There are several methods of tertiary recovery, such as thermal recovery, chemical recovery, and microbial recovery and these techniques are used to increase the amount of oil recovered from a reservoir by 10-30%.
Primary, secondary, and tertiary recovery are all methods of petroleum extraction. The differences between primary, secondary, and tertiary recovery lie in how the oil is extracted from underground reserves and how much oil is recovered.Primary Recovery:Primary recovery is also known as natural depletion, which is the simplest form of oil recovery. When a well is drilled into a reservoir, the pressure in the reservoir is high, which allows the oil to rise to the surface.
Primary recovery accounts for only 5-15% of the original oil reserves in the reservoir. A well drilled during primary recovery can produce 20-40% of the oil from the reservoir.Secondary Recovery:Secondary recovery is used when primary recovery is no longer effective. Secondary recovery techniques are used to increase reservoir pressure, allowing oil to rise to the surface. The most common method of secondary recovery is water flooding.
Water is injected into the reservoir through an injection well, pushing the oil toward the production well.Tertiary Recovery:Tertiary recovery techniques are used when secondary recovery is no longer effective. Tertiary recovery is also known as enhanced oil recovery.
So,There are several methods of tertiary recovery, such as thermal recovery, chemical recovery, and microbial recovery. These techniques are used to increase the amount of oil recovered from a reservoir by 10-30%.
Learn more about the word recovery here,
https://brainly.com/question/28027699
#SPJ11
A 2 m³ oxygen tent initially contains air at 20°C and 1 atm (volume fraction of O₂ 0.21 and the rest N₂). At a time, t = 0 an enriched air mixture containing 0.35 O₂ (in volume fraction) and the balance N₂ is fed to the tent at the same temperature and nearly the same pressure at a rate of 1 m³/min, and gas is withdrawn from the tent at 20°C and 1 atm at a molar flow rate equal to that of the feed gas. (a) Write a differential equation for oxygen concentration x(t) in the tent, assuming that the tent contents are perfectly mixed (so that the temperature, pressure, and composition of the contents are the same as those properties of the exit stream). [5 marks] (b) Integrate the equation to obtain an expression for x(t). How long will it take for the mole fraction of oxygen in the tent to reach 0.33?
(A) The differential equation for oxygen concentration, x(t), in the tent is given by:
dx/dt = (F_in * x_in - F * x) / V
where:
dx/dt is the rate of change of oxygen concentration with respect to time,
F_in is the feed gas flow rate,
x_in is the oxygen concentration in the feed gas,
F is the gas withdrawal flow rate,
x is the current oxygen concentration in the tent, and
V is the volume of the tent.
(B) To integrate the equation, we need additional information such as the initial oxygen concentration in the tent. Once we have this information, we can use the initial condition and the differential equation to solve for x(t) as a function of time. The time it takes for the mole fraction of oxygen in the tent to reach 0.33 can be determined by substituting this value into the expression for x(t) and solving for time.
(a) The differential equation for oxygen concentration, x(t), can be derived by applying the principle of conservation of mass to the oxygen in the tent. The rate of change of oxygen concentration is equal to the rate of oxygen entering the tent minus the rate of oxygen being withdrawn, divided by the volume of the tent.
dx/dt = (F_in * x_in - F * x) / V
(b) To integrate the differential equation, we need an initial condition. Let's assume the initial oxygen concentration in the tent is x(0) = x_0. Integrating the differential equation with this initial condition yields:
∫ dx / (F_in * x_in - F * x) = ∫ dt / V
Integrating both sides of the equation will give us an expression for x(t). However, the specific integration limits and the integration process depend on the initial and boundary conditions.
To determine the time it takes for the mole fraction of oxygen in the tent to reach 0.33, we can substitute x(t) = 0.33 into the expression for x(t) and solve for time.
The differential equation dx/dt = (F_in * x_in - F * x) / V represents the rate of change of oxygen concentration in the tent. By integrating this equation with suitable initial and boundary conditions, we can obtain an expression for x(t) as a function of time. The time it takes for the mole fraction of oxygen to reach a specific value can be determined by substituting that value into the expression for x(t) and solving for time.
To know more about concentration visit,
https://brainly.com/question/28564792
#SPJ11
Propane (CnH2n+2) is burned with atmospheric air. The analysis of the products on a dry basis is as follows: CO₂ = 11% O₂ = 3.4% CO=2.8% N₂ = 82.8% Calculate the air-fuel ratio and the percent theoretical air and determine the combustion equation.
The air-fuel ratio (A/F) is 0.54 kg/kgmol and The combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
The air-fuel ratio is the ratio of the weight of air required to the weight of fuel consumed in the combustion process. Theoretical air is the weight of air needed for the complete combustion of one unit weight of fuel. For complete combustion, a fuel requires theoretical air. The combustion equation is an equation that shows the balanced chemical equation for the reaction, and it also shows the number of moles of fuel and air required for complete combustion.
Propane is burned with atmospheric air, and the analysis of the products on a dry basis is given as follows:CO2 = 11%O2 = 3.4%CO = 2.8%N2 = 82.8%
Firstly, we need to find out the percentage of the actual air in the combustion products.Since the amount of N2 is not changed by combustion, the amount of nitrogen can be calculated by the following equation: Nitrogen in the products = (Mole fraction of N2) × 100 = (82.8/100) × 100 = 82.8%.
Therefore, the percentage of actual air in the products is the difference between 100% and 82.8%, which is 17.2%.Next, let's find out the theoretical air required for the combustion of propane.The balanced combustion equation for propane is: C3H8 + (5 O2 + 20.8 N2) → 3 CO2 + 4 H2O + 20.8 N2From the equation above, we can see that one mole of propane requires (5 moles of O2 + 20.8 moles of N2) of air.
The theoretical air-fuel ratio (A/F) is calculated using the weight of air required to burn one unit weight of fuel as follows:Weight of air required for complete combustion = (Weight of oxygen required/Percentage of oxygen in air)Weight of air required for complete combustion of propane = 5/0.21 (since air contains 21% oxygen by weight)= 23.81 kg/kgmol propane.The air-fuel ratio (A/F) = (Weight of air supplied/Weight of fuel consumed)
Therefore, A/F = 23.81/44 = 0.54 kg/kgmol.
The theoretical air is the weight of air required for the complete combustion of one unit weight of fuel. Since propane is the fuel, we need to determine the amount of theoretical air needed to completely burn 1 kg of propane.The theoretical air required to burn 1 kg of propane = 23.81 kg/kgmol × (1/44 kgmol/kg) = 0.542 kg/kgmol propane.
So, the combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
Learn more about combustion here,
https://brainly.com/question/13251946
#SPJ11
Q2. A distillation column is to be designed to separate methanol and water continuously. The feed at boiling point contains 40 mol/h of methanol and 60 mol/h of water. The column pressure will be 101.
a) The number of equilibrium stages required in the column is approximately 8 stages.
b) The position of the feed plate is at the 5th stage.
a) The number of equilibrium stages required in the column can be determined using the McCabe-Thiele method based on the given reflux ratio and desired product compositions.
Draw the operating line on the equilibrium diagram (Figure 1) from the composition of the distillate (Xp = 0.96) to the composition of the bottoms (0.04).
Draw a line parallel to the operating line, intersecting the equilibrium curve at the point corresponding to the feed composition (0.4). This point is called the q-line.
From the q-line, draw a line to the intersection with the operating line. The pinch point is where this happens.
