some materials feel colder than others because...

The current I in the circuit will be 12A.

To calculate the current flowing in the circuit, we can use Ohm's law, which states that current is directly proportional to voltage and inversely proportional to resistance.

The total current flowing in the circuit is therefore given by Ohm's Law as:

I = V/R

where V is the voltage applied to the circuit and R is the total resistance of the two windings.

In this case, given that the voltage applied is 240V and the total resistance of the two windings is 20 ohms, the total current flowing in the circuit is given by:

I = 240/20 = 12A.

In other words, when two motor windings are connected in parallel and a voltage of 240V is applied, the current flowing in the circuit is 12A.

To know more about current, refer here:

https://brainly.com/question/17013740#

#SPJ4

The coefficient of static friction, μs, between the tires and the road needs to be greater than the centripetal acceleration divided by the gravitational acceleration.

In this case, the centripetal acceleration can be calculated as ac = [tex](v^2)/r[/tex], where v is the speed and r is the radius of the curve. Therefore, the required coefficient of static friction μs = ac/g, where g is the gravitational acceleration, should be greater than μs = [tex](121 km/h)^2[/tex] / (150m) / [tex]9.81m/s^2[/tex] ≈ 0.93.

This means that the coefficient of static friction should be greater than 0.93 in order for the car to be able to round a level curve of radius 150 m at a speed of 121 km/h. This coefficient of static friction is necessary to counteract the centripetal force, allowing the car to round the curve without slipping.

If the coefficient of static friction is not large enough, the car will not be able to round the curve at the speed specified.

For more such questions on Coefficient of static friction.

https://brainly.com/question/13828735#

#SPJ11

The current I(r) at a time after 1*r equals the time constant r is roughly 0.065 A. About 0.105 A is the current I(3r) at a point three times the time constant after 3*r.

Electric current (I) flowing through a circuit directly relates to its potential difference (V). When the potential difference is 60 volts, the electric current is 1.5 amps.

The following equations can be used to calculate the current in the RL circuit based on the information provided:

An RL circuit's current is determined by:

I(t) = (V/R) * (1 - e(-t/r))

The following queries can be resolved using this equation:

Question 1:

Add t = r to the equation as follows:

I(r) = (V/R) * (1 - e(-r/r))

I(r) = (V/R) * (1 - e(-1))

I(r) = (12.0/150) * (1 - e(-1))

I(r) ≈ 0.065 A

As a result, the current I(r) at a time after 1*r equals the time constant r is approximately 0.065 A.

Question 2:

What time is it now, I(3r), after 3*r, which is three times the time constant?

In the following equation, substitute t = 3r:

I(3r) = (V/R) * (1 - e(-3))

I(3r) = (12.0/150) * (1 - e(-3))

I(3r) ≈ 0.105 A

As a result, the current I(3r) at a time three times the time constant after 3*r is about 0.105 A.

Question 3:

After some time, the circuit's current will begin to approach a constant value, I. (as t tends to infinity). Who am I?

The exponential term e(-t/r) approaches 0 as t approaches infinity, and the current becomes:

I∞ = V/R

Substitute V = 12.0 V and R = 150 Ω into the equation:

I∞ = 12.0/150

I∞ = 0.08 A

As a result, after some time, the circuit's current will stabilize around 0.08 A.

To know more about current visit:-

https://brainly.com/question/15632994

#SPJ1

Question:

After the switch is closed, the current in the circuit grows over time approaching a constant value. In general, at time after a voltage source is connected to an RL circuit, the current I(t) in the circuit is given by the expression

1(t)=(1-e); where r = L/R

where & is the voltage provided by the battery, R is the resistance of the resistor, and r is the time constant characteristic of the circuit.

Growth of current in an RL circuit

Consider an R-L circuit as shown in the figure. The battery provides 12.0 V of voltage. The inductor has inductance L, and the resistor has resistance R = 150 . The switch is initially open as shown. At time r=0, the switch is closed. At time / after 0 the current /(1) flows through the circuit as indicated in the figure.

Question 1:

What is the current (r) at a time after 1-0 equal to time constant?

Question 2:

What is the current /(3r) at a time after 1-0 equal to three times the time constant?

Question 3:

The current in the circuit will approach a constant value / after a long time (as / tends to infinity). What is I.?

The length of the string is 0.48 m.

The length of the string of a pendulum is determined by the period, which is the time it takes for the pendulum to swing back and forth once.

