There can be 1200 pairs between the five characters and the five animals listed above.
There are 201, 600 ways to distribute the four dishes among 8 people.
When only two of the characters got their favorite animals, and the remaining three got the animals they do not really prefer, the number of pairs that can be formed will be:C(5, 2) × C(3, 3) × P(5, 5) = 10 × 1 × 120 = 1200
Therefore, there can be 1200 pairs between the five characters and the five animals listed above.
There are 4 different dishes and 2 dishes of each type.
Therefore, there are 4!/2!2! = 6 ways of choosing two distinct dishes of each type.
Since there are 8 people, one can distribute the dishes in P(8, 2)P(6, 2)P(4, 2)P(2, 2) = 201, 600 ways.
To know more about characters visit:
https://brainly.com/question/17812450
#SPJ11
Let x = (-2, 3a²), y = (-a, 1) and z = (3-a,-1) be vectors in R². Find the value(s) of a such that y and z are parallel. b] Find the value(s) of a such that x and y are orthogonal.
To find the values of a such that x and y are orthogonal, we need to calculate their dot product: x ⋅ y = (-2)×(-a) + 3a²×1 = 2a + 3a² .We want this dot product to be equal to zero:2a + 3a² = 0a(2 + 3a) = 0
Either a = 0 or 2 + 3a = 0 ⇒ a = -2/3
Therefore, the values of a that make x and y orthogonal are 0 and -2/3.
a. Let x
= (-2, 3a²), y
= (-a, 1) and z
= (3-a,-1) be vectors in R².
Find the value(s) of a such that y and z are parallel.
Two vectors are parallel if one is a multiple of the other.
Therefore, to find the values of a such that y and z are parallel, we need to check if they are multiples of each other. We can do this by comparing their components.
We can see that:-
a / (3 - a)
= 1 / -1
The cross-multiplication of the above equation is:
-a × -1
= (3 - a) × 1
Simplifying the equation gives: a = 2
Therefore, the value of a that makes y and z parallel is
2.b. Let x
= (-2, 3a²), y
= (-a, 1) and z
= (3-a,-1) be vectors in R².
Find the value(s) of a such that x and y are orthogonal.Two vectors are orthogonal if their dot product is equal to zero. To find the values of a such that x and y are orthogonal, we need to calculate their dot product:
x ⋅ y = (-2)×(-a) + 3a²×1
= 2a + 3a²
We want this dot product to be equal to zero:
2a + 3a²
= 0a(2 + 3a)
= 0
Either a
= 0 or 2 + 3a
= 0 ⇒ a
= -2/3
Therefore, the values of a that make x and y orthogonal are 0 and -2/3.
To know more about orthogonal visit:
https://brainly.com/question/32196772
#SPJ11
A survey stopped men and women at random to ask them where they purchased
groceries, at a local grocery store or online.
Grocery Options
Store Online Total
8
Women 36
Men
24
Total 60
12
20
44
36
80
What percent of the women surveyed shop online? Round your answer to the nearest
whole number percent.
Twenty of the 36 women polled engage in internet shopping. This represents around 55.6% of all the women questioned.
To find the percentage of women who shop online, we need to calculate the ratio of women who shop online to the total number of women surveyed and then multiply it by 100 to get the percentage.
According to the data provided:
- Total women surveyed: 36
- Women who shop online: 20
To find the percentage, we'll use the following formula:
(Online shoppers / Total surveyed) × 100
Percentage of women who shop online = (20 / 36) × 100 ≈ 55.6%
Therefore, approximately 55.6% of the women surveyed shop online.
In summary, out of the 36 women surveyed, 20 of them shop online. This accounts for approximately 55.6% of the total women surveyed.
For more questions on percentage, click on:
https://brainly.com/question/24877689
#SPJ8
The short sides of a parallelogram are both 12.0 cm. The acute angles of the parallelogram are 65°, and the short diagonal is 15.0 cm. Determine the length of the long sides of the parallelogram. Round your answer to the nearest tenth of a centimetre.
Answer:
15.4 cm
Step-by-step explanation:
You want the long side of a parallelogram with short side 12 cm, short diagonal 15 cm, and acute angle 65°.
Law of sinesThe law of sines can be used to find long side 'b' from short side 'a' and short diagonal 'd'. But first, we need to know the angle B opposite the long side in the triangle with sides a, b, d.
Angle AAngle B can be found using the angle sum theorem if we can find the measure of acute angle A opposite side 'a'. The law of sines helps here:
sin(A)/a = sin(65°)/d
A = arcsin(a/d·sin(65°)) = arcsin(12/15·sin(65°)) ≈ 46.473°.
B = 180° -65° -46.473° ≈ 68.527°
Long sideFinally, side 'b' is found from the relation ...
b/sin(B) = d/sin(65°)
b = 15·sin(68.527°)/sin(65°) ≈ 15.402
The length of the long side of the parallelogram is about 15.4 cm.
<95141404393>
Suppose a system of two linear equations has one solution. What must be true about the graphs of the two equations? They intersect at one point. They intersect at two points. They have the same slope. They have the same y-intercept.
The graphs of the two equations in a system with one solution must intersect at one point and have different slopes and different y-intercepts.
If a system of two linear equations has one solution, it means that the two equations represent two lines that intersect at a single point. Therefore, the correct statement is "They intersect at one point."
When two lines intersect at one point, it implies that they have different slopes and different y-intercepts. The fact that they intersect at only one point ensures that they are not parallel lines, which would never intersect. Also, they cannot be the same line, as they would intersect at infinitely many points.
For more such questions on graphs
https://brainly.com/question/29199338
#SPJ8
Find the value of x
0.03
16.2
34.8
38.5
The measure of side length x in the right triangle is approximately 38.5.
What is the numerical value of x?The figure in the image is a right triangle with one of its interior angle at 90 degrees.
Angle A = 33 degree
Adjacent to angle A = x
Opposite to angle A = 25
To solve for the missing side length x, we use the trigonometric ratio.
Note that: tangent = opposite / adjacent
Hence:
tan( A ) = opposite / adjacent
Plug in the given values and solve for x:
tan( 33° ) = 25 / x
Cross multiplying, we get:
tan( 33° ) × x = 25
x = 25 / tan( 33° )
x = 38.5
Therefore, the value of x is 38.5.
Option D) 38.5 is the correct answer.
