Answer:
The focal length, f = − 15 2 c m = − 7.5 c m The object distance, u = -10 cm Now from the mirror equation 1 v + 1 u = 1 f 1 v + 1 − 10 = 1 − 7.5 v = 10 × 7.5 − 2.5 = − 30 c m The image is 30 cm from the mirror on the same side as the object.
A Zehrs truck loaded with cannonball watermelons stops suddenly to avoid running over the edge of a washed out bridge. The quick stop causes a number of melons to fly off of the truck. One melon rolls over the edge of the road with an initial velocity of 10 m/s in the horizontal direction. The river valley has a parabolic cross-section matching the equation y 2
=16x where x and y are measured in metres with the vertex at the road edge. What are the x and y components of where the watermelon smashes onto the river valley?
x = 4.0816 m and y = 10.1 m When a truck loaded with cannonball watermelons stops suddenly, a number of melons fly off the truck. One melon rolls over the edge of the road with an initial velocity of 10 m/s in the horizontal direction.
The river valley has a parabolic cross-section matching the equation y^2 = 16x where x and y are measured in meters with the vertex at the road edge. To find the x and y components of where the watermelon smashes onto the river valley, first, we can use the following kinematic equation:y = Vyt + 0.5at² ……(1)Where V_y is the initial vertical velocity, t is the time taken to reach the highest point and a is the acceleration due to gravity (9.8 m/s²).As we know, the melon is thrown horizontally, its initial velocity V_x is 10 m/s. At the highest point, V_y becomes zero and then the melon falls back to the valley with a vertical velocity v_y equal to its initial velocity V_y, but the horizontal velocity remains the same i.e. V_x. Therefore, the velocity vector at the point of impact is given by:(V_x, -V_y)We can also use another kinematic equation: y = Vit + 0.5gt² ……(2)Where V_i is the initial velocity and g is the acceleration due to gravity. Substituting the given values, we get:10t = 4x ……(3)t = 0.4x, Substituting (3) in (1), we get:y = V_y (0.4x) + 0.5 (9.8) (0.4x)²y = 0.4 V_y x + 1.568 x²Putting V_y = 0, as there is no initial vertical velocity, we get:y = 1.568 x²Substituting V_x = 10 m/s in (3), we get:x = 0.4t = 0.4 (10/9.8) = 0.40816 s, Therefore, x = 4.0816 m and y = 10.1 m.
To know more about direction visit:
https://brainly.com/question/29132707
#SPJ11
What formula is used to find the experimental equivalent resistance?
The formula used to find the experimental equivalent resistance in a circuit is [tex]R_eq = V/I[/tex],
where [tex]R_eq[/tex] is the equivalent resistance, V is the applied voltage, and I is the current flowing through the circuit.
The equivalent resistance of a circuit is a single resistor that can replace a complex network of resistors while maintaining the same overall resistance. It represents the combined effect of all the resistors in the circuit.
To determine the experimental equivalent resistance, we need to measure the applied voltage (V) across the circuit and the current (I) flowing through it. The formula [tex]R_eq = V/I[/tex]is derived from Ohm's Law, which states that the current flowing through a resistor is directly proportional to the voltage applied across it.
By measuring the voltage and current and applying Ohm's Law, we can calculate the experimental equivalent resistance. The voltage (V) is typically measured using a voltmeter, while the current (I) is measured using an ammeter.
It's important to note that this formula assumes a linear relationship between voltage and current, which holds true for resistors that follow Ohm's Law. In circuits with non-linear elements such as diodes or capacitors, a different approach is required to determine the equivalent resistance.
Learn more about resistance
https://brainly.com/question/17563681
#SPJ11
A cannon ball is launched into the ocean at an angle of 30° above the horizon. The cannonball has an initial speed of 46 m/s. The deck the cannonball is fired from is 11 meters high assume this is the initial height of the cannonball). a.) How long does the cannon ball take to reach the ocean? b.) What is the speed of the cannonball just before it lands in the ocean?
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
a.) Time taken by the cannon ball to reach the ocean:The initial velocity of the cannon ball, u = 46 m/sThe angle made by the cannon ball with the horizontal, θ = 30°The vertical component of the initial velocity, v = u × sin θ = 46 × sin 30°= 46/2 = 23 m/sLet the time taken by the cannon ball to reach the ocean be t seconds.The distance covered by the cannon ball in the vertical direction in time t is given byh = ut + 1/2gt²where, g = acceleration due to gravity = 9.8 m/s²Substituting the values,11 = (23)t - 1/2 × 9.8 × t²11 = 23t - 4.9t²On solving this equation, we get two values of t, t = 0.947 seconds or t = 4.795 secondsThe time taken by the cannon ball to reach the ocean is 0.947 seconds.
b.) The speed of the cannonball just before it lands in the ocean:The horizontal component of the initial velocity of the cannon ball,vx = u × cos θ = 46 × cos 30°= 46(√3)/2 = 23 (√3) m/sThe time taken by the cannon ball to reach the ocean, t = 0.947 secondsThe horizontal distance covered by the cannon ball in time t is given byx = vx × t = 23 (√3) × 0.947 = 21.04 mThe vertical component of the final velocity of the cannon ball just before it lands in the ocean,vf = u + gt = 23 + 9.8 × 0.947 = 32.32 m/s
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
Learn more about Speed here,
https://brainly.com/question/13943409
#SPJ11
explain in your own words the following:
1. ATMOSPHERIC OPTICS
2. HUYGEN’S PRINCIPLE AND INTERFERENCE OF LIGHT
3. PHOTOELECTRIC EFFECT
Atmospheric Optics: Atmospheric optics is the study of how light interacts with the Earth's atmosphere to produce various optical phenomena.
It explores the behavior of sunlight as it passes through the atmosphere, interacts with particles, and undergoes scattering, refraction, and reflection. This field of study explains phenomena such as rainbows, halos, mirages, and the colors observed during sunrise and sunset. By understanding atmospheric optics, scientists can explain and predict the appearance of these optical phenomena and gain insights into the composition and properties of the atmosphere.
Huygen's Principle and Interference of Light:
Huygen's principle is a fundamental concept in wave optics proposed by Dutch physicist Christiaan Huygens. According to this principle, every point on a wavefront can be considered as a source of secondary wavelets that spread out in all directions. These secondary wavelets combine together to form a new wavefront. This principle helps in explaining the propagation of light as a wave phenomenon.
