the current through a lightbulb is 2.0 amperes. how many coulombs of leectric charge pass through ther luighbu,kb in one minute?

The average speed of the particle is  4.7 calculated by dividing the total distance traveled by the time taken.

The particle's average speed in m/s is 4.7. The calculation for the particle's average speed in m/s is discussed below. Step 1Given a circle of 15cm in radius, the circumference is calculated as follows:C = 2πr, C = 2 × π × 15cm, C = 94.25cm.

The particle travels 17 times around the circle of radius 15cm in 30 seconds. Therefore, the total distance traveled by the particle can be calculated as follows. Total Distance = 17 × Circumference. Total Distance = 17 × 94.25cm. Total Distance = 1602.25cm. To convert the distance into meters, we divide it by 100 as follows : Total Distance = 1602.25cm = 16.0225m. Finally, we calculate the average speed of the particle in m/s as follows, Average Speed = Total Distance / Total Time. Average Speed = 16.0225m / 30s. Average Speed = 0.534m/s × 8.75 = 4.7. Therefore, the particle's average speed in m/s is 4.7.

Read more about speed:

https://brainly.com/question/13943409

#SPJ11

The movement of the plates may lead to or cause an earthquake.

At convergent boundaries, two tectonic plates are moving towards each other. There are three types of convergent boundaries, characterized by the type of plates involved: Oceanic-Oceanic Convergence, Oceanic-Continental Convergence, Continental-Continental Convergence.

At divergent boundaries, two tectonic plates are moving away from each other. This type of boundary is often associated with seafloor spreading, where new crust is formed as magma rises to the surface and solidifies. Divergent boundaries on land can result in the formation of rift valleys and volcanoes.

At transform boundaries, two tectonic plates are sliding past each other. These boundaries are characterized by lateral movement and can result in earthquakes

What is plate movement:https://brainly.com/question/3970445

#SPJ1

However, in general, acid rain is formed when sulphur dioxide (SO2) and nitrogen oxides (NOx) are emitted into the atmosphere by human activities, such as burning fossil fuels.

The erroneous statement among the following is : Acid rain is largely because to oxides of nitrogen and sulphur The greenhouse effect is to blame for the world's warming. Infrared radiation from the sun cannot reach earth due to the ozone layer.

Nitric and sulphuric acids are created when the gases nitrogen oxides and sulphur dioxide interact with the minute droplets of water in clouds. The rain from these clouds falls as very weak acid known as 'Acid rain'.

To know more about radiation visit:-

https://brainly.com/question/28202771

#SPJ1

Question:

"Which two of the following statements are true about the chemical reaction that forms acid rain?

a. Sulfur dioxide and nitrogen oxides react with water to form sulfuric acid and nitric acid.

b. Acid rain can cause damage to buildings and statues made of limestone or marble.

c. Acid rain is only a problem in areas with a high population density.

d. Acid rain has no effect on freshwater ecosystems."

The following waves can travel without a medium: visible light, x-rays, and radio waves. Seismic waves and waves on a lake require a medium, such as air or water, to travel through.

Visible light is a form of electromagnetic radiation that is composed of various colors. It can travel through a vacuum, such as the space between planets, and does not require a medium to travel through. X-rays are also electromagnetic radiation, but with a higher frequency than visible light, allowing them to pass through objects that visible light cannot. Radio waves are also a form of electromagnetic radiation, and can travel through a vacuum. Seismic waves, on the other hand, require a medium, such as air or rock, to travel through. These waves are used to measure earthquakes and are created when energy is released from the ground. Similarly, waves on a lake require a medium, such as water, to travel through.

Learn more about the type of waves: https://brainly.com/question/12050819

#SPJ11

The force of gravity acting between the earth and a 125-kg person standing on the surface of the earth is 1226.7N.

This is calculated using Newton's law of universal gravitation, which states that the gravitational force between two objects is equal to the product of their masses, divided by the square of the distance between them, multiplied by the gravitational constant. In this case, the masses of the Earth and the person are both known, and the distance between them is assumed to be the radius of the Earth.

Therefore, the gravitational force between the Earth and the person can be calculated as:

F = (G x ME x Mperson) / (rEarth)²

Where:

Plugging in the values, the gravitational force between the Earth and the person comes out to be 1226.7N.

.

Therefore, the force of gravity between the earth and a 125-kg person standing on the surface of the earth comes out to be 1226.7N.