Learn more about trigonometric ratio here: brainly.com/question/28016662
#SPJ1
Q1. Evaluate all the resources recovery and disposal options using triple bottom line approach Q2. Identify and quantify the likely amounts of hazardous waste that may be generated from households
In this scenario, we are presented with two questions. The first question asks us to evaluate all the resources recovery and disposal options using a triple bottom line approach. The second question asks us to identify and quantify the likely amounts of hazardous waste that may be generated from households.
1. Evaluating resources recovery and disposal options using a triple bottom line approach: The triple bottom line approach takes into account three aspects: economic, environmental, and social. When evaluating resources recovery and disposal options, we need to consider their economic viability, environmental impact, and social acceptability.
This involves assessing factors such as cost-effectiveness, resource conservation, pollution prevention, energy efficiency, social equity, and stakeholder engagement. By considering all three dimensions, we can make informed decisions that balance economic, environmental, and social considerations.
2. Identifying and quantifying hazardous waste from households: To identify and quantify hazardous waste generated from households, we need to consider the types of products commonly used at home, such as cleaning agents, pesticides, batteries, electronics, and pharmaceuticals. These products may contain hazardous substances that require special handling and disposal.
Quantifying the amounts of hazardous waste generated can be done by estimating the usage and disposal patterns of these products, as well as considering demographic factors and waste generation rates. This information can help in designing appropriate waste management systems, implementing recycling programs, and promoting awareness and education regarding proper disposal practices.
By evaluating resources recovery and disposal options using a triple bottom-line approach, we can ensure that our decisions consider economic, environmental, and social factors. This holistic approach promotes sustainable and responsible practices.
Identifying and quantifying hazardous waste generated from households is crucial for developing effective waste management strategies. It allows us to address potential risks associated with hazardous substances, implement proper disposal methods, and promote responsible consumer behavior. By considering both questions, we can contribute to a more sustainable and environmentally conscious society while safeguarding public health and well-being.
Learn more about resources recovery visit:
https://brainly.com/question/943779
#SPJ11
In the six sigma process DMAIC stands for: a. Diagnose, Monitor, Apply, Improve, Command b. Define, Measure, Analyse, Improve, Control c. Detect, Maintain, Associate, Interrogate, Correct d. Diagnose, Maintain, Apply, Incorporate, Correct e. Define, Monitor, Analyse, Incorporate, Correct
In the six sigma process DMAIC stands for b. Define, Measure, Analyze, Improve, Control.
In the Six Sigma process, DMAIC is an acronym that represents the five phases of the process.
1. Define: This phase involves defining the problem or goal that needs to be addressed. It includes clearly identifying the customers' requirements and expectations.
2. Measure: In this phase, relevant data is collected and measured to gain a deeper understanding of the process and identify any variations or defects. This includes determining what needs to be measured, how it will be measured, and establishing a baseline for future improvements.
3. Analyze: In the analyze phase, the collected data is analyzed to identify the root causes of the problem or variation. Various statistical tools and techniques may be used to identify patterns, trends, and potential areas for improvement.
4. Improve: Once the root causes have been identified, the focus shifts to implementing solutions and improvements. This phase involves developing and testing potential solutions to address the identified issues. The goal is to optimize the process and reduce defects or variations.
5. Control: The final phase, control, involves implementing controls and measures to ensure that the improvements made are sustained over time. This includes creating standard operating procedures, establishing metrics to monitor the process, and putting in place mechanisms to prevent the recurrence of the problem.
Overall, the DMAIC process is a systematic approach used in Six Sigma to identify and improve processes by focusing on customer requirements, data-driven analysis, and sustainable improvements.
Hence, the correct answer is Option B.
Learn more about Six Sigma process here: https://brainly.com/question/32233755
#SPJ11
Use the technique developed in this section to solve the
minimization problem. Minimize C = −2x + y subject to x + 2y ≤ 30
3x + 2y ≤ 60 x ≥ 0, y ≥ 0 ?
Minimize[tex]C = −2x + y subject to x + 2y ≤ 30, 3x + 2y ≤ 60, x ≥ 0, y ≥ 0[/tex].Method to solve linear programming problems:Select one of the constraints and solve for one variable in terms of the others (if possible).
Substituting this expression into the objective function will generate an equation with one variable only. Solve this equation to find the value of the variable corresponding to the optimal solution.
Substitute the optimal value of the variable back into the corresponding constraint to determine the value of another variable in the optimal solution.
Repeat the process until all variables have been determined.In this question, we have two constraints[tex]x + 2y ≤ 30 and 3x + 2y ≤ 60.[/tex]
We will solve one of these constraints to get one variable in terms of the others. We choose x + 2y ≤ 30 and solve for x as follows:
[tex]x + 2y ≤ 30x ≤ 30 − 2y Thus x = 30 − 2y[/tex]
Substitute this expression into the objective function
[tex]C = −2x + y.C = −2x + y = −2(30 − 2y) + y = −60 + 5y[/tex]
This gives us the equation of the objective function in terms of one variable only. We can now determine the optimal value of y by minimizing C. To do this, we differentiate C with respect to y and set the derivative equal to zero to find the critical point.
[tex]dC/dy = 5 − 0 = 5[/tex] Therefore, the function C is increasing for all values of y, which means that there is no maximum and that the minimum is −∞.Thus the solution of the minimization problem is unbounded or has no solution.
To solve this problem, we will use the technique of linear programming, which involves selecting one of the constraints and solving for one variable in terms of the others, if possible.
To know more about constraints visit:
https://brainly.com/question/32387329
#SPJ11
If a shell and tube process heater is to be selected instead of double pipe heat exchanger to heat the water ( Pwater = 1000 kg / m³ , Cp = 4180 J / kg . ° C ) from 20 ° C to 90 ° C by waste dyeing water on the shell side from 80 ° C to 25 ° C . The heat trader load of the heater is 600 kW . If the inner diameter of the tubes is 1 cm and the velocity of water is not to exceed 3 m / s , determine how many tubes need to be used in the hea exchanger .
We would need at least 1 tube in the heat exchanger.
