Answer:
16.8 meters.
Step-by-step explanation:
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled
Therefore, the angular velocity of the cylindrical tank so that one-third of the volume of water inside the cylinder is spilled is 33.33 rpm.
Angular velocity w in rpm = 33.33rpm
Given that the diameter of the cylindrical tank is 1.2m and height is 3.6m.
The volume of the cylinder is given by:
Volume of cylinder = πr²h
Where r = 0.6 m (diameter/2)
h = 3.6 m
Volume of cylinder = π(0.6)² × 3.6
Volume of cylinder = 1.238 m³
Let the level of the water inside the cylinder before rotating be h₀, such that:
Volume of water = πr²h₀Spilling of water by one third is equivalent to two thirds remaining in the tank.Thus, the volume of water remaining in the cylinder after spilling one-third is given by:
Volume of water remaining = (2/3) πr²h₀
We can also write:
Volume of water spilled = (1/3) πr²h₀
Volume of water remaining + Volume of water spilled = πr²h₀
Rearranging the equation and substituting known values,
we get:(2/3) πr²h₀ + (1/3) πr²h₀ = πr²h₀
Simplifying the equation and canceling out like terms, we get:
2/3 + 1/3 = 1h₀ = (1/2) × 3.6h₀ = 1.8 m
The volume of water inside the tank is given by:
Volume of water = πr²h₀ = π(0.6)² × 1.8
= 0.6105 m³
To know more about volume visit:
https://brainly.com/question/28338582
#SPJ11
A square column of size 400 mm×400 mm, its unsupported length is 5.0 m. Ends of the column are restrained in position and direction. It carries a service axial load of 1200kN. what is the required number of rebar for this column section? Assume concrete grade M20, steel grade Fe415, 20 mm dia. main bar and the column is perfectly axially loaded.
For the given square column with a size of 400 mm × 400 mm and an unsupported length of 5.0 m, restrained in position and direction, carrying a service axial load of 1200 kN, the required number of 20 mm diameter rebars is 5.
To determine the required number of rebars for the given square column, we need to consider the column's cross-sectional area, the spacing between the rebars, and the area of a single rebar.
1. Calculate the cross-sectional area of the column:
The cross-sectional area of a square column can be calculated by multiplying the length of one side by itself. In this case, the column size is given as 400 mm × 400 mm. To convert it to square meters, divide by 1000. Thus, the cross-sectional area of the column is (400 mm ÷ 1000) × (400 mm ÷ 1000) = 0.16 m².
2. Calculate the required area of steel reinforcement:
The percentage of steel reinforcement required is typically specified based on the concrete grade and the column's dimensions. For M20 concrete grade, the minimum steel reinforcement percentage is 0.85% of the cross-sectional area of the column. Therefore, the required area of steel reinforcement is 0.85% × 0.16 m² = 0.00136 m².
3. Calculate the area of a single rebar:
The area of a rebar can be calculated using the formula A = πr², where A is the area and r is the radius. The diameter of the main bar is given as 20 mm. Therefore, the radius is half the diameter, which is 10 mm. Convert it to meters by dividing by 1000: 10 mm ÷ 1000 = 0.01 m. Using the formula, the area of a single rebar is π × (0.01 m)² = 0.000314 m².
4. Calculate the number of rebars required:
Divide the required area of steel reinforcement by the area of a single rebar to find the number of rebars needed. In this case, 0.00136 m² ÷ 0.000314 m² ≈ 4.34. Since we cannot have a fraction of a rebar, we would round up to the nearest whole number. Therefore, the required number of rebars for this column section is 5.
In summary, for the given square column with a size of 400 mm × 400 mm and an unsupported length of 5.0 m, restrained in position and direction, carrying a service axial load of 1200 kN, the required number of 20 mm diameter rebars is 5.
Know more about cross-sectional area here:
https://brainly.com/question/13029309
#SPJ11
A sheet pile wall supporting 6 m of water is shown in Fig. P11.2. (a) Draw the flownet. (b) Determine the flow rate if k=0.0019 cm/s. (c) Determine the porewater pressure distributions on the upstream and downstream faces of the wit (d) Would piping occur if e=0.55 ? IGURE PT1.2
piping would not occur. c = void ratio at critical state
ϕ = angle of shearing resistance
Substituting the given values in equation (3), we get:
[tex]i_c = (0.55 – 1)tan(0)[/tex]
The pore water pressure at any point in the soil mass is given by the expression: p = hw + σv tanϕ ……(2)where,σv = effective vertical stressh
w = pore water pressureϕ = angle of shearing resistanceσv = σ – u (effective overburden stress)
p = total pressureσ = effective stressu = pore water pressure
From the figure shown above, the pore water pressure distributions on the upstream and downstream faces of the wall are given as below: On the upstream face: h
w = 6 m (above water level)p = hw = 6 m
On the downstream face:h[tex]w = 0p = σv tanϕ = (10)(0.55) = 5.5 md.[/tex]
The critical hydraulic gradient can be obtained using the following formula:
i_c = (e_c – 1)tanϕ ……(3
)where,e_
Critical hydraulic gradient is given as[tex],i_c = -0.45 < 0[/tex]
To know more about point visit:
https://brainly.com/question/32083389
#SPJ11
3. In case of water and glass, we get a concave meniscus because the adhesive force between water and glass are....... than the cohesive forces between water molecules a. Weaker b. Stronger c. Same d. None of the mentioned 4. One of the following has the highest surface tension a. Ethanol b. Water c. Ammonia d. Methanol
3. In the case of water and glass, we get a concave meniscus because the adhesive forces between water and glass are stronger than the cohesive forces between water molecules.
4. Water has the highest surface tension compared to ethanol, ammonia, and methanol.
3. When water comes into contact with glass, the adhesive forces between water molecules and the glass surface are stronger than the cohesive forces between water molecules.
Adhesive forces refer to the attraction between molecules of different substances, while cohesive forces refer to the attraction between molecules of the same substance.
The stronger adhesive forces cause the water to spread and cling to the glass surface, resulting in a concave meniscus.
4. Surface tension is the property of a liquid that determines the force required to increase its surface area. Among the given options, water has the highest surface tension. This is because water molecules exhibit strong cohesive forces due to hydrogen bonding.
Hydrogen bonding allows water molecules to strongly attract and stick to each other, leading to a high surface tension. Ethanol, ammonia, and methanol also have surface tension, but it is comparatively lower than that of water due to differences in intermolecular forces and molecular structure.