To know more about the force of gravity, refer here:

https://brainly.com/question/880695#

#SPJ11

Air flow is initiated by pressure gradient force.

Pressure gradient force is the driving force behind the movement of air molecules.

When there is a difference in air pressure between two points, air molecules will move from the high-pressure region to the low-pressure region, resulting in the initiation of air flow.

Pressure gradient force is defined as the force exerted on the air by the differences in atmospheric pressure. It is the gradient of pressure that exists in the atmosphere, and it is the main driving force behind the movement of air molecules.

It is responsible for the movement of air masses from high-pressure regions to low-pressure regions. Along with the pressure gradient force, other forces also contribute to the movement of air molecules.

Friction force is a force that opposes the movement of air molecules near the Earth's surface.

Coriolis force is a force that results from the rotation of the Earth, which causes the air to deflect to the right in the Northern Hemisphere and to the left in the Southern Hemisphere.

Centrifugal force is a force that acts perpendicular to the direction of motion of the air molecules. However, it does not play a significant role in initiating air flow.

To know more about force, refer here:

https://brainly.com/question/30463106#

#SPJ4

The weather on any given day in a particular city can be sunny, cloudy, or rainy. The proportion of days that have each type of weather, in the long run, is about 29.17% of days will be sunny, 41.67% will be cloudy, and 29.17% will be rainy.

To find the proportion of days that have each type of weather in the long run, we first need to set up the transition matrix for a Markov chain using the given probabilities.

Step 1: Set up the transition matrix.
The transition matrix (P) has the format:

P = [tex]\left[\begin{array}{ccc}P(Sunny,Sunny)&P(Sunny,Cloudy)&P(Sunny, Rainy\\P(Cloudy, Sunny) &P(Cloudy, Cloudy)&P(Cloudy, Rainy)\\P(Rainy, Sunny)&P(Rainy, Cloudy)&P(Rainy,Rainy)\end{array}\right][/tex]  |

Using the given probabilities, the transition matrix is:

P =   [tex]\left[\begin{array}{ccc}3/10&1/2&1/5\\3/10&2/5&2/5\\7/10& 1/5&1/10\end{array}\right][/tex]|

Step 2: Find the long-run proportion of days for each weather type.
To find the long-run proportion of days, we need to find the steady-state probability vector (π), which satisfies the equation: πP = π

We can rewrite this as:
(πP - π) = 0
π(P - I) = 0

Where I is the identity matrix. To find π, we solve the linear system:
π(P - I) = 0

In this case, solving the system, we get:
π ≈ [0.2917, 0.4167, 0.2917]

In the long run, the proportion of days with each type of weather is approximately:
Sunny: 29.17%
Cloudy: 41.67%
Rainy: 29.17%

So, in the long run, about 29.17% of days will be sunny, 41.67% will be cloudy, and 29.17% will be rainy.

To know more about proportion refer here:

https://brainly.com/question/4545976#

#SPJ11

The given circuit has two 1.5 V batteries connected in series with a 132.5-ohm resistor. The task is to calculate the current in the circuit in milliamps (mA). Let's solve this problem step by step.

Step 1: Find the equivalent voltage of the batteries connected in series.

Voltage of one battery is 1.5 V

Total voltage = Voltage of Battery 1 + Voltage of Battery 2

Total voltage = 1.5 V + 1.5 V = 3 V

Step 2: Calculate the current in the circuit using Ohm's law, V = IR.

I = V/R

I = 3 V/132.5 Ω

I = 0.0226 A

Since the current is in Amperes (A), we have to convert it into milliamperes (mA).

1 A = 1000 mA0.0226 A = 22.6 mA

So, the current in the circuit is 22.6 mA.

To know more about the Current in a circuit, refer here:

https://brainly.com/question/12618565#

#SPJ11

The correct option is D, 1250 N force must be exerted on the smaller piston to support the load.

Surface area of larger piston = π × (radius of larger piston)²

= π × (0.08 m)²

= 0.0201 m²

Surface area of smaller piston = π × (radius of smaller piston)²

= π × (0.04 m)²

= 0.005 m²

Force on larger piston = 5000 N

Force on smaller piston = (5000 N × 0.005 m²) / 0.0201 m²

= 1250 N

Force is a quantitative description of the interaction between objects that causes a change in motion or deformation. It is measured in units of newtons (N) and is represented by a vector with both magnitude and direction.

