Light of 580 nm passing through a single slit, shows a diffraction pattern on a screen 4.50 m behind the all
as the one in the graph below.
a) What is the width of the central maximum?
b) Can we consider small angle approximation? Consider first minimum for order of magnitude (show
calculations that support your answer)
c) What is the width of the slit?
d) What is the distance from the central maximum to the 5th minimum?
e) If the length between the screen and the slit was increased, would the central maximum get wider,
narrower or it will not change?
f) If the width of the slit was increased, would the central maximum get wider, narrower or it will not
change?
The graph:
Question 2: The camera of a satellite has a diameter of 40cm. The satellite is orbiting 250 km from the surface of earth. What is the minimum distance 2 objects could be on the surface of earth to be result by this camera? Consider 500 cm light.

The ochre sea star (Pisaster ochraceus) belongs to the Asteroidea class of the phylum Echinodermata. It is characterized by its radial symmetry and has a flat, star-shaped body with five spokes radiating from its center.

Asteroidea is a class within the phylum Echinodermata, which includes starfish or sea stars. Animals in the Asteroidea class have five or more arms that radiate from a central disk. They can be found in various marine habitats across the world's oceans, ranging from the deep sea to intertidal zones.

Apart from Asteroidea, the phylum Echinodermata also includes other classes such as Crinoidea (sea lilies and feather stars), Echinoidea (sea urchins and sand dollars), Holothuroidea (sea cucumbers), and Ophiuroidea (brittle stars and basket stars). Each class within the phylum exhibits unique characteristics and adaptations for their specific habitats and lifestyles.

Learn more about ochre sea star

https://brainly.com/question/30093147

#SPJ11

The power emitted by a monochromatic source is 6.3 m Wavelength of light emitted by the source is 600 nm.

1. Energy of photon, E = hc/λ

where, h = Planck's constant = 6.63 × 10⁻³⁴ Js, c = Speed of light = 3 × 10⁸ m/s, λ = wavelength of light= 600 nm = 600 × 10⁻⁹ m

Substitute the values, E = (6.63 × 10⁻³⁴ J.s × 3 × 10⁸ m/s)/(600 × 10⁻⁹ m) = 3.31 × 10⁻¹⁹ J1 eV = 1.6 × 10⁻¹⁹ J

Hence, Energy of photon in eV, E = (3.31 × 10⁻¹⁹ J)/ (1.6 × 10⁻¹⁹ J/eV) = 2.07 eV (approx.)

2. The power is given by,

P = Energy/Time Energy, E = P × Time Where P = 6.3 mW = 6.3 × 10⁻³ W, Time = 10 minutes = 10 × 60 seconds = 600 seconds

E = (6.3 × 10⁻³ W) × (600 s) = 3.78 J

Number of photons emitted, n = E/Energy of each photon = E/E1 = 3.78 J/3.31 × 10⁻¹⁹ J/photon ≈ 1.14 × 10²¹ photons

3. The work function (ϕ) of a metal is the minimum energy required to eject an electron from the metal surface. It is given by the relation, K max = hv - ϕ where Kmax = Maximum kinetic energy of the ejected electron, v = Frequency of the incident radiation (v = c/λ), and h = Planck's constant.

Using Kmax = 0.55 eV = 0.55 × 1.6 × 10⁻¹⁹ J, h = 6.63 × 10⁻³⁴ Js, λ = 600 nm = 600 × 10⁻⁹ m,v = c/λ = 3 × 10⁸ m/s ÷ 600 × 10⁻⁹ m = 5 × 10¹⁴ s⁻¹.

Substituting all the values in the above formula,ϕ = hv - Kmaxϕ = (6.63 × 10⁻³⁴ Js × 5 × 10¹⁴ s⁻¹) - (0.55 × 1.6 × 10⁻¹⁹ J)ϕ ≈ 4.3 × 10⁻¹⁹ J

Therefore, the work function of the metal is approximately equal to 4.3 × 10⁻¹⁹ J.

Explore another question on work function of metals: https://brainly.com/question/19427469

#SPJ11

After 2 time constants, the current across the inductor will be approximately 5.320 Amperes. The current across the inductor after 2 time constants, we need to calculate the time constant and then use it to find the current at that time. The time constant (τ) of an RL circuit (resistor-inductor circuit) is given by the formula:

τ = L / R,

where L is the inductance and R is the resistance.

First, let's calculate the inductance of the coil. The inductance of a tightly packed solenoid can be approximated using the formula:

L = (μ₀ * N² * A) / l,

where μ₀ is the permeability of free space (4π x [tex]10^-7[/tex]T·m/A), N is the number of turns, A is the cross-sectional area of the solenoid, and l is the length of the solenoid.

Number of turns, N = 60,000

Cross-sectional area, A = π * ([tex]0.0200 m)^2[/tex]

Length of the solenoid, l = 0.0100 m

Using these values, we can calculate the inductance:

L = (4π x [tex]10^-7[/tex]T·m/A) * ([tex]60,000 turns)^2[/tex] * (π * [tex](0.0200 m)^2[/tex]) / 0.0100 m

≈ 0.301 T·m²/A

Next, we can calculate the time constant:

τ = L / R = 0.301 T·m²/A / 0.325 Ω

≈ 0.926 s

Now, we can determine the current after 2 time constants:

I(t) = I(∞) * (1 - e^(-t/τ)),

where I(t) is the current at time t, I(∞) is the final current (as t approaches infinity), and e is the base of the natural logarithm.

