The focal length of the lens, in which the image is formed on the opposite side of the object- 68.3cm away from it, is -68.5cm.
The formula for finding the focal length of a lens is:
1/f = 1/di + 1/do
where f is the focal length of the lens, di is the distance from the lens to the image and do is the distance from the lens to the object.
In this case, di = -68.3 cm (since the image is formed on the opposite side of the lens), and do = 27.2 cm. Plugging these values into the formula gives:
1/f = 1/-68.3 + 1/27.2
Simplifying this equation gives:
1/f = -0.0146
Multiplying both sides by -1 gives:
-1/f = 0.0146
Dividing both sides by 0.0146 gives:
f ≈ -68.5 cm
The negative sign indicates that the lens is a diverging lens rather than a converging one. If you want to find the focal length of a converging lens, you should get a positive value for f.
To know more about focal length, refer:
https://brainly.com/question/26550490
#SPJ4
why did we calculate the difference between segments rather than simply reporting the point-to-twitch velocities?
The reason why we calculate the difference between segments rather than simply reporting the point-to-twitch velocities is that the point-to-twitch velocities change from one segment to the next due to the effect of inertial forces.
A segment is part of a trajectory between two key points of interest. Point-to-twitch is a measure of the speed of movement between successive key positions. Velocity is the rate at which an object changes its position. It is a vector quantity that has a magnitude (speed) and a direction. It is also known as the rate of change of displacement. We need to calculate the difference between segments because the movement speed is not constant during a movement. The point-to-twitch velocities change from one segment to the next because of the impact of inertial forces. The inertial forces play a crucial role in influencing the velocity of the system. Inertial forces act in a direction opposite to the acceleration of the system.
Learn more about velocities at:
https://brainly.com/question/4931057
#SPJ11
Suppose a wheel is initially rotating at 10.0 rad/s while undergoing constant angular acceleration reaching a speed of 30.0 rad/s after 20.0 seconds have elapsed. How long after the initial time has the wheel undergone half of the angular displacement that it will have gone through during the entire 20.0 second interval?
a. 10.0 s
b. 12.4 s
c. 14.2 s
d. 15.0 s
The answer is B, according to the textbook but I don't know why
To solve this problem, you can use the equations of motion for rotational motion under constant acceleration:
ωf = ωi + αt --(1)
θ = ωit + 0.5αt^2 --(2)
where ωi is the initial angular velocity, ωf is the final angular velocity, α is the angular acceleration, t is the time elapsed, and θ is the angular displacement.
Using equation (1), we can find the angular acceleration of the wheel:
α = (ωf - ωi)/t
= (30.0 rad/s - 10.0 rad/s)/20.0 s
= 1.0 rad/s^2
Using equation (2), we can find the total angular displacement of the wheel during the 20.0 seconds:
θ = ωit + 0.5αt^2
= 10.0 rad/s × 20.0 s + 0.5 × 1.0 rad/s^2 × (20.0 s)^2
= 400.0 rad
To find the time at which the wheel has undergone half of this angular displacement, we can use equation (2) again:
θ/2 = ωit + 0.5αt^2
Rearranging and solving for t, we get:
t = [(-ωi) ± sqrt(ωi^2 + 2αθ)]/α
Since we are looking for a positive time, we take the positive root:
t = [(-10.0 rad/s) ± sqrt((10.0 rad/s)^2 + 2 × 1.0 rad/s^2 × 400.0 rad)]/1.0 rad/s^2
≈ 12.4 s
Therefore, the answer is B, 12.4 s.
The mass of an empty density bottle is 20 grams. Its mass when filled with water is 40.0 grams and 50.0 grams when filled with liquid X. Given that the density of water is 1000 kg/m^3? calculate:
a) The volume of the bottle
b) The density of liquid X
The difference between the bottle's empty and full masses after being filled with water. Hence, the bottle's volume is [tex]20.0 cm^3.[/tex]
How can you figure out a density bottle's capacity?Any bottle with a defined volume that can be weighed both empty and full of the liquid whose density you want to find out is referred to as a density bottle. Thus, you can calculate density using the formula density = mass/volume. Q.
Mass of water = 40.0 g - 20 g
= 20.0 g
The density of water is
[tex]1000 kg/m^3 = 1 g/cm^3[/tex]
Volume of water = Mass of water / Density of water = [tex]20.0 g / 1 g/cm^3 = 20.0 cm^3[/tex]
To know more about masses visit:-
https://brainly.com/question/30337818
#SPJ1
to make real ice cream, how much milk fat must the ice cream contain?
