The frequency of the sinusoid signal is 1000 Hz and the sampling rate is 20000 Hz. We can determine the zero crossing value by using the formula for finding the zero crossing of a sine wave signal when the sampling rate and frequency are known.
We will use the formula that gives us the zero crossing value. Formula : Zero Crossing Value = (Sampling Rate * Time period) / 2 We can calculate the time period from the frequency of the sine wave. Time period = 1 / Frequency Now, substitute the given values in the above formula to find the zero-crossing value. Zero Crossing Value = (20000 * 1/1000) / 2 = 100
Given the sinusoid signal frequency of 1000 Hz and the sampling rate of 20000 Hz, the zero crossing value can be calculated using the formula: Zero Crossing Value = (Sampling Rate * Time period) / 2, where Time period = 1 / Frequency. Thus, substituting the values in the above formula we get: Zero Crossing Value = (20000 * 1/1000) / 2 = 100. Therefore, the zero crossing value for 100 is 100.
The zero crossing value is a significant value in signal processing because it is used to calculate the frequency of a sinusoidal signal. The sampling rate and the frequency of the signal are critical factors in determining the zero crossing value. We can conclude that the zero-crossing value for a signal with a frequency of 1000 Hz and a sampling rate of 20000 Hz is 100.
To know more about sinusoid signal visit:
https://brainly.com/question/29455629
#SPJ11
If the stack height in the refinery is increased, the effect is:
a. To nail "lookey-loo" EPA spies using low flying aircraft/drones over the
plant.
b. To minimize the pollutants coming out the stack because they cannot
go so far up.
c. To minimize the hazards to personnel because the pollutants get dispersed before reaching the ground.
d. Create a positive draft for hot gases to rise up the stack.
e. To make the refinery look tall, dark and handsome.
Increasing the stack height in a refinery helps disperse pollutants, minimizing hazards to personnel and the environment by reducing pollutant concentration at ground level.
If the stack height in the refinery is increased, the effect is primarily to minimize the hazards to personnel and the surrounding environment. Option c is the most accurate choice. By increasing the stack height, the pollutants emitted from the stack are dispersed over a larger area and have more time to mix with the surrounding air, reducing the concentration of pollutants at ground level.
This helps to minimize the potential health risks to personnel and nearby communities. It does not necessarily impact the visibility of EPA spies or the aesthetics of the refinery (options a and e), and while it may create a positive draft for hot gases to rise (option d), the main objective is pollution dispersion and minimizing hazards.
Learn more about refinery here:
https://brainly.com/question/28540307
#SPJ11
Q3. Sketch the waveform of 32-QAM system for transmitting following bit streams 1111111111111100000000000000011111111111,10000000 1 2 3 4 5 6 7 8 9 10 11 12
Online resources, or simulation software that can provide you with visual representations of the 32-QAM constellation diagram and corresponding waveforms for specific bit streams.
32-QAM (Quadrature Amplitude Modulation) is a modulation scheme that combines both amplitude and phase modulation to transmit data. It uses 5 bits to represent each symbol, allowing for 32 different combinations.
The first bit stream you provided, "1111111111111100000000000000011111111111," is a sequence of high and low bits. In a 32-QAM system, these bits would be mapped to specific amplitude and phase levels. Each group of 5 bits represents one symbol, and each symbol corresponds to a specific point on the 32-QAM constellation diagram. The constellation diagram is a graphical representation of the different amplitude and phase levels used in the modulation scheme.
Similarly, the second bit stream, "10000000 1 2 3 4 5 6 7 8 9 10 11 12," would also be mapped to the corresponding amplitude and phase levels in the 32-QAM constellation diagram.
To visualize the waveform of a 32-QAM system, you would need to plot the amplitude and phase of each symbol over time. However, without specific amplitude and phase values for each symbol, it is not possible to provide an accurate waveform representation.
I recommend referring to textbooks, online resources, or simulation software that can provide you with visual representations of the 32-QAM constellation diagram and corresponding waveforms for specific bit streams.
Learn more about Online resources here
https://brainly.com/question/16717974
#SPJ11
Briefly describe TWO methods of controlling speed of a dc motor, and hence the operating principle of adjusting field resistance for speed control of a shunt motor. (4 marks) (b) Consider a 500 V, 1000 r.p.m. D.C. shunt motor with the armature resistance of 22 and field-circuit resistance of 250 32. The motor runs at no load and takes 3A when supplied from rated voltage. State all assumptions made, determine: (i) the speed when the motor is connected across a 250 V D.C. instead if the new flux is 60% of the original value; (ii) the back emf, field current, armature current and efficiency if the supply current is 20A; and (iii) the results of (b)(ii) if it runs as a generator supplying 20A to the load at rated voltage.
Armature voltage control adjusts applied voltage to vary speed, while field flux control modifies field resistance to control speed in a DC shunt motor.
Motor parameters:
- Armature voltage (V): 500 V
- Motor speed (N): 1000 rpm
- Armature resistance (Ra): 22 Ω
- Field-circuit resistance (Rf): 250ohm
Assumptions:
- Constant field flux
- Negligible armature reaction
- Linear relationship between field current and field resistance
1. Armature voltage control:
When using armature voltage control, we can adjust the applied voltage to the motor's armature to control the speed.
Calculations:
a. Back EMF (Eb):
The back EMF is given by the formula: Eb = V - Ia * Ra, where Ia is the armature current.
Since the armature voltage control method assumes constant field flux, the back EMF remains constant. Thus, the back EMF can be calculated by substituting the given values: Eb = 500 - Ia * 22.
b. Speed (N):
The speed of the motor is related to the back EMF and can be calculated using the formula: N = (V - Eb) / k, where k is a constant related to the motor's characteristics.
In this case, we can rearrange the formula as: N = (V - (V - Ia * 22)) / k = (Ia * 22) / k.
Given that N = 1000 rpm, we can solve for Ia: Ia = (N * k) / 22.
c. Field current (If):
Since we assumed a linear relationship between field current and field resistance, we can use Ohm's Law to calculate the field current.
Ohm's Law states: If = (V - Eb) / Rf.
Substituting the values, If = (500 - (500 - Ia * 22)) / 250.
d. Efficiency:
The efficiency (η) of the motor can be calculated using the formula: η = (Pout / Pin) * 100%, where Pout is the output power and Pin is the input power.
The output power can be calculated as: Pout = Eb * Ia.
The input power is given by: Pin = V * Ia.
Substituting the values and rearranging the formula, η = (Eb * Ia) / (V * Ia) * 100%.
2. Field flux control:
When using field flux control, we adjust the field resistance to control the field current and, consequently, the motor's speed.
