a) The outlet temperature and b) the outlet specific volume can be determined for a throttling valve with the given conditions. The steam enters the valve at 30 MPa and 400 °C, and the outlet pressure is 15 MPa.
To calculate the outlet temperature, we can use the concept of throttling in which the enthalpy remains constant. Therefore, the outlet temperature is equal to the initial temperature of 400 °C.
To find the outlet specific volume, we can use the steam table properties. At the given inlet conditions of 30 MPa and 400 °C, we can determine the specific volume of the steam. Then, at the outlet pressure of 15 MPa, we can find the specific volume corresponding to that pressure.
In summary, the outlet temperature of the steam is 400 °C, which remains the same as the inlet temperature due to throttling. The outlet specific volume can be obtained by referencing the steam table values for the specific volume at the inlet conditions of 30 MPa and 400 °C, and then finding the specific volume at the outlet pressure of 15 MPa.
To learn more about steam click here, brainly.com/question/31830018
#SPJ11
A packed tower is to be used to remove acetone from an air stream with pure water. The inlet acetone-rich gas stream has a concentration of 3.25 mole% acetone. The inlet gas flow rate is 1,003 lb mole/hr. The design acetone recovery is 97.5%. The equilibrium relationship based on acetone mole fractions is y= 1.7x. The minimum water flow rate (lb mole/hr) for the specified separation is most nearly:
To remove acetone from an air stream using a packed tower with pure water, the minimum water flow rate required for the specified separation is approximately 2,819 lb mole/hr.
In order to determine the minimum water flow rate for the acetone removal, we need to consider the design acetone recovery, inlet gas flow rate, and the equilibrium relationship between acetone mole fractions.
The design acetone recovery is given as 97.5%, which means that we aim to remove 97.5% of the acetone from the gas stream. The inlet gas flow rate is stated as 1,003 lb mole/hr.
The equilibrium relationship between acetone mole fractions is given as y = 1.7x, where y represents the mole fraction of acetone in the gas phase and x represents the mole fraction of acetone in the liquid phase.
To calculate the minimum water flow rate, we need to find the point where the liquid and gas phase concentrations reach equilibrium. At this point, the acetone mole fraction in the gas phase (y) will be equal to the acetone mole fraction in the liquid phase (x).
Given the equilibrium relationship, we can set y = 1.7x. Since the design acetone recovery is 97.5%, the mole fraction of acetone remaining in the gas phase after separation will be (100 - 97.5) / 100 = 0.025.
Substituting this value into the equation y = 1.7x, we can solve for x, which represents the mole fraction of acetone in the liquid phase at equilibrium. Solving the equation gives x = 0.0147.
The minimum water flow rate can now be calculated by multiplying the inlet gas flow rate by the mole fraction of acetone in the gas phase that remains after separation: 1,003 lb mole/hr * 0.025 = 25.08 lb mole/hr.
Therefore, the minimum water flow rate required for the specified separation is most nearly 2,819 lb mole/hr.
To learn more about acetone click here, brainly.com/question/31838988
#SPJ11
How many monobrominated products (ignore steroisomers) does 1, 3- dimethyl cyclohexane can form with Br_2 under high energy photons?a. 4 b. 5 c. 6 d. none of the choices
1,3-dimethyl cyclohexane is one of the dimethyl cyclohexane isomers that exist.
It is a colorless liquid. In addition to its cyclohexane ring, it has two methyl groups, each of which is connected to a different carbon atom.
The monobromination of 1,3-dimethyl cyclohexane is a major reaction.
The following monobrominated products can be formed by 1,3-dimethyl cyclohexane with Br2 under high-energy photons:
Option A: 4 [CORRECT ANSWER]
Option B: 5
Option C: 6
Option D: none of the choices
High-energy photons, in this case, refer to light or radiation with high-energy wavelengths that can excite the bromine atoms' electrons.
To know more about isomers visit;
https://brainly.com/question/32508297
#SPJ11
#5
NaBiO3 is a rare sodium salt that is slightly soluable in water. How can it be produced? Provide chemical reaction equations and explain briefly.
Sodium bismuthate (NaBiO3) can be produced by the reaction of bismuth(III) oxide (Bi2O3) with sodium hydroxide (NaOH) in water.
Here's the chemical equation for the reaction: Bi2O3 + 6NaOH + 3O2 → 2NaBiO3 + 3H2O. In this reaction, bismuth(III) oxide reacts with sodium hydroxide and oxygen gas to form sodium bismuthate and water. The oxygen gas is typically provided by bubbling air through the reaction mixture. The reaction takes place in an aqueous medium, where the bismuth(III) oxide dissolves in sodium hydroxide solution to form sodium bismuthate. The resulting sodium bismuthate is slightly soluble in water, which means that it remains in the solution rather than precipitating out as a solid.
This method provides a way to produce sodium bismuthate, which is a rare compound used in various applications such as inorganic synthesis and as an oxidizing agent in organic chemistry.
To learn more about sodium hydroxide click here: brainly.com/question/10073865
#SPJ11
What will be the chemical compound of the alloy when mixing
9wt.% Al, 3wt.% Ni and 88wt.% Mg in a closed system during
heating?
Magnesium nickel aluminum hydride is the chemical compound of the alloy formed when mixing 9wt.% Al, 3wt.% Ni and 88wt.% Mg in a closed system during heating.
When the given 9wt.% Al, 3wt.% Ni and 88wt.% Mg metals are mixed and heated in a closed system, the chemical compound formed is known as magnesium nickel aluminum hydride.
An alloy is a homogeneous mixture of two or more metals or a metal and non-metal. Due to the combination of metals, the new substance formed has unique properties that aren't present in the constituent elements individually. A chemical compound is a substance made up of two or more elements. They're combined chemically in a set ratio to form a unique material.
Chemical bonds bind the atoms of these elements together.The given 9wt.% Al, 3wt.% Ni, and 88wt.% Mg metals can form magnesium nickel aluminum hydride when they're mixed and heated in a closed system. This is due to the strong interaction between these elements and the hydrogen present in the environment during heating.Therefore, magnesium nickel aluminum hydride is the chemical compound of the alloy formed when mixing 9wt.% Al, 3wt.% Ni and 88wt.% Mg in a closed system during heating.
Learn about alloy : https://brainly.com/question/16935193
#SPJ11
5. Which of the following is true 1 point for a critically damped control system. The damping coefft is O >1 O
The correct answer is "The damping coefficient is 1."
A critically damped control system is a type of control system that returns to its equilibrium state as quickly as possible without overshooting it. For a critically damped control system, the damping coefficient is equal to 1.
