Answer:
Resistance / Edge 2022
Explanation:
This is late, but just in case someone needs the answer. Hope this helps!
(*^▽^*)
Tungsten metal is used exclusively for making the filament of electric bulbs because it has a very high melting point
What is a tungsten bulb?Tungsten metal is used exclusively for making the filament of electric bulbs because it has a very high melting point. Due to its high melting point, the tungsten filament can be kept white-hot without melting away
Tungsten wire is used as the filament in light bulbs. It glows white-hot as current passes through it.
Tungsten is used in light bulbs because its high resistivity converts electric energy into light and heat.
To know more about Tungsten bulbs follow
https://brainly.com/question/1738190
True or False : If a car drives on a road for a nonzero amount of time, then its average velocity must be nonzero.
Answer:
Your answer would be:
B.) False
If a car drives on a road for a nonzero amount of time, then its average velocity must be nonzero.
If a car drives for a nonzero amount of time, then its average acceleration must be nonzero.
Explanation:
Have a great rest of your day
#TheWizzer
Reducing access to waterways will lead to an increase in human impact on waterways. please select the best answer from the choices provided t f
Answer:
F
Explanation:
Reducing access will cause less damage to occur
Answer: the answer is false
Angie, brad, and carlos are discussing a physics problem in which two identical bullets are fired with equal speeds at equal-mass wood and steel blocks resting on a frictionless table. One bullet bounces off the steel block while the second becomes embedded in the wood block. All the masses and speeds are the same, says angie, so i think the blocks will have equal speeds after the collisions. But what about momentum? asks brad. The bullet hitting the wood block transfers all its momentum and energy to the block, so the wood block should end up going faster than the steel block. I think the bounce is an important factor, replies carlos. The steel block will be faster because the bullet bounces off it and goes back the other direction.
Answer:
Momentum must be conserved in the collision.
The steel block must move faster after the collision to preserve momentum.
If the steel block is moving faster it will aso have more kinetic energy.
(Note; If the bullet hits the steel block it will have some momentum in the reverse direction and thus have a greater change in total momtntum than the bullet that becomes imbedded in the wood block)
If you pull a permanent magnet rapidly away from a tank circuit, what is likely to happen in that circuit?.
Answer:
attract the magnetic ratio engine light of rock level
A 160 kg cart has a momentum of 870 kg m/s. What is the velocity of the cart?
Answer: 5.44 m/s
Explanation:
Given:
Mass of cart: 160 kg
Momentum of cart: 870 kg•m/s
[tex]$$Momentum $|\rho|=m \times v$$$\begin{aligned}&870 \ kg\cdot m/s=160 \mathrm{~kg} \times v \\&v=5.44 \mathrm{~m} / \mathrm{s}\end{aligned}$$[/tex]
Answer:
The momentum is defined as :
P=mv
Where m is the mass and v is the velocity. In this case we know the mass is 160 kg and the momentum is 870 kg plugging in this equation above and solving for the velocity we have
870=160V
V=870÷160
V=5.44
Therefore, the velocity of the cart is 5.44 m/s.
Which statement is true about the reaction shown by this chemical equation?
HCI + NaOH – NaCl + H20
O A. It is exothermic.
O B. It is a synthesis reaction.
O C. It is endothermic.
D. It is a combustion reaction.
SUBMIT
The given reaction, HCl + NaOH --- NaCl + H₂O is an example of an exothermic reaction. Hence, option A is correct.
What is an exothermic reaction?In a reaction, the energy released in the form of heat is called an exothermic reaction. In an exothermic reaction, the heat energy is transferred to the surroundings. The chemical equation is Reactant = Product + Energy.
The energy absorbed from the surroundings is called an endothermic reaction. The heat energy taken from the reactants to form a product is called an endothermic reaction. It is described by the chemical equation as Reactant + Energy = Product.
From the given reaction,
HCl + NaOH --- NaCl + H₂O
HCl and NaOH is reactant and NaCl and water is a product. When strong acid (HCl) is mixed with a strong base (NaOH), it gives sodium chloride(NaCl) and water along with heat energy.
When the product is formed from the reactant, heat energy is released. This reaction is also called a Neutralisation reaction. The neutralization reaction are exothermic reaction, that forms chemical bonds by the release of energy.
When water is formed as a product by the release of greater energy than the energy absorbed is called a Neutralization/ exothermic reaction. Hence, the correct option is A) It is exothermic.
To learn more about Exothermic and endothermic reactions:
https://brainly.com/question/27570614
#SPJ5
Which of the following is true about the Sun?
A.
The Sun is the only star in the Solar System.
B.
The Sun is the only star in the Milky Way.
C.
The Sun is not a star.
