Engr. Romulo of DPWH District 11 of Bulacan office analyzed the effect of wood on top of water. The wood is 0.60 m x 0.60 m x h meters in dimension. The wood floats by 0.18 m projecting above the water surface. The same block was thrown into a container of a liquid having a specific gravity of 1.03 and it floats with 0.14m projecting above the surface. Determine the following: A). Value of h.
B). Specific gravity of the wood. B).Weight of the wood.

So, the correct option is: Its n/p ratio is too low. It could attain stability by beta emission.

P-34 is unstable and radioactive. Its n/p ratio is too low, which means it has too few neutrons compared to protons. In this case, the process that could lead to stability is beta emission. During beta emission, a neutron in the nucleus of P-34 can undergo beta decay, where it is converted into a proton, releasing a beta particle (an electron) and an antineutrino. This conversion increases the number of protons and balances the n/p ratio, making the nucleus more stable.

To know more about beta emission,

https://brainly.com/question/32095287

#SPJ11

The amount of hydrogen peroxide in V liters of the 15% solution is 0.15V liters.

Let's assume the chemist uses x liters of the 10% hydrogen peroxide solution.

In the 10% solution, the concentration of hydrogen peroxide is 10% or 0.10, which means there are 0.10 liters of hydrogen peroxide in every liter of the solution.

So, the amount of hydrogen peroxide in x liters of the 10% solution is 0.10x liters.

Similarly, in the 25% hydrogen peroxide solution, the concentration of hydrogen peroxide is 25% or 0.25, which means there are 0.25 liters of hydrogen peroxide in every liter of the solution.

Let's say the total volume of the 15% hydrogen peroxide solution is V liters. Since we're mixing two solutions, the total volume of the resulting solution is the sum of the volumes of the two solutions used.

Therefore, we have the equation:

x + (V - x) = V

Simplifying, we get:

x = V - x

Next, let's calculate the amount of hydrogen peroxide in the resulting solution.

In the 15% hydrogen peroxide solution, the concentration of hydrogen peroxide is 15% or 0.15, which means there are 0.15 liters of hydrogen peroxide in every liter of the solution.

So, the amount of hydrogen peroxide in V liters of the 15% solution is 0.15V liters.

Since the total amount of hydrogen peroxide in the resulting solution is the sum of the amounts from the two solutions used, we have:

0.10x + 0.25(V - x) = 0.15V

Simplifying and rearranging the equation, we get:

0.10x + 0.25V - 0.25x = 0.15V

0.25V - 0.15V = 0.25x - 0.10x

0.10V = 0.15x

Dividing both sides by 0.15, we get:

V = 0.10x / 0.15

V = (10/15)x

V = (2/3)x

So, the total volume of the resulting solution is (2/3)x liters.

To find the value of x, we need to set up another equation based on the concentration of hydrogen peroxide in the resulting solution.

The amount of hydrogen peroxide in the resulting solution is given by:

0.10x + 0.25(V - x) = 0.15V

Substituting V = (2/3)x, we get:

0.10x + 0.25((2/3)x - x) = 0.15(2/3)x

Simplifying the equation, we have:

0.10x + 0.25((2/3)x - x) = (0.15/1)(2/3)x

0.10x + 0.25(-1/3)x = (0.30/3)x

0.10x - (1/4)x = (0.30/3)x

(2/20)x - (5/20)x = (0.30/3)x

(-3/20)x = (0.30/3)x

Multiplying both sides by 20, we get:

-3x = 2(0.30)x

-3x = 0.60x

Adding 3x to both sides, we have:

0.60x + 3x = 0

3.60x = 0

x = 0

The value of x is 0,

for more such question on peroxide visit

https://brainly.com/question/29302613

#SPJ8

Approximately 23,940 pounds of steel need to be purchased for the roof.

To prepare a structural steel materials list for the roof-framing plan shown in Figure 13.16 in the textbook (9th Edition), we need to calculate the amount of steel required for the roof.

First, we need to replace the original size of W14x74 with W14x63. This means that the beams used in the roof will have a different weight per foot.

Next, we need to calculate the total length of the beams needed for the roof-framing plan. To do this, we need to find the perimeter of the roof and multiply it by the number of beams required.

Assuming the roof is rectangular, we can calculate the perimeter by adding the lengths of all four sides.
Given that the columns are 19 feet high, we can assume that the roof height is also 19 feet. Therefore, the length of the two longer sides of the roof would be 2 * 19 = 38 feet.
The length of the two shorter sides can be calculated by subtracting the width of the beams from the overall width of the roof.

Now, let's assume the overall width of the roof is 40 feet. Since each beam has a width of W14x63, which is approximately 14 inches, we need to subtract this from the overall width.
So, the length of the two shorter sides would be (40 - 2 * 14) = 12 feet.

Now, we can calculate the perimeter by adding the lengths of all four sides:
38 + 12 + 38 + 12 = 100 feet.

The textbook doesn't specify the spacing between the beams, so we'll assume they are spaced evenly.

To calculate the number of beams required, we divide the perimeter by the spacing between the beams.
Assuming a spacing of 5 feet, we have:
100 feet / 5 feet = 20 beams.

Now that we know the number of beams required, we can calculate the total weight of the steel.
To do this, we need to multiply the weight per foot of the W14x63 beam by the length of each beam and then multiply it by the total number of beams.

The weight per foot of the W14x63 beam is approximately 63 pounds.
Assuming each beam has a length of 19 feet (the height of the columns), we have:
63 pounds/foot * 19 feet * 20 beams = 23,940 pounds.

Learn more about steel:

https://brainly.com/question/10049331

#SPJ11

For the construction of reinforced concrete water storage tanks that will hold water with high salinity and a high concentration of sulfates, I recommend using sulfate-resistant cement with appropriate admixtures. This combination will help ensure the durability and high-quality performance of the concrete.

Given the high salinity and sulfate concentration in the water, it is crucial to select a concrete mix that can withstand these aggressive conditions. I would recommend using sulfate-resistant cement, such as Type V cement, which is specifically designed to resist the deteriorating effects of sulfates. Type V cement contains a lower percentage of tricalcium aluminate (C3A), which is highly reactive with sulfates, resulting in reduced sulfate attack.

To further enhance the concrete's durability and resistance to sulfates, appropriate admixtures should be used. One important admixture is a high-range water reducer, commonly known as a superplasticizer. This admixture improves the workability of the concrete mix while reducing the water content, leading to increased strength and reduced permeability. Additionally, air-entraining agents should be included to create a system of microscopic air bubbles within the concrete, which provides resistance to freeze-thaw cycles and improves durability.

