A solid uniform disk of mass Md and radius Rd and a uniform hoop of mass Mh and radius Rh are released from rest at the same height on an inclined plane. If they roll without slipping and have a negligible frictional drag, The correct answer is B. The disk will reach the bottom first.
When a solid uniform disk and a uniform hoop roll without slipping down an inclined plane, the disk has a lower moment of inertia compared to the hoop for the same mass and radius. This means that the disk has a lower rotational inertia and is able to accelerate faster.
Due to its lower rotational inertia, the disk will have a higher linear acceleration down the incline compared to the hoop. As a result, the disk will reach the bottom of the incline first.
To know more about inclined plane
https://brainly.com/question/29360090
#SPJ11
Use the following diagram to answer the next two questions: The quantity represented by the number 1 in the diagram is: 3. n= the order of the bright fringe b. λ= the wavelength of the light c. d= the distance between the two slits d. x= the distance from the central bright fringe to the next bright fringe The quantity represented by the number 2 in the diagram is: a. d= distance between the two slits b. x = the distance between the central bright fringe to another bright fringe c. I= distance from the double slit to the screen d. λ= the wavelength of light Clear my choice
The quantity represented by the number 1 in the diagram is x = distance from the central bright fringe to the next bright fringe and the quantity represented by the number 2 in the diagram is d = distance between the two slits.
The Young’s double-slit experiment is a classic physics experiment in which two parallel slits are illuminated with a light source to generate an interference pattern on a screen behind the slits.
The diagram shown below represents a bright fringe pattern generated by a double-slit arrangement:
Figure shows double slit diffraction pattern.
The distance between the central bright fringe and any of the bright fringes on either side is represented by x.
Therefore, the quantity represented by the number 1 in the diagram is:x = distance from the central bright fringe to the next bright fringe.
The distance between the two slits is represented by d. Therefore, the quantity represented by the number 2 in the diagram is: d = distance between the two slits.
Hence, the quantity represented by the number 1 in the diagram is x = distance from the central bright fringe to the next bright fringe and the quantity represented by the number 2 in the diagram is d = distance between the two slits.
Learn more about Young’s double-slit here:
https://brainly.com/question/29885741
#SPJ11
A 30-kg boy puts his entire weight on the small plunger of a hydraulic press. What weight can the larger piston lift if the diameters of both pistons are 1 cm and 12 cm?
The larger piston can lift a weight of 1686.42 N
The ratio of the diameter of the larger piston to the diameter of the smaller piston is 12: 1. So the ratio of the area of the larger piston to the area of the smaller piston will be (12/1)² : 1² = 144:1.
Therefore, the larger piston can lift a weight that is 144 times heavier than the weight placed on the smaller piston. Now, the smaller piston has a surface area of: (1/2)²π = 0.785 sq cm. So, if the 30 kg boy puts his entire weight on the small plunger, then the force exerted on the small plunger will be 30 kg x 9.8 m/s² = 294 N. And, this force will act over the surface area of the small plunger.
Thus, the pressure in the system will be: Pressure = Force / Area of the small piston = 294 N / 0.785 sq cm = 374.52 N/sq cm. And, this pressure will be transmitted uniformly throughout the hydraulic system.
Finally, using the formula: Pressure = Force / Area of the large piston, we can calculate the weight that the larger piston can lift.
So, the weight that the larger piston can lift will be:
Force = Pressure x Area of the large piston = 374.52 N/sq cm x (6 cm)²π / 4 = 1686.42 N.
So, the larger piston can lift a weight of 1686.42 N if the diameters of both pistons are 1 cm and 12 cm.
Know more about weight here,
https://brainly.com/question/31659519
#SPJ11
Slits are separated by 0.1mm. The screen is 3.0m from the source what is the wavelength (8 nodal lines) (d=10cm)
Slits are separated by 0.1mm. The screen is 3.0m from the source what is the wavelength. , the wavelength of light in this double-slit interference pattern is approximately 1.25 x 10^(-5) m.
To determine the wavelength of light given the separation between slits and the distance to the screen, we can use the equation for the location of the nodal lines in a double-slit interference pattern:
d * sin(θ) = m * λ
Where:
d is the separation between the slits (0.1 mm = 0.1 x 10^(-3) m)
θ is the angle between the central maximum and the m-th nodal line
m is the order of the nodal line (m = 8 in this case)
λ is the wavelength of light (to be determined)
We can rearrange the equation to solve for λ:
λ = d * sin(θ) / m
The angle θ can be approximated using the small-angle approximation:
θ ≈ x / L
Where x is the distance from the central maximum to the m-th nodal line (given as 10 cm = 0.1 m), and L is the distance from the source to the screen (3.0 m).
Substituting the known values:
θ ≈ 0.1 m / 3.0 m
θ ≈ 0.0333
Now we can substitute these values into the equation to calculate the wavelength:
λ = (0.1 x 10^(-3) m) * sin(0.0333) / 8
Calculating the value:
λ ≈ 1.25 x 10^(-5) m
Therefore, the wavelength of light in this double-slit interference pattern is approximately 1.25 x 10^(-5) m.
Learn more about double-slit interference pattern here:
https://brainly.com/question/31807318
#SPJ11
Sketch the optical absorption coefficient (a) as a function of photon energy (hv) for (i) a direct bandgap semiconductor and (ii) an indirect bandgap semiconductor. Please explain what information you can get from this sketch.
The absorption coefficient is maximum at the bandgap energy. For the direct bandgap semiconductor, the absorption coefficient is high at a lower energy level compared to the indirect bandgap semiconductor. It is because the direct bandgap semiconductors have a shorter carrier lifetime and denser electronic states. The absorption coefficient can be related to the strength of light absorption and the thickness of the material through the Beer-Lambert law.
The Beer-Lambert law states that the intensity of light decreases exponentially as it travels through a medium. The strength of the absorption is proportional to the optical path length of the light in the material, which is determined by the material's thickness. The absorption coefficient is proportional to the rate of electron-hole pairs created by incident photons. The absorption coefficient is high at the bandgap energy because the absorption of a photon with energy equal to or greater than the bandgap energy produces an electron-hole pair in the material, leading to a high rate of absorption of light.
Learn more about Beer Lambert's Law:
https://brainly.com/question/8831959
#SPJ11
For two otherwise identical houses, will the house with the higher R value walls or the lower R value walls conserve its heat more effectively? Write in the symbol that stands for the total amount of a fossil fuel resource over all time from its discovery to its exhaustion. What is used to concentrate sunlight so that it can power a heat engine? Is biomass used to produce ethanol as a fuel for automobiles? Yes or No? Of the various greenhouse gases that exist, which one is increasing due to human activity and primarily causing the mean global temperature to rise? What is the name for the sum of the average difference between the temperature outside and 65° F each day summed over all the days of the heating season? Name one of the three major nuclear power plant accidents that have occurred (correct spelling is not necessarily required for this answer).
For two otherwise identical houses, the house with the higher R-value walls will conserve its heat more effectively. The R-value is a measure of the thermal resistance of a material, and a higher R-value indicates better insulation and reduced heat transfer.
The symbol that stands for the total amount of a fossil fuel resource over all time from its discovery to its exhaustion is "U" for ultimate recoverable resources.
To concentrate sunlight so that it can power a heat engine, a device called a "solar concentration" is used.
Yes, biomass is used to produce ethanol as a fuel for automobiles.
Of the various greenhouse gases that exist, carbon dioxide (CO2) is increasing due to human activity and primarily causing the mean global temperature to rise.
The name for the sum of the average difference between the temperature outside and 65°F each day summed over all the days of the heating season is "degree days."
