refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.14 mpa, and leaves as superheated vapor at 0.8 mpa and 608c at a rate of 0.06 kg/s. determine the rates of energy

Answers

Answer 1

The rate of energy that refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.14 mpa, and leaves as superheated vapor at 0.8 mpa and 608c at a rate of 0.06 kg/s is thus 24.072 kJ/s.

First, we need to calculate the enthalpy of saturated vapor at 0.14 mpa. This can be found in a vapor table. The enthalpy of saturated vapor at 0.14 mpa is 272.6 kJ/kg. Next, we need to calculate the enthalpy of superheated vapor at 0.8 mpa and 608C. Again, this can be found in a vapor table. The enthalpy of superheated vapor at 0.8 mpa and 608C is 681.2 kJ/kg.

Now, we can calculate the rate of energy that refrigerant-134a enters the compressor of a refrigeration system. We calculate this by subtracting the enthalpy of saturated vapor (272.6 kJ/kg) from the enthalpy of superheated vapor (681.2 kJ/kg) and multiplying the difference by the rate of flow (0.06 kg/s). The rate of energy that refrigerant-134a enters the compressor of a refrigeration system is thus 24.072 kJ/s.

You can learn more about refrigeration systems at: brainly.com/question/29910871

#SPJ11


Related Questions

_______ is the movement of electrons from one atom to another.
A/an _______ is a unit of the amount of current flow.
A/an _______ is a unit of electrical pressure.
A/an _______ involves a copper-to-copper connection whereas a short-to-round involves a copper-to-steel connection.
_______ law states, “The current flowing into any junction of an electrical circuit is equal to the current flowing out of that junction.”
If 12 volts are being applied to a resistance of 3 ohms, _______ amperes will flow.
If the voltage increases in a circuit and the resistance remains the same, the current _______.
The sum of the voltage drops in a series circuit equals the _______.
If the resistance and the voltage are known, the formula for finding the current is _______.

Answers

Electricity is the movement of electrons between atoms.

   

The atomic structure

The atomic mass or atomic weight is the total mass of an atom, including protons, neutrons, and electrons. Atomic mass units are used to measure atomic mass or weight. Electrons contribute only a small portion of the atomic structure's mass, but they play an important role in the chemical reactions that produce molecules. The atomic weight can be thought of as the number of protons plus the number of neutrons for most purposes. Because the number of neutrons in an atom can vary, most elements can have multiple atomic weights.The charges of protons and electrons are equal and opposite. Protons are positively charged, while electrons are negatively charged. Normally, atoms have an equal number of protons and neutrons.  

To know more about Atom, click on the link :

https://brainly.com/question/30898688

#SPJ1

what is the transfer function? what is the steady-state error, ess? what is the natural frequency? you can assume ra

Answers

The transfer function is a mathematical representation of the relationship between the input and the output of a system. The steady-state error, or ess, is the difference between the desired output and the actual output when the system reaches a steady state. The natural frequency is the frequency of the system's response without any external forces.

Transfer Function: Transfer Function is used in signal processing, control engineering, and other disciplines that deal with systems or signals. The ratio of output to input in Laplace transform is known as the transfer function.

Steady-State Error: The error that happens when the system is at a stable state is referred to as a steady-state error. The difference between the desired and actual response is known as steady-state error. A system's ability to track a specific input as time progresses is characterized by this kind of error. If the input signal is a unit step, then the steady-state error is referred to as the static error coefficient. The coefficient of the steady-state error is frequently used to classify systems in control engineering.

Natural Frequency: Natural frequency is a term used in physics to describe how quickly an object vibrates when it is set in motion. The number of oscillations made by a system in a given time period without any external force acting on it is referred to as its natural frequency. A natural frequency is a measure of a system's stiffness and mass. In a control system, it is the frequency at which the system oscillates in the absence of any input.

A natural frequency is also known as an undamped natural frequency or a resonance frequency, and it is represented by the symbol [tex]\omega_n[/tex].You can assume the following in the problem. If you have any specific values, kindly provide them.

Learn more about Transfer Function here:

https://brainly.com/question/24241688

#SPJ11

What is the difference between geomatics and land surveying

Answers

Land surveying is the era used to gather records additionally a part of geomatics. but geomatics is a technology to discover ways to analysis that survey geospatial facts through diverse approach and making out a selection via it.