Calculations:
a. Field current (If):
Using Ohm's Law, we can calculate the field current as: If = (V - Eb) / Rf.
Since we assumed a linear relationship between field current and field resistance, we can rearrange the formula as: If = (V - Eb) / Rf = (V - (V - Ia * 22)) / Rf.
Substituting the values, If = (500 - (500 - Ia * 22)) / 250.
b. Speed (N):
The speed of the motor is related to the field current and can be calculated using the formula: N = k * If.
Given that N = 1000 rpm, we can solve for If: If = N / k.
c. Back EMF (Eb):
Since we assumed constant field flux, the back EMF remains constant. Thus, the back EMF can be calculated by substituting the given values: Eb = 500 - Ia * 22.
d. Armature current (Ia):
The armature current can be calculated using Oh
Learn more about armature voltage here
https://brainly.com/question/31980690
#SPJ11
Solve for I, then convert it to time-domain, in the circuit below. 0.2 (2 —j0.4 1 Ht 32/-55° V 21 0.25 N +i j0.25 02
Given circuit: 0.2 (2 —j0.4 1 Ht 32/-55° V 21 0.25 N +i j0.25 02In order to solve for I and convert it to the time-domain, we can use the phasor analysis method. Let's begin:Firstly, we need to assign a phasor voltage to each voltage source. Here, we have two voltage sources: 32/-55° V and 21 V.
The first voltage source can be represented as 32 ∠ -55° V and the second voltage source can be represented as 21 ∠ 0° V. The phasor diagram for the given circuit is shown below: [tex]\implies[/tex] I = V / ZT, where V is the phasor voltage and ZT is the total impedance of the circuit. ZT can be calculated as follows:
ZT = Z1 + Z2 + Z3We are given the following values:Z1 = 2 - j0.4 ΩZ2 = j0.25 ΩZ3 = 0.25 ΩImpedance Z1 has a resistance of 2 Ω and a reactance of -0.4 Ω, impedance Z2 has a reactance of 0.25 Ω, and impedance Z3 has a resistance of 0.25 Ω. Therefore, the total impedance of the circuit is:ZT = Z1 + Z2 + Z3= 2 - j0.4 + j0.25 + 0.25= 2 + j0.1 ΩI = V / ZT = (32 ∠ -55° + 21 ∠ 0°) / (2 + j0.1) Ω= 18.48 ∠ -38.81° A. Now, to convert it to time-domain we use the inverse phasor transformation:
The phasor analysis method is used to solve for I and convert it to the time-domain. In this method, a phasor voltage is assigned to each voltage source. Then, the total impedance of the circuit is calculated by adding up the individual impedances of the circuit. Finally, the current is calculated as the ratio of the phasor voltage to the total impedance. The phasor current obtained is then converted to the time-domain by using the inverse phasor transformation.
In conclusion, we solved for I and converted it to the time-domain in the given circuit. The phasor analysis method was used to obtain the phasor current and the inverse phasor transformation was used to convert it to the time-domain. The final answer for I in the time-domain is 0.15cos(500t - 38.81°) A.
To know more about impedance visit:
https://brainly.com/question/30475674
#SPJ11
List the THREE (3) particles that make up an atom and draw the atomic structure. (4 marks) Define the following terms: i. Hole current ii. Intrinsic semiconductor iii. lonization (6 marks) Describe the mechanism of electron conduction iniside the semiconductor which includes the excitation/energy sources of the electrons. (6 marks) Compare the TWO (2) material which is known as donor or acceptor. How this two impurities different from each other? (4 marks)
1. The three particles that make up an atom are:
a. Protons: Positively charged particles found in the nucleus of an atom.
b. Neutrons: Neutral particles found in the nucleus of an atom.
c. Electrons: Negatively charged particles orbiting around the nucleus.
i. Hole current: In a semiconductor, when an electron from the valence band moves to the conduction band, it leaves behind a vacancy known as a hole. The movement of these holes is referred to as hole current. Holes behave like positive charges and can contribute to current flow in a semiconductor.
ii. Intrinsic semiconductor: An intrinsic semiconductor is a pure semiconductor material with no intentional impurities. It has equal numbers of electrons in the conduction band and holes in the valence band at thermal equilibrium. Examples of intrinsic semiconductors include pure silicon (Si) and germanium (Ge).
iii. Ionization: Ionization refers to the process of removing or adding electrons to an atom, resulting in the formation of ions. It can occur due to various mechanisms such as thermal excitation, collisions, or exposure to electromagnetic radiation. Ionization can lead to the generation of free charge carriers (electrons and holes) in a semiconductor.
Description of electron conduction mechanism inside a semiconductor:
When a semiconductor is subjected to an energy source (e.g., heat, light, or electric field), the electrons in the valence band gain enough energy to move to the higher energy conduction band. This excitation of electrons creates electron-hole pairs. The energy source can provide the required energy through various processes, such as thermal excitation, absorption of photons, or electric field-induced drift.
In thermal excitation, the energy source is heat, which increases the temperature of the semiconductor and causes electrons to gain energy. In the case of photon absorption, photons with energy higher than the bandgap of the semiconductor can be absorbed by electrons, raising them to the conduction band. Electric field-induced drift occurs when an external electric field is applied to the semiconductor, causing the electrons to move towards the positive terminal.
Comparison between donor and acceptor impurities:
Donor impurity: A donor impurity is an impurity atom that introduces additional electrons to the semiconductor's conduction band. Donor impurities have more valence electrons than the host semiconductor, such as phosphorus (P) in silicon.
Acceptor impurity: An acceptor impurity is an impurity atom that creates additional holes in the semiconductor's valence band by accepting electrons from the host material. Acceptor impurities have fewer valence electrons than the host semiconductor, such as boron (B) in silicon.
Difference between donor and acceptor impurities:
- Donor impurities introduce extra electrons, while acceptor impurities create additional holes.
- Donor impurities have more valence electrons than the host semiconductor, while acceptor impurities have fewer valence electrons.
- Donor impurities contribute to n-type doping, while acceptor impurities contribute to p-type doping in semiconductors.
The three particles that make up an atom are protons, neutrons, and electrons. Intrinsic semiconductors are pure semiconductor materials with no intentional impurities. Ionization refers to the process of removing or adding electrons to an atom. The mechanism of electron conduction in a semiconductor involves excitation of electrons by thermal energy, photon absorption, or electric field-induced drift. Donor impurities introduce extra electrons, while acceptor impurities create additional holes. Donor impurities have more valence electrons, while acceptor impurities have fewer valence electrons compared to the host semiconductor.