To determine the number of tubes needed in the shell and tube process heater, we can use the equation for heat transfer:
Q = m * Cp * ΔT
Where:
Q is the heat transfer rate (600 kW)
m is the mass flow rate of water
Cp is the specific heat capacity of water (4180 J/kg.°C)
ΔT is the temperature difference (90°C - 20°C = 70°C)
First, we need to calculate the mass flow rate of water:
m = Q / (Cp * ΔT)
m = 600000 / (4180 * 70)
m ≈ 2.32 kg/s
Next, we need to calculate the cross-sectional area of a single tube using the inner diameter:
A = π * (d/2)^2
A = π * (0.01/2)^2
A ≈ 0.0000785 m^2
To find the velocity of water, we can use the equation:
V = m / (ρ * A)
Where:
V is the velocity of water
ρ is the density of water (1000 kg/m³)
V = 2.32 / (1000 * 0.0000785)
V ≈ 29.55 m/s
Since the velocity of water should not exceed 3 m/s, we need to reduce the number of tubes to achieve this. We can calculate the new cross-sectional area of a single tube using the desired velocity:
A' = m / (ρ * V)
A' = 2.32 / (1000 * 3)
A' ≈ 0.000773 m^2
Now, we can calculate the new number of tubes needed:
Number of tubes = Total cross-sectional area / New cross-sectional area
Number of tubes = Total cross-sectional area / (π * (d/2)^2)
Number of tubes = 0.0000785 / 0.000773
Number of tubes ≈ 0.101 tubes
Since we cannot have a fraction of a tube, we would need to round up to the nearest whole number. Therefore, we would need at least 1 tube in the heat exchanger.
Know more about heat exchanger:
https://brainly.com/question/12973101
#SPJ11
Given the function of f(x)=e*sinx at x = 0.5 and h = 0.25 What is the derivative of the given function using backward difference of accuracyO(h²)? a. O2.20125 b. O.137578 c. 0.157378 d. 0.137578
The derivative of the given function using backward difference of accuracy O(h²) is 0.137578 (option d).
To find the derivative of the function f(x) = e*sin(x) using backward difference of accuracy O(h²), we can apply the backward difference formula:
f'(x) ≈ [f(x) - f(x-h)] / h
Given x = 0.5 and h = 0.25, we need to evaluate f(x) and f(x-h) to compute the derivative.
Compute f(x)
Substituting x = 0.5 into the function f(x) = e*sin(x):
f(0.5) = e*sin(0.5)
Compute f(x-h)
Substituting x-h = 0.5 - 0.25 = 0.25 into the function f(x) = e*sin(x):
f(0.25) = e*sin(0.25)
Calculate the derivative
Using the backward difference formula:
f'(0.5) ≈ [f(0.5) - f(0.25)] / 0.25
Now, we substitute the values we computed:
f'(0.5) ≈ [e*sin(0.5) - e*sin(0.25)] / 0.25
After evaluating the expression, we find that the derivative is approximately 0.137578.
Learn more about derivative
brainly.com/question/32963989
#SPJ11
How many degrees of freedom are there for the atmospheric air? 1 Mark Q2. Show that (1), = (v.) = V T How the above relation simplifies for an ideal gas?
The atmospheric air has three degrees of freedom.
To show that (1), = (v.) = V T, let's break down the equation step by step:
1. (1), represents the number of degrees of freedom for a gas molecule.
2. (v.) represents the average velocity of the gas molecules.
3. V represents the volume of the gas.
4. T represents the temperature of the gas in Kelvin.
For an ideal gas, the equation simplifies even further. In an ideal gas, the gas molecules do not interact with each other and occupy no volume.
Therefore, the volume (V) can be considered negligible, and the equation becomes:
1. (1), = (v.) = T.
So, for an ideal gas, the degrees of freedom (1), are equal to the average velocity (v.) and directly proportional to the temperature (T).
To know more about degrees of freedom :
https://brainly.com/question/32093315
#SPJ11
if x=2 and y=-3 what is the value of [tex]3x^{2}[/tex]-2xy-[tex]3y^{2}[/tex]
The value of the expression [tex]3x^2 - 2xy - 3y^2[/tex] when x = 2 and y = -3 is -3.
To find the value of the expression [tex]3x^2 - 2xy - 3y^2[/tex] when x = 2 and y = -3, we substitute these values into the expression and perform the necessary calculations.
First, let's substitute x = 2 and y = -3 into the expression:
[tex]3(2)^2 - 2(2)(-3) - 3(-3)^2[/tex]
Simplifying the exponents, we have:
3(4) - 2(2)(-3) - 3(9)
Now, let's simplify the multiplication:
12 + 12 - 27
Combining like terms, we have:
24 - 27
Finally, subtracting 27 from 24, we get:
-3
Therefore, the value of the expression [tex]3x^2 - 2xy - 3y^2[/tex] when x = 2 and y = -3 is -3.
In summary, by substituting the given values of x and y into the expression and performing the necessary calculations, we find that the value of [tex]3x^2 - 2xy - 3y^2[/tex] is -3. This means that when x = 2 and y = -3, the expression evaluates to -3.
For more question on value visit:
https://brainly.com/question/843074
#SPJ8
Which of these expressions is equivalent to 30b2?
A 3b + 10b
B 3b. 10b
c9b +21b
D 9b21b
Answer:
B) 3b. 10b
Step-by-step explanation:
B) 3b. 10b = (3x10)(bxb) = 30b²
A large wastewater treatment facility, with an average flow of 220 MGD, has an average influent SO42- concentration of 400 mg/L as SO42-. The wastewater treatment facility has a large-scale biological odor control station at its headworks, with foul air treatment capacity of 180,000 cfm. The average H2S (in gas phase) concentration in the odor control station's inlet air stream is 200 PPMy/v. Please answer the following
The large wastewater treatment facility has an average flow of 220 million gallons per day (MGD). The average influent concentration of sulfate ions (SO42-) in the wastewater is 400 milligrams per liter (mg/L) as SO42-.
The facility has a biological odor control station at its headworks, which can treat foul air. The station has a treatment capacity of 180,000 cubic feet per minute (cfm). The average concentration of hydrogen sulfide (H2S) in the inlet air stream of the odor control station is 200 parts per million by volume (PPMv).
To better understand the question, let's break it down:
1. Average Flow: The wastewater treatment facility processes an average of 220 MGD. This means that, on average, 220 million gallons of wastewater pass through the facility every day.
2. Influent SO42- Concentration: The average concentration of sulfate ions (SO42-) in the influent wastewater is 400 mg/L as SO42-. This indicates the amount of sulfate ions present in each liter of wastewater entering the facility.
3. Foul Air Treatment Capacity: The odor control station at the headworks of the facility has a treatment capacity of 180,000 cfm. This means it can treat and process up to 180,000 cubic feet of foul air per minute.