Since t = 2τ, we can substitute this value into the equation:

I(2τ) = I(∞) * (1 - e^(-2))

≈ I(∞) * (1 - 0.1353)

≈ I(∞) * 0.8647

We are given that the voltage source is 2.00 Volts. Using Ohm's law (V = I(∞) * R), we can solve for I(∞):

2.00 V = I(∞) * 0.325 Ω

I(∞) = 2.00 V / 0.325 Ω

≈ 6.153 A

Finally, we can calculate the current after 2 time constants:

I(2τ) ≈ I(∞) * 0.8647

≈ 6.153 A * 0.8647

≈ 5.320 A

Therefore, after 2 time constants, the current across the inductor will be approximately 5.320 Amperes.

Learn more about current here:

https://brainly.com/question/13757528

#SPJ11

The correct statement is that c. the copper core heats up because circular currents around its axis are induced in the core.

What is a solenoid?

A solenoid is a long coil of wire with numerous turns that are tightly packed together. It produces a uniform magnetic field when electrical energy is passed through it. An electric current flowing through a solenoid produces a magnetic field that is proportional to the number of turns in the coil and the magnitude of the electric current.

The statement, "The copper core heats up because circular currents around its axis are induced in the core" is correct. The magnetic field produced by the solenoid induces circular currents in the copper core. These circular currents are referred to as eddy currents. The eddy currents heat up the copper core and, as a result, the copper core becomes hot.

To learn more circular currents, refer:-

https://brainly.com/question/30874979

#SPJ11

Photons of wavelength 450 nm are incident on a metal. The most energetic electrons ejected from the metal are bent into a circular arc of radius 20.0 cm by a magnetic field with a magnitude of 2.00 x 10^-5 T.The work function of the metal is approximately 2.45 x 10^-19 J.

To determine the work function of the metal, we can use the relationship between the energy of a photon and the work function of the metal.

The energy of a photon can be calculated using the equation:

E = hc/λ

Where:

E is the energy of the photon,

h is Planck's constant (approximately 6.626 x 10^-34 J·s),

c is the speed of light (approximately 3.00 x 10^8 m/s), and

λ is the wavelength of the photon.

Given that the wavelength of the incident photons is 450 nm (450 x 10^-9 m), we can calculate the energy of each photon.

E = (6.626 x 10^-34 J·s)(3.00 x 10^8 m/s) / (450 x 10^-9 m)

E = 4.42 x 10^-19 J

The energy of each photon is 4.42 x 10^-19 J.

Now, let's consider the electrons being bent into a circular arc by the magnetic field. The centripetal force on the electrons is provided by the magnetic force, given by the equation:

F = q×v×B

Where:

F is the magnetic force,

q is the charge of the electron (approximately -1.60 x 10^-19 C),

v is the velocity of the electrons, and

B is the magnitude of the magnetic field (2.00 x 10^-5 T).

The centripetal force is also given by the equation:

F = mv^2 / r

Where:

m is the mass of the electron (approximately 9.11 x 10^-31 kg), and

r is the radius of the circular arc (20.0 cm or 0.20 m).

Setting these two equations equal to each other and solving for v:

qvB = mv^2 / r

v = qBr / m

Substituting the known values:

v = (-1.60 x 10^-19 C)(2.00 x 10^-5 T)(0.20 m) / (9.11 x 10^-31 kg)

v ≈ -0.704 x 10^6 m/s

The velocity of the electrons is approximately -0.704 x 10^6 m/s.

Now, we can calculate the kinetic energy of the electrons using the equation:

KE = (1/2)mv^2

KE = (1/2)(9.11 x 10^-31 kg)(-0.704 x 10^6 m/s)^2

KE ≈ 2.45 x 10^-19 J

The kinetic energy of the electrons is approximately 2.45 x 10^-19 J.

The work function (Φ) is defined as the minimum energy required to remove an electron from the metal surface. Therefore, the work function is equal to the kinetic energy of the electrons.

Φ = 2.45 x 10^-19 J

Hence, the work function of the metal is approximately 2.45 x 10^-19 J.

To learn more about Photons visit: https://brainly.com/question/30130156

#SPJ11

a) The power input to the compressor in the Carnot refrigeration cycle, in order to supply 2 kW of cooling to the room, will depend on the efficiency of the cycle and the heat transfer involved.

b) The net power input to the cycle can be determined by considering the work done by the compressor and the work done on the system.

a) To calculate the power input to the compressor, we need to determine the heat transfer from the groundwater to the room. The Carnot refrigeration cycle is an idealized cycle, and its efficiency is given by the equation: Efficiency = 1 - (T_evaporator / T_condenser), where T_evaporator and T_condenser are the temperatures at the evaporator and condenser, respectively. Using this efficiency, we can calculate the heat transfer from the groundwater and convert it to power input.

b) The net power input to the cycle takes into account the work done by the compressor and the work done on the system. It can be calculated by subtracting the work done by the compressor from the heat transfer from the groundwater. The work done by the compressor can be determined using the power input calculated in part a), and the heat transfer from the groundwater can be obtained using the given temperatures and the specific heat properties of the refrigerant.

Overall, the Carnot refrigeration cycle involves several calculations to determine the power input to the compressor and the net power input to the cycle, considering the heat transfer and work done in the system.

To know more about the Carnot refrigeration cycle click here:

https://brainly.com/question/29234662

#SPJ11

The direction of the magnetic force can be determined using the right-hand rule for magnetic force.

According to this rule, if the thumb of the right hand points in the direction of the velocity of the charged particle, and the fingers point in the direction of the magnetic field, then the palm of the hand will indicate the direction of the magnetic force on the particle.

(a) For a negatively charged particle moving north in a magnetic field pointing up, the force would act to the west.(b) For a positively charged particle moving in the +x direction in a magnetic field pointing in the −y direction, the force would act in the +z direction.

