How are static and passive stretching similar?

Answer:

1) Given acceleration due to gravity as 10N/kg

N/kg is the same as m/s². From W=mg

making g subject ... you have g = W/m

where m is in kg and W is in N

hence we have N/kg

So g=10ms-²

Gravitational Potential Energy=mgh

At height 4m

PE=6 x 10 x 4

=240J.

At height 6m

PE=6 x 10 x 6

=360J.

2) KE=1/2mv²

=1/2 x 6 x 5² =75J

When the speed is doubled... it becomes 2x

so V = 2x5=10ms-¹

KE=1/2 x 6 x 10² =300J.

3) KE=1/2mv²

KE is given as 100J

mass=0.5kg

Making V the subject

you have v² =2KE/m

v²=2 x 100/0.5

v²=400

taking square root

v=20ms-¹.

Have a great day✌

The friction force required to keep the car from sliding is 9000N.

mass of car, m = 1000 kg

speed , v = 30 m/s

diameter , d = 0.2 km

r = 100 m

for the car to keep from sliding frictional force is required, ff = m*v^2/r

ff = 1000 * 30^2 /100

ff = 9000 N

the friction force required is 9000 N

Simply put, an unbanked curve (or turn) is a curve that is flat on the ground (parallel to the horizontal). A force of friction applies to the car as it drives along one of these curves, keeping it rotating in a circular course.

to know more about friction force here:

brainly.com/question/30280752

#SPJ4

The maximum height the diving board can be above the water is 52.5m, so that she does not go any faster than 32 m/s when she enters the water.

To determine the maximum height the diving board can be above the water, we can use the equation of motion for a freely falling object:

v^2 = u^2 + 2as

where

v = final velocity (32 m/s)

u = initial velocity (0 m/s)

a = acceleration due to gravity (-9.8 m/s^2)

s = distance fallen (height of diving board above water)

We can rearrange the equation to find the distance fallen (s)

s = v^2/(-2a) - u^2/2a

substituting the values

s = 32^2/(-2*(-9.8)) = 32^2/19.6 = (1024/19.6) = 52.5 m

To know more about acceleration visit:

brainly.com/question/980919

#SPJ4

This electricity is then directed from the electric generator to electric outlets in homes

A power source that creates electricity through the use of giant magnets that are rotated to create a flow of electrons is called a generator. Generators use the principle of electromagnetic induction to convert mechanical energy (rotational energy of the magnets) into electrical energy.The electricity generated by the generator is then directed through electrical transmission lines to a substation, where it is transformed to a higher voltage level for long-distance transmission. Then it is distributed to homes and businesses through power lines and transformers.

Learn more about mechanical energy here:

https://brainly.com/question/28928306

#SPJ4

According to the given statement The temperature of the air in this experiment is dependent variable.

Material refers to a thing that something else is made out of. Material can also refer to cloth or can be used to describe something that is made of matter and exists in the physical world. Material has many other senses as a noun and an adjective.

A material is any substance that an object is made from. Glass, chalk, paper, wax, water, air, clay and plastic are all different materials. All materials are made up of matter.

To know more about material visit:

brainly.com/question/9176437

#SPJ4

Answer:

because potential energy is the kinetic energy something COULD have. Like when a rollercoaster is about to go over a bump, before it goes down it has potential energy, then when it goes it accelerates and creates kinetic energy. That rock be zero cause it has no potential

Explanation:

Answer: yeah for sure but post the picture

Explanation:

Lol

So because acceleration of freely falling objects is constant, if a 5 kilogram object starts free falling at rest, its acceleration at 3 seconds is g=9.8 m/s2 or 32.2 ft/s2.

As the gravitational pull of an object changes as it is moved further away from Earth or placed on another planet, so does the object's weight. Regardless of whether an object is on Planet, in deep space, or on the Moon, its mass will always be the same.

For  the gravitational force the formula is P.E. = mgh, where m is the mass in kilograms, g is the acceleration due to gravity (9.8 m / s2 at the surface of the earth) and h is the height in meters. Notice that gravitational potential energy has the same units as kinetic energy, kg m2 / s2.

TO know more about acceleration  visit :

https://brainly.com/question/12550364

#SPJ4

From the graph,

Vmax = 3V

Vavg = 2*Vmax/π = 2*3/π = 1.91 V

Vrms = Vmax/√2 = 3/√2 = 2.121 V

Note: The graph that has been considered for theses calculation, is uploaded as an attachment along with the answer.

The sine wave can achieve a maximum value known as VMax for both negative and positive directions. It is VMax for a positive cycle and (-)VMax for a negative cycle.