4. H2S Concentration in Inlet Air Stream: The average concentration of hydrogen sulfide (H2S) in the inlet air stream of the odor control station is 200 PPMv. This indicates the amount of H2S gas present in each million parts of air entering the station.
In summary, the large wastewater treatment facility has an average flow rate of 220 MGD and an influent sulfate ion concentration of 400 mg/L as SO42-. The biological odor control station at the headworks can treat up to 180,000 cfm of foul air, and the average concentration of H2S in the inlet air stream is 200 PPMv.
To know more about wastewater treatment :
https://brainly.com/question/31158950
#SPJ11
x³ 32x5y³
O 4x³2x²y³
O 2x42xy³
O 2x² √4xy³
O 2x¹y√4xy³
The simplified expression for x³ - 32x⁵y³ is 2x³y²√y. The correct answer is O 2x³y²√y.
The expression x³ 32x5y³ can be simplified as follows:
Factor out x³ from the expression: x³(1 32x²y³)
Now factor the expression inside the parentheses as the difference of cubes:
1 32x²y³ = (1³ (2xy)³) = (1 2xy)(1² (2xy)² 2xy) = (1 2xy)(4x4y)
Substitute this expression back into the simplified form of the original expression: x³(1 32x²y³) = x³(1 2xy)(4x4y) = (x 2y)(2x²y)√4y³
The simplified expression is 2x³y²√y.
Therefore, the correct answer is O 2x³y²√y.
What is a mathematical expression?
Mathematical expressions consist of at least two numbers or variables, at least one arithmetic operation, and a statement. It's possible to multiply, divide, add, or subtract with this mathematical operation. An expression's structure is as follows: Expression: (Math Operator, Number/Variable, Math Operator)
For more questions on expression
https://brainly.com/question/1859113
#SPJ8
Q4: From the following data, determine 4H for diborane, B₂H,(g), at 298K: (1) H₂(g)+Cl₂(g)-2HCl(g) A,H-184.62 kJ mol-¹ (2) H₂(g) + O₂(g) 2H₂O(g) A,H-483.64 kJ mol-1 (3) 4 HCl(g)+O₂(g) →2Cl₂(g)+2H₂O(g)
The value of 4H for diborane (B2H6) at 298K is -2.29 kJ/Kmol.
To determine 4H for diborane, B2H6(g) at 298 K, we need to use the data given below.
Here, we will find out the heat of reaction of the given chemical reaction, then using it we will calculate the heat of formation of diborane (B2H6).
The given data is as follows:
H2(g) + Cl2(g) ⟶ 2HCl(g) ΔH = -184.62 kJ/mol
H2(g) + 1/2 O2(g) ⟶ H2O(g)
ΔH = -483.64 kJ/mol
4HCl(g) + O2(g) ⟶ 2Cl2(g) + 2H2O(g)
We can write the chemical equation for the formation of diborane as:
2B(s) + 3H2(g) ⟶ B2H6(g)
The heat of formation of diborane can be calculated using the equation below:
ΔHf° [B2H6(g)] = 1/2 [ 2ΔHf° [B(s)] + 3ΔHf° [H2(g)] - ΔHf° [B2H6(g)]]
Putting the values in the above equation, we get:
ΔHf° [B2H6(g)] = 1/2 [2(0) + 3(0) - ΔHf° [B2H6(g)]]
So, ΔHf° [B2H6(g)] = - 1/2 ΔHf° [B2H6(g)]
Similarly, we can write the chemical equation for the given reaction as:
2H2(g) + B2H6(g) ⟶ 6H(g) + 2B(s)
The heat of reaction (ΔHr°) can be calculated using the following equation:
ΔHr° = ∑nΔHf° (products) - ∑mΔHf° (reactants)
Where, m and n are the stoichiometric coefficients of the reactants and products, respectively.
Putting the values in the above equation, we get:
ΔHr° = [6(-285.83) + 2(0)] - [2(0) + 1(-36.37)]
So, ΔHr° = -1714.34 kJ/mol
Now, we can find 4H for diborane at 298K as follows:
ΔHr° = ∆Hf° [B2H6(g)] + 3/2 ΔHf° [H2(g)] - 4H4H
= [ΔHr° - ∆Hf° [B2H6(g)]] / [3/2 × ΔHf° [H2(g)]]
= [-1714.34 - (-53.39)] / [3/2 × (-483.64)]
= [1660.95] / [(-725.46)]
= -2.29kJ/Kmol
∴ The value of 4H for diborane (B2H6) at 298K is -2.29 kJ/Kmol.
To know more about stoichiometric visit :
brainly.com/question/32563206
#SPJ11
A concrete motor viaduct is to be built over a series of
concrete piers standing well above a flat plain. Suggest a suitable
construction method for the viaduct project with its method
statement
To summarize, first piers and columns will be constructed, followed by a precast segmental construction method for the superstructure. This will result in a strong and durable concrete motor viaduct.
For a concrete motor viaduct to be built over a series of concrete piers standing well above a flat plain, a suitable construction method for the viaduct project is to be suggested with its method statement.
First of all, preparation of the site will be completed to ensure a flat, stable, and smooth base for piers and columns. Earthworks, excavation, and filling will be performed to achieve this.
Afterwards, the construction of piers will be initiated. The formwork system will be installed, and then reinforcement will be placed according to the construction design. Concreting will be done in layers so that the concrete is completely consolidated, and then, curing and formwork removal will follow.
Afterward, a precast segmental construction method can be used for the viaduct superstructure. This will involve the installation of launching girders between the piers, followed by the placement of precast concrete segments.
Finally, grouting, jointing, and casting will be done between segments to provide continuity and rigidity to the structure.To summarize, first piers and columns will be constructed, followed by a precast segmental construction method for the superstructure. This will result in a strong and durable concrete motor viaduct.
To know more about superstructure visit:
https://brainly.com/question/31606872
#SPJ11
The shear stress at the walls of a 150-mm- pipe is found to be 16 Pa. The flowing fluid has a specific gravity of 0.86. The Reynold's number is 1240. Compute the velocity and shear stress 50 mm from the walls of the pipe.
The velocity of the flowing fluid at the walls of the pipe will be 2.40 m/s
The shear stress due to the fluid, 50mm away from the wall of the pipe will be 5.33 Pa.
We use the general principles of shear stress, fluid viscosity, and its effects, to figure out an answer to the question.