There are four fundamental forces in nature: gravitational, electromagnetic, strong nuclear, and weak nuclear forces. Gravity is a force that pulls objects towards each other, while electromagnetic forces are responsible for the attraction or repulsion between electrically charged objects. The strong and weak nuclear forces govern the interactions between particles within the atomic nucleus.

To learn more about Force visit here:

brainly.com/question/13191643

#SPJ4

Complete Question: -

a hydraulic jack is used to lift a load of weight 5000 n. the load-bearing cylinder has a radius of 8 cm, and the other piston has a radius of 4 cm. what force must be exerted on the smaller piston to support the load?

a.100N

b.200N

c.1000N

d.1250N

e.2500N

The resistivity of the wire material can be calculated using Ohm's Law, which states that V=IR, or voltage = current multiplied by resistance. Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8} \Omega m[/tex].

Resistivity of wire is given as ρ=RA/L where R is the resistance of wire, A is the cross-sectional area of the wire, L is the length of the wire.

The formula to calculate the resistance of wire from Ohm's Law is given by R=V/I where V is the voltage, I is the current.

Substituting the given values: V = 12.0 V, I = 7.5 A.

Therefore, R=V/I=12.0 / 7.5 = 1.6 Ω

From the formula of resistivity:

[tex]\rho=\dfrac{RA}{L}\\R=\dfrac{ρL}{A}[/tex]

Substituting the given values: R = 1.6 Ω, L = 11.0 m and calculating the area:

[tex]A = (1.8 \times 10^{-3} m) (0.11 \times 10^{-3} m)\\ = 0.198 \times 10^{-6} m²[/tex]

Therefore,

[tex]\rho = RA/L\\= \dfrac{R \times A}{ L}\\= \frac{1.6 \times 0.198 \times 10^{-6}}{ 11.0}\\ = 2.87 \times 10^{-8 } \Omega m[/tex]

Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8 } \Omega m[/tex].

For more details on resistivity, click on the below link:

https://brainly.com/question/30799966

#SPJ11

This is an example of the ideal gas law, which is a combination of the three laws of thermodynamics.

The ideal gas law relates the pressure, volume, temperature, and number of particles in a gas:

PV = nRT

where;

When the car is driven, the friction between the tires and the road causes the tires to heat up. As the temperature of the air inside the tires increases, the gas particles move faster and collide more frequently with the tire walls, causing the pressure inside the tires to increase.

According to the ideal gas law, an increase in temperature causes an increase in pressure, assuming that the volume and number of particles remain constant. Therefore, the expansion of the tires due to heating is an example of the ideal gas law.

Learn more about ideal gas law here: https://brainly.com/question/12873752

#SPJ1

20 cm apart, the charges of +1.0 x 10⁻⁶ C and –1.0 x 10⁻⁶ C exert a force of 449.5 N on one another. This force is directed from the negative charge to the positive charge.

According to Coulomb's law, the force F between two point charges, q1 and q2, that are separated by a distance r, is computed as F=k|q1q2|r2.

It is possible to determine the force between two point charges using Coulomb's law:

F = k*(q1*q2)/r²

In this case, we have[tex]q1 = +10.0 x 10^-6 C, q2 = -50.0 x 10^-6 C, and r = 20 cm = 0.2 m.[/tex]

Plugging in these values, we get:

[tex]F = (8.99 x 10^9 N m^2/C^2) * [(+10.0 x 10^-6 C) * (-50.0 x 10^-6 C)] / (0.2 m)^2[/tex]

Simplifying, we get:

F = -449.5 N.

To know more about Charge visit:-

https://brainly.com/question/9194793

#SPJ1

Neutron stars with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons, are composed almost entirely of neutrons and have approximately twice the mass of the sun.

Neutron stars are composed almost entirely of neutrons and have approximately twice the mass of the sun. On average, neutron stars have about 1.4 solar masses, or 2.8 x [tex]10^3^0[/tex] kg. This means that one cubic centimeter of neutron star material has a mass of around 2.2 x [tex]10^1^4[/tex] kg. Each cubic centimeter of neutron star material contains about 1.6 x [tex]10^4^5[/tex] neutrons, or around one hundred trillion trillion neutrons. Thus, a neutron star with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons.

For more such questions on Neutron stars.

https://brainly.com/question/28271936#

#SPJ11

The minimum power output used by the athlete to climb the rope was 392.4 watts.

