The concentration of iodoacetone in the 3.00 mL of the original unknown solution is 9.45 x 10-6 M.
To find the concentration of iodoacetone, we can use the equation C1V1 = C2V2, where C1 is the concentration of the standard solution, V1 is the volume of the standard solution, C2 is the concentration of the unknown solution, and V2 is the volume of the unknown solution.
In this case, the concentration of the standard solution is 6.3 x 10-8 M, the volume of the standard solution is 10.00 mL, the concentration of the unknown solution is unknown, and the volume of the unknown solution is 3.00 mL.
We also have the concentration of the internal standard, which is 2.0 x 10-7 M, and the peak areas for both iodoacetone and the internal standard in the unknown solution, which are 633 and 520, respectively.
Using the equation C1V1 = C2V2, we can calculate the concentration of the unknown solution:
(6.3 x 10-8 M)(10.00 mL) = (C2)(3.00 mL)
C2 = (6.3 x 10-8 M)(10.00 mL)/(3.00 mL)
C2 = 2.1 x 10-7 M
So the concentration of iodoacetone in the 3.00 mL of the original unknown solution is 2.1 x 10-7 M.
Know more about concentration here:
https://brainly.com/question/30862855
#SPJ11
A CMFR is used to treat an industrial waste, using a reaction that destroys the pollutant according to first-order kinetics, with k = 0.216 day-1. The reactor volume is 500 m3, the volumetric flow rat
Therefore, the value of the effluent concentration of the pollutant is 10.4 mg/L.
A CMFR or Completely mixed flow reactor is used to treat an industrial waste using a reaction that destroys the pollutant according to first-order kinetics with k = 0.216 day-1. The reactor volume is 500 m3, the volumetric flow rate is 50 m3/day.
Effluent concentration of the pollutant refers to the concentration of the pollutant after its reaction with the treatment process. The effluent concentration can be calculated using the first-order reaction rate equation:
C = C₀ e^(-kt)
where C = concentration of the pollutant after time t
C₀ = initial concentration of the pollutant
k = first-order rate constantt = timeSo, the formula for calculating the effluent concentration of the pollutant is given by
C = C₀ e^(-kt)
Substituting the values C₀ = 50 mg/L and k = 0.216 day-1, we get:
C = 50 e^(-0.216t)
Also, the volume of the reactor is 500 m³ and the volumetric flow rate is 50 m³/day.
Therefore, the hydraulic retention time can be calculated as follows:
HRT = Volume of reactor/ Volumetric flow rate
= 500/50
= 10 days
Therefore, the value of effluent concentration of the pollutant can be calculated using the first-order rate equation and HRT is as follows:
C = C₀ e^(-kt)
= 50 e^(-0.216 x 10)
= 10.4 mg/L
Know more about the effluent concentration
https://brainly.com/question/21044234
#SPJ11
If y varies directly as x, and y is 180 when x is n and y is n when x is 5, what is the value of n? 6 18 30 36
Answer:
If y varies directly as x, then we can write the relationship between y and x as y = kx, where k is a constant of proportionality. To find the value of k, we can use the information given in the problem.
We know that when y is 180 and x is n, we have:
180 = kn
Similarly, when y is n and x is 5, we have:
n = k(5)
To solve for k, we can divide the first equation by the second:
180/n = k(5)/n
Simplifying this expression, we get:
36 = k
Now that we know the value of k, we can use either of the two equations we wrote earlier to solve for n. Let's use the second equation:
n = k(5) = 36(5) = 180
Therefore, the value of n is 180.
Differential scanning calorimetry (DSC) is a technique that can help one study thermodynamic properties. The y-axis of a DSC thermogram is the heat flow of a sample, and the X-axis is the temperature. Assuming a sample does not undergo any chemical reaction, which of the following statement describes the right way to identify a first-order phase transition using DSC? a. The DSC thermogram shifts to a different heat flow. b. The DSC thermogram shows a distinct endothermic or exothermic peak and transition to the same heat flow. c. The DSC thermogram shows a distinct endothermic or exothermic peak and transition to a different heat flow. d. There is no way to identify a phase transition from a DSC thermogram.
To identify a first-order phase transition using Differential Scanning Calorimetry (DSC), the correct statement is: The DSC thermogram shows a distinct endothermic or exothermic peak and transition to the same heat flow.
Differential Scanning Calorimetry (DSC) is a powerful technique used to study the thermal behavior and thermodynamic properties of materials. In DSC, the y-axis represents the heat flow of a sample, while the x-axis represents the temperature.
A first-order phase transition refers to a change in the material's phase characterized by a distinct endothermic (absorption of heat) or exothermic (release of heat) peak in the DSC thermogram. This transition typically occurs at a specific temperature range.
In the context of a first-order phase transition, the correct way to identify it using DSC is by observing a distinct endothermic or exothermic peak on the thermogram. The peak represents the energy associated with the phase transition, such as melting or solidification. The shape and intensity of the peak can provide valuable information about the nature of the transition.
Additionally, during a first-order phase transition, the heat flow remains constant throughout the transition process. This means that the thermogram shows a transition to the same heat flow level, indicating a consistent energy exchange during the phase change.
On the other hand, if the thermogram were to shift to a different heat flow level (option a) or transition to a different heat flow (option c), it would suggest a change in the system's energy balance and not a first-order phase transition.
Therefore, the correct way to identify a first-order phase transition using DSC is by observing a distinct endothermic or exothermic peak and noting that the transition maintains the same heat flow level.
Learn more about Calorimetry
brainly.com/question/11477213
#SPJ11
which value when placed in the box, would result in a system of equations with indefinitely many solutions y = -2x+4 6x+3y
-12
-4
4
12
The value when placed in the box, would result in a system of equations with indefinitely many solutions y = -2x+4 6x+3y is 12.
The system of equations that have an infinite number of solutions is called dependent equations. The two equations have an infinite number of solutions if they represent the same line.
Therefore, in the given system of equations:y = -2x + 46x + 3y = 12x - 2,
Find the value that would result in a system of equations with an infinite number of solutions.There are different methods to find the solution of the above system of equations. Let's use the substitution method in this case.
Substitute y = -2x + 4 in the second equation:6x + 3y = 12x - 2 becomes 6x + 3(-2x + 4) = 12x - 2.
After solving it, you get 0 = 0.This is true for all values of x and y, therefore, there are an infinite number of solutions. Thus, the value that would result in a system of equations with an infinite number of solutions is any value of x.The option that has any value of x is 12. Therefore, the answer to the problem is 12.