The average of the instantaneous voltages selected at correctly spaced intervals during the half - cycles of an AC sinusoidal (or other periodic) waveform is the average voltage. The average value is a representation of the area beneath the AC wave form as a function of time.

A sinusoidal origin of electromotive force is described by its root-mean-square (rms) voltage (Vrms), denoted by Vmax/√2.

To know more about the Voltage calculation here:

https://brainly.com/question/891089#

#SPJ4

Answer:

Cellular respiration is a metabolic pathway that breaks down glucose and produces ATP. The stages of cellular respiration include glycolysis, pyruvate oxidation, the citric acid or Krebs cycle, and oxidative phosphorylation.

Explanation:

Answer:

Cellular respiration takes in food and uses it to create ATP, a chemical which the cell uses for energy. Usually, this process uses oxygen, and is called aerobic respiration. It has four stages known as glycolysis, Link reaction, the Krebs cycle, and the electron transport chain

hope this helps

have a good day :)

Explanation:

Answer:

The amount of work done is 45 J.

Explanation:

We know that the force applied is 15N. The amount of displacement experienced by the box is 3 metres along the floor.

Thus, F= 15N

D= 3 metres

The formula for calculating work done is W= F×D

Thus, W=15×3

W=45J

Thus, the amount of work done is 45J.

Answer:

the speed of the satellite is 12,880.53 km/h

Explanation:

Given;

radius of the circular orbit, r = 24,600 km

time taken to revolve around Earth, t = 12 hours

The circumference of the satellite is calculated as;

L = 2πr

L = 2π x 24,600 km

L = 49,200π km

L = 154,566.36 km

The speed of the satellite;

v = L/t

v = 154,566.36 / 12

v = 12,880.53 km/h

Therefore, the speed of the satellite is 12,880.53 km/h

He accomplished no job. When Taylor's car broke down, he attempted to push it with 8,000 newtons of force before giving up and calling a tow truck.

The mechanical advantage is how many times a machine can multiply the force of the effort. The mechanical advantage of the machine increases when the effort force is exerted across a bigger distance.

Force multipliers are tools that lessen the force required to move an object. Force multipliers come in handy when lifting heavy objects or performing other actions that call for a lot of force.

To know more about force visit:-

https://brainly.com/question/13191643

#SPJ4

Explanation:

Distance is 250m

Time is 50sec

Formular

Speed= distance/time

Speed=250/50

Speed is 5m/s

If correct mark as brainliest

Answer:

[tex]\boxed {\boxed {\sf 5 \ m/s}}[/tex]

Explanation:

Speed is the rate an object moves. It is found by dividing the distance by the time.

[tex]s=\frac{d}{t}[/tex]

Kenny and Chris walked a distance of 250 meters in 50 seconds. So:

Substitute the values into the formula.

[tex]s=\frac{250 \ m}{ 50 \ s}[/tex]

Divide.

[tex]s= 5 \ m/s[/tex]

Kenny and Chris had an average speed of 5 meters per second.

The objects must be of opposite charge because the electric force of attraction between them increases when they are released and free to move.

This means that the electric force must be a repulsive force that pushes the objects away from each other. Opposite charges attract and as charges repel, the objects must be of opposite charge for the electric force to increase when the objects are released and free to move.

Therefore when two small objects carry the same amount of charge, the magnitude of the electric force exerted by one object on the other is 0.10 N when they are held 30 mm apart. If the force magnitude increases when the objects are released and free to move, then we can say that they are opposite charges.

Learn more about charge:

https://brainly.com/question/25923373

#SPJ4

Answer:

Not including a sedimentary cover of variable thickness and composition, the oceanic crust consists of three layers: (1) a relatively thin uppermost volcanic layer of basaltic lavas known as mid-ocean ridge basalts (MORB) erupted on the seafloor; (2) a thicker layer of more coarsely crystalline, intrusive basaltic 

The formula for k in terms of the period T and the mass m in spring constant problem is k = 4π²m/T². The formula applies to a spring-mass system.

A spring-mass system is a system where a mass of object is attached at the free end of the spring. The system will perform a simple harmonic motion where the oscillations occur periodically. The period of any moving object in that motion can be counted as follows

T = 2π√(m/k)

Where

Find the formula for the spring constant k in terms of T and m!

We use the formula above to find k.

T = 2π√(m/k)

√(m/k) = T/2π

m/k = (T/2π)²

m/k = T²/4π²

k = 4π²m/T²

Hence, the formula for the spring constant in the spring-mass system is k = 4π²m/T². The answer is A.