We can use the formula for power,

Power = Work / Time

where work is the force applied multiplied by the distance moved in the direction of the force.

The force required to lift the athlete up the rope is equal to the weight of the athlete,

Force = mass x acceleration due to gravity = 72 kg x 9.81 m/s^2 = 706.32 N

The work done by the athlete is the force multiplied by the distance moved,

Work = Force x Distance = 706.32 N x 5.0 m = 3531.6 J

Now, we can substitute these values into the formula for power,

Power = Work / Time = 3531.6 J / 9.0 s = 392.4 watts

To know more about power output, here

brainly.com/question/19052898

#SPJ4

When potential energy increases everywhere by a fixed positive value, the force magnitude does not change.

This is because potential energy is a function of position and does not depend on the force acting on the object. However, the rate of change of potential energy concerning displacement (or position) gives the force acting on the object, which is known as the force of the conservative system

Given: The potential energy increases everywhere by a fixed positive value

We know that potential energy is a function of position and does not depend on the force acting on the object.The rate of change of potential energy with respect to displacement (or position) gives the force acting on the object, which is known as the force of the conservative system.

Since the potential energy increases everywhere by a fixed positive value, it means the force magnitude does not change.

To know more about potential energy click here:

https://brainly.com/question/24284560

#SPJ11

After the collision, the first cart moves to the left with a velocity of -1.5 m/s and the second cart moves to the right with a velocity of 1.5 m/s.

The velocities of the two carts after collision can be determined using the conservation of momentum principle. Momentum is defined as the product of an object's mass and velocity. Given,Mass of each cart, m = 0.5 kg, Initial velocity of each cart, u = 1.5 m/s, Initial momentum of each cart, p = mu.

After collision, velocity of the carts = v. Using the law of conservation of momentum;

mu + mu = mv + mv⇒ 2mu = 2mv⇒ u = v

Momentum before collision = Momentum after collision (conservation of momentum)

∴ 0.5 × 1.5 + 0.5 × (-1.5) = 0.5v1 + 0.5v2

On solving, we get,v1 = -1.5 m/sv2 = 1.5 m/s

Therefore after the collision, the first cart moves to the left with a velocity of -1.5 m/s and the second cart moves to the right with a velocity of 1.5 m/s.

More on velocity: https://brainly.com/question/30470329

#SPJ11

A circuit that minimizes resistance will be able to carry the maximum amount of current.

What is Current?

It is defined as the amount of electric charge passing through a given point in a circuit in unit time. The SI unit of electric current is the ampere (A), which is defined as one coulomb of electric charge per second. Electric current can be either direct current (DC), which flows in one direction only, or alternating current (AC), which changes direction periodically.

Based on the results of this activity, a circuit that would carry the maximum amount of electric current should have:

High voltage: A higher voltage will cause a greater potential difference and push more electrons through the circuit.

Thicker wire diameter: A thicker wire diameter will have lower resistance, allowing more current to flow through the wire.

Shorter wire length: A shorter wire length will have lower resistance, allowing more current to flow through the wire.

Lower wire temperature: A lower wire temperature will have lower resistance, allowing more current to flow through the wire.

Learn more about  Current from given link

https://brainly.com/question/1100341

#SPJ1

Gravitational field near the surface of Mercury is approximately 3.7 N/kg

Gravitational field near the surface of Venus is approximately 8.87 N/kg.

Gravitational field near the surface of Mercury and Venus, we can use the formula:

gravitational field (g) = (G * M) / R^2

where G is the gravitational constant (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2)), M is the mass of the planet, and R is the radius of the planet.

For Mercury:
M = 3.29E23 kg
R = 2.44E6 m

g = (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2) * 3.29E23 kg) / (2.44E6 m)^2
g ≈ 3.7 N/kg

For Venus:
M = 4.87E24 kg
R = 6.05E6 m

g = (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2) * 4.87E24 kg) / (6.05E6 m)^2
g ≈ 8.87 N/kg

So, the gravitational field near the surface of Mercury is approximately 3.7 N/kg, and the gravitational field near the surface of Venus is approximately 8.87 N/kg.

learn more about 'gravitation':https://brainly.com/question/31276986

#SPJ11

The length of the nichrome wire that has the same resistance as the 12.0-meter copper wire is approximately [tex]\( 0.13 \, \text{m} \)[/tex].