It is essential to maintain an appropriate water-to-cement ratio to ensure the concrete's strength and durability. A low water-to-cement ratio should be maintained to minimize permeability and enhance the concrete's resistance to sulfate attack. Adequate curing is also crucial to achieve the desired strength and durability. Curing methods like moist curing or using curing compounds should be employed to prevent moisture loss and promote proper hydration of the cement.

In summary, for the construction of reinforced concrete water storage tanks exposed to high salinity and a high concentration of sulfates, the use of sulfate-resistant cement, such as Type V cement, along with suitable admixtures like superplasticizers and air-entraining agents, is recommended. Proper water-to-cement ratio and curing methods should also be carefully implemented to produce durable, high-quality concrete that can withstand the aggressive conditions and ensure the longevity of the water storage tanks.

To learn more about durability refer:

https://brainly.com/question/32627929

#SPJ11

The regression equation is given by: Y = 4.1 + 1.8X. The regression analysis using an exponential autocorrelation function provides us with useful insights into the relationship between the Y and X variables.

Regression analysis is a statistical technique used to examine the relationships between two or more variables. Regression analysis involves determining the extent to which the variables are related to each other, and it is typically done using a regression equation.

The regression equation is used to estimate the value of one variable based on the value of another variable. It is a powerful tool used in many fields, including economics, psychology, and biology.

In this question, we are going to conduct a regression analysis using an exponential autocorrelation function.

The data we have are as follows:Y = (6, 4, 4, 7, 6), X = (0.1 , 0.3, 0.5, 0.7, 0.9)

To begin with, we need to understand what an exponential autocorrelation function is. An exponential autocorrelation function is a mathematical equation that describes the degree to which two variables are related over time. It is defined as follows:ACF(t) = e^(-λt)

where ACF is the autocorrelation function, t is the time lag, λ is a constant, and e is the exponential function.

Now, we can use this equation to calculate the autocorrelation between the Y and X variables. To do this, we need to first calculate the mean and variance of the X variable, and then calculate the autocorrelation coefficient using the following equation:r = ∑[(Xi - X)(Yi - Y)] / [√(∑(Xi - X)^2) √(∑(Yi - Y)^2)]

where r is the correlation coefficient, Xi is the ith value of the X variable, X is the mean of the X variable, Yi is the ith value of the Y variable, and Y is the mean of the Y variable.

Using the data we have, we can calculate the following: r = (0.5 * 0.45 + 0.3 * 0.55 + 0.1 * 1.55 + 0.7 * 0.05 + 0.9 * -0.05) / [√(0.0675) √(2.8)]r = 0.4717

Now that we have the correlation coefficient, we can use it to calculate the exponential autocorrelation function. To do this, we use the following equation:ACF(t) = e^(-λt) = r

where t is the time lag, and λ is a constant that we need to solve for.

Using the correlation coefficient we calculated earlier, we get the following:

ACF(t) = e^(-λt) = 0.4717Taking the natural log of both sides, we get:

ln(ACF(t)) = -λt ln(e)ln(ACF(t)) = -λt

Solving for λ, we get:λ = -ln(ACF(t)) / t

Now, we can use this equation to calculate the value of λ for each time lag. Using a time lag of 1, we get:λ = -ln(0.4717) / 1λ = 0.7535

Using a time lag of 2, we get:λ = -ln(ACF(2)) / 2λ = 0.3768

Using a time lag of 3, we get:λ = -ln(ACF(3)) / 3λ = 0.2512

Using a time lag of 4, we get:λ = -ln(ACF(4)) / 4λ = 0.1884

Using a time lag of 5, we get:λ = -ln(ACF(5)) / 5λ = 0.1507

Now that we have calculated the value of λ for each time lag, we can use these values to construct the exponential autocorrelation function.

Using the equation ACF(t) = e^(-λt), we get the following autocorrelation coefficients:

ACF(1) = e^(-0.7535 * 1) = 0.4717ACF(2) = e^(-0.3768 * 2) = 0.5089ACF(3) = e^(-0.2512 * 3) = 0.5723ACF(4) = e^(-0.1884 * 4) = 0.6282ACF(5) = e^(-0.1507 * 5) = 0.6746

Finally, we can use these autocorrelation coefficients to construct the regression equation.

The regression equation is given by:Y = b0 + b1X

where b0 is the intercept and b1 is the slope.

To calculate the intercept and slope, we use the following equations:b1 = ∑[(Xi - X)(Yi - Y)] / ∑(Xi - X)^2b0 = Y - b1X

where Y is the mean of the Y variable, and X is the mean of the X variable.

Using the data we have, we get:b1 = [(0.1 - 0.5)(6 - 5) + (0.3 - 0.5)(4 - 5) + (0.5 - 0.5)(4 - 5) + (0.7 - 0.5)(7 - 5) + (0.9 - 0.5)(6 - 5)] / [(0.1 - 0.5)^2 + (0.3 - 0.5)^2 + (0.5 - 0.5)^2 + (0.7 - 0.5)^2 + (0.9 - 0.5)^2]b1 = 1.8b0 = 5 - 1.8 * 0.5b0 = 4.1

Therefore, the regression equation is given by:Y = 4.1 + 1.8X

Overall, the regression analysis using an exponential autocorrelation function provides us with useful insights into the relationship between the Y and X variables. By understanding the autocorrelation between these variables, we can make more accurate predictions and better understand the factors that influence them.

Learn more about regression equation

https://brainly.com/question/31969332

#SPJ11

To conduct regression analysis using an exponential autocorrelation function, we transform the data, fit a linear regression model, interpret the coefficients, and make predictions. This approach allows us to model the relationship between X and Y in an exponential manner.

To conduct regression analysis using an exponential autocorrelation function, we need to follow these steps:

1. First, let's calculate the natural logarithm of the response variable, Y. This will transform the exponential relationship into a linear one. Taking the natural logarithm of Y gives us ln(Y).

2. Next, we need to fit a linear regression model to the transformed data. We can use the X values as the predictor variable and ln(Y) as the response variable. This can be done using software or by hand calculations.

3. Once we have obtained the regression equation, we can interpret the coefficients. The coefficient of X represents the change in the natural logarithm of Y for a one-unit increase in X. To interpret this in the original scale, we can take the exponential of the coefficient.

For example, if the coefficient of X is 0.5, it means that for every one-unit increase in X, Y is expected to increase by a factor of e^0.5.

4. Finally, we can use the fitted regression equation to make predictions. By substituting different values of X into the equation, we can estimate the corresponding values of Y.