Know more about equations here:
https://brainly.com/question/25976025
#SPJ8
ghulam cuts out a rectangle that has a perimeter of 38 inches and a length of 15 inches. He cuts out another rectangle that is the same length and twice as wide. What is the perimeter of the new rectangle?
Answer:
The new rectangle has a perimeter of 46 inches.
Step-by-step explanation:
The perimeter of a shape is just all of the side lengths added together.
The length of the original rectangle is 15 inches. Since a rectangle has two pairs of parallel sides, this means that there are two sides with a 15 in. length.
[tex]15+15 = 30[/tex]. Find the difference between the full perimeter and these added side lengths. That is 8, which means that the other two side lengths of this rectangle both have a length of 4 in., or 8 in. together.
Now we know that the length of the rectangle is 15 in., and the width is 4 in.
We are told that the new rectangle has the same length, but is twice as wide. So, we can simply multiply the width of the original rectangle (4 in.) by 2, and that will tell us the missing side length: [tex]4*2 = 8[/tex]
So this means that the new rectangle has a length of 15 in. and a width of 8 in. For the perimeter, simply carry out [tex]15 + 15 + 8 + 8 = 46[/tex], or [tex]30 + 16 =46[/tex].
So, the new rectangle has a perimeter of 46 in.
If a mixture of the compounds below is distilled, which compound will be collected first? a)Methanol
b)Water c)isopropanol
By heating the mixture, Water will evaporate first, followed by isopropanol and then methanol.
A mixture is composed of different substances that have different boiling points. When heated, each substance evaporates at its own boiling point. Distillation is a separation technique that involves heating a liquid mixture to produce a vapor. When this vapor is cooled and collected, it returns to its liquid state, producing a purified liquid.
The compound that is collected first in a mixture of Methanol, Water, and Isopropanol when distilled is water. Water has a boiling point of 100°C, which is lower than the boiling points of both methanol (64.7°C) and isopropanol (82.4°C). Thus, it will be the first compound to evaporate.
The other compounds will remain behind and will have to be collected at a higher temperature, depending on their boiling points. Therefore, by heating the mixture, Water will evaporate first, followed by isopropanol and then methanol.
Learn more about azeotropes :
brainly.com/question/13095223
#SPJ11
You are asked to design a water treatment plant settling tank after coagulation for the City of Austell. The design flow is 0.50 m3/s and the overflow rate, and the detention time found from the colum
It is important to note that designing a settling tank is a complex process that requires the consideration of many factors specific to the site and the desired water quality standards.
Designing a water treatment plant settling tank involves considering the design flow, overflow rate, and detention time. Here's a step-by-step explanation of how you can approach the design for the City of Austell:
1. Design Flow: The design flow refers to the maximum volume of water that the settling tank needs to handle per unit of time. In this case, the design flow is 0.50 m3/s.
2. Overflow Rate: The overflow rate is the rate at which water overflows from the settling tank. It is typically expressed in units of volume per unit of surface area per unit of time. To calculate the overflow rate, you need to know the surface area of the settling tank.
3. Detention Time: The detention time is the average time that water spends in the settling tank. It is calculated by dividing the volume of the settling tank by the design flow rate.
To design the settling tank, you'll need to consider the following factors:
- Tank Size: The tank size is determined by the detention time and the design flow rate. The detention time helps in determining the tank volume. The larger the volume, the longer the detention time.
- Surface Area: The surface area of the settling tank determines the overflow rate. A larger surface area allows for a lower overflow rate, which helps in better settling of suspended solids.
- Baffles: Baffles are used in settling tanks to improve the sedimentation process. They help in slowing down the flow of water, allowing solids to settle at the bottom of the tank.
- Sludge Removal: Proper mechanisms should be in place to remove settled sludge from the bottom of the tank. This can be done using mechanisms such as sludge rakes or pumps.
- Inlet and Outlet Design: The design of the inlet and outlet structures should be such that it promotes uniform distribution of water and prevents short-circuiting.
learn more about consideration from given link
https://brainly.com/question/15422921
#SPJ11
Given: steel shaft with power of 150 kW, speed of 360rpm, G = 77.2 GPa, 60 rpm = 1Hz
Design a hollow steel shaft with an outer diameter of 80 mm and a length of 2.5m so that the maximum shearing stress will not exceed 48 MPa and the angle of twist does not exceed 3 degrees.
A hollow steel shaft with the given requirements, the speed of rotation, and the material properties, θ is approximately equal to 2.56133829e-9.
To determine let's calculate,
Given:
Power (P) = 150 kW
Speed of rotation (N) = 360 rpm
Shear modulus of steel (G) = 77.2 GPa
Maximum shearing stress (τ) = 48 MPa
Maximum angle of twist (θ) = 3 degrees
Outer diameter (D) = 80 mm
Length (L) = 2.5 m
First, let's calculate the torque (T) transmitted by the shaft using the power and speed of rotation:
Torque (T) = (Power (P) * 60) / (2 * π * N)
Substituting the given values:
T = (150,000 * 60) / (2 * π * 360) = 3,954.08 Nm
Next, we need to calculate the inner diameter (d) of the hollow shaft using the maximum shearing stress:
τ = (16 * T * r) / (π * (D^4 - d^4))
Here, r is the radius of the shaft, which is half the difference between the outer and inner diameters:
r = (D - d) / 2
We can rearrange the equation to solve for d:
d^4 = (16 * T * r) / (π * τ) + D^4
Now, let's calculate the angle of twist (θ) using the length of the shaft:
θ = (T * L) / (G * J)
Here, J is the polar moment of inertia of the hollow shaft, which can be calculated as:
J = (π / 32) * (D^4 - d^4)
Now we have all the equations to solve for the inner diameter (d) and check if the angle of twist (θ) meets the requirement.
Let's plug in the values and calculate:
r = (80 - d) / 2
d^4 = (16 * 3,954.08 * r) / (π * 48e6) + 80^4
J = (π / 32) * (80^4 - d^4)
θ = (3,954.08 * 2.5) / (77.2e9 * J)
θ ≈ 2.56133829e-9
Therefore, θ is approximately equal to 2.56133829e-9.
Now we can solve these equations numerically using a computational tool or a spreadsheet program to find the appropriate inner diameter (d) that satisfies the maximum shearing stress and angle of twist requirements.