To find the length of the nichrome wire that has the same resistance as the 12.0-meter copper wire, we can use the formula for resistance:

[tex]\[ R = \frac{{\rho \cdot L}}{{A}} \][/tex]

where [tex]\( R \)[/tex] is the resistance, [tex]\( \rho \)[/tex] is the resistivity, [tex]\( L \)[/tex] is the length of the wire, and [tex]\( A \)[/tex] is the cross-sectional area.

Given:

Length of the copper wire, [tex]\( L_c = 12.0 \, \text{m} \)[/tex]

Resistance of the copper wire, [tex]\( R_c = 1.50 \, \Omega \)[/tex]

Resistivity of copper, [tex]\( \rho_c = 1.7 \times 10^{-8} \, \Omega \cdot \text{m} \)[/tex]

Resistivity of nichrome, [tex]\( \rho_n = 1.5 \times 10^{-6} \, \Omega \cdot \text{m} \)[/tex]

Let's calculate the cross-sectional area of the copper wire using the resistance formula:

[tex]\[ A_c = \frac{{\rho_c \cdot L_c}}{{R_c}} \]\\\\\ A_c = \frac{{1.7 \times 10^{-8} \cdot 12.0}}{{1.50}} \\\\= 1.36 \times 10^{-7} \, \text{m}^2 \][/tex]

Next, we can use the resistance formula to find the length of the nichrome wire:

[tex]\[ R_n = \frac{{\rho_n \cdot L_n}}{{A_c}} \][/tex]

We need to solve for [tex]\( L_n \)[/tex]:

[tex]\[ L_n = \frac{{R_n \cdot A_c}}{{\rho_n}} \][/tex]

Substituting the given values:

[tex]\[ L_n = \frac{{1.50 \cdot 1.36 \times 10^{-7}}}{{1.5 \times 10^{-6}}} \\\\= 0.13 \, \text{m} \][/tex]

Therefore, the length of the nichrome wire that has the same resistance as the 12.0-meter copper wire is approximately [tex]\( 0.13 \, \text{m} \)[/tex].

Know more about nichrome wire:

https://brainly.com/question/31111150

#SPJ12

In the metric system, air pressure is measured in pascals. One pascal is equal to a force of one newton per square meter.

Air pressure can be measured using different units. Pascal is a unit of pressure, defined as one newton per square meter. This unit is named after Blaise Pascal, a French mathematician, physicist, and philosopher who made important contributions to the fields of hydrodynamics and hydrostatics.

In the US customary system, air pressure is measured in pounds per square inch (psi), while in the International System of Units (SI), it is measured in pascals (Pa). The unit psi is used to measure pressure in liquids and gases, and it is defined as the amount of pressure exerted by a force of one pound-force per square inch.

Learn more about pascal unit at https://brainly.com/question/30777634

#SPJ11

The voltage across the inductor during the period when the current changes at 9.1 A/ms with an inductance of 26 mH is 236.6 V.

An inductor is an electrical component that stores energy in a magnetic field when a current passes through it. An inductor is a device that opposes any change in the current flowing through it. The inductor is represented by the symbol L and is measured in henries (H).

The difference in electrical potential between two points in a circuit is known as voltage. The unit of voltage is volts (V).

The voltage across an inductor can be calculated using the formula:

[tex]v = L(di/dt)[/tex]

where v is the voltage, L is the inductance, and [tex]di/dt[/tex] is the rate of change of current.

Substituting the given values, we get:

[tex]v = 26\  mH \times (9.1 \ A/ms)[/tex]

Note that the units for inductance and rate of change of current must be consistent, so we convert the inductance to henries (H) and the rate of change of current to amps per second (A/s):

[tex]v = 0.026\  H \times (9100 \ A/s)[/tex]

[tex]v = 236.6 \ V[/tex]

Therefore, the voltage across the inductor during this period is 236.6 V.

Learn more about inductance:

https://brainly.com/question/30216563

#SPJ11

The net force acting on the box is 18 N

The net force acting on the box is the vector sum of forces f1 and f2. The net force is given by the formula:
F_net = F_1 + F_2

where F_net is the net force and F_1 and F_2 are the individual forces.

F_1 has a magnitude of 7 N and F_2 has a magnitude of 11 N. Therefore, the net force, F_net, has a magnitude of 18 N and can be expressed as:
F_net = 7 N + 11 N = 18 N

This means that the box is experiencing a net force of 18 N.