String length = (Gravitational acceleration x (Period)2) / (4π2)

Where Gravitational acceleration is the acceleration due to gravity, which is 9.8 m/s2, and Period is the time it takes the pendulum to swing back and forth once.

The period is 10 seconds divided by 15 swings, or 0.67 seconds.

String length = (9.8 m/s2 x (0.67 s)2) / (4π2) = 0.48 m.

Therefore, the length of the string is 0.48 m.

to know more about string refer here:

https://brainly.com/question/30099412#

#SPJ11

The normal force on the rock at point B due to the bottom of the bowl is 4.08 N.

Given Data:

Mass of the rock, m = 0.25 kg

The radius of the bowl, r = 0.30 m

Speed of the rock, v = 2.8 m/s

Acceleration due to gravity, g = 9.81 m/s²

So, the Normal force on the rock due to the bottom of the bowl can be calculated as:

N = mg - m(v²/r)

Putting the values of given data, we get:

N = (0.25 kg)(9.81 m/s²) - (0.25 kg)(2.8 m/s)²/(0.30 m)N = 2.45 N - 6.53 NN = 4.08 N

Approximately, N = 4.08 N

Thus, the normal force on the rock at point B due to the bottom of the bowl is 4.08 N.

To know more about normal force click here:

https://brainly.com/question/30436126

#SPJ11

The work done in moving a particle from P to Q if the magnitude and direction of the force are given by v = 3i - 6j is 24 Joules.

The work done in moving a particle from P to Q if the magnitude and direction of the force are given by v = 3i - 6j can be found using the dot product formula:

[tex]W = \vec F \cdot \vec d[/tex]

where, [tex]\vec F[/tex] is the force, and d is the displacement vector from P to Q.

The coordinates of point P and Q is (-2, 9) and (-12, 8).

So, we need to find the displacement vector from P to Q.

[tex]d = (-12-(-2))\hat i, (8 - 9)\hat j[/tex]

[tex]d = (-10\hat i - 1\hat j)[/tex]

Work done in moving a particle from P to Q is:

[tex]W = \vec F \cdot \vec d[/tex]

Where [tex]F = 3\hat i - 6\hat j[/tex] and [tex]d = (-10\hat i - 1\hat j)[/tex].

[tex]W = (3\hat i - 6\hat j) . (-10\hat i - \hat j)W = -30 + 6[/tex]

W = - 24 Joules

the negative sign indicates work done is in the opposite direction of motion.

Therefore, the work done in moving a particle from P to Q if the magnitude and direction of the force are given by v = 3i - 6j is 24 Joules.

Learn more about work done:

https://brainly.com/question/18762601

#SPJ11

The solar system's many small bodies, such as asteroids, comets, and small moons, are unlikely as potential homes to life due to the fact that these celestial objects have too little gravity to support an atmosphere and most have no liquid water.

This is because their small sizes and masses do not allow for enough gravitational force to retain an atmosphere, and the extreme temperatures make liquid water impossible. Additionally, many small bodies lack the necessary components needed to support life, such as organic compounds or the right amount of radiation.

Asteroids, comets, and small moons typically have a low density, which means they are composed of rocks, dust, or ice, which would not support life. Moreover, these celestial objects have highly variable rotational periods and orbits, which would result in chaotic and extremely variable temperatures, making it difficult for any life forms to survive.

These celestial objects are also very small in comparison to other bodies in the solar system, meaning they receive far less sunlight than larger bodies. This is important for life to thrive because it requires energy from the sun to grow, reproduce, and obtain nutrients. The lack of energy from the sun, combined with the lack of liquid water and a protective atmosphere, makes these small bodies unlikely candidates for supporting life.

Therefore, it is unlikely to consider the celestial objects as potential homes because of the lack of sustainable living conditions like gravity, water, oxygen, and other organic substances.

To know more about asteroids, refer here:

https://brainly.com/question/19161842#

#SPJ11

The gravitational area close to the floor of Mercury is 3.70 N/kg. The gravitational area close to the floor of Venus is 8.87 N/kg.

For Mercury:

g = (6.6743 × 10^-11 N m²/kg²) x (3.29E23 kg) / (2.44E6 m)²

g = 3.70 m/s²

The gravitational area close to the floor of Mercury is 3.70 N/kg.

For Venus:

g = (6.6743 × 10^-11 N m^2/kg²) * (4.87E24 kg) / (6.05E6 m)²

g = 8.87 m/s²

The gravitational area close to the floor of Venus is 8.87 N/kg.

