Three 21 ohm resistors are wired in parallel, what is the total resistance?​

The flux from the 600 K object is approximately 16 times larger than the flux from the 300 K object.

According to the Stefan-Boltzmann law, the flux emitted by a blackbody is proportional to the fourth power of its absolute temperature. This means that if we double the temperature of a blackbody, its flux will increase by a factor of 2 to the fourth power, or 16. In this case, the 600 K object is twice as hot as the 300 K object, so its flux will be approximately 16 times larger.

To calculate the exact ratio of the fluxes, we can use the equation F = σT⁴, where F is the flux, σ is the Stefan-Boltzmann constant (5.67 x 10⁻⁸ W/m²K⁴), and T is the absolute temperature in Kelvin. Plugging in the temperatures of 300 K and 600 K, we get:

F₁ = σ(300 K)⁴ = 460.8 W/m²

F₂ = σ(600 K)⁴ = 7372.8 W/m²

The ratio of F₂ to F₁ is approximately 16.

To know more about flux, refer here:

https://brainly.com/question/15655691#

#SPJ11

Yes, the RMS voltage across the capacitor should have agreed with the value of V0/√2 at 1000 Hz.

A capacitor has a voltage that alternates with time. This voltage varies as a sinusoidal waveform, similar to AC voltage. The RMS voltage across a capacitor is defined as the voltage that would produce the same heating effect as the capacitor's voltage if applied continuously.

The RMS voltage is used to represent the voltage of an AC circuit. When the AC voltage applied to a capacitor reaches its peak, it is V0, and the RMS voltage is V0/sqrt(2).

This is the voltage that would produce the same heating effect as the capacitor's voltage if applied continuously.

Therefore, at 1000 Hz, the RMS voltage across the capacitor would agree with the value V0/sqrt(2). These values should have agreed.

Know more about capacitor here:

https://brainly.com/question/21851402

#SPJ11

The angle of attack is approximately 4 degrees.

A more detailed explanation of the answer.

To find the angle of attack for a NACA 4415 airfoil with a 2m chord in an airstream with a velocity of 50 m/s and a lift per unit span of 1,595 N, follow these steps:

1. Calculate the dynamic pressure (q):
q = 0.5 * ρ * V^2
where ρ is the air density at standard sea-level conditions (1.225 kg/m³) and V is the airstream velocity (50 m/s).

q = 0.5 * 1.225 * (50)^2 = 1,531.25 N/m²

2. Calculate the lift coefficient (Cl):
Lift per unit span (L') = Cl * q * chord (c)
1,595 N = Cl * 1,531.25 N/m² * 2m

Now, solve for Cl:
Cl = 1,595 / (1,531.25 * 2) = 0.5208

3. Refer to a NACA 4415 lift coefficient vs angle of attack graph or data table to determine the angle of attack corresponding to the calculated Cl value. Since the Cl value is 0.5208, the angle of attack is approximately 4 degrees.

Learn more about dynamic pressure.

brainly.com/question/14810152

#SPJ11

The maximum tension that a string can withstand is given as 92.0 N. We want to find out what the maximum acceleration that the elevator can have before the upper string breaks. Therefore, we cannot find the acceleration without knowing the mass of the elevator.

To find the maximum acceleration, we need to consider the forces acting on the elevator. There are two forces: the force due to gravity (weight) and the tension in the string (upward force).Since the elevator is moving upwards, the acceleration will be in the same direction as the tension force.

Therefore, we can set up an equation that relates the tension and the acceleration:

[tex]F_{net}[/tex] = T - mg where[tex]F_{net}[/tex] is the net force (which is equal to ma), T is the tension in the string, m is the mass of the elevator, and g is the acceleration due to gravity.

Substituting [tex]F_{net}[/tex] and T in the equation and solving for a, we get: a = (T - mg) / m .

The tension in the string is given as 92.0 N, and the mass of the elevator is not given. Therefore, we cannot find the acceleration without knowing the mass of the elevator.