To make real ice cream, the ice cream must contain a minimum of 10% milk fat.
Ice cream is a delicious and popular dessert enjoyed by people all over the world. It is made by mixing cream, sugar, and other ingredients and then freezing the mixture until it becomes thick and creamy. Ice cream is defined as a frozen food product that is made from a mixture of milk, cream, sugar, and flavorings.
It must contain at least 10% milk fat to be considered real ice cream. The milk fat is what gives ice cream its creamy texture and rich flavor. Milk fat is an essential ingredient in ice cream because it gives it the smooth, creamy texture that people love. Without enough milk fat, the ice cream will be thin, icy, and not as flavorful.
Milk fat is a key ingredient in ice cream and is what gives it its signature taste and texture. Most ice cream makers use a combination of milk and cream to achieve the desired milk fat content. Some ice cream makers also add other ingredients like eggs or stabilizers to help improve the texture and consistency of the ice cream.
Ice cream is a popular dessert that has been enjoyed for centuries. By following the proper recipe and using high-quality ingredients like milk fat, you can make delicious and creamy ice cream at home.
To know more about milk fat refer here:
https://brainly.com/question/19589850#
#SPJ11
Label which image below shows the left knee, and which image shows the right knee.
IS
Find the components to write this
vector in unit vector notation:
BR
12.0
45.0⁰
B = [? ]î+ [? ]
The vector BR in unit vector notation is:
BR = 8.485 î + 8.485 j
What is Vector?
Vectors can be added together to find the result, which is known as the vector sum. The vector sum can be found using the head-to-tail method, where the tail of one vector is placed at the head of the other vector. The vector sum is the vector that goes from the tail of the first vector to the head of the second vector.
To write the vector BR in unit vector notation, we need to find its components in the i and j directions.
Given that the magnitude of the vector is 12.0 and it makes an angle of 45 degrees with the positive x-axis, we can use trigonometry to find the components.
The x-component (i-direction) of the vector is given by:
Bx = B cos θ = 12.0 cos 45° = 8.485
The y-component (j-direction) of the vector is given by:
By = B sin θ = 12.0 sin 45° = 8.485
Learn more about Vector from the given link
https://brainly.com/question/27854247
#SPJ1
a series rl circuit with a resistor of 50ohm and inductor of 10mh is connected to a 100v (peak), voltage source. what is the power factor of this circuit? ( the frequency of the input is 250hz)
In this case, the series RL circuit is fairly efficient, as the power factor is close to 1.
The given series RL circuit contains a resistor of 50 Ω and an inductor of 10 mH. It is connected to a 100 V (peak) voltage source. The frequency of the input is 250 Hz. We need to find the power factor of this circuit.
The first step is to find the impedance (Z) of the circuit. The impedance of a series RL circuit is given by:
Z = √(R² + Xl²)
Where R is the resistance and Xl is the inductive reactance.
The formula for inductive reactance is:
Xl = 2πfL
Where f is the frequency and L is the inductance.
Substituting the given values, we get:
Xl = 2π × 250 × [tex]10^{-3}[/tex] = 1.57 ΩZ = √(50² + 1.57²) = 50.18 Ω
Now,
The power factor (PF) of a circuit is given by:
PF = cosφ
Where φ is the phase angle between the voltage and current.
Since this is a series RL circuit, the current lags the voltage by an angle φ, which is given by:
tanφ = Xl/Rφ = [tex]tan^{-1}[/tex](Xl/R)φ = [tex]tan^{-1}[/tex](1.57/50) = 1.79°
The power factor is:
PF = cos(1.79°) = 0.9985 (approx)
Therefore, the power factor of the given series RL circuit is approximately 0.9985.
For more such questions on Power factor.
https://brainly.com/question/31201010#
#SPJ11
if two different wires having identical cross-sectional areas carry the same current, will the drift velocity be higher or lower in the better conductor? explain in terms of the equation vd
When two different wires with identical cross-sectional areas carry the same current, the drift velocity will be lower in the better conductor.
To understand this, let's look at the drift velocity equation:
vd = I / (nAe)
In this equation, vd represents the drift velocity,
I is the current,
n is the number density of free electrons,
A is the cross-sectional area, and e is the charge of an electron.
