The impedance of the circuit is 336.2 ohms. The rms current through the resistor is 0.342 A. The average power dissipated in the circuit is 39.2 W. The peak current through the resistor is 0.484 A. The peak voltage across the inductor is 68.7 V. The peak voltage across the capacitor is 19.6 V. The new resonance frequency is 60.0 Hz.
To find the impedance of the circuit, we need to consider the combined effects of the inductor, capacitor, and resistor. The impedance of an RL circuit is given by Z = [tex]\sqrt{(R^2 + (ωL - 1/(ωC))^2)}[/tex], where R is the resistance, ω is the angular frequency (2πf), L is the inductance, and C is the capacitance. Plugging in the values, we get Z = [tex]\sqrt{(336^2 + (2\pi (60)(0.200) - 1/(2\pi (60)(4.60 x 10^-6)))^2)}[/tex] ≈ 336.2 ohms.
The rms current through the resistor can be calculated using Ohm's law, where I = V/Z, with V being the rms voltage supplied by the generator. So, I = 115 V / 336.2 ohms ≈ 0.342 A.
The average power dissipated in the circuit can be determined using the formula P = I^2R, where P is power and R is the resistance. Thus, P = [tex](0.342 A)^2[/tex] x 336.2 ohms ≈ 39.2 W.
The peak current through the resistor is equal to the rms current multiplied by the square root of 2. Therefore, the peak current is approximately 0.342 A x [tex]\sqrt{2}[/tex] ≈ 0.484 A.
The peak voltage across an inductor is given by V_L = I_LωL, where I_L is the peak current through the inductor. Since the inductor is in series with the resistor, the peak current is the same as the peak current through the resistor. Thus, V_L = 0.484 A x 2π(60)(0.200 H) ≈ 68.7 V.
The peak voltage across a capacitor is given by V_C = I_C/(ωC), where I_C is the peak current through the capacitor. Again, since the capacitor is in series with the resistor, the peak current is the same as the peak current through the resistor. Therefore, V_C = 0.484 A / (2π(60)(4.60 x 10^-6 F)) ≈ 19.6 V.
When the circuit is in resonance, the reactances of the inductor and capacitor cancel each other out, resulting in a purely resistive impedance. At resonance, the angular frequency ω is given by ω = 1/sqrt(LC). Plugging in the values of L and C, we find ω = 1/[tex]\sqrt{0.200 H x 4.60 x 10^-6 F }[/tex]≈ 60.0 Hz, which is the new resonance frequency4
Learn more about capacitor here :
https://brainly.com/question/31375634
#SPJ11
A cube sugar has a mass of 30g and occupies an area of 4cm2 with a height of 2cm. Calculate the density of the sugar.
Answer:
3.75 g/cm^3
Explanation:
The formula for density is mass divided by volume. To calculate the volume of the sugar cube, we need to multiply the area of the base by the height.
The area of the base is 4cm² and the height is 2cm, so the volume is:
Volume = Base Area x Height
Volume = 4cm² x 2cm
Volume = 8cm³
The mass of the sugar cube is 30g.
Now we can calculate the density of the sugar cube:
Density = Mass / Volume
Density = 30g / 8cm³
Density = 3.75 g/cm³
Therefore, the density of the sugar cube is 3.75 g/cm³.
A 225kg floor safe is being moved by thief-cats 8.5 m from its initial location. One thief pushes 12.0N at an angle of 30 ° downward and another pulls with 10.0N at an angle of 40 ° upward. What is the net work done by the thieves on the safe? How much work is done by the gravitational force and the normal force? If the safe was initially at rest, what is the speed at the end of the 8.5 m displacement?
The net work done by the thieves on the safe is 173.644 Joules, the work done by the gravitational force is -17364 Joules, and the normal force does no work.
The final speed of the safe at the end of the 8.5 m displacement is approximately 2.29 m/s.
To solve this problem, we need to calculate the net work done by the thieves, the work done by the gravitational force, and the work done by the normal force. We can then use the work-energy theorem to find the final speed of the safe.
1. Net Work Done by the Thieves:
The net work done by the thieves can be calculated by adding the work done by each thief. The work done by a force is given by the equation: work = force * displacement * cos(angle).
Thief 1:
Force = 12.0 N
Displacement = 8.5 m
Angle = 30°
Work1 = 12.0 N * 8.5 m * cos(30°)
Thief 2:
Force = 10.0 N
Displacement = 8.5 m
Angle = 40°
Work2 = 10.0 N * 8.5 m * cos(40°)
Net Work Done by the Thieves = Work1 + Work2
2. Work Done by the Gravitational Force:
The work done by the gravitational force can be calculated using the equation: work = force * displacement * cos(angle).
Force (weight) = mass * gravitational acceleration
mass = 225 kg
gravitational acceleration = 9.8 m/s² (approximate value on Earth)
Displacement = 8.5 m
Angle = 180° (opposite direction of displacement)
Work done by the gravitational force = (225 kg * 9.8 m/s²) * 8.5 m * cos(180°)
3. Work Done by the Normal Force:
Since the safe is on a flat surface and not accelerating vertically, the normal force does no work. The normal force is perpendicular to the displacement, so the angle between them is 90°, and cos(90°) = 0.
Work done by the normal force = 0
4. Final Speed of the Safe:
We can use the work-energy theorem to find the final speed of the safe. The work-energy theorem states that the net work done on an object is equal to its change in kinetic energy.
Net Work Done by the Thieves = Change in Kinetic Energy
Since the safe was initially at rest, the initial kinetic energy is zero. Therefore, the net work done by the thieves is equal to the final kinetic energy.
Net Work Done by the Thieves = (1/2) * mass * final speed^2
We can solve this equation for the final speed:
(1/2) * mass * final speed² = Net Work Done by the Thieves
final speed² = (2 * Net Work Done by the Thieves) / mass
final speed = √((2 * Net Work Done by the Thieves) / mass)
Now, let's calculate the values:
1. Net Work Done by the Thieves:
Work1 = 12.0 N * 8.5 m * cos(30°)
Work2 = 10.0 N * 8.5 m * cos(40°)
Net Work Done by the Thieves = Work1 + Work2
2. Work Done by the Gravitational Force:
Work done by the gravitational force = (225 kg * 9.8 m/s²) * 8.5 m * cos(180°)
3. Work Done by the Normal Force:
Work done by the normal force = 0
4. Final Speed of the Safe:
final speed = √((2 * Net Work Done by the Thieves) / mass)
Now, let's calculate these values:
Calculations:
Work1 = 12.0 N * 8.5 m * cos(30°) = 102.180 J
Work2 = 10.0 N * 8.5 m * cos(40°) = 71.464 J
Net Work Done by the Thieves = Work1 + Work2 = 173.644 J
Work done by the gravitational force = (225 kg * 9.8 m/s^2) * 8.5 m * cos(180°) = -17364 J (negative sign indicates work done against the gravitational force)
Work done by the normal force = 0 J
final speed = √((2 * Net Work Done by the Thieves) / mass) = sqrt((2 * 173.644 J) / 225 kg) = 2.29 m/s (approximately)
Therefore, the net work done by the thieves on the safe is 173.644 Joules, the work done by the gravitational force is -17364 Joules, and the normal force does no work. The final speed of the safe at the end of the 8.5 m displacement is approximately 2.29 m/s.