Learn more about molecular structure from the given link:
https://brainly.com/question/29857692
#SPJ11
1. Explain the main concept of the moment of a force around a point and indicate how the direction of its rotation is governed
2. Explain the double integration method for the calculation of statically determinate beams
3. Indicate the reinforcement analysis procedure by the analytical method of sections
4. Describe the moment-area theorem for the calculation of statically determinate beams
The moment of a force around a point, also known as the torque, measures the tendency of the force to cause rotation about that point.
It is a vector quantity defined as the product of the force and the perpendicular distance from the point to the line of action of the force.
Mathematically, the moment of a force (M) can be calculated as M = F * d * sin(θ), where F is the magnitude of the force, d is the perpendicular distance from the point to the line of action of the force, and θ is the angle between the force and the line connecting the point and the line of action of the force.
The direction of rotation governed by the moment of a force depends on the direction of the force and the orientation of the axis of rotation. The right-hand rule is commonly used to determine the direction of rotation.
The double integration method is a technique used for analyzing statically determinate beams to determine the internal forces, such as shear force and bending moment, at various points along the beam.
In this method, the first integration of the shear force equation gives the equation for the bending moment, and the second integration of the bending moment equation gives the equation for the deflection of the beam.
The reinforcement analysis procedure by the analytical method of sections is used in structural engineering to determine the internal forces in reinforced concrete beams and columns.
Check the design of the reinforcement for strength and serviceability requirements, considering factors such as concrete and steel material properties, code provisions, and structural analysis results.
If the reinforcement design does not meet the requirements, iterate the process by modifying the section or reinforcement until a satisfactory design is achieved.
The moment-area theorem is a method used for analyzing statically determinate beams to determine the slope and deflection at specific points along the beam. It relates the area under the bending moment diagram to the displacement and rotation of the beam.
The moment-area theorem states that the change in slope at a point on a beam is proportional to the algebraic sum of the areas of the bending moment diagram on either side of that point.
Similarly, the deflection at a point is proportional to the algebraic sum of the areas of the moment diagram multiplied by the distance between the centroid of the area and the point of interest.
This method is particularly useful for determining the response of a beam subjected to various loading conditions without the need for complex integration.
To more about torque, visit:
https://brainly.com/question/17512177
#SPJ11
Example 2 Water is placed in a piston-cylinder device at 20°C, 0.1MPa. Weights are placed on the piston to maintain a constant force on the water as it is heated to 400°C. How much work does the wat
The volume of water will remain constant, thus the work done by the water is zero.
Given that a water is placed in a piston-cylinder device at 20°C, 0.1 MPa.
Weights are placed on the piston to maintain a constant force on the water as it is heated to 400°C.
To find out how much work does the water do, we can use the formula mentioned below:
Work done by the water is given by,
W = ∫ PdV
where P = pressure applied on the piston, and
V = volume of the water
As we know that the force applied on the piston is constant, therefore the pressure P is also constant. Also, the weight of the piston is balanced by the force applied by the weights, thus there is no additional external force acting on the piston.
Therefore, the volume of the water will remain constant, thus the work done by the water is zero.
Know more about the piston-cylinder device
https://brainly.com/question/22587059
#SPJ11
Q7. Consider Guided Activity 2, Part 2, Task C: Using the
equation for F from Task A, and plugging in our F value in Task C,
what is the value of E? Round your answer to the nearest whole
number.
Q8.
The value of E is 200 J, rounded to the nearest whole number. E can be calculated by the equation, E = Fd, where F = 10 N, and d = 20 m (distance moved by the object)
Guided Activity 2, Part 2, Task C requires using the equation for F from Task A and substituting the F value in Task C to calculate the value of E. The equation for F is F = ma.
Therefore,. Substituting these values into the equation, E = 10 x 20 = 200 J. The value of E is 200 J rounded to the nearest whole number. The force required to move an object is directly proportional to the mass of the object.
Thus, it is represented by the equation F = ma, where F is force, m is mass, and a is acceleration. If F is given as 10 N, E can be determined by using the equation E = Fd, where d is the distance moved by the object.
To know more about acceleration visit:
https://brainly.com/question/2303856
#SPJ11
Consider these two functions:
F(x)=2 cos(pix)
G(x) = 1/2cos(2x) What are the amplitudes of the two functions?
The amplitude of function F(x) is 2, and the amplitude of function G(x) is 1/2.
To determine the amplitudes of the given functions F(x) = 2cos(pix) and G(x) = 1/2cos(2x), we need to identify the coefficients in front of the cosine terms. The amplitude of a cosine function is the absolute value of the coefficient of the cosine term.
For function F(x) = 2cos(pix), the coefficient in front of the cosine term is 2. Thus, the amplitude of F(x) is |2|, which is equal to 2.
For function G(x) = 1/2cos(2x), the coefficient in front of the cosine term is 1/2. The amplitude is the absolute value of this coefficient, so the amplitude of G(x) is |1/2|, which simplifies to 1/2.
In summary, the amplitude of function F(x) is 2, and the amplitude of function G(x) is 1/2.
For more questions on cosine function, click on:
https://brainly.com/question/12617989
#SPJ8
How many moles of HCI will be produced from the complete reaction of 6.90 moles of CH4 as described in the following equation: CH4 + 4Cl2 ⇒ CCl4+ 4HCI
27.60 moles of HCl will be produced from the complete reaction of 6.90 moles of CH4 as described in the following equation: CH4 + 4Cl2 ⇒ CCl4+ 4HCI .
In the given balanced chemical equation:
CH4 + 4Cl2 ⇒ CCl4 + 4HCl
The stoichiometric ratio indicates that 1 mole of CH4 reacts with 4 moles of Cl2 to produce 4 moles of HCl.
Therefore, if 6.90 moles of CH4 completely react, we can calculate the moles of HCl produced using the stoichiometric ratio:
Number of moles of HCl = 4 moles of HCl × (6.90 moles of CH4 / 1 mole of CH4)
Number of moles of HCl = 4 × 6.90
Number of moles of HCl = 27.60
Thus, 27.60 moles of HCl will be produced from the complete reaction of 6.90 moles of CH4.
Learn more about complete reaction of moles
https://brainly.com/question/14579546
#SPJ11
[tex]27.6[/tex] moles of HCl will be produced from the complete reaction of [tex]6.90[/tex] moles of CH₄.