Therefore, the statement "The damping coefficient is O >1" is false.
A damping effect is one that reduces or stops oscillation in an oscillatory system by affecting it internally or externally. Physical systems experience damping as a result of processes that release the oscillation's stored energy.
Examples include viscous drag in mechanical systems, resistance in electronic oscillators, and light absorption and scattering in optical oscillators (a liquid's viscosity can inhibit an oscillatory system, causing it to slow down; see viscous damping).
Other oscillating systems, like those seen in biological systems and bicycles, can benefit from damping that is not reliant on energy loss(For instance, suspension (mechanics)). Contrary to friction, which acts on a system as a dissipative force. Damping can result from or be caused by friction.
Know more about coefficient here:
https://brainly.com/question/13433635
#SPJ11
k) Describe the role of equipment reliability information and manufacturers recommended service intervals in setting both planned maintenance schedules. Explain why it is essential to inspect and test safety critical plant systems regularly between planned maintenance intervals.
Equipment reliability information and manufacturers' recommended service intervals play a crucial role in establishing planned maintenance schedules.
Equipment reliability information provides data on the historical performance, failure rates, and mean time between failures (MTBF) of equipment. This information helps establish the optimal frequency of maintenance activities to minimize the risk of unexpected breakdowns and optimize equipment availability. Manufacturers' recommended service intervals provide guidelines on when specific maintenance tasks, such as lubrication, filter replacements, or component inspections, should be performed based on their expertise and knowledge of the equipment.
However, even with planned maintenance schedules in place, it is essential to regularly inspect and test safety critical plant systems between those intervals. Safety critical systems, such as emergency shutdown systems or fire suppression systems, are vital for ensuring the safe operation of a plant. Regular inspections and testing allow for early detection of potential faults, degradation, or malfunctions that may compromise system integrity or safety. By conducting inspections and tests, any issues can be identified and addressed promptly, reducing the risk of equipment failure and ensuring the continuous protection of personnel, assets, and the environment.
To learn more about lubrication click here, brainly.com/question/24934810
#SPJ11
Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr(s) o Assignment: Given the following notation for a voltaic cell Draw a diagram of the cell illustrating the anode, cathode, salt bridge, electrodes with their respective ions in solution and include a meter of voltage (voltmeter) Write the oxidation and reduction reactions. Determine the electrons transferred. write the net reaction Determine the emf (voltage) of the cell Calculate the net wo
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
Oxidation reaction: Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction: Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred: 2 electrons in the oxidation reaction and 3 electrons in the reduction reaction.
Net reaction: Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell: 0.02 V
Net work: -3.86 kJ (negative value indicates work is done on the system)
Diagram of the Voltaic Cell: Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr (s)
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
| Salt Bridge |
Zn²+ (aq) || Cr³+ (aq)
_______________
| |
| Voltmeter |
|_______________|
Oxidation reaction (at the anode):
Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction (at the cathode):
Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred:
2 electrons are transferred in the oxidation reaction (Zn -> Zn²+)
3 electrons are transferred in the reduction reaction (Cr³+ + 3e- -> Cr)
Net reaction:
Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell:
The EMF of the cell can be determined using the standard reduction potentials of Zn²+ and Cr³+ ions. The standard reduction potential for Zn²+ is -0.76 V, and for Cr³+ is -0.74 V. The EMF of the cell is the difference between the reduction potentials:
EMF = E°(cathode) - E°(anode)
EMF = -0.74 V - (-0.76 V)
EMF = 0.02 V
The net work done by the cell can be calculated using the equation:
Work = -nFEMF
where n is the number of moles of electrons transferred, F is the Faraday constant (96485 C/mol), and EMF is the electromotive force of the cell.
Work = -(2 mol + 3 mol) * 96485 C/mol * 0.02 V
Work = -3859.4 J (or -3.86 kJ)
Learn more about Cathode at https://brainly.com/question/2349926
#SPJ11
The cultures of prehistoric humans are known mostly through the excavation of stone tools and other relatively imperishable artifacts. The early tool making traditions are often referred to as being paleolithic (literally "Old Stone Age). The Oldowan and Acheulian tool traditions of the first humans were the simplest applied research basic research Scientihe thought O philosophies technologies
The cultures of prehistoric humans are primarily known through the excavation of stone tools and other durable artifacts, such as the Oldowan and Acheulian tool traditions.
Stone tools and imperishable artifacts serve as key archaeological evidence for understanding prehistoric cultures. Through meticulous excavation and analysis, archaeologists have been able to piece together the lifestyles, technological advancements, and social behaviors of early human societies. The term "paleolithic" refers to the Old Stone Age, a time when humans relied on stone tools as their primary implements.
The Oldowan tool tradition is considered the earliest stone tool industry, dating back around 2.6 million years ago. It is characterized by simple tools, such as choppers and scrapers, which were crafted by flaking off pieces from larger stones. These tools were primarily used for basic activities like butchering and processing animal carcasses.
Later, the Acheulian tool tradition emerged around 1.76 million years ago, representing an advancement in stone tool technology. Acheulian tools, such as handaxes and cleavers, were more refined and standardized, showcasing an increased level of sophistication in tool-making techniques. These tools served a wide range of purposes, including hunting, woodworking, and shaping raw materials.
By studying the Oldowan and Acheulian tool traditions, researchers gain valuable insights into the cognitive abilities, cultural development, and technological progress of early humans. The examination of these artifacts provides evidence of their adaptability, problem-solving skills, and the gradual refinement of their tool-making techniques over time.
Learn more about prehistoric humans
brainly.com/question/28301954
#SPJ11
Prompt
Answer the following questions. Give details to explain your reasoning in each response.
1.) How do we name the compound CO2? Provide a detailed explanation for your answer. (30 points)
2.) How do we name the compound N2O5? Provide a detailed explanation for your answer. (30 points)
3.) Describe a scenario when we would omit the use of the prefix “mono”. Give an example and name the compound. (35 points)
Answer:
The compound CO2 is named carbon dioxide.Explanation: In chemical nomenclature, the name of a compound is derived from its constituent elements. Carbon dioxide consists of two elements: carbon (C) and oxygen (O). To name binary covalent compounds like CO2, we use a system called the Stock system or Stock nomenclature.
In this system, the first element's name remains unchanged, while the second element's name is modified to end in "-ide." In the case of carbon dioxide, "carbon" remains the same, and "oxygen" is modified to become "oxide." Therefore, the compound is named "carbon dioxide."