Learn more about spring mass system here:

brainly.com/question/9434528

#SPJ4

he JM will heighten (exaggerate) lower limb tendon reflexes by countering some of the normal descending inhibition the brain sends to the reflex arc.

A medical technique called the Jendrassik manoeuvre involves the patient clenching their teeth, flexing both sets of fingers into a hook-like shape, and interlocking those sets of fingers. The patellar reflex is then induced by striking the tendon below the patient's knee with a reflex hammer.

When the technique is not being used, the reflex outcome of the same movement is compared to the induced reaction. When a patient is focused on the technique, a bigger reflex reaction is frequently seen: "Afferent activity brought on by such muscle tension may activate a weak or seemingly absent reflex.

This is the actual justification for the procedure, not that it is intended to divert the patient's attention, a common misperception that persists to this day." This result

To be learn more about procedure refer to:

https://brainly.com/question/27176982?referrer=searchResults

#SPJ1

Potential energy is the power that a thing possesses as a result of where it is in relation to other objects.

The earth can pull you down through the force of gravity while doing work in the process, being at the top of a stairwell gives you more potential energy than standing at the bottom.

Two magnets have more potential energy when they are held apart than when they are near to one another. They will migrate near each other and begin working if you let them go.

The force acting on the two objects affects the potential energy formula. P.E. = mgh, where m is the mass in kilograms and g is the acceleration due to gravity, is the formula for gravitational force.

Therefore, Potential energy is the power that a thing possesses as a result of where it is in relation to other objects.

To learn more about Potential energy, refer to the link:

https://brainly.com/question/24284560?

#SPJ1

Answer: The length of the pendulum is approximately 2.495 meters.

Explanation:

The period of a simple pendulum is the time it takes for the pendulum to swing back and forth through one full oscillation. The period of a simple pendulum is related to the length of the pendulum and the acceleration due to gravity (g) by the formula:

Period = 2 * pi * sqrt(length / g)

In this case, you are given that the period of the pendulum is 3 seconds and the value of g is 9.98 ms-2. You can use these values to solve for the length of the pendulum using the formula above.

Substituting in the values given, you get:

3 = 2 * pi * sqrt(length / 9.98)

Solving for length, you get:

length = (3 / (2 * pi))^2 * 9.98

= 0.5^2 * 9.98

= 0.25 * 9.98

= 2.495

Therefore, the length of the pendulum is approximately 2.495 meters.

A body's mass is the total amount of its material. Gravitational pull on a body is represented by weight.

The relationship between mass and weight Mass is a measure of inertia, whereas weight is a measure of force.

Both of these names are frequently used in the same sentence. Calculating how much matter a body contains requires knowing its mass.

Weight is a unit of measurement for the force that gravity's acceleration has on a mass.

Weight is a measurement of how the force of gravity works upon a mass, whereas mass is a measure of the amount of matter in a material.

In order to determine how much matter a body contains, we need to use its mass.

To learn more about mass and weight refer to:

brainly.com/question/1966951

#SPJ4

The correct option is A, B, and C. A block resting on a slope is Weight, static friction, and Normal force.

Static friction is a force that continues an item at relaxation. Static friction definition can be written as: The friction skilled while individuals try to move a desk-bound object on a surface, without surely triggering any relative movement between the frame and the surface on which it's miles.

Static friction is a form of friction force that acts on a body when there's no relative motion between the object and the surface. So, it can act even if the frame is in motion however there should be no relative motion.

A pressure acting on an item is said to be a static force if it no longer exchanges the scale, function, or route of that precise object. The pressure implemented to a structure acts as a load to that precise structure, that is why static force is likewise called a static load.

To learn more about Static friction visit here:

brainly.com/question/13000653

#SPJ4

Complete Question:

A block is resting on a slope. (Figure 3) Which of the following forces act on the block?

Check all that apply.

A). Weight

B). Static friction

C). Normal force

D). Kinetic friction

E). Force of push

The coefficient of static friction between the crate and the floor is calculated to be 0.275.

The frictional force when an object moves on the horizontal surface is given as,

Ff = μ N

where, N is the normal force

μ is the coefficient of static or kinematic friction

If no forces other then the weight and the normal are acting upon the y-direction, then the weight and the normal force are equal in magnitude.

N = W = m g

Given that,

Mass of the crate = 26 kg

Frictional force Ff = 70 N

Weight of the crate = 26 × 9.8 = 254.8 N

The normal force is 254.8 N.

The coefficient of static friction μ = Ff /N = 70/254.8 = 0.275

Thus, the coefficient of static friction between the crate and the floor is 0.275.