Shear stress is the force that acts per unit area, parallel to a surface. Due to the presence of this force parallel or tangential to the surface, it causes deformation or a movement between the adjacent layers of fluid flowing through. It offers resistance to the flow of motion.
We represent the shear stress along the walls of the pipe, with the given equation.
τ = (4 * μ * V) / D
where τ is the shearing stress
μ is known as the dynamical viscosity
V is the velocity of the fluid at the point
D is the diameter of the pipe.
We have been given some of these values in the question, such as:
τ = 16 Pa
D = 150mm = 0.15m
But we are still not aware of the velocity at the walls, as well as the dynamic viscosity.
Fortunately, we have another method, to relate them together, which is through Reynold's number.
Reynold's number, which represents the characteristic flow of a fluid, is given as follows:
Re = (ρ * V * D) / μ
where ρ is the density of the fluid. The rest of the terms retain their definitions.
We have been given the specific gravity of the fluid, in the question. We need to convert it to density.
ρ = 1000*S.G
The value '1000' is taken because of the density of water in S.I. units, from which Specific Gravity is defined originally.
ρ = 1000*0.86
ρ = 860 kg/m³
Substituting this in Reynold's number equation:
1240 = (860 * V * 0.15) / μ
V/ μ = 1240/(860*0.15)
V/ μ = 9.612
μ = V/9.612 ---------> (1)
We substitute the obtained result in the shear stress equation.
τ = (4 * μ * V) / D
16 = (4 * V * V) / (9.612*0.15)
16 * (9.612)* 0.15/4 = V²
On simplifying, we have
V² = 5.767
V = 2.40 m/s
Thus, the velocity of the fluid flowing in the pipe is 2.40m/s
But our task is not yet over, as we require the shear stress not at the walls, but 50mm away from them.
We define a relation for this purpose:
τ₅₀ = τ * (ln(50/D) / ln(y/D))
On substituting in this equation, we have:
τ₅₀ = τ * r/R
τ₅₀ = 16 * r/R
= 16 * 0.025/0.075
= 16/3
= 5.33 Pa
So, the shear stress 50mm away from the walls, will be 5.33 Pa.
For more on Shear Stress in Fluids,
brainly.com/question/32124941
#SPJ4
A 1 m diameter pipe 1400 m long. Q = 600 L/s Compute head loss if n = 0.015
Head loss due to friction in diameter of the pipe when water is flowing at the velocity is 1.5m. According to the Darcy's friction f is 0.02 and acceleration due to the gravity is 10 m/s².
Head loss due to the friction's formula can be written as:
h = [tex]\frac{f L v^{2} }{2 gd}[/tex]
where, d is diameter of the pipe,
f is the friction factor,
L is the length of the pipe,
and v here defines the velocity of the pipe
now, h = 0.02 × 1500 × 1² / 2 × 10 ×1
h = 1.5 m.
hence, the head loss of friction in pipe is 1.5m.
To learn more about diameter :
https://brainly.com/question/30460318
#SPJ4
The question is -
The head loss due to friction in pipe of 1 m diameter and 1.5 km long when water is flowing with a velocity of 1 m/s² is
three key differences among: intravenous, subcutaneous and
intramuscular
Intravenous (IV), subcutaneous (SC), and intramuscular (IM) are different routes of drug administration. The three key differences among these routes are:
1. Administration Site:
- IV: Medications are delivered directly into a vein, typically through a catheter or needle inserted into a vein.
- SC: Medications are injected into the layer of tissue just below the skin.
- IM: Medications are injected into the muscle tissue.
2. Absorption Rate:
- IV: Since the medication is directly delivered into the bloodstream, it achieves rapid and complete absorption, resulting in immediate therapeutic effects.
- SC: Medications are absorbed slowly and steadily from the subcutaneous tissue, leading to a slower onset of action compared to IV administration.
- IM: Absorption rate is faster than SC but slower than IV. It provides a moderate onset of action.
3. Volume of Administration:
- IV: Allows for large volumes of fluid and medications to be administered due to the direct access to the circulatory system.
- SC: Suitable for smaller volumes of medication, typically up to 2 mL, as the subcutaneous tissue has limited capacity for absorption.
- IM: Allows for larger volumes of medication to be administered compared to SC, usually up to 5 mL, as muscle tissue can accommodate a greater volume.
In conclusion, the key differences among IV, SC, and IM administration lie in the site of administration, the rate of absorption, and the volume of medication that can be administered. IV provides rapid absorption and allows for large volumes, while SC has slower absorption and limited volume capacity, and IM falls in between with moderate absorption and a larger volume capacity than SC. The choice of administration route depends on factors such as the medication's properties, desired onset of action, and the patient's condition.
To know more about Intravenous, visit;
https://brainly.com/question/24011307
#SPJ11
Explain the following questions briefly 1. Write the advantage of underground reservoir development over surface water development? 3pts
underground reservoir development can provide a cost-effective, efficient, and environmentally friendly way to store and manage water resources.
Underground reservoir development offers several advantages over surface water development. One of the main benefits of underground reservoir development is that it helps to conserve surface water resources.
Additionally, underground reservoirs are often less expensive to construct and maintain than surface water storage facilities. This is because underground reservoirs are typically less susceptible to evaporation and contamination than surface water storage facilities.
Underground reservoirs can also be used to store water during periods of high rainfall, which can help to prevent flooding and water damage. Furthermore, underground reservoirs can be used to improve the quality of water by filtering out impurities and contaminants.
This is especially important in areas where water sources are limited or contaminated. Underground reservoirs also have the advantage of being less visible than surface water storage facilities. This can be important in areas where land use is restricted or where aesthetics are important.
Overall,
To know more about development visit:
https://brainly.com/question/28011228
#SPJ11
MULTIPLE CHOICE Which of the following compounds would give a positive Tollens' test? A) 1-propanol B) 2-propanone C) propanoic acid D) propanal E) phenol A B C D E
Tollens' test is used to distinguish between aldehydes and ketones. The positive Tollens' test is due to the formation of silver mirror when Tollens' reagent is added to an aldehyde.
Therefore, the correct answer is D) propanal.
Propanal is an aldehyde because it has a carbonyl functional group at the end of its carbon chain. This carbonyl functional group is what gives propanal the ability to give a positive Tollens' test.In the Tollens' test.
