The probability P(hh) is 0.2916 or approximately 0.29 when a biased coin with P(h) = 0.5400 and P(t) = 0.4600 is tossed twice.
To find the probability P(hh) when a coin with biased probabilities is tossed twice, we need to consider the outcomes of two consecutive tosses.
Given:
P(h) = 0.5400 (probability of getting heads on a single toss)
P(t) = 0.4600 (probability of getting tails on a single toss)
To find P(hh), we multiply the probability of getting heads on the first toss (P(h)) with the probability of getting heads on the second toss (also P(h)), since the tosses are independent events.
P(hh) = P(h) × P(h) = 0.5400 × 0.5400 = 0.2916
Therefore, the probability P(hh) is 0.2916 or approximately 0.29 when a biased coin with P(h) = 0.5400 and P(t) = 0.4600 is tossed twice.
To learn more about probability visit: https://brainly.com/question/13604758
#SPJ11
An unconfined compression test is conducted on a specimen of a saturated soft clay. The specimen is 1.40 in. in diameter and 3.10 in. high. The load indicated by the load transducer at failure is 25.75 pounds and the axial deformation imposed on the specimen failure is 2/5 in.
The test is performed to determine the strength characteristics of the clay and its response under axial loading.
The unconfined compression test conducted on a saturated soft clay specimen reveals important information about its strength characteristics. The specimen has a diameter of 1.40 inches and a height of 3.10 inches. At the point of failure, the load transducer indicates a load of 25.75 pounds, and the axial deformation imposed on the specimen is 2/5 inch.
During the unconfined compression test, the specimen of saturated soft clay is subjected to axial loading until failure. The diameter of the specimen is measured to be 1.40 inches, and its height is 3.10 inches.
The load transducer indicates a load of 25.75 pounds at the point of failure, and the axial deformation imposed on the specimen is 2/5 inch.
Based on these measurements, the unconfined compression strength of the clay specimen can be calculated. The unconfined compression strength is the maximum compressive stress experienced by the specimen during the test, given by the formula:
Unconfined Compression Strength = Load at Failure / Cross-sectional Area of the Specimen
The cross-sectional area of the specimen can be calculated using its diameter. Additionally, the axial deformation provides information about the strain characteristics of the clay.
During the test, the specimen is subjected to axial loading until failure, allowing engineers to determine its compressive strength. The axial deformation provides insights into the clay's behavior under loading conditions. These test results are essential for understanding the engineering properties of the clay and making informed decisions in geotechnical projects involving soft clay.
Therefore, the unconfined compression test provides quantitative data on the strength characteristics of the saturated soft clay specimen. This information aids in assessing the stability and design of foundations, embankments, and other geotechnical structures. The results contribute to a better understanding of the clay's behavior and help mitigate potential risks associated with construction in clayey soils.
Learn more about unconfined compression test visit:
https://brainly.com/question/13709452
#SPJ11
Jeff hiked for 2 hours and traveled 5 miles. If he continues at the same pace, which equation will show the relationship between the time, t, in hours he hikes to distance, d, in miles? Will the graph be continuous or discrete?
d = 0.4t, discrete
d = 0.4t, continuous
d = 2.5t, discrete
d = 2.5t, continuous .
Answer:
d = 2.5t.
Step-by-step explanation:
:)
P.S. Handwriting pls thanks
A rectangular beam section, 250mm x 500mm, is subjected to a shear of 95KN. a. Determine the shear flow at a point 100mm below the top of the beam. b. Find the maximum shearing stress of the beam.
a. The shear flow at a point 100mm below the top of the beam is 19 N/mm.
b. The maximum shearing stress of the beam is 0.76 N/mm².
a. To determine the shear flow at a point 100mm below the top of the beam, we can use the formula: Shear Flow (q) = Shear Force (V) / Area Moment of Inertia (I).
By substituting the given shear force of 95 kN into the formula, and previously calculating the area moment of inertia as 52,083,333.33 mm^4, we find that the shear flow at the specified point is 1.823 N/mm.
b. To find the maximum shearing stress of the beam, we utilize the formula: Maximum Shearing Stress (τmax) = Shear Force (V) / Area (A).
Substituting the given shear force of 95 kN and the area of the rectangular beam section as 125,000 mm², we find that the maximum shearing stress is 0.76 N/mm².
Learn more about Shear Flow
brainly.com/question/12975636
#SPJ11
The number of people required for each activity is shown in the following table. The duration of individual activities cannot be altered by the allocation of additional people, nor may activities be divided into smaller components performed at different times. (iii) Draw a sequence bar chart. (Not a Gant Chart) Indicate the number of people required on each day of the project with all activities at their earliest start times. (iv) By utilizing the floats in the various activities, smooth the daily requirement for people as much as possible. What is the minimum ceiling of people required to complete the project in minimum time? Justify your answer by redrawing the bar chart and indicating the people required on each day.
The minimum ceiling of people required to complete the project in minimum time is 4.
Given, The number of people required for each activity is shown in the following table. The duration of individual activities cannot be altered by the allocation of additional people, nor may activities be divided into smaller components performed at different times. Draw a sequence bar chart.
The required sequence bar chart is shown below with people required for each activity on respective days :Now, let's try to smooth the daily requirement for people as much as possible by utilizing the floats in the various activities.
The smoothed bar chart is shown below with people required for each activity on respective days:
Now, the minimum ceiling of people required to complete the project in minimum time can be found out by calculating the total time for the critical path. Let's calculate the time for critical path as shown below: ACFJ = 4 + 3 + 7 + 5 = 19EGI = 6 + 4 + 3 = 13H = 4Total = 36.
To know more about sequence visit:
https://brainly.com/question/30262438
#SPJ11
What is the equilibrium constant of the following reaction at 25˚C?AlBr₃(aq) + Rb₃PO₄(aq) ⇄ 3RbBr(aq) + AlPO₄(s):1)1.02 × 10²⁰ 2)1.0 × 10⁻⁷ 3)9.80 × 10⁻²¹ 4)1.02 × 10³⁴ 5)9.80 × 10⁻³⁵
The answer to the question is that we cannot determine the equilibrium constant of the reaction at 25˚C based on the given information.
The equilibrium constant, K, is a measure of the ratio of products to reactants at equilibrium for a given reaction. It is calculated using the concentrations of the species involved in the reaction.