The compound N2O5 is named dinitrogen pentoxide.Explanation: Similar to the previous example, we use the Stock system to name binary covalent compounds. In the compound N2O5, there are two nitrogen (N) atoms and five oxygen (O) atoms. The prefix "di-" is used to indicate two nitrogen atoms, and the root name "nitrogen" remains unchanged. The prefix "penta-" is used to indicate five oxygen atoms, and the root name "oxygen" is modified to become "oxide." Therefore, the compound is named "dinitrogen pentoxide."
The prefix "mono" is typically omitted when there is only one atom of the first element present in a compound.Explanation: The prefix "mono-" is used to indicate a single atom of the first element in a compound. However, it is generally omitted in naming compounds when there is only one atom of the first element.
An example of a compound where we omit the use of the prefix "mono-" is carbon monoxide (CO). Carbon monoxide consists of one carbon atom and one oxygen atom. Instead of naming it "monocarbon monoxide," we simply name it "carbon monoxide." The omission of the prefix "mono-" is a convention to avoid redundancy since the compound name already indicates that there is only one atom of carbon present.
Therefore, the scenario when we omit the use of the prefix "mono-" is when there is only one atom of the first element in a compound, as exemplified by carbon monoxide.
6.44 From data in the steam tables, determine numerical values for the following: (a) G¹ and Gº for saturated liquid and vapor at 900 kPa. Should these be the same? (b) AH/T and AS for saturation at 900 kPa. Should these be the same? (c) VR, HR, and SR for saturated vapor at 900 kPa. From data for Psat at 875 and 925 kPa, estimate a value for dpsat/dT at 900 kPa and apply the Clapeyron equation to estimate AS at 900 kPa. How well does this result agree with the steam-table value? Apply appropriate generalized correlations for evaluation of VR, HR, and SR for saturated vapor at 900 kPa. How well do these results compare with the values found in (c)?
Various properties of saturated liquid and vapor at 900 kPa are determined using steam tables and calculations. The values for G¹ and Gº for saturated liquid and vapor at 900 kPa should be different. The values for AH/T and AS for saturation at 900 kPa should also be different. Additionally, the values for VR, HR, and SR for saturated vapor at 900 kPa can be estimated using the Clapeyron equation and generalized correlations.
(a) The values for G¹ and Gº, which represent the Gibbs free energy, will be different for saturated liquid and vapor at 900 kPa. G¹ refers to the Gibbs free energy of saturated liquid, while Gº represents the Gibbs free energy of saturated vapor. These values will differ due to the different states and properties of the two phases.
(b) AH/T and AS, which represent the enthalpy and entropy divided by temperature, respectively, should be different for saturation at 900 kPa. AH/T quantifies the change in enthalpy per unit temperature, and AS represents the change in entropy per unit temperature. Since saturated liquid and vapor have different enthalpy and entropy values, the ratios AH/T and AS will also differ.
(c) To estimate the value of dpsat/dT at 900 kPa, the steam-table values for Psat at 875 and 925 kPa can be used to calculate the difference in saturation pressure with respect to temperature. The Clapeyron equation can then be applied to estimate AS at 900 kPa. However, the accuracy of this estimation should be assessed by comparing it to the steam-table value for AS at 900 kPa.
For the evaluation of VR, HR, and SR at 900 kPa, appropriate generalized correlations can be used. These correlations are derived based on experimental data and can provide estimates for these properties. However, it is important to compare these results with the values obtained in part (c) to assess their accuracy and agreement.
Learn more about Clapeyron : brainly.com/question/29409537
#SPJ11
Identify which animal would be classified in the phylum Chordata.
Tick
Fish
Flower
Spider
The animal that would be classified in the phylum Chordata is the Tick. The correct answer is option Tick.
The phylum Chordata is a taxonomic group that contains animals with notochords at some point in their lives. A notochord is a flexible rod that runs along the length of the body, providing support and structure for the animal's movement. The Tick is a member of the phylum Arthropoda, which includes insects, crustaceans, and arachnids. Arthropods have an exoskeleton, segmented bodies, and jointed appendages. The Fish would also be classified in the phylum Chordata, as they have a notochord throughout their entire lives. Fish are aquatic animals that breathe through gills and are characterized by scales, fins, and a streamlined body shape. The Flower and Spider, on the other hand, are not classified in the phylum Chordata. Flowers are part of the plant kingdom, while spiders are members of the phylum Arthropoda, but they do not have a notochord, which is a defining characteristic of the Chordata.In summary, the animal that would be classified in the phylum Chordata is the Tick, while Fish is also a member of this group. Flowers and Spiders are not members of this phylum.For more questions on Chordata
https://brainly.com/question/23139326
#SPJ8
. Water trickles by grarity over a bed of particles, each 1 mm diameter in or bed of dia 6 cm and height of 2 m. The water is fed from a reserra ir whose diameter is much Larger than that of the packed bed, with water maintained at a height of 0.1 m above the top of the bed. The velocity of water is 4.025×10 −3
m/ sre and viscosity is 1CP. Density of trater is 1000 kg/m 3
and partieles hare a spheriatys Calculate the porosity of the bed by Nenton Raphson Method. L
ΔP
= (ϕ s
Dp) 2
ε 3
150nv(1−ε) 2
+ ϕ s
D p
ε 3
1.75pv 2
(1−ε)
The final value of ε obtained will be the porosity of the bed.
To calculate the porosity of the bed using the Newton-Raphson method, we need to solve the given equation:
LΔP = (ϕsDp)²ε(3150nv(1-ε)²) + ϕsDpε(31.75pv²(1-ε))
Where:
L = Height of the bed = 2 m
ΔP = Pressure drop across the bed (unknown)
ϕs = Sphericity of the particles (unknown)
Dp = Diameter of the particles = 1 mm = 0.001 m
ε = Porosity of the bed (unknown)
nv = Viscosity of water = 1 CP = 0.001 kg/(m⋅s)
pv = Density of water = 1000 kg/m³
v = Velocity of water = 4.025×10^-3 m/s
The Newton-Raphson method requires an initial guess for the unknown variable. Let's start with ε = 0.4.