One of the three major nuclear power plant accidents that have occurred is the "Chernobyl disaster" in 1986.
To learn more about biomass visit: https://brainly.com/question/82777
#SPJ11
A certain measuring instrument can measure lengths as short as 0.000000300 m. Write this length with the appropriate prefix.
A certain measuring instrument can measure lengths as short as 0.000000300 m. The length can be written with the appropriate prefix, which is the picometer (pm).
One picometer is equivalent to 1×10−12 meter or 0.000000000001 meter (1 trillionth of a meter).
The prefix "pico-" denotes a factor of 10−12 (0.000000000001). Therefore, 0.000000300 m can be written as 300 pm. This means that the measuring instrument can measure lengths up to 300 picometers or 0.0000000003 meters in length.
In summary, a certain measuring instrument can measure lengths as short as 0.000000300 m, which is equivalent to 300 picometers (pm).
To learn more about picometer refer:-
https://brainly.com/question/13493801
#SPJ11
Please answer the following questions in detail:
1. What is the relation between the voltage the plate charge (top) and the capacitance? Explain and provide and equation.
2. How does the Capacitance vary with the area and separation ? Explain and provide and equation.
3. Calculate the electric field and the stored energy when the distance (separation between the plates) are 5.0mm and 10.0mm. (Show your work). When d= 5.00 mm then: V = 1.012 V, Area= 100 mm², Plate Charge= 1.79E-13 C, Capacitance= 0.18E-12 F. When d=10 mm then: V= 2.024 V, Area= 100 mm², Plate charge= 1.79E-13 C, Capacitance= 0.09E-12 F
What is the relation between the voltage the plate charge (top) and the capacitance?:
Capacitance is directly proportional to the plate area and inversely proportional to the distance between the plates. The greater the capacitance, the more plate charge a capacitor can hold at a specified voltage. The greater the voltage, the more charge the capacitor can hold. The capacitance is calculated using the following equation:
C= (εA)/d, where C is capacitance, ε is the dielectric constant of the material between the plates, A is the plate area, and d is the distance between the plates.
The plate charge is calculated using the equation Q= CV, where Q is plate charge, C is capacitance, and V is the voltage.
2. The variation of capacitance with area and separation:
The capacitance of a parallel-plate capacitor is directly proportional to the surface area of the plates and inversely proportional to the distance between them.
The formula for capacitance is C= ε(A/d), where ε is the permittivity of free space, A is the surface area of one plate, and d is the distance between the plates. Capacitance is proportional to the plate area and inversely proportional to the plate separation.
3. Calculation of electric field and stored energy:
d = 5.0 mm, V = 1.012 V, A = 100 mm², Plate charge = 1.79 × 10⁻¹³ C, Capacitance = 0.18 × 10⁻¹² F.ε₀ = 8.85 × 10⁻¹² F/m
Electric field = V/d = 1.012/0.005 = 202.4 V/m
Stored energy = 1/2CV² = 0.5 × 0.18 × 10⁻¹² × (1.012)² = 9.07 × 10⁻¹⁴ J
When d = 10.0 mm, V = 2.024 V, A = 100 mm², Plate charge = 1.79 × 10⁻¹³ C, Capacitance = 0.09 × 10⁻¹² F
Electric field = V/d = 2.024/0.01 = 202.4 V/m
Stored energy = 1/2CV² = 0.5 × 0.09 × 10⁻¹² × (2.024)² = 18.4 × 10⁻¹⁴ J
Therefore, the electric field for both situations is 202.4 V/m. The stored energy when the separation is 5.0 mm is 9.07 × 10⁻¹⁴ J, and when the separation is 10.0 mm, it is 18.4 × 10⁻¹⁴ J.
Learn more about capacitance here: https://brainly.com/question/21851402
#SPJ11
A uniform wooden meter stick has a mass of m = 837 g. A clamp can be attached to the measuring stick at any point P along the stick so that the stick can rotate freely about point P, which is at a distance d from the zero-end of the stick as shown.
a. Enter a general expression for the moment of inertia of a meter stick /e of mass m in kilograms pivoted about point P, at any distance din meters from the zero-cm mark.
b. The meter stick is now replaced with a uniform yard stick with the same mass of m = 837 g. Calculate the moment of inertia in kg m2 of the yard stick if the pivot point P is 50 cm from the end of the yardstick.
a. The moment of inertia of a meter stick of mass m in kilograms pivoted about point P, at any distance d in meters from the zero-cm mark can be represented by the general expression: `I = (1/3)md²`.
b. The moment of inertia of a yard stick of mass m = 837 g and length 1 yard = 3 feet = 36 inches is 0.0151 kg m².
a. The moment of inertia of a meter stick of mass m in kilograms pivoted about point P, at any distance d in meters from the zero-cm mark can be represented by the general expression:
`I = (1/3)md²`
Where,`
m = 837 g = 0.837 kg`and
`d`is the distance from the zero-cm mark to the pivot point P in meters.
b. The moment of inertia of a yard stick of mass m = 837 g and length 1 yard = 3 feet = 36 inches can be calculated as follows:`
Length of yardstick = 1 yard = 3 feet = 36 inches
`The distance from the end of the yardstick to the pivot point P = 50 cm = 0.5 m
The distance from the pivot point P to the center of mass of the yardstick is:
`L/2 = (36/2) in = 18 in = 0.4572 m`
The moment of inertia of the yardstick can be calculated as follows:
I = Icenter of mass + Imass of the stick around the center of mass
Assuming that the yardstick is thin and has negligible thickness, the moment of inertia of the yardstick around the center of mass can be calculated using the parallel axis theorem.`
Icenter of mass = (1/12)M(L²) = (1/12)(0.837)(0.4572)² = 0.0136 kg m²`
`Imass of the stick around the center of mass = Md²`where`d = 0.5 - 0.4572 = 0.0428 m`
`Imass of the stick around the center of mass = (0.837)(0.0428)² = 0.0015 kg m²`
Therefore, the moment of inertia of the yardstick about the pivot point P is given by:
I = 0.0136 + 0.0015 = 0.0151 kg m².
Learn more about moment of inertia https://brainly.com/question/14460640
#SPJ11
When water is brought to geat depthe due to subduction at 5 rubduction sone, it is put under enough containg pressure that it causes the tocks arpund it to melt: Tnue Out of the eight most common silicate minerals, quartz has the most amount of silicon. True False
When water is brought to great depths due to subduction at the 5 rubduction zone, it is put under enough containing pressure that it causes the rocks around it to melt.
This melted rock is known as magma, and when it cools down and solidifies, it forms igneous rock. As for the statement "Out of the eight most common silicate minerals, quartz has the most amount of silicon," it is false.
Subduction is the geological process in which one lithospheric plate moves beneath another lithospheric plate. This process usually takes place along the boundary of two converging plates. When one of these plates is an oceanic plate, it can be forced to subduct beneath the other plate. The area where this subduction takes place is known as the subduction zone.
At these subduction zones, water can be brought to great depths due to the process of subduction. This water is usually found in sediments that are piled up on top of the sinking plate. As the plate sinks deeper, the temperature and pressure around it increases. When the water reaches a depth of around 100 kilometers, it is put under enough containing pressure that it causes the rocks around it to melt.
This melted rock is known as magma, and when it cools down and solidifies, it forms igneous rock.Silicon is one of the most abundant elements in the Earth's crust. It is usually found in the form of silicate minerals, which are made up of silicon, oxygen, and other elements.
Quartz is one of the most common silicate minerals and is made up of silicon dioxide. However, it is not correct to say that quartz has the most amount of silicon. Out of the eight most common silicate minerals, feldspar is the one that has the most amount of silicon.