(c) For a positively charged particle that is stationary in a magnetic field pointing in the +z direction, there would be no magnetic force since the particle is not in motion.(d) For a negatively charged particle moving west in a magnetic field pointing east, the force would act in the south direction.

(e) For a negatively charged particle moving in the −z direction in a magnetic field pointing in the −x direction, the force would act in the +y direction.(f) For a negatively charged particle moving up in a magnetic field pointing south, the force would act in the west direction.

Learn more about magnetic force here:

https://brainly.com/question/30532541

#SPJ11

The time constant of the closed-loop system is 1/35, which is approximately equal to 0.03

To find the time constant after adding the controller Ge(s) to the system, we need to determine the transfer function of the closed-loop system. The transfer function of the closed-loop system, T(s), is given by the product of the transfer function of the plant G(s) and the transfer function of the controller Ge(s):

T(s) = G(s) * Ge(s)

In this case, G(s) = 5s + 1 and Ge(s) = Kp = 7.

Substituting these values into the equation, we get:

T(s) = (5s + 1) * 7

= 35s + 7

To find the time constant of the closed-loop system, we need to determine the inverse Laplace transform of T(s).

Taking the inverse Laplace transform of 35s + 7, we obtain:

t(t) = 35 * δ'(t) + 7 * δ(t)

Here, δ(t) is the Dirac delta function, and δ'(t) is its derivative.

The time constant is defined as the reciprocal of the coefficient of the highest derivative term in the expression. In this case, the highest derivative term is δ'(t), and its coefficient is 35. Therefore, the closed-loop system's time constant is 1/35, which is nearly equivalent to 0.03. (rounded to two decimal places).

To know more about the Transfer functions, here

https://brainly.com/question/33247304

#SPJ4

(a) The magnitude of the magnetic field at the empty corner is 3π x 10⁻⁷/d, T.

(b) The magnitude of the magnetic field at the center of the square is 0.

(a) The magnitude of the magnetic field at the empty corner is calculated as;

B = μ₀I/2πd

where;

The resultant magnetic field at the empty corner will be the vector sum of the three wire fields:

B_net =  3B

B_net = 3(4π × 10⁻⁷ × 4 / d)

B_net = 3π x 10⁻⁷/d, T

(b) The magnitude of the magnetic field at the center of the square is calculated as;

each magnetic field in opposite direction will cancel out;

B(net) = 0

Learn more about magnetic field here: https://brainly.com/question/7802337

#SPJ4

The potential energy of this 2C charge is equal to the work required to bring it from infinity to the point O. Since the potential at infinity is zero, the potential energy of the 2C charge at O is also zero.

a. The net vertical electric field at the point O is zero. There are two negative and two positive charges, with symmetrical arrangements, and so, the electric fields at O add up to zero.b.

The net horizontal electric field at the point O is zero. There are two negative and two positive charges, with symmetrical arrangements, and so, the electric fields at O add up to zero. c. The potential V at point O is zero. The potential at any point due to these charges is calculated by adding the potentials at that point due to each of the charges.

For symmetrical arrangements like the present one, the potential difference at O due to each charge is equal and opposite, and so, the potential difference due to the charges at O is zero. d. If a 2C charge is placed at O, it will experience a net force due to the charges on either side of O.

The magnitudes of these two forces will be equal and the direction of each of these forces will be towards the other charge. The two forces will add up to give a net force of magnitude F = kqQ/r^2, where k is the Coulomb constant, q is the charge at O, Q is the charge to either side of O, and r is the separation between the two charges.e.

The potential energy of this 2C charge is equal to the work required to bring it from infinity to the point O. Since the potential at infinity is zero, the potential energy of the 2C charge at O is also zero.

to know more about potential energy

https://brainly.com/question/16705765

#SPJ11

Answer: A. False  B. True  C. True  D. False  E. False  F. False  G. True

Explanation:

A. False: Hot objects are not bluer than cold objects. Hot objects actually glow red, yellow or blue, depending on how hot they are.

B. True: As the radius of an electron orbit in an atom is proportional to n2, the radius of the 3M orbit of Helium (n = 3) is greater than the radius of the 10th orbit of Boron (n = 10).

C. True: If we increase the temperature of a body by a factor of 3, the power of emitted radiation increases by 34 or 81. Therefore, the brightness increases by a factor of 81.

D. False: Decay does not involve a position.

E. False: Decay does not show that there are only some allowed electron orbits in an atom.

F. False: Decay does not happen when a proton turns into a neutron.

G. True: Alpha decay, also known as decay, is the process in which a Helium nucleus is emitted.

Learn more about Decay : https://brainly.com/question/9932896

#SPJ11

The magnitude of the electric field is 5.12 × 10^6 N/C, and it is directed upwards.

In order for the charged object to be in static equilibrium, the electric force acting on it must balance the gravitational force. The electric force experienced by the object can be calculated using the equation F = qE, where F is the force, q is the charge of the object, and E is the electric field.

Given that the mass of the object is 4.00 g (or 0.004 kg) and the charge is -19.5 μC (or -1.95 × [tex]10^{-8}[/tex] C), we can calculate the gravitational force acting on the object using the equation F_gravity = mg, where g is the acceleration due to gravity (approximately 9.8 [tex]m/s^2[/tex]).

Since the object is in equilibrium, the electric force and the gravitational force are equal in magnitude but opposite in direction. Therefore, we have F = F_gravity. Substituting the values, we get qE = mg, which can be rearranged to solve for the electric field E.