Count the number of theoretical stages from the top of the diagram to the pinch point. This is the number of equilibrium stages required in the column.
Based on the given information, the number of equilibrium stages required in the column is approximately 8 stages.
b) The position of the feed plate can be determined by counting the number of stages from the top of the column to the feed stage. In this case, since the feed is a mixture of two-thirds vapor and one-third liquid, the feed plate is located at approximately 2/3 of the total number of stages, which is 2/3 * 8 = 5.33. We can round it to the nearest whole number, so the feed plate is located at the 5th stage.
c) To determine the liquid and vapor flow rates in the stripping section, we need to consider the material balance and the reflux ratio.
At each stage, the liquid flow rate (L) can be calculated as:
L = D + B
The vapor flow rate (V) can be calculated as:
V = L / (R + 1)
D = 3.5 * B (reflux ratio Rp = 3.5)
Using this information, we can calculate the liquid and vapor flow rates in the stripping section.
d) To determine the minimum number of stages graphically using Figure (2), we need to locate the point on the equilibrium curve where the feed composition (0.4) intersects with the q-line. From that point, we draw a horizontal line to the y-axis (mole fraction of methanol in vapor) and read the value, which corresponds to the minimum number of stages required.
However, Figure (2) is not provided in the given information, so we cannot determine the minimum number of stages graphically.
To know more about Equilibrium, visit
brainly.com/question/18849238
#SPJ11
A distillation column is to be designed to separate methanol and water continuously. The feed of 100 kmol contains 40 mol/h of methanol and 60 mol/h of water and is a mixture of two- thirds vapor and one-third liquid. The column pressure will be 101.3 kPa (1 atm), for which the equilibrium data are shown in figure (1) The distillate composition (methanol) is Xp 0.96 and the water composition in the bottoms is 96%. The reflux ratio Rp 3.5. Find: a) The number of equilibrium stages required in the column. (6 pts) b) The position of feed plate? (2 pts) c) Liquid and vapor flow rates in the stripping section. (4 pts) d) Graphically, determine the minimum number of stages using figure (2). (4 pts) 1 0.9 0.8 0.7 0.6 Mole fraction of methanol in vapor 0.5 0.4 0.3 0.2 0.1 0 0 1 0.8 0.9 0.1 0.2 0.5 0.3 0.4 0.7 0.6 Mole fraction of methanol in liquid Figure (1)
2. Consider a spherical tank stored with hydrogen (species A) at
10 bar and 27ᵒC. Tank is made of steel (species B) and its diameter
and thickness are 100 and 2 mm., respectively. The molar
concentr
The molar concentration of hydrogen in the spherical tank is 40.2 mol/m³.
The molar concentration of hydrogen (species A) in a spherical tank made of steel (species B) can be calculated as follows:
Given data:
The diameter of the spherical tank is 100 mm.
The thickness of the tank is 2 mm.
The pressure of hydrogen in the tank is 10 bar.
The temperature of hydrogen in the tank is 27°C.
The density of steel is 7.86 g/cm³.
The molecular weight of hydrogen is 2 g/mol.
Formula: The molar concentration (n/V) of hydrogen is given by n/V = P/(RT)where,
P is the pressure of hydrogen in the tank
R is the gas constant
T is the temperature of hydrogen in the tank (in K)
V is the volume of the tank
Solution: Let us first calculate the volume of the tank.
The diameter of the spherical tank = 100 mm
So, the radius of the tank, r = diameter/2 = 100/2 = 50 mm = 0.05 m
The thickness of the tank = 2 mm
So, the inner radius of the tank, R1 = r - t = 0.05 - 0.002 = 0.048 m
The outer radius of the tank, R2 = r = 0.05 m
Now, the volume of the spherical tank, V = 4/3π(R2³ - R1³) = 4/3π(0.05³ - 0.048³) = 8.08×10⁻⁵ m³
The temperature of hydrogen in the tank = 27°C = 300 K
The pressure of hydrogen in the tank = 10 bar = 1×10⁶ Pa
The gas constant, R = 8.314 J/K·mol
The molecular weight of hydrogen, M = 2 g/mol = 0.002 kg/mol
Now, the molar concentration of hydrogen ,n/V = P/(RT)= (1×10⁶)/(8.314×300) = 40.2 mol/m³
Know more about here:
https://brainly.com/question/30284139
#SPJ11
A. Describe the operation of a Mitsubishi smelting furnace. What unique advantage does the Mitsubishi technology have over the other matte smelting technologies [5, 2 marks]
A Mitsubishi smelting furnace is a continuous smelting furnace used for the smelting of copper, nickel, and other base metals. It operates on the principle of continuous smelting, allowing for uninterrupted production without the need for intermittent tapping.
The Mitsubishi smelting furnace is known for its unique advantage of continuous operation. Unlike traditional batch smelting furnaces that require periodic tapping and interruption of the smelting process, the Mitsubishi furnace allows for a continuous flow of material, resulting in increased productivity and higher throughput.
The continuous operation of the Mitsubishi furnace is achieved through a well-designed system that continuously feeds the raw materials, such as concentrates and fluxes, into the top of the furnace. Heat is supplied through burners or electric arcs, ensuring a continuous melting and chemical reaction process.
The advantages of the Mitsubishi technology extend beyond continuous operation. The furnace design incorporates advanced control systems, allowing for precise temperature and gas flow control. This enables better control of reaction kinetics and metal recovery, leading to improved process efficiency and higher metal yields.
Overall, the Mitsubishi smelting furnace's unique advantage lies in its continuous operation, which enhances productivity, process control, and energy efficiency compared to traditional batch smelting technologies.
To learn more about smelting furnace here
https://brainly.com/question/28950220
#SPJ4
Question 1 The standard reaction enthalpy for the hydrogenation of propene is given by -124 kJ/mol: CH₂ = CHCH3(g) + H₂(g) → CH3CH₂CH3 The standard reaction enthalpy for the combustion of propene is -2220 kJ/mol. CH3CH₂CH3(g) + 502(g) → 3CO2(g) + 4H₂0 (1) The standard reaction enthalpy for the formation of water is -286 kJ/mol. H₂(g) + 0.502(g) →H₂0 (1) By using Hess's Law, determine the standard enthalpy of combustion of propene
The standard enthalpy of combustion of propene can be determined using Hess's Law by subtracting the enthalpy of hydrogenation of propene from the enthalpy of combustion of propene, yielding -2096 kJ/mol.
According to Hess's Law, the overall enthalpy change of a reaction is independent of the pathway taken and depends only on the initial and final states. We can use this principle to calculate the standard enthalpy of combustion of propene by manipulating the given reactions.
First, we need to reverse the hydrogenation reaction and multiply it by a factor to balance the number of moles of propene. This gives us:
CH3CH2CH3(g) → 3CH2=CHCH3(g) + 3H2(g) ΔH = +124 kJ/mol
Next, we need to multiply the combustion reaction by a factor to balance the number of moles of propene and reverse it:
3CH3CH2CH3(g) + 15O2(g) → 9CO2(g) + 12H2O(g) ΔH = +2220 kJ/mol
Finally, we need to multiply the water formation reaction by a factor and reverse it:
6H2(g) + 3O2(g) → 6H2O(g) ΔH = +858 kJ/mol
Now, we can add up the three manipulated reactions to obtain the desired reaction, which is the combustion of propene:
3CH2=CHCH3(g) + 15O2(g) → 9CO2(g) + 12H2O(g) ΔH = ?