Tollens' reagent, which contains silver ions in an alkaline solution, reacts with the carbonyl functional group of the propanal to reduce the silver ions to metallic silver. The metallic silver forms a silver mirror on the inner surface of the test tube, indicating the presence of aldehydes.
To know more about ketones visit :
https://brainly.com/question/30167255
#SPJ11
The properties of map projections are:
1.case, perspective, aspect2.case, conformality, azimuthality
3.equivalence, conformality, azimuthality, equidistance4.equidistance, perspective, aspect, conformality
Map projections preserve equivalence, conformality, azimuthality , and equidistance, representing three-dimensional curved earth on a flat surface, preserving relative areas, shapes, directions, and distances.
The properties of map projections are: 3.equivalence, conformality, azimuthality, equidistance A map projection is a method of projecting a globe's spherical surface onto a flat surface.
The properties of a map projection are the four types of mapping techniques used to depict a three-dimensional curved earth on a two-dimensional flat surface. The properties of map projections are:
Equivalence: It's the preservation of relative areas of features on the Earth's surface. Conformality: It's the preservation of shapes of small features.
Azimuthal: It's the preservation of directions between any two points. Equidistance: It's the preservation of distances between any two points on the Earth's surface. Thus, the correct option among the given options is 3. Equivalence, conformality, azimuthality, equidistance.
To know more about Map projections Visit:
https://brainly.com/question/17818991
#SPJ11
According to molt posting hum the 2016 democratic primary in a certain state, 44% of primary voters were men and 52% were women Fifty-these percent of Democrat maning in the jury supported Can Candidate A supported from the primary exit poll in this certain state is chosen at random, what is the probably that they amal?
Which of the towing probables mast be found in order to find the probability that a random Candidate A support the poi mata? Sect all that apply
A. P_r Not a supporter of Candidate A1 Democrats Woman)
b.P_r (supporter of Candidate A Democratic Woman )
C.p_r (Supporter of Candidate A Democratic Man)
D. P_r (Democratic Man)
E P_r (Democratic woman )
F.P_r(not a supporter at Candidate A1 Democratic Man)
The probably that a supporter of Candidats Arom the primary exit poll in this caman state is then at
The correct answer is that the probability that a random candidate A supporter from the primary exit poll in this certain state is a man cannot be determined without the probability of being a Democratic man.
To find the probability that a random candidate A supporter from the primary exit poll in this certain state is a man, we need to consider the following probabilities:
A. P_r (Not a supporter of Candidate A | Democratic Woman)
B. P_r (Supporter of Candidate A | Democratic Woman)
C. P_r (Supporter of Candidate A | Democratic Man)
D. P_r (Democratic Man)
E. P_r (Democratic Woman)
F. P_r (Not a supporter of Candidate A | Democratic Man)
Out of these probabilities, the relevant ones are:
C. P_r (Supporter of Candidate A | Democratic Man)
D. P_r (Democratic Man)
To find the probability that a random candidate A supporter from the primary exit poll in this certain state is a man, we need to calculate the conditional probability:
P_r (Supporter of Candidate A | Democratic Man)
Given that 44% of primary voters were men and 52% were women, we know that 44% of Democratic men supported Candidate A. Let's denote this probability as P_r (Supporter of Candidate A | Democratic Man) = 0.44.
To find the probability that a random candidate A supporter from the primary exit poll in this certain state is a man, we multiply this probability by the probability that a person is a Democratic man:
P_r (Democratic Man)
Since the information about the probability of being a Democratic man is not given in the question, we are missing a crucial piece of information needed to calculate the final probability.
Without this information, we cannot determine the probability that a random candidate A supporter from the primary exit poll in this certain state is a man.
Therefore, the correct answer is that the probability that a random candidate A supporter from the primary exit poll in this certain state is a man cannot be determined without the probability of being a Democratic man.
Learn more about probability from this link:
https://brainly.com/question/13604758
#SPJ11
Freeport-McMoRan Copper and Gold has purchased a new ore grading unit for $80,000. The unit has an anticipated life of 10 years and a salvage value of $10,000. Use the DB and DDB methods to compare the schedule of depreciation and book values for each year
The depreciation expense of the book value for 10 years with SL method is $7,000.
Straight-Line Method (SL):
The Straight-Line Method is the most basic method and is computed by subtracting the salvage value from the original cost and dividing it by the expected useful life, plus one.
Using this method, the depreciation expense for each year is calculated as:
Depreciation Expense = (Cost - Salvage Value)/(Lifespan + 1)
For this example, the depreciation expense for each year would be calculated as:
Depreciation Expense = ($80,000 - $10,000)/(10 + 1) = $7,000
The schedule of depreciation and book value for each year would look like this:
Year Depreciation Book Value
1 $7,000 $73,000
2 $7,000 $66,000
3 $7,000 $59,000
4 $7,000 $52,000
5 $7,000 $45,000
6 $7,000 $38,000
7 $7,000 $31,000
8 $7,000 $24,000
9 $7,000 $17,000
10 $7,000 $10,000
Sum-of-the-Years'-Digits Method (SOYD):
The Sum-of-the-Years'-Digits Method (SOYD) is another popular method of depreciation. It is computed by multiplying the asset’s original cost by the sum of the digits of the useful life and subtracting the salvage value.
Using this method, the depreciation expense for each year is calculated as:
Depreciation Expense = N×(Cost - Salvage Value)/(1+2+3+4+ … + N)
For this example, the depreciation expense for each year would be calculated as:
Depreciation Expense = N×($80,000 - $10,000)/(1+2+3+4+ … +10)
The schedule of depreciation and book value for each year would look like this:
Year Depreciation Book Value
1 $12,819 $67,181
2 $11,301 $55,880
3 $9,784 $46,096
4 $8,266 $37,830
5 $6,749 $30,581
6 $5,231 $24,350
7 $3,714 $19,136
8 $2,196 $14,940
9 $676 $14,264
10 $138 $14,126
Double-Declining Balance Method (DDB):
The Double-Declining Balance Method is a more aggressive approach and is calculated by multiplying the asset’s book value at the start of the year by twice the applicable straight-line rate.
Using this method, the depreciation expense for each year is calculated as:
Depreciation Expense = Book Value ×(2 × Straight-Line Rate)
For this example, the depreciation expense for each year would be calculated as:
Depreciation Expense = Book Value × (2×7,000/80,000)
The schedule of depreciation and book value for each year would look like this:
Year Depreciation Book Value
1 $14,000 $66,000
2 $11,520 $54,480
3 $8,768 $45,712
4 $5,824 $39,888
5 $3,664 $36,224
6 $1,408 $34,816
7 $0 $34,816
8 $0 $34,816
9 $0 $34,816
10 $0 $34,816
Declining Balance Method (DB):
The Declining Balance Method is a less aggressive approach and is calculated by multiplying the asset’s book value at the start of the year by the applicable straight-line rate.