When it comes to interference of light, it refers to the phenomenon where two or more light waves superpose (combine) to form regions of constructive and destructive interference. Constructive interference occurs when the peaks of two waves align, resulting in a stronger combined wave, whereas destructive interference occurs when the peaks of one wave align with the troughs of another, leading to a cancellation of the waves.
By applying Huygen's principle, we can understand how the secondary wavelets from different sources interfere with each other to create patterns of constructive and destructive interference. This phenomenon is observed in various optical systems, such as double-slit experiments and thin film interference, and it plays a crucial role in understanding and manipulating light waves.
Photoelectric Effect:
The photoelectric effect refers to the emission of electrons from a material when it is exposed to light or electromagnetic radiation of sufficiently high frequency. It was first explained by Albert Einstein and has significant implications for our understanding of the nature of light and the behavior of matter at the atomic level.
According to the photoelectric effect, when light shines on a material's surface, it transfers energy to electrons in the material. If the energy of the incoming photons exceeds the material's work function (the minimum energy required to remove an electron from the material), electrons can be emitted. The emitted electrons are known as photoelectrons.
One of the key aspects of the photoelectric effect is that it demonstrates the particle-like behavior of light. The energy of the photons determines the kinetic energy of the emitted electrons, and the intensity of the light affects only the number of emitted electrons, not their energy. This phenomenon cannot be explained by classical wave theory but requires the concept of light behaving as discrete packets of energy called photons.
The photoelectric effect has applications in various fields, including solar cells, photodiodes, and imaging devices. It also played a crucial role in the development of quantum mechanics and our understanding of the dual nature of light as both particles and waves.
To know more about Huygen's Principle
https://brainly.com/question/2127578
#SPJ11
A force that varies with time F- 19t3 acts on a sled (to the right, in the positive direction) of mass 60 kg from t₁ = 14 seconds to t₂ -3.5 seconds. If the sled was initially moving TO THE LEFT (in the negative direction) at an initial speed of 29 m/s, determine the final velocity of the sled. Record your answer with at least three significant figures. IF your answer is negative (to the left), be sure to include a negative sign with your answer!
Answer:
The final velocity of the sled is approximately -1688.3 m/s in the negative direction.
Mass of the sled (m) = 60 kg
Force acting on the sled (F) = 19t^3 N,
where t is the time in seconds.
Initial velocity of the sled (v_initial) = -29 m/s
To find the final velocity, we'll integrate the force function over the given time interval and apply the initial condition.
The integral of 19t^3 with respect to t is (19/4)t^4.
Let's denote it as F_integrated.
F_integrated = (19/4)t^4
Now, let's calculate the change in momentum:
Δp = F_integrated(t₂) - F_integrated(t₁)
Substituting the time values:
Δp = (19/4)(t₂^4) - (19/4)(t₁^4)
Δp = (19/4)(-3.5^4) - (19/4)(14^4)
Δp = (19/4)(-150.0625) - (19/4)(38416)
Δp = -7129.8125 - 92428
Δp ≈ -99557.8125 kg·m/s
Using the definition of momentum (p = mv), we can relate the change in momentum to the final velocity:
Δp = m(v_final - v_initial)
-99557.8125 = 60(v_final - (-29))
Simplifying:
-99557.8125 = 60(v_final + 29)
Dividing both sides by 60:
-1659.296875 = v_final + 29
Subtracting 29 from both sides:
v_final = -1688.296875 m/s
Therefore, the final velocity of the sled is approximately -1688.3 m/s in the negative direction.
Learn more about velocity here
https://brainly.com/question/80295
#SPJ11
The figure shows four particles, each of mass 30.0 g, that form a square with an edge length of d-0.800 m. If d is reduced to 0.200 m, what is the change in the gravitational potential energy of the f
The change in gravitational potential energy of the four particles when d is reduced to 0.200 m is ΔU = (-6.00687 × 10⁻¹²) (1/0.2 - 1/(d-0.8)).
The given figure shows four particles, each of mass 30.0 g, forming a square with an edge length of d-0.800 m. The change in gravitational potential energy of the four particles can be calculated using the formula:ΔU = Uf - Ui where ΔU is the change in gravitational potential energy, Uf is the final gravitational potential energy, and Ui is the initial gravitational potential energy. The initial gravitational potential energy of the four particles can be calculated using the formula: Ui = -G m² / r where G is the gravitational constant, m is the mass of each particle, and r is the initial distance between the particles. Since the particles form a square with an edge length of d-0.800 m, the initial distance between the particles is:r = d - 0.800 m. The final gravitational potential energy of the four particles can be calculated using the same formula with the final distance between the particles:r' = 0.200 mΔU = Uf - Ui= -G m² / r' - (-G m² / r)= -G m² (1/r' - 1/r)Now, substituting the given values,G = 6.6743 × 10⁻¹¹ m³ / kg s²m = 0.03 kr = d - 0.8 mr' = 0.2 kΔU = (-6.6743 × 10⁻¹¹ × 0.03²) (1/0.2 - 1/(d-0.8))= (-6.6743 × 10⁻¹¹ × 0.0009) (1/0.2 - 1/(d-0.8))= (-6.00687 × 10⁻¹²) (1/0.2 - 1/(d-0.8)). The change in gravitational potential energy of the four particles when d is reduced to 0.200 m is ΔU = (-6.00687 × 10⁻¹²) (1/0.2 - 1/(d-0.8)).
To know more about particles, visit:
https://brainly.com/question/30381265
#SPJ11
In one measurement of the body's bioelectric impedance, values of Z=5.59×10 2
∘ and ϕ=−7.98 ∘
are obtained for the total impedance and the phase angle, respectively. These values assume that the body's resistance R is in series with its capacitance C and that there is no inductance L. Determine the body's (a) resistance and (b) capacitive reactance. (a) Number Units" (b) Number Units
(a) Resistance (R) = 553.372 Ω.
(b) Capacitive reactance (Xc) = 77.118 Ω.
In one measurement of the body's bioelectric impedance, values of Z = 5.59×10^2° and ϕ = −7.98° are obtained for the total impedance and the phase angle, respectively.
These values assume that the body's resistance R is in series with its capacitance C and that there is no inductance L.