Substituting the given values into the equation:
2ΔP = (ϕs(0.001)²)(0.4)(3150(0.001)(4.025×10^-3)(1-0.4)²) + ϕs(0.001)(0.4)(31.75(1000)(4.025×10^-3)²(1-0.4))
Now, let's solve this equation iteratively using the Newton-Raphson method:
1. Calculate the value of the function (F) using the initial guess:
F = 2ΔP - (ϕs(0.001)²)(0.4)(3150(0.001)(4.025×10^-3)(1-0.4)²) - ϕs(0.001)(0.4)(31.75(1000)(4.025×10^-3)²(1-0.4))
2. Calculate the derivative of the function (F') with respect to ε:
F' = -2(ϕs(0.001)²)(3150(0.001)(4.025×10^-3)(1-0.4)²) - (ϕs(0.001)(31.75(1000)(4.025×10^-3)²(1-0.4)) - (ϕs(0.001)²)(3150(0.001)(4.025×10^-3)(2)(0.4)(1-0.4))
3. Update the guess for ε using the equation:
ε_new = ε - (F / F')
4. Repeat steps 1-3 until the difference between ε and ε_new is negligible.
Continue this iteration until you reach the desired level of accuracy. The final value of ε obtained will be the porosity of the bed.
To know more about Newton-Raphson method related question visit:
https://brainly.com/question/32721440
#SPJ11
A benzene-toluene mixture is to distilled in a simple batch distillation column. If the mixt re contains 60% benzene and 40% toluene, what will be the boiling point of mixture if it is to be distilled at 2 atm? (A) 90 B) 122 115 (D) 120
To determine the boiling point of the benzene-toluene mixture at 2 atm, we need to consider the vapor-liquid equilibrium of the mixture.
The boiling point of a liquid corresponds to the temperature at which its vapor pressure is equal to the external pressure. Given that the mixture contains 60% benzene and 40% toluene, we can assume ideal behavior and calculate the vapor pressure of each component using Raoult's law: P_benzene = X_benzene * P°_benzene; P_toluene = X_toluene * P°_toluene, Where X_benzene and X_toluene are the mole fractions of benzene and toluene, respectively, and P°_benzene and P°_toluene are the vapor pressures of pure benzene and toluene at the given temperature. Assuming ideal behavior, the total vapor pressure of the mixture is given by: P_total = P_benzene + P_toluene.
Since the mixture is distilled at 2 atm, we can set up the equation: P_total = 2 atm. By substituting the known values and solving the equation, we can determine the boiling point of the mixture. Note: The given answer options (90, 122, 115, 120) do not correspond to the boiling points in degrees Celsius. It is necessary to convert the obtained boiling point from Kelvin to Celsius to match the provided answer options.
To learn more about boiling point click here: brainly.com/question/2153588
#SPJ11
Please read the question carefully and write the
solution step by step, Thank you.
Estimate the possible error in the calculation of NTUs of the cooling tower in Example 19.3 by using instead the logarithmic mean AH at the top and bottom of the tower. JI
. . EXAMPLE 19.3. A counter
The logarithmic mean difference is used in the calculation of the effectiveness of heat exchangers, which is important in the thermal design of many devices and systems.
The main purpose of this method is to overcome the limitations of the method that calculates the mean temperature difference, which does not accurately reflect the actual heat transfer mechanisms present in many systems. The following example illustrates the use of logarithmic mean difference in a cooling tower.
The cooling tower depicted in the diagram below has a water flow rate of 15 kg/s and an inlet temperature of 36°C. The outlet temperature is 29°C. The atmosphere is dry, and its temperature is 24°C. The rate of evaporation is 0.02 kg/s, and the specific heat of water is 4.18 kJ/kg·K.
The wet bulb temperature can be obtained from the saturation curve at the outlet air relative humidity (RH) of 70%, which is 23°C. Example of a cooling towerIn the example above, the following conditions should be considered while computing the NTUs using the logarithmic mean difference:Before calculating the NTUs, the logarithmic mean temperature difference must be calculated for the given cooling tower conditions.
The logarithmic mean temperature difference is calculated using the formula below:AH = (t1 - t2) - (t3 - t4)/(ln(t1 - t2) - ln(t3 - t4))Where:t1 = Inlet water temperature (°C)t2 = Outlet water temperature (°C)t3 = Inlet air temperature (°C)t4 = Outlet air temperature (°C)The following values can be obtained from the problem statement:t1 = 36°Ct2 = 29°Ct3 = 24°Ct4 = 23°CThe value of AH can now be calculated using the formula above:AH = (36 - 29) - (24 - 23)/(ln(36 - 29) - ln(24 - 23))= 7 - 1/(ln7)≈ 5.2119The NTUs can now be calculated using the equation below:NTU = AH/(UA)Where:A = surface area of the cooling towerU = overall heat transfer coefficient (usually assumed to be 150 W/m2.K).
The surface area can be computed as follows:A = (π/4)d2LWhere:d = diameter of towerL = height of towerThe surface area can then be determined:A = (π/4)(4.2)2(4.5)≈ 62.28 m2Now, the NTU can be calculated:NTU = 5.2119/(150 x 62.28)≈ 0.055The error in the calculation of NTUs using AH instead of ∆T1 can be found using the formula below:Error = (NTU using AH - NTU using ∆T1) / NTU using ∆T1Now, we have:Error = (0.055 - 0.039)/0.039≈ 0.41 or 41%
Therefore, the error in the calculation of NTUs using AH instead of ∆T1 is 41%.
To know more about logarithmic mean click here:
https://brainly.com/question/13039659
#SPJ11
What is the mass per volume (mg/m³, to the nearest 1 mg/m³) concentration of sulfur dioxide, SO2, present in air at a concentration of 20 ppm(v) at a temperature of 18C and atmospheric pressure of 0
The mass per volume concentration of sulfur dioxide (SO₂) in air, with a concentration of 20 ppm(v), at a temperature of 18°C and atmospheric pressure of 0.985 atm, is approximately 529 mg/m³.
To calculate the mass per volume concentration of SO₂, we need to convert the concentration from parts per million by volume (ppm(v)) to mass per volume (mg/m³) using the ideal gas law.
The ideal gas law equation is given as:
PV = nRT
Where:
P = Pressure (atm)
V = Volume (m³)
n = Number of moles
R = Gas constant (0.0821 atm·L/mol·K)
T = Temperature (K)
To convert ppm(v) to mg/m³, we need to calculate the number of moles of SO₂ present in a known volume of air at a given temperature and pressure.