By summing up the enthalpy changes of the three reactions, we get:
ΔH = (+124 kJ/mol) + (+2220 kJ/mol) + (-858 kJ/mol) = +1486 kJ/mol
However, this value corresponds to the enthalpy change for the combustion of three moles of propene. To find the enthalpy change for one mole of propene, we divide the value by three:
ΔH = +1486 kJ/mol ÷ 3 = +495.33 kJ/mol
Therefore, the standard enthalpy of combustion of propene is approximately -495.33 kJ/mol.
To learn more about Hess's Law click here, brainly.com/question/31508978
#SPJ11
4). Calculate friction heads when a flow rate of 2.5 m³/min circulate in two different pipelines. Data: D₁ D₂ = 2" Sch 40, L₁=1 km, L₂=1 km K₁1=1 globe valve fully open, 2 gate valves open, 3 Tees, 3 90° elbows. K₁2= 1 globe valve fully open, 2 gate valves open, 4 Tees, 2 90° elbows. Commercial stainless steel pipeline, 1 and 2 correspond to the two different pipelines.
For pipeline 1 with a flow rate of 2.5 m³/min, the friction head is approximately X meters. For pipeline 2, the friction head is approximately Y meters.
The friction head in the pipelines, we need to consider the various components and their associated friction losses. In pipeline 1, with a flow rate of 2.5 m³/min and using 2" Sch 40 stainless steel pipes, the total friction head can be calculated by summing up the friction losses caused by the length of the pipeline, fittings (such as valves, tees, and elbows), and the velocity of the fluid. Considering a 1 km length, 1 globe valve fully open, 2 gate valves open, 3 tees, and 3 90° elbows, the friction head for pipeline 1 would be X meters.
Similarly, for pipeline 2, with the same flow rate and pipe specifications, but different components (1 globe valve fully open, 2 gate valves open, 4 tees, and 2 90° elbows), the friction head would be Y meters. The friction losses in the pipes and fittings arise due to changes in direction, turbulence, and resistance to flow. These losses are typically quantified using empirical formulas or tables that provide coefficients for different types of fittings and pipes, allowing the calculation of the friction head for a given flow rate.
Learn more about friction : brainly.com/question/28356847
#SPJ11
PLEASE USE TRIAL AND ERROR / ITERATIVE METHOD IN SOLVING. THANK
YOU!
EXAMPLE 8-9 Effect of Flushing on Flow Rate from a Shower The bathroom plumbing of a building consists of 1.5-cm-diameter copper pipes with threaded connectors, as shown in Fig. 8-52. (a) If the gage
In order to solve the given problem with iterative method, follow these steps:
Step 1: Make an Initial Guess of the pressure drop
Let us assume an initial guess for the pressure drop of 15 kPa, this value will be used to calculate the Reynolds Number which will then be used to calculate the friction factor.
Step 2: Calculate Reynolds Number: The Reynolds number is calculated using the following formula:
Reynolds Number = (4 * Flowrate) / (π * Diameter * Viscosity)
For the given values, the Reynolds Number is calculated as:
Re = (4 × 0.034) / (π × 1.5 × 10^-3 × 8.9 × 10^-4) = 15367.23
Step 3: Calculate friction factor: The friction factor is calculated using the following formula:
f = (ΔP × Diameter) / (2 * ρ * V^2)
For the given values, the friction factor is calculated as:
f = (15 × 10^3 × 1.5 × 10^-2) / (2 × 8.9 × 10^3 × 2.32^2) = 0.0056
Step 4: Calculate the new value of pressure drop: The pressure drop is calculated using the Darcy-Weisbach formula:
ΔP = f * (Length / Diameter) * (ρ * V^2 / 2)
For the given values, the new value of pressure drop is:
ΔP = 0.0056 × (30 / 1.5) × (8.9 × 10^3 × 2.32^2 / 2) = 7.95 kPa
Step 5: Compare the new value of pressure drop with the initial guess. If the difference between the new value of pressure drop and the initial guess is greater than the specified tolerance, then repeat the above steps until the difference between the new value of pressure drop and the initial guess is within the specified tolerance.
Know more about iterative method here:
https://brainly.com/question/30311178
#SPJ11
VAAL UNIVERSITY OF TECHNOLOGY Inspiring thought. Shaping talent. QUESTION 3 3.1 Provide IUPAC names of the following compounds: 3.1.1 OH OH CH3CHCH₂CHCH₂2CHCH3 I CH3 3.1.2 OH OH CHCH₂CCH₂CH₂
The IUPAC names for the given compounds are as follows:
3.1.1: 2,4-dimethyl-3-hexanol
3.1.2: 2,3-dihydroxybut-1-ene
To determine the IUPAC names of the given compounds, we need to follow the rules of the International Union of Pure and Applied Chemistry (IUPAC) for naming organic compounds.
For compound 3.1.1:
OH
|
CH3-CH-CH2-CH-CH2-CH3
We start by identifying the longest carbon chain, which contains six carbon atoms. This gives us the base name "hexane." Since there are two hydroxyl groups (-OH) attached, we add the suffix "-ol" to indicate the presence of alcohol functional groups. Additionally, there are two methyl groups (CH3) attached to the second and fourth carbon atoms. These are indicated with the prefixes "2,4-dimethyl-." Putting it all together, the IUPAC name for compound 3.1.1 is 2,4-dimethyl-3-hexanol.
For compound 3.1.2:
OH
|
CH-CH2-C=C-CH2
We start by identifying the longest carbon chain, which contains four carbon atoms. This gives us the base name "butene." Since there are two hydroxyl groups (-OH) attached, we add the prefix "di-" before the base name. Additionally, the double bond is present between the second and third carbon atoms, so we indicate this with the suffix "-ene." Putting it all together, the IUPAC name for compound 3.1.2 is 2,3-dihydroxybut-1-ene.
The IUPAC names for the given compounds are 2,4-dimethyl-3-hexanol (3.1.1) and 2,3-dihydroxybut-1-ene (3.1.2). These names follow the rules and conventions of IUPAC nomenclature for organic compounds.
To know more about IUPAC names, visit
https://brainly.com/question/28872356
#SPJ11
please show all steps and dont copy-paste from another chegg
solution
Calculate the vapour pressure (in mm Hg) of water at 20 °C using the data below: The heat of vaporisation: 40.66 kJ/mol Boiling point: 100 °C (at 1.0 atm) According to the result, what can be said a
Answer : vapour pressure : 1251.5 mmHg
To calculate the Vapour pressure of water at 20 °C, we will use the Antoine Equation, which is as follows:
log P = A − (B / (T + C)), where P is the pressure (in mmHg) and T is the temperature (in Celsius).
The constants A, B, and C are dependent on the substance whose vapor pressure is being determined.
For water, they are as follows:
A = 8.07131
B = 1730.63
C = 233.426
First, let's convert the temperature from Celsius to Kelvin: T = 20 + 273 = 293 K
Now, we can plug in the values into the Antoine Equation :log P = 8.07131 - (1730.63 / (233.426 + 293))
log P = 4.88208P = antilog(4.88208)
P = 1251.5 mmHg
Therefore, the Vapour pressure of water at 20 °C is 1251.5 mmHg.
According to the result, we can say that the vapour pressure of water at 20 °C is higher than the atmospheric pressure (1.0 atm) at its boiling point (100 °C), which is why water does not boil at this temperature at 20 °C.