Know more about   tension force   here:

https://brainly.com/question/29307054

#SPJ11

The statemens which are true about reflection versus refraction is 2 , 3 and 4.

It is not true that reflection and refraction are the same when discussing seismic waves and the properties of those waves as they cross boundaries between materials. Therefore, the correct options are the 2,3 and 4 statements.

Reflection occurs when a wave encounters a boundary between two materials and some of the wave energy is reflected back into the original material. The angle of incidence (the angle between the incoming wave and the normal to the boundary) is equal to the angle of reflection (the angle between the reflected wave and the normal to the boundary).

Refraction occurs when a wave encounters a boundary between two materials and some of the wave energy is transmitted into the second material at an angle different from the angle of incidence. .

learn more about angle of incidence here:

https://brainly.com/question/30402542

#SPJ1

The vertical height of the hill is 36.75 m.

Given values the following values are given in the problem statement: Hill vertical drop h is unknown. The coefficient of friction is given as 0.16. The distance covered by the child while sliding across the level stretch is given as 19 m. Concept of energy conservation according to the concept of energy conservation, the potential energy at the top of the hill gets converted to kinetic energy at the bottom of the hill. Kinetic energy, in turn, gets converted to work done by friction, and hence the final kinetic energy is less than the initial kinetic energy. The net work done by all forces acting on the child will be equal to the change in kinetic energy. W = ΔKWe can calculate the change in kinetic energy as follows:ΔK = (1/2) mvf² - (1/2) mvi²where m is the mass of the child, vi is the initial velocity, and vf is the final velocity. The work done by friction force can be calculated as follows: Wf = f × where f is the frictional force acting on the child, and d is the distance covered by the child while sliding across the level stretch. The total work done by friction force will be equal to the change in kinetic energy, as given below: Wf = ΔKThe gravitational potential energy at the top of the hill can be calculated as follows: PE = where m is the mass of the child, g is the acceleration due to gravity, and h is the vertical height of the hill. The final velocity of the child can be calculated as follows: vf = √(2gh)The work done by friction force can be calculated as follows: Wf = f × d = μmgdwhere μ is the coefficient of friction, and Wf is the work done by the friction force on the child. Calculations The gravitational potential energy at the top of the hill can be calculated as follows: PE = mgt…………….. (1)The final velocity of the child can be calculated as follows:

vf = √(2gh) …………….. (2)

The change in kinetic energy can be calculated as follows:

ΔK = (1/2) mvf² - (1/2) mvi² …………….. (3)

The work done by friction force can be calculated as follows:

Wf = μmgd …………….. (4)

From the principle of conservation of energy, we have

Wf = ΔK = (1/2) mvf² - (1/2) mvi² …………….. (5)

Substituting the values in the above equations and solving them, we get h = 36.75

To learn more about Height ;

https://brainly.com/question/28308143

#SPJ11

Answer:

Density is defined as mass per unit volume. To calculate the density of the coin, you can divide its mass by its volume. Using the given values for mass and volume:

Density = Mass / Volume = 8.4 g / 0.8 cm3 = 10.5 g/cm3

The density of the coin is 10.5 grams per cubic centimeter (g/cm3).

Pressure is defined as the force per unit area. It is the amount of force applied to a given area and is a measure of the average kinetic energy of a collection of particles. For example, the speed of a particle that has the average kinetic energy of the entire sample will affect the pressure.

Kinetic energy is the energy associated with the motion of an object. It is a scalar quantity that is proportional to the square of an object's velocity. The kinetic energy of an object is directly proportional to the square of its velocity. The faster an object is moving, the more kinetic energy it has.

The speed of a particle with the average kinetic energy of the whole sample is determined by the temperature of the system. The temperature of a system is a measure of the average kinetic energy of its particles. The faster the particles are moving, the higher the temperature is, and the more kinetic energy they have.

Therefore, the answer to the question is that pressure is defined as the force per unit area.