When water is brought to great depths due to subduction at the 5 rubduction zone, it is put under enough containing pressure that it causes the rocks around it to melt, forming magma. As for the statement "Out of the eight most common silicate minerals, quartz has the most amount of silicon," it is false. The mineral feldspar is the one that has the most amount of silicon.
To know more about igneous rock :
brainly.com/question/2500550
#SPJ11
A copper wire is stretched with a stress of 50MPa at 20 ∘
C. If the length is held constant, to what temperature must the wire be heated to reduce the stress to 20MPa ? The value of α 1
for copper is 17.0×10 −6
( ∘
C) −1
, the modulus of elasticity is equal to 110 GPa. ∘
C
A copper wire is stretched with a stress of 50MPa at 20 ∘C. the change in temperature (ΔT') needed to reduce the stress to 20 MPa is equal to the initial temperature difference (ΔT).
To calculate the change in temperature (ΔT') needed to reduce the stress to 20 MPa, we need to use the values of the coefficient of linear expansion (α) for copper and the given values of stress (50 MPa and 20 MPa).
The coefficient of linear expansion for copper (α) is provided as 17.0 × 10^(-6) (°C)^(-1).
Let's assume the initial temperature of the copper wire is T1 and the final temperature is T2.
We can write the equation as:
ΔT' = (α * ΔT) / α'
Given:
α = 17.0 × 10^(-6) (°C)^(-1)
ΔT = T2 - T1
Since the stress is inversely proportional to the coefficient of linear expansion, we can write:
ΔT' = (α * ΔT1) / α2 = (α2 / α) * ΔT
Substituting the given values, we get:
ΔT' = (17.0 × 10^(-6) / 17.0 × 10^(-6)) * ΔT = ΔT
Therefore, the change in temperature (ΔT') needed to reduce the stress to 20 MPa is equal to the initial temperature difference (ΔT).
To find the actual temperature to which the copper wire must be heated, we would need to know the initial temperature (T1) of the wire.
Learn more about coefficient of linear expansion here:
https://brainly.com/question/14780533
#SPJ11
Use this circuit to answer the first set of questions: R1 R3 220 Ω 220 Ω 220 Ω R2 R4 220 Ω www +1 PSB 5 V • What is the total resistance in the circuit? (Remember that when measuring resistance, the components must not be connected to the PSB.) • What is the total voltage across the series of resistors? • What is the voltage across each of the resistors in the series? • What is the voltage when measuring at each of the location sets shown below (A, B, and C)? R3 R2 R1 220 R2 220 R3 220 R4 220 R1 2200 R2 2200 R4 220 R1 2200 R3 2200 R4 220 ܤܢܬ݁ܐܬ݁ܦܶ wwwwww + + PSB 5V PSB SV PSB SV Question 3 1 pts How much total current will flow through the circuit in Part 1? Total current is each resistor added together, so approximately 880 N. The current is 3.3V = 88012 (the total resistance), so approximately 3.8mA. The current is 5V + 2200 because all the resistors are equal, so approximately 22.7mA. The current is 5V +88012 (the total resistance), so approximately 5.7mA. Question 4 2 pts How much current will flow through each resistor in Part 1? Resistance limits current, so each resistor will have approximately 2201. The current through each component in a series must be the same, so the total current of about 5.7mA will flow through each resistor. Since the resistors have equal value, the current through each resistor will be the same, 5V = 22012, or approximately 227mA. The current will be divided equally among resistors of equal value, so 1/4 of the total current will flow through each resistor. Question 5 3 pts Match the voltage measurements from the resistor series in Part 1 with the approximate values below. You may use the same answer more than once. A: Voltage across R1. B: Voltage across R2 + R3 + R4. [Choose ] 2200 3.3V 2.5V 3.75V 825mV 660Ω 44022 1.25V 5V C: Voltage across R3 + R4. Question 6 2 pts Based on your observations in Part 1 (as well as previous labs), select both of the TRUE statements about voltage and resistors in series below. (2 answers) Resistors in series divide voltage proportionally depending on the relative value of each resistor, meaning the highest voltage will be across the highest value resistor and the lowest voltage will be across the lowest value resistor. Resistors in series divide voltage proportionally depending on their order (R1 has higher votage, R2 has less, and so on). Resistors in series reduce total resistance by adding distance to the path, so more charge can flow. | The voltage across each resistor in a series will be inversely proportionate to its resistance, meaning the highest voltage will be across the lowest value resistor and the lowest voltage will be across the highest value resistor. Resistors in series will divide voltage equally, with the total voltage determined by the total resistance. Resistors in series add to total resistance in a path.
Answers: (a) The total resistance = 880 Ω.
(b) The total voltage = 5V
(c) voltage across each of the resistors= 0.0057V
(d) Voltage across R1=1.25V
Voltage across R2 + R3 + R4= 3.75V
Voltage across R3 + R4= 2.5V
(e) Total current in Part 1 = 0.0057 A.
(f) The current that will flow through each resistor in Part 1 = 0.0014 A.
(a) The total resistance in the circuit is equal to the sum of resistance of each component present in it.
R1 + R2 + R3 + R4 = 220 + 220 + 220 + 220 = 880 Ω.
(b) The total voltage across the series of resistors is equal to the voltage of the power source that is connected across the circuit. So, the total voltage across the series of resistors is 5 V.
(c) As the resistance of all the resistors is the same, therefore the voltage across each of the resistors will be the same. Therefore, the voltage across each of the resistors in the series will be equal to the total voltage divided by the total resistance. Voltage across each of the resistors = Total voltage / Total resistance = 5 / 880 = 0.0057V
(d) The voltage at each of the location sets can be calculated as follows:
A: Voltage across R1 = Voltage across the series of resistors × (R1 / Total resistance)= 5 × (220 / 880) = 1.25 V
B: Voltage across R2 + R3 + R4 = Voltage across the series of resistors × (R2 + R3 + R4 / Total resistance)
= 5 × (220 + 220 + 220 / 880) = 3.75 V
C: Voltage across R3 + R4 = Voltage across the series of resistors × (R3 + R4 / Total resistance)
= 5 × (220 + 220 / 880) = 2.5 V.
(e) Total current is the current that flows through the circuit when the power source is connected across can be calculated as follows: Total current = Total voltage / Total resistance= 5 / 880 = 0.0057 A. Therefore, the total current that will flow through the circuit in Part 1 is 0.0057 A.
(f) Since all the resistors have the same value, therefore the current will be divided equally among them. So, the current that will flow through each resistor in Part 1 is equal to the total current divided by the total number of resistors. Therefore, the current that will flow through each resistor in Part 1 is 0.0057 / 4 = 0.0014 A.
Learn more about resistors: https://brainly.com/question/24858512
#SPJ11
A particle is moving toward the origin along the positive direction of the X axis. The displacement of this particle is negative. O it depends on the speed. O positive. O it depends on the frame of reference.
The displacement of a particle moving towards the origin in the positive direction of the x-axis is negative.
A frame of reference is a coordinate system in which motion is observed. In the case of a particle moving towards the origin in the positive direction of the x-axis, the displacement is negative.The displacement of a particle moving towards the origin in the positive direction of the x-axis is negative.
A frame of reference is a coordinate system in which motion is observed. In the case of a particle moving towards the origin in the positive direction of the x-axis, the displacement is negative.If we assume that the particle is moving with a uniform speed, the displacement is negative in all reference frames.
If the particle moves faster or slower with respect to the reference frame, its displacement may be positive or negative.
However, the speed is constant in all reference frames. In the case of a particle moving towards the origin along the positive direction of the x-axis, the displacement is always negative regardless of the reference frame. It is the direction of motion that determines the sign of the displacement.