Since the wires have the same cross-sectional areas (A)
and carry the same current (I),
we can focus on the number density of free electrons (n).
A better conductor has a higher number density of free electrons, meaning there are more free electrons available to carry the charge.
This is one of the main factors contributing to the increased conductivity of the better conductor.
Now, let's examine the equation again.
If n is higher in the better conductor, then the value of the fraction I / (nAe) will be smaller.
This means that the drift velocity (vd) will be lower in the better conductor.
In summary, the drift velocity is lower in the better conductor due to its higher number density of free electrons, which allows for more efficient charge transfer without the need for high drift velocities.
For similar question on velocity.
https://brainly.com/question/25749514
#SPJ11
if the force on a particle at some point in space is zero, must its potential energy also be zero at that point? match the words in the left column to the appropriate blanks in the sentences on the right.
If the net force on a particle at some point in space is zero, its potential energy need not be zero at that point.
According to the law of energy conservation, a particle's mechanical energy is conserved, i.e., it is constant when there is no external force. So, the net force on a particle is zero when the potential energy is maximum or minimum at that point. This statement means that the particle's mechanical energy is the sum of its potential energy and kinetic energy, and it is constant.
To understand it better, let us consider an example of a block of mass m, which is sliding down a frictionless hill. Here, the particle has the highest potential energy at the top of the hill and zero potential energy at the bottom of the hill. According to the law of conservation of energy, the total mechanical energy of the block at the top of the hill is equal to the total mechanical energy of the block at the bottom of the hill.
So, if the net force on a particle at some point in space is zero, its potential energy need not be zero at that point. The potential energy can be either maximum or minimum, and the particle's mechanical energy is constant.
Note: The question is incomplete. The complete question probably is: If the net force on a particle at some point in space is zero, must its potential energy also be zero at that point? Explain.
Learn more about Potential energy:
https://brainly.com/question/24933254
#SPJ11
the speed of light is . how long does it take light to travel ? set the math up. but don't do any of it. just leave your answer as a math expression.
The mathematical expression for calculating the time taken by light to travel a distance is
`time = distance / 299,792,458`.
As a question-answering bot, I understand the prompt, "The speed of light is __.
How long does it take light to travel : Set the math up.
But don't do any of it.
Just leave your answer as a math expression.
The prompt is asking to set up the mathematical expression for calculating the time taken by light to travel a particular distance.
The speed of light is 299,792,458 meters per second (m/s).
The time taken by light to travel a distance is calculated by the formula `time = distance / speed of light`.
Therefore, the mathematical expression for calculating the time taken by light to travel a distance can be set up as `time = distance / 299,792,458`.
Here, the unit of distance is meters and the unit of speed of light is meters per second.
The unit of time is seconds.
Therefore, the unit of the expression `time = distance / 299,792,458` is seconds.
This mathematical expression can be used to calculate the time taken by light to travel a particular distance.
For example, if the distance is 10 meters, then the time taken by light to travel the distance can be calculated as
`time = 10 / 299,792,458 seconds`.
This simplifies to `time = 3.3356409519815205 × [tex]10^-8[/tex] seconds`.
For similar question on expression.
https://brainly.com/question/25968875
#SPJ11
The charge on A is +6,4
The charge on B is 24,6
Express each charge in Coulombs using scientific notation
The charge on A is +10.24x10-19 Coulombs and the charge on B is 39.36x10-19 Coulombs.
Describe Coulomb's Law. Coulomb's law states that the force of attraction or repulsion between two charged bodies is inversely proportional to the square of the distance between them and directly proportional to the product of their charges.
Charge of an electron is =0.00000000000000000016
=10000000000000000000016
=102016
=10201.6×10
=10191.6
=1.6×10−19
so the charge on A is +6.4x 1.6x10-19 , 10.24x10-19Coulombs
similarly,
The charge on B is 24,6x1.6x10-19 , 39.36x10-19 Coulombs
To know more about Coulomb's Law, click the below link
https://brainly.com/question/506926
#SPJ4
What variable affects the natural frequency of an organ pipe?A) Pipe WidthB) Pipe lengthC) Pipe areaD) Pipe use
The resonance frequency relies simply on the length of both the organ pipe. The right answer is (c), which states that the frequency of the open organ pipe is 300 Hz.
Why does natural frequency change?
The object's content, size, construction, weight, and form all affect the natural frequency measurement. If we exert a vibrating force on the item that possesses a frequency equal to the inherent frequency of the material, it is a resonance situation.