Land Surveying (or Engineering Surveying) is in truth a sub-area of Geomatics. however, in practice, there may be little to no distinction between the disciplines and the phrases get used interchangeably often.
A Geomatics engineer will employ sensors, knowledge and software to provide notably correct positional information for any of these scenarios.
Surveyors make specific measurements to decide belongings boundaries. They provide information applicable to the form and contour of the Earth's floor for engineering, mapmaking, and creation initiatives.

To know more about land surveying click on right here
brainly.com/question/29841451
#SPJ4

what is the ratio of the induced emf in the loop cdbc to the induced emf in the loop cadc; i.e., what is ecdbc ecadc ?

Answers

The ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:

ecdbc/ecadc = -dΦ_cdbc/dt / (-dΦ_cadc/dt) = dΦ_cadc/dt / dΦ_cdbc/dt

Let's dive deeper into the details below

The induced EMF is the voltage generated by a changing magnetic field in a coil of wire. In a loop, the induced EMF is proportional to the rate of change of the magnetic flux that is threading the loop. Therefore, in a loop, the induced EMF can be calculated as:

induced EMF = -dΦ/dt, where Φ is the magnetic flux threading the loop.

We can assume that both loops are parallel to the surface and therefore perpendicular to the magnetic field. This means that the magnetic flux threading each loop is proportional to the area of the loop, as follows:

Φ_cadc = B A_cadc and Φ_cdbc = B A_cdbc

Therefore, the ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:

ecdbc/ecadc = dΦ_cadc/dt / dΦ_cdbc/dt = (B A_cadc)/dt / (B A_cdbc)/dt = A_cadc / A_cdbc

The answer is the ratio of the areas of the loops.

Learn more about magnetic flux.

brainly.com/question/30858765

#SPJ11

which type of sprinkler system allows immediate and simultaneous discharge of all sprinkler heads? dry-pipe system deluge system pre-action system wet-pipe system

Answers

The type of sprinkler system that allows immediate and simultaneous discharge of all sprinkler heads is the deluge system.

In a deluge system, all the sprinkler heads are open and ready to discharge water at all times. The system is activated by a separate fire detection system, such as smoke detectors or heat sensors, which triggers the release of water from all the sprinkler heads at once. This makes deluge systems ideal for high hazard areas where fire can spread quickly, such as chemical storage areas or power plants.

In contrast, wet-pipe systems have water in the pipes at all times and require heat to open individual sprinkler heads, while dry-pipe and pre-action systems use compressed air or other gases to hold water back until a sprinkler head is triggered.

To learn more about sprinkler system refer to:

brainly.com/question/28992367

#SPJ4

The XYZ Company is planning a new product line and a new factory to produce the parts and assemble the final products. The product line will include 13 different models. Annual production of each model is expected to be 1,000 units. Each product will be assembled of 250 components, but 65% of these will be purchased parts (not made in the new factory). There is an average of 8 processing operations required to produce each component, and each processing step takes 30 sec (including an allowance for setup time and part handling). Each final unit of product takes 48 min to assemble. All processing operations are performed at work cells that include a production machine and a human worker. Products are assembled at single workstations consisting of one worker each plus assembly fixtures and tooling. Each work cell and each workstation require 25 m2 of floor space and an additional allowance of 45% must be added to the total production area for aisles, work-in-process storage, shipping and receiving, rest rooms, and other utility space. The factory will operate one shift (the day shift, 2,000 hr/yr). Determine: (a) how many processing and assembly operations, (b) how many workers (direct labor only), and (c) how much total floor space will be required in the plant.

Answers

The plant will need to perform 9,100,000 processing and assembly procedures altogether.

What fundamental processing tasks are carried out in a manufacturing facility?

Shape operations, property-enhancing operations, and surface processing operations are the three distinct categories of processing operations. By using mechanical force, heat, or other forms and combinations of energy, shaping operations change the work material's geometry.

There are 250 components in each product.

Parts purchased as a percentage equal 65%.

250 - (65% x 250) = 87.5 is the number of components that will be produced in the new facility.

Eight processing steps are needed to manufacture each component.

The new factory's processing procedures per component totaled 8 x 87.5, or 700.

13 x 1000 x (700 + 1) = 9,100,000 is the total number of processing and assembly procedures needed for the 13 different models.

To know more about assembly visit:-

https://brainly.com/question/13557244

#SPJ1

snow and ice heavily damages a building that was designed by registered engineers and architects. the owner was not able to recover damages because of:

Answers

The owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the engineers and architects had specified the use of materials or building techniques that are not designed to handle those types of conditions.