Using this method, the depreciation expense for each year is calculated as:
Depreciation Expense = Book Value × (Straight-Line Rate)
For this example, the depreciation expense for each year would be calculated as:
Depreciation Expense = Book Value × (7,000/80,000)
The schedule of depreciation and book value for each year would look like this:
Year Depreciation Book Value
1 $7,000 $73,000
2 $6,024 $66,976
3 $4,914 $61,062
4 $3,770 $57,292
5 $2,597 $54,695
6 $1,398 $53,297
7 $0 $53,297
8 $0 $53,297
9 $0 $53,297
10 $0 $53,297
Therefore, the depreciation expense of the book value for 10 years with SL method is $7,000.
Learn more about the depreciation expense here:
https://brainly.com/question/17440027.
#SPJ4
what is z?
If density is 6gr cm^3
recorded mass= 1.9mg
Given dimensions 4.8mm*4.92mm
What is z ?
z a numerical measurement that describes a value's relationship to the mean of a group of values.
To find the volume, we can use the formula:
Volume = Mass / Density
First, let's convert the recorded mass from milligrams (mg) to grams (g) since the density is given in grams per cubic centimeter (g/cm^3). There are 1,000 milligrams in a gram, so 1.9 mg is equal to 0.0019 g.
Now, we can calculate the volume:
Volume = 0.0019 g / 6 g/cm^3
To proceed further, we need to determine the dimensions of the object. You mentioned the dimensions as 4.8 mm * 4.92 mm, but we need the height (or thickness) of the object as well. Could you please provide the height or any additional information about the object?
To know more about density:
https://brainly.com/question/1354972
#SPJ11
name the product of a reaction between propanamide, LiAlH4 and H2O.
if no reaction will occur write none. What if any amine is formed
from the Gabriel synthesis of 1-bromohexane?
The Gabriel synthesis of 1-bromohexane yields n-hexylamine. This is because 1-bromohexane is a primary alkyl halide and will undergo nucleophilic substitution with potassium phthalimide to form the phthalimide salt.
The product formed from the reaction between propanamide, LiAlH4, and H2O is propane-1-amine (1-aminopropane). The reaction is shown below:Propanamide + LiAlH4 + H2O → Propane-1-amine (1-aminopropane) + LiOH + Al(OH)3The product formed is an amine with the general formula RNH2. The Gabriel synthesis is a method for the preparation of primary amines. It involves the reaction of a primary alkyl halide with potassium phthalimide, followed by hydrolysis to yield the primary amine.
The Gabriel synthesis of 1-bromohexane yields n-hexylamine. This is because 1-bromohexane is a primary alkyl halide and will undergo nucleophilic substitution with potassium phthalimide to form the phthalimide salt. The phthalimide salt is then hydrolyzed to yield the primary amine, which is n-hexylamine in this case.The Gabriel synthesis is a useful method for the preparation of primary amines, particularly those that are difficult to obtain by other methods. It is a reliable and efficient method that has been widely used in organic synthesis.
To know more about primary visit:
https://brainly.com/question/29704537
#SPJ11
Answer:
Step-by-step explanation:
The reaction between propanamide (also known as propionamide), LiAlH4 (lithium aluminum hydride), and H2O (water) will result in the formation of the corresponding amine.
The reaction proceeds as follows:
Propanamide + LiAlH4 + H2O → Amine
The exact amine formed depends on the specific conditions and reactants used. In this case, propanamide will be reduced by LiAlH4 in the presence of water to yield the corresponding amine. The specific amine formed would be dependent on the substitution pattern of the propanamide molecule.
Regarding the Gabriel synthesis of 1-bromohexane, the Gabriel synthesis does not directly produce 1-bromohexane or any specific halide compound. The Gabriel synthesis is a method used to synthesize primary amines by reacting phthalimide with an alkyl halide under basic conditions, followed by hydrolysis to obtain the desired primary amine.
So, if we consider the Gabriel synthesis starting with 1-bromohexane, the product obtained would be a primary amine derived from the alkyl halide. The specific primary amine formed would depend on the substitution pattern of the alkyl halide used (in this case, 1-bromohexane).
#SPJ11
Determine the mass (B) and the volumetric dissolving power (X) of the chemical equations shown below. The chemical equation is already balanced and explains the meaning of each dissolving power. Calculate them for HCl 15 %, 28 %, and for formic acid too 1mole Caco, +2 moles HCI-----1mole CaCl2 + 1mole CO, +1mole H,0 CaMg(CO3)2 + 4HCI -- CaCl2 + MgCl2 + 2CO2 + 2H2O Specific gravity of HC115% = 1.07 Specific gravity for HCI 28 % -1.14 Density of water = 1 gram/Cm3 Density of CaCO3 = 2.71 gram/cm3 Density of dolomite = 2.84 gram/cm3 MwCaCO3 = 100.1 gram/mol Mw Dolomite = 184 gram/mol Specific acid of formic acid HCOOH= 1.22
The mass dissolving power and volumetric dissolving power of HCl 15%, 28%, and formic acid are 50.4 g CaC[tex]O_3[/tex] / g HCl and 11.2 L C[tex]O_2[/tex] / g HCl, 44.3 g CaC[tex]O_3[/tex] / g HCl and 10.6 L C[tex]O_2[/tex] / g HCl and 82.2 g CaC[tex]O_3[/tex] / g HCOOH and 22.4 L C[tex]O_2[/tex] / g HCOOH, respectively.
Mass dissolving power (B) is defined as the mass of CaC[tex]O_3[/tex] that can be dissolved by 1 mole of HCl.
Volumetric dissolving power (X) is defined as the volume of C[tex]O_2[/tex] that can be produced by 1 mole of HCl.
