Two points A (3, 36,, -4) and B (7, 150°, 3.5) are given in the cylindrical coordinate system. Find the distance between A and B.
To find the distance between A and B, we need to use the cylindrical coordinate system. The cylindrical coordinate system uses three parameters to describe a point in space: r, θ, and z, where r is the radius from the origin, θ is the angle from the positive x-axis in the xy-plane, and z is the distance from the xy-plane.
The distance formula in the cylindrical coordinate system is given as:$$D = \sqrt{(r_2^2 + r_1^2 - 2r_1r_2\cos(\theta_2 - \theta_1) + (z_2 - z_1)^2)}$$We can use this formula to find the distance between A and B as follows:
Given points are: A (3, 36°, -4)B (7, 150°, 3.5)The distance formula in the cylindrical coordinate system is given as:
$$D = \sqrt{(r_2^2 + r_1^2 - 2r_1r_2\cos(\theta_2 - \theta_1) + (z_2 - z_1)^2)}$$
Substituting the values of the given points:
$$D = \sqrt{((7)^2 + (3)^2 - 2(7)(3)\cos(150° - 36°) + (3.5 - (-4))^2)}$$
Simplifying, we get:$$D = \sqrt{(49 + 9 - 42\cos(114°) + 7.5^2)}
$$We know that $\cos(114°) = -\cos(180° - 114°) = -\cos(66°)$
So, substituting this value:$$D = \sqrt{(49 + 9 + 42\cos(66°) + 7.5^2)}$$
Using a calculator, we get:
$$D = \sqrt{622.432} \approx 24.96$$
Therefore, the distance between A and B is approximately 24.96 units.
to know more about coordinate system here:
brainly.com/question/4726772
#SPJ11
Which of the following routing protocols is not commonly used as an IGP? a. BGP b. EIGRP c. RIP d. OSPF
The correct answer is A . BGP (Border Gateway Protocol) is not commonly used as an Interior Gateway Protocol (IGP).
The correct answer is A. BGP is primarily used as an Exterior Gateway Protocol (EGP) to exchange routing information between different autonomous systems on the internet. It is used for routing between different organizations or internet service providers rather than within a single organization's internal network.
On the other hand, EIGRP (Enhanced Interior Gateway Routing Protocol), RIP (Routing Information Protocol), and OSPF (Open Shortest Path First) are commonly used as Interior Gateway Protocols (IGPs) within an organization's internal network to facilitate routing and exchange of routing information among routers.
Know more about Border Gateway Protocol here:
https://brainly.com/question/32373462
#SPJ11
After execution of the code fragment
class rectangle
{
public:
void setData(int, int); // assigns values to private data
int getWidth() const; // returns value of width
int getLength() const; // returns value of length
rectangle(); // default constructor
private:
int width; // width of the rectangle
int length; // length of the rectangle
};
// copies the argument w to private member width and l to private member length.
void rectangle::setData(int w, int l)
{
width = w;
length = l;
}
// returns the value stored in the private member width.
int rectangle::getWidth() const
{
return width;
}
// returns the value stored in the private member length.
int rectangle::getLength() const
{
return length;
}
// Default constructor.
rectangle::rectangle()
{
width = 0;
length = 0;
}
int main()
{
rectangle box1, box2, box3;
int x = 4, y = 7;
box1.setData(x,x);
box2.setData(y,x);
cout << box1.getWidth() + box1.getLength();
return 0;
}
what is displayed on the screen?
The expression `box1.getWidth() + box1.getLength()` evaluates to `4 + 4`, which is `8`. Therefore, the output displayed on the screen will be:
8
After execution of the code fragment class what is displayed on the screen?The code provided creates three instances of the `rectangle` class named `box1`, `box2`, and `box3`. It then sets the data for `box1` and `box2` using the `setData` function, passing `x` and `y` as arguments.
In the `main` function, `box1.getWidth()` returns the value stored in the private member `width` of `box1`, which is `4`. Similarly, `box1.getLength()` returns the value stored in the private member `length` of `box1`, which is also `4`.
The expression `box1.getWidth() + box1.getLength()` evaluates to `4 + 4`, which is `8`.
Finally, the `cout` statement outputs `8` to the screen.
Therefore, the output displayed on the screen will be:
8
Learn more about arguments
brainly.com/question/2645376
#SPJ11
Create a binary code for the representation of all the digits of the system of the previous exercise (0, 1, 2, 3, ..., r-1), with the property that the codes for any two consecutive digits differ only in one position bit. Specifies the minimum number of bits required to generate such code. The digit 0 must use a code where all its bits have a value of 1. Additionally, comment on whether under the aforementioned restrictions the code could be cyclical and the reason for said answer.
In order to create a binary code for the representation of all the digits of the system, the terms that must be included are digits, binary code, consecutive digits, bit, and a minimum number of bits. Here's the solution to the given problem: Given a system with r digits, the binary codes for the digits are created in such a way that the codes for any two consecutive digits differ only in one position bit.0 is represented using a code where all bits have a value of
1. Suppose there are 'n' bits used to represent each digit. Since any two consecutive digits differ only in one position bit, a minimum of n + 1 bits are required to represent r digits. This is because every extra digit requires a change in one of the previous codes, which can be achieved by changing only one of the position bits. If the number of bits was limited to n, it would not be possible to generate such codes without repetition, and the code for at least one digit would be identical to the code for some other digit with a different value.
Since any two consecutive digits differ only in one position bit, the code generated cannot be cyclical, since in a cycle there is a reversal of all the bits, but the change required is a single-bit shift. Therefore, the code generated is not cyclical.
to know more about binary code here:
brainly.com/question/28222245
#SPJ11
Question 1 Wood is converted into pulp by mechanical, chemical, or semi-chemical processes. Explain in your own words the choice of the pulping process. Question 2 The objective of chemical pulping is to solubilise and remove the lignin portion of wood, leaving the industrial fibre composed of essentially pure carbohydrate material. There are 4 processes principally used in chemical pulping which are: Kraft, Sulphite, Neutral sulphite semi-chemical (NSSC), and Soda. Compare the Sulphate (Kraft/ Alkaline) and Soda Pulping Processes. Question 3 Draw a well label flow diagram for the Kraft Wood Pulping Process that is used to prepare pulp.
The pulping process can be of a mechanical or chemical form. The mechanical form involves manually grinding the wood fibers until they are separated from each other. The chemical process uses solutions to remove the lignin from the wood fibers. The semi-chemical process involves chemical solution and manual separation.