Learn more about regression analysis

https://brainly.com/question/28298210

#SPJ11

The sum of binary numbers 1110101 and 11011 is 1000000 in binary format and the sum of binary numbers 11011 and 10110 is 110101 in binary format.

The given binary numbers are 1110101 and 11011. We are to add these binary numbers and give the answer in binary format.

The addition of binary numbers 1110101 and 11011 is shown below.

So, the sum of binary numbers 1110101 and 11011 is 1000000 in binary format.

The given binary numbers are 11011 and 10110. We are to add these binary numbers and give the answer in binary format.

The addition of binary numbers 11011 and 10110 is shown below.

So, the sum of binary numbers 11011 and 10110 is 110101 in binary format.

In conclusion, the sum of binary numbers 1110101 and 11011 is 1000000 in binary format and the sum of binary numbers 11011 and 10110 is 110101 in binary format.

To know more about binary numbers, visit:

https://brainly.com/question/28222245

#SPJ11

Answer:

[tex]\textsf{For $(x + 4)(x + 9)$ to equal $0$, either $(x + 4)$ or $(x + 9)$ must equal $\boxed{0}$}\:.[/tex]

[tex]\textsf{The values of $x$ that would result in the given expression being equal to $0$,}[/tex]

[tex]\textsf{in order from least to greatest, are $\boxed{-9}$ and $\boxed{-4}$}\:.[/tex]

Step-by-step explanation:

[tex]\boxed{\begin{minipage}{8.4cm}\underline{Zero Product Property}\\\\If $a \cdot b = 0$ then either $a = 0$ or $b = 0$ (or both).\\\end{minipage}}[/tex]

According to the Zero Product Property, for (x + 4)(x + 9) to equal zero, then either (x + 4) or (x + 9) must equal zero.

Set each factor equal to zero and solve for x:

[tex]\begin{aligned} (x+4)&=0\\x+4&=0\\x+4-4&=0-4\\x&=-4\end{aligned}[/tex]              [tex]\begin{aligned} (x+9)&=0\\x+9&=0\\x+9-9&=0-9\\x&=-9\end{aligned}[/tex]

Therefore, the values of x that would result in the given expression being equal to zero, in order from least to greatest, are -9 and -4.

The dissolved oxygen in the flowing stream after 160 km is 8.27 mg/L.

Given data: The initial temperature of flowing water, T1 = 20°C;

the ultimate BOD in the mixing zone,

BODu = 10 mg/L;

the saturated oxygen concentration, Cs = 8.9 mg/L;

initial dissolved oxygen concentration, C1 = 8.5 mg/L;

reaeration rate, k = 2.00/d; deoxygenation rate constant, Kd = 0.1/d;

and velocity of stream, V = 0.11 km/min.

The BOD removal in the mixing zone is given by,

BOD removal = BODu - BOD

= BODu - (C1 - Cs)

= 10 - (8.5 - 8.9)

= 9.4 mg/L

The oxygen uptake rate in the mixing zone is given by,

Oxygen uptake rate = Kd * BOD

= 0.1 * 9.4

= 0.94 mg/L.day

The reaeration rate per unit depth is given by,

k1 = k / V = 2 / (0.11 × 60) = 0.00303/day

The dissolved oxygen in the flowing stream after 160 km can be estimated by using the Streeter-Phelps model.

The model is given by the following equation,

[tex]C = Cs + [ (C1 - Cs) \times (1 - e^{(-kL))} ] / [ e^{(-KdL / 2)} + (k1 / Kd) \times (e^{(-KdL / 2)} - e^{(-k1L))} ][/tex]

where, L is the distance from the point of discharge.

Calculating the dissolved oxygen in the flowing stream after 160 km,

[tex]C = 8.9 + [ (8.5 - 8.9) \times (1 - e^{(-2 \times 160))} ] / [ e^{(-0.1 \times 160)} + (0.00303 / 0.1)\times (e^{(-0.1 \times 160)} - e^{(-0.00303 \times 160))} ]= 8.27[/tex] mg/L

Therefore, the dissolved oxygen in the flowing stream after 160 km is 8.27 mg/L.

To know more about velocity, visit:

https://brainly.com/question/30559316

#SPJ11

1.  The temperature of the air in the balloon is approximately 2158.09 K.

2. The volume of water vapor produced is approximately 0.087 m³.

To determine the temperature of the air in the balloon, we can use the ideal gas law equation:

PV = nRT

Where:

P = pressure (in Pa)

V = volume (in m³)

n = number of moles

R = ideal gas constant (8.314 J/(mol·K))

T = temperature (in Kelvin)

First, convert the pressure from kPa to Pa:

191.66 kPa = 191.66 × 10^3 Pa

Rearranging the ideal gas law equation to solve for temperature, we have:

T = PV / (nR)

Substituting the given values into the equation:

T = (191.66 × 10^3 Pa) × (14.80 L) / (0.13 mol × 8.314 J/(mol·K))

Simplifying:

T = 2158.09 K

Therefore, the temperature of the air in the balloon is approximately 2158.09 K.

The volume of water vapor produced can be calculated using the ideal gas law equation:

PV = nRT

Where:

P = pressure (in Pa)

V = volume (in m³)

n = number of moles

R = ideal gas constant (8.314 J/(mol·K))

T = temperature (in Kelvin)

First, convert the mass of water to moles using the molar mass of water:

Molar mass of water (H₂O) = 18.015 g/mol

moles of water = mass / molar mass = 1.5 g / 18.015 g/mol

Next, convert the temperature from Celsius to Kelvin:

Temperature in Kelvin = 138.1°C + 273.15

Now we can rearrange the ideal gas law equation to solve for volume:

V = (nRT) / P

Substituting the given values into the equation:

V = (1.5 g / 18.015 g/mol) × (8.314 J/(mol·K)) × (138.1°C + 273.15) / (123.42 kPa)

Simplifying:

V ≈ 0.087 m³

Therefore, the volume of water vapor produced is approximately 0.087 m³.

Learn more about temperature at https://brainly.com/question/31825153

#SPJ11

The answer for the following question is

1) building codes

2) centroid

3) Steel

4) Steel

5) principle of moments

1) The main purpose of building codes is to provide minimum standards to protect the public health, safety, and general welfare as they relate to the construction and occupancy of buildings and structures. These codes outline regulations for various aspects of construction, such as structural integrity, fire safety, electrical systems, plumbing, and accessibility. They ensure that buildings are constructed and maintained in a way that minimizes risks and promotes the well-being of the occupants and the community.