Know more about displacement here,
https://brainly.com/question/11934397
#SPJ11
You are viewing two light sources of the same size at the same distance. One is 1900.0 K and the other is 4900.0 K. How many times brighter is the hotter light source?
The
intensity of light
emitted by an object is proportional to the fourth power of its temperature.
Therefore, the hotter light source is much brighter than the cooler light source by a significant factor. To determine how much brighter, we must first calculate the ratio of their
intensities
.The Stefan-Boltzmann law states that the amount of energy emitted by a black body is proportional to the fourth power of its absolute
temperature
. Hence, we have,$I∝T^4$$\frac{I_1}{I_2}=\frac{(T_1/T_2)^4}{1}$ where I1 and I2 are the intensities of light from the two sources, T1 and T2 are their temperatures, respectively. Substituting the values in the equation, we have:$\frac{I_1}{I_2}=\frac{(4900.0/1900.0)^4}{1}$Calculating the ratio,$$\frac{I_1}{I_2} \approx 46.49$$Therefore, the hotter light source is approximately 46.49 times brighter than the cooler light source.
Thus, we can conclude that the hotter light source is much brighter than the cooler light source by a factor of about 46.5.
Learn more about
light source
https://brainly.com/question/14203870
#SPJ11
The hotter light source is approximately 56.9 times brighter than the cooler light source. So, the hotter light source is about 56.9 times brighter than the cooler light source.
The brightness of a light source is determined by its temperature, which is measured in Kelvin (K). To compare the brightness of two light sources, we can use the Stefan-Boltzmann law, which states that the total power radiated by a blackbody is proportional to the fourth power of its temperature.
In this case, we have two light sources of different temperatures: 1900.0 K and 4900.0 K. To find out how many times brighter the hotter light source is, we can calculate the ratio of their powers.
The ratio of the powers is given by the equation:
[tex](4900.0/1900.0)^4[/tex]
It is important to note that this calculation assumes that both light sources have the same size and are at the same distance. Additionally, the Stefan-Boltzmann law applies to idealized blackbodies, which may not perfectly represent all real light sources. However, it provides a useful approximation for comparing the brightness of light sources.
Learn more about light source
https://brainly.com/question/14203870
#SPJ11
When moving on level ground, cross-country skiers slide their skis along the snow surface to stay moving. The coefficients of friction for a given set of skis and given snow conditions can be modified by various types of waxes. Part A In order to move across the snow as fast as possible should you choose a wax that makes the coefficient of static friction between skis and snow as high as possible or as low as possible? O Choose wax that makes the coefficient of static friction between skos and snow as low as possible Choose wax that makes the coefficient of static friction between skis and snow as high as possible. Submit Request Answer Part B Should you choose a wax that makes the coefficient of kinetic friction between these two surfaces as high as possible or as low as possible? O Choose wax that makes the coefficient of kinetic friction between these two surfaces as high as possible. O Choose wax that makes the coefficient of kinetic friction between these two surfaces as low as possible
The answer to this question is as follows:
Part A - The wax chosen should make the coefficient of static friction between skis and snow as low as possible. The lower the static friction coefficient, the easier it is to overcome the forces that keep the skis at rest and start moving.
Part B - The wax chosen should make the coefficient of kinetic friction between these two surfaces as low as possible. The lower the kinetic friction coefficient, the easier it is to keep moving once you have started.
Coefficient of friction is defined as the ratio of the force required to move one surface over another surface to the force that is pressing them together. In simple terms, it is the measure of how difficult it is to slide one object over another.
The lower the coefficient of friction between two surfaces, the easier it is to move one over the other. The snow ski race is one of the most popular sports that demonstrate this principle. In cross country ski racing, skiers slide their skis along the snow surface to stay moving.
To make the movement of skis easier, various types of waxes are used. When choosing a wax for skiing, it is important to understand the effect of different waxes on the coefficient of friction between the skis and snow surface.
Learn more about coefficient of static friction here
https://brainly.com/question/29216055
#SPJ11
the centre of earth is a distance of 1.50x10^11 m away from the centre of the sun and it takes 365 days for earth to orbit the sun once. what is the mass of the sun?
Therefore, the mass of the Sun is 1.99 x 1030 kg.
Given that the centre of the Earth is a distance of 1.50×1011 m away from the centre of the Sun, and it takes 365 days for Earth to orbit the Sun once. We are to find the mass of the Sun. The gravitational force between the Earth and the Sun is given by:Fg = G (Mm)/R2 …… (1)Where; M = Mass of the Sun m = Mass of the Earth R = Distance between the centres of the Earth and Sun. G = Universal gravitational constant. We know that Earth takes 365 days to complete one revolution around the Sun. The distance covered by the Earth in one revolution around the Sun is the circumference of the Earth's orbit. Circumference = 2πR ….. (2)The time taken to complete one revolution = 365 days = 365 × 24 × 60 × 60 seconds. Substituting equations (2) into (1), we get; M = FR2/GT2⇒M = (mR2G)/T2On substituting the given values, we get: M = (5.97 x 1024 kg x (1.50 x 1011 m)2 x 6.6743 x 10-11 N m2/kg2)/(365 x 24 x 60 x 60 s)2= 1.99 x 1030 kg. Therefore, the mass of the Sun is 1.99 x 1030 kg.
To know more about Sun visit:
https://brainly.com/question/14538663
#SPJ11
How much heat energy (in kJ) would be required to turn 12.0 kg of liquid water at 100°C into steam at 100°C?
The latent heat of vaporization for water is Lv= 2,260,000 J/kg.
Report the positive answer with no decimal places.
The heat energy required to turn 12.0 kg of liquid water at 100°C into steam at 100°C is 27,120 kJ.
To calculate the heat energy required to turn 12.0 kg of liquid water at 100°C into steam at 100°C, we need to consider two processes: heating the water from 100°C to its boiling point and then converting it into steam.
First, we calculate the heat energy required to heat the water from 100°C to its boiling point. The specific heat capacity of water is approximately 4,186 J/kg·°C. Therefore, the heat energy required for this process can be calculated using the equation:
Q1 = m * c * ΔT1
where Q1 is the heat energy, m is the mass of water, c is the specific heat capacity of water, and ΔT1 is the change in temperature. In this case, ΔT1 = (100°C - 100°C) = 0°C, so Q1 = 0 J.
Next, we calculate the heat energy required for the phase change from liquid to steam. The latent heat of vaporization (Lv) for water is given as 2,260,000 J/kg. Therefore, the heat energy required for this process is:
Q2 = m * Lv
where Q2 is the heat energy and m is the mass of water. Substituting the values, Q2 = 12.0 kg * 2,260,000 J/kg = 27,120,000 J.
Converting the result from joules to kilojoules, we have Q2 = 27,120,000 J = 27,120 kJ.
Learn more about magnetic field here:
https://brainly.com/question/29210982
#SPJ11
The G Key below middle C on a piano keyboard vibrates with a
frequency of 390Hz. Determine the period of vibration.
The period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Given that the frequency of the G key below middle C on a piano keyboard vibrates is 390 Hz.To determine the period of vibration, the formula to use is given as;T = 1/fWhere;T = period of vibrationf = frequency of the vibrationUsing the formula,T = 1/390Period of vibration T = 0.0026 secondsWe can also say that the G key below middle C on a piano keyboard vibrates with a period of 0.0026 seconds.Therefore, the period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Learn more about Frequency here,
https://brainly.com/question/254161
#SPJ11
A simple series circuit consists of a 190 Ω resistor, a 28.0 V battery, a switch, and a 1.70 pF parallel-plate capacitor (initially uncharged) with plates 5.0 mm apart. The switch is closed at t =0s . Find the displacement current at t =0.50ns .