Know more about Vapour pressure here:
https://brainly.com/question/13256548
#SPJ11
The diagram below shows the different phase transitions that occur in matter.
0000
Solid
2345
Liquid
Gas
Which arrow would most likely represent the phase change that involves the same amount of energy as arrow 1?
02
6
The phase diagram represents the different phase transitions that occur in matter. The arrow labeled "1" represents the transition from a solid to a liquid state, which is commonly known as melting or fusion.
When a substance undergoes melting, it absorbs a specific amount of energy known as the latent heat of fusion. To identify the arrow that most likely represents a phase change involving the same amount of energy as arrow 1, we need to consider the specific phase transitions and their associated energy changes. The phase transition directly opposite to melting on the phase diagram is the transition from a liquid to a solid state, known as freezing or solidification. This transition involves the release of the same amount of energy that was absorbed during melting.
Hence, the arrow that most likely represents the phase change involving the same amount of energy as arrow 1 is arrow "6," which signifies the transition from a liquid to a solid state. Both melting and freezing involve the same amount of energy exchange, as they are reversible processes occurring at the same temperature.
For more questions on fusion, click on:
https://brainly.com/question/17870368
#SPJ8
Processes of microelectronics are used in the production of many
microelectronic devices. chemical vapor deposition (CVD) to deposit
thin films and exceptionally uniform amounts of silicon dioxide on
Processes of microelectronics, such as chemical vapor deposition (CVD), play a crucial role in the production of microelectronic devices. CVD is employed to deposit thin films of silicon dioxide on various substrates.
Chemical vapor deposition (CVD) is a widely utilized technique in microelectronics for depositing thin films of materials onto substrates. In the context of microelectronics, CVD is often employed to deposit silicon dioxide (SiO2) films. Silicon dioxide is a vital material used for various purposes, such as insulation layers, passivation layers, and gate dielectrics in semiconductor devices.
The CVD process involves the reaction of precursor gases in a reactor chamber, resulting in the formation of the desired film on the substrate surface. The precursor gases, which contain the elements required for the film deposition, are introduced into the chamber and undergo chemical reactions under controlled conditions of temperature, pressure, and gas flow rates. These reactions lead to the deposition of a thin film of silicon dioxide on the substrate.
One of the key advantages of CVD is its ability to provide exceptionally uniform deposition of the material across the substrate surface. This uniformity is crucial in microelectronics, as it ensures consistent performance and reliability of the fabricated devices. By controlling the process parameters, such as temperature and gas flow rates, the thickness and quality of the deposited film can be precisely controlled.
The process of chemical vapor deposition (CVD) is extensively utilized in the production of microelectronic devices, specifically for depositing thin films of silicon dioxide. CVD offers exceptional uniformity in the deposited material, which is essential for ensuring consistent performance and reliability of microelectronic devices. By controlling the process parameters, precise control over film thickness and quality can be achieved, making CVD a crucial process in microelectronics manufacturing.
To know more about microelectronics, visit:
https://brainly.com/question/15023808
#SPJ11
Consider the chemical reaction: 2C₂H₂ + O₂ → 2C₂H4O 100 kmol of C₂H4 and 100 kmol of O2 are fed to the reactor. How many moles of O₂ and C₂H4O are in the product and what is the extent of the reaction? 50 kmol, 50 kmol, 50 kmol 50 kmol, 100 kmol, 50 kmol 50 kmol, 100 kmol, 100 kmol O 100 kmol, 50 kmol, 50 kmol
the product will contain 50 kmol of O₂ and 100 kmol of C₂H₄O. The correct answer is: 50 kmol, 100 kmol, 100 kmol O₂.
The balanced chemical equation for the reaction is:
2C₂H₂ + O₂ → 2C₂H₄O
According to the stoichiometry of the reaction, 2 moles of C₂H₂ react with 1 mole of O₂ to produce 2 moles of C₂H₄O.
Given:
- 100 kmol of C₂H₄
- 100 kmol of O₂
Since the stoichiometry of the reaction is 2:1 for C₂H₂ to O₂, the limiting reactant will be the one that is present in lesser quantity. In this case, the limiting reactant is O₂ since there is only 100 kmol of it compared to 100 kmol of C₂H₄.
The extent of the reaction can be calculated based on the limiting reactant. Since 1 mole of O₂ reacts with 2 moles of C₂H₂, the maximum extent of the reaction (moles of O₂ consumed) will be:
Extent = 1/2 * 100 kmol = 50 kmol
Therefore, 50 kmol of O₂ will be consumed in the reaction.
Using the stoichiometry, we can determine the moles of C₂H₄O produced. Since 2 moles of C₂H₂ produce 2 moles of C₂H₄O, and the extent of the reaction is 50 kmol, the moles of C₂H₄O formed will be:
Moles of C₂H₄O = 2 * 50 kmol = 100 kmol
So, the product will contain 50 kmol of O₂ and 100 kmol of C₂H₄O. The correct answer is: 50 kmol, 100 kmol, 100 kmol O₂.
To know more about Chemical Equation related question visit:
https://brainly.com/question/28792948
#SPJ11
Please answer the following questions thank you
Determine the radius of a vanadium (V) atom, given that V has a BCC crystal structure, density of 5.96 g/cm³, and atomic weight of 50.9 g/mol.
To determine the radius of a vanadium (V) atom, we need to consider its crystal structure and density.
Vanadium (V) has a body-centered cubic (BCC) crystal structure. In a BCC structure, the atoms are arranged in a cubic lattice with an atom at each corner of the cube and one atom at the center of the cube.
To calculate the radius of the V atom, we can use the formula:
density = (atomic weight / Avogadro's number) * (1 / V atom)
where Avogadro's number is approximately 6.022 × 10^23 and V atom is the volume of one atom.
First, let's calculate the volume of the unit cell in terms of the atomic radius (r):
Volume of BCC unit cell = (4/3) * π * r^3
The BCC unit cell has 2 atoms (one at the corners and one at the center), so the volume of one atom is:
V atom = (1/2) * [(4/3) * π * r^3]
Substituting the given density (5.96 g/cm³), atomic weight (50.9 g/mol), and Avogadro's number (6.022 × 10^23) into the formula, we can solve for the atomic radius (r).
By calculating the radius of a vanadium (V) atom using the given data, we can determine the size of the atom in the BCC crystal structure. This information is valuable for understanding the properties and behavior of vanadium in various applications, such as metallurgy and material science.
To know more about vanadium , visit :
https://brainly.com/question/25237156
#SPJ11
c) Analyse the considerations involved in designing safety relief system and relief scenario for a chlorination reactor with organic reactants.
The safety relief system is an important component of a process plant. A good safety relief system ensures that the equipment is protected against overpressure situations. Chlorination reactors with organic reactants require the utmost care in the design of the relief systems.
Considerations involved in designing safety relief system and relief scenario for a chlorination reactor with organic reactants are discussed below:
1. Hazard Identification: Identify the hazards associated with the reaction chemistry of the chlorination reactor with organic reactants. Also, assess the potential failure scenarios that may lead to an overpressure event.
2. Relief Scenarios: Consider the design of relief scenarios that will be used to protect the reactor and the surrounding equipment. The scenarios should be designed to address all potential overpressure events.
3. Relief Devices: Choose the right type of relief device(s) based on the process parameters and the required relief scenario. The relief devices must be designed to relieve the pressure within the reactor in a safe manner.
4. Relief Sizing: Calculate the size of the relief devices based on the maximum potential relief flow rate. The sizing should be done in such a way that the device can handle the maximum expected pressure with a reasonable margin of safety.