Comparing the Sulphate (Kraft/ Alkaline) and Soda Pulping ProcessesThe sulfate process uses a mix of sodium hydroxide and sodium sulfide to decompose lignin and the end result is a purified wood substrate that can be used to produce pure paper.
The soda pulping process, on the other hand, only uses sodium hydroxide and the end result may not be as bright as that of the sulfate kraft process.
Learn more about soda pulping here:
https://brainly.com/question/28959723
#SPJ4
Define an array class template MArray which can be used as in the following main(). (Note: you are not allowed to define MArrax based on the templates in the C++ standard library). int main() #include #include { using namespace std; MArrax stringArray(2); stringArray [0] =____"string0"; stringArray [1] =___"string1"; MArrax stringArray1 = string Array; cout << intArray << endl:______// display: 0, 1, 4, 9, 16, cout<
The code defines a class template called 'MArray' for creating arrays of any type. It demonstrates creating instances of 'MArray' for integers and strings, assigning values, and displaying the array contents using 'cout'.
Here's an example of defining an array class template called 'MArray' and using it in the provided 'main()' function:
#include <iostream>
using namespace std;
template<typename T>
class MArray {
private:
T* elements;
int size;
public:
MArray(int size) {
this->size = size;
elements = new T[size];
}
T& operator[](int index) {
return elements[index];
}
friend ostream& operator<<(ostream& os, const MArray<T>& arr) {
for (int i = 0; i < arr.size; i++) {
os << arr.elements[i] << " ";
}
return os;
}
~MArray() {
delete[] elements;
}
};
int main() {
MArray<int> intArray(5);
intArray[0] = 0;
intArray[1] = 1;
intArray[2] = 4;
intArray[3] = 9;
intArray[4] = 16;
MArray<string> stringArray(2);
stringArray[0] = "string0";
stringArray[1] = "string1";
MArray<string> stringArray1 = stringArray;
cout << intArray << endl; // Display: 0 1 4 9 16
cout << stringArray1 << endl; // Display: string0 string1
return 0;
}
- The 'MArray' class template represents an array that stores elements of type 'T'.
- The class provides a constructor to initialize the array with a specified size.
- The 'operator[ ]' is overloaded to provide element access and assignment.
- The 'operator<<' is overloaded as a friend function to enable displaying the elements of the array using the output stream ('cout').
- The destructor deallocates the dynamically allocated array to prevent memory leaks.
- In the 'main()' function, an 'MArray' object is created for storing integers ('intArray') and strings ('stringArray').
- Elements are assigned values using the overloaded operator[ ]' .
- A new 'MArray' object ('stringArray1') is created as a copy of 'stringArray'.
- The contents of 'intArray' and 'stringArray1' are displayed using 'cout'.
Please note that this is a simplified implementation, and in practice, you may need to consider additional features and error handling.
To learn more about class template, Visit:
https://brainly.com/question/32355802
#SPJ11
Computer science PYTHON question.
Can you please help me modify these 2 programs. One of them (randomizer.py) generates a random number and the other one (roulette.py) uses the generated random number from the previous program to make a selection for the user.
The goal is to have the random number generated to be between from 0-38 (0-36 for the numbers in roulette, 37 for red, and 38 for black).
This is what I have so far:
Randomizer.py
import time
import math
class PseudoRandom:
def __init__(self):
self.seed = -1
self.prev = 0
self.a = 25214903917
self.c = 11
self.m = 2**31
def get_seed(self):
seed = time.monotonic()
self.seed = int(str(seed)[-3:]) # taking the 3 decimal places at the end of what is returned by time.monotonic()
def generate_random(self, prev_random, range):
"""
Returns a pseudorandom number between 1 and range.
"""
# if first value, then get the seed to determine starting point
if self.seed == -1:
self.get_seed()
self.prev = raw_num = (self.a * self.seed + self.c) % self.m
# use previous value to determine next number
else:
self.prev = raw_num = (self.a * prev_random + self.c) % self.m
return math.ceil((raw_num / self.m) * range)
if __name__ == "__main__":
test = PseudoRandom()
for i in range(10):
rand = test.generate_random(test.prev, 10)
print(rand)
Roulette.py
import randomizer
test = randomizer.PseudoRandom()
# color choose and roulette simulation
def simulate():
print("Choose a number between 0-36, Red, or Black:")
answer = input("> ")
result = random.generate_random
if result == 0 and answer == "0":
print("You bet on the number 0. Congrats you won!")
elif result == 1 and answer == "1":
print("You bet on the number 1. Congrats you won!")
#continue with the other results in roulette 2-36
elif result == 37 and answer == "Red":
print("You bet on Red. Congrats you won!")
elif result == 38 and answer == "Black":
print("You bet on Black. Congrats you won!")
else:
print("You lost!")
In "randomizer.py," the `generate_random` method now generates a number between 0 and the specified range.
In "roulette.py," the `simulate` function now uses the updated random number range (39) to make the selection for the user.
Here are the modified versions of the "randomizer.py" and "roulette.py" programs with the requested modifications:
randomizer.py:
```python
import time
import math
class PseudoRandom:
def __init__(self):
self.seed = -1
self.prev = 0
self.a = 25214903917
self.c = 11
self.m = 2**31 - 1
def get_seed(self):
seed = time.monotonic()
self.seed = int(str(seed)[-3:]) # taking the 3 decimal places at the end of what is returned by time.monotonic()
def generate_random(self, prev_random, rng):
"""Returns a pseudorandom number between 0 and rng."""
# if first value, then get the seed to determine starting point
if self.seed == -1:
self.get_seed()
# use previous value to determine next number
self.prev = raw_num = (self.a * self.seed + self.c) % self.m
# update seed for next iteration
self.seed = raw_num
return math.floor((raw_num / self.m) * rng)
if __name__ == "__main__":
test = PseudoRandom()
for i in range(10):
rand = test.generate_random(test.prev, 10)
print(rand)
```
roulette.py:
```python
import randomizer
test = randomizer.PseudoRandom()
# color choose and roulette simulation
def simulate():
print("Choose a number between 0-36, Red, or Black:")
answer = input("> ")
result = test.generate_random(test.prev, 39) # Generate random number between 0 and 38
if result == 0 and answer == "0":
print("You bet on the number 0. Congrats, you won!")
elif result >= 1 and result <= 36 and answer == str(result):
print(f"You bet on the number {result}. Congrats, you won!")
elif result == 37 and answer == "Red":
print("You bet on Red. Congrats, you won!")
elif result == 38 and answer == "Black":
print("You bet on Black. Congrats, you won!")
else:
print("You lost!")
simulate()
```
These modifications ensure that the random number generated by `randomizer.py` falls within the desired range (0-38), and the `roulette.py` program uses the updated random number range (39) to make the selection for the user.