D.
The Sun is the only star in the universe.
Which layer of the sun is where plasma rises and sinks due to temperature differences?.
Answer:
Just beneath the photosphere, and extending inward to about 0.7 Rsun, is the convection zone. Energy generated in the core of the Sun moves outward through this layer by a boiling motion in which hot plasma rises, releases some of its energy, cools, and then sinks again.
Explanation:
what would happen in a capacitor if the dielectric was not made out of an insulator
[tex]
\mathbb \blue{Answer }[/tex]
[tex]Introducing \: \: a \: dielectric \: \: into \: \\ a \: \: capacitor \: \: decreases \: \: \\ the \: \: electric \: \: field, \: \: \\ which \: \: decreases \: \: the \: \: \\ voltage, \: \: \ which \: \: increases \: \: the \: \: \\ capacitance. \: \: A \: capacitor \: \: with \: a \: \\ dielectric \: \: stores \: the \: \\ same \: \: \ charge \: \: as \: one \: \\ without \: \: a \: dielectric, \: but \: at \: \\ a \: \: lower \: \: voltage. \: \: \\ Therefore \: \: a \: \: capacitor \: \: with \: \: a \: \\ dielectric \: \: in \: \: it \: \\ is \: \: more \: \: effective \: [/tex]
[tex]\mathbb \blue{ I \: hope \: it's \: helpful \: \: for \: you }[/tex]
,,,,,,,,,,,,,,,,,,,,,,,,,
Why do planets like Jupiter and Saturn have large gas atmospheres while Mercury and Mars do not?
options:
Because Jupiter and Saturn have more mass
Because of each planets distance from the Sun
Because of their different orbits around the Sun
Because they were formed at different times
The solar system shows the planets in their orbits around the sun in this order: Mercury, Venus, Earth with Moon, Mars, Jupiter, Saturn. Fixed stars are around the outside of the orbit of Saturn.
Explanation:
Aristarchus of Samos was an ancient Greek astronomer and mathematician who presented the first known heliocentric model that placed the Sun at the center. So I had to choose the choice that was most similar to that.
If new evidence is discovered that a theory does not accommodateoptions:
the theory is disproved and thrown out
the theory then becomes a law
the theory is generally modified in light of this new evidence
the theory can not change so it stays the same
Answer:
The theory is generally modified in light of this new evidence.
Which of the following processes is more easily observable for light with a short wavelength?
help please.
Answer:
Option B
Explanation:
Option B
Answer is PHOTOELECTRIC EFFECT
You throw a 0.5 kg ball with a force of 10 N. What is the acceleration of the ball?
Answer:
20m/s^2
Explanation:
F=ma, therefore 10N = 0.5kg * a. Solve for a.
How does water form in the clouds? Explain how
When air rises in the atmosphere it gets cooler and is under less pressure. When air cools, it's not able to hold all of the water vapor it once was. Air also can't hold as much water when air pressure drops. The vapor becomes small water droplets or ice crystals and a cloud is formed.
I hope this helps you..
Mike is pushing a car up a ramp. What could Mike do to reduce the effort force he needs to use to push the car?
Answer:
He could use a really big pulley system or get in it and drive or call a tow truck.
Question 5 of 10
Why does a patient receive more radiation from a CT scan than from having an X-ray image made?
A. A CT scan involves multiple X-ray images.
B. Higher-frequency rays are used in a CT scan.
C. Fewer X-rays are reflected in a CT scan.
D. The X-rays are more powerful in a CT scan.
Answer: A CT scan involves multiple X-ray images.
Answer: A CT scan involves multiple X-Ray images
Explanation:
I did it and it was correct
Question 20 I need help ASAP!!
Answer:
1.) Gas = Are the particles moving quickly in a radom pattern?
2.) Plasma = Are the particles electrically charged?
3.) Solid = Are the particles vibrating in a fixed position?
4.) Liquid = Are the particles sliding past each other?
Hope this helps!
How is "one second time" defined in SI system?
Answer:
Since 1997: A second is a time equal to 9,192,631,770 periods of radiation corresponding to the transition between two hyperfine levels of the ground state of the cesium-133 atom.
This definition refers to a caesium atom at rest at a temperature of 0 K
Explanation:
Light of wavelength 630 nm (630 x 10-9 m) is used to produce a double slit diffraction pattern where the third order image is 0.10 m from the central image using a diffraction grating constant of 4.9 x 10-5 m. How far is the screen from the slits? SHOW ALL WORK
For Light of wavelength 630 nm (630 x 10-9 m) is used to produce a double slit diffraction pattern where the third order image is 0.10 m the distance of the screen from the slits is mathematically given as
D = 26m
How far is the screen from the slits?