Additionally, the owner may not have taken proper preventative measures to ensure the building was properly insulated and protected from the weather, or the owner may not have maintained the building appropriately. Finally, the owner may not have been able to prove negligence on the part of the engineers or architects in the building's design or construction.

In conclusion, the owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the building was not designed to withstand such conditions, if the owner failed to take proper preventative measures to protect the building, or if the owner could not prove negligence on the part of the engineers and architects.

You can learn more about building design at: brainly.com/question/8741590

#SPJ11

explain the modulus of elasticity. which property of the material does it represent? give the approximate values of the modulus of elasticity of steel, concrete, and wood.

Answers

The modulus of elasticity, also known as Young's modulus, is a measure of a material's stiffness or resistance to deformation under stress. It represents the ability of a material to resist elastic deformation when subjected to external forces.

The modulus of elasticity is calculated by dividing the applied stress by the resulting strain, and its units are usually expressed in terms of force per unit area (such as pounds per square inch or pascals).

Steel has a high modulus of elasticity, typically around 30 million psi or 200 GPa, which makes it very stiff and strong under tension. Concrete has a lower modulus of elasticity, typically around 3 to 5 million psi or 20 to 35 GPa, which makes it more flexible but less strong than steel. Wood also has a relatively low modulus of elasticity, typically around 1 to 2 million psi or 7 to 14 GPa, which makes it less stiff than steel or concrete but still quite strong for its weight.

To learn more about Young's modulus refer to:

brainly.com/question/13257353

#SPJ4

technician a says that brake fluid that is allowed to remain uncovered absorbs water. technician b says that if brake fluid is accidentally spilled on a fender of a vehicle, it can damage the paint. who is correct?

Answers

Technician A and Technician B both are correct as brake fluid that is allowed to remain uncovered does absorb water and brake fluid can damage the paint on a vehicle's fender if it is accidentally spilled.

Technician A is correct because brake fluid is hygroscopic, which means it absorbs moisture from the atmosphere. This water can corrode brake parts and lead to failure, as well as increase the fluid's boiling point, leading to brake fade and reduced stopping power.
Technician B is also correct because brake fluid is made up of corrosive materials that can break down paint and other surfaces. If the brake fluid is not cleaned off the fender immediately, it can cause permanent damage to the paint.

You can learn more about corrosive materials at: brainly.com/question/29632416

#SPJ11

for materials such as aluminum, glass, steel, and concrete, the value of the coefficient of volume expansion is approximately how many times larger than the coefficient of linear expansion?

Answers

The coefficient of volume expansion and the coefficient of linear expansion are both thermal properties of a material that describe how its dimensions change in response to changes in temperature.

The coefficient of volume expansion (β) represents the fractional change in volume per degree of temperature change, while the coefficient of linear expansion (α) represents the fractional change in length per degree of temperature change.

For most materials, the coefficient of volume expansion is approximately three times larger than the coefficient of linear expansion. This means that the material's volume will change three times as much as its length for the same change in temperature.

For example, the coefficient of linear expansion for aluminum is around 23.1 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 69 × 10⁻⁶ /°C. Similarly, the coefficient of linear expansion for glass is around 8 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 24 × 10⁻⁶ /°C. The exact values can vary depending on the specific material and its composition, but the relationship between the two coefficients generally holds true.

To learn more about linear expansion refer to:

brainly.com/question/14780533

#SPJ4

why must you consider output impedance of signal conditioning circuit or input impedance of measuring device

Answers

It is important to consider the output impedance of a signal conditioning circuit and the input impedance of the measuring device for several reasons. First, the signal conditioner’s output impedance will affect the amplitude and frequency response of the signal as it is sent to the measurement device.

1) If the impedance of the signal conditioner and the measuring device don't match, it can lead to incorrect readings.

2) Secondly, the signal conditioner’s output impedance also affects the signal-to-noise ratio, which can influence the quality of the measurements taken.

3) Lastly, the input impedance of the measuring device must match the output impedance of the signal conditioning circuit in order to ensure a low-distortion signal that accurately reflects the original signal.

In summary, it is important to consider the output impedance of the signal conditioning circuit and the input impedance of the measuring device in order to ensure accurate and high-quality measurements.

It is important to consider the output impedance of a signal conditioning circuit or the input impedance of a measuring device for optimal performance and accurate measurements. This is because the impedance values affect the signal transfer between the circuit and the device.

The input impedance of a measuring device refers to the resistance of the device input to the output impedance of the signal conditioning circuit.

If the input impedance of the device is too low, it can lead to a large current flowing from the circuit to the device, which can cause distortion and reduce the accuracy of the measurement.