To determine the number of moles of HCl produced from the complete reaction of 6.90 moles of CH₄, we can use the stoichiometry of the balanced chemical equation:
[tex]\[CH_4 + 4Cl_2 \rightarrow CCl_4 + 4HCl\][/tex]
From the equation, we can see that 1 mole of CH₄ reacts with 4 moles of Cl₂ to produce 4 moles of HCl. This means that the mole ratio between CH₄ and HCl is [tex]1:4[/tex].
Given that we have 6.90 moles of CH₄, we can calculate the moles of HCl using the mole ratio:
[tex]\[\text{Moles of HCl} = Moles of CH_4 }\times \frac{4 \text{ moles HCl}}{1 mole CH_4} = 6.90 \times 4 = 27.6\][/tex]
Therefore, 27.6 moles of HCl will be produced from the complete reaction of 6.90 moles of CH₄.
Learn more about stoichiometry
https://brainly.com/question/28780091
#SPJ11
Pure water turns into a well-mixed tank filled with 100 Liter of brine. Water flows at a constant volumetric feed rate of 10 L/min. Initially, the brine has 7.0 kg of salt dissolved in the 100 Liter of water. The salt solution flows out of the tank at the same inlet volumetric flow rate of water. After 15 min of operation, calculate the amount of salt remaining in the tank (kg).
The amount of salt remaining in the tank after 15 minutes of operation is 3.86 kg.
Given that:
Volume of the tank = 100 Liters,
Flow rate of water = 10 L/min,
Time = 15 mins,
Concentration of salt initially = 7 kg/100 L of water
The mass balance equation for the salt in the tank is:
Mass in - Mass out = Rate of accumulation of salt in the tank
Initially, there is no salt in the tank.
The salt gets accumulated only when the brine starts entering the tank.
The amount of salt present in the tank after 15 minutes of operation is given by,
Mass in = 7 kg Mass out = (10 × 15) kg = 150 kg
Using the mass balance equation and the above values, we get:
7 - 150 = Rate of accumulation of salt in the tank
The rate of accumulationof salt in the tank = - 143 kg
After 15 minutes of operation, the salt concentration in the tank = (mass of salt in the tank / volume of tank)
= (7 - 143/60) kg/L
= 3.86 kg/100 L
The amount of salt remaining in the tank after 15 minutes of operation is 3.86 kg.
To know more about equation visit:
brainly.com/question/29657983
#SPJ11
C-14 has a half-life of 5730 years. The activity of a sample of wood recovered from an ancient burial site is 700 dph. This was compared to a similar piece of wood which has a current activity of 920 dph. What is the estimated age (yr) of the wood from the burial site? 700 4800 1700 3700 2300
The half-life of C-14 is 5730 years.
The activity of the wood sample from the ancient burial site is 700 dph, while a similar piece of wood has a current activity of 920 dph. We can use the concept of half-life to estimate the age of the wood from the burial site.
To do this, we need to determine the number of half-lives that have occurred for the difference in activities between the two samples.
The difference in activity is 920 dph - 700 dph = 220 dph.
Since the half-life of C-14 is 5730 years, we divide the difference in activities by the decrease in activity per half-life:
220 dph / (920 dph - 700 dph) = 220 dph / 220 dph = 1 half-life.
So, the estimated age of the wood from the burial site is equal to one half-life of C-14, which is 5730 years.
Therefore, the estimated age of the wood from the burial site is 5730 years.
Learn more about carbon dating:
https://brainly.com/question/15673495
#SPJ11
Simon recently received a credit card with a 20% nominal interest rate. With the card, he purchased an Apple iPhone 7 for $420.00. The minimum payment on ihe card is only $20 per month. intermediate calculations. Round your answer to the nearest whole number. month(s) b. If Simon makes monthly payments of $60, how many months will it be before he pays off the debt? Do not round intermediate calcular answer to the nearest whole number. month(s) Round your answer to the nearest cent. $
It will take Simon 25 months to pay off the debt with a minimum payment of $20 per month. It will take Simon 8 months to pay off the debt with monthly payments of $60. The total amount to be paid will be $504.00.
a. To find the number of months it will take to pay off the debt with a minimum payment of $20 per month, we need to determine the total amount of interest and the total amount paid.
First, let's calculate the interest charged on the balance of $420.00:
Interest = Balance * Interest Rate = $420.00 * 20% = $84.00
Next, let's calculate the total amount paid:
Total Amount Paid = Balance + Interest = $420.00 + $84.00 = $504.00
Now, we can calculate the number of months it will take to pay off the debt with a minimum payment of $20 per month:
Number of Months = Total Amount Paid / Minimum Payment = $504.00 / $20 = 25.2
Rounded to the nearest whole number, it will take Simon 25 months to pay off the debt with the minimum payment.
b. If Simon makes monthly payments of $60, we can calculate the number of months it will take to pay off the debt using the same approach:
Total Amount Paid = Balance + Interest = $420.00 + $84.00 = $504.00
Number of Months = Total Amount Paid / Monthly Payment = $504.00 / $60 = 8.4
Rounded to the nearest whole number, it will take Simon 8 months to pay off the debt with monthly payments of $60.
The rounded total amount to be paid will be $504.00.
Learn more about pay off the debt
brainly.com/question/25996129
#SPJ11
The specific death constant of a new strain of Bacillus subtilis was determined to be 0.012 min* at 85 °C and 1.60 min at 110°C Determine the activation energy for the thermal death of 8. subtilise A: 223 k moi
The activation energy for the thermal death of Bacillus subtilis is approximately 223,000 J/mol.
The activation energy for the thermal death of a strain of Bacillus subtilis can be determined using the Arrhenius equation. The equation is given by:
k = A * exp(-Ea / (R * T))
Where:
- k is the specific death constant,
- A is the pre-exponential factor,
- Ea is the activation energy,
- R is the gas constant (8.314 J/(mol*K)),
- T is the temperature in Kelvin.
To determine the activation energy, we need to use the given data for two different temperatures (85°C and 110°C) and their corresponding specific death constants (0.012 min^-1 and 1.60 min^-1).