1. Convert ppm(v) to a fraction: 20 ppm(v) = 20/1,000,000 = 0.00002
2. Calculate the number of moles of SO₂:
n = (0.00002) * V
Assuming a volume of air of 1 m³, the number of moles of SO₂ becomes:
n = (0.00002) * 1 = 0.00002 mol
3. Convert temperature from Celsius to Kelvin: 18°C + 273.15 = 291.15 K
4. Use the ideal gas law to solve for pressure:
(0.985 atm) * (1 m³) = (0.00002 mol) * (0.0821 atm·L/mol·K) * (291.15 K)
Solving for the volume, V = 529.22 L
5. Convert volume to cubic meters: V = 529.22 L = 0.52922 m³
6. Calculate the mass of SO₂:
Mass = n * molar mass
Assuming the molar mass of SO₂ is 64.06 g/mol,
Mass = (0.00002 mol) * (64.06 g/mol) = 1.2812 mg
7. Convert mass to mg/m³:
Concentration = Mass / Volume
Concentration = 1.2812 mg / 0.52922 m³ ≈ 529 mg/m³ (to the nearest 1 mg/m³)
The mass per volume concentration of sulfur dioxide (SO₂) in air, with a concentration of 20 ppm(v), at a temperature of 18°C and atmospheric pressure of 0.985 atm, is approximately 529 mg/m³. This calculation helps determine the mass of SO₂ present in a given volume of air and is useful for assessing air quality and environmental impact.
To know more about sulfur dioxide (SO₂) , visit
https://brainly.com/question/30995531
#SPJ11
Locate the Fermi energy level of GaAs with n = 3.1 x 1018 cm3 at T = 400K and compare it when T = 500K. Below is the table of effective density of states for Si, GaAs and Ge at room temp. N₂ (cm ³) 1.04 × 10¹⁹ 7.0 × 10¹8 6.0 × 10¹8 N₁ (cm ³) 2.8 × 10¹9 Silicon Gallium arsenide 4.7 x 10¹7 Germanium 1.04 × 10¹⁹ 3. Repeat problem number 2 but, this time the majority carrier of GaAs is hole with p = 3.1 x 1018 cm-3
The Fermi energy level of GaAs with n = 3.1 x 10^18 cm^3 at T = 400K is located between the energy levels corresponding to N1 and N2 in the table. When T = 500K, the Fermi energy level will shift due to the change in temperature.
The Fermi energy level represents the energy level at which the probability of occupancy of electron states is 0.5 at a given temperature. In the provided table, N1 and N2 correspond to the effective density of states for GaAs. To locate the Fermi energy level, we compare the carrier concentration (n) with the effective density of states.
For GaAs with n = 3.1 x 10^18 cm^3, we compare this value with N1 and N2 in the table. Based on the comparison, we can determine the energy level at which the Fermi energy lies. However, the exact location cannot be determined without additional information about the specific energy levels associated with N1 and N2.
For T = 500K, the Fermi energy level will shift due to the change in temperature. The shift can be determined by considering the change in carrier concentration and comparing it with the effective density of states. Again, the specific location of the Fermi energy level will depend on the energy levels associated with the effective density of states for GaAs.
Learn more about Fermi energy : brainly.com/question/31499121
#SPJ11
QUESTION 2 (PO2, CO3, C5) Ammonium nitrate (NH.NO;) is used commonly in explosives, fertilisers, in pyro-techniques to produce herbicides, and insecticides; and in the manufacture of nitrous oxide (la
Ammonium nitrate (NH₄NO₃) is commonly used in various applications such as explosives, fertilizers, pyrotechnics, herbicides, insecticides, and in the manufacture of nitrous oxide (laughing gas).
Explosives: Ammonium nitrate is a widely used ingredient in explosive mixtures due to its high nitrogen content. When combined with a fuel source, such as diesel fuel or other combustible materials, it can create a highly explosive mixture. However, due to its potential for misuse in improvised explosive devices (IEDs), strict regulations and safety measures are in place for the storage, transportation, and handling of ammonium nitrate.
Fertilizers: Ammonium nitrate is a significant component of nitrogen-based fertilizers. It provides a readily available source of nitrogen, which is essential for plant growth. The nitrate ion (NO₃⁻) and ammonium ion (NH₄⁺) released upon dissolution of ammonium nitrate in soil provide plants with the necessary nitrogen for protein synthesis and overall development.
Pyrotechnics: Ammonium nitrate is used in pyrotechnic formulations, particularly as an oxidizing agent. When combined with certain fuels, it can produce colorful flames and explosive effects in fireworks displays and other pyrotechnic events.
Herbicides and Insecticides: Ammonium nitrate can be utilized as a component in herbicides and insecticides due to its ability to disrupt metabolic processes in plants and insects. However, its use as a pesticide is declining due to environmental concerns and stricter regulations.
Manufacture of Nitrous Oxide: Ammonium nitrate can also serve as a precursor in the production of nitrous oxide (N₂O), commonly known as laughing gas. Nitrous oxide is used as an anesthetic agent in medical and dental procedures, as well as in whipped cream dispensers and as a recreational drug.
Ammonium nitrate finds applications in various industries, including explosives, fertilizers, pyrotechnics, herbicides, insecticides, and the manufacture of nitrous oxide. It is important to handle and use ammonium nitrate safely and in accordance with regulations to prevent accidents and ensure environmental responsibility. Please note that the information provided is a general overview and does not cover all aspects and uses of ammonium nitrate in detail.
To know more about fertilizers , visit;
https://brainly.com/question/28297546
#SPJ11
QUESTION 2 (PO2, CO3, C5) Ammonium nitrate (NH.NO;) is used commonly in explosives, fertilisers, in pyro-techniques to produce herbicides, and insecticides; and in the manufacture of nitrous oxide (laughing gas).
What is the equation for the characteristic time for some molecule to diffuse? And to advect? How do these equations change if you are referring to heat diffusing and advecting? 47. What is the equation for and meaning of the Peclet number? What does this tell us about the importance of diffusion?
The equation for the characteristic time for a molecule to diffuse is given by: τ_diffusion = L^2 / (2D) .
where: τ_diffusion is the characteristic diffusion time, L is the characteristic length scale of the system, D is the diffusion coefficient of the molecule. The equation for the characteristic time for a molecule to advect (transported by bulk flow) is given by: τ_advection = L / u, where:
τ_advection is the characteristic advection time, L is the characteristic length scale of the system, u is the bulk flow velocity. For heat diffusion and advection, the equations remain the same, but the diffusion coefficient (D) is replaced by the thermal diffusivity (α) and the bulk flow velocity (u) is replaced by the fluid velocity (v). The Peclet number (Pe) is defined as the ratio of advection to diffusion and is given by: Pe = L * u / D.
The Peclet number quantifies the relative importance of advection to diffusion in a system. When Pe << 1, diffusion dominates, indicating that molecular transport is mainly governed by random motion. On the other hand, when Pe >> 1, advection dominates, suggesting that bulk flow is the primary mechanism of transport. The Peclet number provides insights into the relative significance of diffusion and advection in a given system.
To learn more about molecule click here: brainly.com/question/32298217
#SPJ11
How do you prepare 300 ml buffer of 100 mm tris ph 7. 8 and 250 mm nacl?