Venus is a planet in our solar device, named after the Roman goddess of love and splendor. From a physics angle, Venus is an interesting object to look at because of its proximity to Earth and its specific characteristics.

Venus is the second one planet from the sun and is similar in size and composition to Earth. but, its environment is a lot thicker, with a high awareness of carbon dioxide and sulfuric acid. the intense greenhouse effect due to this thick surroundings makes Venus the hottest planet within the sun machine, with surface temperatures reaching over 460 degrees Celsius. Physicists study Venus to better apprehend planetary atmospheres, greenhouse consequences, and weather dynamics.

To know more about Venus visit here:

brainly.com/question/10601018

#SPJ4

Frictional forces between a liquid and the walls of a pipe can convert kinetic energy into thermal energy, leading to a drop in pressure within the pipe due to the decrease in force being applied to the walls.

Frictional forces between the liquid and the walls of a pipe can lead to the conversion of kinetic energy into thermal energy. This can have an effect on the pressure of the liquid within the pipe. Specifically, when the liquid loses kinetic energy due to friction, the pressure within the pipe drops. This drop in pressure can be attributed to the fact that as the liquid loses kinetic energy, its molecules move more slowly, thus decreasing the amount of force that is being applied to the walls of the pipe. As a result, the pressure within the pipe decreases.

In summary, frictional forces between a liquid and the walls of a pipe can convert kinetic energy into thermal energy, leading to a drop in pressure within the pipe due to the decrease in force being applied to the walls.

For more such questions on Frictional forces.

https://brainly.com/question/30280752#

#SPJ11

The oscillation frequency is 1.3294 Hz.

Given that,

Mass of harmonic oscillator, m = 0.25 kg

Total mechanical energy, E = 0.35 J

Oscillation amplitude, A = 0.01 m

To find out the oscillation frequency, we can use the formula;

Total mechanical energy of a simple harmonic oscillator is the sum of the kinetic energy and potential energy of the oscillator.

Hence,

E = K + PE.

Where,

K = 1/2mv² is the kinetic energy of the oscillator,

PE = 1/2kA² is the potential energy of the oscillator.

The frequency of the oscillator is given by the equation: f = 1/(2π) √k/m

From the given data,

We can find out the force constant, k from the potential energy equation,

k = 2PE/A²

 = 2 * 0.35 J/0.01²

m² = 70 J/m

Substituting the values of m and k, we can find out the frequency.

f = 1/(2π) √k/m

 = 1/(2π) √70/0.25

 = 1/(2π) √280/4

= 1/(2π) √70/1= 1/(2π) * 8.3666

= 1.3294 Hz

For similar question on frequency.

https://brainly.com/question/254161

#SPJ11

The tension in the vine if a monkey climbs a vine at a constant speed is 0 Newton.

The magnitude of tension force depends on the amount of force applied to the ends of the string or rope, as well as the properties of the string or rope itself, such as its length, thickness, and elasticity.

Tension force is often used in mechanical systems to transfer forces or transmit power. For example, a cable used to lift a heavy object will experience tension forces as it resists the weight of the object. Similarly, a belt in a car engine experiences tension forces as it transfers power from the engine to the wheels.

Mass of the monkey, m = 20 kg.

Let the tension in the vine be T.

The acceleration of the monkey is zero since the speed is constant.

Using the second law of motion,F = ma

Here, acceleration, a = 0F = 0N = ma= 20 x 0= 0 N

Tension in the vine is zero.

To learn more about tension:

https://brainly.com/question/13397436#
#SPJ11

The two regions of the electromagnetic spectrum where the earth's atmosphere is transparent (radiation can get in) are visible light and ultraviolet radiation.

The electromagnetic spectrum is a range of electromagnetic waves, which includes visible light, gamma rays, X-rays, ultraviolet light, microwaves, radio waves, and infrared radiation. The range of frequencies that electromagnetic radiation encompasses is referred to as the electromagnetic spectrum.

The earth's atmosphere is transparent to radiation in two regions of the electromagnetic spectrum: visible light and ultraviolet radiation. The following are some of the features of visible light: It is a region of the electromagnetic spectrum that is visible to the human eye. Because of its wavelength, visible light is seen as a color. It has a wavelength of 400-700 nm, and it is approximately 10-7 meters long.