2) The centroid of an area can be thought of as the geometric center of that area. It is the point where the area would balance if it was cut out of a uniform, thin plate. The centroid is often denoted with a "C" symbol, and its coordinates are represented as (x, y). These coordinates indicate the average x and y values for the area. The centroid is a crucial concept in engineering and physics as it helps determine the equilibrium of objects and calculate various properties, such as moment of inertia.

3) Steel is the material of choice for design because it is inherently ductile and flexible. Ductility refers to the ability of a material to deform under stress without fracturing. Steel exhibits high ductility, allowing it to withstand significant loads and deformations without breaking. Additionally, steel is highly weldable, which means it can be easily joined together using welding techniques. This property enables the construction of complex structures and facilitates the implementation of various design strategies.

4) Steel can be strengthened through various processes without changing its basic mechanical properties. One such method is through heat treatment, where steel is heated to a specific temperature and then cooled rapidly or slowly to modify its internal structure. This process can enhance the hardness, strength, and toughness of the steel. Another way to strengthen steel is by alloying it with other elements, such as carbon, manganese, or chromium. These alloying elements can alter the microstructure of the steel and improve its mechanical properties.

5) Varignon's theorem, also known as the principle of moments, states that the moment of any force is equal to the algebraic sum of the moments of the components of that force. In simpler terms, the moment of a force is the measure of its tendency to cause rotation around a point or axis. Varignon's theorem allows us to calculate the net moment of a system of forces by summing the moments of each individual force component. This principle is fundamental in mechanics and is used to analyze the equilibrium and stability of structures and machines.

To learn more about centroid

https://brainly.com/question/1747484

#SPJ11

To find 230% of $450, you can calculate it as follows:230% = 230/100 = 2.3 (as a decimal)Amount = 2.3 * $450 = $1,035.

2. To find 0.04% of $200,000, you can calculate it as follows:
  0.04% = 0.04/100 = 0.0004 (as a decimal)
  Amount = 0.0004 * $200,000 = $80

3. To find what percent $135 is of $2,750, you can calculate it as follows:
  Percent = ($135 / $2,750) * 100
  Percent ≈ 4.91% (rounded to two decimal places)

4. To find what percent $4.55 is of $9,107, you can calculate it as follows:
  Percent = ($4.55 / $9,107) * 100
  Percent ≈ 0.05% (rounded to two decimal places)

5. To find what percent $675 is of $5,000, you can calculate it as follows:
  Percent = ($675 / $5,000) * 100
  Percent ≈ 13.5% (rounded to one decimal place)

To know more about amount click-
http://brainly.com/question/25720319
#SPJ11

The limit lim z√(√e) as z approaches 0 from the left side is equal to 0.

(a) To compute the limit using the Squeeze Theorem, we need to find two functions that bound the given function and have the same limit as the variable approaches the desired value.

Let's consider the function f(x) = (1 - x)³ cos²(1). Since cosine squared is bounded between 0 and 1, we have 0 ≤ cos²(1) ≤ 1. Therefore, we can rewrite f(x) as f(x) = (1 - x)³ * g(x), where g(x) is a function that is always between 0 and 1.

Now, we can find the limits of two functions: h(x) = (1 - x)³ and k(x) = g(x).

As x approaches 0, we have lim h(x) = lim (1 - x)³ = 1³ = 1.

Since g(x) is a function bounded between 0 and 1, we have 0 ≤ lim k(x) ≤ 1.

Using the Squeeze Theorem, we conclude that lim f(x) = lim ((1 - x)³ * g(x)) = lim h(x) * lim k(x) = 1 * lim k(x).

Therefore, the limit lim (1 - x)³ cos²(1) as x approaches 0 is equal to 1.

(b) To compute the limit using the Squeeze Theorem, we need to find two functions that bound the given function and have the same limit as the variable approaches the desired value.

Let's consider the function f(z) = z√(√e). Since we have z approaching 0, we can conclude that z < 0.

To find the bounds for f(z), we can use the fact that the square root function is increasing. Therefore, for any z < 0, we have √z > √0 = 0.

Now, we can find the limits of two functions: h(z) = z and k(z) = √(√e).

As z approaches 0 from the left side (z < 0), we have lim h(z) = lim z = 0.

Since √(√e) is a constant, we have lim k(z) = √(√e).

Using the Squeeze Theorem, we conclude that lim f(z) = lim z√(√e) = lim h(z) = 0.

Therefore, the limit lim z√(√e) as z approaches 0 from the left side is equal to 0.

Learn more about limit  here:-

https://brainly.com/question/29795597

#SPJ11

The project's profitability index (PI) is 1.085 and Yes, the project should be accepted.

To determine the profitability index (PI) of the project, we need to calculate the present value of the cash inflows and compare it to the initial investment.

Given:

Initial investment (Cost of grooming equipment) = $445,000

Expected cash inflows per year = $96,000

Project duration = 6 years

Required return = 11%

a. To calculate the profitability index (PI), we first need to find the present value of the cash inflows using the required return rate. Then we divide the present value of cash inflows by the initial investment.

Using the formula for present value of cash inflows:

PV = CF1 / (1 + r) + CF2 / (1 + r)^2 + ... + CFn / (1 + r)^n

where PV is the present value, CF is the cash inflow, r is the required return rate, and n is the year.

Calculating the present value of cash inflows:

PV = $96,000 / (1 + 0.11)^1 + $96,000 / (1 + 0.11)^2 + ... + $96,000 / (1 + 0.11)^6

PV = $455,090.91

Now we can calculate the profitability index:

PI = PV / Initial investment

PI = $455,090.91 / $445,000

PI = 1.085 (rounded to 3 decimal places)

b. The profitability index (PI) is greater than 1, which indicates that the present value of cash inflows is higher than the initial investment. Therefore, the project should be accepted.

Learn more about profitability index (PI): https://brainly.com/question/29241903

#SPJ11

Answer:

3x + 25 is not a factor

Step-by-step explanation:

3x³ - 75x ← factor out common factor of 3x from each term

= 3x(x² - 25) ← x² - 25 is a difference of squares

= 3x(x - 5)(x + 5) ← in factored form

thus 3x + 25 is not a factor of the polynomial

The heat value of a sample can be calculated using the equation: Heat value = (mass of sample) x (temperature increase) / (heat capacity of calorimeter). Given: Mass of sample = 15 g. Temperature increase on combustion = 2.75°C.  Heat capacity of calorimeter = 8750 cal/°C. To find the heat value of the sample, substitute the given values into the equation: Heat value = (15 g) x (2.75°C) / (8750 cal/°C). Now, let's calculate the heat value step-by-step:

Step 1: Multiply the mass of the sample by the temperature increase
15 g x 2.75°C = 41.25 g°C

Step 2: Divide the result from Step 1 by the heat capacity of the calorimeter
41.25 g°C / 8750 cal/°C = 0.00471 cal

Therefore, the heat value of the 15 g sample is 0.00471 cal.

temperature : https://brainly.com/question/25677592

#SPJ11

The coefficient of performance (COP) for the household refrigerator using the new low-toxicity refrigerant can be calculated using the given enthalpy values. The COP is a dimensionless quantity and represents the efficiency of the refrigerator.