To know more about atom , visit
https://brainly.com/question/15053224
#SPJ11
Write and execute a JAVA program that will allow the user to input the prices of 7 items into an array using for loop. The program should determine the maximum price using while loop and then display the same. Sample output: Enter price:12 Enter price:34 Enter price:11 Enter price:2 Enter price:34 Enter price:56 Enter price: 78 maximum price: 78.0 Press any key to continue...
Here's a Java program that allows the user to input the prices of 7 items into an array using a for loop, determines the maximum price using a while loop, and then displays the same.
Sample output is also provided:
```java import java.util.
Scanner;
public class Main { public static void main(String[] args) { Scanner input = new Scanner(System.in); double[] prices = new double[7]; for (int i = 0; i < prices.
length; i++) { System.
out. print("Enter price: "); prices[i] = input.
nextDouble(); } double maxPrice = prices[0]; int i = 1; while (i < prices.length) { if (prices[i] > maxPrice) { maxPrice = prices[i]; } i++; } System.
out.println("maximum price: " + maxPrice); System.
out.println ("Press any key to continue..."); input.nextLine(); input.close(); }}```
A Java program can be described as a collection of objects that invoke each other's methods to communicate. Let's take a quick look at the meanings of instance variables, methods, classes, and objects. Object. There are states and behaviors in objects.
Know more about Java program:
https://brainly.com/question/2266606
#SPJ11
14. Consider the accompanying code. What is the effect of the following statement? newNode->info = 50; a. Stores 50 in the info field of the newNode b. Creates a new node c. Places the node at location 50 d. Cannot be determined from this code 15. Consider the accompanying statements. The operation returns true if the list is empty; otherwise, it returns false. The missing code is a. protected b. int c. void d. bool
Question 14 The effect of the statement `newNode->info = 50;` is that it stores 50 in the `info` field of the `newNode`.
.Question 15 The missing code that would complete the given statements is `bool`.
A linked list is a data structure that is a collection of items that are connected to each other through links. These links point to the next item or the previous item. A linked list is made up of nodes that have data fields and pointers to the next or previous item.
The given statements describe the operation that returns `true` if the list is empty, otherwise, it returns `false`.Therefore, the missing code that would complete the given statements is `bool` since the return type of the operation is a Boolean value.
Learn more about the linked list:
https://brainly.com/question/14527984
#SPJ11
Tell how many roots of the following polynomial are in the right half-plane, in the left half-plane, and on the jo-axis: [Section: 6.2] P(s) = 55 +354 +5³ +4s² + s +3
The polynomial is P(s) = 55 +354 +5³ +4s² + s +3. The following are the number of roots of the polynomial P(s) in the right half-plane, left half-plane, and on the jo-axis.How many roots of the following polynomial are in the right half-plane, in the left half-plane, and on the jo-axis:
[Section: 6.2] P(s) = 55 +354 +5³ +4s² + s +3: There are no roots of the polynomial P(s) in the right half-plane.There are no roots of the polynomial P(s) in the left half-plane.The polynomial has no roots on the jo-axis since the constant term, P(0) = 55 +354 +5³ +3 is a positive value while all other coefficients are positive.In summary, there are no roots of the polynomial P(s) in the right half-plane, left half-plane, and on the jo-axis.
To know more about polynomial visit:
https://brainly.com/question/11536910
#SPJ11
A process has an input-output transfer function estimated to be: i) ii) The process is under closed loop, unity feedback control with a proportional controller, Kc. -Os G₁(s) = Determine the closed loop characteristic equation for the system. e -2s What range of values can be used for Ke for the closed loop system to be stable? Use a first order Pade approximation to represent the dead-time, 1-(0/2)s 1+(0/2)s 2e 8s+ 1 2 and the Routh test.
Given the transfer function of a closed loop control system, G1(s) = Kc / ((s + 2) (s + 3) (s + 4)), we are required to determine the closed loop characteristic equation for the system.
To find the closed-loop transfer function, we can write G2(s) = G1(s) / (1 + G1(s)). This can be simplified to G2(s) = Kc / ((s + 2) (s + 3) (s + 4) + Kc).
In order for the system to be stable, we need to find the range of Kc for which all roots of the characteristic equation lie in the left half of the s-plane.
The closed loop characteristic equation can be found by equating 1 + Kc / ((s + 2) (s + 3) (s + 4) + Kc) to 0. On solving, we get s³ + (9 + 2Kc) s² + (26 + 3Kc) s + 24 + 4Kc = 0.
Using the first-order Pade approximation of time delay, we can represent 1 - (0.5s / 1 + 0.5s) as (s - 1) / (s + 2). By adding this time delay model to the closed-loop transfer function, we can obtain a new transfer function G3(s) = Kc (s - 1) / [(s + 2) (s + 3) (s + 4) + Kc (s - 1)].
The closed loop characteristic equation of the new system can be obtained by equating 1 + Kc (s - 1) / [(s + 2) (s + 3) (s + 4) + Kc (s - 1)] to 0. On solving, we get s³ + (Kc + 9) s² + (-Kc - 3) s + (4Kc + 24) = 0.
The stability of a system is essential for it to operate effectively. The coefficients of the polynomial of the closed loop characteristic equation should be positive for the system to be stable. To determine the range of Kc values for which the coefficients of the polynomial are positive, we can use the Routh-Hurwitz stability criterion.
The Routh-Hurwitz stability criterion is shown below:
S³ 1 Kc + 9 -Kc - 3
S² Kc + 7 Kc + 21
S¹ -3Kc - 21 4Kc + 24
Sº 4Kc + 24
If all the coefficients of the polynomial are positive, the system is stable. In this case, the range of Kc values for stability is given by 0 < Kc < 3. Therefore, the closed loop characteristic equation for the system is s³ + (Kc + 9) s² + (-Kc - 3) s + (4Kc + 24) = 0.
The range of values that can be used for Ke for the closed loop system to be stable is 0 < Kc < 3. The stability of the system is crucial in ensuring that it functions optimally.
Know more about Routh-Hurwitz stability criterion here:
https://brainly.com/question/31479909
#SPJ11
A filter with the following impulse response: دلا wi h(n) wi sin(nw) nw21 w2 sin(nw2) nw2 with h(0) con, (wi
The given filter has the following impulse response,wi sin(nw1)[tex]+ nw1 * w2 sin(nw2) + nw2 * w2 sin(nw2).[/tex]wi is the angular frequency and w1 and w2 are the two distinct angular frequencies with w1 < w2.
h(0) = cos(wi). The filter has a linear phase.the filter's output is given by:y(n) = ∑k= -∞to ∞ x(k) h(n - k)The discrete-time Fourier transform of the filter's impulse response is given by:H(ejw) = cos(wi) + j [wi sin(w1) + ejw1 w1 sin(w1) + ejw2 w2 sin(w2) + ejw1 (w1 + w2) sin(w2)]Thus, the magnitude response of the filter is given by |H(ejw)| and its phase response is given by arg(H(ejw)).