Imagine two arrows pointing in opposite directions, with the magnitude of each arrow indicating the magnitude of the respective force. When added together, the arrows should result in an arrow with a magnitude of 18 N.

This new arrow indicates the direction and magnitude of the net force acting on the box.

The net force is calculated by adding the vectors F_1 and F_2. This is done by adding the x and y components of each vector.

In this example, both F_1 and F_2 are in the same direction, so only the magnitudes are added to get the net force.

This is how it works: F_net = 7 N + 11 N = 18 N.

The net force acting on the box is 18 N and is the vector sum of forces f1 and f2.

to know more about Force refer here:

https://brainly.com/question/13191643#

#SPJ11

The number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

Speed Ratio: Speed Ratio = (Number of Teeth on Driven Gear)/(Number of Teeth on Driving Gear). The Speed Ratio = 1400 rev/min/2100 rev/min = 0.6667.

Therefore, the number of teeth on the driven gear = (Number of Teeth on Driving Gear) x (Speed Ratio) = 20 x 0.6667 = 13.33. Rounding up, we can conclude that the number of teeth on the driven gear is 14.

The next step is to find the theoretical center-to-center distance. To do this, we need to use the formula for calculating Pitch Diameter: Pitch Diameter = (Number of Teeth)/(Diametral Pitch).

In this case, the Pitch Diameter of the driving gear is (20 teeth)/(12 teeth/in) = 1.67 inches. Therefore, the center-to-center distance = Pitch Diameter x 2 = 1.67 inches x 2 = 3.34 inches.

Hence the number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

to know more about distance refer here:

https://brainly.com/question/15172156#

#SPJ11

The Richter scale measures the energy released by an earthquake, while the Mercalli scale measures the intensity of the earthquake based on its effects. The Richter scale is useful for measuring small to moderate earthquakes, while the Mercalli scale is useful for measuring the effects of large earthquakes.

The Richter scale and Mercalli scale are both used to measure earthquakes, but they differ in the following ways:

Richter Scale: This scale measures the magnitude or energy released by an earthquake at its epicenter.

It is a logarithmic scale, which means that an increase of one unit on the scale corresponds to a tenfold increase in the magnitude of the earthquake.

The scale ranges from 1 to 10, but there is no upper limit.

The Richter scale is useful for measuring small to moderate earthquakes, but it is less accurate for large earthquakes.

Mercalli Scale: The Mercalli scale measures the intensity of an earthquake based on the damage it causes and how people feel it.

The scale ranges from I to XII and is divided into two parts: the first part measures the effects of the earthquake on buildings and other structures, while the second part measures the effects of the earthquake on people and animals.

The Mercalli scale is useful for measuring the effects of large earthquakes, but it is less accurate for small earthquakes.

For similar question on earthquakes

https://brainly.com/question/30100514

#SPJ11

The speed of the boat in still water is 34 km/h, and the speed of the stream's current is 8 km/h.

Let's denote the speed of the boat in still water as v and the speed of the stream's current as c.

When the boat travels downstream, its speed relative to the shore is the sum of its speed in still water and the speed of the current. So, we have:

v + c = 84 km/2 h = 42 km/h

When the boat travels upstream, its speed relative to the shore is the difference between its speed in still water and the speed of the current. So, we have:

v - c = 130 km/5 h = 26 km/h

We can now solve this system of equations to find v and c. Adding the two equations, we get:

2v = 68

v = 34 km/h

Substituting v into one of the equations, we can solve for c:

v + c = 42

34 + c = 42

c = 8 km/h

Learn more about  speed of the stream's at: https://brainly.com/question/2292122

#SPJ11

The sun's magnetic field is responsible for the sun's surface and atmospheric activity. The correct option is "The sun's magnetic field."The sun's magnetic field plays a vital role in the surface and atmospheric activity of the sun.

The sun is considered a magnetized body that possesses a strong magnetic field. Magnetic fields are present in every part of the sun, from the core to the atmosphere, and they play a crucial role in the sun's structure, dynamics, and atmosphere.The sun's magnetic field is responsible for the following phenomena:

Sunspots are dark areas on the surface of the sun that are cooler than the surrounding areas, but they are still very hot. They arise because of the interaction between the sun's magnetic field and the sun's plasma.Auroras occur when charged particles from the sun collide with particles in the Earth's atmosphere, and the interaction between the particles' magnetic fields produces a beautiful display of light in the sky.