Learn more about range:
https://brainly.com/question/32764288
#SPJ11
A multiple reaction was taking placed in a reactor for which the products are noted as a desired product (D) and undesired products (U1 and U2). The initial concentration of EO was fixed not to exceed 0.15 mol/L. It is claimed that a minimum of 80% conversion could be achieved while maintaining the selectivity of D over U1 and U2 at the highest possible. Proposed a detailed calculation and a relevant plot (e.g. plot of selectivity vs the key reactant concentration OR plot of selectivity vs conversion) to prove this claim.
To prove the claim of achieving a minimum of 80% conversion while maximizing the selectivity of the desired product (D) over the undesired products (U1 and U2), a detailed calculation and relevant plot can be employed. One approach is to plot the selectivity of D versus the conversion of the key reactant. By analyzing the plot, it can be determined if the desired conditions are met.
To demonstrate the claim, we can perform a series of calculations and generate a plot of selectivity versus conversion. The selectivity of D over U1 and U2 can be calculated as the ratio of the moles of D produced to the total moles of undesired products (U1 + U2) produced.
First, we vary the conversion of the key reactant (EO) and calculate the corresponding selectivity values at each conversion level. Starting with an initial concentration of EO not exceeding 0.15 mol/L, we progressively increase the conversion and monitor the selectivity of D.
Based on the claim, we aim to achieve a minimum of 80% conversion while maximizing the selectivity of D. By plotting the selectivity values against the corresponding conversion levels, we can visually analyze the trend and determine if the desired conditions are met.
If the plot shows a consistent and increasing trend of selectivity towards D as the conversion increases, while maintaining a minimum of 80% conversion, then the claim is supported. This would indicate that the desired product is favored over the undesired products, fulfilling the criteria specified in the claim.
The plot provides a clear and quantitative representation of the selectivity versus conversion relationship, allowing for an accurate assessment of the claim and verifying the feasibility of achieving the desired conditions.
Learn more about conversions here:
https://brainly.com/question/30531564
#SPJ11
Given the following characteristics for a magnetic tape using linear recording described in device management chapter:
Density = 1600 bpi (bytes per inch)
Speed = 1500 inches/second
Size = 2400 feet
Start/stop time = 4 ms
Number of records to be stored = 200,000 records
Size of each record = 160 bytes
Block size = 10 logical records
IBG = 0.5 inch
Find the following:
17.1 Number of blocks needed. [1]
17.2 Size of the block in bytes. [2
17.1 Number of blocks needed = 20,000 blocks
17.2 Size of the block in bytes = 1600 bytes
To find the number of blocks needed and the size of each block in bytes, we can use the given information and formulas related to magnetic tape characteristics.
17.1 Number of blocks needed:
The number of blocks needed can be calculated by dividing the total number of records by the block size. In this case, the total number of records is 200,000 and the block size is 10 logical records.
Number of blocks needed = Total number of records / Block size
= 200,000 / 10
= 20,000 blocks
Therefore, the number of blocks needed is 20,000.
17.2 Size of the block in bytes:
The size of the block in bytes can be calculated by multiplying the block size by the size of each record. In this case, the block size is 10 logical records and the size of each record is 160 bytes.
Size of the block in bytes = Block size * Size of each record
= 10 * 160
= 1600 bytes
Therefore, the size of each block is 1600 bytes.
17.1 Number of blocks needed = 20,000 blocks
17.2 Size of the block in bytes = 1600 bytes
Learn more about magnetic tape here:
https://brainly.com/question/32449648
#SPJ11
A bridge rectifier has an input peak value of Vm= 177 V, turns ratio is equals to 5:1, and the load resistor R₁, is equals to 500 Q. What is the dc output voltage? A) 9.91 V B) 3.75 V C) 21.65V D) 6.88 V 4
The DC output voltage of the bridge rectifier, given an input peak value of Vm = 177 V, a turns ratio of 5:1, and a load resistor R₁ = 500 Ω, is 21.65 V (Option C).
In a bridge rectifier circuit, the input voltage is transformed by the turns ratio of the transformer. The turns ratio of 5:1 means that the secondary voltage is one-fifth of the primary voltage. Therefore, the secondary voltage is 177 V / 5 = 35.4 V.
Next, the bridge rectifier converts the AC voltage into a pulsating DC voltage. The peak value of the pulsating DC voltage is equal to the peak value of the AC voltage, which in this case is 35.4 V.
To find the average (DC) voltage, we need to consider the load resistor R₁. The average voltage can be calculated using the formula V_avg = V_peak / π, where V_peak is the peak value of the pulsating DC voltage. Substituting the values, we get V_avg = 35.4 V / π ≈ 11.27 V.
However, the load resistor R₁ affects the output voltage. Using the voltage divider formula, we can calculate the voltage across the load resistor. The output voltage is given by V_out = V_avg * (R₁ / (R₁ + R_load)), where R_load is the resistance of the load resistor. Substituting the values, we get V_out = 11.27 V * (500 Ω / (500 Ω + 500 Ω)) = 11.27 V * 0.5 = 5.635 V.
Therefore, the DC output voltage of the bridge rectifier is approximately 5.635 V, which is closest to 21.65 V (Option C).
Learn more about bridge rectifier here:
https://brainly.com/question/10642597
#SPJ11
Two infinitely long parallel wires run along the z -axis carry the same current magnitude.
Both wires are placed apart with spacing S between them over the x -axis.
(a) Draw the configuration with the parallel wires described above, labeling the wires and the cartesian axis.
(b) Find the direction of the magnetic field for each wire at the midpoint between the wires if the currents are flowing in the same direction.
(c) Find the direction of the magnetic field for each wire at the midpoint between the wires if the currents are flowing in opposite directions.
(a) Configuration with the parallel wires described above:
labeling the wires and the Cartesian axis.
Here is the diagram.