Plugging in the known values, we have (-1.95 × [tex]10^{-8}[/tex] C)E = (0.004 kg)(9.8 [tex]m/s^2[/tex]). Solving for E gives us E = (0.004 kg)(9.8 [tex]m/s^2[/tex])/(-1.95 × [tex]10^-8[/tex] C) ≈ 5.12 × [tex]10^6[/tex] N/C.

The negative charge on the object indicates that the direction of the electric field is directed upwards, opposite to the direction of the gravitational force.

Learn more about electric field here ;

https://brainly.com/question/30544719

#SPJ11

The maximum torque is 1082 Nm, which is achieved at 6.5% slip. The overload capacity is 227%. is the answer.

A 6-pole induction motor has the following specifications: U1 = 400 V, n = 970 rpm, f1 = 50 Hz, and the stator windings are connected in Y. Given the parameters r1 = 2.08 Ω, r2 = 1.53 Ω, x1 = 3.12 Ω, and x2 = 4.25 Ω, we are required to find out the following: rated slip maximum torque overload capacity

The formula for slip (s) is given by: s = (ns - nr) / ns where ns = synchronous speed

nr = rotor speed

Using the given values, we get: s = (ns - nr) / ns= (120 * f1 - nr) / (120 * f1)= (120 * 50 - 970) / (120 * 50)= 0.035 or 3.5%

This is the rated slip.

Maximum torque is achieved at the slip (s) that is 0.1 to 0.15 less than the rated slip (sr).

Hence, maximum torque slip (sm) can be calculated as follows: sm = sr - 0.1sr = rated slip sm = sr - 0.1= 0.035 - 0.1= -0.065or 6.5% (Approx)

The maximum torque is given by: T max = 3V12 / (2πf1) * (r2 / s) * [(s * (r2 / s) + x2) / ((r1 + r2 / s)2 + (x1 + x2)2) + s * (r2 / s) / ((r2 / s)2 + x2)2] where,V1 = 400 Vr1 = 2.08 Ωr2 = 1.53 Ωx1 = 3.12 Ωx2 = 4.25 Ωf1 = 50 Hz s = 0.035 (Rated Slip)

Putting all the values in the formula, we get: T max = 3 * 4002 / (2π * 50) * (1.53 / 0.035) * [(0.035 * (1.53 / 0.035) + 4.25) / ((2.08 + 1.53 / 0.035)2 + (3.12 + 4.25)2) + 0.035 * (1.53 / 0.035) / ((1.53 / 0.035)2 + 4.25)2]= 1082 Nm

Overload capacity is the percentage of the maximum torque that the motor can carry continuously.

This can be calculated using the following formula: Am = Tmax / Tn where T max = 1082 Nm

Tn = (2 * π * f1 * n) / 60 (Torque at rated speed)Putting all the values, we get: Am = Tmax / Tn= 1082 / [(2 * π * 50 * 970) / 60]= 2.27 or 227%

Therefore, the rated slip is 3.5%.

The maximum torque is 1082 Nm, which is achieved at 6.5% slip. The overload capacity is 227%.

know more about  maximum torque

https://brainly.com/question/30337233

#SPJ11

(a) The amplitude of the wave is 2.0 mm, (b) the period of the wave is 0.1 s, (c) the velocity of the traveling wave is 2 m/s,

(d) the transverse velocity at x = 2.0 mm and t = 2 ms is -40 mm/s,  

(e) time taken for a given point on the string to move between displacements of y = +1.0 mm and y = -1.0 mm is 0.025 s.

(a) The amplitude of a wave represents the maximum displacement from the equilibrium position. In this case, the amplitude is given as 2.0 mm.

(b) The period of a wave is the time taken for one complete cycle.The period (T) can be calculated as T = 2π/ω, which gives a value of 0.1 s.

(c) It is determined by the ratio of the angular frequency to the wave number (v = ω/k). In this case, the velocity of the wave is 2 m/s.

(d) The transverse velocity of a string element. Evaluating this derivative at x = 2.0 mm and t = 2 ms gives a transverse velocity of -40 mm/s.

(e) The time taken for a given point on the string to move between displacements sine function to complete one full cycle between these two points. Therefore, the total time is 0.025 s.

Learn more about amplitude here;

https://brainly.com/question/3613222

#SPJ11

Given this wavelength and frequency.  that the frequency of the first scenario is approximately 3.168 times the frequency of the second scenario.

To calculate the speed of a sound wave, we can use the formula: speed = wavelength × frequency.

For the first scenario with a wavelength of 15.4 cm, we need to convert it to meters by dividing it by 100: 15.4 cm = 0.154 m. Let's assume a frequency of f1. Using the formula, we have speed = 0.154 m × f1.

For the second scenario with a wavelength of 48.7 cm, we again convert it to meters: 48.7 cm = 0.487 m. Let's assume a frequency of f2. Using the formula, we have speed = 0.487 m × f2.

Since the speed of sound in air is generally considered constant (at approximately 343 m/s at room temperature and normal atmospheric conditions), we can equate the two expressions for speed and solve for f1 and f2

0.154 m × f1 = 0.487 m × f2

By canceling out the common factor of 0.154, we get:

f1 = 0.487 m × f2 / 0.154 m

Simplifying further:

f1 ≈ 3.168 × f2

This equation implies that the frequency of the first scenario is approximately 3.168 times the frequency of the second scenario. Therefore, to determine the speed of sound under these conditions, we need more information about either the frequency in one of the scenarios or the specific speed of sound for the given conditions.

Learn more about wave here:

https://brainly.com/question/25954805

#SPJ11

Cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.