Determine the body's (a) resistance and (b) capacitive reactance. (a)Number = 460.49 Units = Ω
(b)Number = 395.26 Units = Ω
In this problem, we are given the total impedance (Z) and the phase angle (ϕ) of a body in terms of resistance (R) and capacitive reactance (Xc) as follows,
Z = √(R² + Xc²) .....(1)
ϕ = tan⁻¹(-Xc/R) ......(2)
Now, we need to calculate the resistance (R) and capacitive reactance (Xc) of the body using the given values of Z and ϕ.In the given problem, we have the following values:
Z = 5.59×10^2° = 559 ωϕ = −7.98°
Now, using the equation (1), we have = √(R² + Xc²)
Substituting the given value of Z in the above equation, we have559 = √(R² + Xc²)
Squaring both sides, we have 559² = R² + Xc²R² + Xc² = 312,481 .....(3)
Now, using the equation (2), we have
ϕ = tan⁻¹(-Xc/R)
Substituting the given values of ϕ and R in the above equation, we have-7.98° = tan⁻¹(-Xc/R)
tan(-7.98°) = -Xc/R
-0.139 = -Xc/R
Xc = 0.139R .....(4)
Substituting the value of Xc from equation (4) into equation (3), we get
R² + (0.139R)² = 312,481
R² + 0.0193
R² = 312,4811.0193
R² = 312,481R² = 306,125.2R = √306,125.2
R = 553.372 Ω
Therefore, the body's resistance (R) is 553.372 Ω.
Substituting this value of R in equation (4), we get
Xc = 0.139 × 553.372Xc = 77.118 Ω
Therefore, the body's capacitive reactance (Xc) is 77.118 Ω.
The answers are:(a) Resistance (R) = 553.372 Ω.(b) Capacitive reactance (Xc) = 77.118 Ω.
To learn about resistance here:
https://brainly.com/question/30901006
#SPJ11
What is the minimum work needed to push a distance d up a ramp at an incline of θ?
The minimum work needed to push a distance d up a ramp at an incline of θ is given by the formula:
`W = mgd * sinθ` Where,
W = Minimum work required
m = Mass of the objectg
d = Vertical displacement
sinθ = Incline (sine of the angle of incline)
The inclined plane is a simple machine that is used to make it easier to lift an object to a certain height. It is used in place of a vertical plane because the amount of force required to lift the object is less. The inclined plane is used to reduce the amount of work required to move an object from one place to another.
Learn more about work https://brainly.com/question/21854305
#SPJ11
How many watts does a flashlight that has 6.4 x 10²C pass through it in 0.492 h use if its voltage is 3 V? __________ W
The power consumed by the flashlight is 10.92 W.
watt = volt x coulombs/sec
where:
watt = power
volt = voltage
coulombs/sec = charge/time
Put the given values in the formula, we get:
watt = 3 V × (6.4 × 10² C/0.492 h)
watt = 3 V × (6.4 × 10² C/1769.2 s)
watt = 10.92 W
Therefore, the power consumed by the flashlight is 10.92 W.
Learn more about power: https://brainly.com/question/11569624
#SPJ11
Thin Lenses: A concave lens will O focalize light rays O reticulate light rays diverge light rays converge light rays
A concave lens will diverge light rays.
A concave lens is a thin lens that is thinner at the center than at the edges. When light rays pass through a concave lens, they are refracted or bent away from the principal axis of the lens. This bending of light causes the light rays to diverge or spread apart.
Unlike a convex lens, which converges light rays to a focal point, a concave lens disperses light rays. The diverging effect of a concave lens is due to the fact that the center of the lens is thinner than the edges, causing the light rays to bend away from each other.
This phenomenon is known as negative or diverging refraction. As a result, parallel light rays passing through a concave lens will spread out and appear to originate from a virtual point on the same side of the lens as the object. This point is called the virtual focal point.
The ability of a concave lens to diverge light rays makes it useful in correcting certain vision problems. For example, concave lenses are commonly used to correct nearsightedness (myopia), where the light rays converge before reaching the retina.
By adding a concave lens in front of the eye, the light rays are spread out, allowing them to focus properly on the retina.
Learn more about lens here ;
https://brainly.com/question/29834071
#SPJ11
Maxwell's Equation
A circular-plates capacitor of radius R = 22.0 cm is connected to a source of
emf E= Emsinωt, where Em = 237V and ω = 180rad/s. The maximum value
of the displacement current is id = 4.5μA.
(a) Find the maximum value of the current i in the circuit.
(b) Find the maximum value of dφE /dt, where φE is the electric flux through the
region between the plates.
(c) Find the separation d between the plates.
(d) Find the maximum value of the magnitude of ~B between the plates at a distance
r = 10.7 cm from the center.
A circular-plates capacitor with a radius of 22.0 cm is connected to a sinusoidal voltage source E = Emsin(ωt). The maximum current i is 4.5 μA. he maximum value of dφ [tex]\frac{E}{dt}[/tex] is 237 V * ω. Magnitude can be obtained using ampere's law.
(a) The maximum value of the current, i, can be determined by equating the displacement current, id, to the rate of change of electric flux, dφ [tex]\frac{E}{dt}[/tex], in the circuit. Since id is given as 4.5 μA, the maximum value of i is also 4.5 μA.
(b) The maximum value of dφ [tex]\frac{E}{dt}[/tex] can be calculated by taking the time derivative of the given emf expression E = Em sin(ωt). The derivative of sin(ωt) is ω cos(ωt). Multiplying this by the maximum value of Em (237 V), we get the maximum value of dφ [tex]\frac{E}{dt}[/tex] as 237 V * ω.
(c) The separation between the plates, d, can be found by rearranging the equation for capacitance, C = ε0 * [tex]\frac{A}{d}[/tex], where ε0 is the permittivity of free space and A is the area of the circular plates (π[tex]R^2[/tex]). Substituting the given values of R (22.0 cm) and the known value of C (from the problem), we can solve for d. d = ε0 * (π * R^2) / C.
(d) To find the maximum value of the magnitude of ~B at a distance r = 10.7 cm from the center, we can use Ampere's law in integral form, ∮ B · dl = μ0 * I_enc, where I_enc is the enclosed current. For a circular plate capacitor, the enclosed current is equal to the displacement current, id. By substituting the given value of id and the known values of μ0 and the circumference of the circular path (2πr), we can calculate the maximum value of ~B. Substituting these values into Ampere's law, we have:
B * (2πr) = μ0 * id
We can rearrange this equation to solve for B:
B = (μ0 * id) / (2πr)
Learn more about Ampere's law here:
https://brainly.com/question/32676356
#SPJ11
A particle with mass 2.1 x 10-3 kg and a charge of 2.4 x 10-8 C has, at a given instant, a velocity of v = (3.9 x 104 m/s)j. Determine the magnitude of the particle's acceleration produced by a uniform magnetic field of B = (1.5 T)i + (0.7 T)i. (include units with answer)
The magnitude of the particle's acceleration is [tex]6.006 * 10^{(-4)}[/tex] N that can be determined using the given values of mass, charge, velocity, and the uniform magnetic field.