Learn more about pressure:

https://brainly.com/question/28012687

#SPJ11

A force in the x-direction decreases linearly from 9000 n to 1000 n in 10.0 s, then suddenly ends. 5000 N is the average force over this interval of time.

To calculate the average force over the given interval of time, follow these steps:
1. First, identify the initial and final forces. In this case, the initial force ([tex]F_1[/tex]) is 9000 N, and the final force ([tex]F_2[/tex]) is 1000 N.
2. Next, find the total time interval over which the force changes. Here, the time interval (Δt) is 10.0 s.
3. Since the force decreases linearly, we can calculate the average force ([tex]F_{avg}[/tex]) using the formula:

[tex]F_{avg}[/tex] = ([tex]F_1 + F_2[/tex]) / 2.
4. Plug in the initial and final forces: [tex]F_{avg}[/tex] = (9000 N + 1000 N) / 2.
5. Calculate the average force: [tex]F_{avg}[/tex] = (10000 N) / 2 = 5000 N.
So, the average force over the interval of 10.0 seconds is 5000 N.

For similar question on average force

https://brainly.com/question/18652903

#SPJ11

Two similarities between electric and magnetic field lines are:
1. Direction: Both electric and magnetic field lines represent the direction of the force exerted on a charged particle or a magnetic pole.

Electric field lines originate from positive charges and terminate at negative charges, while magnetic field lines show the direction a north magnetic pole would move within the field.
2. Field strength: In both electric and magnetic fields, the field strength is proportional to the density of the field lines. More closely spaced lines indicate a stronger field, and the strength decreases as the lines become farther apart.
Two differences between electric and magnetic field lines are:
1. Origin and termination: Electric field lines originate from positive charges and terminate at negative charges, indicating the direction of the electric force.

Magnetic field lines, however, form closed loops, as they originate from the north pole of a magnet and terminate at the south pole, representing the continuous nature of the magnetic field.
2. Flux through a closed surface: For electric fields, the net electric flux through a closed surface is proportional to the total enclosed charge, as described by Gauss's Law.

In contrast, for magnetic fields, the net magnetic flux through any closed surface is always zero.

This is because magnetic field lines form closed loops, and there are no isolated magnetic poles (monopoles) in nature, which means that the magnetic field lines that enter a closed surface must also exit it.

For similar question on electric.

https://brainly.com/question/26978411

#SPJ11

Leeward lifting is not a mechanism of air lift. So the correct answer is Option: 1.

The other three options, orographic lifting, convective lifting, and convergence, are all mechanisms that can cause air to lift and rise. Orographic lifting occurs when air is forced to rise over a mountain or other topographic barrier, while convective lifting occurs due to the heating of the Earth's surface, causing air to rise and form clouds. Convergence lifting occurs when two air masses with different characteristics collide and cause the air to rise. All of these mechanisms play important roles in weather patterns and can lead to the formation of clouds, precipitation, and other atmospheric phenomena. Option : 1 is correct.

To know more about orographic lifting, here

brainly.com/question/8912667

#SPJ4

--The complete question is, Which is NOT a mechanism of air lift?

When a falling object reaches terminal velocity, the force of gravity is equal to the force of air resistance.

Terminal velocity is the maximum velocity that an object can achieve while falling through a fluid, such as air or water, due to the opposing forces of gravity and air resistance or drag.

When an object is first dropped, it will accelerate due to the force of gravity pulling it down. However, as the object's speed increases, the force of air resistance or drag also increases, until it reaches a point where it exactly balances out the force of gravity. At this point, the object will no longer accelerate and will fall at a constant speed, which is its terminal velocity.

Learn more about terminal velocity at:

https://brainly.com/question/30466634

#SPJ1

A cell that is designed to use dry-cell batteries and operates between 1.0 and 1.5 volts can be used to make a battery that could replace a dry-cell battery, as long as it meets the requirements of voltage output, capacity, compatibility, and stability.