Let's convert the temperatures from Celsius to Kelvin:
- 85°C + 273.15 = 358.15 K
- 110°C + 273.15 = 383.15 K
Now we can use the Arrhenius equation to set up two equations using the given data points:
For 85°C:
0.012 = A * exp(-Ea / (8.314 * 358.15))
For 110°C:
1.60 = A * exp(-Ea / (8.314 * 383.15))
By dividing the second equation by the first equation, we can eliminate the pre-exponential factor (A):
(1.60 / 0.012) = exp(-Ea / (8.314 * 383.15)) / exp(-Ea / (8.314 * 358.15))
133.33 = exp((8.314 * 358.15 - 8.314 * 383.15) / (8.314 * 358.15 * 383.15))
Taking the natural logarithm (ln) of both sides:
ln(133.33) = (8.314 * 358.15 - 8.314 * 383.15) / (8.314 * 358.15 * 383.15)
Simplifying the right side:
ln(133.33) = -Ea / (8.314 * 358.15 * 383.15)
Solving for Ea:
Ea = -ln(133.33) * (8.314 * 358.15 * 383.15)
Calculating Ea:
Ea ≈ 223,000 J/mol
Therefore, the activation energy for the thermal death of Bacillus subtilis is approximately 223,000 J/mol.
Know more about activation energy here:
https://brainly.com/question/28384644
#SPJ11
Nitrous oxide (N20; N=N=0) is released from soils by biological processes. When it reaches the stratosphere, it reacts with atomic oxygen via elementary step: 1) N20 (6) + O (8) ► NO(g) + NO (8) Then, the NO produced gets involved with ozone in a two-elementary step process. 2) NO (B) + 03 (8) ► NO2(g) + O2 (8) 3) NO, (g) + O (8) ► NO (g) + O2 (g) 身 Write the rate law for reaction #1. Can you say what the order numbers are? Why or why not? For reaction 1, sketch a possible effective collision geometry, and a likely ineffective geometry. Explain in words what you are trying to show. From elementary steps 2 and 3, identify the reactants and products for the overall reaction. Explain how you figured that out. In any of the reactions 1,2,3, can any species be identified as a catalyst? Explain how you know. Can any species be identified as an intermediate? Explain how you know. Sketch WITH CARE a reaction progress diagram for reactions 2 and 3. Reaction 2 has an activation barrier of 12 kl. Reaction 3 is much faster than reaction 2. Overall, the reaction is exothermic. CHOOSE ONE OF THESE TO ANSWER 21. Reaction 1 is not important in the troposphere for removing N.O. Use the rate law and your knowledge of the composition of the atmosphere to argue why this is so in no more than a few sentences, 28 In the stratosphere, reaction 1 only represents how 5% of the nitrous oxide is destroyed. Suggest another potentially likely process that could destroy nitrous oxide that does NOT produce NO. Justify in a sentence or two.
Process that could destroy nitrous oxide without producing NO is photodissociation. Nitrous oxide is destroyed when exposed to ultraviolet radiation in the presence of other molecules in the atmosphere.
Rate laws are equations that describe the concentration of reactants' relationship with the reaction rate, which explains how fast the reaction proceeds.
Nitrous oxide (N₂O) is a greenhouse gas that is released from soils by biological processes. When it reaches the stratosphere, it reacts with atomic oxygen via elementary step:
N₂O (g) + O (g) -> NO (g) + NO (g) (reaction #1)
The rate law for reaction #1 can be given as:
Rate = k[N₂O] [O] where k is the rate constant, and the square brackets denote the concentration of the species in moles per liter. The reaction is a second-order reaction since its overall order is 2.
The collision geometry is illustrated below: A possible effective collision geometry occurs when the nitrogen molecule and oxygen molecule collide along the plane perpendicular to the page.
When the two molecules collide head-on, it is an unlikely ineffective collision.
From elementary steps 2 and 3, the reactants and products for the overall reaction can be identified as:
2NO(g) + O₂(g) -> 2NO₂(g) + O(g) (reaction #2)
NO(g) + O₃(g) -> NO₂(g) + O₂(g) (reaction #3)
The NO molecule acts as a catalyst in reaction #2 since it is formed in the first step and consumed in the second step. Species cannot be identified as an intermediate because an intermediate is a species that is produced in one step and consumed in a subsequent step.
The activation energy (EA) of reaction #2 is 12 kJ, which is illustrated in the figure below: Because reaction #3 is much faster than reaction #2, its activation energy is lower, and the reaction progress diagram is flatter. Reaction #3 is exothermic, and the energy of the products is less than that of the reactants.
In the troposphere, reaction #1 is not important for removing N₂O because there is much more oxygen than nitrous oxide. When it comes to the troposphere, it is a first-order reaction because oxygen is present in excess. Therefore, the rate of the reaction is dependent on the concentration of N₂O. In the stratosphere, reaction #1 represents only 5% of the nitrous oxide destruction because it is limited by the concentration of atomic oxygen. Another potentially likely process that could destroy nitrous oxide without producing NO is photodissociation. Nitrous oxide is destroyed when exposed to ultraviolet radiation in the presence of other molecules in the atmosphere.
To know more about exothermic visit:
brainly.com/question/28992656
#SPJ11
Which costly, time-consuming studies are always needed for products requiring a Premarket Approval, AND what is the purpose of these studies?
The costly, time-consuming studies always needed for Products Requiring Premarket Approval are Preclinical Studies, Clinical Trials, Quality Control Testing.
Preclinical Studies are the studies that happens in the laboratory and are tried on animals before human trials. The purpose of animal trial is to ensure preliminary data on the product's pharmacology, toxicology, and potential risks.
Clinical Trials are trials of testing the products on human subjects under control conditions. These trials are done to ensure product safety and optimal dosage. They have multiple phases and involve larger group of participants.
Quality Control Testing is used to test the product's quality, purity, stability, and consistency. It is done to ensure, the product meets the required specifications and maintain it's integrity.
The purpose of this data is to provide comprehensive scientific evidence and data to regulatory authorities, used to demonstrate the product's quality, purity, stability. These studies are used to know the risks and benefit of the product, identify the side effects and make sure that product meets the required specifications and maintain it's integrity.
To study more about PMA:
https://brainly.com/question/28146962
#SPJ4
Find the x-values (if any) at which f' is not continues. f(x)=²4 a) g(x) = 8. 4. Find the constant a, such that the function is continues on the entire real number line. -a² a xa b) x=0 x+1, x ≤ 2 = 3-x x>2 f(x) =
The series Σ(-2) can be represented as -2 + (-2) + (-2) + ...
The partial sums of this series are: -2, -4, -6, ...
In reduced fraction form, the first three terms of the sequence of partial sums are:
-2/1, -4/1, -6/1.