For determine the magnitude of the particle's acceleration, the equation use for the magnetic force experienced by a charged particle moving in a magnetic field:
F = q(v x B)
Here, F is the magnetic force, q is the charge of the particle, v is its velocity, and B is the magnetic field. The cross product (v x B) give the direction of the force, which is perpendicular to both v and B.
Given:
Mass of the particle, [tex]m = 2.1 * 10^{(-3)} kg[/tex]
Charge of the particle, [tex]q = 2.4 * 10^{(-8)} C[/tex]
Velocity of the particle,[tex]v = (3.9 * 10^4 m/s)j[/tex]
Uniform magnetic field, B = (1.5 T)i + (0.7 T)i
Substituting the given values into the equation,
[tex]F = (2.4 * 10^{(-8)} C) * ((3.9 * 10^4 m/s)j * ((1.5 T)i + (0.7 T)i))[/tex]
Performing the cross product,
[tex]F = (2.4 * 10^{(-8)} C) * (3.9 * 10^4 m/s) * (0.7 T)[/tex]
Calculating the magnitude of the force,
[tex]|F| = |q(v * B)| = (2.4 * 10^{(-8)} C) * (3.9 * 10^4 m/s) * (0.7 T)\\[/tex]
=[tex]6.006 * 10^{(-4)}[/tex] N
Hence, the magnitude of the particle's acceleration produced by the uniform magnetic field is [tex]6.006 * 10^{(-4)}[/tex] N.
Learn more about magnetic force here:
https://brainly.com/question/30532541
#SPJ11
The smaller disk dropped onto a larger rotating one. (frame rate=30fps. Frames=36)(time 1.2 s). The large disk is made of dense plywood rotating on a low-friction bearing. The masses of the disks are: large disk: 2.85kg Radius of large disk = 0.3m small disk: 3.06 kg Radius of small disk= 0.18m
(1) Make measurements and calculations to determine the final speed of the two disk rotating together, and calculate the percent difference between your predicted value and the experimental value. Hint: The final velocity of the two-disk system should be measured when the two disks reach the same angular velocity. How can you tell when that happens?
(2) Determine the total angular momentum of the two-disk system after the smaller disk is dropped on the larger one. Calculate the percent difference: percent change=((L sys−L sys)/L sys)×100
(3) Determine the total kinetic energy of the two-disk system before and after the collision. Calculate the percent difference between the two values.
(4) Compare the percent change in angular momentum of the system to the percent change in the rotational kinetic energy of the system. Explain the difference between these two values.
The final speed of the two-disk system can be determined by equating the angular momentum before and after the collision. The total angular of the two-disk system after the smaller disk is dropped on the larger one is the sum of the individual angular momenta of the disks.
(1) The angular momentum is given by the product of the moment of inertia and the angular velocity. Since the system is initially at rest, the initial angular momentum is zero. When the two disks reach the same angular velocity, the final angular momentum is given by the sum of the individual angular momenta of the disks. By equating these two values, we can solve for the final angular velocity. The final linear speed can then be calculated by multiplying the final angular velocity with the radius of the combined disks. To determine when the disks have reached the same angular velocity, one can observe their motion visually and note when they appear to be rotating together smoothly.
(2) The angular momentum of a disk is given by the product of its moment of inertia and angular velocity. By adding the angular momenta of the large and small disks, we can calculate the total angular momentum of the system. The percent difference can be calculated by comparing this value to the initial angular momentum, which is zero since the system starts from rest.
(3) The total kinetic energy of the two-disk system before and after the collision can be calculated using the formulas for rotational kinetic energy. The rotational kinetic energy of a disk is given by half the product of its moment of inertia and the square of its angular velocity. By summing the rotational kinetic energies of the large and small disks, we can determine the initial and final kinetic energies of the system. The percent difference can be calculated by comparing these two values.
(4) The percent change in angular momentum of the system and the percent change in the rotational kinetic energy of the system may not be the same. This is because angular momentum depends on both the moment of inertia and the angular velocity, while rotational kinetic energy depends only on the moment of inertia and the square of the angular velocity. Therefore, changes in the angular velocity may not be directly proportional to changes in the rotational kinetic energy. The difference between these two values can arise due to factors such as the redistribution of mass and changes in the system's geometry during the collision.
To know more about angular momentum, click here :
https://brainly.com/question/29897173
#SPJ11
A uniform solid disk of mass m - 3.01 kg and radius r=0.200 m rotates about a fixed axis perpendicular to its face with angular frequency 6.04 rad/s. (a) Calculate the magnitude of the angular momentum of the disk when the axis of rotation passes through its center of mass kg-m²/s (b) What is the magnitude of the angular momentum when the axis of rotation passes through a point midway between the center and the rim? kg-m²/s
A)The magnitude of the angular momentum when the axis of rotation passes through its center of mass is 0.364 kg m²/s and B) when the axis of rotation passes through a point midway between the center and the rim is 0.272 kg m²/s.
(a) Since the axis of rotation passes through the center of mass, we know that the angular velocity of the disk is equal to its linear velocity divided by the radius of the disk: ω=v/r
We know that the mass of the disk is 3.01 kg and its radius is 0.200 m.
Therefore, the moment of inertia of the disk is given by: I=(1/2)mr²=(1/2)(3.01 kg)(0.200 m)²=0.0601 kg m²
The angular momentum of the disk when the axis of rotation passes through its center of mass is given by:
L=Iω=(0.0601 kg m²)(6.04 rad/s)=0.364 kg m²/s
(b) When the axis of rotation passes through a point midway between the center and the rim, we know that the moment of inertia of the disk is given by I=(3/4)mr².
We also know that the angular velocity of the disk is the same as before: ω=v/r, where v is the linear velocity of the disk.
To find the linear velocity of the disk, we need to use conservation of energy. Since there are no external forces acting on the disk, we know that its total energy is conserved.
Therefore, the sum of its kinetic energy (KE) and potential energy (PE) is constant throughout its motion. At the top of its path, all of its potential energy has been converted into kinetic energy, so we can write:
KE=PEmg(2r)=(1/2)mv²where g is the acceleration due to gravity, m is the mass of the disk, r is the radius of the disk, and v is the linear velocity of the disk.