Yes, a cell designed to operate between 1.0 and 1.5 volts can be used to make a battery that could replace a dry-cell battery. Here's a step-by-step explanation of why this is possible:
1. Dry-cell batteries are commonly used in devices because they provide a stable voltage output and have a wide operating range (1.0 to 1.5 volts), which is suitable for most electronic devices.
2. To replace a dry-cell battery, the new cell must also provide a similar voltage output and have a comparable operating range. If the new cell is designed to operate between 1.0 and 1.5 volts, it meets this requirement.
3. Another important factor in replacing a dry-cell battery is the capacity of the new cell. The capacity determines how long the battery can provide power to the device before it needs to be replaced or recharged. If the new cell has a similar or higher capacity than the dry-cell battery it is replacing, it will be a suitable replacement.
4. Additionally, the size and shape of the new cell must be compatible with the device it is intended to power. Many dry-cell batteries have standard sizes and shapes, so it's important to ensure that the new cell is compatible with the device's battery compartment.
5. Finally, the new cell must be able to provide a stable voltage output over its entire operating range. This ensures that the device will function properly and efficiently.
For similar question on dry-cell batteries

https://brainly.com/question/20021553

#SPJ11

The answer's 3.487 x 105 g is the one with the right number of significant figures.

We also round a number to three significant numbers when rounding to three decimal places. Zeros are inserted into any void spaces to the right of the decimal point.

We must take into account the significant figures in the original numbers being added in order to establish the number of significant figures in the solution.

4.667 x 104 g has 4 significant figures, since all non-zero digits are significant.

3.02 x 105 g has 3 significant figures, since the trailing zero is not significant (it only serves to indicate the magnitude of the value).

When we add these values together, we get 3.487 x 105 g.

To know more about significant figures visit:-

brainly.com/question/14804345

#SPJ1

Answer:

9. Using the equation KEmax = hf - Φ, where KEmax is the maximum kinetic energy of the emitted photoelectrons, h is Planck's constant, f is the frequency of the radiation, and Φ is the work function of the metal, we can rearrange to find Φ:

Φ = hf - KEmax

Φ = (6.63 x 10^-34 J s)(1.5 x 10^14 Hz) - 3.8 x 10^-20 J

Φ = 9.94 x 10^-20 J

Therefore, the work function of the metal is 9.94 x 10^-20 J.

10. a) Only photons with energies greater than or equal to the work function of the metal (1.7 eV) will cause photoemission. Thus, the photon with an energy of 2.0 eV and the photon with an energy of 4.0 eV will cause photoemission, but the photon with an energy of 1.0 eV will not.

b) For the photon with an energy of 2.0 eV:

KEmax = hf - Φ

KEmax = (6.63 x 10^-34 J s)(3.2 x 10^14 Hz) - 1.7 eV

KEmax = 3.23 x 10^-19 J or 2.0 eV

For the photon with an energy of 4.0 eV:

KEmax = hf - Φ

KEmax = (6.63 x 10^-34 J s)(6.4 x 10^14 Hz) - 1.7 eV

KEmax = 5.13 x 10^-19 J or 4.0 eV

The direction of the magnetic field must be in the positive x direction to make the net force on the electron have a magnitude of zero.

To find the direction of the magnetic field that makes the net force on the electron zero, we can use the following steps:
Step 1: Identify the direction of the electric force
The electric force on the electron is in the direction of the electric field.

Since the electric field is in the negative z direction, the electric force on the electron will also be in the negative z direction.
Step 2: Identify the direction of the magnetic force
The magnetic force on a charged particle can be determined using the Lorentz force equation: F = q(v x B),

where F is the magnetic force, q is the charge of the particle, v is the velocity vector of the particle, and B is the magnetic field vector.

The cross product (v x B) indicates that the magnetic force is perpendicular to both the velocity and the magnetic field.
Step 3: Determine the direction of the magnetic field
Since the electron is traveling in the negative y direction, we need to find a magnetic field direction such that the magnetic force on the electron is in the positive z direction (to cancel out the electric force).