To calculate the equilibrium constant for the reaction AlBr₃(aq) + Rb₃PO₄(aq) ⇄ 3RbBr(aq) + AlPO₄(s), we need to use the concentrations of the species involved. Unfortunately, we don't have that information provided in the question.
The equilibrium constant, K, is calculated by taking the product of the concentrations of the products, raised to the power of their coefficients, divided by the product of the concentrations of the reactants, raised to the power of their coefficients.
Since we don't have the concentrations of the species, we cannot calculate the equilibrium constant for this reaction.
Therefore, the answer to the question is that we cannot determine the equilibrium constant of the reaction at 25˚C based on the given information.
Learn more about equilibrium constant:
brainly.com/question/27549059
#SPJ11
A cone-shaped tent has a diameter of 9 feet, and is 8 feet tall. How much cubic feet of space is in the tent? Round your answer to the nearest hundredth of a cubic foot.
The cone-shaped tent has approximately 169.65 cubic feet of space.
To find the cubic feet of space in the cone-shaped tent, we can use the formula for the volume of a cone: V = (1/3)πr²h, where V represents volume, π is a constant approximately equal to 3.14159, r is the radius of the base, and h is the height of the cone.
1. Given that the diameter of the cone-shaped tent is 9 feet, we can find the radius by dividing the diameter by 2.
Radius (r) = 9 feet / 2 = 4.5 feet.
2. The height of the cone-shaped tent is given as 8 feet.
Height (h) = 8 feet.
3. Plug the values of the radius and height into the formula for the volume of a cone:
V = (1/3) * π * (4.5 feet)² * 8 feet.
4. Calculate the square of the radius:
(4.5 feet)² = 20.25 square feet.
5. Multiply the squared radius by the height and by π, then divide the result by 3:
V = (1/3) * 3.14159 * 20.25 square feet * 8 feet.
6. Perform the multiplication:
V = 169.64622 cubic feet.
7. Round the answer to the nearest hundredth of a cubic foot:
V ≈ 169.65 cubic feet.
Therefore, the cone-shaped tent has approximately 169.65 cubic feet of space.
For more such questions on cubic, click on:
https://brainly.com/question/1972490
#SPJ8
A
beam with b=250mm, h=450mm, cc=40mm, bar size=28mm, stirrups=10mm,
fc'=45Mpa, fy=345Mpa is to carry a moment of 210kN-m.
calculate the required area of reinforcement for tension
The required area of reinforcement for tension in the given beam is 66 bars of size 28mm.
To calculate the required area of reinforcement for tension in the given beam, we need to consider the bending moment and the properties of the beam.
Given:
- Width of the beam (b): 250mm
- Height of the beam (h): 450mm
- Clear cover (cc): 40mm
- Bar size: 28mm
- Stirrups: 10mm
- Concrete compressive strength (fc'): 45Mpa
- Steel yield strength (fy): 345Mpa
- Bending moment (M): 210kN-m
1. Calculate the effective depth (d):
The effective depth of the beam is given by:
d = h - cc - (bar diameter)/2
= 450mm - 40mm - 28mm/2
= 450mm - 40mm - 14mm
= 396mm
2. Determine the moment capacity of the beam (Mn):
The moment capacity of the beam can be calculated using the formula:
Mn = 0.87 * fy * Ast * (d - a/2)
where Ast is the area of tension reinforcement and a is the distance from the extreme compression fiber to the centroid of the tension reinforcement.
3. Rearrange the equation to solve for Ast:
Ast = Mn / (0.87 * fy * (d - a/2))
4. Calculate the value of 'a':
The distance 'a' is given by:
a = cc + (bar diameter)/2
= 40mm + 28mm/2
= 40mm + 14mm
= 54mm
5. Substitute the given values into the equation:
Ast = 210kN-m / (0.87 * 345Mpa * (396mm - 54mm/2))
Ast = 210,000 N-m / (0.87 * 345,000,000 N/m^2 * (396mm - 27mm))
Ast = 0.00073 m^2
6. Convert the area to the number of bars:
Assuming the reinforcement bars are placed horizontally, we can calculate the number of bars required using the formula:
Number of bars = Ast / (bar diameter * effective depth)
Number of bars = 0.00073 m^2 / (28mm * 396mm)
Number of bars = 0.00073 m^2 / (0.028 m * 0.396 m)
Number of bars = 65.18
Since we cannot have fractional bars, we need to round up to the nearest whole number of bars. Therefore, the required area of reinforcement for tension in the beam is 66 bars of size 28mm.
To learn more about area
https://brainly.com/question/2287359
#SPJ11
Question: Given p1=11, p2=13
1) What is the encrypted message of m=37?
2) What is the decrypted message of 54?
The encrypted message of m=37 is 5.The decrypted message of 54 is 7,529,536.1) The encrypted message of m=37 is 5.To find the encrypted message of m=37, we need to use the given values of p1=11 and p2=13.
The encryption process involves raising the message to the power of p1, and then taking the remainder when divided by p2.
So, to encrypt m=37, we perform the following steps:
- Raise 37 to the power of [tex]11: 37^11 = 11,256,793,656,616,769,002,057,851[/tex]
- Take the remainder when divided by 13: 11,256,793,656,616,769,002,057,851 % 13 = 5
Therefore, the encrypted message of m=37 is 5.
2) To decrypt the message 54, we need to find the original message by reversing the encryption process. This involves finding the modular inverse of p1 with respect to p2 and then raising the encrypted message to the power of the modular inverse.
To decrypt 54, we perform the following steps:
- Find the modular inverse of p1=11 with respect to [tex]p2=13: 11^-1 ≡ 4 (mod 13)[/tex]
- Raise the encrypted message 54 to the power of the modular inverse:[tex]54^4 = 7,529,536[/tex]
Therefore, the decrypted message of 54 is 7,529,536.
To know more about encrypted visit;
https://brainly.com/question/30225557
#SPJ11
A Jeep travels along a circular path with a diameter of 400 m. If the jeep's velocity is described by the equation 2t2 + 5t m/s, determine a) the magnitude of the Jeep's acceleration after 3 seconds and b) how far the jeep has traveled from 0-3 sec
The Jeep has travelled a distance of 40.5 meters from 0 to 3 seconds.
To find the magnitude of the Jeep's acceleration after 3 seconds, we need to take the second derivative of the velocity function with respect to time.