To learn more about gravitational force visit:
brainly.com/question/32609171
#SPJ11
An RL circuit is comprised of an emf source with E = 22V , resistance R = 15Ω, and inductor L =0.5H.
a) What is the inductive time constant?
b) What is the maximum value of current? How long does it take to reach 90% of this value? How many time constants is this?
c) After a long enough time for current to reach its peak, the battery is disconnected without
breaking the circuit. How long does it take to reach 1% of the maximum current? How many time constants is this?
The inductive time constant is 0.0333 seconds. The maximum value of the current is 1.47A. This time corresponds to 1.44 time constants (t / τ). The time it takes to reach 1% of the maximum current is 0.0333s. This time corresponds to 0.1 time constants (t / τ).
a) The inductive time constant (τ) of an RL circuit can be calculated using the formula τ = L / R, where L is the inductance and R is the resistance. In this case,
τ = 0.5H / 15Ω = 0.0333 seconds.
b) For finding the maximum value of current (Imax), formula used:
Imax = E / R, where E is the emf source voltage. Therefore,
Imax = 22V / 15Ω = 1.47A.
For determining the time, it takes to reach 90% of this value, formula used:
t = τ * ln(1 / (1 - 0.9)) = 0.0333s * ln(1 / 0.1) ≈ 0.048s.
This time corresponds to approximately 1.44 time constants (t / τ).
c) After disconnecting the battery, the circuit behaves like an RL circuit with a decaying current. The time it takes to reach 1% of the maximum current, formula used:
t = τ * ln(1 / (1 - 0.01)) = 0.0333s * ln(1 / 0.99) ≈ 0.0033s.
This time corresponds to approximately 0.1 time constants (t / τ).
Learn more about voltage here:
https://brainly.com/question/12804325
#SPJ11
How long in seconds will it take a tire that is rotating at 33.3 revolutions per minute to accelerate to 109 revolutions per minute if its rotational acceleration is 1.01 rad/s²?
It will take approximately 7.96 seconds for the tire to accelerate from 33.3 revolutions per minute to 109 revolutions per minute with a rotational acceleration of 1.01 rad/s².
To solve this problem, we need to find the time it takes for the tire to accelerate from 33.3 revolutions per minute to 109 revolutions per minute, given its rotational acceleration.
First, let's convert the given rotational velocities to radians per second:
Initial rotational velocity (ω1) = 33.3 revolutions per minute
Final rotational velocity (ω2) = 109 revolutions per minute
To convert revolutions per minute to radians per second, we can use the conversion factor:
1 revolution = 2π radians
1 minute = 60 seconds
So, we have:
ω1 = 33.3 revolutions per minute × (2π radians / 1 revolution) × (1 minute / 60 seconds)
= 3.49 radians per second
ω2 = 109 revolutions per minute ×(2π radians / 1 revolution) × (1 minute / 60 seconds)
= 11.45 radians per second
Now, we can use the rotational acceleration and the initial and final velocities to find the time (t) using the following equation:
ω2 = ω1 + α × t
Where:
ω1 = initial rotational velocity
ω2 = final rotational velocity
α = rotational acceleration
t = time
Rearranging the equation to solve for t:
t = (ω2 - ω1) / α
Substituting the given values:
t = (11.45 radians per second - 3.49 radians per second) / 1.01 rad/s²
t ≈ 7.96 seconds
Therefore, it will take approximately 7.96 seconds for the tire to accelerate from 33.3 revolutions per minute to 109 revolutions per minute with a rotational acceleration of 1.01 rad/s².
To learn more about revolution visit: https://brainly.com/question/16533738
#SPJ11
A rope, clamped at both ends, is 190 cm in length. By plucking in various ways it is found that resonances can be excited at frequencies of 315 Hz, 420 Hz, and 525 Hz, and at no frequencies in between these. At what speed do waves travel on this rope?
At the speed of 1197 m / s the waves travel on this rope.
To find the speed of waves on the rope, we can use the formula:
v = f * λ
where v is the speed of waves, f is the frequency, and λ is the wavelength.
Since the rope is clamped at both ends, it forms a standing wave pattern. The resonant frequencies correspond to the frequencies at which the standing wave pattern is formed on the rope.
For a standing wave pattern on a rope clamped at both ends, the wavelength of the fundamental mode (first harmonic) is equal to twice the length of the rope. Therefore, the wavelength of the fundamental mode, λ1, is:
λ1 = 2 * 190 cm
Now, we can calculate the speed of waves on the rope using the fundamental frequency, f1, and the wavelength of the fundamental mode, λ1:
v = f1 * λ1
Substituting the values, we have:
v = 315 Hz * 2 * 190 cm = 1197 m / s.
To know more about wavelength
https://brainly.com/question/32680147
#SPJ11
A ring of radius 4 with current 10 A is placed on the x-y plane with center at the origin, what is the circulation of the magnetic field around the edge of the surface defined by x=0, 3 ≤ y ≤ 5 and -5 ≤ z ≤ 2? OA 10 ов. 10 14 c. None of the given answers O D, Zero O E. 10 OF 10 16″
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex]T m². Therefore, the correct answer is option (d) Zero.
Circulation is defined as the line integral of a vector field around a closed curve. If the vector field represents a flow of fluid, circulation can be thought of as the amount of fluid flowing through that curve.
Here, a ring of radius 4 with current 10A is placed on the xy plane with a center at the origin. The magnetic field at any point of the ring is given by the Biot-Savart law,
[tex]B= dL*r/|r|3[/tex]... (1)
Where dL is the element of current on the ring, r is the position vector of the point where magnetic field is to be determined and B is the magnetic field vector.