The following are some of the characteristics of ultraviolet radiation: The electromagnetic radiation's frequency is higher than that of visible light. Ultraviolet radiation has a wavelength of 10-8-10-7 meters.

If light can travel through something and everything behind it is clearly visible, it is said to be transparent. A transparent object enables light to pass through it without being diffused.

To know more about ultraviolet radiation:

https://brainly.com/question/29762547

#SPJ11

Jumping off a floating canoe towards a dock may not be as simple as it appears due to the reaction force created by the canoe's displacement of water. Therefore, it's important to exercise caution and consider the various factors that could impact the jump's outcome. This phenomenon is known as the "reaction force," which is equal and opposite to the force exerted by the canoe on the water.

When you jump off the canoe, you create a force that pushes you forward towards the dock, but the water's reaction force pushes you backward, causing you to fall into the water instead. When you jump from the front of a floating canoe towards a dock, you might expect to land on the dock effortlessly.

Moreover, the instability of the canoe on the water surface, the angle and velocity at which you jump, the distance between the canoe and the dock, and the depth of the water could all affect the outcome of your jump. Therefore, it is crucial to take into account these factors before jumping off a floating canoe.

Know more about force here:

https://brainly.com/question/26115859

#SPJ11

The speed of the 2.2 g ping pong ball must be 3.43 m/s in order for it to have the same kinetic energy as the 7.0 kg bowling ball moving at 2.20 m/s

To calculate the speed of the 2.2 g ping pong ball so that it has the same kinetic energy as the 7.0 kg bowling ball moving at 2.20 m/s, use the equation KE = 1/2 mv2, where m is mass and v is speed.

Rearrange the equation to v = √(2KE/m).

Substituting the given values, we get:

v = √(2 * (1/2 * 7.0kg * 2.20m/s2) / 2.2g)

v = 2.20 m/s

Therefore, the speed of the 2.2 g ping pong ball has the same kinetic energy as the 7.0 kg bowling ball moving at 2.20 m/s.

To know more about kinetic energy click here:

https://brainly.com/question/15764612

#SPJ11

The maximum acceleration of the particle is 1780 cm/s^2.

The maximum acceleration of a particle in simple harmonic motion is equal to the product of the angular frequency squared (ω^2) and the amplitude (A).

The angular frequency can be calculated from the given frequency as follows:

[tex]ω = 2πf = 2π(3.0 Hz) ≈ 18.85 rad/s[/tex]

Therefore, the maximum acceleration of the particle is:

[tex]a_max = ω^2A = (18.85 rad/s)^2(5.0 cm)[/tex]

[tex]a_max = 1780 cm/s^2[/tex]

Learn more about acceleration of a particle at: https://brainly.com/question/20164286

#SPJ11

Answer:

A. ionization electron

A person whose weight is 509n is being pulled up vertically by a rope from the bottom of a cave that is 33.1m deep. the maximum tension that a rope can withstand without breaking is 571n. The shortest time to bring the person out of the cave, starting from rest is: 3.74 seconds, this time is determined by the tension of the rope and the acceleration due to gravity.

The shortest time to bring a person whose weight is 509n out of a 33.1m deep cave is determined by the maximum tension that the rope can withstand without breaking.

First, calculate the total weight of the person plus the rope tension: 509n + 571n = 1080n.
Second, calculate the acceleration due to gravity (g): g = 1080n / 33.1m = 32.6 m/s^2.
Third, calculate the acceleration time: t = √ (2 * 33.1m) / 32.6 m/s^2 = 3.74 seconds.

Therefore, the shortest time to bring the person out of the cave is 3.74 seconds, starting from rest. This time is determined by the tension of the rope and the acceleration due to gravity.

To know more about tension refer here:

https://brainly.com/question/29869473#

#SPJ11

The equivalent resistance of resistors in series is always greater than the individual resistances. This is because the total resistance of the circuit is the sum of the resistances, and therefore the electric current has to overcome more resistance to flow through the circuit as compared to when a single resistor is used.

To find the equivalent resistance, req, of two resistors in series, r1 and r2, the following equation is used:

Req = R1 + R2

Where Req is the equivalent resistance of the series circuit,

R1 is the resistance of the first resistor,

R2 is the resistance of the second resistor.

Resistors in a circuit are the components that oppose the flow of electric current. When two resistors are connected in series, they are connected end to end so that the electric current flows through one resistor before flowing through the second one.In a series circuit, the equivalent resistance, req, is calculated as the sum of the individual resistances of the resistors connected in series.