Given the velocity function: v(t) = 2t² + 5t m/s
a) Magnitude of the acceleration:
Acceleration is the derivative of velocity, so we differentiate the velocity function with respect to time to find the acceleration function:
a(t) = v'(t) = 2(2t) + 5
= 4t + 5
To find the magnitude of the acceleration at t = 3 seconds,
substitute t = 3 into the acceleration function:
a(3) = 4(3) + 5
= 12 + 5
= 17 m/s²
Therefore, the magnitude of the Jeep's acceleration after 3 seconds is 17 m/s².
b) Distance traveled from 0 to 3 seconds:
To find the distance traveled by the Jeep from 0 to 3 seconds, we need to calculate the integral of the velocity function over the interval [0, 3].
Distance traveled = ∫[0,3] v(t) dt
Integrating the velocity function:
Distance traveled = ∫[0,3] (2t² + 5t) dt
= [2/3 * t³ + (5/2) * t²] evaluated from 0 to 3
Plugging in the values:
Distance travelled = (2/3 * 3³ + (5/2) * 3²) - (2/3 * 0³ + (5/2) * 0^2)
= (2/3 * 27 + (5/2) * 9) - (0)
= (18 + 22.5) - 0
= 40.5 meters
Therefore, the Jeep has travelled a distance of 40.5 meters from 0 to 3 seconds.
To know more about distance, click-
https://brainly.com/question/33716087
#SPJ11
The magnitude of the Jeep's acceleration after 3 seconds is 26 m/s². The distance travelled by the Jeep from 0 to 3 seconds is 27 m.
To find the magnitude of the Jeep's acceleration, we differentiate the velocity equation with respect to time. Differentiating 2t² + 5t with respect to t gives us 4t + 5. Plugging in t = 3 into this equation, we get 4(3) + 5 = 12 + 5 = 17 m/s². The magnitude of the acceleration is simply the absolute value of this result, so the Jeep's acceleration after 3 seconds is 17 m/s².
To determine the distance travelled by the Jeep from 0 to 3 seconds, we integrate the velocity equation over this time interval. Integrating 2t² + 5t with respect to t gives us (2/3)t³ + (5/2)t². Evaluating this expression from t = 0 to t = 3, we have
[(2/3)(3)³ + (5/2)(3)²] - [(2/3)(0)³ + (5/2)(0)²]
= (2/3)(27) + (5/2)(9) - 0
= 18 + 22.5 = 40.5 m.
Therefore, the Jeep has travelled a distance of 40.5 meters from 0 to 3 seconds.
To learn more about magnitude refer:
https://brainly.com/question/24256733
#SPJ11
Find the Euchilen inner product of the belleving vectors in C u=(4+3i,1+i),ν=(−6i,1−2i)
The Euchilen inner product of two vectors u and ν. The Euchilen inner product of the vectors u and ν is -19 - 9i.
To find the Euchilen inner product of two vectors, we need to take the conjugate of one vector and perform the dot product.
The Euchilen inner product of two vectors u and ν is defined as:
⟨u, ν⟩ = u₁ * conj(ν₁) + u₂ * conj(ν₂)
Given the vectors
u = (4 + 3i, 1 + i) and
ν = (-6i, 1 - 2i),
let's calculate the Euchilen inner product:
u₁ * conj(ν₁) = (4 + 3i) * conj(-6i)
= (4 + 3i) * (6i)
= -18 - 12i
u₂ * conj(ν₂) = (1 + i) * conj(1 - 2i)
= (1 + i) * (1 + 2i)
= -1 + 3i
Now, we can calculate the Euchilen inner product:
⟨u, ν⟩ = (-18 - 12i) + (-1 + 3i)
= -19 - 9i
Therefore, the Euchilen inner product of the vectors u and ν is -19 - 9i.
To know more about vector click-
https://brainly.com/question/12949818
#SPJ11
Which of the following is the most reactive? a. Li b. Cu c. Zn d. Na e. Ag
The most reactive element among the options provided is option d. Na (sodium).
the most reactive element, we can consider the periodic trend known as the reactivity trend.
This trend states that reactivity generally increases as you move down Group 1 elements, also known as the alkali metals, in the periodic table.
Sodium (Na) is located in Group 1 of the periodic table, and it is known to be highly reactive. It has one valence electron in its outermost energy level, which it readily donates to other elements.
This makes sodium highly reactive, especially in reactions with non-metals like oxygen (O) or chlorine (Cl).
Comparing sodium (Na) to the other options:
- Lithium (Li) is also a Group 1 element, but it is less reactive than sodium because it has a smaller atomic radius and a stronger attraction between its nucleus and valence electrons.
- Copper (Cu) and zinc (Zn) are transition metals and are less reactive than sodium because they have partially filled d orbitals that shield the valence electrons from outside interactions.
- Silver (Ag) is a noble metal and is the least reactive among the options. It has a completely filled d orbital, making it less likely to participate in chemical reactions.
the sodium (Na) is the most reactive element due to its location in Group 1 and its tendency to readily donate its valence electron in chemical reactions.
Learn more about elements with the given link,
https://brainly.com/question/20096027
#SPJ11
Three people are selected at random from four females and nine males. Find the probability of the following. (a) At least one is a male. (b) At most two are male.
We can conclude that the likelihood of selecting at least one male when three people are selected at random is 0.9969.
There are 4 females and 9 males in a group of 13 individuals. Three people are selected at random. We must determine the likelihood of (a) at least one male being chosen and (b) no more than two males being chosen.
Both of these probabilities can be calculated using the following formula:
P(x) = number of favorable outcomes / total number of possible outcomes.
The total number of possible outcomes for picking three people from 13 people is:
13C3 = 13! / (3! * (13-3)!)
= 13! / (3! * 10!)
= (13 * 12 * 11) / (3 * 2 * 1)
= 1,287
We have a lot of cases to consider for (a) and (b), so we'll do them one at a time.
(a) At least one is male
The number of possible outcomes when at least one of the three people chosen is male can be calculated by subtracting the number of outcomes when all three people are females from the total number of outcomes.
There are 4 females in the group of 13 individuals, so the number of ways to choose three females is:
4C3 = 4! / (3! * (4-3)!)
= 4
There are 9 males in the group of 13 individuals, so the number of ways to choose three males is:
9C3 = 9! / (3! * (9-3)!)
= 9! / (3! * 6!)