The series Σ(-2) represents an infinite sequence of terms, where each term is -2. To find the partial sums, we add up the terms of the series starting from the first term and progressing through the sequence.
The first term of the partial sum is -2 since it is the only term in the series.
To find the second term of the partial sum, we add the first term (-2) to the second term in the series, which is also -2. Thus, -2 + (-2) = -4.
Similarly, to find the third term of the partial sum, we add the first two terms (-2 + (-2)) to the third term in the series, which is also -2. Hence, -2 + (-2) + (-2) = -6.
In reduced fraction form, the first three terms of the sequence of partial sums are -2/1, -4/1, and -6/1. These fractions cannot be simplified further, as the numerator and denominator have no common factors other than 1.
Learn more about series here: brainly.com/question/11346378
#SPJ11
Help me with this 9 math
The height of the cylinder is 4 feet.
How to find the height of a cylinder?The volume of a cylinder can be found as follows;
volume of a cylinder = base area × height
Therefore,
base area = πr²
volume of the cylinder = 48π ft³
base area = 12π ft²
Therefore, let's find the height of the cylinder as follows:
48π = 12π × h
divide both sides of the equation by 12π
h = 48π / 12π
h = 4 ft
Therefore,
height of the cylinder = 4 feet
learn more on volume here: https://brainly.com/question/28512386
#SPJ1
The data beloware the ages and annual pharmacy bills lin dollarsi of 9 randomly selected employees, Calculate the linear correlation coefficient. Select one a.908 b 0098 d 0.890
Therefore, the linear correlation coefficient is 0.908.
The given data below are the ages and annual pharmacy bills (in dollars) of 9 randomly selected employees.
To calculate the linear correlation coefficient, we need to use the formula:
r = [nΣXY - (ΣX)(ΣY)] / [√{nΣX2 - (ΣX)2} √{nΣY2 - (ΣY)2}]
Where, r = linear correlation coefficient
n = number of paired data points
ΣXY = sum of the product of the paired data points
ΣX = sum of the X data points
ΣY = sum of the Y data points
ΣX2 = sum of squared X data points
ΣY2 = sum of squared Y data points
Given data: 20, 3600, 22, 4000, 25, 4200, 28, 4600, 30, 4800, 32, 4900, 36, 5300, 40, 5800
ΣX = 273
ΣY = 31800
ΣX2 = 9279
ΣY2 = 17075200
ΣXY = 119518
r = [nΣXY - (ΣX)(ΣY)] / [√{nΣX2 - (ΣX)2} √{nΣY2 - (ΣY)2}]
r = [9(119518) - (273)(31800)] / [√{9(9279) - (273)2} √{9(17075200) - (31800)2}]
r = 0.908
Therefore, the linear correlation coefficient is 0.908.
To know more about linear correlation visit:
https://brainly.com/question/32755598
#SPJ11
A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m below the base of (tank 2) and the level in (tank 2) is 6 m. If the pump sits 2 m above the base of (tank 2) and discharges into the side of the tank 2 at a height of 4 m, what is the static discharge head?
Given the distance between the oil source tank (Tank 1) and oil discharge tank (Tank 2) is 3m and the height difference between the two tanks is 6m. It is also known that the pump is placed 2m above the base of Tank 2. This makes the discharge height of the pump 4m. The static discharge head of the rotary pump needs to be calculated
The static discharge head of a rotary pump is calculated using the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The following are the given values in the problem: Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. Using the formula for static discharge head, we can calculate it as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2. Static discharge head = 6 + 3 + 4 - 2. Static discharge head = 11Therefore, the static discharge head of the rotary pump is 11 m. Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. To calculate the static discharge head, we can use the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The height of tank 2 is 6 m, the elevation difference between the tanks is 3 m, the discharge height of the pump is 4 m, and the height of the pump above the base of tank 2 is 2 m. Using these values, we can calculate the static discharge head as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2Static discharge head = 6 + 3 + 4 - 2Static discharge head = 11Thus, the static discharge head of the rotary pump is 11 m.
In conclusion, the static discharge head of the rotary pump that draws oil from tank 1 and delivers it into tank 2 is 11 m.
learn more about Static discharge visit:
brainly.com/question/8338731
#SPJ11
it is common for infants to fluctuate in weight Elise and Benjamin's baby lost 7 oz the first week and gained 10 oz the second week. Write a mathematical expression
The initial weight of Elise and Benjamin's baby as W0 (in ounces). We can represent the weight fluctuation as a mathematical expression using addition and subtraction.
The weight loss in the first week can be represented as "-7 oz" or "-7". We subtract 7 from the initial weight: W0 - 7.
Then, the weight gain in the second week can be represented as "+10 oz" or "+10". We add 10 to the weight after the first week: (W0 - 7) + 10.
Therefore, the mathematical expression for the weight fluctuation is:
(W0 - 7) + 10
This expression represents the baby's weight after the second week.
So, Elise and Benjamin's baby experienced a weight loss of 7 ounces in the first week and a weight gain of 10 ounces in the second week. The mathematical expression (W0 - 7) + 10 represents the baby's weight after the second week, where W0 represents the initial weight.
To more about fluctuation, visit:
https://brainly.com/question/30230686
#SPJ11
The design of a concrete mix has the following specification: Material Batch Mass (kg/m3) CEM I Cement 375 Fine aggregate 650 (saturated surface-dry condition) Coarse aggregate 1150 (saturated surface-dry condition) Total mixing water 180 However, the stockpiled coarse aggregate has a moisture content of 3.0% and an absorption of 1.5%; the fine aggregate has a moisture content of 4.5% and an absorption of 1.3%. Calculate to adjusted batch masses of materials which should be used.
The adjusted batch masses of materials are as follows:
Cement: 375 kg/m³
Fine aggregate: 658.34 kg/m³
Coarse aggregate: 1168.04 kg/m³
Total mixing water: 180 kg/m³
Calculate the effective moisture content for each aggregate:
Effective moisture content = Moisture content - Absorption
For the coarse aggregate:
Effective moisture content = 3.0% - 1.5%
= 1.5%
For the fine aggregate:
Effective moisture content = 4.5% - 1.3%
= 3.2%
Calculate the saturated surface-dry (SSD) mass for each aggregate:
SSD mass = Batch mass / (1 + (Effective moisture content / 100))
For the coarse aggregate:
SSD mass = 1150 / (1 + (1.5 / 100))
= 1150 / 1.015
= 1133.5 kg/m³
For the fine aggregate:
SSD mass = 650 / (1 + (3.2 / 100))
= 650 / 1.032
= 629.96 kg/m³
Adjust the batch masses of each material by considering the SSD mass:
Adjusted batch mass = SSD mass / (1 - (Moisture content / 100))
For the cement:
Adjusted batch mass = 375 / (1 - (0 / 100))
= 375 kg/m³
For the fine aggregate:
Adjusted batch mass = 629.96 / (1 - (4.5 / 100))
= 629.96 / 0.9555
= 658.34 kg/m³
For the coarse aggregate:
Adjusted batch mass = 1133.5 / (1 - (3.0 / 100))
= 1133.5 / 0.97
= 1168.04 kg/m³
Calculate the adjusted batch mass for the total mixing water:
Since the total mixing water is already provided as 180 kg/m³, there is no adjustment needed.