The mass dissolving power of HCl 15% is calculated as follows:
B = (1 mole CaC[tex]O_3[/tex] ) / (2 moles HCl) * (100.1 g CaC[tex]O_3[/tex] ) / (1.07 g HCl) = 50.4 g CaC[tex]O_3[/tex] / g HCl
The volumetric dissolving power of HCl 15% is calculated as follows:
X = (1 mole C[tex]O_2[/tex]) / (2 moles HCl) * (22.4 L C[tex]O_2[/tex]) / (1 mol C[tex]O_2[/tex]) = 11.2 L C[tex]O_2[/tex] / g HCl
The mass dissolving power of HCl 28% is calculated as follows:
B = (1 mole CaC[tex]O_3[/tex] ) / (2 moles HCl) * (100.1 g CaC[tex]O_3[/tex] ) / (1.14 g HCl) = 44.3 g CaC[tex]O_3[/tex] / g HCl
The volumetric dissolving power of HCl 28% is calculated as follows:
X = (1 mole C[tex]O_2[/tex]) / (2 moles HCl) * (22.4 L C[tex]O_2[/tex]) / (1 mol C[tex]O_2[/tex]) = 10.6 L C[tex]O_2[/tex] / g HCl
The mass dissolving power of formic acid is calculated as follows:
B = (1 mole CaC[tex]O_3[/tex] ) / (1 mole HCOOH) * (100.1 g CaC[tex]O_3[/tex] ) / (1.22 g HCOOH) = 82.2 g CaC[tex]O_3[/tex] / g HCOOH
The volumetric dissolving power of formic acid is calculated as follows:
X = (1 mole C[tex]O_2[/tex] ) / (1 mole HCOOH) * (22.4 L C[tex]O_2[/tex] ) / (1 mol C[tex]O_2[/tex] ) = 22.4 L C[tex]O_2[/tex] / g HCOOH
Therefore, the mass dissolving power and volumetric dissolving power of HCl 15%, 28%, and formic acid are as follows:
Acid Mass dissolving power (B) Volumetric dissolving power (X)
HCl 15% 50.4 g CaC[tex]O_3[/tex] / g HCl 11.2 L C[tex]O_2[/tex] / g HCl
HCl 28% 44.3 g CaC[tex]O_3[/tex] / g HCl 10.6 L C[tex]O_2[/tex] / g HCl
Formic acid 82.2 g CaC[tex]O_3[/tex] / g HCOOH 22.4 L C[tex]O_2[/tex] / g HCOOH
To learn more about mass here:
https://brainly.com/question/29082366
#SPJ4
Obtain Y(t) for the differential equation below. Use the method of Laplace transforms and partial fractions expansion. The forcing function is X(t)-u (t - 8). 16 d'y(t) dy(1) +4 +0.25y(t) 1.5x(1)-9 dt
The solution Y(t) for the given differential equation using Laplace transforms and partial fractions expansion is Y(t) = (-1/2)e^(-t/4) + (1/8)te^(-t/4).
To obtain Y(t) for the given differential equation using Laplace transforms and partial fraction expansion, let's break down the solution into several steps.
The given differential equation is:
16 d²y(t)/dt² + 4 dy(t)/dt + 0.25y(t) = 1.5x(1) - 9
First, we take the Laplace transform of both sides of the equation. Recall that the Laplace transform of the derivative of a function is given by:
L{d^n(f(t))/dt^n} = s^nF(s) - s^(n-1)f(0) - s^(n-2)f'(0) - ... - f^(n-1)(0)
Using this property, the Laplace transform of the left-hand side of the equation becomes:
16[s²Y(s) - s*y(0) - y'(0)] + 4[sY(s) - y(0)] + 0.25Y(s)
Applying the initial conditions y(0) and y'(0), the equation becomes:
16s²Y(s) - 16sy(0) - 16y'(0) + 4sY(s) - 4y(0) + 0.25Y(s) = 1.5X(1) - 9
Next, we'll take the Laplace transform of the forcing function X(t) - u(t - 8), where u(t) is the unit step function. The Laplace transform of X(t) is denoted as X(s), and the Laplace transform of u(t - 8) is given by e^(-8s)/s.
Substituting these transforms into the equation, we get:
(16s² + 4s + 0.25)Y(s) - (16sy(0) + 4y(0) - 16y'(0)) = 1.5X(1) - 9 + e^(-8s)/s
To isolate Y(s), we rearrange the equation:
Y(s) = (1.5X(1) - 9 + e^(-8s)/s + 16sy(0) + 4y(0) - 16y'(0)) / (16s² + 4s + 0.25)
Next, we need to decompose the rational function in the denominator into partial fractions. The denominator can be factored as (4s + 1)².
The partial fraction expansion is as follows:
Y(s) = (A / (4s + 1)) + (B / (4s + 1)²)
Multiplying through by the denominator and equating coefficients, we can solve for the values of A and B. Let's assume A and B as the unknowns and solve for them.
Upon solving for A and B, we get:
A = -1/2
B = 1/8
Substituting these values back into the partial fraction expansion:
Y(s) = (-1/2) / (4s + 1) + (1/8) / (4s + 1)²
Finally, we take the inverse Laplace transform of Y(s) to obtain the solution Y(t):
Y(t) = (-1/2)e^(-t/4) + (1/8)te^(-t/4)
Therefore, the solution Y(t) for the given differential equation using Laplace transforms and partial fractions expansion is Y(t) = (-1/2)e^(-t/4) + (1/8)te^(-t/4).
To learn more about Laplace transforms visit : https://brainly.com/question/29583725
#SPJ11
What happens to cellulosic material fed into a biogas digester? is it converted to biogas?
Cellulosic material is converted into biogas in a biogas digester through anaerobic digestion, a natural process that is aided by microorganisms. The efficiency of biogas production depends on several factors such as the composition of the material, temperature, pH, and retention time.
Cellulosic material is converted into biogas during anaerobic digestion, which takes place in a biogas digester. The conversion of cellulosic material into biogas in a biogas digester is a natural process that is aided by microorganisms. The microorganisms convert the cellulosic material into biogas through a series of biochemical reactions that take place inside the biogas digester.
When cellulosic material is fed into a biogas digester, it is first broken down into smaller molecules by enzymes. These smaller molecules are then converted into biogas by the microorganisms present in the biogas digester. The biogas produced is a mixture of methane, carbon dioxide, and other trace gases.
Cellulosic material that is rich in lignin, such as wood, may take longer to break down and produce less biogas than cellulosic material that is rich in cellulose, such as agricultural waste. The ideal temperature for biogas production in a biogas digester is around 35-40°C, while the ideal pH is between 6.5 and 8.0.
Know more about the anaerobic digestion
https://brainly.com/question/33247336
#SPJ11