times 23142} \\\\q_{av}=\frac{485 \times 10^3}{3.142 \times 0.0698^2 \times 91.9 \times 0.01639 \times 23142} \\\\q_{av}=199.5\;kW/liter.[/tex]

In this scenario, we would assume the reactor core is bare. Thus, the heat is given by:

[tex]q(0) = \frac{2.32PE_1}{HE_R} \\\\q(0) =\frac{2.32 \times 485 \times 180}{23142 \times 200} \\\\q(0) =0.044 \;MW = 1.5 \times 10^8 \;Btu/hr^2[/tex]

For the maximum heat production rate, we have:

[tex]q_{max}=\frac{q(0)}{2HA^2} \\\\q_{max}=\frac{1.5 \times 10^8}{2 \times (\frac{75.4}{2} \times \frac{1}{12}) \times (\frac{0.298}{2} \times \frac{1}{12})} \\\\q_{max}=\frac{1.5 \times 10^8}{2 \times 3.1417 \times 0.00124} \\\\q_{max}=\frac{1.5 \times 10^5}{0.007791416}\\\\q_{max}=1.55 \times 10^8 \;Btu/hr.ft^3[/tex]

Read more on maximum heat here: https://brainly.com/question/13577244

Technician A says that the cylinders should be bored and/or honed to match the size of the pistons to be used. Technician B says that bolt holes should be chamfered and cleaned with a thread chaser before assembly. Who is right

Three rolling cylinders are connected with a pure rolling contact with a speed ratio of 3 in cylinder 1 and 2, if the center distance of the cylinder 1&2 and cylinder 2&3 are 16inches & 18 respectively. Calculate the diameter and mm of each cylinder. If the velocity is 20m/s.

Tech A says that a parasitic draw is measured in volts. Tech B says that pulling fuses one at a time can help locate a parasitic draw. Who is correct

An undeformed specimen of some alloy has an average grain diameter of 0.040 mm. You are asked to reduce its average grain diameter to 0.010 mm. Is this possible

6.
How has technology has allowed humans to thrive?

by playing an important role in evolution

by creating tools that make human life easier

by changing the structure of the human body

by inspiring healthy competition among people

Engine coolant is typically made up of what?

OA. 25% Antifreeze/75% water
OB. 50% Antifreeze/50% water
OC. 75% Antifreeze/25% water
OD. 33% Antifreeze/67% water​

Which sentence from the passage uses passive voice?

Question 9 options:

a)

E-books also make reading easier for people with disabilities. (paragraph 12)


b)

M.K. sees it another way. (paragraph 16)


c)

In one year, e-reader production released 2350 million kilograms of carbon dioxide into the atmosphere. (paragraph 8)


d)

The Diamond Sutra was printed in China in 868 AD. (p

Select three jobs that ſvould be undertaken by someone just starting his or her career as an environmental
engineer.
designing a renewable water system in a remote area
designing a bridge that will cross a major river
designing a building that can withstand a massive earthquake
designing a car that emits less carbon emissions than previously designed automobiles
designing a greenhouse to reduce pollution and provide food

3. Briefly explain the conduction mechanism in metals?​

New tie rod ends are being installed. Technician A says it is a good idea to replace the cotter pin. Technician B says to tighten the retaining nut to the low side of the torque spec then further tighten to align the cotter key hole. Which technician is correct

Pleas help. The dimensions of this figure are changed so that the new surface area is exactly 12 what it was originally. What is the new surface area? Enter your answer as a decimal in the box. Answer. Yd²

The basic building block of digital technology is the
Select one:
a. flip-flop
b. binary adder
c. gate
d. truth table

In what way is a parallel circuit different from a series circuit?

A blue and a yellow cubes are rolled- What is the probability that a yellow cube is a multiple of 3 and the product is 6?

Advantage and disadvantages of Bessemer process of steel making

In order for communication to be considered two-way, _________ is necessary a. channel b. message c. noise d. feedback e. circuit

Which of the following is NOT one of the 3 technology bets we have made?
Artificial intelligence
Data analytics
Design Thinking
Digital core

Equipment consisting of busbars mounted inside an enclosure that provides a means of tapping the service-entrance conductors is called a

Compute the theoretical density of diamond given that the C-C distance and bond angle are 0.154 nm and 109.5o, respectively. The atomic weight of carbon is 12.01 g/mol.

Please explain the term ‘causal link’. What is the importance of the causal link
in work accidents? What kind of situations breaks the causal link? Explain all
situations with examples.

4. When the ESC system senses oversteer,
A) the brake at the inner rear or front wheel is applied to neutralize the oversteering
B) the brake at the outer corner rear or front wheel is applied to neutralize the oversteering

What is the biggest poop table ever recorded

Which of these processes uses a die and a press to form parts?

A) Stamping

B) Tailor-rolling

C) Hydroforming

D) Tailor-welding

With direct fuel injection the gasoline is injected:

why do kitchen cabinets bathtubs and attic openings require special framing details

A coastal engineer is to an oil platform as a structural engineer is to:

a freeway.

a skyscraper.

submarine pipelines.

an underground tunnel.

What is the main purpose of the alternater

Select the correct answer. Which of the following devices is a simple machine? A.
an engine
B.
a pulley
C.
a motor
D.
a bicycle
E.
a crane

what causes your car to eventually slow down and stop when you take your foot off the gas pedal

A textile fiber manufacturer is investigating a new drapery yarn, which the company claims has a mean thread elongation of 12 kilograms with a standard deviation of 0. 5 kilograms. The company wishes to test the hypothesis H0:μ=12 against H1:μ<12 using a random sample of n=4 specimens. Calculate the P-value if the observed statistic is x⎯⎯=11. 25. Suppose that the distribution of the sample mean is approximately normal. Round your final answer to five decimal places (e. G. 98. 76543). Enter your answer in accordance to the question statement