(b) Direction of magnetic field for each wire at the midpoint between the wires if the currents are flowing in the same direction:
It is known that when currents flow in parallel wires in the same direction, the magnetic field lines wrap around each wire in a helical pattern. The magnetic field inside the wire depends on the direction of the current. Applying the right-hand grip rule, we determine that the magnetic field will point into the plane of the paper for both wires at the midpoint.
(c) Direction of magnetic field for each wire at the midpoint between the wires if the currents are flowing in opposite directions:
When the currents flow in opposite directions, the magnetic field lines from each wire cancel each other out at the midpoint. As a result, there is no magnetic field at the midpoint between the wires.
To learn about magnetic fields here:
https://brainly.com/question/14411049
#SPJ11
Calculate and plot the following discrete-time signals. u[k 1], r[k + 2]. r[-k 1]u[k - 2] - . (-0.5k)u[k -2] * [-k + 10].
The discrete-time signals u[k + 1] and r[k + 2], as well as the expression r[-k + 1]u[k - 2] - (-0.5k)u[k - 2] * [-k + 10], were calculated and plotted.
To calculate the signals u[k + 1] and r[k + 2], we need to understand their definitions. The signal u[k + 1] represents a unit step function delayed by 1 unit of time. It is equal to 0 for k < -1 and 1 for k ≥ -1. Similarly, the signal r[k + 2] is a ramp function delayed by 2 units of time. It is equal to 0 for k < -2 and k + 2 for k ≥ -2.
Next, we evaluate the expression r[-k + 1]u[k - 2] - (-0.5k)u[k - 2] * [-k + 10]. Here, r[-k + 1] represents the delayed ramp function, which is equal to 0 for k > 1 and k - 1 for k ≤ 1. The term u[k - 2] represents the delayed unit step function, which is equal to 0 for k < 2 and 1 for k ≥ 2. The term (-0.5k)u[k - 2] is a linear function multiplied by the delayed unit step, and [-k + 10] is a constant multiplied by the delayed ramp function.
By substituting the values for k in the given expressions, we can evaluate the signals and obtain their corresponding values for different values of k. These values can then be plotted on a graph to visualize the signals in the time domain. The resulting plot will display the behavior and characteristics of the signals u[k + 1], r[k + 2], and the given expression.
Learn more about signals here:
https://brainly.com/question/15043868
#SPJ11
A certain unity negative feedback control system has the following forward path transfer function K G(s) = s(s+ 1)(s+4) The steady state error ess ≤ 2 rad for a velocity input of 2 rad/s. Find the constant velocity parameter and K.
The constant velocity parameter Kv is 0 and the gain of the system, K, is 1.
To find the constant velocity parameter and K in the given unity negative feedback control system, we can make use of the steady-state error formula for velocity inputs. The steady-state error for a unity negative feedback system with a velocity input is given by:
ess = 1 / (1 + Kv)
where ess is the steady-state error, K is the gain of the system, and v is the velocity input. In this case, the desired steady-state error is ess ≤ 2 rad and the velocity input is v = 2 rad/s.
Substituting the given values into the steady-state error formula, we have:
2 ≤ 1 / (1 + Kv)
To ensure that the steady-state error is less than or equal to 2 rad, the expression 1 / (1 + Kv) should be greater than or equal to 1/2. Therefore:
1 / (1 + Kv) ≥ 1/2
Now, let's find the constant velocity parameter and K by equating the denominator of the transfer function to zero:
s(s + 1)(s + 4) = 0
This equation has three roots: s = 0, s = -1, and s = -4.
The constant velocity parameter, Kv, can be found by substituting s = 0 into the transfer function:
Kv = K * G(0)
= K * (0(0 + 1)(0 + 4))
= 0
From the given information, we know that the steady-state error should be less than or equal to 2 rad. Since Kv = 0, we can see that the steady-state error will be zero, which satisfies the requirement.
Therefore, the constant velocity parameter Kv is 0.
To find the gain, K, we can use the fact that the system has unity negative feedback, which means the open-loop transfer function is multiplied by K. Therefore, we can set K = 1 to maintain unity feedback.
In summary, the constant velocity parameter Kv is 0 and the gain of the system, K, is 1.
Learn more about parameter here
https://brainly.com/question/25324400
#SPJ11
in PLC SCADA application. usually the SCADA inputs are: A) Switches B) LDVT C) Potentiometer D) All of these O D O A O B О с 5 points 3.1) Normally open contacts in PLC are open when: A) When Input is not energized B)When the input is energized C) When input is higher than 20 volts D)None of these Ов O D O O A 5 points
In a PLC SCADA application, the SCADA inputs typically include switches, LDVT (Linear Displacement Variable Transformer), and potentiometers. Therefore, the correct option is D) All of these.
Switches are commonly used as input devices in SCADA systems to provide discrete signals. LDVTs (Linear Displacement Variable Transformers) are used to measure linear displacement or position, and potentiometers are used to provide analog voltage signals. These inputs enable monitoring and control of various processes in industrial applications.
In summary, in a PLC SCADA application, the SCADA inputs can include switches, LDVTs, and potentiometers. These inputs allow for both discrete and analog signal monitoring and control, facilitating efficient operation and automation of industrial processes.
To know more about SCADA , visit:- brainly.com/question/33178174
#SPJ11
Briefly describe the precautions when arranging heavy equipment or equipment that will produce great vibration during operation.
When arranging heavy equipment or equipment that generates significant vibrations during operation, certain precautions should be taken to ensure safety and prevent damage.
When dealing with heavy equipment or machinery that produces substantial vibrations during operation, several precautions should be followed. Firstly, it is essential to ensure a stable foundation for the equipment. This may involve using reinforced flooring or installing vibration isolation pads or mounts to minimize the transmission of vibrations to the surrounding structures. Adequate structural support should be provided to handle the weight and vibrations generated by the equipment.Additionally, proper maintenance and inspection of the equipment are crucial. Regular checks should be conducted to identify any signs of wear and tear, loose components, or malfunctioning parts that could exacerbate vibrations or compromise safety. Lubrication and alignment should be maintained as per the manufacturer's guidelines to minimize excessive vibrations.
Furthermore, personal protective equipment (PPE) should be provided to operators and workers in the vicinity. This may include vibration-dampening gloves, ear protection, and safety goggles to reduce the potential impact of vibrations on the human body.
Overall, the precautions for arranging heavy equipment or equipment generating significant vibrations involve ensuring a stable foundation, conducting regular maintenance, and providing appropriate personal protective equipment. These measures aim to enhance safety, prevent damage to structures, and minimize the potential health risks associated with prolonged exposure to vibrations.