On the other hand, if the input impedance is too high, it can affect the signal transfer between the circuit and the device, leading to a loss of signal strength and distortion.

For more such questions on impedance

https://brainly.com/question/29853108

#SPJ11

Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers _______________.
A) are more accountable for what students learn
B) have students with a wider variety of learning needs
C) have more special students placed in their regular classrooms

Answers

Option B. In the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs.

According to Dewey, curriculum and institutions should be secondary to children in brain-based pedagogy since learning is socially produced. Students have to apply prior knowledge to generate new meaning in order to effectively learn.

This is what makes individualized instruction complex.Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs. Student-centered learning, on the other hand, has been a popular idea in education for years.

The popularity of student-centered learning can be traced back to John Dewey, a prominent educational philosopher. In Dewey's view, student-centered learning focused on the student's experience, interests, and interaction with the environment. Therefore the correct option is B.

Learn more about "teachers" at: https://brainly.com/question/28328532

#SPJ11

Truss ABC is changed by decreasing its height from H to 0.9 H. Width W and load P are kept the same. Which one of the following statements is true for the revised truss as compared to the original truss?
A. Force in all its members have decreased.
B. Force in all its members have increased.
C. Force in all its members have remained the same.
D. None of the above.

Answers

Force in all its members have increased

Force Equation

The vector product of mass (m) and acceleration (a) expresses the quantity of force (a). The force equation or formula can be expressed mathematically as follows:

F = ma In which case,

m = mass a = velocity

It is expressed in Newtons (N) or kilogrammes per second.

The acceleration an is provided by

a = v/t

Where

v = acceleration

t = time spent

As a result, Force can be expressed as follows:

F = mv/t

The formula for inertia is p = mv, which can also be expressed as Momentum.

As a result, force can be defined as the rate of change of momentum.

dp/dt = F = p/t

Force formulas are useful for determining the force, mass, acceleration, momentum, and velocity in any given problem.

To know more about Force,click on the link :

https://brainly.com/question/13191643

#SPJ1

this is a longitudinal section through the end of a finger. what is the correct name for the area circled in this virtual slide specimen?

Answers

The longitudinal segment through the end of a finger in this virtual slide specimen is known as Hyponychium the tissue located underneath the nail plate.

The hyponychium is the area of skin beneath the free edge of the nail plate, at the distal end of the finger or toe. It is sometimes referred to as the "quick" or the "nail bed seal,"

The hyponychium is an important part of the nail unit and is composed of specialized skin cells that help to support and protect the nail.

The hyponychium plays an important role in protecting the underlying nail bed and fingertip from damage, infection, and other types of trauma. Here are some of the benefits of the hyponychium:

1) Protection: The hyponychium acts as a barrier between the nail bed and the environment, protecting the underlying tissue from injury and infection.

2) Seal: The hyponychium seals the area between the nail plate and the nail bed, preventing dirt, debris, and bacteria from getting underneath the nail and causing infection.

3) Sensation: The hyponychium contains nerve endings that provide sensory feedback to the brain, allowing us to feel pressure, touch, and other sensations

For more such questions on finger

https://brainly.com/question/29891515

#SPJ11

Note- The correct question would be as below

This is a longitudinal section through the end of a finger. What is the correct name for the area circled in this virtual slide specimen?

A stone with a mass of 0.600 kg is attached to one end of a string 0.800 m long. The string will break if its tension exceeds 55.0 N. The stone is whirled in a horizontal circle on a frictionless tabletop; the other end of the string remains fixed. Find the maximum speed the stone can attain without breaking the string.

Answers

To find the maximum speed the stone can attain without breaking the string, we need to determine the maximum tension the string can withstand.

We know that the tension in the string is equal to the centripetal force required to keep the stone moving in a circular path:

Tension = centripetal force = (mass x velocity^2) / radius

where the radius is the length of the string, 0.800 m.

If we rearrange the equation to solve for velocity, we get:

velocity = sqrt((Tension x radius) / mass)

Now we can substitute the given values:

Tension = 55.0 N (the maximum tension the string can withstand)
radius = 0.800 m
mass = 0.600 kg

Plugging these values into the equation, we get:

velocity = sqrt((55.0 N x 0.800 m) / 0.600 kg)
velocity = 3.31 m/s

Therefore, the maximum speed the stone can attain without breaking the string is 3.31 m/s.

Determine the gauge of the wire needed in circuits that specify power source, wire length, amps, and maximum volt drop.