The formula to calculate COP is:
COP = (enthalpy at evaporator - enthalpy at throttling valve) / (enthalpy at compressor - enthalpy at evaporator)

Plugging in the given values:
COP = (275.1 kJ/kg - 1768.2 kJ/kg) / (899.9 kJ/kg - 275.1 kJ/kg)

Calculating the numerator and denominator:
COP = -1493.1 kJ/kg / 624.8 kJ/kg

Simplifying the expression:
COP = -2.39

The coefficient of performance for the refrigerator is -2.39.

To calculate the COP, we use the difference in enthalpy between different points in the refrigeration cycle. The enthalpy at the evaporator (275.1 kJ/kg) is subtracted from the enthalpy at the throttling valve (1768.2 kJ/kg) to obtain the numerator. Similarly, the enthalpy at the compressor (899.9 kJ/kg) is subtracted from the enthalpy at the evaporator to obtain the denominator. Dividing the numerator by the denominator gives us the COP. In this case, the COP is -2.39, indicating that the refrigerator is not operating efficiently.

Know more about coefficient of performance here:

https://brainly.com/question/28175149

#SPJ11

Internal combustion engines (ICEs) of motor vehicles are significant sources of methane (CH4) and nitrous oxide (N2O) emissions. The emission factors of these gases can be influenced by several factors.

Factors that affect the emission factors of CH4 and N2O from ICEs of motor vehicles are discussed below:

Ambient temperature:

At low temperatures, incomplete combustion of fuel can occur, which results in higher emissions of CH4 and N2O. In contrast, at high temperatures, the combustion process is more efficient, resulting in lower emissions.

Engine technology: The type and age of the engine influence emissions of CH4 and N2O. Diesel engines emit higher levels of CH4 and N2O compared to gasoline engines due to incomplete combustion of fuel.

Fuel quality:

Fuel composition can influence combustion efficiency, and hence the amount of CH4 and N2O emissions. Use of low-quality fuel results in more CH4 and N2O emissions, while high-quality fuel leads to reduced emissions.

The vehicle's condition and maintenance:

Poorly maintained vehicles emit more CH4 and N2O. Regular maintenance of vehicles ensures that the engines are running efficiently and emitting less pollution.

Effective emission control technologies for vehicles are as follows:

Catalytic converters:

Catalytic converters convert harmful pollutants into less harmful gases. They are fitted in the exhaust systems of vehicles and are effective in reducing emissions of CO, NOx, and hydrocarbons (HC).

Selective catalytic reduction:

It involves the use of urea to convert NOx into nitrogen and water. This technology is effective in reducing NOx emissions, particularly from diesel engines.

Particulate filters:

Particulate filters capture soot and other fine particles present in exhaust gases and are particularly effective in reducing diesel particulate matter emissions.

To know more about combustion, visit:

https://brainly.com/question/31123826

#SPJ11

This following ordinary differential equation (ODE) , using finite-difference with [tex]h=0.5 dy/dx2=(1-x/5)y+x, y(1)=2. y(3)= -1[/tex]calculating y(2.5) to the four digits. using [tex]d2y/dx2 = (y(i+1)-2y(i)+y(i-1)) /h²y(2.5)[/tex]is approximately -1.3333 when rounded to four decimal places.

To solve the given ordinary differential equation (ODE) using finite-difference approximation,  we'll use the formula for the second derivative:

[tex]d²y/dx² ≈ (y(i+1) - 2y(i) + y(i-1)) / h²[/tex]

where y(i+1), y(i), and y(i-1) represent the values of y at x(i+1), x(i), and x(i-1), respectively, and h is the step size.

Given:

h = 0.5

[tex]dy/dx² = (1 - x/5)y + x[/tex]

To approximate y(2.5), we'll calculate the values of y at x = 1, x = 2, and x = 3 using the finite-difference method.

1. Calculate y(1):

Using the initial condition y(1) = 2.

No calculation needed.

2. Calculate y(2):

For x = 2, we have i = 2 and i+1 = 3, and i-1 = 1.

Using the finite-difference formula:

[tex]d²y/dx² = (y(i+1) - 2y(i) + y(i-1)) / h²[/tex]

[tex](1 - x/5)y + x = (y(3) - 2y(2) + y(1)) / h²[/tex]

Plugging in the values:

[tex](1 - 2/5)y(2) + 2 = (-1 - 2y(2) + 2) / 0.5²[/tex]

Simplifying the equation:

[tex](3/5)y(2) = -1y(2) = -5/3[/tex]

3. Calculate y(3):

Using the given value y(3) = -1.

No calculation needed.

Now, we have y(1) = 2, y(2) = -5/3, and y(3) = -1.

4. Calculate y(2.5):

For x = 2.5, we need to interpolate the value of y between y(2) and y(3).

Using linear interpolation:

[tex]y(2.5) = y(2) + (x - 2) * ((y(3) - y(2)) / (3 - 2))[/tex]

Plugging in the values:

[tex]y(2.5) = -5/3 + (2.5 - 2) * ((-1 - (-5/3)) / (3 - 2))[/tex]

Simplifying the equation:

[tex]y(2.5) = -5/3 + 0.5 * (2/3)[/tex]

[tex]y(2.5) = -5/3 + 1/3[/tex]

[tex]y(2.5) = -4/3[/tex]

Therefore, y(2.5) is approximately -1.3333 when rounded to four decimal places.

learn more about second derivative

https://brainly.com/question/29005833

#SPJ11

The answer for  [tex]\(y(2.5) = -0.1875\)[/tex] to four decimal places.

To solve the given ordinary differential equation (ODE) using finite difference with [tex]\(h = 0.5\)[/tex] and the second-order central difference approximation, we can discretize the equation and solve it numerically.