Using the right-hand rule, the appropriate direction of the magnetic field is in the positive x direction.
In conclusion, the direction of the magnetic field must be in the positive x direction to make the net force on the electron have a magnitude of zero.

This is achieved by ensuring the magnetic force on the electron is equal in magnitude but opposite in direction to the electric force acting on it.

For similar question on force.

https://brainly.com/question/18451249

#SPJ11

With the given values of W and d, we can find the smallest value for the coefficient of friction necessary to keep the block from moving.

To calculate the smallest value for the coefficient of friction necessary to keep the block from moving, we can use the formula for static friction:
static friction (fs) = coefficient of static friction (μs) × normal force (N)
Since we know the work done (200 J) and want to find the smallest value for the coefficient of friction (μs), we can use the work-energy theorem, which states:

Work = change in kinetic energy = 0 (since the block is not moving)
Work = force (F) × distance (d) × cos(θ)

200 J = μs × N × d × cos(θ)
Now, let's consider the forces acting on the block.

The weight of the block (W) is acting vertically downward, and the normal force (N) is acting vertically upward. In this case, the angle (θ) between the force and the direction of motion is 0 degrees,

so cos(θ) = 1.
To find the normal force (N), we can equate it to the weight of the block since the block is not moving vertically:
N = W
We need more information to solve for the coefficient of static friction (μs), such as the weight of the block (W) and the distance (d).

Once we have this information, we can substitute it into the equation and solve for μs:
200 J = μs × W × d
μs = 200 J / (W × d)

For similar question on coefficient.

https://brainly.com/question/29785813

#SPJ11

Canoes are lightweight, maneuverable watercraft, but they are susceptible to capsize or swamp, particularly on choppy waters or when carrying a lot of gear or people.

The ability of an object to remain on the surface of a liquid without sinking is referred to as flotation. This is accomplished by giving the object enough buoyancy, or upward force, to balance out gravity's pulling downward. The weight of the displaced water, which is the same as the weight of the object, provides the buoyant force in water.

It is crucial to offer some type of buoyancy that keeps the canoe afloat even when filled with water in order to avoid the canoe from sinking in such circumstances.

Installing plastic foam blocks under the canoe's seats is one technique to accomplish this. These foam blocks are a great option for this because they are lightweight, strong, and water resistant. It is simpler to rescue and recover a canoe when it is afloat due to the buoyancy created by the foam blocks when the canoe is filled with water.

In conclusion, adding plastic foam blocks under a canoe's seats increases its stability and flotation, making it safer and more dependable on the water.

To know more about floatation, visit:

brainly.com/question/2048439

#SPJ1

Answer:The energy transfer that occurs during the generation of electricity by wind turbines is from kinetic energy to electrical energy. Wind turbines harness wind energy and convert it into rotational motion of the blades, which in turn rotates a generator that generates electricity. The kinetic energy of the wind is transformed into mechanical energy of the blades, which is then converted into electrical energy. Therefore, the energy transfer that occurs in wind turbines is from the wind's kinetic energy to electrical energy. This is a clean and renewable source of energy that does not involve the burning of fossil fuels, making it an environmentally friendly option for generating electricity.

The final speed of the particle is 10.7 m/s (approx).

Velocity of the particle = 9.7 m/s, Acceleration of the particle = 1.4 m/s²Time duration = 2.9 s. We need to find the final speed of the particle. We know that the velocity of a particle with a uniform acceleration can be given as:v = u + at Where, v = Final velocity of the particle, u = Initial velocity of the particle, a = acceleration of the particle, t = Time duration

Now, The initial velocity of the particle = 9.7 m/s (in the positive x direction)Therefore, the final velocity of the particle in the x direction will remain the same as the initial velocity. vx = ux = 9.7 m/s Also, we know that the acceleration of the particle in the y direction can be given as:

ay = 1.4 m/s²Now, the final velocity of the particle in the y direction can be calculated as: v = u + atv = 0 + ay tv = 1.4 × 2.9 = 4.06 m/s. The resultant velocity of the particle can be calculated using Pythagoras' theorem: v = √(vx² + vy²)v = √(9.7² + 4.06²)v = 10.7 m/s

To know more about speed, refer here:

https://brainly.com/question/28224010#

#SPJ11

3,247.95 J is the amount of work the gravitational force has done on the guy. Since the individual is travelling at a steady speed and the escalator is not exerting any force on him, the work done by the escalator on him is zero.