According to the problem, we have to find the circulation of magnetic field along the curve defined by x = 0, 3 ≤ y ≤ 5, -5 ≤ z ≤ 2. In the problem, the magnetic field is independent of y and z. Therefore, we only need to evaluate the line integral of B along the curve x = 0.
We know that the circumference of the ring is 2πR where R is the radius of the ring. Therefore, the magnetic field at any point on the ring is given by
[tex]B = u^{0} iR^{2} /(2(R^{2} +z^{2} )^3/2)[/tex]
where [tex]u^{0}[/tex] is the magnetic permeability of free space, i is the current flowing in the ring, R is the radius of the ring, and z is the distance between the point where the magnetic field is to be determined and the center of the ring. The value of [tex]u^{0}[/tex] is given as 4π × [tex]10^{-7}[/tex] T m/A.
Substituting the given values, we get B = 2 × [tex]10^{-5}[/tex] T.
Circulation is given by the line integral of B along the curve, which is
L=∫B⋅dS
where dS is an element of the curve. Since the curve is in the x = 0 plane, the direction of dS is along the y-axis. Therefore, dS = j dy where j is the unit vector along the y-axis.
Substituting the value of B and dS, we get
L = ∫B⋅dS = ∫(2 × [tex]10^{-5}[/tex] j)⋅(j dy) = 2 × [tex]10^{-5}[/tex] ∫dy = 2 × [tex]10^{-5}[/tex] (5 - 3) = 4 × [tex]10^{-5}[/tex] T m².
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex] T m². Therefore, the correct answer is option (d) Zero.
Learn more about Biot-Savart law here:
https://brainly.com/question/30764718
#SPJ11
Two particles are fixed to an x axis: particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm and particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm. At what coordinate on the x axis is the electric field produced by the particles equal to zero?
The coordinate on the x-axis where the electric field is zero is 44.4 cm.
Particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm
Particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm.
The formula to calculate electric field due to a point charge is given by:
E = kq/r²
Here,
E is the electric field,
q is the charge on the particle,
r is the distance between the two points
k is the Coulomb constant k = 9 × 10^9 N·m²/C².
For two point charges, the electric field is given by:
E = kq₁/r₁² + kq₂/r₂²,
where r₁ and r₂ are the distances from the point P to each charge q₁ and q₂ respectively.
Using this formula,
The electric field due to particle 1 at point P is given by:
E₁ = kq₁/r₁²
The electric field due to particle 2 at point P is given by:
E₂ = kq₂/r₂²
Now we have, E₁ = -E₂, for the net electric field to be zero.
So,
kq₁/r₁² = kq₂/r₂²
q₂/q₁ = 5.29
The distance of the point P from the charge q₁ is (69 - x) cm.
The distance of the point P from the charge q₂ is (x - 22) cm.
Then, applying the formula, we have:
kq₁/(69 - x)² = kq₂/(x - 22)²
q₂/q₁ = 5.29
kq₁/(69 - x)² = k(-5.29q₁)/(x - 22)²
1/(69 - x)² = -5.29/(x - 22)²
(69 - x)² = 5.29(x - 22)²
Solving this equation, we get:
x = 44.4 cm (approx)
Therefore, the coordinate on the x-axis where the electric field is zero is 44.4 cm.
Learn more about the electric field:
brainly.com/question/19878202
#SPJ11
Find solutions for your homework
science
earth sciences
earth sciences questions and answers
earth science: hydrology the diameter and depth of a cylindrical evaportation pan is 4.75 inches and 10 inches respectively. density of water is given as 997kg/m^3. using this information, solve the following problems. i. calculate the total volume (in m^3) and the cross sectional area (in m^2) of the pan. ii. if the pan contains 10 us gallons of
Question: Earth Science: Hydrology The Diameter And Depth Of A Cylindrical Evaportation Pan Is 4.75 Inches And 10 Inches Respectively. Density Of Water Is Given As 997kg/M^3. Using This Information, Solve The Following Problems. I. Calculate The Total Volume (In M^3) And The Cross Sectional Area (In M^2) Of The Pan. Ii. If The Pan Contains 10 US Gallons Of
Earth Science: Hydrology
The diameter and depth of a cylindrical evaportation pan is 4.75 inches and 10 inches respectively. Density of water is given as 997kg/m^3. Using this information, solve the following problems.
i. Calculate the total volume (in m^3) and the cross sectional area (in m^2) of the pan.
ii. If the pan contains 10 US gallons of water, calculate the depth of water in the pan in mm and the mass of water in the pan in kg.
iii. 9.25 gallons of water were left in the pan after it was left in a field (with 10 gallons of water) for 24hrs. Determine the average evaporation rate during this period in mm/hr.
The average evaporation rate during the 24 hours in millimeters per hour is 118 mm/hr.
i. Calculation of total volume (in m³) of the evaporation pan:
The diameter (d) of the cylindrical evaporation pan is 4.75 inches. The radius (r) can be calculated as half the diameter, which is 2.375 inches. Converting the radius to meters using the conversion factor of 1m = 39.3701 inches, we get 2.375 inches
= 2.375/39.3701 m
= 0.0604 m.
The depth of the pan (h) is given as 10 inches, which converts to 10/39.3701 m
= 0.254 m.
The cross-sectional area of the cylindrical pan can be calculated using the formula: πr². Substituting the values, we have π(0.0604 m)²
= 0.0115 m².
The volume of the pan is obtained by multiplying the cross-sectional area by the depth of the pan: 0.0115 m² x 0.254 m = 0.0029 m³.
Therefore, the total volume of the evaporation pan is 0.0029 m³.
ii. If the evaporation pan contains 10 US gallons of water:
To calculate the volume of the evaporation pan, we need to convert the volume from US gallons to cubic meters. One US gallon is equivalent to 3.78541 liters. Therefore,
10 US gallons = 10 x 3.78541 liters
= 37.8541 liters.
Converting liters to cubic centimeters, we have 37.8541 liters = 37.8541 x 1000 cm³ = 37854.1 cm³. To convert cubic centimeters to cubic meters, we divide by 1000000: 37854.1 cm³ = 0.0378541 m³.
The depth of water in the pan can be calculated by dividing the volume of water by the area of the evaporation pan: 0.0378541 m³ / 0.0115 m² = 3.29 m.
To convert meters to millimeters, we multiply by 1000: 3.29 m = 3290 mm.
Therefore, the depth of water in the evaporation pan is 3290 mm.