Solving for v, we get:v=√(4gr/3)=√((4)(9.81 m/s²)(0.200 m)/3)=2.34 m/s
Therefore, the angular momentum of the disk when the axis of rotation passes through a point midway between the center and the rim is given by:
L=Iω=(3/4)mr²ω=(3/4)(3.01 kg)(0.200 m)²(6.04 rad/s)=0.272 kg m²/s
Thus, the magnitude of the angular momentum when the axis of rotation passes through its center of mass is 0.364 kg m²/s and when the axis of rotation passes through a point midway between the center and the rim is 0.272 kg m²/s.
Know more about angular velocity here,
https://brainly.com/question/32217742
#SPJ11
Write a discussion and analysis about. the half-wave rectifier ofg the operation
A half-wave rectifier is an electronic circuit that converts the positive half-cycle or the negative half-cycle of an alternating current signal to a pulsating direct current signal. It allows the current to flow in only one direction by removing half of the signal. A half-wave rectifier is less effective than a full-wave rectifier, which utilizes both the positive and negative halves of the AC signal.
The following is a discussion and analysis of the half-wave rectifier operation.
Discussion-
Half-wave rectifiers are frequently used in DC power supply circuits. The fundamental purpose of rectification is to convert AC to DC. Rectifiers may be used to power a variety of electronic devices, ranging from simple battery-powered gadgets to high-voltage power supplies.
During the positive half-cycle of the input AC signal, the diode is forward-biased, allowing current to flow. The load is consequently supplied with a current flow in one direction only. The diode is reverse-biased during the negative half-cycle of the input AC signal, preventing the current from flowing.
The output voltage is unidirectional and has a pulsating nature as a result of this half-wave rectification. It means that, at the beginning of each half-cycle, the output voltage starts from zero and then grows to a peak value until the half-cycle ends.
Analysis:
A half-wave rectifier's output voltage is not pure DC since it contains a lot of ripples. To reduce ripple, an input filter capacitor can be used to smooth the voltage waveform. The resulting waveform is smoothed out and closer to pure DC. As a result, a half-wave rectifier has the following characteristics:
-The maximum voltage is only half the peak input voltage.
-The DC output voltage is pulsating, with a considerable ripple.
-The efficiency of a half-wave rectifier is around 40-50%.
-The half-wave rectifier has a low cost and simple design.
The half-wave rectifier circuit is simple and requires only a single diode. As a result, it is less expensive and more straightforward than a full-wave rectifier circuit. However, the half-wave rectifier has certain disadvantages, such as a considerable amount of ripple and a reduced efficiency of around 40-50%. As a result, it is frequently used in low-power applications.
know more about half-wave rectifier
https://brainly.com/question/32341314
#SPJ11
A parallel beam of monoenergetic photons emerged from a source when the shielding was removed for a short time. The photon energy hv and the total fluence o of photons are known. (a) Write a formula from which one can calculate the absorbed dose in air in rad from hv, expressed in MeV, and p, expressed in cm-². (b) Write a formula for calculating the exposure in R.
(a) Formula from which one can calculate the absorbed dose in the air in rad from hv, expressed in MeV, and p is [tex]D = (0.877 * o * hv) / p[/tex]. (b) the formula for calculating the exposure in R is [tex]X = (0.87 * o *hv)[/tex].
(a)These formulas allow for the calculation of radiation effects in different units. To calculate the absorbed dose in the air in rad (D), expressed in MeV and cm², the formula can be written as:
[tex]D = (0.877 * o * hv) / p[/tex]
Where o represents the total fluence of photons and hv represents the energy of photons in MeV. p is the area in [tex]cm^2[/tex] over which the radiation is spread.
(b)For calculating the exposure in R (X), the formula can be expressed as:
[tex]X = (0.87 * o *hv)[/tex]
Again, o represents the total fluence of photons and hv represents the energy of photons in MeV.
These formulas provide a means to quantify the absorbed dose and exposure to radiation in the air, allowing for a better understanding and assessment of radiation effects.
learn more about absorbed dose here:
https://brainly.com/question/30512352
#SPJ11
A pulley, with a rotational inertia of 2.4 x 10⁻² kg.m² about its axle and a radius of 11 cm, is acted on by a force applied tangentially at its rim. The force magnitude varies in time as F = 0.60t+ 0.30t², with F in newtons and t in seconds. The pulley is initially at rest. At t = 4.9 s what are (a) its angular acceleration and (b) its angular speed?
Answer: The angular acceleration of the pulley is 10.201 rad/s²
The angular speed of the pulley is 49.98 rad/s.
(a) The angular acceleration of the pulley can be determined as; The formula for torque is;
τ = Iα
Where τ = force × radius
= F × r = (0.60t + 0.30t²) × 0.11
= 0.066t + 0.033t².
Substitute the given values of I and τ in the above expression,
2.4 × 10⁻² × α
= 0.066t + 0.033t²α
= (0.066t + 0.033t²)/2.4 × 10⁻²α
= (0.066 × 4.9 + 0.033 × (4.9)²)/(2.4 × 10⁻²)α
= 10.201 rad/s².
Therefore, the angular acceleration of the pulley is 10.201 rad/s²
(b) The angular speed of the pulley can be determined as;
ω = ω₀ + αt
Where ω₀ = 0 (as the pulley is initially at rest). Substitute the given values in the above expression,
ω = αt
ω = 10.201 × 4.9
ω = 49.98 rad/s.
Therefore, the angular speed of the pulley is 49.98 rad/s.
Learn more about angular speed : https://brainly.com/question/6860269
#SPJ11
An electron is in a particle accelerator. The electron moves in a straight line from one end of the accelerator to the other, a distance of 2.08 km. The electron's total energy is 17.0 GeV. The rest energy of an electron is 0.511 Mev. (a) Find the y factor associated with the energy of the electron (b) Imagine an observer moving along with the electron at the same speed. How long does the accelerator appear to the moving observer? (Express your answer in units of meters.) m
An electron is in a particle accelerator The electron moves in a straight line from one end of the accelerator to the other, a distance of 2.08 km. The electron's total energy is 17.0 GeV. The rest energy of an electron is 0.511 Mev. (a)The Lorentz factor (γ) associated with the energy of the electron is approximately 33,307.03.(b)The accelerator appears to the moving observer to be approximately 0.0625 meters long.
(a) To find the y factor associated with the energy of the electron, we can use the relativistic energy equation:
E = γmc^2
where:
E is the total energy of the electron,
γ is the Lorentz factor (also denoted as γ = 1/√(1 - (v^2/c^2))),
m is the rest mass of the electron, and
c is the speed of light in a vacuum.
Given:
E = 17.0 GeV = 17.0 × 10^9 eV (converting GeV to eV),
m = 0.511 MeV = 0.511 × 10^6 eV (converting MeV to eV).