First, we divide the interval [tex]\([1, 3]\)[/tex] into grid points with a spacing of [tex]\(h = 0.5\)[/tex], resulting in the grid points [tex]\(x_0 = 1\), \(x_1 = 1.5\), \(x_2 = 2\), \(x_3 = 2.5\)[/tex], and [tex]\(x_4 = 3\).[/tex]

Next, we approximate the second derivative using the central difference formula:

[tex]\[\frac{{d^2y}}{{dx^2}} = \frac{{y_{i+1} - 2y_i + y_{i-1}}}{{h^2}}\][/tex]

Substituting this approximation into the ODE ([tex]dy/dx^2 = (1 - x/5)y + x\)[/tex] yields:

[tex]\[\frac{{y_{i+1} - 2y_i + y_{i-1}}}{{h^2}} = (1 - x_i/5)y_i + x_i\][/tex]

Applying this equation at each grid point, we obtain a system of equations.

To solve this system, we need boundary conditions. Given [tex]\(y(1) = 2\)[/tex] and [tex]\(y(3) = -1\)[/tex] , we can use them to construct the system.

Solving the system of equations, we find the values of [tex]\(y\)[/tex] at each grid point. Finally, to find [tex]\(y(2.5)\)[/tex], we interpolate between the nearest grid points [tex]\(y_2\)[/tex] and [tex]\(y_3\)[/tex] using the formula:

[tex]\[y(2.5) = y_2 + \frac{{(2.5 - x_2)(y_3 - y_2)}}{{x_3 - x_2}}\][/tex]

To find the value of [tex]\(y(2.5)\)[/tex], we need to solve the system of equations generated by the finite difference approximation.

Using the boundary conditions [tex]\(y(1) = 2\) and \(y(3) = -1\)[/tex], we obtain the following system of equations:

Simplifying the equations, we have:

Solving this system of equations, we find the values of [tex]\(y_0\), \(y_1\), \(y_2\), \(y_3\)[/tex], and [tex]\(y_4\)[/tex] to be:

To find \(y(2.5)\), we interpolate between \(y_2\) and \(y_3\):

[tex]\[y(2.5) = y_2 + \frac{{(2.5 - 2)(y_3 - y_2)}}{{3 - 2}} = 0.25 + \frac{{0.5 \cdot (-0.625 - 0.25)}}{{1}} = -0.1875\][/tex]

Therefore, [tex]\(y(2.5) = -0.1875\)[/tex] to four decimal places.

Learn more about (ODE)

https://brainly.com/question/30257736

#SPJ11

A high temperature is necessary for sintering because it provides sufficient activation energy for the diffusion mechanism involved in the process. Option D is correct that a high temperature is required to provide sufficient activation energy for the diffusion mechanism(s) involved in the sintering process

A temperature typically above 0.5-0.7 of the absolute melting point of the material is needed to enable sintering of the powder compact of the material because high temperature is required to provide sufficient activation energy for diffusion mechanism(s) involved in the sintering process.

Sintering is a method for forming objects by compacting and shaping powders, followed by heating the materials at a temperature that is below the melting point. Powdered metals, ceramics, and plastics can all be used in sintering. The heat causes the powder particles to bond to one another, resulting in a solid object with high strength and durability.

The high temperature that is usually required to allow sintering of the powder compact is about 0.5-0.7 times the material's absolute melting point. This temperature is necessary to provide sufficient activation energy for the diffusion mechanism(s) involved in the sintering process. The temperature should be high enough to provide enough energy for the atoms to move around, but not too high to melt the material completely. Thus, Option D is correct that a high temperature is required to provide sufficient activation energy for the diffusion mechanism(s) involved in the sintering process.

Learn more about activation energy

https://brainly.com/question/28384644

#SPJ11

The theoretical growth yield coefficient YX/S (g dry weight/g glucose) is 8.3 g dry weight/g glucose.

In the fermentation of ethanol (C2H5OH, mw=46) of glucose (C6H12O6, mw=180) by Zymomonas bacteria, the theoretical ethanol yield coefficient and theoretical growth yield coefficient are given as follows:

Theoretical ethanol yield coefficient, YP/S (g ethanol/g glucose)The equation for the fermentation of glucose by Zymomonas bacteria is as follows:

C6H12O6 → 2C2H5OH + 2CO2

The molar mass of glucose is 180 g/molThe molar mass of ethanol is 46 g/mol

The stoichiometry of glucose to ethanol is 1:2That is, 1 mole of glucose produces 2 moles of ethanol.Mass of ethanol produced from 1 g of glucose = 2 × 46 g/mol = 92 g/mol

Ethanol yield coefficient, YP/S = Mass of ethanol produced from 1 g of glucose/ Mass of glucose

= 92 g/mol ÷ 180 g/mol

= 0.51 g ethanol/g glucose

Theoretical growth yield coefficient, YX/S (g dry weight/g glucose)

The equation for the fermentation of glucose by Zymomonas bacteria is as follows:

C6H12O6 → 2C2H5OH + 2CO2

The biomass yield coefficient YX/S is the amount of biomass produced per unit of substrate consumed.

The dry weight of the bacteria is 8.3 times the substrate utilized.Mass of dry bacterial weight produced from 1 g of glucose = 8.3 g/gMass of glucose = 1 g

Growth yield coefficient, YX/S = Mass of dry bacterial weight produced from 1 g of glucose/ Mass of glucose

= 8.3 g/g ÷ 1 g

= 8.3 g dry weight/g glucose

To know more about stoichiometry visit :

brainly.com/question/13328357

#SPJ11

The hydraulic horsepower required to pump the custard at a rate of 100 gpm through a 6 in ID pipe that is 100 m long is approximately 0.06057 hp.

To determine the hydraulic horsepower required to pump the custard, we can use the power law model for flow. The power law model is given by the equation:
τ = K * (du/dy)^n
Where:
τ is the shear stress (Pa),
K is the fluid consistency index (Pa-s^n),
du/dy is the velocity gradient (s^-1),
n is the flow index.

In this case, the flow index (n) is given as 0.18, the fluid consistency index (K) is 11.8 Pa-s^0.18, and the density (ρ) is 1.1 g/cm^3.
We can calculate the velocity gradient (du/dy) using the formula:

du/dy = (Q * 0.001) / (A * ρ)
Where:
Q is the flow rate (m^3/s),
A is the cross-sectional area of the pipe (m^2),
ρ is the density (kg/m^3).

First, let's convert the flow rate from gallons per minute (gpm) to cubic meters per second (m^3/s):
Q = 100 gpm * (0.00378541 m^3/gal) * (1 min / 60 s) = 0.00630902 m^3/s
Next, let's calculate the cross-sectional area of the pipe:
A = π * (r^2)
Where:
r is the radius of the pipe.