Part I
Locate the wire-size engineering reference table (Chart 44-2) of your textbook to determine wire gauge when the diameter of the wire is known.

Use the table to determine the wire gauge for each wire diameter shown below. You may need to round the numbers to obtain the correct answer.
d = 2576 inch
d = 0.03196 inch
d = 0.0100 inch
d = 0.1285 inch
d = 0.0508 inch
Using the answers you just obtained, place the wire sizes in order from the smallest gauge to the largest.
Remember: The smaller the wire gauge, the larger the diameter of the wire.

Part II
Using what you’ve learned in Part I and the directions below, determine the recommended wire gauge for the following circuits:

Circuit A. Starter circuit using 5 feet of wire, with a 12 V power supply, and a current of 200 Amps.
Circuit B. Dome light circuit using 14 feet of wire, with a 12 V power supply, and a current of 10 Amps.
Circuit C. A/C blower circuit using 24 feet of wire, with a 14.6 V power supply, and a current of 18 Amps.
Use Ohm’s law (E = IR) to determine the resistance in the wire for each circuit. Remember, Volts = E, and the given current = I. (You can refer back to page 433 in your textbook to find the exact formula you’ll need to use.)
Circuit A: R =
Circuit B: R =
Circuit C: R =
The relationship between the resistance and the circuit’s wire is shown in this formula:

R=4ρπ(Id2)
To determine the diameter of the wire needed for each circuit when you know the resistance and wire length, you would use this formula:

R=4ρπ(Id2) d=IR√×π4ρ
R = resistance

r = 250 ohm/inch

l = length of the wire (inches)

d = cross-sectional area of the wire (in2)

You should substitute the calculated value for R and the given values for r and l and find the value of d for each circuit. (Use π = 3.1416.)

For example, here’s an example for Circuit A:

d=IR√×π4ρ=5.24494×3.14161000=.064


Circuit A: d =
Circuit B: d =
Circuit C: d =
Now, look in the engineering reference table for standard American wire or metric gauges (on page 468 of your textbook) to determine the gauge of wire needed for the circuit.
Circuit A:
Circuit B:
Circuit C:

Answers

Answer:

See below.

Explanation:

Part I

Using Chart 44-2 in the textbook, we can determine the wire gauge for each given diameter

For d = 0.2576 inch, the wire gauge is 2 AWG.

For d = 0.03196 inch, the wire gauge is 20 AWG.

For d = 0.0100 inch, the wire gauge is 30 AWG.

For d = 0.1285 inch, the wire gauge is 8 AWG.

For d = 0.0508 inch, the wire gauge is 16 AWG.

Ordering the wire sizes from smallest to largest gauge, we have:

30 AWG < 20 AWG < 16 AWG < 8 AWG < 2 AWG

Part II

Circuit A

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 12/200 = 0.06 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(0.06/(42503.1416*200)) = 0.064 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit A is 2 AWG.

Circuit B

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 12/10 = 1.2 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(1.2/(42503.1416*10)) = 0.023 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit B is 14 AWG.

Circuit C

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 14.6/18 = 0.811 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(0.811/(42503.1416*18)) = 0.060 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit C is 4 AWG.

The input x(t) to a LTI system produces the output y(t)
x(t) = e^-t u(t)
y(t) = e^-3t u(t) Find the frequency response of the system, H(ω). Find the Impulse Response of the system, h(t). Find the differential equation for this system.

Answers

The frequency response of the system H(s) is (s + 1) / (s + 3) ,  the Impulse Response of the system h(t) is δ(t) - 2e^{(-3t)u(t)} and the differential equation for this system δ(t) is  h'(t) + 3h(t)

To find the frequency response of the system, H(ω), we can use the Laplace transform:

Y(s) = H(s)X(s)

where X(s) and Y(s) are the Laplace transforms of x(t) and y(t), respectively.

Taking the Laplace transform of x(t):

X(s) = 1 / (s + 1)

Taking the Laplace transform of y(t):

Y(s) = 1 / (s + 3)

Substituting these into the equation above:

H(s) = Y(s) / X(s) = (s + 1) / (s + 3)

To find the impulse response of the system, h(t), we can take the inverse Laplace transform of H(s):

h(t) = L^-1 {H(s)} = L^-1 {(s + 1) / (s + 3)}

Using partial fraction decomposition:

H(s) = (s + 1) / (s + 3) = 1 - 2/(s+3)

Taking the inverse Laplace transform:

h(t) = L^-1 {H(s)} = L^-1 {1} - L^-1 {2/(s+3)}

h(t) = δ(t) - 2e^{(-3t)}u(t)

where δ(t) is the Dirac delta function and u(t) is the unit step function.