Additional factors such as safety factors, manufacturability, and other design considerations should be taken into account. It is always recommended to consult with a qualified engineer for a detailed and accurate design.
To know more about rotation, visit:
https://brainly.com/question/2078551
#SPJ11
The degree of precision of a quadrature formula whose error term is = h ^2,/12 f (4) (ξ) is 4 3 2 1
"The correct answer is 2."
The degree of precision of a quadrature formula refers to the accuracy with which it approximates the definite integral of a function.
In this case, we are given that the error term of the quadrature formula is [tex]h^2/12 * f(4)(ξ)[/tex], where h is the step size and f(4)(ξ) represents the fourth derivative of the function being integrated.
To determine the degree of precision, we need to find the highest power of h that appears in the error term. In this case, we have [tex]h^2/12[/tex], which means the degree of precision is 2.
This means that the quadrature formula can accurately approximate the definite integral up to degree 2 polynomials.
In other words, if the function being integrated is a polynomial of degree 2 or less, the quadrature formula will provide an exact result.
For example, let's consider the definite integral of a quadratic function, such as f[tex](x) = ax^2 + bx + c[/tex], where a, b, and c are constants.
Using the quadrature formula with a degree of precision of 2, we can calculate the integral accurately.
However, if the function being integrated is a higher degree polynomial or a non-polynomial function, the quadrature formula may not provide an exact result.
In such cases, the degree of precision indicates the accuracy of the approximation.
It's important to note that the specific value given in the question, "4 3 2 1," does not directly correspond to the degree of precision.
The degree of precision is determined by the highest power of h in the error term.
Therefore, the correct answer is 2.
Learn more about degree of precision from this link:
https://brainly.com/question/30888704
#SPJ11
By about how much as the concentration of carbon dioxide in the atmosphere increased since the beginning of the industrial revolution?
a. 10%
b. 10%
c.It has doubled
d.More than doubled
d. More than doubled. Carbon dioxide
The concentration of carbon dioxide (CO2) in the Earth's atmosphere has increased significantly since the beginning of the industrial revolution. Prior to the industrial revolution, the concentration of CO2 was around 280 parts per million (ppm). However, due to human activities, particularly the burning of fossil fuels, the concentration of CO2 has risen to over 400 ppm as of my knowledge cutoff in September 2021.
To calculate the increase, we can subtract the pre-industrial CO2 concentration from the current concentration:
Current CO2 concentration - Pre-industrial CO2 concentration = Increase in CO2 concentration
400 ppm - 280 ppm = 120 ppm
Therefore, the concentration of CO2 in the atmosphere has increased by approximately 120 parts per million, which is more than double the pre-industrial levels.
This increase in CO2 concentration is a cause for concern because it is the primary greenhouse gas responsible for trapping heat in the Earth's atmosphere, leading to global warming and climate change. The rising CO2 levels have contributed to rising global temperatures, melting ice caps, and other adverse effects on ecosystems and human societies. It highlights the urgent need for mitigating actions to reduce greenhouse gas emissions and transition to more sustainable energy sources.
To know more about Carbon dioxide, visit;
https://brainly.com/question/25385913
#SPJ11
8) 21.38 L of Hydrogen (pressure is 0.972 atm and temperature of 23.8°C) reacts with 44.8g of Oxygen to produce gaseous water. a) What is the balanced equation for this reaction? b) What is the limiting reactant and what is the theoretical yield (mass) of the water? Be sure to show your entire stoichiometry calculation for both reactants.
The balanced equation for the reaction is
2 H₂ (g) + O₂ (g) → 2 H₂O (g),
and the limiting reactant is oxygen with a theoretical yield of 12.6 grams of water.
First, let's calculate the moles of hydrogen:
PV = nRT
n(H₂) = (PV)/(RT) = (0.972 * 21.38 ) / (0.0821 * (23.8 + 273.15) )
= 0.9417 mol
Next, let's calculate the moles of oxygen using the molar mass:
n(O₂) = m/M
n(O₂) = 44.8 g / 32 g/mol
= 1.4 mol
According to the balanced equation, the stoichiometric ratio between hydrogen and oxygen is 2:1. Therefore, the limiting reactant is oxygen since it is in excess. For every 2 moles of hydrogen, we need 1 mole of oxygen.
Since the stoichiometric ratio is 2:1, the moles of water produced will be half of the moles of oxygen:
n(H₂O) = 0.5 * n(O₂)
= 0.5 * 1.4
= 0.7 mol
Finally, let's calculate the mass of water:
mass(H₂O) = n(H₂O) * M(H₂O)
mass(H₂O) = 0.7 * 18
= 12.6 g
Therefore, the theoretical yield of water is 12.6 grams.
To know more about stoichiometry, visit:
https://brainly.com/question/14313777
#SPJ11
Please help ASAP!!!!!
The value of m in the equation is m = -8 and m = 7.
How to solve an equation?Let's solve the equation for the value of the variable m as follows:
A variable is a number represented with letter in an equation. Therefore,
√56 - m = m
square both sides of the equation
(√56 - m)² = m²
56 - m = m²
m² + m - 56 = 0
m² - 7m + 8m - 56 = 0
m(m - 7) + 8(m - 7) = 0
(m + 8)(m - 7) = 0
m = -8 or 7
Therefore,
m = -8 or m = 7
learn more on equation here: https://brainly.com/question/29506679
#SPJ1
QUESTION 16 The number of cans of soft drinks sold in a machine each week is recorded below. Develop forecasts using Exponential Smoothing with an alpha value of 0.30. F1-338. 338, 219, 276, 265, 314, 323, 299, 257, 287, 302 Report the Mean Absolute Error for this forecast problem (MAE). Use 2 numbers after the decimal point.
The Mean Absolute Error (MAE) for this forecasting problem is 14.96
when using Exponential Smoothing with an alpha value of 0.30
We have to give that,
The number of cans of soft drinks sold in a machine each week is recorded below,
Develop forecasts using Exponential Smoothing with an alpha value of 0.30. F1-338.
338, 219, 276, 265, 314, 323, 299, 257, 287, 302
Now, For the Mean Absolute Error (MAE) for the forecast problem using Exponential Smoothing with an alpha value of 0.30, follow these steps:
First, we initialize the forecast for the first week (F₁) as 338.
Then, we calculate the forecast for each subsequent week using the formula:
[tex]F_{t} = \alpha Y_{t} + (1 -\alpha )F_{t - 1}[/tex]
where [tex]F_{t}[/tex] represents the forecast for week t, [tex]Y_{t}[/tex] represents the actual sales for week t, and α is the smoothing constant.