The filter has two zeroes and two poles located on the unit circle of the z-plane. Both the zeroes lie at z = ejw2 and both the poles lie at z = ejw1.The filter's frequency response is characterized by a bandpass with a central frequency equal to w2 and a band width equal to w2 - w1.
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
Name minimum 5 tests shall be held on site for a LV switchboard? Question 3 (5 marks
When conducting on-site testing for LV switchboards, there are several tests that must be performed to ensure their proper functioning. Here are at least five such tests that must be performed on-site.
Insulation Resistance Test (IR)The insulation resistance test (IR) is performed to verify the insulation resistance value of the switchgear. The IR test is carried out at a voltage of 500V DC (or 1000V DC for a 1KV switchboard) with a minimum insulation resistance value of 1 Mega ohm (MOhm) for switchboards.
Visual InspectionAll switchboard parts should be visually inspected to ensure that they are properly installed, secured, and connected. All labeling should be checked to ensure that it is correct and visible.3. Mechanical Operation TestThis test is conducted to verify the correct functioning of the mechanical aspects of the switchboard.
To know more about armature visit:
https://brainly.com/question/31364875
#SPJ11
Consider a modulated signal defined as X(t) = Ac coswcet - Am cos (wc-wm)t + Ancos (WC+Wm) t which of the following should be used to recover the message sign from this sign? A-) Square law detector only 3-) None (-) Envelope detector only 1-) Envelope detector or square law detector question The g(t)= x (t) sin(woont) sign is obtained by modulating x(t) = sin(2007t) + 2 sm (Goont) the The sign. g(t) Signal is then passed through a low pass filter with a cutoff frequency of Goor Hz and a passband gain of 2. what is the signal to be obtained at the filter output? A-) 0,5 sn (200nt) B-) Sin (200nt) (-)0 D-) 2 sin (2001) question frequency modulation is performed using the m(t)=5c0s (2111oot) message signal. Since the obtained modulated signal is s(t) = 10 cos((2110³) +15sm (201004)), approximately what is the bandwidth of the FM signal? A- 0.2 KHZ B-) 1KHZ (-) 3.2KHZ D-) 100 KHZ
The recovery of a message signal from the modulated signal X(t) necessitates the use of an envelope detector or a square law detector.
The signal g(t) will yield 0.5 sin (200πt) when passed through a low-pass filter. The bandwidth of the frequency-modulated signal is approximately 3.2 KHz. In the given modulated signal X(t), both the envelope detector and the square law detector could be used to recover the message signal. The signal g(t) has been modulated and will give 0.5 sin (200πt) after passing through a low-pass filter with a cutoff frequency of 100 Hz. The low-pass filter removes the high-frequency component from the signal, leaving the desired signal of 0.5 sin (200πt). When frequency modulation is done using m(t)=5 cos (2π100t), the resulting modulated signal is s(t) = 10 cos((2π10³t) +15 sin (2π100t)). The bandwidth of this FM signal is approximately 3.2 KHz, calculated based on Carson's rule.
Learn more about signal modulation here:
https://brainly.com/question/31733518
#SPJ11
3. Suppose that the Stack class uses Single_list and we want to move the contents of one stack onto another stack. Because the Stack is not a friend of the Single_list (and it would be foolish to allow this), we need a new push_front( Single_list & ) function that moves the contents of the argument onto the front of the current linked list in (1) time while emptying the argument.
4. Consider the undo and redo operations or forward and back operations on a browser. While it is likely more obvious that operations to undo or pages to go back to may be stored using a stack. what is the behaviour of the redo or page forward operations? How is it related to being a stack? Are there times at which the redo or forward operations stored in the stack are cleared.
To move the contents of one stack onto another stack, a new push_front(Single_list&) function is needed in the Stack class.
This function should move the contents of the argument onto the front of the current linked list in constant time while emptying the argument.
In the context of undo and redo operations or page forward and back operations in a browser, the behavior of the redo or page forward operations is related to being a stack.
Redo operations allow the user to move forward in the sequence of actions or pages visited, similar to popping elements from a stack. There may be times when the redo or forward operations stored in the stack are cleared, typically when a new action or page is visited after performing an undo operation.
To move the contents of one stack onto another stack, the push_front(Single_list&) function can be implemented as follows:
void Stack::push_front(Single_list& other_list) {
if (other_list.empty()) {
return; // If the other_list is empty, there is nothing to move
}
// Move the nodes from other_list to the front of the current linked list
Node* other_head = other_list.head;
other_list.head = nullptr; // Empty the other_list
if (head == nullptr) {
head = other_head;
} else {
Node* temp = head;
while (temp->next != nullptr) {
temp = temp->next;
}
temp->next = other_head;
}
}
Regarding the behavior of redo or page forward operations, they are typically implemented using a stack data structure.
When an undo operation is performed, the previous action or page is popped from the stack and becomes eligible for redo or page forward. Redo operations allow the user to move forward in the sequence of actions or pages visited.
However, if a new action or page is visited after performing an undo operation, the redo stack may be cleared to maintain the correctness of the forward operations. This ensures that redoing a previously undone action does not conflict with subsequent actions performed after the undo.
To learn more about Stack class visit:
brainly.com/question/32882005
#SPJ11
Assume that there are the positive numbers in memory locations at the addresses from x3000 to x300F. Write a program in LC-3 assembly language with the subroutine to look for the minimum odd value, then display it to screen. Your program begins at x3010.
The program in LC-3 assembly language starts at memory address x3010 and aims to find the minimum odd value among the positive numbers stored in memory locations x3000 to x300F. Once the minimum odd value is determined, it is displayed on the screen.
To solve this problem, we can use a simple algorithm in the LC-3 assembly language. The program initializes a register to store the minimum odd value found so far, setting it to a large initial value. It then iterates through the memory locations from x3000 to x300F, examining each value. For each value, the program checks if it is both odd and smaller than the current minimum odd value. If both conditions are satisfied, the value becomes the new minimum odd value. Once all the memory locations have been checked, the program displays the minimum odd value on the screen.
By implementing this algorithm, the program effectively searches for the minimum odd value among the positive numbers stored in memory. It ensures that the minimum odd value is updated whenever a smaller odd value is encountered. The use of registers allows for efficient storage and comparison of values, while the conditional checks ensure that only odd values are considered for the minimum. Finally, displaying the minimum odd value provides a clear output to the user.