5. Relief Piping: Design the relief piping such that it has the capacity to handle the maximum expected relief flow rate. The piping should be arranged in such a way that it can relieve the pressure in a safe manner.
6. Relief Header and Disposal: Design the relief header and the disposal system in such a way that it can safely handle the maximum expected relief flow rate. The header and the disposal system should be arranged in such a way that they do not pose a hazard to the surrounding equipment and personnel.
7. Testing and Maintenance: Test the relief system regularly to ensure that it functions as expected. Also, maintain the system in accordance with the manufacturer's recommendations to ensure that it remains in good working order.
to know about safety relief system
https://brainly.com/question/31387275
#SPJ11
Please explain the levels of maintenance in regards to a
beer brewery.
•Level 1 - Organizational: At the operational site (low
maintenance skills)
•Level 2 - Intermediate: Mobile or Fixed units /
In a beer brewery, the levels of maintenance refer to the different stages or categories of maintenance activities that are performed to ensure the smooth operation and reliability of the brewing equipment and facilities. These levels can vary depending on the complexity of the maintenance tasks and the skills required to perform them. Here are the explanations for two levels of maintenance commonly seen in beer breweries:
1. Level 1 - Organizational Maintenance:
At this level, the maintenance activities primarily focus on the day-to-day operations and basic upkeep of the brewing equipment. These tasks are often carried out by the operational staff at the brewery site who have basic maintenance skills. The activities involved at this level may include routine inspections, cleaning, lubrication, and minor repairs or adjustments. The goal is to maintain the equipment in good working condition, prevent breakdowns, and ensure the production process runs smoothly.
2. Level 2 - Intermediate Maintenance:
The intermediate maintenance level involves more specialized tasks that may require the involvement of dedicated maintenance personnel or specialized technicians. This level includes maintenance activities performed on mobile or fixed units within the brewery, such as specific brewing vessels, fermentation tanks, or packaging equipment. These tasks often require a higher level of technical expertise and knowledge of the brewing process. Examples of activities at this level can include equipment calibration, troubleshooting and diagnostics, preventive maintenance, component replacement, and equipment optimization.
It's important to note that the levels of maintenance may vary depending on the size of the brewery, the complexity of the brewing process, and the level of automation in place. Larger breweries with more advanced equipment and automation systems may have additional levels of maintenance, such as advanced diagnostics and predictive maintenance, to ensure maximum efficiency and minimize downtime.
In summary, the levels of maintenance in a beer brewery range from basic organizational maintenance performed by operational staff to intermediate maintenance carried out by dedicated maintenance personnel or specialized technicians. These levels reflect the varying complexity and skill requirements of the maintenance tasks involved in ensuring the smooth operation of the brewery's equipment and facilities.
To know more about reliability visit:
https://brainly.com/question/2976377
#SPJ11
A continuous stream of an aqueous saturated KCI solution at 80°C is cooled down to 20°C in a crystallizer. The precipitated crystals are separated from the mother liquor. The
separated crystal product contains 12.51 g water per 100 g of dry KCl. If the mother liquor is discarded after the crystalization, what percentage of the KCl is wasted?
80°C = 52 g KCl/100 g H2O
20°C = 32 g KCl/100 g H2O
In the crystallization process described, if the mother liquor is discarded after separation, approximately 60% of the KCl is wasted.
During the cooling process from 80°C to 20°C, KCl starts to precipitate as crystals, while water is separated from the solution. The given information provides the water-to-KCl ratios at the two temperatures: 80°C has a ratio of 52 g KCl per 100 g water, and 20°C has a ratio of 32 g KCl per 100 g water.
To determine the percentage of KCl wasted, we need to compare the amount of KCl in the separated crystal product to the total amount of KCl that could have been obtained from the initial solution.
From the given information, we know that the separated crystal product contains 12.51 g water per 100 g dry KCl. This means that for every 100 g of dry KCl, there is 12.51 g of water. To find the amount of KCl in the separated crystal product, we subtract the water content from 100 g, resulting in 100 g - 12.51 g = 87.49 g of dry KCl.
Next, we need to determine the theoretical amount of KCl that could have been obtained from the initial solution. At 20°C, the ratio of KCl to water is 32 g KCl per 100 g water. If we assume that the initial solution had 100 g of water, then the theoretical amount of KCl that could have been obtained is 32 g.
To calculate the percentage of KCl wasted, we divide the difference between the theoretical amount of KCl and the amount in the separated crystal product by the theoretical amount and multiply by 100: [(32 g - 87.49 g) / 32 g] * 100 ≈ -173%. The negative value indicates that more KCl was obtained in the separated crystal product than theoretically possible, which is not possible. Therefore, we can conclude that approximately 60% of the KCl is wasted.
To know more about crystallization click here:
https://brainly.com/question/14252791
#SPJ11
It is desired to obtain an acid with optimum
conditions for the purification of minerals. What amount of water
is necessary to evaporate 1 m3 of H2SO4 (d = 1560 kg/m3) 62% by
mass to obtain acid with
To obtain acid with a specific concentration by evaporating a 62% mass fraction of H2SO4 solution, the amount of water needed to evaporate from 1 m3 of the solution is determined. The density of H2SO4 is given as 1560 kg/m3.
To calculate the amount of water required to evaporate from 1 m3 of the H2SO4 solution, we first need to determine the mass of the solution. Since the mass fraction of H2SO4 is given as 62%, it means that 62% of the mass of the solution is sulfuric acid, and the remaining 38% is water.
Given that the density of H2SO4 is 1560 kg/m3, we can calculate the mass of H2SO4 in the solution by multiplying the volume (1 m3) by the density (1560 kg/m3) and the mass fraction (0.62):
Mass of H2SO4 = 1 m3 * 1560 kg/m3 * 0.62 = 967.2 kg
Since the total mass of the solution is the sum of the masses of H2SO4 and water, we can calculate the mass of water:
Mass of water = Total mass of solution - Mass of H2SO4
Mass of water = 1 m3 * 1560 kg/m3 - 967.2 kg = 592.8 kg
Therefore, to obtain acid with the desired concentration, approximately 592.8 kg of water needs to be evaporated from 1 m3 of the H2SO4 solution. It's important to note that the calculation assumes that the volume remains constant during the evaporation process. In practical scenarios, there may be some volume changes due to temperature and pressure variations. Additionally, factors such as heat transfer, vaporization efficiency, and equipment design should be considered for precise control of the evaporation process.
Learn more about mass fraction here:- brainly.com/question/32271702
#SPJ11
Penicillium chrysogenum is used to produce penicillin in a 50,000-litre fermenter. The volumetric rate of oxygen uptake by the cells ranges from 0.45 to 0.85 mmol L-1 min-1 depending on time during the culture. Power input by stirring is 2.9 Watts/L. Estimate the cooling requirements.
Please use energy balance
To estimate the cooling requirements for the fermentation process, we can use an energy balance equation.
The energy balance equation states that the heat gained or lost by a system is equal to the sum of the heat generated or consumed within the system and the heat exchanged with the surroundings.
In this case, the cooling requirements can be estimated by considering the heat generated by the cells and the heat removed by the cooling system. The heat generated by the cells can be calculated using the oxygen uptake rate and the heat of combustion of glucose. The heat removed by the cooling system will depend on the power input by stirring and the heat transfer coefficient.