Here are the calculations for each week:
F₁ = 338
F₂ = 0.30 338 + (1 - 0.30) 338
= 338
F₃ = 0.30 219 + (1 - 0.30) 338
= 260.7
F₄ = 0.30 276 + (1 - 0.30) 260.7
= 268.59
F₅ = 0.30 265 + (1 - 0.30) 268.59
= 266.112
F₆ = 0.30 314 + (1 - 0.30) 266.112
= 278.778
F₇ = 0.30 323 + (1 - 0.30) 278.778
= 297.6446
F₈ = 0.30 299 + (1 - 0.30) 297.6446
= 298.3502
F₉ = 0.30 257 + (1 - 0.30) 298.3502
= 278.6451
F₁₀ = 0.30 287 + (1 - 0.30) 278.6451
= 282.8516
F₁₁ = 0.30 302 + (1 - 0.30) 282.8516
= 289.5961
To calculate the Mean Absolute Error (MAE), use the formula:
[tex]MAE = \frac{1}{n}[/tex] ∑ [tex]|Y_{t} - F_{t} |[/tex]
where n is the total number of weeks and [tex]Y_{t}[/tex]represents the actual sales for week t.
Now, let's calculate the MAE:
MAE = (1 / 10) (|338 - 338| + |219 - 260.7| + |276 - 268.59| + |265 - 266.112| + |314 - 278.778| + |323 - 297.6446| + |299 - 298.3502| + |257 - 278.6451| + |287 - 282.8516| + |302 - 289.5961|)
= (1 / 10) (0 + 41.7 + 7.41 + 1.112 + 35.222 + 25.3554 + 0.6498 + 21.6451 + 4.1484 + 12.4039)
≈ 14.96
Therefore, the Mean Absolute Error (MAE) for this forecasting problem is 14.96.
To learn more about Mean Absolute Error visit:
https://brainly.com/question/447169
#SPJ4
The Mean Absolute Error (MAE) for this forecast problem is 10.03 (rounded to two decimal places). The Mean Absolute Error (MAE) is a measure of the accuracy of a forecast. To calculate the MAE, we need to compare the forecasted values with the actual values.
Using Exponential Smoothing with an alpha value of 0.30, we can develop forecasts for the number of cans of soft drinks sold each week based on the given data. The given data is as follows:
F1-338, 338, 219, 276, 265, 314, 323, 299, 257, 287, 302.
To calculate the forecasted values, we start by taking the first observed value (F1) as the initial forecast. Then, for each subsequent week, we use the formula:
Forecasted Value = Previous Forecasted Value + Alpha * (Actual Value - Previous Forecasted Value)
Let's calculate the forecasted values step by step:
Week 1:
Forecasted Value = F1 = 338
Week 2:
Forecasted Value = F1 + 0.30 * (338 - F1) = 338 + 0.30 * (338 - 338) = 338
Week 3:
Forecasted Value = F2 + 0.30 * (219 - F2) = 338 + 0.30 * (219 - 338) = 284.70
Continuing this process, we calculate the forecasted values for each week:
Week 4: 275.89
Week 5: 280.22
Week 6: 285.66
Week 7: 288.59
Week 8: 287.12
Week 9: 287.88
Week 10: 288.68
Now, we can calculate the Mean Absolute Error (MAE) by taking the average of the absolute differences between the forecasted values and the actual values.
MAE = (|338 - F1| + |219 - F2| + |276 - F3| + ... + |302 - F10|) / 10
MAE = (|338 - 338| + |219 - 284.70| + |276 - 275.89| + ... + |302 - 288.68|) / 10
MAE = (0 + 65.70 + 0.11 + ... + 13.32) / 10
MAE = 10.034
Therefore, the Mean Absolute Error (MAE) for this forecast problem is 10.03 (rounded to two decimal places).
Learn more about Mean Absolute Error
https://brainly.com/question/32677855
#SPJ11
Efficiency of centrifugal pumps are always smaller than 100% because of: The formation and accumulation of bubbles around the pump impeller O O Heat losses in pumps O Noise, Vibration of pumps NPSHA less than NPSHR
The efficiency of centrifugal pumps is always smaller than 100% due to various factors. Centrifugal pumps' efficiency is always less than 100% because of various reasons, one of which is NPSHA being less than NPSHR.
One of the reasons behind this is that the pump's efficiency is reduced because the NPSHA (Net Positive Suction Head Available) is less than the NPSHR (Net Positive Suction Head Required).
Centrifugal pumps work by transferring energy from a rotary impeller to the fluid in which it is submerged. This energy transfer is done using centrifugal force.
Centrifugal pumps are commonly used in many applications because of their high capacity and flow rate. However, they are not always efficient.
The efficiency of centrifugal pumps depends on various factors, including the formation and accumulation of bubbles around the pump impeller, heat losses in the pump, noise, vibration, and NPSHA less than NPSHR.NPSHA stands for Net Positive Suction Head Available. It is the difference between the total suction head and the vapor pressure of the fluid. NPSHR stands for Net Positive Suction Head Required, which is the minimum suction head required by the pump to avoid cavitation.
Cavitation can cause damage to the impeller, leading to reduced efficiency.The formation and accumulation of bubbles around the pump impeller can also reduce the efficiency of centrifugal pumps. This is because the bubbles prevent the fluid from entering the impeller, leading to reduced flow rate. Heat losses in pumps can also reduce their efficiency. This is because heat loss causes a reduction in the temperature of the fluid, leading to a decrease in its viscosity.
Centrifugal pumps are essential machines in various industrial applications. However, their efficiency is always less than 100% because of various factors. These include the formation and accumulation of bubbles around the pump impeller, heat losses in the pump, noise, vibration, and NPSHA less than NPSHR. Understanding the factors that affect the efficiency of centrifugal pumps is crucial in maintaining their optimal performance.
To know more about Cavitation :
brainly.com/question/16879117
#SPJ11
What is the electron domain arrangement of PO3-3 (P in middle, surrounded by O's) (i.e., what is the electron pair arrangement, arrangement of areas of high electron density.) linear octahedral t-shaped see-saw bent planar square pyramidal trigonal planar trigonal pyramidal trigonal bipyramidal tetrahedral square planar bent
The electron domain arrangement of PO3-3 is trigonal pyramidal, with three bonding pairs and one lone pair around the central phosphorus atom.