Learn more about display here:
https://brainly.com/question/32200101
#SPJ11
A coaxial cable of inner radius a and outer radius b consists of two long metallic hollow cylindrical pipes. Find the capacitance per unit length for the cable.
The capacitance per unit length for the given coaxial cable can be obtained as follows:$$C = \frac{{2\pi \varepsilon }}{{\ln \frac{b}{a}}} = \frac{{2\pi \left( {{\varepsilon _r}{\varepsilon _0}} \right)}}{{\ln \frac{b}{a}}}$$.
The capacitance per unit length for the coaxial cable can be calculated using the following equation:
$$C = \frac{{2\pi \varepsilon }}{{\ln \frac{b}{a}}}$$
Where; C is the capacitance per unit length of the cable.
ε is the permittivity of the medium between the two cylinders.
The permittivity can be determined by ε = εrε0, where εr is the relative permittivity of the medium and ε0 is the permittivity of free space. 2π is the constant used for circular perimeters. a and b are the inner and outer radii of the two cylinders, respectively. The natural logarithm function ln is used to determine the ratio of b to a which gives the capacitance per unit length.
To know more about capacitance refer to:
https://brainly.com/question/30902642
#SPJ11
At the end of the experiment, student should be able to: - 1) To study the relationship between voltage and current in three-phase circuits. 2) To learn how to make wye and wye connections. 3) To calculate the power in three-phase circuits. 2.0 EQUIPMENT: 1. AC power supply 2. Digital multi-meter (DMM) 3. Connecting cables 3.0 COMPONENTS: 1. Simulation using Multisim ONLINE Website 2. Generator: V = 120/0° V, 60Hz 3. Line impedance: R=102 and C=10 mF per phase, 4. Load impedance: R=30 2 and L=15 µH per phase, 5.0 PROCEDURES: 1. a) From the specification given in component listing, show the calculation on how to get the remaining phase voltage of the generator source and record the value below. The system using abc phase sequence. V = 120/0° V. rms = = cn rms b) Draw and construct the 3-phase AC system on the Multisim online software by using the specification in component listing and the information in procedure la). Copy and paste the circuit diagram below c) Measure the 3-phase voltage of generator source. Copy and phase these 3-phase waveform to see the relationship these three voltages to prove follow the abc sequence. d) Calculate the value of line to line voltage and record the result below. (Show the calculation) V₂b = ab mms Vbc = rms V₁ = rms e) Measure the 3-phase voltage of line-to-line voltage. Copy and paste the result of voltage measurement below. √ ba V V rms
The experiment aims to study voltage-current relationship in three-phase circuits, learn wye and delta connections, and calculate power using specified equipment and components.
(a) The experiment aims to investigate the relationship between voltage and current in three-phase circuits. It involves using an AC power supply, digital multi-meter (DMM), and connecting cables.
(b) The experiment also focuses on understanding wye and delta connections, which are common configurations in three-phase systems.
(c) Additionally, the experiment covers the calculation of power in three-phase circuits, considering line and load impedances.
The experiment provides students with hands-on experience and theoretical knowledge related to three-phase circuits. By studying the voltage-current relationship, practicing wye and delta connections, and performing power calculations, students gain a comprehensive understanding of three-phase systems. The practical use of simulation software and measurement tools enhances their skills in analyzing and designing three-phase circuits.
To know more about Three-phase circuit , visit:- brainly.com/question/31752076
#SPJ11
Transposition of transmission line is done to a. Reduce resistance b. Balance line voltage drop c. Reduce line loss d. Reduce corona e. Reduce skin effect f. Increase efficiency 4) Bundle conductors are used to reduce the effect of a. Resistance of the circuit b. Inductance of the circuit c. Inductance and capacitance d. Capacitance of the circuit e. Power loss due to corona f. All the mentioned
Transposition of transmission line is done to balance line voltage drop. Bundle conductors are used to reduce the effect of inductance and capacitance of the circuit.Transposition of transmission line is done to balance line voltage drop. This is one of the most important purposes of transposition of transmission line.
Transposition of transmission lines is also done to increase efficiency and reduce the corona effect. It is done to ensure that all the phases experience the same amount of voltage drop. If the phases experience different voltage drops, it will cause unbalanced voltages across the three-phase system. This will cause the transmission line to become inefficient.Bundle conductors are used to reduce the effect of inductance and capacitance of the circuit. The bundle conductor is a system of multiple conductors that are closely spaced together. This reduces the inductance and capacitance of the transmission line. When multiple conductors are used, they tend to cancel each other’s magnetic fields. This makes it easier to reduce the inductance and capacitance of the circuit.
Know more about Transposition here:
https://brainly.com/question/22856366
#SPJ11
Toggle state means output changes to opposite state by applying.. b) X 1 =..... c) CLK, T inputs in T flip flop are Asynchronous input............. (True/False) d) How many JK flip flop are needed to construct Mod-9 ripple counter..... in flon, Show all the inputs and outputs. The
For a Mod-9 ripple counter, we need ⌈log2 9⌉ = 4 flip-flops. The first column represents the clock input, and the rest of the columns represent the output Q of each flip-flop.
Toggle state means output changes to opposite state by applying A pulse with a width of one clock period is applied to the T input of a T flip-flop. The statement is given as false as the Asynchronous inputs for the T flip-flop are SET and RESET.
Explanation: As the question requires us to answer multiple parts, we will look at each one of them one by one.(b) X1 = 150:When X1 = 150, it represents a hexadecimal number. Converting this to binary, we have;15010 = 0001 0101 00002Therefore, X1 in binary is 0001 0101 0000.(c) CLK, T inputs in T flip flop are Asynchronous input (True/False)Asynchronous inputs in a T flip-flop are SET and RESET, not CLK and T. Therefore, the statement is false.(d) How many JK flip flop are needed to construct Mod-9 ripple counter in flon, Show all the inputs and outputs.The number of flip-flops required to construct a Mod-N ripple counter is given by the formula:No. of Flip-Flops = ⌈log2 N⌉.
Therefore, for a Mod-9 ripple counter, we need ⌈log2 9⌉ = 4 flip-flops. The following table represents the inputs and outputs of the counter.The first column represents the clock input, and the rest of the columns represent the output Q of each flip-flop.
Learn more on Asynchronous here:
brainly.com/question/31888381
#SPJ11
The AC currents of a star-connected 3-phase system a-b-c (as shown in Figure Q7) are measured. At a particular instant when the d-axis is making an angle θ = +40o with the a-winding.
ia 23 A ; ib 5.2 A ; ic 28.2 A
Use the Clarke-Park transformation to calculate id and iq. No constant to preserve conservation of power is to be added.