Generally, the equation for the small-angle approximation is mathematically given as
x = n(Landa)D/d
therefore,
D = 0.10x4.9 x 10-5/(3x630 x 10-9)
D = 26m
In conclusion, the distance of the screen from the slits is
D = 26m
Read more about Lens
https://brainly.com/question/13644773
Starting from rest, an object accelerates on a straight level surface at the rate of 2 m/s for 10 s. 9. What is the speed of the object at the end of 10 s? (A)5 m/s (B) 10 m/s (C) 20 m/s (D) 30 m/s (E) 40 m/s
Answer:
C
Explanation:
a = v-u / t
a×t = v (u= 0 therefore is ignored)
2m/s² × 10s = v
v= 20m/s
Write your own real-world scenario where the Pythagorean Theorem can be applied to find a missing piece. You may choose to write a problem that is two- or three-dimensional in nature. Be sure that you will be able to draw a diagram of your scenario.
Write out your problem and submit it for Part 1. Be sure to end your scenario with a question
Answer:
hey
Explanation:
Displacement covered by the man calculated by using Pythagoras theorem is 10 km.
What is Pythagoras Theorem ?Pythagoras theorem states that, for a right-angled triangle, the square of the hypotenuse side is equal to the sum of squares of the altitude and base sides.
Here,
The Pythagoras Theorem can be written as,
c² = b² + a²
where c is the hypotenuse, b is the base and a is the altitude of the triangle.
An example of application of the Pythagoras theorem is,
A man started walking from his home and covered a distance of 8 km towards the east and then turned right and walked a distance of 6 km towards the south, what is his displacement now from his starting point ?
A line drawn from his current position and his initial point represents the displacement covered by the man.
Let the starting point be A, then he walks to the point B and then he turns right and walks upto the point C.
Drawing a figure including all the data, we get a right angled triangle, ABC. So,
The base of the triangle, BC = 6 km
Altitude of the triangle, AB = 8 km
The displacement of the man = hypotenuse of the triangle
d = AC
According to Pythagoras Theorem,
AC² = BC² + AB²
AC² = 6² + 8² = 100
AC = √100
Therefore, displacement, d = AC = 10 km.
Hence,
Displacement covered by the man calculated by using Pythagoras theorem is 10 km.
To learn more about Pythagoras theorem, click:
https://brainly.com/question/343682
#SPJ7
Attaching the image file here.
A pebble of mass 50g is moving with a velocity of 20m/s.What is its kinetic energy?
[tex] \bf\sf \underline{Given: - }[/tex]
[tex] \text{Mass of pebble= 50g}[/tex][tex] \text{Velocity of pebble= 20m/s}[/tex][tex] \bf\sf \underline{To \: Find: - }[/tex]
[tex] \text{Kinetic Energy of Pebble}[/tex][tex] \bf\sf \underline{Solution: - }[/tex]
We know that, to find the Kinetic energy we are required mass and velocity and Here Both parameters are provided But mass is in gram so we need change it into kg,
1g = 0.001kg,
⠀⠀⠀50g = 0.05g
Now we know the formula of Kinetic energy,
[tex] \sf \boxed{ \star\bf{\: Kinetic \: energy = \frac{1}{2} m {v}^{2}}} \\ \\ \qquad \qquad = \frac{1}{ \cancel2} \times 0.05 \times \cancel{20}\times 20 \\ \\ \qquad \qquad =0.05 \times 200 \\ \\ \qquad \qquad \sf = 10J \: [/tex]
Hence, the kinetic energy of the pebble is 10J.
is it possible to put negative and positive charge at same time at electroscope leaves?
Answer:
No
Explanation:
If a positively charged object is brought near a negatively charged electroscope, it will attract some of the excess electrons up the stem and out of the leaves, causing the leaves to come slightly together
A sound wave, generated at a frequency of 440 hertz has a wavelength of 2.3 meters as it travels through a solid material. The approximate speed of the wave is ____ m/sec.
The approximate speed of the sound wave traveling through the solid material is 1012m/s.
Wavelength, Frequency and SpeedWavelength is simply the distance over which the shapes of waves are repeated. It is the spatial period of a periodic wave.
From the wavelength, frequency and speed relation,
λ = v ÷ f
Where λ is wavelength, v is velocity/speed and f is frequency.
Given the data in the question;
Frequency of sound wave f = 440Hz = 440s⁻¹Wavelength of the wave λ = 2.3mSpeed of the wave v = ?To determine the approximate speed of the wave, we substitute our given values into the expression above.
λ = v ÷ f
2.3m = v ÷ 440s⁻¹
v = 2.3m × 440s⁻¹
v = 1012ms⁻¹
v = 1012m/s
Therefore, the approximate speed of the sound wave traveling through the solid material is 1012m/s.