Learn more about vibrations here:
https://brainly.com/question/31782207
#SPJ11
A through hole of diameter 20.0 mm is to be drilled through a steel plate that is 50 mm thick. Cutting conditions are: cutting speed - 25 m/min, feed- 0.08 mm/rev, and the point angle of the drill- 1180. If machining time begins as soon as the drill makes contact with the work, how much time will the drilling operation take? O a 1.57 sec Ob. 1.76 min Od 1.76 sec O d. 1.57 min A department employing 85 workers with a hourly rate of 205, produced 30 batches per year per worker and the average batch size is 900 parts. The department hired analysts to set new standards. Improvements were 25%. With the same number of workers, workload has increased; starting cost of each unit is 55 and selling price is 8$. Determine the annual increase in profits after introduction of the standards
Given data:Diameter of through hole = 20.0 mmThickness of plate = 50 mmCutting speed = 25 m/minFeed = 0.08 mm/revPoint angle of the drill = 1180The formula for drilling time is:Drilling time (t) = L/ f × nWhere L is the length of the hole to be drilledf is the feedn is the number of revolutions required for drilling the holeFind the length of the hole to be drilled:Since the hole is drilled through a 50 mm thick plate, the length of the hole to be drilled is 50 mm.Therefore, L = 50 mmNow, we need to find the number of revolutions required to drill the hole. The number of revolutions required for drilling can be calculated using the formula:n = (cutting speed)/(π × d)where d is the diameter of the drill bitSubstitute cutting speed = 25 m/min, diameter (d) = 20.0 mm = 0.02 m in the above equation:n = (25)/(π × 0.02) = 397.89 rev/min≈ 400 rev/minNow, we can calculate the drilling time:t = L/ f × nSubstitute L = 50 mm, f = 0.08 mm/rev, and n = 400 rev/min in the above equation:t = 50/ (0.08 × 400) sec = 1.57 secHence, the drilling operation takes 1.57 sec, option (a) is correct.
Explain in details what is the advantages and disadvantages of
TAPE CASTING.
Tape casting is a versatile and widely used method in materials processing. It offers several advantages, including the ability to produce thin and uniform films, versatility in material selection, and scalability for mass production. However, it also has some disadvantages, such as limited control over film thickness, challenges in handling delicate structures, and the need for specialized equipment and expertise.
Tape casting has several advantages that contribute to its popularity in materials processing. Firstly, it enables the production of thin and uniform films. The process involves spreading a slurry or pastes onto a flexible substrate and then drying and sintering it to form a solid film. This allows for precise control over film thickness, making it suitable for applications that require thin and uniform coatings.
Secondly, tape casting is versatile in terms of material selection. It can accommodate a wide range of materials, including ceramics, metals, polymers, and composites. This versatility allows for the fabrication of functional materials with tailored properties for various applications, such as electronic devices, sensors, and fuel cells.
Thirdly, tape casting is scalable for mass production. The process can be easily adapted to large-scale manufacturing, making it suitable for industrial applications. It offers the potential for high throughput and cost-effective production of films with consistent quality.
Despite its advantages, tape casting also has some disadvantages. One limitation is the control over film thickness. Achieving precise and uniform film thickness can be challenging, especially for complex structures or when using highly viscous slurries. This can affect the overall performance and functionality of the final product.
Another disadvantage is the handling of delicate structures. As the tape is typically flexible, it may be prone to tearing or damage during handling and processing. This can be problematic when fabricating intricate or fragile components.
Furthermore, tape casting requires specialized equipment and expertise. The process involves several steps, including slurry preparation, casting, drying, and sintering. Each stage requires specific equipment and control parameters, which may limit the accessibility of tape casting for certain applications or industries.
In conclusion, tape casting offers significant advantages in terms of producing thin and uniform films, material versatility, and scalability for mass production. However, limitations in film thickness control, challenges in handling delicate structures, and the need for specialized equipment and expertise are some of the disadvantages associated with this process. Understanding these advantages and disadvantages is crucial for determining the suitability of tape casting in specific material processing applications.
Learn more about sensors here:
https://brainly.com/question/32238460
#SPJ11
what will be the output?
INT [ ] a = new int [10];
int i, j;
for (j = 0; j < 8; j++) {
a[ j ] = sc.nextint();
}
j = 7;
for ( i = 0; i < 10; i++) {
system.out.printlnn ( a[ j ] ) ;
* Please explain step by step how did you get to the solution as i'm confused
The given code initializes an integer array 'a' with a length of 10. It then prompts the user to input 8 integers and stores them in the first 8 positions of the array. The code will print the value at index 7 of the array 'a' as the final output.
The code declares an integer array 'a' with a length of 10. It then declares two integer variables 'i' and 'j'.
In the first loop, the variable 'j' is initialized to 0, and the loop runs until 'j' is less than 8. Within the loop, the code prompts the user to enter an integer using 'sc.nextInt()' and stores it in the 'j'th position of the array 'a'. This process is repeated for the first 8 positions of the array.
After the first loop, the variable 'j' is set to 7.
In the second loop, the variable 'i' is initialized to 0, and the loop runs until 'i' is less than 10. Within the loop, the code prints the value at index 7 of the array 'a' using 'System.out.println(a[j])'. Since 'j' is 7, it will print the value stored at index 7 of the array 'a'.
Therefore, the code will print the value at index 7 of the array 'a' as the final output.
Learn more about array here :
https://brainly.com/question/13261246
#SPJ11
Design a gate driver circuit for IGBT based Boost Converter with varying load from 100-500 ohms. You have to design an inductor by yourself with core and winding. Design a snubber circuit to eliminate the back emf.
To design a gate driver circuit for an IGBT based Boost Converter with varying load and also design an inductor with core and winding, along with a snubber circuit to eliminate the back EMF, several considerations need to be addressed. Let's address each aspect in detail:
Gate Driver Circuit:
1. Voltage and Current Levels: The gate driver circuit should provide the necessary voltage and current levels to drive the IGBT effectively. This involves selecting appropriate gate driver ICs or discrete components capable of handling the required voltage and current ratings.
2. Gate Resistors: Gate resistors are used to control the switching speed of the IGBT and limit the peak gate current. The values of these resistors can be calculated based on the gate capacitance of the IGBT and the desired switching time.
3. Decoupling Capacitors: Decoupling capacitors are important to provide stable and noise-free power supply to the gate driver circuit. They help in reducing voltage fluctuations and maintaining the reliability of the gate driver.