What impact does a pipe's length have on frequency?
The diameter of the tube should not matter because lengthening the tube reduces frequency. According to a more detailed prediction, the diameter does have a minor effect by mildly raising the actual length of the conduit as the diameter expands.
To know more about force click here
brainly.com/question/30563158
#SPJ4
When ultraviolet light with a wavelength of 400.0 nm falls on a certain metal surface, the maximum kinetic energy of the emitted photoelectrons is measured to be 1.10 eV. What is the maximum kinetic energy of the photoelectrons when light of wavelength 300.0 nm falls on the same surface?
The maximum kinetic energy of the photoelectrons when light of wavelength 300.0 nm falls on the same surface is 1.83 eV.
The maximum kinetic energy of the photoelectrons when light of wavelength 300.0 nm falls on the same surface is 1.83 eV.Step-by-step explanation:
Given, The wavelength of light, λ₁ = 400.0 nm.
The maximum kinetic energy of the emitted photoelectrons, K₁ = 1.10 eV. We need to find the maximum kinetic energy of the photoelectrons when light of wavelength 300.0 nm falls on the same surface.
We know that the maximum kinetic energy of the photoelectrons is given byK.E = (hc/λ) - Φwherehc = 4.14 x 10⁻¹⁵ eV s.
Planck's constant = 6.63 x 10⁻³⁴ JsΦ = work function of the metal surface.
The work function of the metal surface is the energy required to remove an electron from the metal surface. It is the minimum energy required to emit an electron from the surface of the metal.
For metals, it lies between 2 eV and 6 eV. We can write K. E₁ = (hc/λ₁) - ΦK.E₂ = (hc/λ₂) - ΦDividing equation (1) by equation (2), we getK.E₁/K.E₂ = λ₂/λ₁.
Substituting the given values, we get
1.10 eV/K.E₂ = 300.0 nm/400.0 nmK.E₂ = (1.10 eV)(400.0 nm)/(300.0 nm)K.E₂ = 1.83 eV
For more details about kinetic energy click here:
https://brainly.com/question/26472013#
#SPJ11
Helppp plsssssssssssssssssssssssss
Answer:
if it is -1^02
your answer is 1
50 points!
A. The object in the diagram above is called a(n)? _____
B. Given only the materials in the diagram, how can the strength of the magnetic field be increased? _____
Answer:
A. it is Electromagnet
B. there are 2 ways to increase the magnetic field in this situation.
by increasing the number of turns of wire in coilsecond, by increasing the current flowing. ( this step can not be achieved as the supply that is battery here, would not increase or decrease its current flow).
hence only by doing first way ( increase number of turns) magnetic field can be increased.
suppose that the current in an lc circuit (a circuit having only an inductor and capacitor in series) oscillates with a certain frequency. if the inductance is increased by a factor of 9.72 and the capacitance is increased by a factor of 6.12 by what factor is the frequency of oscillation multiplied?
The frequency of oscillation is multiplied by the square root of the product of the factors of inductance and capacitance. In this case, the frequency is multiplied by the square root of 9.72 multiplied by 6.12, which is equal to 11.3.
Suppose that the current in an LC circuit oscillates with a certain frequency. If the inductance is increased by a factor of 9.72 and the capacitance is increased by a factor of 6.12, the factor by which the frequency of oscillation is multiplied is calculated as follows:
Let L be the initial inductance and C be the initial capacitance of the LC circuit. The angular frequency of oscillation of the LC circuit is given by the expression [tex]\omega= 1/\sqrt{LC}[/tex] where ω is the angular frequency, L is the inductance, and C is the capacitance.
The new angular frequency of the LC circuit is ω′ = 1/√(L′C′)where L′ and C′ are the new inductance and capacitance, respectively. Let L′ = 9.72L and C′ = 6.12C. Substituting these values into the equation above gives ω′ = 1/√(9.72LC × 6.12C)ω′ = 1/√(59.4384LC)ω′ = (1/√59.4384) × (1/√(LC))ω′ = (0.161)ω.
Therefore, the factor by which the frequency of oscillation is multiplied is 0.161. Therefore, the frequency of oscillation is decreased by a factor of 6.192.
Learn more about the frequency of oscillation:
https://brainly.in/question/34373636
#SPJ11
if the ammeter has the following reading when set on the 0.05 a scale, what is the current it is measuring? a) 2 A. b) 0.2 A. c) 0.002 A. d) 0.02 A. e) 10 A.