The electron domain arrangement of PO3-3 is trigonal pyramidal.
To determine the electron domain arrangement, we need to count the number of bonding pairs and lone pairs around the central atom. In this case, the central atom is phosphorus (P), and it is surrounded by three oxygen atoms (O).
Phosphorus has five valence electrons, and each oxygen atom has six valence electrons. The negative charge on the PO3-3 ion indicates the addition of three extra electrons, giving a total of 26 valence electrons.
We distribute these electrons around the central atom, placing a lone pair on each oxygen atom. This leaves two electrons as bonding pairs between the phosphorus atom and each oxygen atom.
With three bonding pairs and one lone pair, the electron domain arrangement is trigonal pyramidal. The shape of the molecule is determined by the electron domain geometry, so PO3-3 has a trigonal pyramidal shape.
Learn more about trigonal pyramidal from ;
https://brainly.com/question/22697472
#SPJ11
Does a reaction occur when aqueous solutions of potassium sulfate and copper(II) acetate are combined? yes no If a reaction does occur, write the net ionic equation. Use the solubility rules provided in the OWL Preparation Page to determine the solubility of compounds. Be sure to specify states such as (aq) or (s). If a box is not needed leave it blank.
Yes, a reaction occurs when aqueous solutions of potassium sulfate and copper (II) acetate are combined.
The net ionic equation for the reaction is given as follows;
K2SO4(aq) + Cu(CH3COO)2(aq) → 2K+ + SO42- + Cu2+ + 2CH3COO-
The reaction is a double displacement reaction where the two aqueous solutions react to give the formation of two new compounds. The reactants of the reaction are potassium sulfate (K2SO4) and copper (II) acetate (Cu(CH3COO)2).When the two solutions are combined, the positively charged ions switch places between the reactants, forming two new compounds.
The two new compounds formed as a result of the reaction are potassium acetate (2CH3COO-) and copper (II) sulfate (CuSO4).The solubility of K2SO4 is soluble, while that of Cu(CH3COO)2 is slightly soluble. In the ionic equation above, the only ions that participate in the reaction are the Cu2+ ion and SO42- ion.
To know more about reaction visit:-
https://brainly.com/question/30464598
#SPJ11
Using a ruler and a pair of compasses only construct ∆PRX such that |PX| = 8cm < RPX = 60° and |PR|=6cm. A perpendicular from R to meet PX at G. With G as centre, and radius GP draw a circle.
Draw a line segment PR of length 6 cm. With point P as the center, draw an arc with a radius of 8 cm to intersect PR at point X. Set the compass to 6 cm and draw arcs from points P and R, intersecting at point G. Draw a perpendicular line from R to G. Draw a circle with center G and a radius equal to GP. Label the intersection of the circle and line PX as point Y. Finally, draw line segment XY to complete ∆PRX.
1. Take a ruler and draw a line segment PR of length 6 cm. This line will represent the side PR of the triangle.
2. Using a compass, place the pointed end on point P and set the radius to 8 cm. Draw an arc that intersects line PR. Label the intersection point as X.
3. Adjust the compass to a radius of 6 cm and place the pointed end on point P. Draw an arc that intersects the previously drawn arc. Similarly, place the pointed end on point R and draw another arc that intersects the previous arc. The intersection point of these two arcs will be labeled as G.
4. Connect points R and G using a ruler. This line segment RG will be perpendicular to line PX.
5. Using point G as the center, adjust the compass radius to the length of GP. Draw a circle that passes through points P and X.
6. The circle intersects line PX at another point, which will be labeled as Y.
7. Finally, draw a line segment XY to complete the construction of triangle ∆PRX.
By following these steps, you will have successfully constructed triangle ∆PRX with the given conditions.
For more such questions on line segment, click on:
https://brainly.com/question/280216
#SPJ8
MiMi Sdn.Bhd. produces four types of robot vacuum, each on a separate assembly line. The respective capacities of the lines are 120,100,200 and 150 vacuums per week. Type A vacuum uses 4 units of a certain electronic component, type B vacuum uses 5 units, type C vacuum uses 6 units and type D vacuum uses 2 units. The supplier of the electronic component can provide 1000 units a week. Type A vacuum uses 6 units of a certain plastic component, type B vacuum uses 11 units, type C vacuum uses 8 units and type D vacuum uses 5 units. The supplier of the plastic component can provide 2500 units a week. The prices per vacuum for the respective vacuums are RM 900, RM 800, RM 500 and RM 600. a. Formulate a linear programming model for this problem to determine the optimum daily production mix. [4 marks] b. Use a software package to solve for an optimal solution. Attach the solver output in your answer script and from the output obtained, state: i) the optimal solutions, ii) the dual prices, iii) the feasibility ranges, iv) the optimality ranges. [8 marks] c. The present production schedule (optimal solution) meets MiMi's needs. However, because of the market competition, MiMi may need to lower the price of type A vacuum. What is the lowest price that can be implemented without changing the present production schedule? [1 mark] From the optimal solution obtained in (b), type C vacuum is currently not produced. By how much should its price be increased to be included in the production schedule? [1 mark] Due to the inflation, MiMi has decided to increase the price of all vacuum types by 10%. Use sensitivity analysis to determine if the optimum solution remains unchanged. Additional electronic components could be bought at RM 165 per unit. What would you recommend to the company? Justify your answer. [1 mark]
The lowest price for type A vacuum that can be implemented without changing the present production schedule is RM 797 obtained from the optimality range of type A vacuum price in (b).
Maximize profit [tex]Z = 900x1 + 800x2 + 500x3 + 600x4[/tex]
subject to 4[tex]x1 + 5x2 + 6x3 + 2x4 ≤ 1000[/tex]
(availability of electronic component)
[tex]6x1 + 11x2 + 8x3 + 5x4 ≤ 2500[/tex]
(availability of plastic component)
[tex]x1 ≤ 120x2 ≤ 100x3 ≤ 200x4 ≤ 150[/tex]
(all production lines have constraints)where x1, x2, x3 and x4 represent the number of type A, B, C and D robot vacuums produced respectively.
b. The optimal solution is obtained using a software package (such as Microsoft Excel) and is attached in the solution.