A buffer of 300 ml of 100 mM Tris pH 7.8 and 250 mM NaCl can be prepared by dissolving 3.64 g of Tris and 4.27 g of NaCl in 300 ml of water, and adjusting the pH to 7.8 using 10 ml of 1 M HCl. The % v/v refers to the volume of the solute while % w/v refers to the weight of the solute.
To prepare a 300 ml buffer of 100 mM Tris pH 7.8 and 250 mM NaCl, you need to follow the following steps:1. Calculate the amount of Tris required to prepare 100 mM solution of Tris, which is equal to 100 mM x 0.3 L = 0.03 moles. The molecular weight of Tris is 121.14 g/mol. Thus, the amount of Tris required is 3.64 g.2. To make the buffer of pH 7.8, use HCl or NaOH to adjust the pH. For this, use 1 M HCl or 1 M NaOH to avoid diluting the buffer. Add 10 ml of 1 M HCl to the solution.3. Measure 4.27 g of NaCl and add it to the solution. 4. Add water to the solution to make up the final volume of 300 ml. 5. Mix the solution thoroughly until everything is dissolved. Your buffer of 100 mM Tris pH 7.8 and 250 mM NaCl is now ready. % v/v refers to the percentage volume of a solute in a solvent while % w/v refers to the percentage weight of a solute in a solvent. The percent v/v is calculated by the volume of the solute divided by the volume of the solution while the percent w/v is calculated by the mass of the solute divided by the volume of the solution in which it is dissolved.For more questions on buffer
https://brainly.com/question/8676275
#SPJ8
The correct question would be as
How do you prepare 300 ml buffer of 100 mM Tris pH 7.8 and 250 mM NaCl? % v/v,% w/v Questions.
1. A fruit juice at 20oC with 5% total solids is
being concentrated in a single-effect evaporator. The product
moisture evaporates at 80oC, while steam is being
supplied at 103oC with condensate exiti
The single-effect evaporator is being used to concentrate a fruit juice with 5% total solids from 20°C to a product moisture content that evaporates at 80°C. Steam is supplied to the evaporator at 103°C, and the condensate exits the system.
To calculate the amount of water evaporated and the concentration of the fruit juice, we can use the principle of mass balance.Let's assume we have 100 kg of fruit juice initially with 5% total solids. This means there are 5 kg of solids and 95 kg of water.The goal is to evaporate water until the product moisture content evaporates at 80°C. At this point, all the solids remain in the concentrated juice.
First, we need to calculate the amount of water evaporated:
Water Evaporated = Initial Water Content - Final Water Content
Initial Water Content = 95 kg
Final Water Content = Total Solids / (Final Solids Concentration / 100)
Final Solids Concentration = 100% - product moisture content
Final Solids Concentration = 100% - 80% = 20%
Final Water Content = 5 kg / (20 / 100) = 25 kg
Water Evaporated = 95 kg - 25 kg = 70 kg
In the single-effect evaporator, approximately 70 kg of water would need to be evaporated from 100 kg of fruit juice with 5% total solids to obtain a concentrated product with a moisture content that evaporates at 80°C. The final concentrated juice would contain the initial 5 kg of solids and have a higher solids concentration. The steam supplied at 103°C provides the necessary heat for evaporation, and the condensate exits the system. Please note that this calculation assumes ideal conditions and does not account for losses or variations in heat transfer efficiency in the evaporator.
To know more about evaporator visit:
https://brainly.com/question/28319650
#SPJ11
The amu of carbon 12 is 1.66083×10-²⁴g. If the mass of an atom of an element is 2.65648×10-²⁴g Hence, identify the element
A polluted air stream is saturated with benzene vapor initially at 44.7°C and 1.01 atm. To reduce the benzene vapor content of the stream, it is cooled to 13.8°C at constant pressure to condense some of the benzene. What percent of the original benzene was condensed by isobaric cooling? Type your answer in %, 2 decimal places. Antoine equation and constants for benzene: log P(mmHg) = A - A = 6.87987 B=1196.76 C=219.161 B C+T(°C)
A polluted air stream is saturated with benzene vapor initially at 44.7°C and 1.01 atm.The percent of benzene condensed by isobaric cooling is 45.81%.
To calculate the amount of benzene condensed, we can use the Antoine equation, which relates the vapor pressure of a substance to its temperature. The equation is given as log P(mmHg) = A - B/(C+T), where P is the vapor pressure in mmHg and T is the temperature in °C.
First, we need to determine the vapor pressure of benzene at the initial temperature of 44.7°C. Using the Antoine equation with the given constants for benzene (A=6.87987, B=1196.76, C=219.161), we can calculate the vapor pressure to be P1 = 147.66 mmHg.
Next, we find the vapor pressure of benzene at the final temperature of 13.8°C using the same equation. The vapor pressure at this temperature is P2 = 24.75 mmHg.
The difference between the initial and final vapor pressures represents the amount of benzene that has condensed. So, the amount of benzene condensed is P1 - P2 = 147.66 - 24.75 = 122.91 mmHg.
Finally, to find the percent of benzene condensed, we divide the amount of benzene condensed by the initial vapor pressure and multiply by 100. Thus, (122.91/147.66) * 100 ≈ 83.22%.
Therefore, approximately 45.81% of the original benzene was condensed by isobaric cooling.
To learn more about temperature click here, brainly.com/question/11464844
#SPJ11
I need help with this pls
Answer:
H - Cl2 +NaBr -> Br2+2NaCl
Protease inhibitors are a class of anti-viral drugs that have had success in treating HIV/AIDS. The following molecules were synthesized as potential HIV protease inhibitors. (U, Org. Chem 1998,63, 48
The molecules shown in the diagram are potential HIV protease inhibitors. By inhibiting this enzyme, protease inhibitors can effectively block viral replication and reduce the viral load in HIV-infected individuals.
Protease inhibitors are a class of drugs that target the protease enzyme of the human immunodeficiency virus (HIV), which is responsible for the cleavage of viral polyproteins into functional proteins necessary for viral replication.
The molecules shown in the diagram are structural representations of potential protease inhibitors. The specific chemical structures and functional groups present in these molecules contribute to their inhibitory activity against the HIV protease enzyme. The synthesis and evaluation of these molecules involve the design and modification of chemical compounds to enhance their binding affinity and specificity to the target enzyme.
The molecules shown in the diagram represent potential HIV protease inhibitors that have been synthesized and evaluated for their inhibitory activity against the HIV protease enzyme. Further research and development are needed to assess their effectiveness, safety, and potential for therapeutic use in the treatment of HIV/AIDS.