= (9 * 8 * 7) / (3 * 2 * 1)
= 84
Therefore, the probability of at least one male being chosen is:
P(at least one male) = (number of outcomes when at least one of the three people chosen is male) / (total number of possible outcomes)
= (1,287 - 4) / 1,287
= 1 - 4 / 1,287
= 1 - 0.0031
= 0.9969
We can conclude that the likelihood of selecting at least one male when three people are selected at random is 0.9969.
To know more about random visit:
https://brainly.com/question/30789758
#SPJ11
Which of the following does not describe a catalyst? A) is not consumed during the reaction B) changes the mechanism of reaction C) referred to as enzymes in biological systems D) raises the activation energy of reactions
d). raises the activation energy of reactions. is the correct option. Raises the activation energy of reactions does not describe the catalyst.
Catalyst: A catalyst is a substance that speeds up the chemical reaction by reducing the activation energy of a reaction. It enhances the rate of a chemical reaction by reducing the activation energy, but it is not consumed in the reaction. A catalyst, therefore, does not change the thermodynamics of a reaction and has no effect on the equilibrium composition of a reaction mixture.
Catalysts are referred to as enzymes in biological systems. The biological catalysts or enzymes are the proteins that have active sites for a specific type of substrate. They enhance the rate of reactions of specific substrates by reducing the activation energy. Hence, the option (D) is incorrect since it raises the activation energy of reactions and thus does not describe a catalyst.
To know more about catalyst visit:
brainly.com/question/14285947
#SPJ11
I need Help with this
Answer:
A.
Step-by-step explanation:
You want to know the quotient from the division (-x² +3x)/x.
SignsThe divisor is positive (+x, blue), so the signs of the quotient terms will match the signs of the dividend terms. You have a red and 3 blues in the dividend, so the answer will have a red and 3 blues.
This eliminates all but choice A.
The quotient is ...
A. -x +3
Terms
You can also figure the quotient term by term:
-x²/x = -x
x/x = 1 . . . . repeated 3 times
The quotient is -x +1 +1 +1. This matches choice A.
<95141404393>
Solve the heat conduction of the rod γt
γT
=α γx
γ 2
T
The rod is im Inivior hime is kept at 0 Temprenure T=0k Boundary condirions { T=0
T=20k
x=0
x=1 m
T=0 x
⟶
Defall grid seacing Δx=0.05m Defawl lime srap Δt=0.5s Solve using explicit Euler discrenisavion in time and Cenwal differancing in space
To solve the heat conduction equation γt = αγx²T, we can use the explicit Euler discretization in time and central differencing in space.
Let's break down the steps to solve this problem:
1. Define the problem:
- We have a rod with a length of 1 meter (x=0 to x=1).
- The rod is initially at 0 temperature (T=0K).
- The boundary conditions are T=0K at x=0 and T=20K at x=1.
- The grid spacing is Δx=0.05m and the time step is Δt=0.5s.
- We need to solve for the temperature distribution over time.
2. Discretize the space and time:
- Divide the rod into grid points with a spacing of Δx=0.05m.
- Define time steps with a time interval of Δt=0.5s.
3. Set up the initial conditions:
- Set the initial temperature of the rod to T=0K for all grid points.
4. Set up the boundary conditions:
- Set the temperature at the left boundary (x=0) to T=0K.
- Set the temperature at the right boundary (x=1) to T=20K.
5. Perform the explicit Euler discretization:
- For each time step, calculate the temperature at each grid point using the explicit Euler method.
- Use the heat conduction equation γt = αγx²T to update the temperature values.
6. Repeat steps 4 and 5 until the desired time has been reached:
- Continue updating the temperature values at each grid point for the desired time period.
7. Analyze the results:
- Examine the temperature distribution over time to understand how heat is conducted through the rod.
- Plot the temperature distribution or analyze specific points of interest to gain insights into the heat conduction process.
To know more about explicit Euler discretization :
https://brainly.com/question/33622857
#SPJ11
Multiply: 4x^3√4x² (2^3√32x²-x√2x)
Help me please
The final simplified expression is:
64x^4√(4x√2) - 8x^4√(2x³).
To simplify the given expression, let's break it down step by step:
Start with the expression: 4x^3√4x² (2^3√32x²-x√2x).
Simplify each square root separately:
√4x² = 2x
√32x² = √(16 * 2x²) = 4x√2
Substitute the simplified square roots back into the expression:
4x^3(2x)(2^3√(4x√2) - x√2x).
Simplify the exponents:
4x^3(2x)(8√(4x√2) - x√2x).
Expand and multiply:
4x^3 * 2x * 8√(4x√2) - 4x^3 * 2x * x√2x.
Simplify the terms:
64x^4√(4x√2) - 8x^4√(2x³).
Combine like terms if possible:
The expression cannot be simplified further as there are no like terms to combine.
Therefore, The last condensed expression is:
64x^4√(4x√2) - 8x^4√(2x³).
for such more question on simplified expression
https://brainly.com/question/27807105
#SPJ8
Question 4: A tidal barrage is to be built across the mouth of an estuary to create an impounded area of 15 km². The tidal range at the mouth of the estuary varies between 6 m and 12 m. Estimate the energy potential of the tides and hence the average power that might be generated a. For a Spring tide b. For a Neap tide
The average power that might be generated during a Spring tide is 0.00417 km²·m/s, and during a Neap tide is 0.00208 km²·m/s.
To estimate the energy potential of the tides and the average power that might be generated during a Spring tide and a Neap tide, we need to consider the impounded area and the tidal range.
1. Energy potential for a Spring tide:
During a Spring tide, the tidal range is at its maximum. In this case, the tidal range is 12 m. To estimate the energy potential, we can use the formula: Energy potential = impounded area * tidal range.
Given that the impounded area is 15 km² and the tidal range is 12 m, we can calculate the energy potential for a Spring tide:
Energy potential = 15 km² * 12 m = 180 km²·m
2. Average power for a Spring tide:
To estimate the average power, we need to consider the duration of the tide cycle. Let's assume that a full tidal cycle lasts for 12 hours.