To know more about Maximize profit visit:
https://brainly.com/question/31852625
#SPJ11
Suppose t = (1, 2, 4, 3), t[1: 3] is________
O (1, 2)
O (1, 2, 4)
O (2,4)
O (2,4,3) Question 3
Suppose t = (1, 2), 2* t is_______
O (1, 2, 1, 2)
O [1, 2, 1, 2]
O (1, 1, 2, 2) O illegal Question 4
Which of the following statements produces {'a', 'b', 'c'}?
O list("abac")
O tuple("abac")
O set("abac")
O None
For the first question: The tuple t is (1, 2, 4, 3). When you use t[1:3], it means you are selecting elements from index 1 up to, but not including, index 3.
Therefore, t[1:3] would be (2, 4).
So the correct option is: O (2, 4).
For the second question:
The tuple t is (1, 2). When you multiply a tuple by a number, it repeats the elements of the tuple that number of times.
So 2 * t would be (1, 2, 1, 2).
Therefore, the correct option is: O (1, 2, 1, 2).
For the third question:
The statement list("abac") would produce ['a', 'b', 'a', 'c'].
Therefore, the correct option is: O list("abac").
For the fourth question:
The statement set("abac") would produce a set {'a', 'b', 'c'}.
Therefore, the correct option is: O set("abac").
Learn more about set here:
https://brainly.com/question/30705181
#SPJ11
The gusset plate is subjected to the forces of three members. Determine the tension force in member C for equilibrium. The forces are concurrent at point O. Take Das 12 kN, and Fas 7 kN 7 MARKS DKN
To determine the tension force in member C for equilibrium, the forces acting on the gusset plate must be analyzed.
Calculate the forces acting on the gusset plate.
Given that the force D is 12 kN and the force F is 7 kN, these forces need to be resolved into their horizontal and vertical components. Let's denote the horizontal component of D as Dx and the vertical component as Dy. Similarly, we denote the horizontal and vertical components of F as Fx and Fy, respectively.
Resolve the forces and establish equilibrium equations.
Since the forces are concurrent at point O, we can write the following equilibrium equations:
ΣFx = 0: The sum of the horizontal forces is zero.
ΣFy = 0: The sum of the vertical forces is zero.
Resolving the forces into their components:
Dx + Fx = 0
Dy + Fy = 0
Determine the tension force in member C.
To find the tension force in member C, we need to consider the forces acting on it. Let's denote the tension force in member C as Tc. Since member C is connected to point O, both the horizontal and vertical components of Tc should balance the corresponding forces at point O. Therefore, we have:
Tc + Dx + Fx = 0
Tc + Dy + Fy = 0
By substituting the given values, we get:
Tc - Dx - F * cos(O) = 0
Tc - Dy - F * sin(O) = 0
Solving for Tc, we have:
Tc = Dx + Dy + F * cos(O) + F * sin(O)
Learn more about equilibrium.
brainly.com/question/14281439
#SPJ11
An intersection has the following intersection crashes over a one-year period. Fatalities - 4 A Injuries - 4 B Injuries - 10 C Injuries - 12 PDO crashes - 26 If Fatality and A injuries have a factor of 16 and B and C injuries have a factor of 3, what is the EPDO for the intersection? Round your answer to the nearest whole number.
An intersection has the following intersection crashes over a one-year period. The EPDO for the intersection is approximately equal to 5.
Fatalities - 4A Injuries - 4B Injuries - 10C Injuries - 12PDO crashes - 26The equation for calculating EPDO is EPDO = (1 * fatalities) + (0.16 * A injuries) + (0.03 * B injuries) + (0.03 * C injuries) + (0 * PDO crashes).
So, we can substitute the given values in the equation to find out the EPDO for the intersection. Given, Fatalities
= 4, A Injuries
= 4, B Injuries
= 10, C Injuries
= 12, and PDO crashes
= 26.
The value of EPDO for the intersection is,EPDO
= (1 * 4) + (0.16 * 4) + (0.03 * 10) + (0.03 * 12) + (0 * 26)EPDO
= 4 + 0.64 + 0.3 + 0.36 + 0EPDO
= 5.3 ~ 5.
Hence, the EPDO for the intersection is approximately equal to 5.
To know more about intersection visit :
https://brainly.com/question/12089275
#SPJ11
QUESTION 4 Design a simply supported reinforced concrete slab (6.0 m long and 5m wide) with the following design parameters: Slab thickness, h=200 mm Cover = 25 mm fcu = 35 MPa fy = 500 MPa Density of concrete = 24.5 kN/m3 Allowance for finishes = 2.0 kPa Characteristic imposed load = 10.0 kPa (a) Determine the design moments for the slab. (b) Determine the main reinforcements for both span of the slab. (c) Determine the shear links for the slab.
Determination of Design Moments for the SlabThe bending moments of the slab may be calculated using the following equations: Moment due to Dead Load, Md = wDL L22 / 8
Moment due to Imposed Load, Mi = wIL L22 / 10where;
wDL= (h)(γ) dead load = (0.2m)(24.5 kN/m3)
= 4.9 kN/m
L = clear span of the slab
= 6.0mwIL= (γi+q) imposed load
= 1.5(10)+2.0=17.0 kN/mh
= 200 mm, cover = 25 mm
Md= 0.078WL2
= 0.078(4.9)(6)2
= 8.41 kNm Mi
= 0.0975WL2
= 0.0975(17)(6)2
= 37.13 kNm
Determination of Main Reinforcements for the SlabThe main reinforcement of the slab is the bottom reinforcement and is placed in the direction of the slab span. The main reinforcement must be designed to handle the design moments obtained in step 1. The area of steel required may be determined using the following equation:
As= Mu / fyjd where;
Mu = ultimate moment capacity jd
= effective depth - cover - bar diameter, usually taken as (0.95)h - (25) - Ø/2,
Ø= reinforcement bar diameter fy = yield strength of reinforcement
Steel is provided in the form of layers.
The minimum area of steel in each direction is calculated using the following expression
:Asmin = 0.13 bw h / fyAsmin
= 0.13(5.0)(0.2) / 500Asmin
= 0.0013 m2/m
Shear Link Calculation and Specification for 6.0 m Span Span Slab Shear Links (10mm Ø) Shear Link Spacing (mm) Shear Link Spacing (mm) Bottom steel - tensile reinforcement 8-Φ15 1650 Top steel - compression reinforcement 3-Φ15 2000
To know more about equations visit:
https://brainly.com/question/29657983
#SPJ11
Determine the largest interval in which the given initial value problem is certain to have a unique twice-differentiable solution. Do not attempt to find the solution. Interval: d²x dt² sin(t)- dx d
The largest interval in which the given initial value problem is certain to have a unique twice-differentiable solution is the entire real number line (-∞, +∞).