To calculate γ, we rearrange the equation:
γ = E / (mc^2)
γ = (17.0 × 10^9 eV) / (0.511 × 10^6 eV)
≈ 33,307.03
Therefore, the Lorentz factor (γ) associated with the energy of the electron is approximately 33,307.03.
(b) If an observer moves along with the electron at the same speed, the observer's frame of reference is in the rest frame of the electron. In this frame, the distance traveled by the electron is the proper length. The proper length (L') can be calculated using the Lorentz contraction formula:
L' = L / γ
where:
L' is the proper length (distance measured in the electron's rest frame),
L is the distance observed by the moving observer (2.08 km), and
γ is the Lorentz factor.
Plugging in the values:
L' = (2.08 km) / γ
= (2.08 × 10^3 m) / 33,307.03
≈ 0.0625 m
Therefore, the accelerator appears to the moving observer to be approximately 0.0625 meters long.
To learn more about particle accelerator visit: https://brainly.com/question/2531035
#SPJ11
if electromagnetic radiation has a wavelength of 9 x 10^4m, then the period of this electromagnetic radiation expressed in scientific notation is a.bc x 10^d. What are a,b,c, and d?
The period of electromagnetic radiation with a wavelength of 9 x 10^4m is 1.11 x 10^-2s.
The period of a wave is the time it takes for one complete cycle or oscillation. It is related to the wavelength (λ) by the equation:
v = λ/T
where v is the velocity of the wave. In the case of electromagnetic radiation, the velocity is the speed of light (c), which is approximately 3 x 10^8 m/s.
Rearranging the equation, we have:
T = λ/v
Plugging in the values given, we get:
T = (9 x 10^4 m) / (3 x 10^8 m/s)
To simplify the expression, we can divide both the numerator and denominator by 10^4:
T = (9/10^4) x (10^4/3) x 10^4
Simplifying further, we have:
T = 3/10 x 10^4
This can be written in scientific notation as:
T = 0.3 x 10^4
Finally, we can rewrite 0.3 as 1.11 x 10^-2 by moving the decimal point one place to the left, resulting in the answer:
T = 1.11 x 10^-2 s
Therefore, the period of the electromagnetic radiation is 1.11 x 10^-2 seconds.
Learn more about electromagnetic radiation here:
https://brainly.com/question/29646884
#SPJ11
For the following six questions, match the descriptions to the below people (A-J)
A) Eratosthenes B) Aristarchus C) Isaac Newton D) Aristotle E) Ptolemy F) Galileo G) Hipparchus H) Kepler I) Nicolaus Copernicus J) Tycho Brahe
23. Discovered the phases of Venus using a telescope.
24. First to consider ellipses as orbits.
25. Foremost ancient Greek philosopher.
26. Ancient Greek who believed in a sun-centered universe.
27. First to measure the size of the Earth to good accuracy.
28. Developed the first predictive model of the solar system.
The correct match of the descriptions to the below people are 23 - F, 24 - H, 25 - D, 26 - I, 27 - A, 28 - B.
23 - F Galileo: Galileo Galilei is credited with discovering the phases of Venus using a telescope. Through his observations, he observed that Venus went through a series of phases similar to those of the Moon, which supported the heliocentric model of the solar system.
24 - H Kepler: Johannes Kepler was the first to consider ellipses as orbits. He formulated the laws of planetary motion, known as Kepler's laws, which stated that planets move in elliptical paths with the Sun at one of the foci. Kepler's work revolutionized our understanding of celestial mechanics.
25 - D Aristotle: Aristotle, the ancient Greek philosopher, is considered one of the foremost thinkers in history. While his contributions span various fields, including philosophy and natural sciences, his views on astronomy were geocentric. He believed that the Earth was the center of the universe and that celestial bodies moved in perfect circles around it.
26 - I Nicolaus Copernicus: Nicolaus Copernicus was an astronomer who proposed the heliocentric model of the solar system, in which the Sun, rather than the Earth, was at the center. Copernicus's revolutionary idea challenged the prevailing geocentric view and laid the foundation for modern astronomy.
27 - A Eratosthenes: Eratosthenes was an ancient Greek mathematician and astronomer who made significant contributions to geography and astronomy. He is known for his accurate measurement of the Earth's circumference. By measuring the angle of the Sun's rays at two different locations, he estimated the Earth's circumference with remarkable accuracy.
28 - B Aristarchus: Aristarchus of Samos is credited with developing the first predictive model of the solar system. He proposed a heliocentric model centuries before Copernicus, suggesting that the Sun was at the center of the universe, with the Earth and other planets orbiting it. Aristarchus's model was a significant departure from the prevalent geocentric view of the time.
To know more about people here
https://brainly.com/question/1581614
#SPJ4
and a and b are constants. male e for 1844) antive 1) anthor-op 2. Consider two infinite parallel plates at a = 0 and x = d.The space between them is filled by a gas of electrons of a density n = ng sinan. where o is a constant (12pts) (a) find the potential between the plates that satisfy the conditions (0) = 0 and 6 (0) (b) find the electric field E and then the points where it vanishes, (c) find the energy needed to transport a particle of charge go from the lower plate at I = 0 to the point at x = 7/a
The potential difference Δφ between the plates is zero. The electric field E between the plates is also zero. This implies that the electric field vanishes everywhere between the plates.
To solve this problem, we'll follow the given steps:
(a) Find the potential between the plates that satisfy the conditions φ(0) = 0 and φ(d) = 0.
The electric field E is given by E = -dφ/dx. Since E is constant between the plates, we have E = Δφ/d, where Δφ is the potential difference between the plates and d is the distance between them.
Using the formula for electric field E = -dφ/dx, we can integrate it to obtain:
∫dφ = -∫E dx
φ(x) = -E(x - 0) + C
Given that φ(0) = 0, we can substitute these values to find the constant C:
0 = -E(0 - 0) + C
C = 0
Therefore, the potential φ(x) between the plates is given by φ(x) = -Ex.
Now, we need to find the potential difference Δφ between the plates, which satisfies φ(d) = 0:
0 = -Ed
Δφ = φ(d) - φ(0) = 0 - 0 = 0
Therefore, the potential difference Δφ between the plates is zero.
(b) Find the electric field E and then the points where it vanishes.
Since the potential difference Δφ is zero, the electric field E between the plates is also zero. This implies that the electric field vanishes everywhere between the plates.
(c) Find the energy needed to transport a particle of charge q from the lower plate at x = 0 to the point at x = 7/a.
The energy needed to transport a charged particle is given by the work done against the electric field. In this case, since the electric field E is zero, the energy required to transport the particle is zero.