Therefore, to find the equivalent resistance of two resistors in series, R1 and R2, we add the resistance values of the two resistors, as shown in the formula above.

for such more question on equivalent resistance

https://brainly.com/question/1851488

#SPJ11

The value of the acting force between the two coils is approximately 5.65 N.

F = (μ₀/4π) * (2I₁I₂*l)/d

Substituting these values into the method, we get:

F = (4π × [tex]10^{-7}[/tex] T·m/A) * (230 A30 A*π m)/(0.05 m)

Simplifying the expression, we get:

F ≈ 5.65 N

Force is an agent that can change the state of motion or shape of an object. it is a vector amount that has both value and path. Force can be applied through direct contact or from a distance, such as through gravitational or electromagnetic fields. Pressure is measured in gadgets of newtons (N) inside the international gadget of units (SI). Some common examples of forces include friction, tension, gravity, and electromagnetic forces.

According to Newton's laws of motion, force is directly proportional to the rate of change of momentum of an object. This means that a larger force will cause a greater acceleration of an object, and a smaller force will cause a smaller acceleration. Understanding the concept of force is essential to many areas of physics, including mechanics, thermodynamics, and electromagnetism.

To learn more about Force visit here:  

brainly.com/question/30526425

#SPJ4

The scale will read 708.2 kg during the acceleration.

This is because during the acceleration, the hoisting cable applies a force of 9300 N to the elevator. This force is equal to the sum of the masses of the woman and the elevator multiplied by the acceleration.

Since the combined mass of the elevator and the woman is 816 kg, the force is equal to 816 kg multiplied by the acceleration. Therefore, the scale will read the sum of the woman's mass (61.8 kg) and the elevator's mass (746.2 kg) multiplied by the acceleration. Therefore, the scale will read 708.2 kg during the acceleration.

In conclusion, the scale will read 708.2 kg during the acceleration because the hoisting cable applies a force equal to the sum of the masses of the woman and the elevator multiplied by the acceleration. This force is applied to the elevator, and the scale will read the sum of the woman's mass and the elevator's mass multiplied by the acceleration.

Know more about acceleration here

https://brainly.com/question/12550364#

#SPJ11

The distance 'd' of the equation represents the distance between the two slits, A and B. This is because the equation is for the double-slit experiment, which is based on two narrow slits acting as wave sources.

This is the distance between the two sources that act as wave sources, which interfere with each other to create the diffraction patterns C, D, E, and F. The light bands between D and E and F are not part of the equation and do not represent the 'd' of the equation.

The equation: λ/d = x/L represents the image form between A and B.  This distance is used in the equation to calculate the angle of diffraction.

Diffraction is the process by which light or sound waves bend around corners or obstacles and spread out when passing through narrow openings.

To learn more about diffraction click here https://brainly.com/question/12290582

#SPJ1

complete question: The image below is a sketch of two-slit diffraction of light. Narrow slits at A and B act as wave sources, and waves interfering in various phases are shown at C, D, E, and F.

A sketch of two-slit diffraction of light. Narrow slits at A and B act as sources on the left, and waves interfering in various phases are shown at C, D, E, and F on the right.

The equation for the double-slit experiment for small angles is  λ/d = x/L

In the image, which description below represents the d of the equation?

The distance between A and B

The distance between A and D

The distance between midpoints D, E, and F

The light bands between D and E and F

Answer: the correct answer is; the distance between A and B

Explanation:

I just took the test, and get it right

It shows that the orientation of the iolab that gives the largest "by" reading corresponds to the direction of the Earth's magnetic field in your location.

A magnetometer is a device that measures magnetic fields. It can be used to detect the Earth's magnetic field, which is generated by the motion of molten iron in the Earth's core. The Earth's magnetic field is a vector field, which means that it has both magnitude and direction.

When you stand several feet away from anything metallic or magnetic and point the y-axis of the iolab in different directions, you are essentially changing the orientation of the magnetometer sensor relative to the Earth's magnetic field. The sensor measures the strength of the magnetic field component in the direction of the sensor. In this case, you are only measuring the "by" component of the magnetic field, which is the component of the field that is perpendicular to the surface of the Earth.