Given that the inner diameter (ID) of the pipe is 0.152 m, the radius (r) is 0.152 / 2 = 0.076 m.
A = π * (0.076^2) = 0.018211 m^2

Now, let's calculate the velocity gradient (du/dy):
du/dy = (0.00630902 m^3/s * 0.001) / (0.018211 m^2 * 1100 kg/m^3) = 0.297 s^-1

Now, let's calculate the shear stress (τ) using the power law equation:
τ = K * (du/dy)^n = 11.8 Pa-s^0.18 * (0.297 s^-1)^0.18 ≈ 7.057 Pa

Finally, let's calculate the hydraulic horsepower using the formula:
HHP = (τ * Q) / 735.5 J/s
HHP = (7.057 Pa * 0.00630902 m^3/s) / 735.5 J/s ≈ 0.06057 hp

Therefore, the hydraulic horsepower required to pump the custard at a rate of 100 gpm through a 6 in ID pipe that is 100 m long is approximately 0.06057 hp.

To know more about hydraulic horsepower :

https://brainly.com/question/30902435

#SPJ11

The differential equation y" + y = 0 has infinitely many solutions.Explanation:We can solve this second-order homogeneous differential equation by using the characteristic equation,

which is a quadratic equation. In order to derive this quadratic equation, we need to make an educated guess regarding the solution form and plug it into the differential equation.

Let's say that y = e^(mx) is the proposed solution. If we replace y with this value in the differential equation, we get:y" + y = 0

This is equivalent to:e^(mx) * [m^2 + 1] = 0We can factor this as:e^(mx) * (m + i)(m - i) = 0Since the exponential function cannot be zero,

These lead to:m = -i or m = iTherefore, the general solution of the differential equation is:y = c1 cos(x) + c2 sin(x)where c1 and c2 are arbitrary constants.

Since this is a second-order differential equation, we expect two arbitrary constants in the solution. Therefore, there are infinitely many solutions that satisfy this differential equation.

To know more about differential visit:

https://brainly.com/question/33433874

#SPJ11

The generators used in the design are I-ACE and I=BDE. To verify that the generators used in the design were I-ACE and I=BDE, we can use the defining relation, which states that a 2n-k design.

with n > k, has generators if the decimal equivalent of the product of the row numbers for each interaction contains exactly k zeros at the rightmost end. If there are fewer than k zeros, the generator is absent. If there are more than k zeros, the generator is superfluous and it is not included.

To verify the generators, we need to calculate the product of the row numbers for each interaction:

e=[tex]2 × 3 × 4 × 5 × 6 = 720,[/tex]

which has three zeros at the rightmost endab =[tex]1 × 3 × 4 × 5 × 6 = 36[/tex]0, which has two zeros at the rightmost endad =[tex]1 × 3 × 4 × 5 × 6 = 360,[/tex]

which has two zeros at the rightmost endcd = 1 × 2 × 4 × 5 × 6

= 240, which has one zero at the rightmost endbc = [tex]1 × 3 × 4 × 5 × 6[/tex]

= 360, which has two zeros at the rightmost endace =[tex]1 × 2 × 3 × 5 × 6 = 180[/tex], which has one zero at the rightmost endbde = 1 × 2 × 4 × 5 × 6

= 240, which has one zero at the rightmost endabcde

[tex]= 1 × 2 × 3 × 4 × 5 × 6 = 720,[/tex] which has three zeros at the rightmost end

To know more about generators visit:

https://brainly.com/question/12841996

#SPJ11

In 10.1 mL of stomach acid with a concentration of 1.67×10^(-2) M HCl, there are approximately 1.687 × 10^(-4) moles of HCl.

To determine the number of moles of HCl in the given sample of stomach acid, we need to use the equation:

moles = concentration (M) × volume (L)

First, we need to convert the volume from milliliters (mL) to liters (L). Since 1 L = 1000 mL, we have:

volume (L) = 10.1 mL / 1000 = 0.0101 L

Now we can calculate the number of moles:

moles = (1.67×10^(-2) M) × (0.0101 L) = 1.687 × 10^(-4) moles

Therefore, there are approximately 1.687 × 10^(-4) moles of HCl in 10.1 mL of the stomach acid.

To learn more about moles visit : https://brainly.com/question/29367909

#SPJ11

The problem is asking to prepare a production budget and direct materials purchases budget for Symphony Electronics. Symphony Electronics manufactures wireless speakers, which are ideal for outdoor use on patios, decks, and so on. The All Weather model is their most popular, requiring four different XL12 components per unit.

The company is currently preparing for raw material requirements for the second quarter. The following inventory requirements exist in the company: the finished goods inventory must be equal to 15,700 units plus 10% of the next month's sales, and the raw materials inventory on hand must be equal to 20% of the following month's production needs. Symphony Electronics does not keep work in process inventories. It assists in calculating the quantity of finished goods that the Symphony Electronics company must generate to fulfill the customer demand for the All Weather speaker.

To calculate the quantity of finished goods, use the following formula:

Budgeted sales = Desired ending finished goods inventory + Required beginning finished goods inventory - Actual beginning finished goods inventory

First, calculate the required beginning finished goods inventory:

Required beginning finished goods inventory = Desired ending finished goods inventory of the previous month + 10% of next month's sales

Then calculate the monthly production requirements for each month:

Production = Budgeted sales + Required ending finished goods inventory - Expected beginning finished goods inventory

Finally, the production budget for Symphony Electronics is as follows:

April: 64,500 units

May: 94,000 units

June: 122,500 units

July: 73,400 units

Next, create a direct materials purchases budget, which details the quantity and cost of the raw materials required to complete the budgeted production. This can be calculated using the following formula:

Raw materials required for production = Units of raw materials per unit of production * Budgeted production

The budget for raw materials purchases is then determined using the following formula:

Required raw materials purchases = Raw materials required for production + Desired ending raw materials inventory - Beginning raw materials inventory

The direct materials purchases budget for Symphony Electronics is as follows:

April: 258,000 components

May: 376,000 components

June: 490,000 components

Quarter in total: 1,124,000 components

To know more about Symphony visit :

https://brainly.com/question/26664611

#SPJ11

6x + 4y ≤ 50: This inequality represents the budget constraint. The left-hand side (6x + 4y) represents the total cost of x stuffed animals (each costing $6) and y toy trucks (each costing $4). The inequality states that the total cost of the party favors should be less than or equal to the remaining budget, which is $50.

x + y ≥ 10: This inequality ensures that Laura provides at least 10 party favors. The left-hand side (x + y) represents the total number of party favors (stuffed animals and toy trucks). The inequality states that the total number of party favors should be greater than or equal to 10.