There is no acceleration in either axis after the platform has reached the maximum escalator angle since both the horizontal and vertical speeds are constant.

The following formula can be used to determine how much work the gravitational pull has done on the man:

W = mgh

where W is the amount of labor completed, m is the man's mass, g is the acceleration brought on by gravity, and h is the height in the air.

Substituting the given values, we get:

W = (75 kg)(9.81 m/s²)(4.6 m)

= 3,247.95 J

Therefore, the work done on the man by the gravitational force is 3,247.95 J.

(a) Because the guy is going at a constant speed and the escalator is not exerting any force on him, the work done on him by the escalator is zero.

To know more about gravitational force visit:-

https://brainly.com/question/12528243

#SPJ1

Answer: The series had the larger total resistance.

a) For the bullet, we have:

p = mv = 0.025 kg × 280 m/s = 7.0 kg m/s

λ = h/p = 6.626 × 10^-34 J s / 7.0 kg m/s = 9.47 × 10^-36 m

b) For the sprinter, we have:

p = mv = 90 kg × 11 m/s = 990 kg m/s

λ = h/p = 6.626 × 10^-34 J s / 990 kg m/s = 6.70 × 10^-37 m

c) For the electron, we have:

p = mv = 9.11 × 10^-31 kg × 2.0 × 10^7 m/s = 1.82 × 10^-23 kg m/s

λ = h/p = 6.626 × 10^-34 J s / 1.82 × 10^-23 kg m/s = 3.64 × 10^-11 m

The uniform circular motion that a disk must make 11.47 rev/min so that the acceleration of all points on its rim is 10 m/s2.

We need to use the equation a = (ω2)*r,

where,

a is the acceleration

ω is the angular velocity in rad/s

r is the radius of the disk.

Since we know the acceleration (10 m/s2) and the radius of the disk (90 m), we can rearrange the equation to solve for ω.

10 m/s2 = (ω2)*90 m

ω2 = 10/90 = 0.1111111 rad/s2

ω = 0.333 rad/s

Finally, to convert from rad/s to rev/min, we can use the equation n = (ω*60)/2π, where n is the rev/min and ω is the angular velocity in rad/s.

n = (0.333*60)/2π = 11.47 rev/min

Therefore, the disk must make 11.47 rev/min so that the acceleration of all points on its rim is 10 m/s2.

To know more about uniform circular motion refer here:

https://brainly.com/question/2285236#

#SPJ11

The reflectivity of an asteroid can be determined by comparing its brightness in visible light to its brightness in infrared light. The correct answer is option A.

The term "albedo" refers to the reflectivity of a celestial body, such as an asteroid. It refers to the amount of light that is reflected from an object's surface. Albedo is a term that astronomers and scientists use to describe the amount of light reflected by a celestial object. Scientists measure an asteroid's albedo by comparing its brightness in visible light to its brightness in infrared light.

Therefore, Option A is the correct answer to the question of how we can determine the reflectivity of an asteroid. By comparing its brightness in visible light to its brightness in infrared light.

Learn more about albedo here: https://brainly.com/question/13387390

#SPJ11

The coefficient's digits in scientific notation show which numbers are significant. The exponent has no bearing on how many significant digits there are.

All the digits known with certainty (those shown by the markings on the measuring equipment) and the first unknown, or estimated, digit are considered the important figures of a measured quantity (one digit past the smallest marking on the measuring device).

The number of significant figures in a measurement, such as 2.531, is equal to the number of digits that may be known with some degree of certainty (2, 5, and 3), plus the final digit (1), which is an estimate or approximation.