To find the differential equation for the system, we can use the fact that the impulse response of an LTI system is the solution to the system's differential equation.

From the above, we have:

h(t) = δ(t) - 2e^(-3t)u(t)

Taking the derivative with respect to t:

dh(t)/dt = -3h(t) + δ'(t)

where δ'(t) is the derivative of the Dirac delta function.

Since δ(t) is zero everywhere except at t=0, its derivative is zero everywhere except at t=0 where it is infinite.

Thus, the differential equation for the system is:

dh(t)/dt + 3h(t) = δ(t)

or equivalently,

h'(t) + 3h(t) = δ(t)

where h'(t) is the derivative of h(t).

To practice more questions about differential equation:

https://brainly.com/question/30417555

#SPJ11

When E = 14 V and R = 1 Ω, the current is _________ amperes.
When E = 14 V and R = 4 Ω, the current is _________ amperes.
When E = 14 V and R = 8 Ω, the current is _________ amperes.
When E = 14 V and R = 12 Ω, the current is _________ amperes.

Answers

Answer:

When E = 14 V and R = 1 Ω, the current is 14 A.

When E = 14 V and R = 4 Ω, the current is 3.5 A.

When E = 14 V and R = 8 Ω, the current is 1.75 A.

When E = 14 V and R = 12 Ω, the current is 1.166... A
(rounded to three decimal places).

Explanation:

To calculate the current (I) using Ohm's law, we can use the formula:

I = E / R

where I is the current in amperes (A), E is the voltage in volts (V), and R is the resistance in ohms (Ω).

Answer:

Current = Emf / Resistance

When E = 14 V and R = 1 Ω, the current is 14/1 amperes = 14 amp

When E = 14 V and R = 4 Ω, the current is 14/4 amperes = 3.5 amp

When E = 14 V and R = 8 Ω, the current is 14 / 8 amperes = 1.75 amp

When E = 14 V and R = 12 Ω, the current is 14 / 12 amperes = 1.16 amp

You are travelling along a four lane highway. You see an emergency vehicle pulled over with its lights flashing ahead. Which of the following is true?A You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mphB You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 30 mphC You must come to a complete stop regardless of which direction you are travelling

Answers

You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mph is true.

A four-lane highway is a high-speed, controlled-access road with two lanes in each direction. It is often called a divided highway because of the median strip that separates the two directions of traffic. It is the most common type of multi-lane highway in the United States.

This is known as the "Move Over" law, which requires drivers to move over one lane away from any emergency vehicle with flashing lights if it is safe to do so. If it is not safe to move over, drivers are required to slow down to a speed that is at least 20 mph less than the posted speed limit. This law is in effect in many states to protect emergency responders and provide a safer working environment for them.

To learn more about speed-limit:

https://brainly.com/question/28488266

#SPJ11

the low-level wind shear alert system (llwas) provides wind data and software process to detect the presence of a

Answers

The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.

LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.

It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.

Learn more about LLWAS : https://brainly.com/question/30001468

#SPJ11

air enters a 28-cm diameter pipe steadily at 200 kpa and 208c with a velocity of 5 m/s. air is heated as it flows, and leaves the pipe at 180 kpa and 408c. determine (a) the volume flow rate of air at the inlet, (b)

Answers

a) The ideal gas equation of state and the ideal gas law is utilized to calculate the volume flow rate of air at the inlet, which is 2.73 cubic meters per second. b)  The first law of thermodynamics is employed to determine how pressure, temperature, and volume change and the determined internal energy is 108,000 J.

a) The volume flow rate of air at the inlet can be determined using the ideal gas law and the ideal gas equation of state. The equation is PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. Using the given values, we can determine the volume flow rate (V) to be 2.73 cubic meters per second.

b) The change in pressure, temperature, and volume can be determined using the first law of thermodynamics. The equation is ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat transferred, and W is the work done. Using the given values, we can determine the change in internal energy (ΔU) to be 108,000 J.

You can learn more about the ideal gas equation at: brainly.com/question/28837405

#SPJ11

why must the filter paper fit flat on the bottom the hirsch funnel and be wet before beginning collection of crystals?

Answers

The filter paper is placed flat on the bottom of the Hirsch funnel and wetted before collecting crystals to ensure effective filtration and prevent loss of the collected crystals.