The ammeter is measuring 0.02 A (0.02 Amps). To find this value, you need to multiply the reading on the scale (0.05 A) by the multiplier (40). The multiplier is the number of divisions on the scale multiplied by the least count of the scale.
In this case, the multiplier is 40 (4 divisions x 0.01 A least count). Therefore, the current measured is 0.02 A (0.05 A x 40 = 0.02 A). This is significantly less than the other values listed (2 A, 0.2 A, 0.002 A, and 10 A), so it is unlikely that the ammeter is measuring any of them.
An ammeter is an instrument used to measure electrical current. It is connected in series with the circuit, meaning that the current flows through the ammeter.
The reading is usually displayed on a scale, with each division having a particular least count. This least count is then multiplied by the number of divisions on the scale to get the multiplier. This multiplier is then multiplied by the reading on the scale to determine the current being measured.
Know more about ammeter here
https://brainly.com/question/18404570#
#SPJ11
as light travels from one medium to another, which of its properties change? (select all that apply.)
When light travels from one medium to another, its speed, direction, and wavelength can change, while its frequency remains constant. These changes are due to differences in the refractive indices of the two media.
As light travels from one medium to another, several of its properties change, including its speed, direction, and wavelength. The speed of light changes because the refractive index of each medium is different, which alters the velocity of the wave. The direction of the light may also change, a phenomenon known as refraction, as it enters a medium with a different refractive index. The amount of refraction depends on the angle of incidence, the angle between the incoming light and the normal line to the surface of the medium. Finally, the wavelength of the light may also change due to the refractive index of the medium, a phenomenon known as dispersion. This results in the separation of white light into its component colors when it passes through a prism or other refracting medium.
learn more about wavelength here:
https://brainly.com/question/13676179
#SPJ4
why do people live in areas affected by a natural strikes
Answer:
People tend to live in these areas because they believe that the benefits of the location outweigh the risks. Most volcanoes and seismic zones are safe for long periods between eruptions or seismic events. Often, tectonic events can be adjusted and residents perceive these events as predictable.
what is the maximum value of the electric field in an electromagnetic wave whose average intensity is 7.55 w/m2 ?
The maximum value of the electric field in an electromagnetic wave whose average intensity is 7.55 W/m² is 30.5 V/m.
An electromagnetic wave is a type of wave that is made up of electric and magnetic fields that fluctuate together. It is referred to as an electromagnetic wave because the electric and magnetic fields interact with each other, creating the wave's motion.
The equation for the average intensity of an electromagnetic wave is given by
I = 1/2εcE²
where I is the average intensity, ε is the permittivity of free space, c is the speed of light, and E is the maximum value of the electric field.
Equating the given value of average intensity to the equation,
7.55 W/m² = 1/2 × 8.85 × [tex]10^{-12}[/tex] F/m × (3 × [tex]10^{8}[/tex] m/s) × E²
simplifying and solving for E,
E = 30.5 V/m
Thus, the maximum value of the electric field in an electromagnetic wave whose average intensity is 7.55 W/m² is 30.5 V/m.
Know more about the Electric field here :
https://brainly.com/question/19878202
#SPJ11
two long straight wires are parallel and 8.0 cm apart. they are to carry equal currents such that the magnetic field at a point halfway between them has magnitude 300 ,ut. (a) should the currents be in the same or opposite directions? (b) how much current is
a) The currents should be in the same direction to produce a magnetic field of magnitude 300 uT.
b) To produce a magnetic field of magnitude 300 uT, the two wires must carry an equal current of [tex]I = \sqrt{(300*10^{-6} / (2*(4*\pi*10^{-7}))}[/tex] = 0.220 A.
The magnetic field is created by the combination of the two parallel wires and can be found using Ampere's Law: B = (μ0 * I) / (2π * d), where μ0 is the permeability of free space, I is the current, and d is the distance between the two wires.
When two long straight wires are parallel and 8.0 cm apart, and they are to carry equal currents such that the magnetic field at a point halfway between them has magnitude 300 μT, the currents should be in opposite directions. Let's find out how much current is required. Given:Magnetic field, B = 300 μT. Distance between two wires, d = 8 cm = 0.08 mWe need to find out the current required. Formula: Magnetic field due to the wire, B = µ₀I/(2πd) where µ₀ is the permeability of free space and I is the current. Substituting the given values in the above formula, we get:300 × 10⁻⁶ = (4π × 10⁻⁷) × I/(2π × 0.08)I = (300 × 2 × 0.08)/4π × 10⁻⁷I = 1.2 × 10⁴ A.