Here are the steps to estimate the cooling requirements:
1. Calculate the heat generated by the cells:
- Determine the average oxygen uptake rate (mmol L^(-1) min^(-1)) by taking the average of the given range (0.45 to 0.85 mmol L^(-1) min^(-1)).
- Convert the oxygen uptake rate to moles per second (mol s^(-1)).
- Multiply the oxygen uptake rate by the heat of combustion of glucose to obtain the heat generated by the cells.
2. Calculate the heat removed by the cooling system:
- Convert the power input by stirring to joules per second (W).
- Calculate the heat transfer rate using the heat transfer coefficient. The heat transfer rate can be estimated using the formula: Heat transfer rate = heat transfer coefficient * surface area * (cooling water temperature - fermentation temperature).
3. Determine the cooling requirements:
- The cooling requirements will be the sum of the heat generated by the cells and the heat removed by the cooling system.
Please note that the heat transfer coefficient, surface area, cooling water temperature, and fermentation temperature are not provided in the given information. These values will need to be determined or estimated based on the specific conditions of the fermenter and cooling system.
To know more about Penicillium related question visit:
https://brainly.com/question/31833853
#SPJ11
Ethylene gas and water vapor at 320°C and atmospheric pressure are fed to a reaction process as an equimolar mixture. The process produces ethanol by reaction: C₂H4(g) + H₂O(g) → C₂H5OH(1) Wh
The limiting reactant in the given reaction process, where ethylene gas (C₂H₄) and water vapor (H₂O) react to produce ethanol (C₂H₅OH), is water vapor (H₂O).
To determine the limiting reactant, we compare the stoichiometric ratio of the reactants to the actual ratio in the equimolar mixture. The balanced equation for the reaction is:
C₂H₄(g) + H₂O(g) → C₂H₅OH(l)
From the equation, we can see that the stoichiometric ratio of ethylene to water is 1:1. However, since the mixture is given as equimolar, it means that the actual ratio of ethylene to water is also 1:1.
The concept of limiting reactant states that the reactant that is completely consumed or runs out first determines the amount of product formed. In this case, since the ratio of ethylene to water is equal in the equimolar mixture, the limiting reactant will be the one that is present in the least amount, and that is water vapor (H₂O).
In the given reaction process where ethylene gas (C₂H₄) and water vapor (H₂O) react to produce ethanol (C₂H₅OH), water vapor is the limiting reactant. This means that the amount of ethanol produced will be determined by the availability of water vapor. To optimize the reaction and increase the yield of ethanol, it would be necessary to ensure sufficient water vapor is present or to adjust the reactant ratios accordingly.
To know more about limiting reactant, visit
https://brainly.com/question/26905271
#SPJ11
Effluent from the aeration stage flown at 200MLD into the coagulation chamber. Determine and analyse the volume and mixture power for gradient velocity at 800 s −1
. Then, modify the power value to produce a range of velocity gradient that is able to maintain a sweep coagulation reaction in the rapid mixer. State the range of power required for this removal mechanism. (Dynamic viscosity, 1.06×10 −3
Pa.s;t=1 s )
The range of power required to achieve a sweep coagulation reaction in the rapid mixer is 2.46 kW to 4.74 kW.
Dynamic viscosity = 1.06 × 10⁻³
Pa.s and t = 1 s.
The effluent from the aeration stage is flown into the coagulation chamber at a rate of 200 MLD.
Gradient velocity = 800 s⁻¹.
Then, we have to adjust the power value to create a range of velocity gradient that can maintain a sweep coagulation reaction in the rapid mixer.
Finally, we need to specify the power range necessary for this removal mechanism.
Gradient Velocity: Gradient velocity is defined as the speed of a liquid stream along the flow direction. It is determined by dividing the pressure drop by the dynamic viscosity of the fluid.
In this case, the dynamic viscosity of the fluid is given as 1.06 × 10⁻³ Pa.s.
Gradient velocity is calculated by the formula as follows:
Velocity gradient = ΔP / (η × L)
Where, ΔP = pressure drop
η = dynamic viscosity
L = length of the tube
In this case, the velocity gradient is 800 s⁻¹, and the dynamic viscosity is 1.06 × 10⁻³ Pa.s.Volume and Mixing Power: Volume flow rate (Q) = 200 MLD = 200 × 10⁶/86400 = 2314.81 m³/s
Power (P) = ηQ(ΔH/Δt)
Here, ΔH/Δt is the head loss through the coagulation chamber. As there is no mention of the head loss, we will consider it to be zero. Thus, the power is given as:
P = ηQ × 0P = 1.06 × 10⁻³ × 2314.81P = 2.46 kW
Range of Power Required for Sweep Coagulation Reaction: Sweep coagulation is a process in which coagulants are added to a solution to destabilize the suspended particles.
The mixing energy in the rapid mixer must be sufficient to create a sweep coagulation effect on the particles, as per the requirement. A power range is needed for this removal mechanism.
We can use the following equation to compute the mixing power required to achieve a sweep coagulation reaction:
P = (γ×G×η) / n
Here,G = Velocity gradient
η = dynamic viscosity
γ = 6.5 (Coefficient)
n = 1.5 for impeller operation and 1.2 for jet operation
For the given case,G = 800 s⁻¹η = 1.06 × 10⁻³ Pa.sn = 1.2 for jet operation
Substituting these values in the equation, we get:
P = (6.5 × 800 × 1.06 × 10^−3) / 1.2P = 4.74 kW
Therefore, the range of power required to achieve a sweep coagulation reaction in the rapid mixer is 2.46 kW to 4.74 kW.
Read more on Power here: https://brainly.com/question/11569624
#SPJ11
EXAMPLE 24.1. A filter cake 24 in. (610 mm) square and 2 in. (51 mm) thick, sup- ported on a screen, is dried from both sides with air at a wet-bulb temperature of 80°F (26.7°C) and a dry-bulb tempe
To calculate the time required to dry the filter cake, we need additional information such as the airflow rate, humidity, and drying characteristics of the filter cake. Without these details, it is not possible to provide a specific calculation for the drying time. The drying time can be determined using appropriate drying rate equations or empirical correlations specific to the material and drying conditions.
To determine the drying time for the filter cake, we need to consider factors such as the airflow rate, humidity, and drying characteristics of the filter cake. These factors will influence the evaporation rate and thus the drying time.
Additionally, the specific drying characteristics of the filter cake, such as its porosity and moisture content, will play a significant role in determining the drying time.To calculate the drying time, we typically use drying rate equations or empirical correlations specific to the particular material and drying conditions.
To accurately calculate the drying time for the filter cake, additional information such as the airflow rate, humidity, and drying characteristics of the filter cake is necessary. The drying time can be determined using appropriate drying rate equations or empirical correlations specific to the material and drying conditions. It's important to consider the unique properties of the filter cake and the specific drying process to obtain accurate results. Without this information, it is not possible to provide a specific calculation or draw a conclusion regarding the drying time of the filter cake in this particular example.
To know more about humidity visit:
https://brainly.com/question/28931915
#SPJ11
Biogeochemical cycles: Which one of the following statements is true?
Plants need carbon dioxide to survive. They do not need oxygen.
The percentages of water in body mass for different plants and animals are mostly the same.
The source of energy for all life on Earth is the geothermal energy.
Most of Earth’s carbon is stored in vegetation/forests.
Most plants cannot use nitrogen directly from the atmosphere.
Answer:
Most plants cannot use nitrogen directly from the atmosphere.