Therefore, the energy needed to transport a particle of charge q from the lower plate at x = 0 to the point at x = 7/a is zero.
Learn more about energy here ;
https://brainly.com/question/1932868
#SPJ11
Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 1.6% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of of galaxy relative to the earth? Vrel = Number ________________ Units ____________
The speed vrel of the galaxy relative to the Earth is 4.8 x 10^6 m/s
Number = 4.8 x 10^6; Units = m/s.
In order to calculate the speed vrel of the galaxy relative to the Earth, we can use the formula:
vrel/c = Δf/f
where
c is the speed of light,
Δf is the change in frequency, and
f is the frequency emitted by the source in the distant galaxy.
So, first we need to calculate the value of Δf.
We know that the frequency observed on Earth is 1.6% greater than the frequency emitted by the source in the distant galaxy.
Mathematically, we can express this as:
Δf = (1.6/100) x f
where f is the frequency emitted by the source in the distant galaxy.
Substituting this value of Δf in the above formula, we get:
vrel/c = Δf/f
= (1.6/100) x f / f
= 1.6/100
vrel/c = 0.016
vrel = c x 0.016
vrel = 3 x 10^8 m/s x 0.016
= 4.8 x 10^6 m/s
Hence, the speed vrel of the galaxy relative to the Earth is 4.8 x 10^6 m/s (meters per second).
Number = 4.8 x 10^6; Units = m/s.
Learn more about the speed vrel:
brainly.com/question/15417626
#SPJ11
In cases of Refraction, when the refracted beam approaches the Normal when passing the medium, it is due to:
A) the refractive index is lower because the material is less dense
B) The wavelength changes but the frequency remains constant.
C) The refractive index increases because it is denser.
D) The medium where light refracts absorbs energy.
Correct option is C. When the refracted beam approaches the Normal when passing through a medium, it is due to the increased refractive index of the denser material.
Refraction is the bending of light as it passes from one medium to another with a different refractive index. The refractive index is a measure of how much a medium can bend light. When a beam of light travels from a less dense medium to a denser medium, such as from air to water or from air to glass, the beam of light bends towards the normal (an imaginary line perpendicular to the surface of the medium).
The change in direction of the light beam occurs because the speed of light is different in different materials. The refractive index is defined as the ratio of the speed of light in a vacuum to the speed of light in the medium. When light enters a denser medium, such as water or glass, its speed decreases, resulting in a higher refractive index for the medium. As a result, the beam of light bends towards the normal.
Therefore, the correct answer is C) The refractive index increases because it is denser.
Learn more about refractive index here:
https://brainly.com/question/30761100
#SPJ11
A 0.26-kg rock is thrown vertically upward from the top of a cliff that is 32 m high. When it hits the ground at the base of the cliff, the rock has a speed of 29 m>s. Assuming that air resistance can be ignored, find (a) the initial speed of the rock and (b) the greatest height of the rock as measured from the base of the cliff.
The initial speed of the rock is 14.6 m/s and the greatest height of the rock as measured from the base of the cliff is 30.08 m.
Using the law of conservation of energy, the initial kinetic energy of the rock is equal to its potential energy at the top of the cliff, plus the work done against gravity while it is thrown upwards.
Kinetic energy,[tex]KE = 1/2 mv^{2}[/tex] Potential energy, PE = mgh
Work done against gravity, W = mgh
So, [tex]1/2 mv^{2} = mgh + mgh1/2 v^{2} = 2ghv^{2} = 4gh[/tex]
Initial velocity,[tex]u = \sqrt{(v^{2} - 2gh)u} = \sqrt{(29^{2} - 2 $\times$9.8 $\times$ 32)u} = \sqrt{(841 - 627.2)u } = \sqrt{213.8u } = 14.6 m/s[/tex]
Therefore, the initial speed of the rock is 14.6 m/s.
The greatest height of the rock can be found using the equation: [tex]v^{2} = u^{2} - 2gh[/tex] where u is the initial velocity of the rock, v is its velocity at the highest point and h is the maximum height reached by the rock.
At the highest point, v = 0.
So, [tex]0^{2} = (14.6)^{2} - 2gh, h = (14.6)^{2} / 2g h = 30.08 m[/tex]
Therefore, the greatest height of the rock as measured from the base of the cliff is 30.08 m.
For more questions on initial speed
https://brainly.com/question/24493758
#SPJ8
A block is released from rest at a vertical height H above the base of a frictionless ramp. After sliding off the ramp, the block encounters a rough, horizontal surface and comes to a stop after moving a distance 2H. What is the coefficient of kinetic friction between the block and the horizontal surface?
The coefficient of kinetic friction between the block and the vertical face is H/ 2H or1/2.
In the given question, a block is released from rest at a perpendicular height H above the base of a amicable ramp. After sliding off the ramp, the block encounters a rough, vertical face and comes to a stop after moving a distance 2H. We need to find the measure of kinetic disunion between the block and the vertical face. Let's denote the coefficient of kinetic friction by' µ'. The distance moved by the block is 2H. The final haste of the block is 0 m/ s as the block comes to a stop. Now, we know that the work done by friction is equal to the kinetic energy lost by the block. W = change in KE.
This implies the following relation
Frictional force x Distance moved by the block = (1/2) m( vf ²- vi ²)
We can calculate the original haste of the block when it slides off the ramp using the conservation of energy.
Total energy at the top = Implicit energy at the top mgh = (1/2) mv ² v = sqrt( 2gh) So, original haste, vi = sqrt( 2gh)
The final haste of the block, vf = 0 m/ s
The distance moved by the block, d = 2H
From the below relation, we can write µmgd = (1/2) m( vf ²- vi ²) µgd = (1/2) v ² µgd = (1/2)( sqrt( 2gh)) ² µgd = gh µ = h/ d = H/ 2H = 1/2
The coefficient of kinetic friction between the block and the vertical face is H/ 2H or1/2.
Learn more about kinetic friction https://brainly.com/question/14111192
#SPJ11
What is the smallest thickness of a soap bubble (n=1.33) capable of producing reflective constructive 568nm light ray?
The smallest thickness of a soap bubble capable of producing reflective constructive interference for a 568 nm light ray is approximately 213.53 nanometers.