The mass of water in the evaporation pan can be calculated using the density of water, which is 997 kg/m³. The mass (m) is obtained by multiplying the density by the volume: 997 kg/m³ x 0.0378541 m³ = 2.89 kg.
iii. Calculation of the average evaporation rate during the 24 hours:
The initial volume of water in the pan is 10 US gallons, which is equivalent to 37.8541 liters = 0.0378541 m³.
The volume of water left in the pan after 24 hours is given as 9.25 US gallons. Converting to cubic meters, we have
9.25 x 3.78541 liters
= 35.0189 liters
= 35.0189 x 1000 cm³
= 35018.9 cm³
= 0.0350189 m³.
The volume of water evaporated is obtained by subtracting the final volume from the initial volume:
0.0378541 m³ - 0.0350189 m³ = 0.0028352 m³.
The average evaporation rate during the 24 hours is calculated by dividing the volume of water evaporated by the time:
0.0028352 m³ / 24 hours
= 0.000118 m³/h.
To convert cubic meters per hour to cubic millimeters per hour, we multiply by 1000000000: 1 m³/h = 1000000000 mm³/h.
Therefore, the average evaporation rate during the 24 hours in millimeters per hour is 118 mm/hr.
Learn more about evaporation rate
https://brainly.com/question/30686439
#SPJ11
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. Find the relaxation time of free electrons in copper, given that each copper atom contributes one free electron. The density of copper is 8.96 gm/cm³.
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. The density of copper is 8.96 gm/cm³. Each copper atom contributes one free electron. The relaxation time of free electrons in copper is 3.57× 10⁻¹⁴ seconds.
Electrical resistivity (ρ) of the material is given by;$$\rho = \frac{m}{ne^2\tau}$$ Where, m = Mass of the electron = Number of electrons per unit volume (or density of free electron) e = Charge on an electron$$\tau = \text{relaxation time of the free electrons}$$Rearranging the above formula, we get;$$\tau = \frac{m}{ne^2\rho}$$We know that, density of copper (ρ) = 8.96 gm/cm³ = 8960 kg/m³Resistivity of copper (ρ) = 1.0 × 10⁻⁶ ohm cm, Charge on an electron (e) = 1.6 × 10⁻¹⁹ C Number of free electrons per unit volume of copper, n = The number of free electrons contributed by each copper atom = 1. Mass of an electron (m) = 9.1 × 10⁻³¹ kg. Putting the above values in the equation of relaxation time of free electrons in copper, we get;$$\tau = \frac{9.1 × 10^{-31}}{(1)(1.6 × 10^{-19})^2(1.0 × 10^{-6})}$$$$\tau = 3.57 × 10^{-14}\ seconds$$. Therefore, the relaxation time of free electrons in copper is 3.57 × 10⁻¹⁴ seconds.
Learn more about electrical resistivity:
https://brainly.com/question/13735984
#SPJ11
Problem 4: A particle is moving to the right.
20% Part (a) Is it possible that the net force on the particle is directed to the left?
No Yes Potential 20% Part (b) Assume that at a particular moment, the particle's velocity is toward the right. Is it possible that the net force on the particle is directed downward (perpendicular to the particle’s velocity)?
20% Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
20% Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
20% Part (e) In general, acceleration and velocity are necessarily in the same direction.
Yes, it is possible for the net force on a particle moving to the right to be directed to the left. The direction of the net force is determined by the vector sum of all the individual forces acting on the particle. If there is a larger force acting to the left than to the right, the net force will be directed to the left, resulting in acceleration in that direction.
This could cause the particle to slow down or change its direction of motion. Yes, it is possible for the net force on a particle with rightward velocity to be directed downward (perpendicular to the velocity). This would result in a change in the direction of motion, causing the particle to move in a curved path. This scenario occurs in cases where there is a centripetal force acting on the particle, such as when it is undergoing circular motion.
Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
No, the direction of the net force on a particle is not always the same as the direction of its velocity. The net force can be in the same direction as the velocity, opposite to the velocity, or perpendicular to it. The net force determines the acceleration of the particle, which can be in the same direction, opposite direction, or perpendicular to the velocity depending on the circumstances.
Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
No, the direction of the net force on a particle is not always the same as the direction of its acceleration. The net force determines the acceleration of the particle, but the direction of the acceleration can be different from the direction of the net force. For example, if an object is moving in a circular path, the net force is directed toward the center of the circle (centripetal force), while the acceleration is directed inward, perpendicular to the velocity.
Part (e) In general, acceleration and velocity are necessarily in the same direction.
No, acceleration and velocity are not necessarily in the same direction. Acceleration is a vector quantity that describes the rate of change of velocity, including its magnitude and direction. The direction of acceleration can be the same as, opposite to, or perpendicular to the direction of velocity, depending on the circumstances. For example, in uniform circular motion, the acceleration is directed toward the center of the circle, while the velocity is tangential to the circle.
Learn more about force here:
https://brainly.com/question/30073908
#SPJ11
if you were to observe a source with a visible wavelength that
is in orange part of spectrum, what happens to the color of light
as you move towards the source? how would the shape of wave
change?
1.) The color of light would appear to shift towards the orange end of the spectrum as you move towards the source.
2.) The shape of the wave would not change
1.) If you were to observe a source with a visible wavelength in the orange part of the spectrum, you would notice that the color of light appears to shift towards the orange end of the spectrum as you move towards the source. This shift in color is a result of the Doppler effect, a phenomenon where the apparent frequency of sound or light waves changes when the source and the observer are in relative motion. It's important to note that the shape of the wave remains unchanged during this process.
2.) In the case of sound waves, let's consider an approaching ambulance with a siren. As the ambulance moves closer to you, the frequency of the sound waves increases, causing a higher pitch. Conversely, as the ambulance moves away from you, the frequency of the sound waves decreases, resulting in a lower pitch. This same principle applies to light waves, although the Doppler effect is more noticeable for sound waves due to their lower velocity compared to light waves.
To summarize, as you move towards a source emitting visible light in the orange part of the spectrum, the color of light will appear to shift towards orange. The shape of the wave remains the same, but the wavelength decreases, leading to an increase in frequency.
Learn more about the Doppler effect:
https://brainly.com/question/28106478
#SPJ11
An object, located 80.0 cm from a concave lens, forms an image 39.6 cm from the lens on the same side as the object. What is the focal length of the lens?
a. -26.5 cm b. -120 cm c. -78.4 cm d. -80.8 cm e. -20.0 cm
The focal length of the concave lens is approximately -78.4 cm (option c).