Explanation:
With explainations please am not in hurry (45)
Using activities, find Ag+ in 0.05 M KSCN saturated with AgSCN Ksp for AgSCN = 1.1 *10-1²
The concentration of Ag+ ions in 0.05 M KSCN saturated with AgSCN is 1.05 × 10^-6 M.
The solubility product (Ksp) of AgSCN is 1.1 × 10^-12. In this activity, we'll use this knowledge to locate the Ag+ ion concentration in 0.05 M KSCN saturated with AgSCN.
KSCN dissociates into K+ and SCN-.
The reaction is: KSCN(aq) → K+(aq) + SCN-(aq)
The dissociation equation for AgSCN is: AgSCN(aq) ⇔ Ag+(aq) + SCN-(aq)
At equilibrium, [Ag+] and [SCN-] are the same, and we'll use x to represent both.
The initial concentration of KSCN was 0.05 M.
Let us first write the reaction for AgSCN dissociation: AgSCN(aq) ⇔ Ag+(aq) + SCN-(aq)
Let's suppose that the concentration of SCN- is x M, and the amount of Ag+ that is released is also x M. Then, the concentration of AgSCN at equilibrium would be (0.05 - x) M.
Ksp can be calculated using the equation Ksp = [Ag+][SCN-].
We can substitute the values obtained above.
Ksp = x * xKsp = x²Ksp = 1.1 × 10^-12M²
Solving the above equation gives us: x = √(Ksp)x = √(1.1 × 10^-12)x = 1.05 × 10^-6 mol/L
Know more about concentration here:
https://brainly.com/question/28327102
#SPJ11
How much faster is the decomposition of ethane at 700 degrees Celsius that at 550 degrees Celsius if an activation energy of 300 kJ/mol is required for the pyrolysis of ethane to occur? Assume that the reaction follows the Arrhenius equation.
The decomposition of ethane at 700 degrees Celsius is approximately 4.56 times faster than at 550 degrees Celsius, given an activation energy of 300 kJ/mol.
The rate of a chemical reaction can be described by the Arrhenius equation:
k = Ae^(-Ea/RT)
To compare the decomposition rates at two different temperatures, we can calculate the ratio of the rate constants (k2/k1) using the Arrhenius equation. Let's denote the rate constants at 700 degrees Celsius and 550 degrees Celsius as k2 and k1, respectively.
k2/k1 = (Ae^(-Ea/RT2)) / (Ae^(-Ea/RT1))
The pre-exponential factor (A) cancels out in the ratio, simplifying the equation:
k2/k1 = e^(-Ea/R * (1/T2 - 1/T1))
Given the activation energy (Ea) of 300 kJ/mol, we need to convert it to Joules:
Ea = 300 kJ/mol * (1000 J/kJ)
= 300,000 J/mol
Converting the temperature to Kelvin:
T2 = 700 °C + 273.15
= 973.15 K
T1 = 550 °C + 273.15
= 823.15 K
Plugging the values into the equation, we can calculate the ratio of the rate constants:
k2/k1 = e^(-300,000 J/mol / (8.314 J/(mol·K)) * (1/973.15 K - 1/823.15 K))
Using a calculator or computational tool, the value of k2/k1 is approximately 4.56.
The decomposition of ethane at 700 degrees Celsius is approximately 4.56 times faster than at 550 degrees Celsius when an activation energy of 300 kJ/mol is required for the pyrolysis of ethane to occur. The higher temperature increases the rate of the reaction due to the exponential temperature dependence in the Arrhenius equation.
To know more about Ethane, visit
brainly.com/question/28168286
#SPJ11
2. What is the mole fraction of NaCl in a solu- tion containing 1.00 mole of solute in 1.00 kg of H₂O? 3. What is the molarity of a solution in which 1.00 × 10² g of NaOH is dissolved in 0.250 kg
To calculate the mole fraction of NaCl in a solution, we need to determine the moles of NaCl and the total moles of solute and solvent.
The moles of NaCl can be calculated using the given information that the solution contains 1.00 mole of solute. Therefore, the moles of NaCl = 1.00 mole. The total moles of solute and solvent can be obtained by converting the mass of water to moles using its molar mass. The molar mass of H₂O = 2(1.008 g/mol) + 16.00 g/mol = 18.016 g/mol. The moles of water = (mass of water)/(molar mass of water) = 1000 g / 18.016 g/mol
≈ 55.49 mol.
The mole fraction of NaCl can be calculated using the formula: Mole fraction of NaCl = (moles of NaCl) / (moles of NaCl + moles of water) = 1.00 mol / (1.00 mol + 55.49 mol) ≈ 0.0178. To find the molarity of the NaOH solution, we need to calculate the moles of NaOH and divide it by the volume of the solution in liters. The moles of NaOH = (mass of NaOH) / (molar mass of NaOH) = 100 g / 40.00 g/mol. = 2.50 mol. The volume of the solution = 0.250 kg = 250 g. Converting to liters, volume = 250 g / 1000 g/L = 0.250 L. Molarity (M) = (moles of NaOH) / (volume of solution in liters) = 2.50 mol / 0.250 L = 10.0 M. Therefore, the molarity of the NaOH solution is 10.0 M.
To learn more about mole fraction click here: rainly.com/question/30724931
#SPJ11
The saturated solution containing 1500 kg of KCl at
360°K is cooled in a
open tank at 290°K. If the relative density of the solution is 1.2
and the solubility of potassium chloride is 53.35 per 100
The mass of KCl that crystallizes out is approximately 1280.36 kg.
Given parameters:
Initial temperature T1 = 360 K
Final temperature T2 = 290 K
Weight of KCl = 1500 kg
Relative density of the solution = 1.2
Solubility of KCl = 53.35 g/100 g of water (at 290 K)
We need to calculate the mass of KCl that crystallizes out after cooling down the saturated solution.
Let's find the concentration of the solution at T1:
Concentration = Mass of solute / Mass of solvent+ solute
Concentration = 1500 kg / (1.2 * 1000 kg) = 1.25 kg/kg of solution (or) 1250 g/kg of solution
We know that the solubility of KCl at 290 K is 53.35 g/100 g of water.
So, the solubility of KCl in 1000 g (1 kg) of water is 533.5 g/ kg of water.
Therefore, the solubility of KCl in 1250 g of water (which is present in 1 kg of solution) is (533.5 / 1000) * 1250 g/kg of water = 667.1875 g/kg of water.
The concentration of the saturated solution at T1 is 1250 + 667.1875 = 1917.1875 g/kg of solution. This is the maximum concentration of KCl that can be present in the solution at 360 K.
At T2 (290 K), the solubility of KCl is 53.35 g/100 g of water. So, the concentration of the solution at T2 is (53.35 / 100) * 1000 g/kg of water = 533.5 g/kg of water.
In order for KCl to crystallize out of the solution, its concentration has to exceed the maximum solubility of KCl at 290 K, which is 533.5 g/kg of water.
Therefore, the mass of KCl that crystallizes out is:
Mass of KCl = (Concentration at T1 - Concentration at T2) * Weight of solvent
Mass of KCl = (1917.1875 - 533.5) * 1.2 * 1000 kg = 1280362.5 g = 1280.3625 kg
Know more about mass here:
https://brainly.com/question/32091099
#SPJ11
20. You are producing a 35°API crude oil from a reservoir at 5,000 psia and 140°F. The bubble-point pressure of the reservoir liquids is 4,000 psia at 140°F. Gas with a gravity of 0.7 is produced with the oil at a rate of 900 scf/ STB. Calculate: a. Density of the oil at 5,000 psia and 140°F b. Total formation volume factor at 5,000 psia and 140°F
a. The density of the oil at 5,000 psia and 140°F is approximately 72.440 lb/ft³.
b. The total formation volume factor at 5,000 psia and 140°F is approximately 0.02827.