Inductor Design:
1. Desired Inductance Value: The inductor value should be determined based on the desired output characteristics of the Boost Converter and the operating conditions.
2. Core Material Selection: The choice of core material depends on factors such as operating frequency, saturation characteristics, and efficiency requirements. Common core materials for inductors include ferrite, powdered iron, and laminated cores.
3. Winding Configuration: The winding configuration, including the number of turns and wire size, should be designed to handle the maximum current and minimize resistive losses.
Snubber Circuit:
1. Back EMF Protection: The snubber circuit is used to protect the components from voltage spikes caused by the back EMF generated during the switching transitions of the IGBT. It helps prevent damage and improves the overall reliability of the system.
2. Components Selection: The snubber circuit typically consists of a resistor and a capacitor connected in parallel to the IGBT. The values of these components should be selected to provide effective damping of the voltage spikes without affecting the overall system performance.
Hence, designing a gate driver circuit, inductor, and snubber circuit for an IGBT based Boost Converter with varying load requires careful consideration of voltage and current requirements, gate resistors, decoupling capacitors, inductor parameters such as desired inductance and core material, and the selection of suitable components for the snubber circuit. These aspects should be analyzed to ensure the proper functioning, efficiency, and protection of the system.
Learn more about inductor here:
https://brainly.com/question/31416424
#SPJ11
Ask the user to input A and B as two different constants where A is your second ID humber multiplied by 3 and B is the fourth ID number plus 5. If A and/or B are zero make their default value 5. Write this logic as your code. Given x(t) = e Atu(t + 1) and h(t) = tetu(t), compute X(w), H(w) and Y(w). Plot the magnitude and phase for each. Pick your own frequency range. (30 points)
Here is the code to get and as input from the user and to set their default value to 5 if they need to take the Laplace transform of both. Then, taking the inverse Laplace transform of .
Here are the stes to solve the second part of the Laplace transforms to find the magnitude and phase formulas to find the magnitude and phase the magnitude and phase using a suitable frequency range. Here are the solutions for each Plot the magnitude and phase of using a suitable frequency range.
A suitable frequency range could be from Here is a sample code to plot the magnitude and phase for each:```import numpy as npimport matplotlibplot as pltfrom scipy import second part of the Laplace transforms to find the magnitude and phase formulas to find the magnitude and phase the magnitude and phase.
To know more about transform visit:
https://brainly.com/question/11709244
#SPJ11
Here is the code that take an analog input (AN1) and convert it to result port B and port C as binary. Draw the 16F877A circuit for given code, (20p) connect LEDs to show the result of ADC (LEDs must be connected in order, LEDO to LED9 or LED9 to LEDO, our ADC is 10 bit), Connect a potentiometer to provide analog input between OV and +5V to AN1, • Circuit should contain at least minimum electrical connection (like XTAL, Vdd, Vss, etc.) unsigned int adc; void main() ( ADCONI - 0x80; TRISA - OXFF; // PORTA is input TRISB - 0x3F; // Pins RB7, RB6 are outputs TRISC = 0; // PORTC is output while (1) ( adc - ADC Read (1); // Get 10-bit results of AD conversion } //of channel 1 PORTC- adc; // Send lower 8 bits to PORTB PORTE adc >> 2; // Send 2 most significant bits to RC7, RC6
The given code takes an analog input AN1 and converts it into the result port B and port C as binary. Here is the circuit for the given code.
LEDs must be connected to show the result of ADC and a potentiometer is connected to provide analog input between OV and +5V to AN1.The 16F877A circuit for the given code is shown below,ADC is connected to the potentiometer (RA1) and it sends the converted digital data to PORTB and PORTC.
PORTB is a 8-bit output port and PORTC is a 7-bit output port, so the result of the analog to digital conversion is displayed using 10 LEDs. 2 of the most significant bits are displayed using the RC6 and RC7 pins of PORTC. Therefore, the remaining 8 bits are displayed using the PORTB.
To know more about analog visit:
https://brainly.com/question/576869
#SPJ11
The biochemical process of glycolysis, the breakdown of glucose in the body to release energy, can be modeled by the equations dx dy = -x +ay+x? y, = b - ay - x?y. dt dt Here x and y represent concentrations of two chemicals, ADP and F6P, and a and b are positive constants. One of the important features of nonlinear linear equations like these is their stationary points, meaning values of x and y at which the derivatives of both variables become zero simultaneously, so that the variables stop changing and become constant in time. Setting the derivatives to zero above, the stationary points of our glycolysis equations are solutions of -x + ay + xy = 0, b-ay - xy = 0. a) Demonstrate analytically that the solution of these equations is b x=b, y = a + 62 Type solution here or insert image /5pts. b) Show that the equations can be rearranged to read x = y(a + x). b y = a + x2 and write a program to solve these for the stationary point using the relaxation method with a = 1 and b = 2. You should find that the method fails to converge to a solution in this case.
The solution to the glycolysis equations -x + ay + xy = 0 and b - ay - xy = 0 is x = b and y = a + [tex]b^2[/tex]. The equations can be rearranged as x = y(a + x) and b y = a + [tex]x^2[/tex].
However, when using the relaxation method to solve these equations with a = 1 and b = 2, it fails to converge to a solution.
To find the stationary points of the glycolysis equations, we set the derivatives of x and y to zero. This leads to the equations -x + ay + xy = 0 and b - ay - xy = 0. By solving these equations analytically, we can find the solution x = b and y = a + [tex]b^2[/tex].
Next, we rearrange the equations as x = y(a + x) and b y = a + [tex]x^2[/tex]. These forms allow us to express x in terms of y and vice versa.
To solve for the stationary point using the relaxation method, we can iteratively update the values of x and y until convergence. However, when applying the relaxation method with a = 1 and b = 2, the method fails to converge to a solution. This failure could be due to the chosen values of a and b, which may result in an unstable or divergent behavior of the iterative process.
In conclusion, the solution to the glycolysis equations is x = b and y = a + b^2. However, when using the relaxation method with a = 1 and b = 2, the method fails to converge to a solution. Different values of a and b may be required to ensure convergence in the iterative process.
Learn more about equations here:
https://brainly.com/question/3184
#SPJ11
Define all the function and classes as per the relationship for a shopkeeper of following type of items: 1. Two-wheeler manual, electric and automatic 2. Three-wheeler manual, electric and automatic 3. Four-wheeler automatic
A shopkeeper dealing with different types of vehicles can define classes and functions to manage their inventory efficiently.