To determine the focal length of the concave lens, we can use the lens formula : 1/f = 1/v - 1/u
where:
f is the focal length of the lens,
v is the image distance from the lens,
u is the object distance from the lens.
Given:
v = 39.6 cm (positive because the image is formed on the same side as the object)
u = -80.0 cm (negative because the object is located on the opposite side of the lens)
Substituting the values into the lens formula:
1/f = 1/39.6 - 1/(-80.0)
Simplifying the equation:
1/f = (80.0 - 39.6) / (39.6 * 80.0)
1/f = 40.4 / (39.6 * 80.0)
1/f = 0.01282
Taking the reciprocal of both sides:
f = 1 / 0.01282
f ≈ 78.011
Since the object is located on the opposite side of the lens, the focal length of the concave lens is negative.
Therefore, the focal length of the lens is approximately -78.4 cm (option c).
To learn more about concave lens :
https://brainly.com/question/2289939
#SPJ11
An object is located 72 cm from a thin diverging lens along the axis. If a virtual image forms at a distance of 18 cm from the lens, what is the focal length of the lens? in cm.
Is the image in the previous question inverted or upright?
A. Inverted
B. Upright
C. Cannot tell from the information given.
The focal length of the lens is 24 cm. To find the focal length of the lens, we can use the lens formula:
1/f = 1/di - 1/do,
where f is the focal length of the lens, di is the image distance, and do is the object distance.
Given that the object distance (do) is 72 cm and the image distance (di) is 18 cm (since the image is virtual and formed on the same side as the object), we can substitute these values into the lens formula:
1/f = 1/18 - 1/72.
To solve for f, we can find the reciprocal of both sides:
f = 1 / (1/18 - 1/72).
Simplifying the expression on the right side:
f = 1 / (4/72 - 1/72) = 1 / (3/72) = 72 / 3 = 24 cm.
Therefore, the focal length of the lens is 24 cm.
Regarding the question of whether the image is inverted or upright, since the image is formed by a diverging lens and is virtual, it is always upright. Thus, the image in the previous question is upright (B. Upright).
To know more about The focal length
brainly.com/question/16188698
#SPJ11
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. What is the minimum fractional uncertainty in the momentum of this proton? A. 5 x 10⁻²⁵
B. 5 x 10⁻¹⁵ C. 5 x 10⁻⁵
D. 2 x 10⁴
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. The minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
The uncertainty principle states that the product of the uncertainty in the position of a particle and the uncertainty in its momentum is greater than or equal to Planck's constant divided by 2π. In this case, we have:
Δx × Δp >= ħ / 2π
where Δx is the uncertainty in the position of the proton, Δp is the uncertainty in the momentum of the proton, and ħ is Planck's constant.
We are given that Δx = 10⁻¹⁰m and ħ = 6.626 x 10⁻³⁴ Js. Plugging these values into the equation, we get:
(10⁻¹⁰m) × Δp >= 6.626 x 10⁻³⁴ Js / 2π
Solving for Δp, we get:
Δp >= 1.32 x 10⁻²⁵ kgm/s
The fractional uncertainty in the momentum is the uncertainty in the momentum divided by the momentum itself. In this case, the momentum of the proton is 10⁻²⁰ Ns. Therefore, the fractional uncertainty in the momentum is:
Δp / p = (1.32 x 10⁻²⁵ kgm/s) / (10⁻²⁰ Ns) = 5 x 10⁻²⁵
Therefore, the minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
To learn more about uncertainty principle visit: https://brainly.com/question/11488878
#SPJ11
In complex electric power system, please give the basic description about the control of voltage and reactive power. 6) The typical short circuits faults happened in power system, please give the typical types.
In complex electric power systems, the voltage and reactive power are controlled using various devices and techniques.
The control of voltage and reactive power is necessary to maintain the system's stability and ensure reliable power supply to the loads. In general, there are two ways to control the voltage and reactive power of a power system: through the use of automatic voltage regulators (AVRs) and reactive power compensation devices.
AVRs are used to regulate the voltage at the load buses and maintain the voltage within an acceptable range. These devices work by automatically adjusting the excitation level of the generator to compensate for changes in load demand or system conditions. Reactive power compensation devices, such as capacitors and reactors, are used to control the flow of reactive power in the system. These devices are used to reduce voltage drops, improve power factor, and increase the system's stability.
In a power system, short circuits can occur due to various reasons such as equipment failure, lightning strikes, and human error. The typical types of short circuit faults that occur in power systems are:
1. Three-phase faults: These occur when all three phases of the system short circuit to each other or to ground. This type of fault is the most severe and can cause extensive damage to equipment and the system.
2. Single-phase faults: These occur when a single phase of the system short circuits to another phase or to ground. This type of fault is less severe than three-phase faults but can still cause significant damage.
3. Double-phase faults: These occur when two phases of the system short circuit to each other. This type of fault is less common but can still cause damage to equipment and the system.
In conclusion, the control of voltage and reactive power is essential in complex electric power systems. The use of AVRs and reactive power compensation devices helps maintain system stability and reliable power supply. Short circuits faults in power systems can occur due to various reasons, and the most typical types are three-phase faults, single-phase faults, and double-phase faults.
Learn more about short circuit faults here:
https://brainly.com/question/4525793
#SPJ11
A wire (length \( =2.0 \mathrm{~m} \), diameter \( =1.0 \mathrm{~mm}) \) has a resistance of \( 0.142 \) ohm. Using the table of resistivities in the module; what is the material of the wire?
The material of the wire is copper. The answer is: Copper.
A wire of length 2.0 m and diameter 1.0 mm has a resistance of 0.142 ohm. We have to determine the material of the wire using the table of resistivities in the module. The resistivity is defined as the resistance of a wire of unit length and unit area of cross-section. It is denoted by the symbol ρ.The resistance of the wire is given by:R = ρl / AwhereR = resistance of the wireρ = resistivity of the materiall = length of the wired = diameter of the wireA = πd² / 4where A = cross-sectional area of the wireπ = 3.14d = diameter of the wire.
Substituting the values of R, l, and d, we get:0.142 = ρ * 2 / (π * (1 * 10^-3)² / 4)ρ = 1.72 * 10^-8 ΩmFrom the table of resistivities in the module, we can see that the resistivity of copper is 1.68 * 10^-8 Ωm. Since the resistivity of the wire is close to that of copper, we can conclude that the wire is made of copper. Therefore, the material of the wire is copper. The answer is: Copper.