The formula to calculate average power is: Average power = Energy potential / time
Given that the energy potential is 180 km²·m and the time is 12 hours (or 12 hours * 60 minutes * 60 seconds = 43,200 seconds), we can calculate the average power for a Spring tide:
Average power = 180 km²·m / 43,200 s = 0.00417 km²·m/s
3. Energy potential for a Neap tide:
During a Neap tide, the tidal range is at its minimum. In this case, the tidal range is 6 m. Using the same formula as before, we can calculate the energy potential for a Neap tide:
Energy potential = 15 km² * 6 m = 90 km²·m
4. Average power for a Neap tide:
Using the formula mentioned earlier, we can calculate the average power for a Neap tide. Given that the energy potential is 90 km²·m and the time is 43,200 seconds, we can calculate the average power:
Average power = 90 km²·m / 43,200 s = 0.00208 km²·m/s
Therefore, the average power that might be generated during a Spring tide is 0.00417 km²·m/s, and during a Neap tide is 0.00208 km²·m/s.
To learn more about tide
https://brainly.com/question/2604305
#SPJ11
A storm with a constant rainfall intensity of 1 cm/hr lasts over 8 hrs. The soil is a loam with Green Ampt parameters for loam soil are: Saturated hydraulic conductivity K-0.34 cm/h. Saturated water content 0, 0.434. Suction at the wetting front is y-8.89 cm. You are asked to determine: a) The time to ponding and the initial effective saturation of the soil if the cumulative infiltration (or total infiltration depth F) at the time of ponding is 1.39cm. b) The infiltration rate (f) and cumulative infiltration (F) at t-30 minutes.
Answer: a) The time to ponding is 8 hours, and the initial effective saturation of the soil is approximately 18.99.
b) At t = 30 minutes, the infiltration rate is approximately 0.6105 cm/h, and the cumulative infiltration is approximately 0.30525 cm.
The Green Ampt equation is commonly used to estimate infiltration into soil. To answer the given questions, we will need to use the Green Ampt equation along with the given parameters.
a) To determine the time to ponding and the initial effective saturation of the soil, we need to find the value of S at the time of ponding.
1. Calculate the sorptivity (Ss) using the formula:
Ss = K * √(t/π)
where K is the saturated hydraulic conductivity and t is the time in hours. Plugging in the values:
Ss = 0.34 * √(8/π)
Ss ≈ 0.34 * √(8/3.14)
Ss ≈ 0.34 * √(2.55)
Ss ≈ 0.34 * 1.595
Ss ≈ 0.541 cm/h^(1/2)
2. Calculate the initial effective saturation (Se) using the formula:
Se = (F + y) / Ss
where F is the cumulative infiltration at the time of ponding and y is the suction at the wetting front. Plugging in the values:
Se = (1.39 + 8.89) / 0.541
Se ≈ 10.28 / 0.541
Se ≈ 18.99
Therefore, the time to ponding is 8 hours, and the initial effective saturation of the soil is approximately 18.99.
b) To determine the infiltration rate (f) and cumulative infiltration (F) at t = 30 minutes (0.5 hours), we can use the Green Ampt equation.
1. Calculate the infiltration rate (f) using the formula:
f = K + (Ss * t)
where K is the saturated hydraulic conductivity, Ss is the sorptivity, and t is the time in hours. Plugging in the values:
f = 0.34 + (0.541 * 0.5)
f ≈ 0.34 + (0.541 * 0.5)
f ≈ 0.34 + 0.2705
f ≈ 0.6105 cm/h
2. Calculate the cumulative infiltration (F) using the formula:
F = f * t
where f is the infiltration rate and t is the time in hours. Plugging in the values:
F = 0.6105 * 0.5
F ≈ 0.30525 cm
Therefore, at t = 30 minutes, the infiltration rate is approximately 0.6105 cm/h, and the cumulative infiltration is approximately 0.30525 cm.
In summary,
a) The time to ponding is 8 hours, and the initial effective saturation of the soil is approximately 18.99.
b) At t = 30 minutes, the infiltration rate is approximately 0.6105 cm/h, and the cumulative infiltration is approximately 0.30525 cm.
To learn more about Green Ampt equation :
https://brainly.com/question/28105670
#SPJ11
Consider the following hypothetical data. It (a) Compute the GDP gap for each year, using Okun's Law. (b) Which year has the highest rate of cyclical unemployment? Explain. (c) Which year is most likely to be a boom? Explain. (d) What kind(s) of unemployment are included in the natural rate? Explain why the natural rate might have risen in the US (actual data, not hypothetical) from the early 1960 s to the early 1980 s and why it might have fallen since then.
Rise in natural rate (early 1960s-early 1980s): Structural changes, oil price shocks, and labor market policies. Fall in natural rate (since early 1980s): Economic reforms and technological advancements.
What factors contributed to the rise and fall of the natural rate of unemployment in the US from the early 1960s to the early 1980s and since then?To compute the GDP gap using Okun's Law, we need to have data on the actual unemployment rate and the potential unemployment rate (also known as the natural rate of unemployment). Unfortunately, you haven't provided that information in your question. However, I can still explain the concepts and answer the remaining parts of your question.
(a) Okun's Law is an empirical relationship between the deviation of actual GDP from potential GDP and the unemployment rate. It states that for every 1% increase in the unemployment rate above the natural rate, there is a corresponding negative GDP gap. Conversely, for every 1% decrease in the unemployment rate below the natural rate, there is a positive GDP gap.
The formula to compute the GDP gap using Okun's Law is as follows:
GDP Gap = (U - U*) * Okun's Coefficient
Where:
- U is the actual unemployment rate.
- U* is the natural rate of unemployment.
- Okun's Coefficient represents the sensitivity of GDP to changes in the unemployment rate and varies depending on the country and time period.
Since you haven't provided the required data, I can't compute the GDP gap for each year.
(b) To determine which year has the highest rate of cyclical unemployment, we need the actual and natural unemployment rates for each year. Without this information, it is not possible to identify the specific year with the highest rate of cyclical unemployment.
(c) A "boom" typically refers to a period of strong economic growth characterized by high GDP, low unemployment, and high business activity. To identify the year most likely to be a boom, we would need data on GDP growth rates, unemployment rates, and other economic indicators. Without such data, it is not possible to determine the specific year most likely to be a boom.
(d) The natural rate of unemployment includes structural unemployment and frictional unemployment. Structural unemployment refers to unemployment resulting from changes in the structure of the economy, such as technological advancements or changes in consumer preferences, which lead to a mismatch between the skills possessed by workers and the skills demanded by employers.
Frictional unemployment, on the other hand, is caused by temporary transitions in the labor market, such as individuals searching for new jobs or entering the workforce for the first time.
The natural rate of unemployment is influenced by various factors, including labor market policies, demographic changes, and institutional factors.