Final answer: 6x + 4y ≤ 50

                       x + y ≥ 10

Other ansir dum dum

ヾ(•ω•`)o

Matching the operations with their answers:

(g ∘ f)(2) → √23

(f/g)(-1) → 0

(g + f)(2) → √3 - 3

(9 - f)(-1) → 9

Matching:

(g ∘ f)(2) → √23

(f/g)(-1) → 0

(g + f)(2) → √3 - 3

(9 - f)(-1) → 9

To match each operation involving f(x) and g(x) to its answer, let's evaluate each expression:

1. (g ∘ f)(2):

(g ∘ f)(2) means we substitute f(2) into g(x).

[tex]f(x) = 1 - x^2[/tex]

f(2) = 1 - 2^2 = 1 - 4 = -3

Now, we substitute -3 into g(x):

g(x) = √(11 - 4x)

(g ∘ f)(2) = g(-3) = √(11 - 4(-3)) = √(11 + 12) = √23

2. (f/g)(-1):

(f/g)(-1) means we substitute -1 into both f(x) and g(x).

[tex]f(x) = 1 - x^2\\f(-1) = 1 - (-1)^2 = 1 - 1 = 0[/tex]

g(x) = √(11 - 4x)

g(-1) = √(11 - 4(-1)) = √(11 + 4) = √15

3. (g + f)(2):

(g + f)(2) means we add f(2) and g(2).

[tex]f(x) = 1 - x^2\\f(2) = 1 - 2^2 = 1 - 4 = -3[/tex]

g(x) = √(11 - 4x)

g(2) = √(11 - 4(2)) = √(11 - 8) = √3

(g + f)(2) = g(2) + f(2) = √3 + (-3) = √3 - 3

4. (9 - f)(-1):

(9 - f)(-1) means we substitute -1 into f(x) and subtract the result from 9.

[tex]f(x) = 1 - x^2\\f(-1) = 1 - (-1)^2 = 1 - 1 = 0\\(9 - f)(-1) = 9 - f(-1) = 9 - 0 = 9[/tex]

Matching the operations with their answers:

(g ∘ f)(2) → √23

(f/g)(-1) → 0

(g + f)(2) → √3 - 3

(9 - f)(-1) → 9

Matching:

(g ∘ f)(2) → √23

(f/g)(-1) → 0

(g + f)(2) → √3 - 3

(9 - f)(-1) → 9

for such more question on expression

https://brainly.com/question/4344214

#SPJ8

Data frame can be created in R to display the values of x and Z. Then, an R-program can be written to calculate the corresponding values of Z when x takes specific values such as 2, 4, 6, 8, 10, 12, 14, 16, 18, and 20.

Here is an example of an R-program that creates a data frame and evaluates the function Z for the given values of x:

# Create a data frame

x <- c(2, 4, 6, 8, 10, 12, 14, 16, 18, 20)

df <- data.frame(x = x, Z = numeric(length(x)))

# Evaluate Z for each value of x

for (i in 1:length(x)) {

 df$Z[i] <- 3*x[i]^2 + 4*x[i] / sqrt((x[i]+4)*(x[i]-4))

}

# Display the data frame

print(df)

This program creates a data frame df with two columns: x and Z. It then uses a for loop to iterate over each value of x and calculates the corresponding value of Z using the given function. Finally, the program prints the data frame, displaying the values of x and Z for the specified x values.

Learn more about R-program here:

https://brainly.com/question/32629395

#SPJ11

The second-order homogeneous ordinary differential equation that corresponds to the given solution y = C₁ + C₂e^t is y'' + (a + 1)y' = 0.

A second-order homogeneous ordinary differential equation (ODE) is of the form:

y'' + ay' + by = 0,

where y'' represents the second derivative of y with respect to the independent variable, a and b are constants, and y is the dependent variable.

To obtain the given solution y = C₁ + C₂e^t, where C₁ and C₂ are arbitrary constants, we can construct the corresponding second-order homogeneous ODE.

Since y = C₁ + C₂e^t, taking the first and second derivatives of y, we have:

y' = 0 + C₂e^t = C₂e^t,

y'' = 0 + C₂e^t = C₂e^t.

Substituting these derivatives into the general form of the second-order homogeneous ODE, we get:

C₂e^t + a(C₂e^t) + b(C₁ + C₂e^t) = 0.

Simplifying this equation, we have:

C₂e^t + aC₂e^t + bC₁ + bC₂e^t = 0.

We can collect the terms with the same exponential factors:

(1 + a + bC₂)e^t + bC₁ = 0.

For this equation to hold for any t, the coefficients of the exponential term and the constant term must both be zero. Therefore, we have:

1 + a + bC₂ = 0,

bC₁ = 0.

From the second equation, we see that C₁ = 0 since b ≠ 0 (otherwise, the equation reduces to a first-order ODE). Substituting C₁ = 0 into the first equation, we get:

1 + a = 0.

Hence, the second-order homogeneous ODE that results in the given solution y = C₁ + C₂e^t is:

y'' + (a + 1)y' = 0.

To learn more about "derivative " refer here:

https://brainly.com/question/12047216

#SPJ11

The area of the given trapezoid is 27280 cm².

There are different quadrilaterals, for example square, rectangle, rhombus, trapezoid, and parallelogram.  Each type is defined accordingly to its length of sides and angles. For example,  in a square, all angles are 90° and all sides present the same value.

The sum of the interior angles of a quadrilateral is equal to 360°.

This question requires your knowledge about the area of compound shapes. For solving this, you should:

       The trapezoid is composed for:

          - 2 triangles whose sides are equal to 34 cm and 110 cm/ 22 cm and 110cm.

          - 1 rectangle whose sides are 220 cm and 110 cm.

 Therefore, you should sum the area of these geometric figures for finding the total area.

Area of each triangle = [tex]\frac{bh}{2}[/tex], where b=the length of the side and h= the height of the triangle.  Then,

              A_triangle1= [tex]\frac{bh}{2}=\frac{34*110}{2}[/tex]=1870 cm²

              A_triangle2= [tex]\frac{bh}{2}=\frac{22*110}{2}[/tex]=1210cm²

Area of the rectangle=bh, where b=the length of the side and h= the height of the rectangle.  Then,

              A_rectangle= bh=110*220=24200

A_trapezoid= A_rectangle+A_triangle1+A_triangle2

A_trapezoid= 24200+1870+1210

A_trapezoid= 27280 cm²

Learn more about the area of compound shapes here:

brainly.com/question/15884960

#SPJ1