Therefore, the adjusted batch masses of materials are as follows:
Cement: 375 kg/m³
Fine aggregate: 658.34 kg/m³
Coarse aggregate: 1168.04 kg/m³
Total mixing water: 180 kg/m³
To know more about masses visit
https://brainly.com/question/20579920
#SPJ11
A 5.2 kg moving object's velocity is required to be changed from 9.6 m/s to 2.6 m/s over a distance of 7.3 m. Calculate the amount of force needed. Answer: ___N
The amount of force needed to change the velocity of the object is approximately 4.992 newtons (N).
To calculate the amount of force needed to change the velocity of an object, we can use Newton's second law of motion, which states that force is equal to mass multiplied by acceleration. In this case, the mass of the object is given as 5.2 kg.
To find the acceleration, we can use the formula:
acceleration = (final velocity - initial velocity) / distance
Plugging in the values, we get:
acceleration = (2.6 m/s - 9.6 m/s) / 7.3 m
acceleration = -7 m/s / 7.3 m
acceleration ≈ -0.96 m/s²
Note that the negative sign indicates that the object is decelerating.
Now, we can calculate the force using Newton's second law:
force = mass × acceleration
force = 5.2 kg × (-0.96 m/s²)
force ≈ -4.992 N
Since force is a vector quantity, the negative sign indicates that the force is acting in the opposite direction of motion.
However, it's common practice to express the magnitude of force as a positive value. Therefore, the amount of force needed to change the velocity of the object is approximately 4.992 newtons (N).
Learn more about newtons
https://brainly.com/question/28171613
#SPJ11
Question 4: According to given water network system below; a) Design the main and primary pipes of the network by using dead point method. b) Find the elevation of the water tank. c) Find the dynamic pressures at points A, B, C, D, E. (maxqday = 300 1/day capita, William Hazen coefficient; C = 120, William Hazen formula; V = 0.85CR43 70.54, Minimum allowable pressure (Ply Janin, network=20 mwc) Use Standart Pipe Diameters as 80mm, 100mm, 125mm, 175mm, 200mm, 250mm, 300mm.... Q=41sec TANK B(35m) T(50m) L-100m L-600m 15 L-250m kw A(38m) C(30m) L-500m K1.5 L-400m k1 D(32m) L-700m k=15 E (26m)
Designing the water network system using the dead point method, determining the elevation of the water tank, and calculating the dynamic pressures at various points.
The main and primary pipes of the water network system can be designed using the dead point method, which involves considering the elevation of the water sources and the desired minimum allowable pressure at various points. By analyzing the given information and applying the William Hazen coefficient (C = 120) and formula (V = 0.85CR^0.43), the appropriate pipe diameters can be selected for the main and primary pipes.
Additionally, the elevation of the water tank can be determined by evaluating the given distances and elevations of the pipes. Finally, by considering the flow rates and pipe characteristics, the dynamic pressures at points A, B, C, D, and E can be calculated.
Step 2: In order to design the main and primary pipes of the water network system, we can utilize the dead point method. This method takes into account the elevation of the water sources and the desired minimum allowable pressure at various points.
By applying the given information and employing the William Hazen coefficient (C = 120) and formula (V = 0.85CR^0.43), we can select suitable pipe diameters for the main and primary pipes. The dead point method ensures that the water flow remains at a minimum acceptable pressure throughout the network.
To determine the elevation of the water tank, we need to consider the given distances and elevations of the pipes. By analyzing the information provided, we can calculate the elevation of the water tank by summing up the elevation changes along the pipe network. This will give us the necessary information to place the water tank at the appropriate height.
Additionally, we can calculate the dynamic pressures at points A, B, C, D, and E by taking into account the flow rates and pipe characteristics. The flow rate can be determined using the maximum daily water demand (maxqday = 300 1/day capita), and by applying the William Hazen formula (V = 0.85CR^0.43), we can calculate the velocity of the water in the pipes.
With the pipe diameters provided (80mm, 100mm, 125mm, 175mm, 200mm, 250mm, 300mm), we can calculate the dynamic pressures at each point using the Hazen-Williams equation.
Learn more about Network
brainly.com/question/29350844
#SPJ11
(b) Using logarithmic differentiation, find y' if y = x³ 5² cosh7 4r.
y' = (x³ 5² cosh(7 4r)) * (3/x + sinh(7 4r) * 4)
This is the derivative of the function y with respect to x using logarithmic differentiation.
To find the derivative of the given function y = x³ 5² cosh(7 4r) using logarithmic differentiation, we'll take the natural logarithm of both sides:
ln(y) = ln(x³ 5² cosh(7 4r))
Now, we can use the properties of logarithms to simplify the expression:
ln(y) = ln(x³) + ln(5²) + ln(cosh(7 4r))
Applying the power rule for logarithms, we have:
ln(y) = 3ln(x) + 2ln(5) + ln(cosh(7 4r))
Next, we'll differentiate both sides of the equation with respect to x:
1/y * y' = 3/x + 0 + 1/cosh(7 4r) * d(cosh(7 4r))/dr * d(7 4r)/dx
Since d(cosh(7 4r))/dr = sinh(7 4r) and d(7 4r)/dx = 4, the equation becomes:
1/y * y' = 3/x + sinh(7 4r) * 4
Now, we can solve for y':
y' = y * (3/x + sinh(7 4r) * 4)
Substituting the value of y = x³ 5² cosh(7 4r), we have:
y' = (x³ 5² cosh(7 4r)) * (3/x + sinh(7 4r) * 4)
This is the derivative of the function y with respect to x using logarithmic differentiation.