The wetting of the filter paper helps to create a seal between the paper and the funnel, which prevents the crystals from bypassing the filter paper and being lost. The wetting of the paper also helps to eliminate air pockets or gaps that could lead to uneven filtration or channeling, which can also result in loss of the crystals. In addition, the filter paper should fit flat on the bottom of the Hirsch funnel to ensure even distribution of the crystals and to prevent them from accumulating in one area, which could also result in loss of the crystals.

Learn more about Hirsch funnel: https://brainly.com/question/30648758

#SPJ11

Service conductors passing over a roof shall be securely supported by substantial structures, and for a grounded system, where the substantial structure is ___, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor

Answers

The student question is: Service conductors passing over a roof shall be securely supported by substantial structures, and for a grounded system, where the substantial structure is ___, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor.

The answer to the blank is "metallic". So, for a grounded system, where the substantial structure is metallic, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor. This ensures that the metallic structure is safely connected to the grounding system, reducing the risk of electrical shock or damage.

To learn more about connected conductors : https://brainly.com/question/31274491

#SPJ11

Do you think test-driven development is a good idea? What might be a benefit of this approach? What might be a drawback?

Answers

Answer:

Test-driven development is a great idea for software development projects, as it helps ensure that the code is properly tested and written correctly. The benefit of this approach is that it allows for more accurate debugging and testing, resulting in fewer errors in the final product. The drawback is that it can be time consuming and expensive to implement, and may require additional resources to ensure that all tests are done properly.

3
Biocatalysis helps create flavors and scents through what process?
altering DNA

chemical reactions

purifying components in a formula

aiding with the decomposition process

Answers

Answer:

its B. ima keep it short its B

Explanation

what is the lowest possible frequency of an aliased signal if a 120 khz signal is sampled at 150 khz?

Answers

The lowest possible frequency of an aliased signal if a 120 kHz signal is sampled at 150 kHz is 30 kHz.

This is because the highest frequency component of a signal must be less than half the sampling frequency, or Nyquist Frequency. In this case, the Nyquist Frequency is 75 kHz, and 120 kHz is greater than 75 kHz, so it is aliased. The aliased frequency is equal to the difference between the sampling frequency and the highest frequency component, or 150 kHz - 120 kHz = 30 kHz.

Nyquist frequency is a type of sampling frequency used in signal processing which is defined as “half the rate” of a discrete signal processing system. This is the highest frequency that can be encoded for a given sampling rate so that the signal can be reconstructed.

Learn more about frequency : https://brainly.com/question/26146342

#SPJ11

3. Which product should be sprayed over an original OEM
finish before clearcoating?
A. Primer
B. Sealer
C. Adhesion promoter
D. Epoxy

Answers

Sealer should be sprayed over an original OEM finish before clearcoating. (Option B)

What is the explanation for the above response?

A sealer is a type of primer that is specifically designed to provide a smooth and uniform surface for the clearcoat to adhere to. It also helps to prevent any bleeding or discoloration from the original finish, and can improve the overall appearance of the final finish.

While primers and adhesion promoters can also be used in automotive painting, a sealer is the most appropriate product to use over an original OEM finish before clearcoating. Epoxy, on the other hand, is typically used as a primer for bare metal surfaces, rather than over an existing finish.

Learn more about OEM at:

https://brainly.com/question/17422536

#SPJ1

A 2500 kVA, 6600 V synchronous turbo alternator is operating at full load and 0.8 pf lagging. This machine has a synchronous reactance per phase is 10.4 ohms and a negligible resistance. Calculate the percent voltage regulation?

Answers

The percent voltage regulation of the synchronous turbo alternator is  0.0826%. This indicates the ability of the machine to maintain voltage output under different load conditions.

At full load, the apparent power output of the alternator is 2500 kVA. We can find the real power output by multiplying it by the power factor:

Real power = 2500 kVA x 0.8 = 2000 kW

The current drawn by the alternator can be calculated using the real power and voltage:

Current (I) = Real power (P) / Voltage (V) = 2000 kW / 6600 V = 0.303 A

The voltage drop in the synchronous reactance can be calculated using Ohm's Law:

Voltage drop = Current x Synchronous reactance per phase = 0.303 A x 10.4 ohms = 3.15 V

The percent voltage regulation can be calculated using the following formula:

Percent voltage regulation = (Voltage drop / No-load voltage) x 100

The no-load voltage of the alternator can be calculated using the synchronous EMF equation:

No-load voltage = Line voltage / Sq. root of 3

Line voltage = 6600 V

No-load voltage = 6600 V / Sq. root of 3 = 3814 V

Substituting the values:

Percent voltage regulation = (3.15 V / 3814 V) x 100 = 0.0826 %

Therefore, the percent voltage regulation of the synchronous turbo alternator is 0.0826%.