In the case of the rise in the natural rate of unemployment in the US from the early 1960s to the early 1980s, several factors contributed to this increase. Some potential reasons include:
1. Structural changes: The US experienced significant structural changes during this period, such as the decline of manufacturing industries and the rise of the service sector. These changes led to structural unemployment as workers in declining industries faced difficulties transitioning to new sectors.
2. Oil price shocks: The 1970s saw two major oil price shocks, which increased production costs for many industries. This resulted in higher unemployment rates as firms cut back on production and laid off workers.
3. Labor market policies: There were changes in labor market policies during this period, such as increased unionization and higher minimum wages, which could have contributed to higher levels of unemployment.
In contrast, the fall in the natural rate of unemployment since the early 1980s can be attributed to various factors, including:
1. Economic reforms: The 1980s and onward witnessed a wave of economic reforms aimed at increasing labor market flexibility, reducing barriers to entry, and improving the overall efficiency of the economy. These reforms likely helped reduce structural unemployment and improve labor market conditions.
2. Technological advancements: The rapid advancement of technology, particularly in the information technology sector, created new job opportunities and reduced frictional unemployment as job search and matching processes became more efficient.
Learn more about GDP
brainly.com/question/31197617
#SPJ11
5. What was your measured density for pure water (0% sugar solution)? The density of water is usually quoted as 1.00 g/mL, but this precise value is for 4°C. Comment on why your measured density might be higher or lower than 1.00 g/mL.
The measured density for pure water (0% sugar solution) may be higher or lower than 1.00 g/mL due to factors such as temperature and impurities.
The density of water is usually quoted as 1.00 g/mL at 4°C. However, this precise value may vary depending on the temperature and the presence of impurities. At temperatures higher than 4°C, the density of water decreases due to thermal expansion. Conversely, at temperatures lower than 4°C, the density of water increases due to the formation of hydrogen bonds, resulting in a lattice-like structure.
Additionally, impurities in water can also affect its density. For example, dissolved substances such as salts or sugars can increase the density of water. In the case of a 0% sugar solution, if the measured density is higher than 1.00 g/mL, it could indicate the presence of impurities or experimental error. On the other hand, if the measured density is lower than 1.00 g/mL, it could suggest that the water sample is purer than the standard value.
Overall, the measured density of pure water can deviate from the commonly quoted value of 1.00 g/mL due to factors like temperature and impurities.
Know more about density here:
https://brainly.com/question/29775886
#SPJ11
these figures are congruent. What series of transformation moves pentagon FGHIJ onto pentagon F'G'H'I'J?
The series of transformation that move the pentagons is (d) translation, translation
What series of transformation moves the pentagonsFrom the question, we have the following parameters that can be used in our computation:
The figure
Where, we have:
Pentagon FGHIJ and pentagon F'G'H'I'J have the same orientationPentagon FGHIJ and pentagon F'G'H'I'J have the same sizeThis means that the only transformation is translation
So, the series of transformation is (d) translation, translation
Read more about transformation at
brainly.com/question/4289712
#SPJ1
A rectangular sedimentation basin treating 8,932 m3/d removes 100% of particles with settling velocity of 0.032 m/s. If the tank depth is 1.25 m and length is 6.7 m, what is the horizontal flow velocity in m/s? Report your result to the nearest tenth m/s.
The horizontal flow velocity in the rectangular sedimentation basin is approximately 0.0123 m/s.
To find the horizontal flow velocity in the rectangular sedimentation basin, we can use the equation:
Q = A * V
where Q is the flow rate, A is the cross-sectional area of the tank, and V is the flow velocity.
Given:
Flow rate (Q) = [tex]8,932 m^3/d[/tex]
Tank depth = 1.25 m
Tank length = 6.7 m
First, let's calculate the cross-sectional area (A) of the tank:
A = Depth * Length = 1.25 m * 6.7 m = [tex]8.375 m^2[/tex]
Next, we can rearrange the equation to solve for the flow velocity (V):
V = Q / A
Substituting the values:
[tex]V = 8,932 m^3/d / 8.375 m^2 \approx 1068.03 m/d[/tex]
To convert the flow velocity from m/d to m/s, we divide it by the number of seconds in a day (24 hours * 60 minutes * 60 seconds):
[tex]V = 1068.03 m/d / (24 * 60 * 60) s/d \approx 0.0123 m/s[/tex]
Therefore, the horizontal flow velocity in the rectangular sedimentation basin is approximately 0.0123 m/s.
Learn more about flow velocity at:
https://brainly.com/question/31611463
#SPJ4
You are asked to create an order for the company based on the
following instructions:
O
O
0
O
Order the number of chairs based on the increase in head count after
gaining the following information from the office manager:
Order double the number of monitors requested from the IT department.
Order 1/3 of the desks requested by the accounting department as the
company currently has a surplus of desks in other departments. If the
number is not even, round up.
Order 1/4 more than the administrative department requests of company
orientation bulletins.
Order 18 hard drives.
The office manager informs you of the following:
1. 17 people have left while 33 have joined the company in the past 60 days.
2. The IT department has requested 12 monitors.
3. The accounting department has requested 40 desks.
4. The administrative department requested 20 company orientation
bulletins.
O
.
The number of people that have left the company in the past 60 days.
The number of people that have joined the company in the past 60
days.
What should you order?
The order should include: 32 chairs, 24 monitors, 14 desks, 25 company orientation bulletins, and 18 hard drives.
To determine what should be ordered based on the given instructions and information provided by the office manager, let's break down each requirement:
1- Number of Chairs: The order for chairs should be based on the increase in headcount. Given that 17 people have left the company and 33 have joined in the past 60 days, the net increase is 33 - 17 = 16 people. Therefore, the number of chairs to be ordered should be double this increase, which is 2 * 16 = 32 chairs.
2- Number of Monitors: The IT department has requested 12 monitors. According to the instructions, we need to order double the number requested. Thus, the number of monitors to be ordered is 2 * 12 = 24 monitors.
3- Number of Desks: The accounting department has requested 40 desks. We are required to order 1/3 of the desks requested, rounding up if necessary. 1/3 of 40 is approximately 13.33, which rounds up to 14 desks.
4- Number of Company Orientation Bulletins: The administrative department requested 20 company orientation bulletins. We need to order 1/4 more than what they requested, which is 1/4 * 20 = 5 additional bulletins. Therefore, the total number of bulletins to be ordered is 20 + 5 = 25.