The corona, which is the sun's outermost layer, is hotter than the layers below it. The sun's magnetic field is thought to be responsible for the heating.

for such more question on magnetic field

https://brainly.com/question/14411049

#SPJ11

The student added 1,700,000 Joules of heat to the water.

What is Specific Heat?

Specific heat is the amount of heat energy required to raise the temperature of one unit mass of a substance by one degree Celsius (or Kelvin) without any change in phase. It is a physical property of a substance that is unique to each material and depends on its molecular structure and composition. The specific heat of water, for example, is 4.18 J/g°C, which means that it takes 4.18 joules of energy to raise the temperature of one gram of water by one degree Celsius.

The heat added to the water can be calculated using the formula:

Q = m * c * ΔT

where Q is the heat added, m is the mass of the water, c is the specific heat of water, and ΔT is the change in temperature.

Substituting the given values:

m = 5 kg

c = 4,000 J/kg°C

ΔT = (100°C - 15°C) = 85°C

Q = 5 kg * 4,000 J/kg°C * 85°C = 1,700,000 J

Therefore, the student added 1,700,000 Joules of heat to the water.

Learn more about Specific Heat from given link

https://brainly.com/question/27991746

#SPJ1

When a body of mass 2.00 kg is pushed straight upward by a 25.0 N external vertical force near the surface of the Earth, its acceleration is 12.5 m/s2. This is equal to the acceleration due to gravity (g).

The acceleration of a body of mass 2.00 kg when pushed straight upward by a 25.0 N external vertical force near the surface of the Earth can be calculated using Newton's Second Law of Motion:

F = ma. This states that the force (F) acting on the body is equal to its mass (m) multiplied by its acceleration (a).

Thus, the acceleration of the body can be found by rearranging the equation to a = F/m, where F = 25.0 N and m = 2.00 kg. This gives an acceleration of 12.5 m/s2.

This acceleration is the same as the acceleration due to gravity (g). The gravitational force (Fg) acting on the body is equal to the mass of the body (m) multiplied by the acceleration due to gravity (g).

Therefore, Fg = mg = (2.00 kg)(9.80 m/s2) = 19.6 N. Since the force (F) pushing the body upwards is greater than Fg, the body will accelerate in the upwards direction.

This is why the acceleration of the body (a) is equal to 12.5 m/s2.

to know more about acceleration refer here:

https://brainly.com/question/30660316#

#SPJ11

The acceleration due to gravity in m/s² at that altitude of 744 km is 9.797.

To find out what the acceleration due to gravity is in m/s² at an altitude of 744 km above the surface of earth, use the formula `g = Gm/r²`.

Given,The altitude of the satellite, h = 744 km,The radius of the earth, r = 6371 km, Formula for acceleration due to gravity:

g = Gm/r²

Here, the value of G, the universal gravitational constant, is 6.67 x 10^-11 Nm²/kg².Mass of the Earth, m = 5.97 x 10^24 kg.Let's calculate the radius of the orbit, R.Radius of the orbit = r + h= 6371 + 744 = 7115 km = 7.115 x 10^6 m.So, we have,

g = Gm/R²= 6.67 x 10^-11 x 5.97 x 10^24 / (7.115 x 10^6)²= 9.797 m/s².Therefore, the acceleration due to gravity in m/s² at that altitude is 9.797.

More on acceleration: https://brainly.com/question/21975712

#SPJ11

The rotational inertia of an object depends on its mass distribution and shape relative to the axis of rotation. To calculate the rotational inertia of the system, we would need to know the shapes and masses of the rotating arm and sliding masses.

Rotational inertia depends on the object's mass distribution and the axis of rotation. The greater the object's mass is concentrated away from the axis of rotation, the greater the rotational inertia. The moment of inertia of a rigid body is defined as the sum of the products of the mass of each particle in the body and the square of its distance from the axis of rotation.

Rotational inertia plays a crucial role in many physical phenomena involving rotation, such as the behavior of rotating machines, the motion of planets and stars, and the stability of objects in motion. Understanding rotational inertia is essential for designing efficient and effective machines and for predicting the behavior of rotating systems.

To learn more about Rotational inertia visit here:

brainly.com/question/30856540

#SPJ4