Therefore, the current required is 1.2 × 10⁴ A.(a) The currents should be in opposite directions.(b) The required current is 1.2 × 10⁴ A.
Learn more about Ampere's Law:
https://brainly.com/question/29812531
#SPJ11
The wave in which medium particles move perpendicular to the direction of wave is_________.Longitudinal waveTransverse waveBoth 1 and 2Neither 1 nor 2
The wave in which medium particles move perpendicular to the direction of wave is transverse wave. Option b is correct.
The wave in which medium particles move perpendicular to the direction of wave is a transverse wave. In a transverse wave, the motion of the particles in the medium is perpendicular to the direction of propagation of the wave. This means that when a transverse wave passes through a medium, the particles in the medium move up and down or side to side, perpendicular to the direction of the wave. Examples of transverse waves include light waves, electromagnetic waves, and waves on a string.
In contrast, in a longitudinal wave, the motion of the particles in the medium is parallel to the direction of propagation of the wave. Hence option b is correct choice.
To know more about waves, here
brainly.com/question/19129743
#SPJ4
What is the velocity of propagation for disturbances on the transmission line? (Use c = 1 ft/ns as the speed of light in a vacuum.)
vp = 0.5 ft/ns
vp = 1 ft/ns
vp = 0.25 ft/ns
vp = 2 ft/ns
QUESTION 8
How long does it take for a disturbance to traverse the entire length of the transmission line? Type your answer in nanoseconds to one place after the decimal.
QUESTION 9
What is the value of the generator reflection coefficient? Type your answer to three places after the decimal.
QUESTION 10
What is the value of the load reflection coefficient? Type your answer to three places after the decimal.
Question 8:How long does it take for a disturbance to traverse the entire length of the transmission line :
To find how long it takes for a disturbance to traverse the entire length of the transmission line, we can use the formula:
time = distance/velocity
The distance is given as 250 ft, and the velocity of propagation for disturbances on the transmission line is given as 0.5 ft/ns. Thus, we have:
time = 250/0.5 = 500 ns
Therefore, it takes 500 nanoseconds for a disturbance to traverse the entire length of the transmission line.
Answer: 500 ns
Question 9: What is the value of the generator reflection coefficient?
To find the generator reflection coefficient, we can use the formula:
Γg = (Z g - Z0)/(Z g + Z0)
where Z g is the load impedance, and Z0 is the characteristic impedance of the transmission line.
From the given values, we have:
Zg = (100 + j0) Ω
Z0 = (75 + j0) Ω
Substituting these values into the formula, we get:
Γg = (100 - 75)/(100 + 75) = 0.125
Therefore, the value of the generator reflection coefficient is 0.125 (to three decimal places).
Answer: 0.125
Question 10: What is the value of the load reflection coefficient?
To find the load reflection coefficient, we can use the formula:
ΓL = (ZL - Z0)/(ZL + Z0)
where ZL is the load impedance, and Z0 is the characteristic impedance of the transmission line.
From the given values, we have:
ZL = (75 - j100) Ω
Z0 = (75 + j0) Ω
Substituting these values into the formula, we get:
ΓL = (75 - j100 - 75)/(75 - j100 + 75) = -0.8 - j0.6
Therefore, the value of the load reflection coefficient is -0.8 - j0.6 (to three decimal places).
Answer: -0.8 - j0.6
To know more about load reflection here :
https://brainly.com/question/30551648
#SPJ11
a swimming pool is 20 ft wide and 40 ft long and its bot- tom is an inclined plane, the shallow end having a depth of 3 ft and the deep end, 9 ft. if the pool is full of water, find the hydrostatic force on (a) each of the four sides and (b) the bot- tom of the pool.
Hydrostatic force on each of the two longer sides: 4,242,774 N, Hydrostatic force on the shallow end of the pool: 3,378,717 N, Hydrostatic force on the bottom of the pool: 43,520,265 N
The hydrostatic force on each of the four sides and the bottom of the pool can be calculated using the principles of fluid mechanics. The hydrostatic force is the force exerted by the fluid (water) on the surface of the object (the pool).