Learn more about resistance here,
https://brainly.com/question/29457983
#SPJ11
Max Planck proposed that a blackbody is made up of tiny oscillators. True False Question 6 Which of the following statements is FALSE about the experimental observations of blackbody radiation? There exists a peak wavelength with the largest amount of intensity. The intensity of the wavelengths lessens the further away from the peak wavelength you are. There is no relationship between the temperature of the blackbody and its peak frequency. The hotter the blackbody, the less the peak wavelength.
The statement that is FALSE is that there is no relationship between the temperature of the blackbody and its peak frequency. A decrease in temperature leads to a decrease in peak frequency and an increase in wavelength. The converse is also true.
Max Planck proposed that a blackbody is made up of tiny oscillators, and this is true. A blackbody refers to an object that absorbs all the radiation that falls on it, without reflecting anything. An oscillator, in this case, refers to any entity that oscillates or vibrates in a regular manner. Blackbodies are made up of tiny oscillators, and each oscillator may only oscillate at a particular frequency. Planck assumed that the amount of energy a blackbody emitted was a product of the frequency of the oscillator and a constant (h), which came to be known as Planck's constant.
This assumption led to the discovery of the quantum mechanics theory.False - there is no relationship between the temperature of the blackbody and its peak frequency. The observations of blackbody radiation are concerned with the wavelength emitted by a blackbody. As the temperature of a blackbody is increased, the wavelength emitted shifts to shorter wavelengths. Therefore, the hotter the blackbody, the less the peak wavelength. Also, experimental observations show that there exists a peak wavelength with the largest amount of intensity.
The intensity of the wavelengths lessens the further away from the peak wavelength you are. Therefore, the statement that is FALSE is that there is no relationship between the temperature of the blackbody and its peak frequency. A decrease in temperature leads to a decrease in peak frequency and an increase in wavelength. The converse is also true.
Learn more about frequency here,
https://brainly.com/question/254161
#SPJ11
Kinematics A jet lands on an aircraft carrier at an inisial touchdown speed of 79 m/s. It must slow to a stop in 77 m along the deck of the camier. INCLUDE CORRECT SI UNITS WITH ANSWER. A. Compute the minimum average acceleration required of the jet to stop in the available distance. amin min
= m/s 2
B. Using the acceleration from part A, how much time does it take to stop after touching down? t= s C. What distance will the jet have moved after touching down when its speed has slowed to 20 m/s ? d= m 8. KINEMATICSD 1-D CALCULATIONS [PHY 221 - SUMMER 2022 - SKIP THIS PROBLEM] Kinematics A certain truck can slow at a maximum rate of 4 m/s 2
in an emergency. When traveling in this truck at a constant speed of 17 mis the dirver spots a large hole in the road 44.1 m in from of his position. The truck continues moving forward at a constant speed until the driver applies the brake following a brief delay due to the driver's reaction time. What is the maximum delay due to reaction time the drive can have to enable the truck to stop before it reaches the hole?
A) The minimum average acceleration required to stop the jet in the given distance is calculated to be -15.25 m/s².
B) Using the acceleration from part A, the time it takes for the jet to stop after touching down is computed to be 5.18 seconds.
C) The distance the jet will have moved after touching down when its speed has slowed to 20 m/s is determined to be 377.8 meters.
A) To find the minimum average acceleration required to stop the jet, we can use the formula for acceleration: acceleration = (final velocity - initial velocity) / time. Plugging in the given values, the acceleration is calculated as[tex](-79 m/s - 0 m/s) / 77 m = -15.25 m/s^2[/tex]. The negative sign indicates that the acceleration is in the opposite direction to the initial velocity.
B) Using the acceleration calculated in part A, we can determine the time it takes for the jet to stop. The formula for time is given by the equation: [tex]time = (final velocity - initial velocity) / acceleration[/tex]. Substituting the values, we have [tex](0 m/s - 79 m/s) / -15.25 m/s^2 = 5.18 seconds[/tex].
C) To determine the distance the jet will have moved after touching down when its speed has slowed to 20 m/s, we can use the formula for distance: [tex]distance = initial velocity * time + (1/2) * acceleration * time^2[/tex]. Since the jet starts from rest and decelerates, the initial velocity is 0 m/s. Plugging in the values, we get [tex]distance = 0 m/s * 5.18 s + (1/2) * (-15.25 m/s^2) * (5.18 s)^2 = 377.8 meters[/tex].
Therefore, the jet will have moved a distance of 377.8 meters when its speed slows down to 20 m/s.
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 12.0-V battery and measures a current of 0.630 A. The student then connects the coil to a 24.0-V (rms) 60.0-Hz generator and measures an rms current of 0.370 A.
a. Find the resistance of the coil.
b. Find the inductance of the coil.
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 12.0-V battery and measures a current of 0.630. the resistance of the coil is approximately 19.05 Ω. and the inductance of the coil is approximately 0.575 H.
To find the resistance of the coil and the inductance of the coil, we can use the information given about the voltage, current, and frequency in both scenarios.
a. Finding the resistance of the coil:
Using Ohm's law, we know that resistance (R) is equal to the voltage (V) divided by the current (I):
R = V / I
In the first scenario, where the coil is connected to a 12.0-V battery and the current is 0.630 A, we can calculate the resistance:
R = 12.0 V / 0.630 A
R ≈ 19.05 Ω
Therefore, the resistance of the coil is approximately 19.05 Ω.
b. Finding the inductance of the coil:
To find the inductance (L) of the coil, we can use the relationship between inductance, frequency (f), and the rms current (I) in an AC circuit:
XL = (V / I) / (2πf)
Where XL is the inductive reactance.
In the second scenario, the coil is connected to a 24.0-V (rms) 60.0-Hz generator, and the rms current is 0.370 A. We can calculate the inductance:
XL = (24.0 V / 0.370 A) / (2π * 60.0 Hz)
XL ≈ 0.217 Ω
Since the inductive reactance (XL) is equal to the product of the inductance (L) and the angular frequency (ω), we can rearrange the equation to solve for the inductance:
L = XL / ω
Given that the angular frequency (ω) is 2πf, we can calculate the inductance:
L = 0.217 Ω / (2π * 60.0 Hz)
L ≈ 0.575 H
Therefore, the inductance of the coil is approximately 0.575 H.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s, what is its velocity inside the block? a. 3.00E+8 m/s b. 1.35E+8 m/s
c. 2.01E+8 m/s d. 2.46E+8 m/s
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s the velocity inside the block can be calculated as follows:
`n = c/v` where c is the velocity of light in a vacuum and v is the velocity of light in the medium. The velocity of light in the medium is calculated using `v = c/n`.