The calculated values for id and iq using the Clarke-Park transformation are approximately id = 16.939 A and iq = -5.394 A, respectively.
o calculate id and iq using the Clarke-Park transformation, we need to follow a series of steps. Let's go through them:
Step 1: Clarke transformation
The Clarke transformation is used to convert the three-phase currents (ia, ib, ic) in a star-connected system to a two-phase representation (ia0, ia1).
ia0 = ia
ia1 = (2/3) * (ib - (1/2) * ic)
In this case, we have:
ia = 23 A
ib = 5.2 A
ic = -28.2 A
Substituting the values into the Clarke transformation equations, we get:
ia0 = 23 A
ia1 = (2/3) * (5.2 A - (1/2) * (-28.2 A))
= (2/3) * (5.2 A + 14.1 A)
= (2/3) * 19.3 A
≈ 12.87 A
Step 2: Park transformation
The Park transformation is used to rotate the two-phase representation (ia0, ia1) to a rotating frame of reference aligned with the d-axis.
id = ia0 * cos(θ) + ia1 * sin(θ)
iq = -ia0 * sin(θ) + ia1 * cos(θ)
In this case, θ = +40°.
Substituting the values into the Park transformation equations, we get:
id = 23 A * cos(40°) + 12.87 A * sin(40°)
≈ 16.939 A
iq = -23 A * sin(40°) + 12.87 A * cos(40°)
≈ -5.394 A
Therefore, the calculated values for id and iq using the Clarke-Park transformation are approximately id = 16.939 A and iq = -5.394 A, respectively.
Learn more about transformation here
https://brainly.com/question/30784303
#SPJ11
Electrical Power Engineering Year End Examination 2019 QUESTION 4 [8] 4. A coil of inductance 0, 64 H and resistance 40 ohm is connected in series with a capacitor of capacitance 12 µF. Calculate the following: 4.1 The frequency at which resonance will occur (2) 4.2 The voltage across the coil and capacitor, respectively and the supply voltage when a current of 1.5 A at the resonant frequency is flowing. (3) 4.3 The voltage across the coil and capacitor, respectively and the supply voltage when a current of 1.5 A flowing at a frequency of 50 Hz
The frequency at which resonance will occur.Resonance will occur when the reactance of the inductor is equal and opposite to the reactance of the capacitor.
Thus, the resonance frequency is given by the formula :f = 1/(2π√LC) Where f is frequency, L is the inductance of the coil, and C is the capacitance of the capacitor. Substituting given values: L = 0.64 H and C = 12 µF We know that 1 µF = 10^-6 F and 1/(2π) ≈ 0.16, thus, f = 1/(2π√LC)= 1/(2π√(0.64)(12×10^-6))≈ 365.3 Hz.
Therefore, the frequency at which resonance will occur is 365.3 Hz.4.2. The voltage across the coil and capacitor, respectively and the supply voltage when a current of 1.5 A at the resonant frequency is flowing. The current in the circuit is given as 1.5 A at the resonant frequency of 365.3 Hz.
To know more about resonance visit:
https://brainly.com/question/28318319
#SPJ11
Design a simple matching network of your choice to match a 73 ohm load to a 50 ohm transmission line at 100 MHz. Assume that you can use lumped elements.
A simple matching network can be designed using lumped elements to match a 73-ohm load to a 50-ohm transmission line at 100 MHz.
To achieve this, a combination of an inductor and a capacitor can be used. The inductor acts as an impedance transformer, while the capacitor compensates for the reactive component of the load impedance. By properly selecting the values of the inductor and capacitor, the desired impedance transformation and matching can be achieved. Lumped element matching networks are designed using discrete components such as inductors and capacitors. In this case, we want to match a 73 ohm load to a 50 ohm transmission line at 100 MHz. To begin, we can use an inductor in series with the load to transform the impedance.
The inductor's value can be calculated using the formula: L = Z0 / (2πf). where L is the inductance, Z0 is the characteristic impedance of the transmission line (50 ohms in this case), f is the frequency (100 MHz in this case), and π is a constant. Next, we need to compensate for the reactive component of the load impedance. This can be done by placing a capacitor in parallel with the load. The value of the capacitor can be calculated using the formula: C = 1 / (2πfZ0). where C is the capacitance. By properly selecting the values of the inductor and capacitor, impedance transformation and matching can be achieved, ensuring minimal reflection and maximum power transfer between the load and the transmission line at 100 MHz.
Learn more about inductor here:
https://brainly.com/question/31503384
#SPJ11
Do not use the lumped model for this transient problem.
A metallic cylinder with initial temperature 350°C was placed into a large bath with temperature 50°C (convection coefficient estimated as 400 W/m2 K). A diameter and a height of the cylinder are equal to 100 mm. The thermal properties are:
conductivity 40 W/mK,
specific heat 460 J/kgK,
density 7800 kg/m3
Calculate maximum and minimum temperatures in the cylinder after 4 minutes.
This is a short cylinder.
The lumped model can be used for the analysis of transient conduction in solids. When convection and radiation are negligible, the lumped model can be applied.
The problem statement states that the lumped model should not be used for this transient problem because the length of the cylinder is not small compared to its characteristic length, meaning that heat transfer will occur in both the radial and axial directions. As a result, a more complex analysis method should be used.A metallic cylinder with a diameter of 100 mm and a height of 100 mm was placed in a large bath with a convection coefficient estimated at 400 W/m2K and a temperature of 50°C.
Since the length of the cylinder is comparable to its diameter, a finite difference method can be used to solve the equation of cylindrical heat conduction. Because of the complexity of the problem, the analytical solution is not a practical solution. The temperature distribution can be calculated using numerical methods.
Since the temperature profile at any location within the cylinder at a certain moment depends on the temperature profile at the previous moment, this problem needs to be solved iteratively. Using numerical methods, one can solve for the maximum and minimum temperatures after 4 minutes.
To know more about analysis visit:
https://brainly.com/question/32375844
#SPJ11
A wettability test is done for two different solid: Aluminum and PTFE. The surface free energies were calculated as: − −
Between Al-liquid: 70.3 J/m2
− Between liquid-vapor: X J/m2
− Between Al-vapor: 30.7 J/m2 −
− Between PTFE-liquid: 50.8 J/m2
− Between liquid-vapor: Y J/m2
− Between PTFE-vapor: 22.9 J/m2
Assuming the liquid is distilled water, Please assess the min and max values X and Y can get, by considering the material properties
The minimum value of X, the surface free energy between liquid-vapor, is estimated as the surface tension of water. The maximum value of Y, the surface free energy between liquid-vapor, depends on the contact angle of water on PTFE.