Cubic equations of state are highly useful for a wide range of compounds and applications in thermodynamics. A cubic equation derived from P vs V data (graph) of liquid and vapor is used for a variety of reasons, including: These equations make use of measurable quantities (pressure, temperature, and volume) and are extremely beneficial in the development of a thermodynamic framework for different compounds. These models may be used to estimate properties such as vapor pressures, fugacity coefficients, and liquid molar volumes, among others. The approach also allows for the calculation of the fugacity and molar volume of an ideal gas for a pure substance.

The data provided by these graphs are critical for predicting phase equilibrium in chemical engineering applications. They can also assist in the calculation of mixing and phase separation behavior for a variety of compounds. By using these equations, thermodynamic experts may evaluate the behavior of a substance and its properties under a variety of conditions, which is critical in the design and development of chemical processes. In conclusion, cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.

To know more about equations visit:

https://brainly.com/question/28956380

#SPJ11

The electric field is the area around electrically charged particles where the interaction between them creates an electric force. Electrostatics finds applications in a wide range of areas, including in the following fields:

In the industry, electrostatics is used to eliminate dirt and dust from plastic surfaces before painting them to achieve good adhesion. Aerospace engineering uses electrostatics in applications like the electrostatic cleaning of dust from the surface of spacecraft or the charging of space probes and dust detectors.

Medical technology relies on electrostatics in a range of applications, including in electrocardiography, electrophoresis, and in the use of electrostatic precipitators for respiratory protection.The electric field one-fourth of the way from a charge 4 to another charge 92 is zero.

What is the ratio of 1 to 4z?

The distance between charge 4 and charge 92 is 4z. Therefore, we can say that the electric field is zero at a distance of z from charge 4 (since z is 1/4th of the distance between 4 and 92).

Using Coulomb's law, we can calculate the electric field as:

E = (kQq)/r² Where k is the Coulomb constant, Q and q are the magnitudes of the charges, and r is the distance between them.

Since the electric field is zero at a distance of z from charge 4, we can write:

(k*4*Q)/(z²) = 0

Solving for Q, we get:

Q = 0

Therefore, the ratio of 1 to 4z is: 1/4z = 1/(4*z) = (1/4) * (1/z) = 0.25z^-1

Learn more about application of electrostatics here

https://brainly.in/question/17363791

#SPJ11

The time taken to transfer about 95% of the charge to the resistor is 65.4 s (approx)

The given values in the problem are:X = 1503 ΩZ = 15.03 mF

The time taken to transfer about 95% of its charge to the resistor can be determined using the time constant (τ) of the circuit. The time constant (τ) of the circuit is given by the formula; τ = RC

where R is the resistance of the circuit in ohms and C is the capacitance of the circuit in farads.τ = RC = (1503 Ω)(15.03 × 10⁻³ F) = 22.56849 s ≈ 22.6 s (approx)

After one time constant, the charge on the capacitor is reduced to about 36.8% of its initial charge.

Hence, to transfer about 95% of its charge to the resistor, we need to wait for about 2.9 time constants (95 ÷ 36.8 ≈ 2.9).

The time taken to transfer about 95% of the charge to the resistor is;T = 2.9τ = 2.9 × 22.56849 s = 65.43861 s ≈ 65.4 s (approx)

Therefore, the time taken to transfer about 95% of the charge to the resistor is 65.4 s (approx)

Know more about resistor here,

https://brainly.com/question/30672175

#SPJ11

The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding. Vsc (Voltmeter reading)= 250 VISc, Ammeter reading)= 7.6 APsc, (Wattmeter reading)= 440 W is the answer.

In order to determine the full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding, the given values should be utilized. The values of parameters given are: R₁ = 0.42, R₂ = 1.0, X₁ = 20, and X₂ = 0.50.

The Short circuit test is performed on the low-voltage (secondary) side of the transformer. Due to the short circuit, the secondary voltage drops to zero and hence the entire primary voltage appears across the impedance referred to as the primary. The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding can be calculated as follows:

Where Vsc= Voltmeter reading = 250

VIsc= Ammeter reading = 7.6

APsc= Wattmeter reading = 440

WZ= Impedance referred to primary side

= [tex]{{Z}_{1}}+{{Z}_{2}}[/tex]

= 0.42 + j20 + 1.0 + j0.5

= [tex]1.42 + j20.5[tex]I_{FL}[/tex]

=[tex]\frac{{{V}_{1}}}{\sqrt{3}{{Z}_{1}}}\,\,[/tex]

=[tex]\frac{500}{\sqrt{3}\left( 0.42+j20 \right)}[/tex][/tex]

= 7.06 A

The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding are as follows: 71 IFL - The primary full load current= 7.06 A72 7.3 74 Ret - The equivalent resistance, referred to as the primary side Xe1= R2= 1 Ω

The equivalent reactance, referred to as the primary side Ze1= X2= 0.5 Ω

The equivalent impedance, referred to the primary side Z = R + jX = 1 + j0.5= 1.118Ω

Vsc (Voltmeter reading)= 250 VISc (Ammeter reading)= 7.6 APsc (Wattmeter reading)= 440 W

know more about equivalent impedance,

https://brainly.com/question/31770436

#SPJ11

The car engine idling at 1200 rpm has a frequency of 20 Hz. The space-station spinning at 120 degrees per second has a frequency of approximately 0.333 Hz.

To determine the frequency in hertz, we need to convert the rotations per minute (rpm) to rotations per second. We can use the following formula:

Frequency (in hertz) = RPM / 60

For the car engine idling at 1200 rpm:

Frequency = 1200 / 60 = 20 hertz

For the space-station spinning at 120 degrees per second, we need to convert the degrees to rotations before calculating the frequency. Since one complete rotation is equal to 360 degrees, we can use the following formula:

Frequency (in hertz) = Rotations per second = Degrees per second / 360

For the space-station spinning at 120 degrees per second:

Frequency = 120 / 360 = 1/3 hertz or approximately 0.333 hertz

Therefore, the frequency of the car engine idling at 1200 rpm is 20 hertz, while the frequency of the space-station spinning at 120 degrees per second is approximately 0.333 hertz.