A simple series circuit consists of a 190 Ω resistor, a 28.0 V battery, a switch, and a 1.70 pF parallel-plate capacitor the displacement current at t = 0.50 ns will be zero since there is no change in electric flux through the capacitor plates.
To find the displacement current at t = 0.50 ns in the given circuit, we need to determine the rate of change of electric flux through the capacitor plates.
The displacement current (Id) can be calculated using the formula: Id = ε₀ × (dΦE / dt), where ε₀ is the permittivity of free space, dΦE/dt is the rate of change of electric flux through the capacitor.
In this case, the capacitor is initially uncharged, so there is no electric field (E) between the plates. Therefore, the electric flux through the capacitor is initially zero, and its rate of change is also zero.
Since the switch is closed at t = 0s, it will take some time for the capacitor to charge up and establish an electric field between its plates. At t = 0.50 ns, the capacitor is still in the process of charging, and the electric field has not fully developed.
As a result, the displacement current at t = 0.50 ns will be zero since there is no change in electric flux through the capacitor plates. Once the capacitor is fully charged and the electric field is established, the displacement current will start to flow, but at t = 0.50 ns, it is still not present.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
. A ray of light traveling in transparent material 1 with index of refraction n 1
=1.20 makes an angle θ 1
=51.0 ∘
with the normal to a flat interface with transparent material 2, which has index of refraction n 2
=1.70, as shown. What is the angle of refraction θ 2
? A. 68.1 ∘
B. 37.5 ∘
C. 29.1 ∘
D. 33.3 ∘
The angle of refraction θ2 with respect to the surface is 45.76°.Therefore, the correct option is (A) 68.1 ∘.
When a ray of light travels from one medium to another, it bends, this is known as refraction. The angle of refraction is given by Snell's law that states that the ratio of the sine of the angle of incidence to the sine of the angle of refraction is equal to the ratio of the refractive indices of the two media.
Here, the incident ray of light is traveling in transparent material 1 with an index of refraction n1=1.20. It makes an angle θ1=51.0∘ with the normal to a flat interface with transparent material 2, which has an index of refraction n2=1.70.Now, we need to find the angle of refraction θ2.The correct option is (A) 68.1 ∘
According to Snell's law, we can write that,n1 sin θ1 = n2 sin θ2n1=1.20, θ1=51.0∘, n2=1.70Let's put these values in Snell's law and calculate the value of θ2.n1 sin θ1 = n2 sin θ2sin θ2 = n1 / n2 sin θ1sin θ2 = 1.20 / 1.70 sin 51.0sin θ2 = 0.70sin θ2 = sin -1 (0.70)θ2 = 44.24°The angle of refraction is θ2 = 44.24°.
However, this angle is measured with respect to the normal. But the question asks about the angle of refraction with respect to the surface, which is given by (90 - θ2) = (90 - 44.24) = 45.76°.
Therefore, the angle of refraction θ2 with respect to the surface is 45.76°.Therefore, the correct option is (A) 68.1 ∘.
Learn more about refraction here,
https://brainly.com/question/27932095
#SPJ11
Select all the correct answers. Which two types of waves can transmit energy through a vacuum? a. radio waves b. seismic waves c. sound waves d. water waves
e. x-rays
a. Radio waves
e. X-rays
Radio waves and X-rays are the two types of waves that can transmit energy through a vacuum.
1. Radio waves: Radio waves are a type of electromagnetic wave that can travel through a vacuum. They have long wavelengths and low frequencies, typically used for communication and broadcasting.
2. X-rays: X-rays are another type of electromagnetic wave that can pass through a vacuum. They have much shorter wavelengths and higher frequencies compared to radio waves. X-rays are commonly used in medical imaging and industrial applications.
The other options listed, seismic waves, sound waves, and water waves, require a medium (such as air, water, or solid materials) to propagate and transfer energy. These waves rely on the interaction and transmission of particles within the medium for their propagation.
3. Seismic waves: Seismic waves are generated by earthquakes and other geological phenomena. They require the presence of solid or fluid materials, such as the Earth's crust or water bodies, to propagate. Seismic waves cannot travel through a vacuum.
4. Sound waves: Sound waves are mechanical waves that require a medium, typically air or other gases, liquids, or solids, for their transmission. They propagate through the vibration and compression of particles in the medium. Sound waves cannot travel through a vacuum.
5. Water waves: Water waves, also known as surface waves or ocean waves, are a type of mechanical wave that propagates on the surface of water bodies. They require the presence of water as a medium for their transmission. Water waves cannot travel through a vacuum.
In summary, only electromagnetic waves, such as radio waves and X-rays, have the ability to transmit energy through a vacuum. Mechanical waves like seismic waves, sound waves, and water waves require a medium and cannot propagate in a vacuum.
Learn more about Radio waves here :-
https://brainly.com/question/13989450
#SPJ11
&=8.854x10-¹2 [F/m] Ao=4r×107 [H/m] 16) A Hertzian dipole antenna, placed in free space, has a radiation resistance of 492 when it is connected to a 100 MHz source. The length of this antenna equals: a) 1.52 cm b) 5.09 cm c) 14.3 cm d) 21.4 cm e) None of the above. 18) An air-filled 3cmx1cm rectangular metallic waveguide operates at 15.5 GHz. The number of propagating TM modes equals: a) 1 b) 2 c) 3 d) 4 e) None of the above.
Question 16: The length of the antenna equals 7.54 cm, the correct option is (e) None of the above.
Question 18: There will be no propagating modes, the correct option is (e) None of the above.
Question 16: A Hertzian dipole antenna, placed in free space, has a radiation resistance of 492 when it is connected to a 100 MHz source. The length of this antenna equals
Given,
A Hertzian dipole antenna is placed in free space
The radiation resistance of the antenna when it is connected to a 100 MHz source is 492
We know that the radiation resistance of a short dipole antenna is given by
[tex]R_{r}[/tex] = 80π²r²/λ²,
where, r = length of the antenna, λ = wavelength of the radiation.
Rearranging, r = λ/4 × √([tex]R_{r}[/tex]/π²)……..(1)
The formula for the wavelength is given by
λ = c/f
where, c = speed of light, f = frequency of the radiation.
Putting the values,
λ = 3 × 10⁸/100 × 10⁶ = 3 m
Putting the value of λ in equation (1),
r = 3/4 × √(492/π²) = 0.0754 m = 7.54 cm
Therefore, the length of the antenna equals 7.54 cm.
Hence, the correct option is (e) None of the above.
Note: The given radiation resistance is of a Hertzian dipole antenna but the question is asking the length of a short dipole antenna. So, we have used the formula for a short dipole antenna.
Question 18: An air-filled 3 cm x 1 cm rectangular metallic waveguide operates at 15.5 GHz. The number of propagating TM modes equals
Given,
Air-filled rectangular metallic waveguide has dimensions 3 cm x 1 cm
The operating frequency is 15.5 GHz.
We know that the maximum frequency of operation for TE₁₀ mode in a rectangular waveguide is given by
[tex]f_c[/tex] = c/2a……(1)
where, c = speed of light, a = width of the waveguide (minimum dimension).
The formula for the cut-off frequency of TM₁₀ mode is given by
[tex]f_c[/tex] = c/2b…….(2)
where, b = height of the waveguide (maximum dimension).
From equation (1), the width of the waveguide is given by
a = c/2[tex]f_c[/tex]
From equation (2), the height of the waveguide is given by
b = c/2[tex]f_c[/tex]
So, the cut-off frequency of TM₁₀ mode is given by
[tex]f_c[/tex] = c/2b = c/2a
We have given the values of a = 1 cm and b = 3 cm.