The minimum value of X, the surface free energy between liquid-vapor, can be estimated as the surface tension of distilled water, which is approximately 72.8 mJ/m^2. However, the actual value of X can vary depending on factors such as temperature and impurities in the water.
The maximum value of Y, the surface free energy between liquid-vapor, can be estimated based on the contact angle of distilled water on PTFE. PTFE is known for its low surface energy and high hydrophobicity, resulting in a large contact angle. The contact angle of water on PTFE can range from 90 to 120 degrees. Using the Young-Laplace equation, the surface free energy can be calculated, and the maximum value of Y can be estimated to be around 22.9 J/m^2.
It's important to note that these values are estimates and can vary depending on the specific experimental conditions and surface characteristics of the materials.
Learn more about vapor here:
https://brainly.com/question/15114852
#SPJ11
Which of the following statement(s) is/are invalid? float*p = new number[23]; int *p; p++;
int *P = new int; *P = 9
a+b
The second statement "int *p; p++; int *P = new int; *P = 9a+b" is invalid.
The first statement "float*p = new number[23];" is valid. It declares a pointer variable `p` of type `float*` and dynamically allocates an array of 23 elements of type `float` using the `new` operator.
The second statement "int *p; p++;" is valid syntax-wise, as it declares an integer pointer `p` and increments its value. However, it is important to note that the initial value of `p` is uninitialized, which can lead to unpredictable behavior when incremented.
The third statement "int *P = new int; *P = 9a+b;" is invalid. The expression `9a+b` is not valid in C++ syntax. The characters `a` and `b` are not recognized as valid numeric values or variables. It seems like there might be a typographical error or missing code. To be valid, the expression should use valid numeric values or variables for `a` and `b`, or it should be modified to follow the correct syntax.
In conclusion, the second statement "int *p; p++; int *P = new int; *P = 9a+b" is invalid due to the invalid expression `9a+b`, which does not conform to the syntax requirements of C++.
Learn more about p++ here:
https://brainly.com/question/30167681
#SPJ11
Digital Electronics Design Design and implement a state machine (using JK flip-flops) that functions as a 3-bit sequence generator that produces the following binary patterns. 001/0,010/0, 110/0, 100/0, 011/0, 111/1 [repeat] 001/0,010/0...... 111/1. [repeat)... Every time the sequence reaches 111. the output F will be 1. Table below shows the JK State transition input requirements. Q Q+ J K 0 0 0 X 0 1 1 X 1 0 X 1 1 1 X 0 10 4 points Design and Sketch the State Transition Diagram (STD) You may take a photo of your pen and paper solution and upload the file. You can also use excel or word. Drag n' Drop here or Browse 11 4 points ALEE Paragraph Explain why the design is safe. BIU A X' EE 12pt
A state machine is the best way to model complex real-time systems. A state machine provides a logical and concise way to specify the behavior of an object or system
Digital Electronics Design The state machine using JK flip-flops that functions as a 3-bit sequence generator which produces the following binary patterns are mentioned below Every time the sequence reaches 111, the output F will be 1.State Transition Diagram (STD):The above diagram shows the transition of the state machine using JK flip-flops.
It is clearly visible from the diagram that when the circuit receives the input 111, the output F becomes 1.Below is the explanation of why the design is safe:There are various reasons that explain why the design is safe. Some of the important reasons are mentioned below.
To know more about state machine visit:
https://brainly.com/question/30770911
#SPJ11
2. Describe the circuit configuration and what happen in a transmission line system with: a. RG = 0.1 Q b. Z = 100 Ω c. ZT 100 2 + 100uF = Design precisely the incident/reflected waves behavior using one of the methods described during the course. Define also precisely where the receiver is connected at the end of the line (on ZT)
The incident/reflected wave behaviour in a transmission line system with RG = 0.1 Q, Z = 100 Ω, and ZT = 100 2 + 100uF can be determined using the Smith chart method. The receiver is connected at the end of the line, on the load impedance ZT is the answer.
The circuit configuration and what happens in a transmission line system with RG = 0.1 Q are explained below- Transmission line system: A transmission line system is one that transfers electrical energy from one location to another. A transmission line is a two-wire or three-wire conductor that carries a signal from one location to another. These wires are generally separated by an insulator. The voltage and current in a transmission line system propagate in a specific direction, which is usually from the source to the load. When a voltage is applied to the line, it will take some time for the current to flow through the line. The time it takes for the current to flow through the line is referred to as the propagation delay.
RG = 0.1 Q: When the value of RG is 0.1 Q, it means that the transmission line has a small resistance. A small value of RG implies that the line has low losses and can carry more power. The power loss in a transmission line is proportional to the resistance, so the lower the resistance, the lower the power loss.
Z = 100 Ω:Z is the characteristic impedance of the transmission line. It is the ratio of voltage to current in the line. When the value of Z is equal to the load impedance, there is no reflection. When Z is greater than the load impedance, there is a reflection back to the source. When Z is less than the load impedance, there is a reflection that is inverted.
ZT 100 2 + 100uF =: ZT is the total impedance of the transmission line. It is equal to the sum of the characteristic impedance and the load impedance. When a transmission line is terminated with a load, there are incident and reflected waves. The incident wave is the wave that travels from the source to the load. The reflected wave is the wave that is reflected back from the load to the source.
In conclusion, the incident/reflected wave behaviour in a transmission line system with RG = 0.1 Q, Z = 100 Ω, and ZT = 100 2 + 100uF can be determined using the Smith chart method. The receiver is connected at the end of the line, on the load impedance ZT.
know more about Smith chart method.
https://brainly.com/question/30321378
#SPJ11
A commercial Building, 60hz, Three Phase System, 230V with total highest Single Phase Ampere Load of 1,288 Amperes, plus the three-phase load of 155Amperes including the highest rated of a three-phase motor of 30HP, 230V, 3Phase, 80Amp Full Load Current. Determine the Following through showing your calculations. (60pts) a. The Size of THHN Copper Conductor (must be conductors in parallel, either 2 to 5 sets), TW Grounding Copper Conductor in EMT Conduit. b. The Instantaneous Trip Power Circuit Breaker Size c. The Transformer Size d. Generator Size
The electrical requirements commercial building, the following sizes are: a) THHN copper conductors in parallel (2 to 5 sets), b) an instantaneous trip power circuit breaker, c) a transformer, and d) a generator.
a) The size of THHN copper conductors: The total single-phase load is 1,288 Amperes, which includes the three-phase load of 155 Amperes. To determine the size of the THHN copper conductors, we need to consider the highest single-phase load, which is 1,288 Amperes. Since there is no specific gauge mentioned, we can choose to use multiple conductors in parallel to meet the load requirements.