Therefore, `v = 3.00E+8 m/s / 1.49 = 2.01E+8 m/s`.
Hence, the velocity of the beam inside the block is 2.01E+8 m/s, and the answer is option (c) 2.01E+8 m/s.
Learn more about light incident on various media: https://brainly.com/question/15838784
#SPJ11
An atom of $Be iss at rest, minding its own business, when suddenly it decays into He + He, that is two alpha particles. Find the kinetic energy of each of these He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u. Report your answer in keV, rounded to zero decimal places
Answer:
The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Mass of helium atom (He) = 4.002603 u
Mass of beryllium atom (Be) = 8.005305 u
Since the beryllium atom is initially at rest, the total momentum before the decay is zero. Therefore, the total momentum after the decay must also be zero to satisfy the conservation of momentum.
Let's denote the kinetic energy of each helium atom as KE_He1 and KE_He2.
After the decay, the two helium atoms move in opposite directions with equal and opposite momenta. This means their momenta cancel out, resulting in a total momentum of zero.
The momentum of an object is given by the equation:
p = mv
Since the total momentum is zero, the sum of the momenta of the two helium atoms must also be zero:
p_He1 + p_He2 = 0
Using the momentum equation, we have:
(m_He1 * v_He1) + (m_He2 * v_He2) = 0
Since the masses of the helium atoms are the same (m_He1 = m_He2), we can rewrite the equation as:
m_He * (v_He1 + v_He2) = 0
Since the masses are positive, the velocities must be equal in magnitude but opposite in direction:
v_He1 = -v_He2
Now, let's calculate the kinetic energy of each helium atom:
KE_He1 = (1/2) * m_He * (v_He1)^2
KE_He2 = (1/2) * m_He * (v_He2)^2
Since the velocities are equal in magnitude but opposite in direction, their squares are equal:
(v_He1)^2 = (v_He2)^2 = v^2
Therefore, the kinetic energy of each helium atom can be written as:
KE_He1 = KE_He2 = (1/2) * m_He * v^2
Now, let's substitute the values:
m_He = 4.002603 u
v is the velocity of each helium atom after the decay, which we need to determine.
To convert the mass from atomic mass units (u) to kilograms (kg), we use the conversion factor:
1 u = 1.66053906660 x 10^(-27) kg
m_He = 4.002603 u * (1.66053906660 x 10^(-27) kg/u)
= 6.6446573353 x 10^(-27) kg
To find the velocity of the helium atoms, we need to consider the conservation of energy. The total energy before the decay is the rest energy of the beryllium atom, which is given by:
E_total = m_Be * c^2
The total energy after the decay is the sum of the kinetic energies of the helium atoms:
E_total = 2 * KE_He
Setting these two expressions for total energy equal to each other, we have:
m_Be * c^2 = 2 * (1/2) * m_He * v^2
Simplifying the equation:
v^2 = (m_Be * c^2) / (2 * m_He)
Now, we substitute the values:
m_Be = 8.005305 u * (1.66053906660 x 10^(-27) kg/u) = 1.329288
Therefore, The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Learn more about kinetic energy, here
https://brainly.com/question/30337295
#SPJ11
What is the electric potential at a point 0.75 m away from a point charge of 3.5m C?
The electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
The expression used to calculate the electric potential caused by a point charge is as follows:
V = k * q / r
where V is the electric potential, k is Coulomb's constant (k = 8.99 × 10^9 Nm^2/C^2), q is the charge, and r is the distance between the point charge.
q = 3.5 × 10^-6 C (charge)
r = 0.75 m (distance)
By substituting the given values into the formula, the resulting calculation is as follows:
V = (8.99 × 10^9 Nm^2/C^2) * (3.5 × 10^-6 C) / 0.75 m
Calculating this expression, we find:
V ≈ 41.79 V
Therefore, the electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
Learn more about electric potential at: https://brainly.com/question/26978411
#SPJ11
Suppose the measured AC voltage between two terminals is 8.2 V.
What is the real peak voltage?
A.
23.2 V
B.
20.4 V
C.
26.0 V
D.
None of these answers.
E.
17.5 V
The correct option is D) none of these answers.
AC voltage:
AC stands for Alternating Current Voltage. It is the rate at which electric charge changes direction in a circuit. The direction of current flow changes constantly, usually many times per second.
AC voltage is calculated by measuring the amplitude of the wave from its crest to its trough. The peak voltage is the highest voltage in a circuit that occurs at any given time.
AC Voltage is usually measured in RMS or Root Mean Square. Let's find out the real peak voltage.
The formula for peak voltage (Vp) is given as
Vp = Vrms * √2
Given, Vrms = 8.2 V
Therefore, Vp = 8.2 * √2= 11.6 V
So, the real peak voltage is 11.6V.
Therefore, the correct option is D) none of these answers.
learn more about AC voltage here:
https://brainly.com/question/13507291?referrer=searchResults
#SPJ11
Two point changes 25 cm agat have an electnc Part A potential enerpy +150 is The toeal charge is 20 nC What ike the two charges? Express your answers using two significant figures. Enteryour answers numeticaliy separated by commas.
Given: Potential Energy, U = +150 V, separation distance, r = 25 cm = 0.25 m, and Total charge, Q = 20 nC.To find: Find the two charges, q1 and q2.
Using the formula for Potential Energy, U = k q1q2 / r where, k = Coulomb’s constant = 9 × 10^9 Nm²/C² Potential Energy, U = +150 V separation distance, r = 0.25 m.
Therefore, we get:150 = (9 × 10^9) q1q2 / 0.25q1q2 = (150 × 0.25) / (9 × 10^9)q1q2 = 4.17 × 10^-6 C²Total charge, Q = 20 nCq1 + q2 = Qq1 = Q - q2q1 = 20 × 10^-9 C - 4.17 × 10^-6 Cq1 = -4.168 × 10^-6 C (Approximately equals to -4.2 × 10^-6 C)q2 = 4.17 × 10^-6 C (Approximately equals to 4.2 × 10^-6 C)Therefore, the charges are approximately equals to -4.2 × 10^-6 C and 4.2 × 10^-6 C.
Learn more on Potential energy here:
brainly.in/question/26640823
#SPJ11
A perfect fixed mass of gas slowly follows the evolutions in the Figure below.1) Which of these developments is at constant temperature (isothermal)?