To know more about friction:

https://brainly.com/question/20162979

#SPJ4

Torque =   force x distance from point of rotation

Torque is a measure of the turning effect of an applied force about a specific point or axis. It is calculated by multiplying the force applied to an object by the distance from the point of rotation to the point where the force is applied. The greater the force or the longer the distance from the point of rotation, the greater the torque. The unit of torque is typically Newton-meters (N·m) in the International System of Units (SI) or pound-feet (lb·ft) in the imperial system. Torque is essential in various fields such as physics, mechanics, engineering and robotics.

To know more about Torque click below:

https://brainly.com/question/6855614#

#SPJ4

She moves at 6.5 m/s as her final speed after running 100 meters.

The velocity change of an object per unit of time is known as acceleration. Amounts of acceleration are measured in meters per second squared (m/s2), the SI unit of acceleration. For instance, due to Earth's gravity, a falling object accelerates at a rate of 9.8 m/s2.

A straight-line motion issue looks something like this. These formulas are used to determine the final velocity:

s = Vo*t + (1/2)*a*at2, and Vf = Vo + at

Where:

Vf = = final speed =?

1.4 m/s is the initial velocity, and 0.20 m/s is the acceleration.

100m displacement in 2 seconds.

the first equation is changed by:

100 = 1.4t + (1/2)*0.2*t^2\st = 25.388s

Vf = 1.4 + 0.2 can be used as a replacement in the second equation.

Vf = 6.5m/s

To know more about cardio exercise visit:-

https://brainly.com/question/1311324

#SPJ4

The final velocity of the freight train is 27 m/s that accelerates at a rate of 0.050 m/s2 for 8.0 min, starting with an initial velocity of 3.0 m/s.

Information given:

Acceleration is 0.050 m/s²

Time is 8.0 min

Initial velocity is 3.0 m/s

We apply the resulting equations for rectilinear motion at constant acceleration to this problem.

a = (v - u)/t

where the,

a is acceleration

u and v are the initial and final velocities, respectively

s is the distance

t is the time

Substituting the values in the equation:

The solution is as follows:

a = (v - v₀)/t

0.050 m/s² = (v - 3 m/s)/(8 min * 60 s/1 min)

Time: 480 sec

Solving for v,

24=v-3

v=27 m/s

Learn more about acceleration:

brainly.com/question/28743430

#SPJ4

Answer:

378 N

Explanation:

F = ma = (63 kg)(6 m/s²) = 378 N

A skier weighing 63 kg needs 189N of force to accelerate at 6 m/s. The magnitude of the force required to accelerate the sled is 91 newtons.

An object's acceleration is equal to the net force acting on it divided by its mass, or a = F m, according to Newton's second law of motion. When the object's mass and the net force it is subjected to are known, this acceleration equation can be used to determine its acceleration.

By the second law of Newton, F = ma Add the following numbers:

F=189N F=63kg(2ms 2)

Formula for acceleration: there are three equations for acceleration:

To learn more about Newton's second law here:

https://brainly.com/question/13447525

#SPJ1

A. The nature of the image of 5th Avenue in the mirror sculpture is that it is a virtual, upright, and smaller image. This is because the concave mirror is used to reflect light outwards, creating a virtual image that cannot be projected onto a screen.

B. The property of concave mirrors that is utilized for using them as shaving mirrors is their ability to form a smaller, magnified image. This is because concave mirrors have a negative focal length, which causes light rays to diverge and form a smaller image that is closer to the mirror.

C. To determine the focal length of the mirror, we can use the formula 1/f = 1/u + 1/v, where f is the focal length, u is the object distance (38 meters), and v is the image distance (unknown). We know that the image size is 1/5 the size of the object, so we can set v = -5u (since the image is virtual and inverted). Substituting these values into the formula and solving for f, we get f = -(5u^2)/4 = -(5(38^2))/4 = -4725/4 = -1181.25 meters.

D. To estimate the image size of the 270 meter tall Rockefeller Centre, we can use the formula: h' = -h * (u/f) where h' is the image height, h is the object height (270 meters), u is the object distance (100 meters) and f is the focal length (10 meters). Substituting these values in the formula, h' = -270 * (100/10) = -2700 meters. This means the image of the Rockefeller Centre would be 2700 meters tall, which is not possible because it's taller than the building itself. This is an indication that the image is not real and is a virtual image.

Unlike plane mirrors, spherical mirrors form images that are different in size from the size of the object. While the convex mirror forms images that are always smaller than the object, the concave mirror forms images of different sizes, depending on the position in which the object is placed on its axis.

Learn more about convex mirror in brainly.com/question/11627506

#SPJ1