(a) Hydrostatic force on each of the two longer sides:
[tex]F = pghA = 1000 kg/mx^{3} * 9.81 m/s^{2} * 1.83 m * 22.3 m^{2} = 4,242,774 N[/tex]
Hydrostatic force on the shallow end of the pool:
[tex]F = p ghA = 1000 kg/m^{3} * 9.81 m/s^{2} * 3 m * 11.15 m^{2} = 3,378,717 N[/tex]
(b) Hydrostatic force on the bottom of the pool:
F = ρghA = [tex]1000 kg/m^{3} * 9.81 m/s^{2} * 6 m * 74.32 m^{2} = 43,520,265 N[/tex]
To know more about Hydrostatic force, here
brainly.com/question/29856083
#SPJ4
when an object is placed 29.5 cm in front of a convex spherical mirror, a virtual image forms 12.0 cm behind the mirror. determine the mirror's focal length in cm and the magnification.
The focal length of the convex spherical mirror is 18.4 cm. The magnification is approximately equal to -0.41.
The distance of the object is 29.5 cm from the convex mirror and the image distance is 12.0 cm from the mirror.
The given mirror is a convex spherical mirror which means that the radius of the curvature of the mirror is positive. Therefore, we can use the mirror formula to calculate the focal length of the mirror.
The mirror formula is given by the equation:
1/f = 1/u + 1/v
Here,
f is the focal length of the mirror
u is the distance of the object from the mirror
v is the distance of the image from the mirror
The magnification of the mirror is given by the equation:
magnification, m = v/u
Now,
substituting the values given in the question in the above equations,
we get;
1/f = 1/29.5 + 1/12
Simplifying this equation gives, f ≈ 18.4 cm
Therefore, the focal length of the convex spherical mirror is 18.4 cm.
Now, the magnification of the mirror is given by the equation,
m = v/u = -12/29.5
Thus, the magnification is approximately equal to -0.41.
To know more about Focal length refer here:
https://brainly.com/question/16188698#
#SPJ11
at a location in europe, it is necessary to supply 300 kw of 60-hz power. the only powersource available operate at 50-hz. it is decided to generate the power by means of motor-generator set consisting of synchronous motor driving a synchronous generator. how manypoles should each of the two machines have in order to convert 50-hz to 60-hz power?
The synchronous motor should have 24 poles and the synchronous generator should have 20 poles in order to convert 50 Hz to 60 Hz power
Given that the location in Europe requires 300 kW of 60 Hz power and the only power source available operates at 50 Hz, it is decided to generate the power by means of a motor-generator set consisting of a synchronous motor driving a synchronous generator. It is required to find how many poles each of the two machines should have in order to convert 50 Hz to 60 Hz power.
Let the synchronous motor have ns number of poles and synchronous generator have ng number of poles.In a synchronous machine, the number of poles is directly proportional to the synchronous speed of the machine.
Hence, synchronous speed (n) is given by; n = 120f/p
where f is the frequency of the supply in Hz and p is the number of poles.
Since the generator is required to deliver power at 60 Hz, the synchronous speed of the generator should be 3600 RPM.∴ 3600 = 120 × 60 / ng
Solving this, we get;
[tex]n_g = 20[/tex]
Also, since the motor is supplied with a 50 Hz power supply, its synchronous speed should be 3000 RPM.∴ 3000 = 120 × 50 / [tex]n_s[/tex]
Solving this, we get; [tex]n_s[/tex] = 24
Therefore, the synchronous motor should have 24 poles and the synchronous generator should have 20 poles in order to convert 50 Hz to 60 Hz power.
To know more about Generator refer here :
https://brainly.com/question/12475693
#SPJ11
(LOOK AT PHOTO) Fill in the table with the distance and the displacement for each scenario
Answer: Below are the answers
Explanation:
Distance : 3 3+5+3 = 11 3+5+3+5 = 16
Displacement: 3 5 0
2. Distance : 4 4+3 = 7 4+3+5 = 12
Displacement : 4 5 0
tarzan steps off a branch and swings down on a vine that has an initial angle of 60 degrees relative to vertical. when the vine makes an angle of 30 degrees with the vertical, what fraction of his maximum kinetic energy will he have at that moment?
To determine the fraction of Tarzan's maximum kinetic energy when the vine makes an angle of 30 degrees with the vertical, we need to use the conservation of energy.