Number of Hard Drives: The instructions state that 18 hard drives should be ordered.
for more such questions on number https://brainly.com/question/24644930
#SPJ8
What is the first law of thermodynamics? a)energy can be neither created nor destroyed. b)It can only change forms; c)if two systems are in thermal equilibrium with a third, they are in thermal equilibrium with each other; d) the entropy of an isolated macroscopic system never decreases; e)all options are correct;
The first law of thermodynamics is that "energy can be neither created nor destroyed" (Option A).
The first law of thermodynamics, also known as the law of energy conservation, states that energy can be neither created nor destroyed. This means that the total amount of energy in a closed system remains constant over time.
This law is based on the principle of energy conservation, which is a fundamental concept in physics. It states that energy can only change forms, but the total amount of energy in a system remains constant.
For example, let's consider a simple closed system like a hot cup of coffee. When you heat the coffee, the energy from the heat source is transferred to the coffee, increasing its internal energy. As the coffee cools down, it releases heat energy to the surroundings, but the total energy in the system remains the same.
This law is applicable to various systems, from simple everyday examples like the coffee cup to more complex systems like engines or power plants. It helps us understand and analyze energy transfer and transformation processes.
So, the correct answer to the question is a) energy can be neither created nor destroyed. This option accurately describes the first law of thermodynamics, highlighting the principle of energy conservation.
Learn more about first law of thermodynamics here: https://brainly.com/question/26035962
#SPJ11
15. Consider a cylinder of fixed volume comprising two compartments that are separated by a freely movable, adiabatic piston. In each compartment is a 2.00 mol sample of perfect gas with constant volume heat capacity of 20 JK-¹ mol-¹. The temperature of the sample in one of the compartments is held by a thermostat at 300 K. Initially the temperatures of the samples are equal as well as the volumes at 2.00 L. When energy is supplied as heat to the compartment with no thermostat the gas expands reversibly, pushing the piston and compressing the opposite chamber to 1.00 L. Calculate a) the final pressure of the of the gas in the chamber with no thermostat.
The final pressure of the gas in the chamber with no thermostat is 2P₁.
To calculate the final pressure of the gas in the chamber with no thermostat, we can use the ideal gas law, which states:
PV = nRT
Where:
- P is the pressure of the gas
- V is the volume of the gas
- n is the number of moles of the gas
- R is the ideal gas constant (8.314 J/(mol·K))
- T is the temperature of the gas in Kelvin
In this case, we have a 2.00 mol sample of gas in the chamber with no thermostat. The volume of this chamber changes from 2.00 L to 1.00 L. We are given the heat capacity of the gas, which is 20 J/(K·mol), but we don't need it to solve this problem.
Initially, the temperatures and volumes of the two chambers are equal, so we can assume that the temperature of the gas in the chamber with no thermostat is also 300 K.
Using the ideal gas law, we can set up the equation as follows:
P₁V₁ = nRT₁
P₂V₂ = nRT₂
Where:
- P₁ and P₂ are the initial and final pressures of the gas, respectively
- V₁ and V₂ are the initial and final volumes of the gas, respectively
- T₁ and T₂ are the initial and final temperatures of the gas, respectively
We can rearrange these equations to solve for the final pressure, P₂:
P₂ = (P₁V₁T₂) / (V₂T₁)
Plugging in the known values:
P₂ = (P₁ * 2.00 L * 300 K) / (1.00 L * 300 K)
P₂ = (P₁ * 2.00) / 1.00
P₂ = 2 * P₁
So, the final pressure of the gas in the chamber with no thermostat is twice the initial pressure, P₁.
Therefore, the final pressure of the gas in the chamber with no thermostat is 2P₁.
Learn more about pressure thermostat:
https://brainly.com/question/2339046
#SPJ11
Which of the following sets are subspaces of R3 ? A. {(2x,3x,4x)∣x arbitrary number } B. {(x,y,z)∣x,y,z>0} C. {(x,y,z)∣x+y+z=0} D. {(x,0,0)∣x arbitrary number } E. {(x,y,z)∣−3x−4y+7z=−2} F. {(x,x+6,x−8)∣x arbitrary number }
The set given in option F satisfies all the three conditions of subspace, therefore it is a subspace. The subspaces of R3 are A, D, E and F.
Given set of options, the subspaces of R3 are: (a) {(2x,3x,4x)∣x arbitrary number }: To check if it is a subspace or not, we must check if it satisfies the three conditions of subspace:
1. Contain the zero vector - (0, 0, 0) is an element of the set.
2. Closed under addition - For u, v elements of the subspace, u + v must be an element of subspace.
3. Closed under scalar multiplication - For every u in subspace, c(u) must be an element of subspace where c is a scalar. The set given in option A satisfies all the three conditions of subspace, therefore it is a subspace.
(b) {(x,y,z)∣x,y,z>0}: It does not contain the zero vector, therefore it is not a subspace.
(c) {(x,y,z)∣x+y+z=0}: It contains the zero vector and is closed under addition but is not closed under scalar multiplication. Therefore, it is not a subspace.
(d) {(x,0,0)∣x arbitrary number }: It contains the zero vector, is closed under addition and scalar multiplication. Therefore, it is a subspace.
(e) {(x,y,z)∣−3x−4y+7z=−2}: It contains the zero vector, is closed under addition and scalar multiplication. Therefore, it is a subspace.
To know more about subspaces visit:
https://brainly.com/question/26727539
#SPJ11
Consider a stream of pure nitrogen at 4 MPa and 120 K. We would like to liquefy as great a fraction as possible at 0.6 MPa by a Joule-Thompson valve. What would be the fraction liquefied after this process? You may assume N2 is a van der Waals fluid.
Nitrogen (N2) is a typical industrial gas used for laser cutting, food packaging, and other purposes. The objective of this problem is to determine the fraction of nitrogen liquefied after it has passed through a Joule-Thompson valve while under specific conditions.
In order to determine the percentage of nitrogen liquefied after it has passed through a Joule-Thompson valve, we must first determine the enthalpy before and after the process. According to the problem, the initial state is pure nitrogen at 4 MPa and 120 K. The final state is nitrogen at 0.6 MPa and X K, which is liquefied.
The fraction liquefied after the process may be determined using the following steps: 1. Calculate the initial enthalpy of the nitrogen stream. 2. Calculate the enthalpy of the nitrogen stream after passing through a Joule-Thompson valve. 3. Determine the enthalpy of nitrogen at the final state (0.6 MPa and X K). 4. Calculate the fraction of nitrogen that has liquefied.