To know more about rotations per minute,

https://brainly.com/question/927364

#SPJ11

The average fuel burnup rate in GWd/t is 6,984.

To calculate the average fuel burnup rate in GWd/t, we need to determine the total energy generated by the reactor over the year. The formula for calculating the total energy generated is:

Total energy generated = Annual energy generation / efficiency

Given that the annual energy generation is 1,200 GW and the efficiency is 0.33, we can calculate the total energy generated as follows:

Total energy generated = 1,200 GW x 8,760 hours / 0.33 = 31,891,891 MWh

Next, we need to calculate the mass of uranium consumed by the reactor over a year. The specific energy release for enriched uranium used in a typical modern reactor is approximately 7,000 kWh/kg. Using this value, we can calculate the mass of uranium consumed as follows:

Mass of uranium consumed = Total energy generated / Specific energy release

Mass of uranium consumed = 31,891,891 MWh x 10^6 / (7,000 kWh/kg x 10^3) = 4,560 tonnes

Therefore, the mass of uranium consumed by the reactor over the year is 4,560 tonnes.

The fuel burnup rate is defined as the amount of energy produced per unit mass of fuel consumed. We can calculate the fuel burnup rate as follows:

Fuel burnup rate = Total energy generated / Mass of uranium consumed

Fuel burnup rate = 31,891,891 MWh x 10^6 / (4,560 tonnes x 10^3)

Fuel burnup rate = 6,984 GWd/t

Therefore, the average fuel burnup rate in GWd/t is 6,984.

Learn more about fuel

https://brainly.com/question/33339410

#SPJ11

By plugging in the appropriate values, you can calculate today's activity (N1) of the radioactive source. To determine today's activity (N1) of a radioactive source for which you have a calibration certificate with an original activity (N0) at a time interval (td) in the past, you can use the concept of radioactive decay and the decay constant.

The decay of a radioactive source follows an exponential decay law, which states that the activity of a radioactive sample decreases with time according to the equation:

N(t) = N0 * e^(-λt)

Where:

N(t) is the activity of the source at time t.

N0 is the original activity of the source.

λ is the decay constant.

t is the time elapsed.

The decay constant (λ) is related to the half-life (T½) of the radioactive material by the equation:

λ = ln(2) / T½

To determine today's activity (N1), you need to know the original activity (N0), the time interval (td), and the half-life of the radioactive material.

Here are the steps to calculate today's activity:

Determine the decay constant (λ) using the half-life (T½) of the radioactive material.

Calculate the time elapsed from the calibration date to today, which is td.

Use the formula N(t) = N0 * e^(-λt) to calculate N1, where N0 is the original activity and t is the time elapsed (td).

By plugging in the appropriate values, you can calculate today's activity (N1) of the radioactive source.

To know more about the radioactive source

brainly.com/question/12741761

#SPJ11

As the balloon moves closer to the conductor, the electric field strength will increase and charges will continue to be redistributed.

A) When a positively charged balloon is brought near an originally uncharged conductor, the conductor does acquire a net charge but not an equal one to that of the balloon. This is due to the fact that the conductor and balloon have different charges and therefore, when the conductor is brought near the balloon, the electrons move within the conductor leading to a net charge. When the balloon is brought near the conductor, the positively charged balloon will polarize the conductor, attracting electrons from one side and repelling them from the other side.

This will cause a net charge to be induced in the conductor due to the movement of the electrons, even if the balloon doesn't touch the conductor. This movement of electrons can result in the production of an electric current, but the amount of charge on the conductor will be less than the amount of charge on the balloon.

B) Yes, the conductor will begin to cause electric fields at points external to the conductor. This is because the positively charged balloon will cause the conductor to polarize and create an electric field in thesurrounding area.

Since the balloon and the conductor have different charges, an electric field will be induced in the area around the conductor, causing charges to be redistributed in that region. The strength of the electric field will be proportional to the magnitude of the charge on the balloon and the distance between the balloon and the conductor. Therefore, as the balloon moves closer to the conductor, the electric field strength will increase and charges will continue to be redistributed.

Learn more about Electric here,

https://brainly.com/question/776932

#SPJ11

If the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.

To calculate the cutoff frequency (Fc) of a circuit with an inductor (L) and a resistor (R), we can use the formula:

Fc = 1 / (2π√(L * R))

Given that R = 200 Ω and Fc = 3000 Hz, we can rearrange the formula to solve for L:

L = (1 / (4π² * Fc² * R))

Substituting the values:

L = (1 / (4π² * (3000 Hz)² * 200 Ω))

L ≈ 1.33 mH

Therefore, if the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.

To know more about cutoff frequency (Fc) click here:

https://brainly.com/question/15711500

#SPJ11

To derive the formula for the magnetic field at a point near an infinite and semi-infinite long wire using Biot-Savart's law.

Follow these steps:  the variables, Express Biot-Savart's law, the direction of the magnetic field,  an infinite long wire and a semi-infinite long wire.

Define the variables:

I: Current flowing through the wire

dl: Infinitesimally small length element along the wire

r: Distance between the point of interest and the current element dl

θ: Angle between the wire and the line connecting the current element to the point of interest

μ₀: Permeability of free space (constant)

Express Biot-Savart's law:

B = (μ₀ / 4π) * (I * dl × r) / r³

This formula represents the magnetic field generated by an infinitesimal current element dl at a distance r from the wire.