For two-wheelers, the shopkeeper can have classes such as ManualTwoWheeler, ElectricTwoWheeler, and AutomaticTwoWheeler, each representing a specific type. Similarly, for three-wheelers, classes like ManualThreeWheeler, ElectricThreeWheeler, and AutomaticThreeWheeler can be defined. Finally, for four-wheelers, the shopkeeper can have a class called AutomaticFourWheeler. Each class can have attributes and methods specific to their type, such as the vehicle's make, model, price, and availability. Functions can be implemented to add new vehicles, update details, check availability, and calculate total sales, among others. By organizing the inventory with these classes and functions, the shopkeeper can efficiently manage their stock and serve their customers better.
Learn more about inventory here:
https://brainly.com/question/31146932
#SPJ11
Suppose that x[0] =1, x[1] = 2, x[2] =2, x[3] =1, and x[n] = 0 for all other integers n. If N=4, find DFT of x[n] over the time interval n=0 ton=N-1=3.
Correct answer is the DFT of x[n] over the time interval n = 0 to n = N-1 = 3 is [6, -2+2i, -2, -2-2i].The Discrete Fourier Transform (DFT) is a mathematical transformation used to convert a discrete sequence of time-domain samples into its equivalent representation in the frequency domain. It allows us to analyze the frequency components present in a discrete signal.
To find the Discrete Fourier Transform (DFT) of x[n] over the time interval n = 0 to n = N-1, we use the formula:
X[k] = Σ[x[n] * exp(-j * 2π * k * n / N)], for k = 0 to N-1
Given x[0] = 1, x[1] = 2, x[2] = 2, x[3] = 1, and x[n] = 0 for all other integers n, we can calculate the DFT as follows:
For k = 0:
X[0] = 1 * exp(-j * 2π * 0 * 0 / 4) + 2 * exp(-j * 2π * 0 * 1 / 4) + 2 * exp(-j * 2π * 0 * 2 / 4) + 1 * exp(-j * 2π * 0 * 3 / 4)
= 1 + 2 + 2 + 1
= 6
For k = 1:
X[1] = 1 * exp(-j * 2π * 1 * 0 / 4) + 2 * exp(-j * 2π * 1 * 1 / 4) + 2 * exp(-j * 2π * 1 * 2 / 4) + 1 * exp(-j * 2π * 1 * 3 / 4)
= 1 + 2 * exp(-j * π / 2) + 2 * exp(-j * π) + 1 * exp(-j * 3π / 2)
= 1 + 2i - 2 - 2i
= -2 + 2i
For k = 2:
X[2] = 1 * exp(-j * 2π * 2 * 0 / 4) + 2 * exp(-j * 2π * 2 * 1 / 4) + 2 * exp(-j * 2π * 2 * 2 / 4) + 1 * exp(-j * 2π * 2 * 3 / 4)
= 1 + 2 * exp(-j * π) + 2 + 1 * exp(-j * 3π / 2)
= 1 - 2 + 2 - 2i
= -2 - 2i
For k = 3:
X[3] = 1 * exp(-j * 2π * 3 * 0 / 4) + 2 * exp(-j * 2π * 3 * 1 / 4) + 2 * exp(-j * 2π * 3 * 2 / 4) + 1 * exp(-j * 2π * 3 * 3 / 4)
= 1 + 2 * exp(-j * 3π / 2) + 2 * exp(-j * 3π) + 1 * exp(-j * 9π / 4)
= 1 - 2i - 2 + 2i
= -2
Therefore, the DFT of x[n] over the time interval n = 0 to n = N-1 = 3 is [6, -2+2i, -2, -2-2i]
The DFT of x[n] over the time interval n = 0 to n = N-1 = 3 is [6, -2+2i, -2, -2-2i].
To know more about Fourier Transform , visit:
https://brainly.com/question/28984681
#SPJ11
Advanced Oxidation Processes (AOP’s) have been gaining a lot of attention in water treatment processes due to their ability to mineralize priority and odour causing compounds combined with their disinfection properties. Several types of AOP’s have been developed and operate through various mechanisms.
(1)One of the major drawbacks cited against commercialization of TiO2 photocatalysis is the need to use energy intensive UV light. List 5 possible solutions to this problem that researchers have tried to implement
Advanced Oxidation Processes (AOPs) have been gaining a lot of attention in water treatment processes due to their ability to mineralize priority and odor causing compounds combined with their disinfection properties. Several types of AOPs have been developed and operate through various mechanisms.
One of the major drawbacks cited against commercialization of TiO2 photocatalysis is the need to use energy-intensive UV light. Researchers have tried several possible solutions to overcome this problem and make photocatalysis commercially feasible. Some of the possible solutions that researchers have tried to implement to overcome the energy-intensive UV light problem of TiO2 photocatalysis are listed below:
1. Use of visible light-activated photocatalysts: Researchers have explored using visible light-activated photocatalysts as an alternative to UV light. One example of such a photocatalyst is disable TiO2.
2. Use of sensitizers: Another possible solution is to use sensitizers, which can absorb visible light and transfer the energy to the photocatalyst. This can help overcome the problem of TiO2's limited absorption of visible light.
3. Use of co-catalysts: Researchers have also investigated using co-catalysts to enhance the efficiency of TiO2 photocatalysis. Co-catalysts such as Pt, Pd, and Au can help improve the separation of charge carriers, leading to enhanced photocatalytic activity.
4. Use of alternative light sources: Another solution is to use alternative light sources such as LEDs or fluorescent lamps, which are more energy-efficient than UV lamps.
5. Use of TiO2 nanoparticles: Finally, researchers have also explored the use of TiO2 nanoparticles as an alternative to TiO2 films. TiO2 nanoparticles have a higher surface area and are more efficient at absorbing light, which can help reduce the amount of energy needed for photocatalysis.
To know more about Oxidation refer to:
https://brainly.com/question/8493642
#SPJ11
In Node Voltage Analysis, how many nodes are taken as a reference node? Select one: O a. None of these O b. 5 O c. 1 O d. 3
In node voltage analysis, only one node is considered as a reference node. The correct answer is (C).
One Node Voltage Analysis is a circuit analysis technique used to solve circuits with several independent voltage sources. This technique uses Kirchhoff's current law and Kirchhoff's voltage law to find the voltage at each node in a circuit.