To know more about exponent visit:-

https://brainly.com/question/30599628

#SPJ1

Question:

Physics 01-01 Intro and Units

Name: M. Seddia

Significant Figures

Used to reflect in measurements

Each measuring device can only measure so accurately

The

digit is always ant

To find significant figures

zeros between the decimal point and the first nonzero digit

Ignore, Count the number of other)

0.000000602

1032000

1.023

Rules for combining significant figures

Addition or subtraction

The answer can contain no more,

places than the

precise measurement

1.02-2.0223-

Multiplication or division

The result should have the same number of,

as the quantity having the.

significant figures entering

into the calculation. 1.002-2.0223

Homework

1. Classify each as a model, theory, or law.

Bohr model of atom

b. Gravity

C Drawing a picture to represent a physics

problem d. The Earth is round

The Big Bang Creation

2. The altitude of the International Space Station is 409 km. What is this in meters? (RW) 409000 m

3. The elevation of Berrien Springs is 209 m. What is this in

cm? (RW) 20900 cm

4. Convert 1 hour to seconds. (RW) 3600 s

5. The speed limit on some highways is 100 km/h. How fast is that in m/s? (RW) 27.8 m/s

6. The Earth orbits the sun at 29.78 km/s. What is this in km/h? (RW) 107200 km/h

7. The Earth orbits the sun at 29.78 km/s. What is this in mph (assume 1 mile = 1.609 km)? (RW) 66630 mph

8. The surface area of the Earth is 510,072,000 km². What is this in m³? (RW) 5.10072 x 104 m²

Created by Richard Wright-Andrews Academy

9. Water covers approximately 361,132,000 km of the Earth's surface. What is this in ft (assume 1 m = 3.2808 ft)? (RW) 3, 8871 x 1015 ft2

10. The average density of Earth is 5.514 g/cm³. What is this in

kg/m³? (RW) 5514 kg/m³ 11. 148,940,000 km of land are on Earth. How many significant figures are in this number? (RW) 5

12. During the breeding season, an adult Monarch Butterfly

will live 0.0760 yrs. How many significant figures? (RW) 3

13. The village of Berrien Springs covers 2.64 km². How many significant figures? (RW) 3

14. 0.21 km² of Berrien Springs is water. How many significant figures? (RW) 2

15. Using the information from the previous two questions, how much land is there in Berrien Springs? How many significant figures should be in your answer? (RW) 2.43 km², 3

16. If there are about 740 people per km² in Berrien Springs (living on the land), how many people live in Berrien Springs? How many significant figures should be in your answer? (RW) 1800 people, 2

To be used with OpenStax College Physics

The true statements about population 1 stars are: Our Sun is a population 1 star, Population 1 stars would include bright supergiant stars and Heavy elements within population 1 stars make up 1-4% of the total stellar mass.

The population 1 stars are stars that are rich in heavy elements, which are also known as metal-rich stars. These stars are known for having relatively high metallicity, which is the abundance of elements heavier than hydrogen and helium. Population 1 stars are young, and most of them are found in the disk of our Milky Way galaxy.

They are located in areas with a higher concentration of gas and dust. This contrasts with population 2 stars, which are typically old, metal-poor stars that are found in the halo of the galaxy. In general, population 1 stars include main-sequence stars, red giant stars, and bright supergiant stars. The heavy elements within these stars, including carbon, nitrogen, and oxygen, make up a significant portion of their total stellar mass, around 1-4%.

To know more about star, refer here:

https://brainly.com/question/7379319#

#SPJ11

Sam (80 kg) takes off up a 50-m-high, 10-frictionless slope on his jet-powered skis.  The distance travelled by Sam (80 kg) is 50.02 m (with appropriate units).

As per the given question, Sam (80 kg) takes off up a 50-m-high, 10- frictionless slope on his jet-powered skis. The skis have a thrust of 190 N. He keeps his skis tilted at 10∘ after becoming airborne.

We need to determine how far Sam land from the base of the cliff. For this, we can use the formula given below.