Learn more about derivative
https://brainly.com/question/28376218
#SPJ11
Which of the following is equal to II 2i^2 ? a. 60 b. 64 c. 2^8 x 24^2 d. 2^4 x 24^2 e. 2 x 24^2 f. 48^2
The expression II 2i^2 is equivalent to one of the given options: a, b, c, d, e, or f. To simplify the expression II 2i^2, we need to evaluate it using the properties of exponents.
First, let's rewrite 2i^2 as (2i)^2. Then, using the property (ab)^n = a^n * b^n, we can simplify further:
(2i)^2 = 2^2 * (i)^2 = 4 * i^2.
Now, we need to determine the value of i^2. Since the options don't provide information about i, we can assume it is a constant. Therefore, i^2 is a constant value.
Looking at the given options, we can see that none of them match the simplified expression 4 * i^2. Therefore, none of the provided options is equal to II 2i^2.
Therefore, there is no correct option among the given choices (a, b, c, d, e, or f).
Learn more about Properties of exponents: brainly.com/question/3187898
#SPJ11
The expression II 2i^2 is equivalent to one of the given options: a, b, c, d, e, or f. To simplify the expression II 2i^2, we need to evaluate it using the properties of exponents.
First, let's rewrite 2i^2 as (2i)^2. Then, using the property (ab)^n = a^n * b^n, we can simplify further:
(2i)^2 = 2^2 * (i)^2 = 4 * i^2.
Now, we need to determine the value of i^2. Since the options don't provide information about i, we can assume it is a constant. Therefore, i^2 is a constant value.
Looking at the given options, we can see that none of them match the simplified expression 4 * i^2. Therefore, none of the provided options is equal to II 2i^2.
Therefore, there is no correct option among the given choices (a, b, c, d, e, or f).
Learn more about Properties of exponents: brainly.com/question/3187898
#SPJ11
Example 3: A wide rectangular channel with a manning number of 0.02 coveys a discharge of 3m3/s/m. There are two long reaches with different bed slopes. The first reach (upper) has a slope of 1:20 while that for the second reach (lower) is 1:800. Determine: a) The normal depth of flow on each reach b) Critical depth of flow c) Whether a hydraulic jump will occur. d) The conjugate depths of a jump occurred on the lower reach e) The energy head and the power lost in the jump
The normal depth of flow on the upper reach is 1.53 m and on the lower reach is 4.18 m.
The critical depth of flow on the upper reach is 1.99 m and on the lower reach is 7.72 m.
How to calculate the depth of flowTo calculate depth of flow
We are given the following data:
Discharge (Q) = 3 [tex]m^3/s/m[/tex]
Manning's roughness coefficient (n) = 0.02
Upper reach bed slope (S1) = 1:20
Lower reach bed slope (S2) = 1:800
Normal Depth:
Normal depth can be calculated using the Manning's equation for uniform flow as
[tex]Q = 1/n A(y)^2/3 S^1/2[/tex]
where A is the cross-sectional area of flow and S is the bed slope.
For the upper reach
S1 = 1/20 = 0.05
Area of flow[tex](A_1) = Q / (n S1 yn^2/3) = (3) / (0.02 * 0.05 * yn^2/3)[/tex]
The hydraulic radius (R₁) in terms of depth (y₁) is given by
[tex]R_1 = A_1 / P_1 = (Q / (n S_1 yn^2/3)) / (2 yn / 0.5) = (3 / (0.02 * 0.05 * yn^2/3)) / (4 yn / 0.5)[/tex]
yn₁ = 1.53 m
For the lower reach
S₂ = 1/800 = 0.00125
Area of flow[tex](A_2) = Q / (n S_2 yn^2/3) = (3) / (0.02 * 0.00125 * yn^2/3)[/tex]
The hydraulic radius (R2) in terms of depth (y2) is given by
[tex]R_2 = A_2 / P_2 = (Q / (n S_2 yn^2/3)) / (2 yn / 2) = (3 / (0.02 * 0.00125 * yn^2/3)) / (2 yn / 2)[/tex]
yn₂ = 4.18 m
Thus, the normal depth of flow on the upper reach is 1.53 m and on the lower reach is 4.18 m.
Critical Depth:
Critical depth can be calculated using the following equation:
[tex]yc = (Q^2 / g S)^1/3[/tex]
where g is the acceleration due to gravity.
For the upper reach
[tex]yc_1 = (3^2 / (9.81 * 0.05))^(1/3) = 1.99 m[/tex]
For the lower reach
[tex]yc_2 = (3^2 / (9.81 * 0.00125))^(1/3) = 7.72 m[/tex]
Hence, the critical depth of flow on the upper reach is 1.99 m and on the lower reach is 7.72 m.
Hydraulic Jump:
It can calculated using the following equation:
[tex]Fr = V / (g yn)^1/2[/tex]
where V is the velocity of flow.
For the upper reach
[tex]V_1 = Q / A1 = (3) / ((0.02 * 0.05 * 1.53^2/3)) = 2.74 m/s[/tex]
[tex]Fr_1 = V1 / (g yn1)^1/2 = 2.74 / (9.81 * 1.53)^1/2 = 0.59[/tex]
Since Fr1 is less than 1, a hydraulic jump will not occur on the upper reach.
For the lower reach, the velocity can be calculated as
[tex]V_2 = Q / A2 = (3) / ((0.02 * 0.00125 * 4.18^2/3)) = 5.93 m/s[/tex]
[tex]Fr_2 = V2 / (g yn2)^1/2 = 5.93 / (9.81 * 4.18)^1/2 = 1.34[/tex]
Since Fr2 is greater than 1, a hydraulic jump will occur on the lower reach.
Conjugate Depths of Jump:
The conjugate depths of the jump (y₁ and y₂) can be calculated using the following equations:
[tex]y_1 = yc^2 / (4 yn2)\\y_2 = 2.5 yn2 - 1[/tex]
Substituting the values
[tex]y_1 = (7.72^2) / (4 * 4.18) = 4.47 m\\y_2 = 2.5 * 4.18 - 1 = 9.45 m[/tex]
Therefore, the conjugate depths of the jump are 4.47 m and 9.45 m.