By finding the orientation of the iolab for which its measurement of "by" has the biggest value, you are essentially finding the direction of the Earth's magnetic field in your location. The direction of the Earth's magnetic field at any point on the Earth's surface is not constant, and it varies with location. However, in general, the direction of the Earth's magnetic field at any point on the Earth's surface is roughly parallel to the surface of the Earth and points towards the geographic North Pole.

Therefore, the orientation of the iolab that gives the largest "by" reading corresponds to the direction of the Earth's magnetic field in your location.

Learn more about magnetic field on

https://brainly.com/question/14411049

#SPJ1

The electric field strength at the midpoint between a 7.6 nc point charge and a -2.6 nc point charge which are 3.1 cm apart is 279.8 N/C.

An electric field refers to a field surrounding a charged object, through which another charged object would feel a force. A charge placed in an electric field is subjected to a force depending on the charge and distance from the source of the field.

The electric field intensity or strength may be calculated using Coulomb's law by taking the charge 'Q' as a point charge and then determining the value of the electric field at a distance 'r' from the charge.

The magnitude of the electric field due to a point charge Q at a distance r is

E=kQ/r²,

where k is Coulomb's constant,

k=9×10⁹ Nm²/C².

So, the electric field at the midpoint is due to the combined effect of both charges. The charges are located 3.1 cm apart, so the midpoint is 1.55 cm from each of the charges. Therefore, we need to calculate the electric field due to each of the charges separately and add them up. The electric field at the midpoint due to a 7.6 nc point charge E₁=kQ₁/r₁²

  =(9×10⁹ Nm²/C²)(7.6×10⁻⁹ C)/(0.0155 m)²

  =294.47 N/C.

The electric field at the midpoint due to a -2.6 nc point charge

E₂=kQ₂/r₂²

   =(9×10⁹ Nm²/C²)(-2.6×10⁻⁹ C)/(0.0155 m)²

   =-14.67 N/C.

The net electric field at the midpoint is given by

E=E₁+E₂=294.47 N/C-14.67 N/C

 =279.8 N/C.

To know more about electric field:

https://brainly.com/question/26446532

#SPJ11

The answer are energy used by the 600-watt toaster for 6.0 min is 0.06 kWh (kilowatt-hours).

To solve the problem, we must first calculate the power of the toaster and the time it is in use. The toaster's power is given to be 600 watts, and the time it's in use is 6 minutes.

The formula for calculating energy is given below. Energy = Power x Time Energy = 600 x 6 Joules

Using the conversion factor, we can convert joules to kilowatt-hours (kWh).1 kWh = 3.6 x 10^6 J

Now, we can find out the energy used in kilowatt-hours.

Energy = 600 x 6 / (3.6 x 10^6) kWh Energy = 0.06 kWh

Hence, the energy used by the 600-watt toaster for 6.0 min is 0.06 kWh (kilowatt-hours).

To know more about kwh energy refer here:

https://brainly.com/question/15319126#

#SPJ11

The disorder of the eye is known as Myopia.

The medical term for this disorder is called “near-sightedness”. Myopia is a type of refractive error of the eye that causes distant objects to appear blurred while nearby objects remain in focus.

The eye’s ability to focus on objects at different distances is due to the refraction or bending of light as it passes through the eye’s cornea and lens. The light is then focused onto the retina, a layer of light-sensitive cells located at the back of the eye.

In the case of myopia, the eyeball is too long, and the lens or cornea is too curved, causing the light to come to a focus in front of the retina instead of directly on it. This leads to blurred vision when viewing distant objects.

There are many causes of myopia, including genetic factors, environmental factors, and lifestyle factors such as reading or working on a computer for prolonged periods. Myopia can also worsen over time if left untreated, which can lead to a higher risk of eye conditions such as cataracts, glaucoma, and retinal detachment.

Treatment for myopia includes corrective lenses such as glasses or contact lenses, refractive surgery, or orthokeratology, which involves using specially designed contact lenses to reshape the cornea overnight. Regular eye exams are important to diagnose and manage myopia to prevent complications and maintain healthy vision.

Therefore, the disorder of the eye in which the optic axis becomes too long, resulting in the light coming to a focus in front of the retina is Myopia or Near-sightedness.

To know more about Myopia, refer here:

https://brainly.com/question/28274668#

#SPJ11

The electric field 1.0 mm above the surface at a point near the center is 1.13 × 10⁵ [tex]\frac{N}{C}[/tex] . This is taken out by coulomb ' s law .

An electric field (also known as an E-field is a physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, attracting or repelling them. It also refers to the physical field of a charged particle system.