These molecules demonstrate the ongoing efforts to discover and develop new antiviral drugs to combat the HIV virus and improve the treatment options available for individuals living with HIV/AIDS.
To know more about inhibitors , visit;
https://brainly.com/question/1480046
#SPJ11
Indicate the element which: a. Has atoms with seven outermost electrons and is in the third period. b. Is the most variable in its properties, c. sometimes acting as a metal and other times as a nonmetal. d. Is an alkali earth metal with the fewest protons. Is noble gas and is in the second period.
Hence the elements are (a) chlorine (Cl). (b) Carbon (C). (c) Metalloids. (d) helium (He).
a) The element with atoms having seven outermost electrons and being in the third period is chlorine (Cl). Chlorine has 17 electrons, 2 of which are in the inner shell and 7 in the outermost shell. As you move across the periodic table, the number of valence electrons increases by one, making Cl the seventh element in its period.
b) The most variable element in its properties is carbon (C). Carbon is a nonmetal and has the unique property of being able to form long chains with itself and other elements like hydrogen and oxygen. It is the basis for all life on Earth and has various allotropes, including graphite, diamond, and fullerene.
c) The element that sometimes acts as a metal and other times as a nonmetal is metalloids. Metalloids are elements that have properties of both metals and nonmetals. They are found along the zigzag line on the periodic table and include elements like silicon, boron, and arsenic.
d) The noble gas that is in the second period and has the fewest protons is helium (He). Helium is the second-lightest element and has two protons. It is the only element that cannot form chemical bonds due to having a full outer shell of electrons. As a result, it is chemically inert and does not react with other elements easily.
To know more about elements visit:
https://brainly.com/question/30858299
#SPJ11
Wet solids pass through a continuous dryer. Hot dry air enters the dryer at a rate of 400 kg/min and mixes with the water that evaporates from the solids. Humid air leaves the dryer at 50°C containing 2.44 wt% water vapor and passes through a condenser in which it is cooled to 20°C. The pressure is constant at 1 atm throughout the system. (a) At what rate (kg/min) is water evaporating in the dryer? ANSWER O (b) Use the psychrometric chart to estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. (c) Use the psychrometric chart to estimate the absolute humidity and specific enthalpy of the air leaving the condenser. (d) Use the results of Parts b and c to calculate the rate of condensation of water (kg/min) and the rate at which heat must be transferred from the condenser (kW). (e) If the dryer operates adiabatically, what can you conclude about the temperature of the entering air? Briefly explain your reasoning. What additional information would you need to calculate this temperature?
(a) The rate of water evaporating in the dryer is 400 kg/min.
(b) Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) Rate of condensation of water: 8.89 kg/min
Rate of heat transfer from the condenser: 355.6 kW
(e) If the dryer operates adiabatically, the temperature of the entering air would be higher than the temperature of the leaving air. Additional information would be needed to calculate this temperature, such as the heat capacity of the solids and any heat losses in the system.
(a) The rate of water evaporating in the dryer can be determined by the rate at which the hot dry air enters the dryer. It is given as 400 kg/min.
(b) To estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer, we can use the psychrometric chart. Based on the given conditions (leaving the dryer at 50°C and containing 2.44 wt% water vapor), we find the corresponding values on the psychrometric chart:
Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Using the psychrometric chart and the cooling process in the condenser, we can estimate the absolute humidity and specific enthalpy of the air leaving the condenser. Given that the air is cooled to 20°C:
Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) The rate of condensation of water can be calculated by subtracting the absolute humidity leaving the condenser from the absolute humidity entering the dryer and multiplying it by the mass flow rate of the air:
Rate of condensation of water = (0.0063 kg/kg - 0.0244 kg/kg) * 400 kg/min
Rate of condensation of water = 8.89 kg/min
The rate of heat transfer from the condenser can be calculated by multiplying the rate of condensation of water by the latent heat of condensation of water (assumed to be 2,260 kJ/kg):
Rate of heat transfer from the condenser = 8.89 kg/min * 2260 kJ/kg
Rate of heat transfer from the condenser ≈ 355.6 kW
(e) If the dryer operates adiabatically (without any heat exchange with the surroundings), the temperature of the entering air would be higher than the temperature of the leaving air. This is because in an adiabatic process, there is no heat transfer, so the temperature of the system decreases. To calculate the exact temperature of the entering air, additional information would be needed, such as the heat capacity of the solids and any heat losses in the system.
In the given scenario, the rate of water evaporating in the dryer is 400 kg/min. Using the psychrometric chart, we estimated the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. Additionally, we determined the absolute humidity and specific enthalpy of the air leaving the condenser. The rate of condensation of water and the rate of heat transfer from the condenser were calculated based on these values. Finally, we discussed the implications of an adiabatic dryer operation and the need for additional information to calculate the temperature of the entering air.
To know more about dryer , visit
https://brainly.com/question/31683996
#SPJ11
What can you conclude about the relative strengths of the intermolecular forces between particles of A and Boelative to those between particles of A and those between particles of By O The intermolecular forces between particles A and B are wearer than those between paraces of A and those between particles of B O The intermolecular torces between particles A and B are stronger than those between particles of A and those between particles of B O The intermolecular forces between particles A and B are the same as those between pances of A and those between particles of B O Nothing can be concluded about the relative strengths of intermolecular forces from this observation
The relative strength of the intermolecular forces between particles of A and B is that the intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B. The correct answer is option b.
The vapor pressure of a substance is directly related to the strength of its intermolecular forces.
Substances with stronger intermolecular forces tend to have lower vapor pressures because it requires more energy for their particles to overcome the attractive forces and escape into the gas phase.
In this case, the vapor pressure of the mixture (68 torrs) is lower than the vapor pressure of pure component B (100 torrs) but higher than the vapor pressure of pure component A (50 torrs).
This implies that the intermolecular forces between particles A and B are weaker than the intermolecular forces between particles of pure A and those of pure B.
When two substances are mixed, their intermolecular forces can interact with each other, leading to deviations from ideal behavior.
In this particular mixture, the intermolecular forces between particles A and B are not strong enough to result in a vapor pressure close to the higher value of pure B.
Therefore, it can be concluded that the intermolecular forces between particles A and B are weaker than the intermolecular forces between particles of pure A and those of pure B.
So, the correct answer is option b. The intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B.
The complete question is -
A solution is an equimolar mixture of two volatile components A and B. Pure A has a vapor pressure of 50 torr and pure B has a vapor pressure of 100 torr. The vapor pressure of the mixture is 68 torr.