Energy Head and Power Loss in Jump:
The energy head before and after the jump can be calculated as
[tex]E_1 = y_1 + V_1^2 / (2g)\\E_2 = y_2 + V_2^2 / (2g)[/tex]
Substituting the values
[tex]E_1 = 4.47 + (2.74^2) / (2 * 9.81) = 5.58 m\\E_2 = 9.45 + (5.93^2) / (2 * 9.81) = 12.78 m[/tex]
The energy head lost in the jump is:
ΔE = E₁ - E₂2 = 5.58 - 12.78 = -7.20 m
Since the energy head is lost, the power loss in the jump can be calculated as
P = ΔE × Q = -7.20 × 3 = -21.6 kW
Therefore, the energy head lost in the jump is 7.20 m and the power loss is 21.6 kW.
Learn more on hydraulic jump on https://brainly.com/question/28507220
#SPJ4
"
The band is breaking up and Rob, Sue, Tim and Vito each want the tourbus. Using the method of sealed bids, Rob bids $2500, Sue bids$5400, Tim bids $2400, and Vito bids $6200 for the bus. SinceVito'
Rob will receive approximately $1133.33 from Vito.
To determine how much money Rob will get from Vito, we need to calculate the fair division of the bids among the four individuals. Since Vito won the bus with the highest bid, he will compensate the others based on their bids.
The total amount of compensation that Vito needs to pay is the sum of all the bids minus the winning bid. Let's calculate it:
Total compensation = (Rob's bid + Sue's bid + Tim's bid) - Vito's bid
= ($2500 + $5400 + $2400) - $6200
= $10300 - $6200
= $4100
Now, we need to determine the amount of money each person will receive. To calculate the fair division, we divide the total compensation by the number of people (4) excluding Vito, since he won the bid.
Rob's share = (Rob's bid) - (Total compensation / Number of people)
= $2500 - ($4100 / 3)
≈ $2500 - $1366.67
≈ $1133.33
Thus, the appropriate answer is approximately $1133.33 .
Learn more about money:
https://brainly.com/question/24373500
#SPJ11
State and explain the three main steps in a chain reaction.
Overall, the three main steps in a chain reaction—initiation, propagation, and termination—work together to sustain and regulate the reaction. The initiation step starts the reaction, the propagation step continues the reaction through the generation of new reactive species, and the termination step stops the reaction by removing or neutralizing the reactive species. Understanding and controlling these steps is crucial in various chemical and nuclear processes.
In a chain reaction, which is a self-sustaining process that occurs in certain chemical reactions or nuclear reactions, there are typically three main steps: initiation, propagation, and termination.
1. Initiation:
The initiation step involves the generation of reactive species, such as free radicals or excited molecules, that are highly reactive and capable of initiating the chain reaction. This step often requires an external source of energy, such as heat, light, or the collision of particles. For example, in a radical chain reaction, initiation occurs when a molecule is broken down into two or more highly reactive radicals through the absorption of energy. This step sets the chain reaction in motion.
2. Propagation:
Once the chain reaction is initiated, the propagation step takes place. During this step, the reactive species generated in the initiation step react with other molecules, producing new reactive species. These newly formed reactive species then go on to react with additional molecules, propagating the chain reaction. In a chain reaction, each reactive species produced in the propagation step serves as a precursor to the formation of more reactive species, resulting in a self-perpetuating process.
3. Termination:
The termination step is the final stage of a chain reaction. It involves the removal or deactivation of the reactive species responsible for propagating the reaction. This can occur through various mechanisms, such as two reactive species colliding and neutralizing each other or a reactive species reacting with an inert species or a scavenger molecule. Termination prevents the continuous propagation of the chain reaction and brings the reaction to an end.
To know more about reaction visit:
brainly.com/question/30464598
#SPJ11
Do public bodies have the unlimited right to determine which offeror is the "lowest responsible bidder"? Group of answer choices
A. Public bodies have the absolute right and discretion to award contracts for construction which are in the best interests of the taxpayers.
Public bodies do not have the unlimited right to determine which offeror is the "lowest responsible bidder".
Instead, public bodies have the absolute right and discretion to award contracts for construction which are in the best interests of the taxpayers. They are responsible for ensuring that they comply with the law and regulations when determining which offeror is the lowest responsible bidder.
What is the principle of the lowest responsible bidder?
The lowest responsible bidder principle states that the lowest bidder who can demonstrate their capability of effectively fulfilling all contractual responsibilities is awarded the contract.
It refers to the offeror who can offer the best value for money while still meeting the requirements of the tender specifications.
However, the public body cannot simply award the contract to the lowest bidder without determining whether they are responsible for meeting all of the requirements of the contract.
In this regard, the public body may consider a number of factors such as the offeror's experience, capacity, and financial capability when determining whether they are responsible enough to be awarded the contract.
It is essential to note that the public body should comply with all laws, regulations, and requirements when determining the lowest responsible bidder.
This is because they are responsible for ensuring that taxpayer dollars are used in the best interests of the public, and awarding contracts to offerors who are not capable of meeting their contractual obligations can lead to waste, fraud, or abuse of public funds.
To know more about lowest responsible bidder visit:
https://brainly.com/question/14816381
#SPJ1
You have $450. 00 each month to pay off these two credit cards. You decide to pay only the interest on the lower-interest card and
the remaining amount to the higher interest card. Complete the following two tables to help you answer questions 1-2.
Higher-Interest Card (Payoff Option)
1
$1,007. 24
$8. 23
$447. 73
Month
Principal
Interest accrued
Payment (on due
date)
End-of-month
balance
Lower-Interest Card
Month
Principal
Interest accrued
Payment (on due
date)
End-of-month
balance
$567. 74
1
$445. 81
$2. 27
$2. 27
$445. 81
2
$567. 74
2
$445. 81
3
3
5
5
The payment for the higher-interest card was calculated by subtracting the interest accrued from the total amount available for payments ($450.00), which left a remainder of $441.77 to be applied towards the principal.
Higher-Interest Card (Payoff Option)
Month Principal Interest accrued Payment (on due date) End-of-month balance
1 $1,007.24 $8.23 $441.77 $573.70
Lower-Interest Card
Month Principal Interest accrued Payment (on due date) End-of-month balance
1 $567.74 $2.27 $8.23 $562.78
2 $562.78 $2.25 $8.23 $557.80
3 $557.80 $2.23 $8.23 $552.83
4 $552.83 $2.21 $8.23 $547.87
5 $547.87 $2.19 $8.23 $542.91
Note: The payment for the higher-interest card was calculated by subtracting the interest accrued from the total amount available for payments ($450.00), which left a remainder of $441.77 to be applied towards the principal.
Learn more about interest. from
https://brainly.com/question/25720319
#SPJ11