So, we can write
[tex]f_c[/tex] = c/2b = c/2a = 15.5 GHz
From the above equation, the cut-off frequency is 15.5 GHz which is the operating frequency of the waveguide.
So, there will be no propagating modes.
Therefore, the correct option is (e) None of the above.
Learn more about dipole antenna here:
https://brainly.com/question/17414859
#SPJ11
An green hoop with mass mh=2.6 kg and radius Rh=0.14 m hangs from a string that goes over a blue solid disk pulley with mass md=1.9 kg and radius Rd=0.1 m. The other end of the string is attached to a massless axel through the center of an orange sphere on a flat horizontal surface that rolls without slipping and has mass ms=4.1 kg and radius R5 =0.21 m. The system is released from rest. 1) What is magnitude of the linear acceleration of the hoop? m/s2 2) What is magnitude of the linear acceleration of the sphere? m/s2 3) What is the magnitude of the angular acceleration of the disk pulley? rad/s2 4) What is the magnitude of the angular acceleration of the sphere? rad/s2 5) What is the tension in the string between the sphere and disk pulley? N 6) What is the tension in the string between the hoop and disk pulley? N 7) The green hoop falls a distance d=1.57 m. (After being released from rest.) How much time does the hoop take to fall 1.57 m ? 5 8) What is the magnitude of the velocity of the green hoop after it has dropped 1.57 m ? m/s 9) What is the magnitude of the final angular speed of the orange sphere (after the green hoop has fallen the 1.57 m )? rad/s
1)Magnitude of the linear acceleration of the hoop= 9.8 m/s²2)the magnitude of the linear acceleration of the sphere is 0. 3)The magnitude of the angular acceleration of the disk pulley α = 0.4 m/s². 4)The magnitude of the angular acceleration of the sphere= 0.23 m/s². 5)The tension in the string between the sphere and disk pulleyT1 = 40.38 N. 6)The tension in the string between the hoop and disk pulleyT = 50.68 N.7)The hoop takes time to fall 1.57 m= 0.56 s. 8)the magnitude of the velocity of the green hoop v² = 6.2 m/s. 9)The magnitude of the final angular speed of the orange sphere is 29.5 rad/s.
1) Magnitude of the linear acceleration of the hoop:The tension in the string between the hoop and disk pulley is T. Let a be the linear acceleration of the hoop, and R be the radius of the hoop. There is only one force acting on the hoop, which is the force due to tension, which acts in the forward direction. Hence,mh * a = TThus, a = T / mh. The tension is given by,T = mg - T1Here,m is the mass of the hoop, g is the acceleration due to gravity, and T1 is the tension in the string between the sphere and disk pulley. Hence,a = (mg - T1) / mhGiven that,mh = 2.6 kgm = 9.8 m/s²g = 9.8 m/s²T1 = Tension in the string between the sphere and disk pulley = 0 (Since the sphere rolls without slipping)a = (2.6 × 9.8 - 0) / 2.6 = 9.8 m/s²
2) Magnitude of the linear acceleration of the sphere:Since the sphere rolls without slipping, the acceleration of the sphere is the same as the linear acceleration of its center of mass. Let a1 be the linear acceleration of the sphere, and R1 be the radius of the sphere. Let T1 be the tension in the string between the sphere and disk pulley. Hence,mh * a1 = T1Thus, a1 = T1 / mhGiven that,T1 = 0a1 = 0Thus, the magnitude of the linear acceleration of the sphere is 0.
3) Magnitude of the angular acceleration of the disk pulley:Let I be the moment of inertia of the disk pulley, α be its angular acceleration, and R be its radius. The disk pulley is rolling without slipping. Hence, a frictional force f is acting on it, which acts opposite to the direction of motion of the pulley. Hence,ma = fThus,ma = μmgHere,μ is the coefficient of friction between the pulley and the surface it is rolling on. Thus,α = a / R = μg / RThus,α = 0.4 m/s².
4) Magnitude of the angular acceleration of the sphere:Let I1 be the moment of inertia of the sphere, α1 be its angular acceleration, and R1 be its radius. Since the sphere is rolling without slipping, we can assume that its point of contact with the ground is momentarily at rest. Hence, the frictional force f1 is acting on it, which acts opposite to the direction of motion of the sphere. Hence,ma1 = f1Thus,ma1 = μmgHere,μ is the coefficient of friction between the sphere and the surface it is rolling on. Thus,α1 = a1 / R1 = μg / R1Thus,α1 = 0.23 m/s².
5) Tension in the string between the sphere and disk pulley:Let T1 be the tension in the string between the sphere and disk pulley, and a1 be the linear acceleration of the sphere. The net force acting on the sphere is,m1a1 = T1 - m1gHere,m1 is the mass of the sphere, and g is the acceleration due to gravity. Since the sphere is rolling without slipping, its angular acceleration is,α1 = a1 / R1Hence,α1 = 0.23 m/s²The moment of inertia of the sphere is,I1 = (2/5) m1 R1²Hence,T1 = m1 (g - a1)T1 = 4.1 (9.8 - 0)T1 = 40.38 N.
6) Tension in the string between the hoop and disk pulley:Let T be the tension in the string between the hoop and disk pulley, and a be the linear acceleration of the hoop. The net force acting on the hoop is,mh a = T - mh gHere,mh is the mass of the hoop, and g is the acceleration due to gravity. Hence,T = mh (g + a)T = 2.6 (9.8 + 9.8)T = 50.68 N.
7) Time taken by the hoop to fall a distance of 1.57 m:Let h be the distance fallen by the hoop, and t be the time taken to fall this distance. Hence,1/2 mgh = mh g h t/2 = sqrt (2h/g)t = sqrt (2 × 1.57 / 9.8)t = 0.56 s.
8) Magnitude of the velocity of the hoop after it has dropped 1.57 m:Let v be the velocity of the hoop after it has dropped 1.57 m. The final velocity of the hoop is given by,v² - u² = 2ghHere,u is the initial velocity of the hoop, which is 0. Hence,v² = 2ghv² = 2 × 9.8 × 1.57v = 6.2 m/s.
9) Magnitude of the final angular speed of the sphere:Let ω be the final angular speed of the sphere, v1 be its final linear velocity, and R1 be its radius. Since the sphere rolls without slipping,ω = v1 / R1Hence,ω = v / R1Here,v is the linear velocity of the hoop just before it hits the sphere. Hence,v = 6.2 m/sAlso,R1 = 0.21 mω = v / R1ω = 29.5 rad/sThus, the magnitude of the final angular speed of the orange sphere is 29.5 rad/s.
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
A coordinate system (in meters) is constructed on the surface of a pool table, and three objects are placed on the table as follows: a my = 1.4-kg object at the origin of the coordinate system, a m2 = 2.9-kg object
at (0, 2.0), and a mg = 4.5-kg object at (4.0, 0). Find the resultant gravitational force exerted by the other two objects on the object at the origin.
The resultant gravitational force exerted by the other two objects on the object at the origin of the coordinate system is approximately 1.22 N directed towards the positive y-axis.
To find the resultant gravitational force on the object at the origin, we need to calculate the gravitational force exerted by each of the other two objects and then determine their vector sum.
The gravitational force between two objects can be calculated using Newton's law of universal gravitation:
[tex]F = G * (m1 * m2) / r^2[/tex]
where F is the gravitational force, G is the gravitational constant (approximately 6.674 × 10^(-11) N·m^2/kg^2), m1 and m2 are the masses of the two objects, and r is the distance between them.