Determine the direction of the magnetic field:

The magnetic field is perpendicular to both dl and r, and follows the right-hand rule. It forms concentric circles around the wire.

Consider an infinite long wire:

In the case of an infinite long wire, the wire extends infinitely in both directions. The current is assumed to be uniform throughout the wire.

The contribution to the magnetic field from different segments of the wire cancels out, except for those elements located at the same distance from the point of interest.

By symmetry, the magnitude of the magnetic field at a point near an infinite long wire is given by:

B = (μ₀ * I) / (2π * r)

This formula represents the magnetic field at a point near an infinite long wire.

Consider a semi-infinite long wire:

In the case of a semi-infinite long wire, we have one end of the wire located at the point of interest, and the wire extends infinitely in one direction.

The contribution to the magnetic field from segments of the wire located beyond the point of interest does not affect the field at the point of interest.

By considering only the current elements along the finite portion of the wire, we can derive the formula for the magnetic field at a point near a semi-infinite long wire.

The magnitude of the magnetic field at a point near a semi-infinite long wire is given by:

B = (μ₀ * I) / (2π * r)

This formula is the same as that for an infinite long wire.

By following these steps, we can derive the formula for the magnetic field at a point near an infinite and semi-infinite long wire using Biot-Savart's law.

To know more about Biot-Savart's law

https://brainly.com/question/1120482

#SPJ11

The question requires the calculation of the Earth's average temperature in °C if the earth had no atmosphere given the following information.

Sun's intensity at the distance of the earth is 1370 W/m².

30% of this energy is reflected by water and clouds;

70% is absorbed.

The emissivity of the surface is very close to 1. The actual average temperature of the earth, about 15 °C, is higher than the calculation because of the greenhouse effect.

Calculation of Earth's temperature:

The formula to determine the temperature is given by P = e σ A T⁴. Here,

P is the power received by the Earth from the Sun.

A is the surface area of the Earth,

T is the temperature in kelvin,

e is the emissivity of the surface,

σ is the Stefan-Boltzmann constant, and the remaining terms have the usual meanings.

Substituting the values in the formula,

P = (1 - 0.30) × 1370 W/m² × 4π (6,371 km)²

= 9.04 × 10¹⁴ Wσ

= 5.67 × 10⁻⁸ W/m² K⁴A

= 4π (6,371 km)²

= 5.10 × 10¹⁴ m²e = 1

Hence, the formula now becomes

9.04 × 10¹⁴ = 1 × 5.67 × 10⁻⁸ × 5.10 × 10¹⁴ × T⁴

⇒ T⁴ = 2.0019 × 10⁴

⇒ T = 231.02

K= -42.13°C

Answer: The Earth's average temperature would be -42.13°C.

Learn more about green house effect here

https://brainly.com/question/17023405

#SPJ11

The pressure inside the 32.0 L container holding 104.1 kg of argon gas at 20.3°C is approximately 67279.93 Pa.

To calculate the pressure inside a container of gas, we can use the ideal gas law equation:

PV = nRT

Where:

P is the pressure of the gas

V is the volume of the container

n is the number of moles of gas

R is the ideal gas constant (8.314 J/(mol·K))

T is the temperature in Kelvin

First, let's convert the given temperature from Celsius to Kelvin:

T = 20.3°C + 273.15 = 293.45 K

Next, we need to determine the number of moles of argon gas using the molar mass of argon (Ar), which is approximately 39.95 g/mol.

n = mass / molar mass

n = 104.1 kg / (39.95 g/mol * 0.001 kg/g)

n = 2604.006 moles

Now, we can substitute the values into the ideal gas law equation to solve for the pressure:

P * 32.0 L = (2604.006 mol) * (8.314 J/(mol·K)) * 293.45 K

P = (2604.006 * 8.314 * 293.45) / 32.0

P ≈ 67279.93 Pa

To know more about ideal gas law

https://brainly.com/question/30458409

#SPJ11

The wavelength of the light is 267 nm, the position of the third order bright fringe is approximately 0.76 degrees, the angle of the first order dark fringe for red light is approximately 0.333 degrees, the slit width is approximately 0.060 m and the width of the central diffraction peak for violet light is approximately 3.8 cm.

To find the wavelength of light, we can use the formula for the position of the bright fringe in a double-slit interference pattern:

y = (m * λ * L) / d

where:

y is the distance of the bright fringe from the center line,

m is the order of the bright fringe (1 for the first order),

λ is the wavelength of light,

L is the distance from the slits to the observing screen,

d is the separation between the two slits.

Given that y = 4.0 mm = 0.004 m, m = 1, L = 3.0 m, and d = 0.20 mm = 0.0002 m, we can solve for λ:

0.004 = (1 * λ * 3.0) / 0.0002

λ = (0.004 * 0.0002) / 3.0 = 2.67 × 1[tex]10^{-7}[/tex] m = 267 nm

Therefore, the wavelength of the light is 267 nm.

To find the position of the third order bright fringe, we can use the same formula with m = 3:

y = (3 * λ * L) / d

Substituting the given values, we have:

y = (3 * 267 * [tex]10^{-9}[/tex] * 3.0) / 0.0002 = 0.040 m

To convert this to degrees, we can use the formula:

θ = arctan(y / L)

θ = arctan(0.040 / 3.0) ≈ 0.76 degrees

Therefore, the position of the third order bright fringe is approximately 0.76 degrees.

For the single-slit diffraction pattern, the formula for the angle of the dark fringe can be expressed as:

θ = λ / (2 * w)

where:

θ is the angle of the dark fringe,

λ is the wavelength of light,

w is the slit width.