Electric fields play an important role in many fields of physics and are used in electrical technology. For example, in atomic physics and chemistry, the electric field is the attractive force that holds the atomic nucleus and electrons together in atoms. It is also the driving force behind chemical bonding between atoms, which results in molecules.

use formula E = σ /ε

to know more about electric field , visit ,

brainly.com/question/15800304

#SPJ1

In the following question, among the various parts to solve on visible spectrum.- A. Red light has a longer wavelength than violet light. B. Violet light has a higher frequency than red light. C. Violet light has greater energy than red light.

Violet and red light from the visible spectrum can be compared based on their wavelengths, frequencies, and energies. Violet light has a shorter wavelength, higher frequency, and greater energy than red light. The answers to the specific questions are: Which has the longer wavelength? Red light has a longer wavelength than violet light. Which has the greater frequency? Violet light has a higher frequency than red light. Which has the greater energy? Violet light has greater energy than red light. An HTML-formatted answer would look like this:

Violet and red light from the visible spectrum can be compared based on their wavelengths, frequencies, and energies. Violet light has a shorter wavelength, higher frequency, and greater energy than red light. The answers to the specific questions are:

For more such questions on visible spectrum.

https://brainly.com/question/30138070

#SPJ11

When an elevator is descending at a constant velocity, the forces acting on it can be represented by two force vectors on a free-body diagram.

A free-body diagram (FBD) is a graphical representation of the forces acting on a system. They are:

Gravity force or weight force: This force vector acts downward and is equal to the weight of the elevator. This force is determined by the mass of the elevator and the acceleration due to gravity.

Tension force: This force vector acts upward and is equal to the force exerted by the cable that suspends the elevator. This force is equal in magnitude to the weight force but in the opposite direction.

The system’s internal and external forces, as well as its forces of interaction with other systems, are all included in the FBD. It is essential to understand these forces before solving a physics problem.

To know more about force vectors:

https://brainly.com/question/13492374

#SPJ11

The following is true about a comet that is on an elliptical orbit around the sun is b. The comet's speed is greatest when it is nearest the sun.

A comet is an object in space with a visible coma or atmosphere, along with a "tail" that can extend for millions of miles through space. A comet's orbit is elliptical or oval-shaped; that is, it is more elliptical or oval-shaped than a planet's or moon's orbit.

As a result, when it approaches the sun, its velocity increases.When the comet is closest to the sun, its speed is greatest. This is due to the fact that as a comet travels closer to the sun, it falls under the sun's gravitational pull, causing its speed to increase. As a result, the comet's velocity at its closest approach to the sun is the highest.

Learn more about comet at:

https://brainly.com/question/12443607

#SPJ11

The vertical component of the tension is 1,177.05 N while the horizontal component of the tension is 127.47 × 3.90² = 1,949.04 N.

The magnitude of the centripetal acceleration is 2.14 m/s².

A) The vertical component of the tension equals the weight it supports, which is the weight of the person plus the weight of the basket:

Weight = (82.0 kg + 45.0 kg) × 9.81 m/s²

Weight = 1,177.05 N

Therefore, the vertical component of the tension is 1,177.05 N.

To find the horizontal component of the tension, we can use the fact that the net force in the horizontal direction is zero when the basket is moving at a constant speed.

The only horizontal force is the component of the tension perpendicular to the radius, so:

The horizontal component of tension = centripetal force

Horizontal component of tension = (mass × centripetal acceleration)

Horizontal component of tension = (82.0 kg + 45.0 kg) × (v²/7.10 m)

Horizontal component of tension = 127.47 v² N

Setting these two components equal to each other gives:

1,177.05 N = 127.47 v² N

Solving for v gives:

v = 3.90 m/s

Therefore, the horizontal component of the tension is 127.47 × 3.90² = 1,949.04 N.

B) The centripetal acceleration is given by:

a = v²/r

a = (3.90 m/s)²/7.10 m

a = 2.14 m/s²

Therefore, the magnitude of the centripetal acceleration is 2.14 m/s².

C) The speed of the basket and its passenger is 3.90 m/s.

D) The time it takes the basket to make one complete circle is given by:

T = 2πr/v

T = 2π(7.10 m)/3.90 m/s

T = 12.9 s

Therefore, it takes the basket 12.9 s to make one complete circle.

Learn more about centripetal acceleration at: https://brainly.com/question/19246433

#SPJ1