Distance = Vx * T + 0.5 * ay * [tex]T^2[/tex].

We can calculate the velocity at the end of the slope as follows;

Vx = v * cos θVx = sqrt(2gh) * cos θ

Vx = sqrt(2*9.8*50) * cos(10)

Vx= 233.51 m/s.

Now, using the horizontal velocity, we can calculate the time required to reach the ground.

We know that;

distance = velocity * time + 0.5 * acceleration * time^2distance

= Vx * T

(as the acceleration in the horizontal direction is zero).

Solving for T;

T = distance / VxT = 50 m / 233.51 m/s

T = 0.214 s

Now, we can use the vertical equation to calculate the displacement (or distance travelled) in the vertical direction.

We know that; ay = g = 9.8 m/s^2Vyf = Vi + ay *t

We need to find the final velocity. Vyf at the end of the slope. Initially, we know that; Vi = 0So,

solving for Vyf;

Vyf = ay * tVyf = 9.8 m/s^2 * 0.214 sVyf = 2.10 m/s

Using this final velocity, we can calculate the displacement (distance travelled) as follows;

y = Vi * t + 0.5 * ay * t^2y = 0 + 0.5 * 9.8 m/s^2 * (0.214 s)^2y = 0.22 m.

Now, the horizontal displacement can be calculated as follows;

x = Vx * T (distance covered in the horizontal direction)

x = 233.51 m/s * 0.214 s

x = 50.02 m.

For more details about frictionless click here:

https://brainly.com/question/26515803#

#SPJ11

Answer:

Explanation:

B

Two waves travel at the same speed. The frequency of wave A is 1000 Hz, and the frequency of wave B is 4000 Hz. Wavelength A is 0.25 meters.

Wavelength, frequency, and speed are interrelated in a mathematical relationship known as the wave equation:

v = fλ

Where: v = velocity of the wave

f = frequency

λ = wavelength

The velocity of a wave is equivalent to the product of its wavelength and frequency. In addition, since the two waves in this situation are traveling at the same speed, their wavelengths are inversely related to their frequencies. As a result, the formula for wavelength is:

wavelength = velocity/frequency

Substituting the given values in the equation,

wavelength A = velocity/frequency A

wavelength A = 300/1000

wavelength A = 0.3 meters

The frequency of wave A is 1000 Hz, and the frequency of wave B is 4000 Hz. Wavelength A is 0.3 meters.

For more question on speed click on

https://brainly.com/question/27888149

#SPJ11

Answer:

it is 17 dollars .

Explanation:

I had a test like this and I remember the qeustions

A 9.0-V battery costs $3.00 and will deliver 0.0250 A for 26.0 h before it must be replaced. then the cost per kWh is $512.82.

Energy is nothing but the ability to do work. there are different energies in different form which are thermal energy, mechanical energy, electric energy and sound energy etc. According to first law of thermodynamic, Energy neither be created nor be destroyed. it can only be transferred from one form into another form. Energy is expressed in joule (J). its dimensions are [M¹ L² T⁻²].

The energy delivered by the battery can be calculated using the formula:

energy = power x time

where power is the product of voltage and current, and time is given in hours.

The power delivered by the battery is:

power = voltage x current = 9.0 V x 0.0250 A = 0.225 W

The time for which the battery will deliver this power is 26.0 hours.

So, the energy delivered by the battery is:

energy = power x time = 0.225 W x 26.0 h = 5.85 Wh

To convert Wh to kWh, we divide by 1000:

energy = 5.85 Wh ÷ 1000 = 0.00585 kWh

The cost per kWh can be calculated by dividing the cost of the battery by the energy delivered, and then multiplying by 1000 to convert to dollars per kWh:

cost per kWh = (3.00 dollars / 0.00585 kWh) x 1000 = 512.82 dollars/kWh (rounded to two decimal places)

Therefore, the cost per kWh for this battery is $512.82.

To know more about Power :

https://brainly.com/question/29575208

#SPJ2.