First, let's calculate the gravitational force exerted by the 2.9-kg object at (0, 2.0) on the 1.4-kg object at the origin. The distance between them is given by the y-coordinate:
r1 = 2.0 m
Using the formula, we get:
F1 = (6.674 × [tex]10^{(-11)[/tex] N·[tex]m^2/kg^2[/tex]) * ((1.4 kg) * (2.9 kg)) / [tex](2 m)^2[/tex]
F1 ≈ 2.13 N
The gravitational force is directed towards the positive y-axis.
Next, let's calculate the gravitational force exerted by the 4.5-kg object at (4.0, 0) on the 1.4-kg object at the origin. The distance between them is given by the x-coordinate:
r2 = 4.0 m
Using the formula, we get:
F2 = (6.674 ×[tex]10^{(-11)[/tex] N[tex]m^2/kg^2[/tex]) * ((1.4 kg) * (4.5 kg)) / [tex](4.0 m)^2[/tex]
F2 ≈ 1.88 N
The gravitational force is directed towards the positive x-axis.
To find the resultant force, we need to combine the individual forces as vectors. Since the forces are perpendicular to each other, we can use the Pythagorean theorem:
Resultant force = √[tex](F1^2 + F2^2)[/tex]
Resultant force = √[tex]((2.13 N)^2 + (1.88 N)^2)[/tex]
Resultant force ≈ 1.22 N
The resultant gravitational force exerted by the other two objects on the object at the origin is approximately 1.22 N directed towards the positive y-axis.
Learn About vector sum Here:
https://brainly.com/question/28343179
#SPJ11
The inductor in the RLC tuning circuit of an AM radio has a
value of 450 mH .
Part A: What should be the value of the variable capacitor in
the circuit to tune the radio to 730 kHz?
Express your answe
The value of the variable capacitor should be 185.2 pF to tune the radio to 730 kHz.To tune the radio to 730 kHz, the value of the variable capacitor should be 185.2 pF.
The inductor in the RLC tuning circuit of an AM radio has a value of 450 mH. What should be the value of the variable capacitor in the circuit to tune the radio to 730 kHz?The required value of the variable capacitor in the circuit to tune the radio to 730 kHz should be 185.2 pF (pico-farad).
How to calculate the value of the variable capacitor?
The resonant frequency of a series RLC circuit can be given by the formula,f = 1/(2π √(LC))Where,f = frequency in HertzL = Inductance in HenrysC = Capacitance in FaradsGiven that the inductance, L = 450 mH = 0.45 HFrequency, f = 730 kHz = 730000 HzThe formula can be rearranged to get the capacitance,C = 1/[(2πf)^2L]So, the capacitance, C = 1/[(2π × 730000)^2 × 0.45]C = 185.2 pFTherefore, the value of the variable capacitor should be 185.2 pF to tune the radio to 730 kHz.To tune the radio to 730 kHz, the value of the variable capacitor should be 185.2 pF.
Learn more about Frequency here,
https://brainly.com/question/254161
#SPJ11
nclined Plane Measurements
2. (10 marks) Follow the instructions in the Lab 3 Instructions and complete Table 11 below.
Record all measurements with two decimal places.
Table 1: Average speed/velocity measurements.
Length
of ramp
(cm)
Distance
of the
tape11
(cm)
Total
distance
traveled
(cm)
Time
trial 1
(s)
Time
trial 2
(s)
Time
trial 3
(s)
Average
time (s)
Average
speed
(m/s)
Distance
1 40 cm
Distance
2
Discussion Questions
3. (3 marks) What happens to the speed/velocity of the car from start to end? Explain using
Newton’s laws of motion.
4. (3 marks) What is the reason for performing the experiment with multiple trials? Why not let
the car run one time only and record the time?
Page 1 of 7
SCIE2060 Lab 3 Report Spring 2022
5. Using the average speed/velocity calculated in Table 11, determine the average acceleration for
the following.
Hint See the equations in the instructions to solve for a. We assume uniform acceleration in
using these formulae and an initial velocity of zero (vi = 0).
(a) (3 marks) Acceleration for Distance 1. Write the formula, show all of your work, include
units.
(b) (3 marks) Acceleration for Distance 2. Write the formula, show all of your work, include
units.
(c) (2 marks) Look at your answer in parts aa and bb. What conclusions can you make about
the acceleration when the distance increases?
Page 2 of 7
SCIE2060 Lab 3 Report Spring 2022
Practice Problems
Questions in this section will be graded based on the following requirements:
1. Write out the required formulae.
2. Show all your work. Round answers to two decimal places if necessary.
3. Include units.
4. Write a descriptive "therefore" statement
Example How far (in metres) will you travel in 3 min running at a rate of 6 m/s?
t = 3 min × 60 s/min = 180 s v = 6 m/s
Formula: v = d/t ✓
Inserting into the formula: 6 = d/180 ✓
d = 1080 m ✓
∴ You will travel 1080 m in 3 min at a rate of 6 m/s. ✓ 4 marks
6. (4 marks) A car travels a distance of 2750 m over 110 s. Calculate the velocity of the car.
7. (4 marks) A football is thrown horizontally with a speed of 28.0 m/s. How long does it take
the football to travel 16.3 m?
Page 3 of 7
SCIE2060 Lab 3 Report Spring 2022
8. A car moves along a straight highway at an average velocity of 112 km/h.
(a) (4 marks) How far will the car travel in 180 min?
(b) (4 marks) How long will it take to travel 200 km?
9. (4 marks) A car accelerates uniformly from rest over a time of 7.13 s for a distance of 163 m.
Determine the acceleration.
Page 4 of 7
SCIE2060 Lab 3 Report Spring 2022
10. (4 marks) A ball rolls down a ramp for 23 s. If the ball’s initial velocity was 0.54 m/s and the
final velocity was 6.30 m/s, what was the acceleration of the ball?
11. (4 marks) If it takes a car 4.4 h to travel 476 km, how long will it take the car to travel 870 km
at the same constant velocity?
12. (4 marks) A tourist drops their phone from the top of a tall tower. If it takes 11.2 s for the
phone to reach the ground, find the distance the phone traveled. The acceleration is due to
gravity.
Page 5 of 7
SCIE2060 Lab 3 Report Spring 2022
13. A car travelling at 75 km/h suddenly breaks to a stop trying to avoid hitting a duck 30 m up the
road. Answer the following:
(a) (4 marks) If it took 3.7 s to stop, what is the acceleration (or deceleration — same thing)?
(b) (4 marks) Will the car stop in time, or will the car hit the duck?
Hint Make sure your units are the same for time.
The time for one run would not give an accurate representation of the car's speed or acceleration. The acceleration decreases as the distance increases because the force is spread out over a greater distance.
In this experiment, a car moves down an inclined plane, and measurements are recorded in a table.
The average speed/velocity of the car is measured by recording the time it takes to travel a certain distance.
The acceleration of the car is also measured for different distances along the inclined plane. The following are the answers to the discussion 1. The speed/velocity of the car increases from start to end. This is due to Newton’s first law of motion, which states that an object at rest will remain at rest, and an object in motion will remain in motion with a constant speed and direction unless acted upon by an unbalanced force. In this case, the force of gravity acts on the car, causing it to accelerate down the ramp.
2. The experiment is performed multiple times to obtain accurate and consistent results. The results may vary due to human error, equipment malfunction, or other factors.
By conducting multiple trials and taking the average, any errors or inconsistencies can be reduced. Recording the time for one run would not give an accurate representation of the car's speed or acceleration.