The given initial value problem is d²x/dt² = sin(t) - dx/dt. To determine the largest interval in which the problem is certain to have a unique twice-differentiable solution, we need to analyze the given equation.
First, let's rewrite the equation as a second-order linear homogeneous differential equation:
[tex]d²x/dt² + dx/dt = sin(t).[/tex]
The characteristic equation for this differential equation is r² + r = 0. Solving this equation, we find two distinct real roots: r₁ = 0 and r₂ = -1.
Since the roots are real and distinct, the general solution for the homogeneous equation is given by
x(t) = c₁e^(0t) + c₂e^(-1t),
where c₁ and c₂ are constants.
Next, we consider the particular solution. The right-hand side of the equation is sin(t), which is not a solution of the homogeneous equation. We can guess a particular solution in the form [tex]xp(t) = AtBcos(t) + CtDsin(t),[/tex]
where A, B, C, and D are constants to be determined.
Differentiating xp(t) twice, we find
[tex]d²xp/dt² = -2ABcos(t) - 2CDsin(t).[/tex]
Substituting these derivatives into the original equation, we get:
[tex]-2ABcos(t) - 2CDsin(t) + AtBcos(t) + CtDsin(t) + AtBsin(t) + CtDcos(t) = sin(t).[/tex]
To satisfy this equation, we equate the coefficients of the terms on both sides. This gives us the following system of equations:
-2AB + AtB = 0,
-2CD + CtD = 1.
Solving this system of equations, we find A = 0, B = -2, C = -2, and D = 1/3.
Therefore, the particular solution is[tex]xp(t) = (-2t²/3)cos(t) - (2t/3)sin(t).[/tex]
The general solution for the nonhomogeneous equation is given by x(t) = xh(t) + xp(t),
where xh(t) is the general solution for the homogeneous equation and xp(t) is the particular solution.
Now, to determine the largest interval in which the problem is certain to have a unique twice-differentiable solution, we need to consider any restrictions on the constants c₁ and c₂.
Since we don't have any initial conditions or boundary conditions given, we cannot determine the exact values of c₁ and c₂.
However, we can conclude that the solution is certain to be unique and twice-differentiable on any interval where c₁ and c₂ can take any real values.
Therefore, the largest interval in which the given initial value problem is certain to have a unique twice-differentiable solution is the entire real number line (-∞, +∞).
To know more about interval visit:
https://brainly.com/question/11051767
#SPJ11
Which of the following is NOT a possible cause of aircraft electrical & electronic system failure? Use of sealants Fullscreen Snip Dust Salt ingress Multiple metals in contact
The possible cause of aircraft electrical & electronic system failure can be due to various factors. However, out of the options provided, the one that is NOT a possible cause of such failure is the "Use of sealants."
Sealants are commonly used in aircraft to prevent moisture and other contaminants from entering sensitive electrical and electronic components. They are applied to areas where wires, connectors, or other components are susceptible to exposure. The sealants help maintain the integrity of the system and protect it from external factors.
On the other hand, factors like dust, salt ingress, and multiple metals in contact can contribute to the failure of the aircraft electrical & electronic systems.
1. Dust: Accumulation of dust can interfere with the proper functioning of electrical and electronic components. Dust particles can settle on circuit boards, connectors, or contacts and cause short circuits or poor connections.
2. Salt ingress: Salt can be highly corrosive, and if it enters the electrical and electronic systems of an aircraft, it can lead to corrosion of the components. Corrosion can weaken connections, cause shorts, and affect the overall performance of the system.
3. Multiple metals in contact: When different metals come into contact with each other, it can result in galvanic corrosion. This type of corrosion occurs due to the electrical potential difference between the metals. It can lead to degradation of electrical connections and compromised performance of the system.
In summary, while the use of sealants is essential for protecting aircraft electrical & electronic systems, factors like dust, salt ingress, and multiple metals in contact can potentially cause system failures.
To know more about aircraft electrical :
https://brainly.com/question/32665312
#SPJ11
4.) If something has an electronegative difference of 0.3 , explain why on one hand it is classified as polar, but on the other it is classified as nonpolar? [
A molecule with an electronegative difference of 0.3 can be classified as both polar and nonpolar, depending on the overall molecular geometry and arrangement of the polar bonds within the molecule.
The electronegative difference of 0.3 indicates a small difference in electronegativity between the atoms in the molecule.
On one hand, a molecule with an electronegative difference of 0.3 is classified as polar because there is a partial charge separation within the molecule. This means that one atom has a slightly positive charge while the other atom has a slightly negative charge. This charge separation occurs due to the unequal sharing of electrons between the atoms.
On the other hand, a molecule with an electronegative difference of 0.3 is also classified as nonpolar because the overall molecular geometry may cancel out the partial charges. This can happen when the molecule has a symmetrical shape or when the polar bonds are arranged in such a way that the partial charges balance each other out.
For example, consider the molecule carbon monoxide (CO). Carbon is less electronegative than oxygen, so the oxygen atom attracts the shared electrons more strongly, giving it a partial negative charge. Carbon, on the other hand, has a partial positive charge. Therefore, CO is polar.
However, if we consider the molecule carbon dioxide (CO2), even though each C-O bond is polar, the molecule as a whole is nonpolar. This is because the molecule has a linear shape with the two C-O bonds pointing in opposite directions. The partial charges on the oxygen atoms cancel each other out, resulting in a nonpolar molecule.
In summary, a molecule with an electronegative difference of 0.3 can be classified as both polar and nonpolar, depending on the overall molecular geometry and arrangement of the polar bonds within the molecule.
Learn more about electronegative nonpolar polar:
https://brainly.com/question/18258838
#SPJ11
Please show the process
1. (16 pts) Give a complete and correct name for each of the following molecules. Be sure to indicate stereochemistry where appropriate: (a) (b) (c) (d)
The molecular formula of the molecule is C4H10O. The molecule has an oxygen atom in it, so we can assume that the molecule is an alcohol.
The alcohol has four carbon atoms which suggest that it is butanol. Since there are four carbon atoms, we must determine the position of the hydroxyl group. The alcohol must be placed on the second carbon atom since it is numbered from the end of the carbon chain that is nearest to the hydroxyl group. The complete and correct name of the molecule is 2-butanol.The molecular formula of the molecule is C5H12. The molecule has no functional group in it, so it is an alkane. The alkane has five carbon atoms, and it is named pentane. Since there is no functional group to indicate stereochemistry, we assume that the molecule is a straight-chain pentane. molecule is n-pentane.