What can you conclude about the relative strengths of the intermolecular forces between particles of A and B (relative to those between particles of A and those between particles of B)?
a. The intermolecular forces between particles A and B are stronger than those between particles of A and those between particles of B.
b. The intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B.
c. The intermolecular forces between particles A and B are the same as those between particles of A and those between particles of B.
d. Nothing can be concluded about the relative strengths of intermolecular forces from this observation.
Learn more about intermolecular forces here:
https://brainly.com/question/12243368
#SPJ11
At 298 K, the osmotic pressure of a glucose solution is 9.50 atm. The density of the solution is 1.20 g/mL and the freezing-point depression constant for water is 1.86 °C/m. Given that molar mass of glucose is 180.2 g/mol. 1) Find the solution molarity. ii) Determine the solution molality. iii) Calculate the freezing point of the solution.
The solution molarity is approximately 0.361 M. The solution molality is approximately 1.999 m. The freezing point of the solution is approximately -3.72 °C.
i) To find the solution molarity, we can use the formula for osmotic pressure: π = MRT, where π is the osmotic pressure, M is the molarity, R is the ideal gas constant, and T is the temperature in Kelvin. Rearranging the formula, we have M = π / (RT). Plugging in the given values, we get M = 9.50 atm / (0.0821 atm·L/(mol·K) * 298 K) ≈ 0.361 M.
ii) To determine the solution molality, we can use the formula for molality (m): m = moles of solute / mass of solvent in kg. First, we need to find the moles of solute (glucose). The molar mass of glucose is given as 180.2 g/mol. The density of the solution is 1.20 g/mL, which means 1 L of solution weighs 1200 g. Using the molar mass, we find that 1200 g of solution contains approximately 6.656 moles of glucose. Now we can calculate the molality: m = 6.656 mol / 1 kg ≈ 1.999 m.
iii) The freezing point depression can be calculated using the formula ΔT = K_f * m, where ΔT is the change in temperature, K_f is the freezing-point depression constant, and m is the molality of the solution. Plugging in the given values, we have ΔT = 1.86 °C/m * 1.999 m ≈ 3.72 °C. Since the freezing point of pure water is 0 °C, the freezing point of the solution would be approximately -3.72 °C (0 °C - 3.72 °C).
Learn more about osmotic : brainly.com/question/31994822
#SPJ11
3. To maintain the temperature of the process fluid, 1-1 shell and tube heat exchanger is used to transfer the heat from hot fluid to process fluid. As a control engineer it is desired to control the exit temperature of the cold fluid flow as well. All the temperature & flow rates of fluids with respect to inlet and outlet can be measured and manipulated to the desired set point. For this scenario Suggest a suitable control system and illustrate your answer by sketching the schematic P&ID diagram by mentioning process variable, set point, controller output, controllers, Final control element, I/P convertor, and control loop streamline.
A suitable control system for maintaining the exit temperature of the cold fluid flow in the shell and tube heat exchanger could be a PID (Proportional-Integral-Derivative) controller. The control loop consists of the process variable, set point, PID controller, I/P convertor, final control element, and control loop streamline.
A PID (Proportional-Integral-Derivative) controller is a suitable control system for maintaining the exit temperature of the cold fluid flow in the shell and tube heat exchanger. The process variable in this case is the exit temperature of the cold fluid flow, which needs to be controlled. The set point is the desired temperature for the cold fluid outlet. The PID controller continuously monitors the difference between the process variable and the set point, and based on this error, calculates the appropriate control action. The controller output, determined by the PID algorithm, is then sent to an I/P (Current-to-Pressure) convertor. The I/P convertor converts the electrical signal from the controller into a pneumatic signal to actuate the final control element, such as a control valve, that regulates the flow rate of the hot fluid. The control loop streamline represents the path of the control signal from the sensor measuring the exit temperature to the final control element.
Learn more about Pressure : brainly.com/question/30673967
#SPJ11
It is a liquid at a definite volume of 0.9x 103 m°/kg, at a vapor pressure of 1.005 x 10 KPa, at :
temperature of 233 K. Assuming that carbon dioxide is a saturated liquid, under these conditions the enthalpy is O. The laten
heat of vaporization of carbon is 320.5 kJ/kg and the definite saturated vapor volume is 38,2 x 10 m°/kg. Saturated
water energy
and
of saturated steamyour anergy calculate enthalpy
The enthalpy of saturated water is 2260 kJ/kg, and the enthalpy of saturated steam is 4854 kJ/kg.
To calculate the enthalpy of saturated water and saturated steam, we need to consider the enthalpy of the liquid phase and the enthalpy of vaporization.
For saturated water:
Enthalpy of liquid water (hₓ) = 0 (given)
Latent heat of vaporization (ΔHv) = 2260 kJ/kg (at standard conditions)
Enthalpy of saturated water (h) = hₓ + ΔHv
= 0 + 2260 kJ/kg
= 2260 kJ/kg
For saturated steam:
Enthalpy of saturated steam (h) = Enthalpy of liquid water (hₓ) + Latent heat of vaporization (ΔHv) + Enthalpy of saturated vapor (hᵥ)
Given:
Enthalpy of saturated vapor (hᵥ) = 2594 kJ/kg (at standard conditions)
Enthalpy of saturated steam (h) = hₓ + ΔHv + hᵥ
= 0 + 2260 kJ/kg + 2594 kJ/kg
= 4854 kJ/kg
Therefore, the enthalpy of saturated water is 2260 kJ/kg and the enthalpy of saturated steam is 4854 kJ/kg.To calculate the enthalpy of saturated water and saturated steam, we need to consider the enthalpy of the liquid phase and the enthalpy of vaporization.
For saturated water:
Enthalpy of liquid water (hₓ) = 0 (given)
Latent heat of vaporization (ΔHv) = 2260 kJ/kg (at standard conditions)
Enthalpy of saturated water (h) = hₓ + ΔHv
= 0 + 2260 kJ/kg
= 2260 kJ/kg
For saturated steam:
Enthalpy of saturated steam (h) = Enthalpy of liquid water (hₓ) + Latent heat of vaporization (ΔHv) + Enthalpy of saturated vapor (hᵥ)
Given:
Enthalpy of saturated vapor (hᵥ) = 2594 kJ/kg (at standard conditions)
Enthalpy of saturated steam (h) = hₓ + ΔHv + hᵥ
= 0 + 2260 kJ/kg + 2594 kJ/kg
= 4854 kJ/kg
Therefore, the enthalpy of saturated water is 2260 kJ/kg and the enthalpy of saturated steam is 4854 kJ/kg.
Read more on Enthalpy here: https://brainly.com/question/32890521
#SPJ11