3a. Acceleration for Distance 1:Average speed = distance/time
Average speed = 40/0.50 = 80 m/s
Acceleration = change in speed/time = (80-0)/0.50 = 160 m/s^23b. Acceleration for Distance
2:Average speed = distance/time ,Average speed = 80/1.17 = 68.38 m/s
Acceleration = change in speed/time = (68.38-80)/1.17 = -10.24 m/s^2 (negative because the car is slowing down)3c. As the distance increases, the acceleration decreases.
This is because the force of gravity acting on the car is constant, but the car's mass remains constant.
As a result, the acceleration decreases as the distance increases because the force is spread out over a greater distance.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ11
An unstable high-energy particle enters a detector and leaves a track 1.15 mm long before it decays. Its speed relative to the detector was 0.956c. What is its proper lifetime in seconds? That is, how long would the particle have lasted before decay had it been at rest with respect to the detector? Number __________ Units _________
Proper Lifetime is the lifetime of a particle is the time for which it will exist before its decay if it were at rest. That is the time measured in the rest frame of the particle itself.
1. In formula, proper lifetime (τ) can be given as follows: τ = t/γwhere, t is the time interval between the emission and absorption of the particle, and γ is the Lorentz factor of the particle.
2. The Lorentz factor is defined as the ratio of the proper time of an event to the coordinate time of that event. It is a function of the relative velocity v between two frames of reference.γ = 1/√(1- v²/c²)where, c is the speed of light in vacuum.γ = 1/√(1- (0.956c)²/c²)γ = 1/√(1- 0.956²)γ = 1/√(0.044)γ = 1/0.2108γ = 4.739So, τ = t/γ⇒ t = τγ⇒ t = (1.15 × 10⁻³ m)/(0.956 × c) × γ = 4.739. Answer: 5.12 Units: × 10⁻¹³ s.
Learn more about proper lifetime:
https://brainly.com/question/13201150
#SPJ11
A piece of Nichrome wire has a radius of \( 6.8 \times 10^{-4} \mathrm{~m} \). It is used in a laboratory to make a heater that dissipates \( 3.30 \times 10^{2} \mathrm{~W} \) of power when connected
The necessary length of Nichrome wire is approximately 0.779 meters that can be obtained by calculating the resistance using the given power and voltage values.
To determine the necessary length of the Nichrome wire, we can use the formula for resistance, which is given by [tex]R = V^2 / P[/tex], where R represents resistance, V is the voltage, and P is the power dissipated. Rearranging the formula, we have [tex]R = V^2 / P = (130 V)^2 / (3.30 * 10^2 W)[/tex].
First, we need to calculate the resistance of the wire. Plugging in the values, we get [tex]R = (130 V)^2 / (3.30 * 10^2 W) = 514.14[/tex] Ω.
Next, we can use the formula for resistance of a wire, which is given by R = ρL / A, where ρ is the resistivity of Nichrome, L is the length of the wire, and A is the cross-sectional area. Rearranging the formula, we have L = R × A / ρ, where R is the resistance, A is the area (πr^2), and ρ is the resistivity of Nichrome[tex](1.10 * 10^-^6[/tex] Ω·m).
Substituting the known values, we have L = (514.14 Ω) [tex]× (\pi * (6.8 × 10^-^4 m)^2) / (1.10 * 10^-^6[/tex]Ω·m) ≈ 0.779 m. Therefore, the necessary length of wire is approximately 0.779 meters.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
The complete question is:
A piece of Nichrome wire has a radius of 6.8*10 ^−^4m. It is used in a laboratory to make a heater that dissipates 3.30*10^2 W of power when connected to a voltage source of 130 V. Ignoring the effect of temperature on resistance, estimate the necessary length of wire.
An evacuated tube uses an accelerating voltage of 1.900E1MegaVolts to accelerate protons to hit a copper plate. Non-relativistically, what would be the maximum speed of these protons? Enter your answer to 3 sigfigs in the coefficient and in calculator notation. Ex: 3.00E8. This problem required units
The maximum speed of the protons accelerated by a voltage of 1.900E1 MegaVolts is approximately 5.92E6 meters per second.
In non-relativistic conditions, the kinetic energy of a proton accelerated by a voltage can be calculated using the formula KE = qV, where KE is the kinetic energy, q is the charge of the proton (1.602E-19 Coulombs), and V is the accelerating voltage.
The maximum speed of the protons can be obtained by equating their kinetic energy to the energy gained from the accelerating voltage. The kinetic energy can be expressed as KE = (1/2)mv^2, where m is the mass of the proton (1.673E-27 kg) and v is its speed.
Setting the kinetic energy equal to the energy gained from the voltage, we have (1/2)mv^2 = qV. Rearranging the equation and solving for v, we find v = √(2qV/m).
Substituting the given values of q (1.602E-19 C), V (1.900E1 MegaVolts = 1.900E7 Volts), and m (1.673E-27 kg) into the equation, we can calculate the maximum speed of the protons. The resulting value is approximately 5.92E6 meters per second.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
An 8.70-kg block slides with an initial speed of 1.50 m/s down a ramp inclined at an angle of 28.6 with the horizontal. The coefficient of kinetic friction between the block and the ramp is. 0.74. Part A Use energy conservation to find the distance the block slides before coming to rest.
Using energy conservation, the block slides a distance of approximately 3.34 meters before coming to rest on the inclined ramp.
The initial energy of the block is in the form of kinetic energy, given by 1/2 * m * v^2, where m is the mass of the block (8.70 kg) and v is the initial speed (1.50 m/s). The gravitational potential energy of the block on the ramp is given by m * g * h, where g is the acceleration due to gravity (9.8 m/s^2) and h is the vertical height of the ramp. Since the block slides down the ramp, the change in height, h, is related to the distance traveled, d, and the angle of the ramp, θ, as h = d * sin(θ).
At the point where the block comes to rest, all of its initial kinetic energy is converted into work done against friction and an increase in potential energy due to the block's height on the ramp. The work done against friction is given by the product of the coefficient of kinetic friction (0.74), the normal force (m * g * cos(θ)), and the distance traveled, d.
Equating the initial kinetic energy to the work done against friction and the increase in potential energy, we have 1/2 * m * v^2 = 0.74 * (m * g * cos(θ) * d) + m * g * sin(θ) * d. Rearranging the equation and substituting the given values, we can solve for the distance traveled, d, which comes out to be approximately 3.34 meters. Therefore, the block slides a distance of about 3.34 meters before coming to rest on the inclined ramp.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Suppose you have a number of capacitors. Each is identical to the capacitor that is already in a series RCL circuit. How mary of these additional capacitors must be inserted in series in the circuit, so the resonant frequency increases by a factor of 8.0 ?
To increase the resonant frequency of a series RCL circuit by a factor of 8.0, additional capacitors need to be inserted in series. The number of capacitors required can be determined by considering the relationship between capacitance and resonant frequency.
In a series RCL circuit, the resonant frequency is given by the formula:
f = 1 / (2π√(LC))
where f is the resonant frequency, L is the inductance, and C is the capacitance.
To increase the resonant frequency by a factor of 8.0, we need to multiply the original frequency by 8.0. This means the new resonant frequency (f') is 8.0 times the original resonant frequency (f).
f' = 8.0f
Substituting the formula for resonant frequency, we can rewrite the equation as:
1 / (2π√(L(C+x)))
where x represents the additional capacitance to be inserted in series.
Squaring both sides of the equation and simplifying, we get:
64f^2 = 1 / (4π^2(L(C+x)))
Solving for x, we find:
x = (1 / (4π^2L)) - C
This equation gives the additional capacitance needed to increase the resonant frequency by a factor of 8.0. By knowing the value of the original capacitance, we can calculate the number of additional capacitors required to achieve this increase in resonant frequency.
Learn more about resonant frequency here:
https://brainly.com/question/32273580
#SPJ11