Tarzan's initial potential energy is converted into kinetic energy as he swings down on the vine. When the vine makes an angle of 30 degrees with the vertical, Tarzan's potential energy has decreased by half, so his kinetic energy must have increased by the same amount. Therefore, at this point, Tarzan has half of his maximum kinetic energy. We can express this as a fraction by dividing the current kinetic energy (half the maximum) by the maximum kinetic energy, giving a fraction of 1/2.
To know more about conservation of energy, here
brainly.com/question/2137260
#SPJ4
a rigid tank of volume 2 m3 initially contains air at 0.21 bar, 290 k. a leak develops and air flows in slowly from the surroundings which are at 1.1 bar, 312 k. after a while, the tank and its surroundings come to equilibrium. what is the final temperature in the tank, in oc, and how much mass has entered the tank, in kg? neglect kinetic and potential energy effects, and assume the air is an ideal gas with constant specific heats evaluated at 300 k.
The final temperature in the tank is 33.85°C. The amount of mass entered the tank is 0.0108 kg/s.
The mass flow rate can be calculated using the mass balance equation for a steady-state control volume. Since the tank is rigid, its volume is constant, and the mass balance equation simplifies to:
m = p₂V/(RT₂) - p₁V/(RT₁)
where V is the volume of the tank, R is the universal gas constant, and m is the mass flow rate.
Substituting the given values:
p₁ = 0.21 bar
p₂ = 1.1 bar
T₁ = 290 K
T₂ = 312 K
V = 2 m³
R = 8.314 J/mol·K
we get:
m = (1.1)(2)/(8.314)(312) - (0.21)(2)/(8.314)(290) = 0.0108 kg/s
The final temperature in the tank can be calculated using the energy balance equation for a steady-state control volume. Since the tank is rigid, its volume is constant, and the energy balance equation simplifies to:
T = T₁ + (m)(R)(T₂ - T₁))/(m)(Cv)
where T is the final temperature of the air in the tank, Cv is the constant-volume specific heat of the air, and all other symbols have their usual meanings.
Substituting the given values:
Cv = Cp - R = 1.005 - 0.287 = 0.718 kJ/kg·K
(since the air is assumed to be an ideal gas with constant specific heats evaluated at 300 K)
T₁ = 290 K
T₂ = 312 K
m = 0.0108 kg/s
R = 8.314 J/mol·K
we get:
T = 290 + (0.0108)(8.314)(312 - 290)/(0.0108)(0.718) = 307 K
The final temperature in the tank is 307 K, which is equivalent to 33.85°C. The mass that has entered the tank is 0.0108 kg/s.
Learn more about mass flow rate here: https://brainly.com/question/30618961
#SPJ11
I want a molecule consist of 200 out of and one option in Health together by
The dsDNA molecule with 200 nucleotides and 20% guanine would have a total of 240 hydrogen bonds.
Calculating the number of hydrogen bonds in the moleculeIn a double-stranded DNA molecule, the number of hydrogen bonds between complementary base pairs determines the stability of the molecule.
Guanine (G) pairs with cytosine (C), and adenine (A) pairs with thymine (T), with each base pair forming a specific number of hydrogen bonds.
The number of hydrogen bonds in a G-C base pair is three, while the number of hydrogen bonds in an A-T base pair is two.
Therefore, to determine the number of hydrogen bonds in a dsDNA molecule with 20% guanine, we first need to calculate the number of guanine-cytosine base pairs.
If 20% of the nucleotides are guanine, then 20% of the nucleotides will be cytosine as well (since G always pairs with C). The remaining 60% will be made up of adenine and thymine in equal amounts.So out of the 200 nucleotides, 20% will be guanine and 20% will be cytosine, which means there will be 40% G-C base pairs.
The number of G-C base pairs can be calculated by multiplying the total number of base pairs (200/2 = 100, since each nucleotide pairs with one other nucleotide) by the percentage of G-C base pairs (40% or 0.4):
Number of G-C base pairs = 100 x 0.4 = 40
Therefore, the total number of hydrogen bonds in the dsDNA molecule would be:
Number of hydrogen bonds = (number of G-C base pairs x 3) + (number of A-T base pairs x 2)
= (40 x 3) + (60 x 2)
= 120 + 120
= 240
So the total number of hydrogen bonds in the dsDNA molecule is 240
Read more about hydrogen bonds at
https://brainly.com/question/13935578
#SPJ1
Complete question
A dsDNA molecule consists of 200 nucleotides with 20% guanine.
What is the number of hydrogen bonds in that molecule ? 1) 360 2) 260 3) 180 4) 240