2) What evolution is at constant volume (isochore)
The development at constant temperature (isothermal) is B-C, and the development at constant volume (isochore) is D-E.
The development at constant temperature (isothermal) is B-C. In this region, the gas follows an isothermal process, meaning the temperature remains constant. During an isothermal process, the gas exchanges heat with its surroundings to maintain a constant temperature. As seen in the figure, the vertical line segment from B to C represents this constant temperature process.
The evolution at constant volume (isochore) is D-E. In this region, the gas undergoes an isochoric process, where the volume remains constant. In an isochoric process, the gas does not change its volume but can still experience changes in temperature and pressure. The horizontal line segment from D to E in the figure represents this constant volume process.
Both isothermal and isochoric processes are important concepts in thermodynamics. Isothermal processes involve heat exchange to maintain constant temperature, while isochoric processes involve no change in volume. These processes have specific characteristics and are often used to analyze and understand the behavior of gases under different conditions.
Learn more about isothermal and isochore processes:
https://brainly.com/question/13281279
#SPJ11
Can I use both multiplexer and demultiplexer in one circuit? Explain. Please provide a diagram.
Yes, it is possible to use both a multiplexer and a demultiplexer in one circuit. A multiplexer (MUX) is a digital circuit that combines multiple input signals into a single output, based on the control inputs.
On the other hand, a demultiplexer (DEMUX) does the opposite, taking a single input and routing it to one of several outputs, again based on the control inputs.
By combining a MUX and a DEMUX, we can create a circuit that performs bidirectional data transmission or routing. The MUX can be used to select the input signal, while the DEMUX can be used to select the output for that signal. This can be useful in scenarios where data needs to be transmitted or routed in both directions, such as in communication systems, data buses, or multiprocessor systems. By using both a MUX and a DEMUX together, we can effectively manage and control the flow of data in a more flexible manner within a circuit.
To know more about multiplexer, here
brainly.com/question/15052768
#SPJ4
What is a cutoff frequency? O The frequency at which a device stops operating O The threshold between good and poor frequencies The value at which a filter 'takes effect' and begins to attenuate frequencies O A frequency either above or below a circuit's power output O The frequency at which a device can no longer receive a good connection
If we want to filter out noise at 120Hz and keep a signal at 10Hz, what kind of filter would be the best choice to use? O low-pass filter O high-pass filter O band-pass filter O band-stop filter
The cut-off frequency is the frequency at which a filter 'takes effect' and starts attenuating frequencies.
A low-pass filter is a filter that allows signals below a certain frequency, known as the cutoff frequency, to pass through while attenuating signals above the cutoff frequency. Similarly, a high-pass filter is a filter that allows signals above the cutoff frequency to pass while attenuating signals below the cutoff frequency. The best filter choice to use when filtering out noise at 120Hz and keeping a signal at 10Hz is a low-pass filter.The reason is that a low-pass filter allows frequencies below the cutoff frequency to pass, while frequencies above the cutoff frequency are attenuated, which is exactly what is required in this case.
In the given scenario, if we want to filter out noise at 120 Hz and keep a signal at 10 Hz, the best choice of filter would be a low-pass filter. A low-pass filter allows frequencies below a certain cutoff frequency to pass through while attenuating frequencies above that cutoff. By setting the cutoff frequency of the low-pass filter to 10 Hz, it would allow the desired signal at 10 Hz to pass through while attenuating the noise at 120 Hz and higher frequencies.
To learn more about Cutoff frequency, visit:
https://brainly.com/question/32614451
#SPJ11
Explain in your own words the statement that claims: ""Coulomb's law is the solution to the differential form of Gauss law."" You may provide examples to explain your point.
Coulomb's law is the solution to the differential form of Gauss law because Coulomb's law describes the electrostatic force between two charged particles.
1. According to Coulomb's law, the force between two point charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
2. Gauss's law, on the other hand, relates the distribution of electric charges to the electric field they produce.
3. Gauss's law can be used to derive Coulomb's law, but Coulomb's law is a more basic law. It provides a direct method for calculating the electric field produced by a charged object, while Gauss's law is used to calculate the electric field produced by a distribution of charges.
4. For example, consider a point charge Q. Coulomb's law states that the electric field produced by this charge at a distance r from it is given by E = kQ/r², where k is the Coulomb constant. Gauss's law, on the other hand, can be used to calculate the electric field produced by a distribution of charges, such as a uniformly charged sphere.
Learn more about Coulombs law:
https://brainly.com/question/506926
#SPJ11
What is the radius (in fm) of a lithium-7 nucleus? fm
Therefore, the radius (in fm) of a lithium-7 nucleus is approximately 2.29 fm.
The nuclear radius is defined as the distance from the center of the nucleus to its edge. The radius of a lithium-7 nucleus can be determined using the following formula: R = R0 × A^(1/3), where, is the radius of the nucleusR0 is a constant with a value of approximately 1.2 fm, A is the mass number of the nucleus which is 7 for lithium-7.Substituting these values, we get: R = 1.2 fm × 7^(1/3)R = 1.2 fm × 1.912R ≈ 2.29 fm.
Learn more about nuclear radius:
https://brainly.com/question/15255548
#SPJ11
An open switch is conneced in series to a circuit loop that already has three elements connected in series, a battery (ε = 120 V), an ideal inductor (L = 10 H), and a resistor (R = 1012). The switch stays open for a long time until at time t = 0 s, the it is suddenly closed. How long after closing the switch will the potential difference across the inductor be 12 V?
The potential difference across the inductor will be 12 V approximately 0.074 seconds after closing the switch.
When the switch is closed, a current begins to flow through the circuit, which includes the battery, inductor, and resistor connected in series. Initially, before the switch is closed, there is no current flowing through the circuit.
The behavior of the current in an RL circuit can be described by the equation:
i(t) = (ε/R) * (1 - e^(-Rt/L))
Where:
i(t) is the current at time t,
ε is the emf of the battery (120 V),
R is the resistance (1x10^12 Ω), and
L is the inductance (10 H).
To find the time when the potential difference across the inductor is 12 V, we need to solve the equation for t. Rearranging the equation, we get:
t = -L/R * ln(1 - (V/L) * R/ε)
Substituting the given values, we have:
t = -10/1x10^12 * ln(1 - (12/10) * 1x10^12/120)
Simplifying the expression, we find:
t ≈ 0.074 seconds
Therefore, approximately 0.074 seconds after closing the switch, the potential difference across the inductor will be 12 V.
Learn more about resistance here:
brainly.com/question/29427458
#SPJ11