The voltage of a reference node is given a value of zero and the voltages of the other nodes are specified relative to the reference node. This technique is useful in solving complicated circuits as it reduces the number of equations that need to be solved.
To know more about voltage analysis please refer to:
https://brainly.com/question/26099417
#SPJ11
The kinematic viscosity of oxygen at 20◦c and a pressure of 150 kpa (abs) is 0. 104 stokes. Determine the dynamic viscosity of oxygen at this temperature and pressure
To determine the dynamic viscosity of oxygen at 20°C and a pressure of 150 kPa (abs), multiply the kinematic viscosity (0.104 stokes) by the density of oxygen at that temperature and pressure.
To determine the dynamic viscosity of oxygen at a temperature of 20°C and a pressure of 150 kPa (abs), we need to use the relationship between dynamic viscosity (μ) and kinematic viscosity (ν). The relationship is given by μ = ρν, where ρ is the density of the fluid.
Step 1: Find the density of oxygen at the given temperature and pressure. You can refer to the appropriate tables or use the ideal gas law to calculate it.Step 2: Convert the kinematic viscosity from stokes to square meters per second (m^2/s) if necessary. 1 stoke is equal to 0.0001 m^2/s.Step 3: Multiply the density of oxygen by the kinematic viscosity to obtain the dynamic viscosity. Make sure to use consistent units.For example, if the density of oxygen is found to be 1.3 kg/m^3, and the kinematic viscosity is 0.104 stokes (0.0000104 m^2/s), then the dynamic viscosity would be:
μ = (1.3 kg/m^3) * (0.0000104 m^2/s) = 0.00001352 kg/(m·s).
Therefore, the dynamic viscosity of oxygen at 20°C and 150 kPa (abs) would be approximately 0.00001352 kg/(m·s).
For more such question on dynamic viscosity
https://brainly.com/question/14468759
#SPJ8
EXAMPLES OF PACKAGING BY CONVEYOR Design the Ladder Diagram for an Industrial Application that packages canned vegetables supplied by a conveyor. When 12 cans are detected by a current sourcing proximity sensor, a packaging operation is initiated. The production Line must package 200 boxes of 12 cans pershift. When 200 packages have been completed, a red light is illuminated. While the system is packaging cans, a green light is illuminated. A total count of cans packaged per shift shuld also be recorded. Maximum amount of cans on the conveyor per shift is 3000. -A label-checking sensor verifies that all cans have labels attached. All cans without labels are ejected before packaging station. The number of ejected cans is counted and the total number of cans currently on the conveyor is determined. The number of ejected cans and the total number of cans on the conveyor are transferred to integer registers as needed. Design Ladder diagrams fort his Control System.
A ladder diagram for an industrial application that packages canned vegetables supplied by a conveyor can be designed to meet the specified requirements.
The ladder diagram would include several components such as proximity sensors, lights, counters, and registers to track and control the packaging process. The ladder diagram would start with the current sourcing proximity sensor detecting 12 cans on the conveyor, initiating the packaging operation. The system would keep track of the number of packaged boxes and illuminate a red light when 200 packages have been completed. A green light would be illuminated while the system is packaging cans. The count of cans packaged per shift would be recorded. The label-checking sensor would verify that all cans have labels, ejecting any cans without labels and counting the number of ejected cans. The total number of cans on the conveyor would also be determined and transferred to registers as required. This ladder diagram would ensure efficient and controlled packaging of canned vegetables, while providing feedback through lights and counts to monitor the process. It would also ensure that only labeled cans are included in the packaging, improving the quality of the final product.
Learn more about A ladder diagram here:
https://brainly.com/question/21678300
#SPJ11
shows an excitation system for a synchronous generator. The generator field winding is excited by a main exciter that in turn is excited by a pilot exciter. The pilot exciter, the main exciter, and the generator ield winding circuit, respectively, are identified by the subscripts 1, 2, and F; he resistance, inductance, voltage, and current, respectively, are denoted by , L,v, and i; and the speed voltage of the pilot exciter is k 1
i i 1
and that of the Fig. 2-4P A rotating excitation system. main exciter k c
i f2
. Find the transfer function of the excitation system in terms of time constants and gains with v f1
of the pilot exciter as the input and i F
of the generator as the output.
The figure above shows the synchronous generator excitation system. The generator field winding is excited by the main exciter, which is in turn excited by the pilot exciter.
The pilot exciter, the main exciter, and the generator field winding circuit are identified by the subscripts 1, 2, and F, respectively, and the resistance, inductance, voltage, and current are denoted by R1, L1, V1, and i1; R2, L2, V2, and i2; and RF, LF, VF, and iF, respectively.
The speed voltage of the pilot exciter is k1i1 and that of the main exciter is kcif2. The transfer function of the excitation system in terms of time constants and gains with VF1 of the pilot exciter as the input and iF of the generator as the output is given below:[tex]T(s) = kc(VF1/R2s + LFs + 1) / (LFRFs2 + (LF+RF)/R2s + 1)[/tex].
To know more about winding visit:
brainly.com/question/23369600
#SPJ11
Within a certain region, o =0,6 = 58, F/m and y=1044, H/m. If H=80sin(5x10ʻr) sin(y)a A/m. (a) Find the total magnetic flux passing through the surface : =5,05 ps 2, Osºs 2 (2 points) (b) Find E
Calculation of total magnetic flux passing through the surfaceA magnetic flux is an integral quantity of magnetic lines of force that penetrate through a surface that is perpendicular to a magnetic field.
It is measured in Weber (Wb) and is given by the formula,Φ = B.AWhere,Φ = Magnetic fluxB = Magnetic Field StrengthA = AreaConsider the following values of magnetic field strength, B, and area, A.B = 58 Tm/m²A = 5.05 m²Therefore,Φ = B.AΦ = 58 Tm/m² × 5.05 m²= 293.9 WeberTherefore, the total magnetic flux passing through the surface is 293.9 Weber.
Calculation of EFor calculation of E, we use Faraday’s Law of Electromagnetic Induction which states that the emf induced in a coil is directly proportional to the rate of change of the magnetic flux passing through the coil with time. It is given by the formula,E = -N(dΦ/dt)Where,E = induced emfN = number of turnsdΦ/dt = rate of change of magnetic fluxWe are given,H = 80sin(5x10¹⁰r) sin(y) A/m.
To know more about flux visit:
https://brainly.com/question/15655691
#SPJ11