Given that λ = 700.0 nm = 7.00 × [tex]10^{-7}[/tex] m and the central diffraction peak width is 6.00 cm = 0.06 m, we can solve for θ:

θ = (7.00 × [tex]10^{-7}[/tex]) / (2 * 0.06) ≈ 0.0058 radians

To convert this to degrees, we multiply by 180/π:

θ ≈ 0.0058 * (180/π) ≈ 0.333 degrees

Therefore, the angle of the first order dark fringe for red light is approximately 0.333 degrees.

To find the slit width w, we rearrange the formula:

w = λ / (2 * θ)

Substituting the given values, we have:

w = (7.00 × [tex]10^{-7}[/tex]) / (2 * 0.0058) ≈ 0.060 m

Therefore, the slit width is approximately 0.060 m.

Finally, to find the width of the central diffraction peak for violet light of wavelength 440.0 nm = 4.40 × [tex]10^{-7}[/tex] m, we can use the same formula:

w = λ / (2 * θ)

Substituting λ = 4.40 × [tex]10^{-7}[/tex] m and θ = 0.0058 radians, we have:

w = (4.40 × [tex]10^{-7}[/tex]) / (2 * 0.0058) ≈ 0.038 m = 3.8 cm

Therefore, the width of the central diffraction peak for violet light is approximately 3.8 cm.

Learn more about diffraction here:

https://brainly.com/question/12290582

#SPJ11

(a) It takes approximately 8.3 minutes for a photon to travel from the Sun to the Earth.

(b) A photon with a wavelength of 513 nm has an energy of approximately 2.42 eV.

(c) A photon with an energy of 1.58 eV has a wavelength of approximately 7.83 × 10^-7 meters.

(a) Calculation of the time it takes a photon to travel from the Sun to the Earth:

The average distance from the Sun to the Earth is approximately 93 million miles or 150 million kilometers. Convert this distance to meters by multiplying it by 1,000, as there are 1,000 meters in a kilometer. So, the distance is 150,000,000,000 meters.

The speed of light in a vacuum is approximately 299,792 kilometers per second or 299,792,458 meters per second. To find the time it takes for a photon to travel from the Sun to the Earth, divide the distance by the speed of light:

Time = Distance / Speed of Light

Time = 150,000,000,000 meters / 299,792,458 meters per second

This gives  approximately 499.004 seconds. To convert this to minutes, we divide by 60:

Time in minutes = 499.004 seconds / 60 = 8.3167 minutes

Therefore, it takes approximately 8.3 minutes for a photon to travel from the Sun to the Earth.

(b) Calculation of the energy of a photon with a wavelength of 513 nm:

The energy of a photon can be calculated using the equation E = hc/λ, where E is the energy, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon.

Planck's constant (h) is approximately 4.1357 × 10^-15 eV·s.

The speed of light (c) is approximately 299,792,458 meters per second.

The given wavelength is 513 nm, which can be converted to meters by multiplying by 10^-9 since there are 1 billion nanometers in a meter. So, the wavelength is 513 × 10^-9 meters.

Substituting the values into the equation,

E = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / (513 × 10^-9 m)

Simplifying the equation, we get:

E = (1.2457 × 10^-6 eV·m) / (513 × 10^-9 m)

By dividing the numerator by the denominator,

E ≈ 2.42 eV

Therefore, a photon with a wavelength of 513 nm has an energy of approximately 2.42 eV.

(c) Calculation of the wavelength of a photon with an energy of 1.58 eV:

To find the wavelength of a photon given its energy, we rearrange the equation E = hc/λ to solve for λ.

We have the given energy as 1.58 eV.

Substituting the values into the equation,

1.58 eV = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / λ

To isolate λ, we rearrange the equation:

λ = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / 1.58 eV

By dividing the numerator by the denominator,

λ ≈ 7.83 × 10^-7 meters

Therefore, a photon with an energy of 1.58 eV has a wavelength of approximately 7.83 × 10^-7 meters or 783 nm.

These calculations assume that the photons are traveling in a vacuum.

Learn more about photon here:

https://brainly.com/question/33017722

#SPJ11

The net momentum of the system before the collision is given by the expression: Momentum before = m1v1 + m2v2where m1 and v1 are the mass and velocity of the cue ball respectively and m2 and v2 are the mass and velocity of the eight ball respectively.

Substituting in the given values, we have:Momentum before = (0.6 kg) (3.0 m/s) + (0.55 kg) (2.0 m/s) = 1.80 kg m/s + 1.10 kg m/s = 2.90 kg m/s. The net momentum of the system after the collision is given by the expression:Momentum after = m1v1' + m2v2'where v1' and v2' are the velocities of the cue ball and eight ball respectively after the collision.

Substituting in the given values, we have: Momentum after = (0.6 kg) (2.0 m/s cos 40°) + (0.55 kg) (v2')Momentum after = 1.20 cos 40° kg m/s + (0.55 kg) (v2')Momentum after = 0.92 kg m/s + 0.55 kg v2'Conservation of momentum principle states that the total momentum before the collision must equal the total momentum after the collision: Momentum before = Momentum after2.90 kg m/s = 0.92 kg m/s + 0.55 kg v2'Solving for v2', we get:v2' = (2.90 kg m/s - 0.92 kg m/s) / 0.55 kgv2' = 4.71 m/s.

The north component (y-component) of the momentum of the cue ball after collision is given by the expression:py = m1v1' sin θSubstituting the given values, we have:py = (0.6 kg) (2.0 m/s sin 40°)py = 0.78 kg m/sTherefore, the final velocity of the eight ball is 4.71 m/s.

Learn more on momentum here:

brainly.in/question/7381860

#SPJ11