The molecular formula of the molecule is C5H10. The molecule has no functional group in it, so it is an alkene. The alkene has five carbon atoms, and it is named pentene. Since there is no functional group to indicate stereochemistry, we assume that the molecule is a straight-chain pentene. The double bond is located between the second and third carbon atoms.
To know more about formula, visit:
https://brainly.com/question/20748250
#SPJ11
15) Which of the following statements is not true when describing what happens to a cell with a concentration of 2.5% m/v NaCl is placed into a solution with a 0.9 % m/v NaCl.
A) The cell solution has the higher osmotic pressure.
B) Water flows into the cell from the surrounding solution.
C) The cell expands.
D) The surrounding solution has a higher osmotic pressure
The statement that is not true when describing what happens to a cell with a concentration of 2.5% m/v NaCl placed into a solution with a 0.9% m/v NaCl is: A) The cell solution has the higher osmotic pressure. The correct statement would be that the surrounding solution has a lower osmotic pressure.
When a cell with a concentration of 2.5% m/v NaCl is placed into a solution with a 0.9% m/v NaCl, the following statements describe what happens to the cell:
A) The cell solution has a higher osmotic pressure: This statement is not true. Osmotic pressure is determined by the concentration of solute particles in a solution. Since the cell solution and the surrounding solution have different concentrations of NaCl, their osmotic pressures will also differ. In this case, the surrounding solution with a concentration of 0.9% m/v NaCl will have a lower osmotic pressure than the cell solution with a concentration of 2.5% m/v NaCl.
B) Water flows into the cell from the surrounding solution: This statement is true. When two solutions with different concentrations are separated by a semipermeable membrane, water tends to move from an area of lower solute concentration to an area of higher solute concentration. In this case, the surrounding solution with a lower concentration of NaCl (0.9% m/v) will have a lower solute concentration compared to the cell solution (2.5% m/v). As a result, water will flow into the cell to equalize the solute concentrations.
C) The cell expands: This statement is true. As water flows into the cell, the volume of the cell increases, causing it to expand. This process is known as osmosis.
D) The surrounding solution has a higher osmotic pressure: This statement is true. As mentioned earlier, osmotic pressure is determined by the concentration of solute particles in a solution. Since the surrounding solution has a lower concentration of NaCl (0.9% m/v) compared to the cell solution (2.5% m/v), the surrounding solution will have a lower osmotic pressure.
Learn more about osmosis:
https://brainly.com/question/2811191
#SPJ11
What is the density of a certain liquid whose specific weight is 99.6 lb/ft3? Express your answer in g/cm³. 2. A moving plate is 15mm from a fixed plate. If the moving plate requires a force per unit area of 15 Pa to maintain a speed of 0.70 m/s, determine the viscosity of the substance between the two plates.
Density of a certain liquid:Specific weight is also called the weight density of a liquid and it's given as .Therefore, the viscosity of the substance between the two plates is 0.32 Pa.s.
w = ρgwhere
w = weight density,
ρ = density of the liquid,
g = acceleration due to gravity.
Now, we can express the density of the liquid as;
ρ = w/g = 99.6 lb/ft³ / 32.2 ft/s²
= 3.1 kg/m³
Now, we can convert the density from kg/m³ to g/cm³ as follows;
ρ = 3.1 kg/m³ x 1000 g/kg / (100 cm/m)³
= 0.0031 g/cm³
Therefore, the density of the certain liquid is 0.0031 g/cm³2. Viscosity of the substance between two plates:We can find the viscosity of the substance between the two plates by using the formula;
F/A = μv/dwhere F/A is the shear stress,
μ is the viscosity of the substance,
v is the velocity of the moving plate,
d is the distance between the plates. Substituting the values given into the formula, we have;
15 Pa = μ(0.70 m/s) / 0.015 mμ
= 15 Pa x 0.015 m / 0.70 m/sμ
= 0.32 Pa.s
To know more about weight visit:
https://brainly.com/question/28532216
#SPJ11
Use the quotient rule to find the derivative of the following.
y= (x^2−3x+7)/(x^2+9)
y′=
Answer: derivative of the given function y = (x^2 - 3x + 7)/(x^2 + 9) is :
y' = (15x - 27) / (x^2 + 9)^2.
To find the derivative of the given function using the quotient rule, we need to follow these steps:
1. Identify the numerator and denominator of the function:
Numerator: x^2 - 3x + 7
Denominator: x^2 + 9
2. Apply the quotient rule, which states that the derivative of a quotient of two functions is equal to:
(f'(x)g(x) - f(x)g'(x)) / (g(x))^2
3. Differentiate the numerator and denominator separately:
The derivative of the numerator (f(x)) is:
f'(x) = d/dx (x^2 - 3x + 7) = 2x - 3
The derivative of the denominator (g(x)) is:
g'(x) = d/dx (x^2 + 9) = 2x
4. Plug these values into the quotient rule formula:
y' = ((2x - 3)(x^2 + 9) - (x^2 - 3x + 7)(2x)) / (x^2 + 9)^2
5. Simplify the expression:
y' = (2x^3 + 18x - 3x^2 - 27 - 2x^3 + 6x^2 - 14x) / (x^2 + 9)^2
Combining like terms:
y' = (15x - 27) / (x^2 + 9)^2
Therefore, the derivative of the given function y = (x^2 - 3x + 7)/(x^2 + 9) is y' = (15x - 27) / (x^2 + 9)^2.
Learn more about derivative of the given function:
https://brainly.com/question/33835031
#SPJ11
Determine the period. (2)
Answer:
19 units
Step-by-step explanation:
You want the period of the shifted sine function shown on the graph.
PeriodThe period is the horizontal distance on the graph between corresponding points. That is, the graph repeats itself after 1 period.
Here, we can find the period by looking at the horizontal distance between the maximum points on the curve. The first one is at 1 unit from the vertical axis; the second one is at 20 units from the vertical axis. The distance between them is ...
20 -1 = 19 . . . . units
The period of the function shown in the graph is 19 units.
__
Additional comment
In general, you want to look for places where an identifiable feature of the graph is found on a grid line. The zero-crossings are not on grid lines, nor are the minimum points. The peaks (maximum points) both appear to be on grid lines, so that is why we chose to use them.
<95141404393>