To practice more questions about voltage regulation:

https://brainly.com/question/14407917

#SPJ11

a measurement system can be modeled by the equation initially, the output signal is steady at 60 units. the input signal is then suddenly increased to 90 units. (a) determine the time constant and the sensitivity of the system.

Answers

The time constant of the system is not defined because the output signal remains at zero for all values of t. The sensitivity of the system is a = 0.

The time constant and sensitivity of a measurement system can be determined from the equation y = a (1 - e ^ -t/τ). Here, τ is the time constant and a is the sensitivity. The output signal is initially steady at 60 units and the input signal is then suddenly increased to 90 units.

The equation of the system is given by:

y = a (1 - e ^ -t/τ)

Given that the initial output signal is steady at 60 units, it implies that when t=0, y=60. Thus the equation becomes:

60 = a (1 - e ^ 0/τ)

60 = a (1 - 1)

60 = 0

This equation is not possible. It implies that the value of a is zero. Thus, the equation of the system is simplified to:

y = 0


Therefore, the answer  is a = 0.

Learn more about output signal : https://brainly.com/question/30953449

#SPJ11

concepts are general ideas you use to organize your experience and, in doing so, bring order and intelligibility to your life. t/f

Answers

The given statement "Concepts are general ideas that you use to organize your experience and, in doing so, bring order and intelligibility to your life. " is true because It is important to understand what concept is and how they are useful in our daily life as it helps us organize our experiences and ideas.

Concepts are general ideas that can be used to classify and organize information. They provide structure and coherence to our perceptions and experiences. When we have a concept, it helps us bring order to our experiences and gives us a framework for understanding new information.

By organizing information into categories, we can more easily remember, process, and communicate it. This can help us make sense of the world around us and navigate our experiences in a meaningful way. In conclusion, concepts are important because they help us make sense of our experiences and the world around us. They provide structure and intelligibility to our lives, allowing us to organize and communicate our ideas and experiences more effectively.

So the statement is true.

Learn more about "intelligibility" at: https://brainly.com/question/9944825

#SPJ11

Other Questions
Which side of the heart pumps blood to the lungs write a function named times ten. the function should accept an argument and display the product of its argument * 10. which networking model is based on peer-to-peer networking? answer workgroup client-server none standalone assume a bond's stated rate is 5% and the yield to maturity is 6%, will the bonds sell for par value, above par value, or below par value? creatinine clearance is used to assess the: group of answer choices tubular secretion of creatinine. glomerular and tubular mass. glomerular filtration capabilities of the kidneys. dietary intake of protein. How did Buddhism become a formal religion after the death of the Buddha? anyone with ability to affect others' thoughts or actions, especially purchasing decisions the project master network is a high-level plan that indicates a few significant accomplishments that are anticipated over the life of the project. true false what role does class play in this story? does the level of entitlement mrs. das seems to feel have to do with her american or indian heritage? An plane covers 50 miles in 1/5 of an hour. How many miles can the plane cover in 5 hours Which of the following curative factors as described by Irvin D. Yalom makes group psychotherapy an effective process?(all of these)instilling hope, sharing universality, and imparting informationrecapitulating the primary family groupsharing catharsisfostering altruism , centeredness, and spirtuality What effect did the railroad have on industries Find the missing side length. the nurse provides teaching for a patient who will begin taking indomethacin to treat symptoms of rheumatoid arthritis. which statement by the patient indicates a need for further teaching? match the following definitions to their possible organizational patterns for arguments. [--] con idea-> refutation, con idea 2-> refutation, and con idea 3-> refutation [--] pro idea 1, pro idea 2, and con idea-> refutation [--] con idea-> refutation pro idea 1 and pro idea 2 when a letterform is measured vertically, from the bottom of the descender to the top of the ascender, what unit is used? a.) mean line b.) point c.) x-height d.) pica traits, skills, knowledge areas, or attributes that are required for successful job performance are known as a quantity with an initial value of 2900 grows exponentially at a rate such that the quantity doubles every 7 days. what is the value of the quantity after 54 hours, to the nearest hundredth A smartphone, in addition to a laptop, ____ available to all staff members Read this sentence.Many people considered her cultured because she liked to listen to opera and read books in French. Based on the context of the sentence, which word gives it a positive connotation? A. opera B. cultured C. books D. considered