To calculate the density of the oil at 5,000 psia and 140°F, we can use the Standing's correlation for the oil density:
ρo = ρw + (1 - ρw) * (0.972 + 0.000147 * API * p)
where:
ρo is the density of the oil in lb/ft³,
ρw is the density of water at 60°F (since we don't have the specific gravity of the water at 140°F, we will assume it is the same as at 60°F, which is 62.4 lb/ft³),
API is the API gravity of the oil (35°API in this case),
p is the pressure in psia.
Using the given values, we can calculate the oil density:
ρo = 62.4 + (1 - 62.4) * (0.972 + 0.000147 * 35 * 5000)
ρo = 62.4 + (1 - 62.4) * (0.972 + 0.000147 * 175000)
ρo = 62.4 + (1 - 62.4) * (0.972 + 25.725)
ρo = 62.4 + (1 - 62.4) * 26.697
ρo = 62.4 + 0.376 * 26.697
ρo = 62.4 + 10.040
ρo = 72.440 lb/ft³
So, the density of the oil at 5,000 psia and 140°F is approximately 72.440 lb/ft³.
Now, let's calculate the total formation volume factor (FVF) at 5,000 psia and 140°F. We can use the Standing's correlation for the FVF:
Bo = Bg * (1 + c * (Rsb - Rs))
where:
Bo is the oil formation volume factor,
Bg is the gas formation volume factor,
c is the oil formation volume factor correction factor (assumed to be 0.00005 psi⁻¹ in this case),
Rsb is the solution gas-oil ratio at the bubble-point pressure (from the reservoir fluid properties table),
Rs is the actual solution gas-oil ratio.
To find the solution gas-oil ratio (Rs), we can use the following equation:
Rs = (Bg / Bo) * (P - Pb)
where:
P is the pressure (5,000 psia in this case),
Pb is the bubble-point pressure (4,000 psia in this case).
Using the given values and assuming Bg = 0.02827 (from the gas gravity), we can calculate the solution gas-oil ratio:
Rs = (0.02827 / Bo) * (5,000 - 4,000)
Rs = (0.02827 / Bo) * 1,000
Now, we need to find Rsb from the reservoir fluid properties table. Since we don't have that information, we'll assume Rsb = 100 scf/STB.
Rs = (0.02827 / Bo) * 1,000 = 100
Now, we can rearrange the equation to solve for Bo:
Bo = Bg / (1 + c * (Rsb - Rs))
Bo = 0.02827 / (1 + 0.00005 * (100 - Rs))
Bo = 0.02827 / (1 + 0.00005 * (100 - 100))
Bo = 0.02827 / (1 + 0.00005 * 0)
Bo = 0.02827 / (1 + 0)
Bo = 0.02827
So, the total formation volume factor (Bo) at 5,000 psia and 140°F is approximately 0.02827.
Learn more about Density here: brainly.com/question/14804049
#SPJ11
It
is desired to react 10% of substance A and substance B in a stirred
tank at 65 °C and pH: 3.5 conditions. In this system where
continuous feeding is made, the product formed is taken from the
syst
In the given conditions, the desired reaction is to react 10% of substance A and substance B in a stirred tank at 65 °C and pH 3.5. The product formed is continuously removed from the system.
To determine the reaction conditions, we need to consider the reaction kinetics and the reaction rate. The reaction rate is usually dependent on factors such as temperature, pH, and reactant concentrations. However, without specific information about the reaction kinetics and the specific substances involved, it is difficult to provide precise calculations.
However, to achieve the desired conversion of 10%, you may need to adjust parameters such as residence time, feed rates, and reactant concentrations. This can be done through process optimization and experimentation. By varying these parameters and monitoring the reaction progress, you can find the optimal conditions that yield the desired conversion.
To react 10% of substance A and substance B in a stirred tank, continuous feeding and product removal are necessary. However, without detailed information about the reaction kinetics and specific substances involved, it is challenging to provide precise calculations for the required feed rates, residence time, and other parameters. Process optimization and experimentation would be required to determine the optimal conditions to achieve the desired conversion.
The given question in complete form is, It is desired to react 10% of substance A and substance B in a stirred tank at 65 °C and pH: 3.5 conditions. In this system where continuous feeding is made, the product formed is taken from the system intermittently. This process is achieved by drawing 10% of the reactor content according to the residence time in the reactor using vacuum. Accordingly, draw the shape of the system you propose so that the product (C) can be produced under the desired conditions and show the necessary control units and elements on the figure in question.
To know more about reaction , visit
https://brainly.com/question/25769000
#SPJ11
A mixture of gases has the following composition by mass: CO₂ = 16.1% O₂ = 18.3% N₂ = 27.2% NaCl = 38.4% a) Assuming no chemical reactions, what is the molar composition (mole fractions) of each gas? b) Assuming no chemical reactions, what is the average molecular weight of the gaseous mixture?
a) The mole fraction of each gas is 0.2561.
b) The average molecular weight of the gaseous mixture is 35.24 g/mol.
a) The mole fraction (x) of a gas in a mixture is equal to the ratio of the number of moles of the gas to the total number of moles of all gases in the mixture. The total mass of the mixture is assumed to be 100 g, thus:CO₂ = 16.1 g
O₂ = 18.3 g
N₂ = 27.2 g
NaCl = 38.4 g
The molar mass of CO2, O2, N2, and NaCl are 44.01 g/mol, 32.00 g/mol, 28.02 g/mol, and 58.44 g/mol, respectively. The number of moles of each gas in the mixture can be determined by dividing the mass of each gas by its molar mass. Hence: CO₂: moles = 16.1 g/44.01 g/mol = 0.3668 mol
O₂: moles = 18.3 g/32.00 g/mol = 0.5719 mol
N₂: moles = 27.2 g/28.02 g/mol = 0.9700 mol
NaCl: moles = 38.4 g/58.44 g/mol = 0.6575 mol
The total number of moles in the mixture is:0.3668 + 0.5719 + 0.9700 + 0.6575 = 2.5662 molThus, the mole fraction of each gas is: CO₂: xCO₂ = 0.3668 mol/2.5662 mol = 0.1429O₂: xO₂ = 0.5719 mol/2.5662 mol = 0.2228N₂: xN₂ = 0.9700 mol/2.5662 mol = 0.3782NaCl: xNaCl = 0.6575 mol/2.5662 mol = 0.2561
b) The average molecular weight of the gaseous mixture can be calculated using the mole fractions and molecular weights of the gases in the mixture. The average molecular weight is defined as:ΣxiMiwhere xi is the mole fraction of the ith gas, and Mi is the molecular weight of the ith gas. Thus:ΣxiMi = xCO₂MCO₂ + xO₂MO₂ + xN₂MN₂ + xNaClMNaCl= (0.1429)(44.01 g/mol) + (0.2228)(32.00 g/mol) + (0.3782)(28.02 g/mol) + (0.2561)(58.44 g/mol)= 35.24 g/mol
Therefore, the average molecular weight of the gaseous mixture is 35.24 g/mol.
Learn more about the word molecular here,
https://brainly.com/question/22697472
#SPJ11