The appropriate conductor size can be determined based on the ampacity rating of THHN copper conductors, considering derating factors, ambient temperature, and installation conditions. It is recommended to consult the National Electrical Code (NEC) or a qualified electrical engineer to determine the specific number and size of parallel conductors.
b) The instantaneous trip power circuit breaker size: To protect the electrical system and equipment from overcurrent conditions, an instantaneous trip power circuit breaker is required. The size of the circuit breaker should be selected based on the maximum load current. In this case, the highest rated three-phase motor has a full load current of 80 Amperes. The circuit breaker should be rated slightly higher than this value to accommodate the motor's starting current and provide necessary protection.
c) The transformer size: The transformer size depends on the total load and the system configuration. Considering the highest single-phase load of 1,288 Amperes and the three-phase load of 155 Amperes, a transformer should be selected with appropriate kVA (kilovolt-ampere) rating to meet the load requirements. It is important to consider factors such as power factor, efficiency, and any future load expansions while choosing the transformer size.
d) The generator size: To ensure a reliable power supply during power outages, a generator is recommended. The generator size should be based on the total load of the building, including both the single-phase and three-phase loads. The generator should be selected to handle the maximum load demand with an appropriate safety margin. It is advisable to consult with a qualified electrical engineer or generator supplier to determine the specific generator size based on the load requirements and expected operational conditions.
Learn more about power circuit breaker here:
https://brainly.com/question/31061632
#SPJ11
The energy of some molecules has three values: 0, 300, and 600 cm*. In the presence of a gas consisting of 1 mole of these molecules, predict the temperature at which the proportion of molecules whose energy is intermediate is 0.15.
To determine the temperature at which the proportion of molecules with intermediate energy is 0.15, we can utilize the Boltzmann distribution and the concept of thermal equilibrium.
The Boltzmann distribution describes the distribution of molecular energies in a gas at thermal equilibrium. In this case, we have molecules with three energy levels: 0 cm⁻¹, 300 cm⁻¹, and 600 cm⁻¹. Let's denote the number of molecules with energies 0, 300, and 600 cm⁻¹ as N₀, N₃₀₀, and N₆₀₀, respectively. At thermal equilibrium, the proportion of molecules in each energy state is given by the Boltzmann distribution formula:
P(E) = (1/Z) * exp(-E/(kT))
where P(E) is the probability of a molecule having energy E, Z is the partition function, k is Boltzmann's constant, and T is the temperature.
To find the temperature at which the proportion of molecules with intermediate energy (300 cm⁻¹) is 0.15, we need to solve for T. Let's denote the proportion of molecules with energy 300 cm⁻¹ as P₃₀₀. We can set up the equation:
P₃₀₀ = (1/Z) * exp(-300/(kT))
Given that P₃₀₀ = 0.15, we can rearrange the equation to solve for T:
T = -300 / (k * ln((1/Z) * P₃₀₀))
where ln represents the natural logarithm. By substituting the appropriate values for k and P₃₀₀, we can calculate the temperature T.
learn more about Boltzmann distribution here:
https://brainly.com/question/31833642
#SPJ11
A converter works with input voltage of 220V, 60Hz. The load has an R=12ohm and an inductance of 45mH. The output voltage frequency is 20Hz and the firing angle is 135ᵒ. Calculate:
a) the output/input frequency ratio
b) the rms output voltage
c) the power dissipated in the load
A converter works with input voltage of 220V, 60Hz. The load has an R=12ohm and an inductance of 45mH. The output voltage frequency is 20Hz and the firing angle is 135ᵒ.
The output/input frequency ratio.The frequency ratio is given by;
[tex]fout/fin = Vout/Vin[/tex].
Where;
[tex]fin = 60HzVin = 220Vf_out = 20HzV_out = V_in * sin(α)[/tex].
[tex]Frequency ratio = 20/(220*sin(135)) = 0.037[/tex].
b) the rms output voltageRMS voltage is given by;[tex].
Vrms = Vp / √2[/tex]
Where;
[tex]V_p = peak voltage = V_in * sin(α)[/tex].
[tex]RMS voltage = V_in * sin(α) / √2= 220 * sin(135) / √2= 110 Vc)[/tex].
the power dissipated in the loadThe formula for power is given as
[tex];P = I_rms²RWhere;R = 12ohmL = 45mHf = 20HzV_rms = 110V[/tex].
Peak current is given by;[tex]I_p = V_p / √(R² + (2πfL)²)I_p = 110 / √(12² + (2π*20*(45*10⁻³))²)I_p = 3.07[/tex].
ARMS current is given by;
[tex]I_rms = I_p / √2I_rms = 3.07 / √2Power = (3.07 / √2)² * 12Power = 67.52 W[/tex].
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
For the circuit shown in the figure, assume that switches S 1
and S 2
have been held closed for a long time prior to t=0. S 1
then opens at t=0. However, S 2
does not open until t=48 s. Also assume R 1
=19ohm,R 2
=46ohm,R 3
=17ohm,R 4
=20ohm, and C 1
=C 2
=4 F. Problem 05.045.b Find the time constant T for 0
The given circuit is shown in the figure. For the circuit given below, consider switches S1 and S2 to be closed for a very long time prior to t=0. At t=0, S1 is opened, but S2 remains closed until t=48 seconds.
Furthermore, consider [tex]R1=19Ω, R2=46Ω, R3=17Ω, R4=20Ω, and C1=C2=4F.[/tex] Determine the time constant T for [tex]t>0, R1=19ohm, R2=46ohm, R3=17ohm,[/tex] R4=20ohm, and C1=C2=4F. In order to calculate the time constant T, use the below formula.T= equivalent resistance × equivalent capacitance.
In the given circuit, the equivalent capacitance of the two capacitors in series can be determined as follows:
[tex]C= C1*C2/(C1+C2) = 2 F[/tex].The resistors R2 and R3 are in series and can be simplified to a single resistance of [tex]R23= R2+R3= 63Ω.[/tex]The given circuit is redrawn below:The equivalent resistance can be obtained as follows:[tex]Req= R1+R4+R23 = 102ΩT[/tex].
Thus, using the formula,T= equivalent resistance × equivalent capacitance= 102 × 2= 204 s.The time constant T is 204 s.
To know more about switches visit:
brainly.com/question/30675729
#SPJ11