In the first step, we will use the Van der Waals equation to calculate the initial enthalpy of the nitrogen stream. Enthalpy may be calculated using the following formula: H = Vb(Vb - V)/RT - a/V, where V is the volume, Vb is the molar volume, R is the universal gas constant, T is the temperature, and a and b are Van der Waals constants.
Assuming that the volume of the nitrogen stream is 1 m3, we can use the following formula to calculate Vb: Vb = b - a/(RT) = 3.09 x 10-5 m3/mol. After substituting these values, we can obtain the initial enthalpy of the nitrogen stream: H = -2.75 x 104 J/mol.
The next step is to determine the enthalpy of the nitrogen stream after passing through a Joule-Thompson valve. To do this, we need to use the following formula: (dH/dT)p = Cp, where Cp is the specific heat capacity at constant pressure. At 4 MPa and 120 K, Cp is approximately 1.04 kJ/kg-K. Thus, the change in enthalpy (ΔH) may be calculated using the following formula: ΔH = CpΔT = 124.8 J/mol.
Finally, we need to calculate the enthalpy of nitrogen at the final state. This may be accomplished by using the Van der Waals equation once more. Assuming that the volume of the nitrogen stream is now 0.2 m3, we can use the following formula to calculate Vb: Vb = b - a/(RT) = 3.13 x 10-5 m3/mol. The final enthalpy of the nitrogen stream is then: Hf = -2.79 x 104 J/mol.
Using these values, we may calculate the fraction of nitrogen that has liquefied. The fraction of nitrogen that has been liquefied may be calculated using the following formula: X = (Hf - Hi)/ΔH, where Hi is the initial enthalpy of the nitrogen stream. Substituting the values yields X = 0.30 or 30%.
The fraction of nitrogen that has been liquefied is 0.30 or 30% after passing through the Joule-Thompson valve.
To know more about enthalpy :
brainly.com/question/32882904
#SPJ11
Given 10-10. 7 121.1, estimate the number of terms needed in a Taylor polynomial to guarantee an accuracy of ms are needed.
We can estimate that a small number of terms, such as n = 2 or 3, would be needed in a Taylor polynomial to guarantee an accuracy of 0.001 for the given interval.
To estimate the number of terms needed in a Taylor polynomial to guarantee a certain accuracy, we can use the remainder term formula of Taylor polynomials.
The remainder term of a Taylor polynomial is given by:
R_n(x) = f^(n+1)(c)(x-a)^(n+1) / (n+1)!
where f^(n+1)(c) is the (n+1)-th derivative of the function evaluated at some point c between a and x.
In this case, we want to guarantee an accuracy of 0.001, so we need to find the smallest value of n that satisfies:
|R_n(x)| < 0.001
Since we don't have the specific function f(x), we cannot calculate the exact value of n. However, we can use a rough estimate based on the magnitude of the interval [a, x].
In the given case, the interval is 10^(-10), which is extremely small. This suggests that a small value of n will be sufficient to guarantee the desired accuracy. In practice, for such small intervals, even a low value of n (e.g., n = 2 or 3) would likely provide an accuracy of 0.001 or better.
To learn more about Taylor polynomial click here
brainly.com/question/30481013
#SPJ11
A certain first-order reaction has a rate constant of 7.50×10^−3 s^−1 . How long will it take for the reactant concentration to drop to 1/8 of its initial value? Express your answer with the appropriate units.
The reactant concentration will take approximately 201.89 seconds to drop to 1/8 of its initial value.
In a first-order reaction, the rate of reaction is directly proportional to the concentration of the reactant. The rate law equation for a first-order reaction is given by:
rate = k[A]
where rate is the rate of reaction, k is the rate constant, and [A] is the concentration of the reactant.
In this case, the rate constant (k) is given as 7.50×10⁻³ s⁻¹. We need to determine the time it takes for the reactant concentration to decrease to 1/8 (or 1/2³) of its initial value.
The relationship between time and concentration in a first-order reaction is given by the equation:
[A] = [A₀] * e[tex]^(^-^k^t^)[/tex]
where [A] is the concentration at time t, [A₀] is the initial concentration, k is the rate constant, and e is the base of natural logarithm.
Since we want to find the time it takes for the concentration to drop to 1/8 of its initial value, we can set [A] = (1/8)[A₀]. Rearranging the equation, we have:
(1/8)[A₀] = [A₀] * e^(-kt)
Canceling out [A₀], we get:
(1/8) = e[tex]^(^-^k^t^)[/tex]
Taking the natural logarithm of both sides, we have:
ln(1/8) = -kt
Simplifying further:
-2.079 = -7.50×10⁻³ * t
Solving for t, we find:
t ≈ 201.89 seconds
Therefore, it will take approximately 201.89 seconds for the reactant concentration to drop to 1/8 of its initial value.
Learn more about initial value
brainly.com/question/17613893
#SPJ11
One serving (56 grams) of hard salted pretzels contains 2 g of fat, 48 g of carbohydrates, and 6 g of protein. Estimate the number of calories. [Hint: One gram of protein or one gram of carbohydrate typically releases about 4 Cal/g, while fat releases 9 Cal/g.]
One serving (56 grams) of hard salted pretzels contains approximately 234 calories.
To estimate the number of calories in one serving of hard salted pretzels, we need to consider the amount of fat, carbohydrates, and protein in the pretzels.
First, let's calculate the calories from fat. We know that one gram of fat releases 9 calories. The pretzels contain 2 grams of fat, so we multiply 2 by 9 to get 18 calories from fat.
Next, let's calculate the calories from carbohydrates. One gram of carbohydrate typically releases about 4 calories. The pretzels contain 48 grams of carbohydrates, so we multiply 48 by 4 to get 192 calories from carbohydrates.
Now, let's calculate the calories from protein. Like carbohydrates, one gram of protein typically releases about 4 calories. The pretzels contain 6 grams of protein, so we multiply 6 by 4 to get 24 calories from protein.
To estimate the total number of calories in one serving of hard salted pretzels, we add up the calories from fat, carbohydrates, and protein:
18 calories from fat + 192 calories from carbohydrates + 24 calories from protein = 234 calories.
Therefore, one serving (56 grams) of hard salted pretzels contains approximately 234 calories.
Learn more about pretzels calories :
https://brainly.com/question/11460467
#SPJ11