To determine the smallest thickness of a soap bubble that can produce reflective constructive interference for a specific wavelength of light, we can use the equation for constructive interference in a thin film:
2t = mλ/n
where:
t is the thickness of the soap bubble
m is the order of the interference (in this case, m = 1 for first-order)
λ is the wavelength of the light
n is the refractive index of the medium (in this case, the refractive index of the soap bubble, n = 1.33)
Rearranging the equation, we get:
t = (mλ)/(2n)
Plugging in the values, we have:
t = (1 x 568 nm) / (2 x 1.33)
Calculating this, we find:
t ≈ 213.53 nm
Therefore, the smallest thickness of a soap bubble capable of producing reflective constructive interference for a 568 nm light ray is approximately 213.53 nanometers.
Learn more about constructive interference
https://brainly.com/question/32710335
#SPJ11
write the missing words in each of the following 1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area equal to ..... 2. The formula of the work done (W) is: .......... 3. The relation between the electric field (E) and the electric potential (V) is ..... 4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by 5. The charge (Q) stored in a capacitor can be given by..... 6. The product of the resistance of a conductor (R) and the current passing through it (I) is 7. The unit of the magnetic flux density is..... 8. A region in which many atoms have their magnetic field aligned is called a
The unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area is equal to 90 degrees.2. The formula of the work done (W) is: W = F × d × cos(θ), where F is the force, d is the displacement, and θ is the angle between the force and displacement.3. The relation between the electric field (E) and the electric potential (V) is E = -dV/dx, where dx is the distance between the points where the potential is measured.
4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by C = εA/d, where ε is the permittivity of the medium between the plates.5. The charge (Q) stored in a capacitor can be given by Q = CV, where C is the capacitance and V is the potential difference between the plates.
6. The product of the resistance of a conductor (R) and the current passing through it (I) is P = VI, where P is the power dissipated by the conductor.7. The unit of the magnetic flux density is tesla (T).8. A region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a conclusion:In conclusion, the maximum value of electric flux is attained when the uniform electric field (E) and the surface normal of the area are 90 degrees apart.
Additionally, the formula of the work done (W) is W = F × d × cos(θ), and the capacitance of a parallel plate capacitor is given by C = εA/d. The relationship between the electric field (E) and the electric potential (V) is E = -dV/dx, and the charge (Q) stored in a capacitor can be given by Q = CV.
Finally, the unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
Learn more about electric here,
https://brainly.com/question/14306881
#SPJ11
What is the internal resistance of an automobile battery that has an emf of 12.0 V and a terminal voltage of 18.2 V while a current of 4.20 A is charging it? Ω
The internal resistance of the automobile battery is approximately 1.476 Ω.
To find the internal resistance (r) of the automobile battery, we can use Ohm's Law and the concept of terminal voltage.
Ohm's Law states that the terminal voltage (Vt) of a battery is equal to the electromotive force (emf) of the battery minus the voltage drop across its internal resistance (Vr). Mathematically, it can be expressed as:
Vt = emf - Vr
In this case, we are given:
emf = 12.0 V
Vt = 18.2 V
I = 4.20 A
Rearranging the equation, we can solve for the internal resistance (r):
Vr = emf - Vt
r = Vr / I
Substituting the given values:
Vr = 12.0 V - 18.2 V = -6.2 V (Note: the negative sign indicates a voltage drop)
I = 4.20 A
Calculating the internal resistance:
r = (-6.2 V) / 4.20 A
r ≈ -1.476 Ω
The negative sign indicates that the internal resistance is in the opposite direction of the current flow. However, in this context, we take the magnitude of the resistance, so the internal resistance of the automobile battery is approximately 1.476 Ω.
Learn more about Ohm's Law
https://brainly.com/question/1247379
#SPJ11
what is the electric potential 10cm from a -10nC charge?
The electric potential 10 cm from a -10 nC charge is approximately -9,000 volts.
The electric potential at a point in space due to a point charge can be calculated using the formula V = k * q / r, where V is the electric potential, k is the Coulomb's constant (approximately 8.99 × 10⁹ N m²/C²), q is the charge, and r is the distance from the charge. In this case, the charge is -10 nC (-10 × 10⁻⁹ C) and the distance is 10 cm (0.1 m). Plugging these values into the formula, we get V = (8.99 × 10⁹ N m²/C²) * (-10 × 10⁻⁹ C) / (0.1 m). Simplifying this expression, we find that V is approximately -9,000 volts.
Therefore, the electric potential 10 cm away from a -10 nC charge is approximately -9,000 volts. This negative value indicates that the electric potential is negative, which means that the charge creates an attractive force on positive charges placed at that point. The electric potential decreases as the distance from the charge increases, and in this case, it is a large negative value due to the relatively small distance.
Learn more about electric potential visit:
brainly.com/question/28444459
#SPJ11
The switch opens at t = 0 after a very long time. Find v(t) for t > 0. Draw circuits clearly for each step using 4-step approach to illustrate the situation when t<0 and t>0 when doing circuit analysis for full credit. Write final answers in the box provided. [10 pts] 6 V 30 k 0 47 (1) 60 k 5 μF 60 k
The voltage of switch function v(t) for t > 0 is approximately 5.992 V. The 5 μF capacitor does not affect the voltage at steady-state.
To analyze the circuit and find the voltage function v(t) for t > 0, let's go through the 4-step approach and consider the circuit at t < 0 and t > 0 separately.
Step 1: Circuit at t < 0 (before the switch opens)
At t < 0, the switch is closed, and the capacitor is assumed to have been charged to a steady-state. In this case, the capacitor behaves like an open circuit, and the 60 kΩ resistor is effectively disconnected.
The circuit at t < 0 can be represented as follows:
Step 2: Circuit at t = 0 (when the switch opens)
At t = 0, the switch opens. The capacitor retains its voltage, and the voltage across it remains constant. However, the circuit topology changes as the capacitor now acts as a voltage source with an initial voltage of 6 V.
The circuit at t = 0 can be represented as follows:
Step 3: Circuit at t > 0 (after the switch opens)
At t > 0, the switch remains open, and the circuit reaches a new steady-state. The capacitor acts like an open circuit in the steady-state, and the 60 kΩ resistor is effectively disconnected.
The circuit at t > 0 can be represented as follows:
Step 4: Solving for v(t) for t > 0
To find the voltage function v(t) for t > 0, we can use the voltage divider rule to determine the voltage across the 30 kΩ resistor.
The voltage across the 30 kΩ resistor is given by:
v(t) = (30 kΩ / (30 kΩ + 47 Ω)) * 6 V
Simplifying the equation:
v(t) = (30000 / 30047) * 6 V
v(t) ≈ 5.992 V (approximately)
Therefore, the voltage function v(t) for t > 0 is approximately 5.992 V.
To know more about switch click here:
https://brainly.com/question/33623724
#SPJ11