Learn more about Speed, Frequency and Wavelength here: brainly.com/question/27120701
In a circuit, when the electrical resistance increases, the current _______ because it is _______ for the electrons to flow
In a circuit, when the electrical resistance increases, the current _______ because it is _______ for the electrons to flow.
[tex] \\ [/tex]
Answer:In a circuit, when the electrical resistance increases, the current decreases because it is blocking for the electrons to flow.
#LearnWithBrainly
Which of the four numbered galaxies have ongoing star formation?.
The image here is not found here but star formation is characterized by clouds of dust where stars are born.
What is star formation?Star formation is a physical phenomenon where molecular clouds in space need to collapse to generate stars.
Stellar evolution is a process that initiates when a star is formed and ends when it dies (formation of a red giant).
Stars can be generated inside clouds of dust which are dispersed in different types of galaxies in the universe.
Learn more about star formation here:
https://brainly.com/question/7467199
. A marble sphere with a diameter of 1/4 inch is fully immersed in the oil of density 0.961 g/cm3 . Calculate the buoyant force exerted on the marble sphere by the oil.
Answer:
See below ( was it REALLY 1/4 INCH??)
Explanation:
Calculate the volume of the sphere
v = 4/3 pi r^3
this times the density of the oil will give g displacement
then f = ma
4/3 pi (.25 in * 2.54 cm/inch) ^3 * .961 = 1.0307 gm
1.0307 gm is .0010307 kg
f = ma = .0010307 * 9.8 = .0101 N
An object with a mass of 2.0 kg accelerates 8.3 m/s? when an unknown force is applied
to it. What is the amount of the force?
Answer:
16.6 NExplanation:
We know the relation :
Force = Mass x AccelerationWe are given that :
Mass = 2.0 kgAcceleration = 8.3 m/s²Hence, on substituting the values in the equation :
F = 2.0 x 8.3F = 16.6 NThe given information is,
→ Mass = 2 kg
→ Acceleration= 8.3 m/s
→ Force = F (in Newton)
Now we have to find the,
→ Amount of force applied to the object.
Formula we use,
→ F = Mass × Acceleration
Then the amount of force will be,
→ F = Mass × Acceleration
→ F = 2 × 8.3
→ [ F = 16.6 N ]
Hence, the amount of force is 16.6 N.
explain how to identify the points under compression and tension
Answer:
Pls make me brainliest
Explanation:
the compression force is the force generated from compressing an object or substance. When shearing forces are aligned into each other, they are called compression forces.
The compression force is used to power everything from compression brakes to hand tools. The compressive strength of materials and structures is an important engineering consideration.
The compression force can be visualized by placing an object on a spring. When the spring is compressed and then released, the object is ejected into the air.
This is a result of the compression force that is generated from compressing the spring.
This system has a constant velocity, and there is an equilibrium because the tension in the cable, which is pulling up the object, is equal to the weight force, i.e., mg. Where M is a mass, and g is the acceleration caused by gravity, which is pulling down the object.
The Formula of Tension.
T = Mg
Tension word becomes from a Latin word meaning “to stretch.” Testing part of the force, Like one type of pull force. All physical objects that are in contact may exert forces on each other.
This contact forces different names based on these types of objects in contact. Where one of the objects exerting the force happens to be a rope, string, chain, or cable we call the force tensions
An electric appliance is connected by wires to a 240-volt source of voltage. If the combined resistance of the appliance and wires is 12 ohms, how much current is flowing through the circuit?
Apply ohms law
V=IR240=12II=240/12I=20AAnswer :-
Current is 20 Ampere .Explanation :-
As per the provided information in the given question, we have been given that the Potential Difference is 240 Volt's . Resistance is given as 12 Ohm's . And, we have been asked to calculate the Current .
For calculating the Current , we will use the Formula :-
[tex] \bigstar \: \: \: \boxed{ \sf{ \: Current \: = \: \dfrac{Voltage}{Resistance} \: }} \\ [/tex]
Therefore , by Substituting the given values in the above Formula :-
[tex] \Longrightarrow \: \: \: \sf { Current \: = \: \dfrac{Voltage}{Resistance} } \\ [/tex]
[tex] \Longrightarrow \: \: \: \sf { Current \: = \: \dfrac{ \: 240 \: }{12} } \\ [/tex]
[tex] \Longrightarrow \: \: \textbf {\textsf { Current \: = \: 20 }} \\ [/tex]
Hence :-
Current = 20 Ampere .[tex] \underline {\rule {180pt}{4pt}} [/tex]
Additional Information :-
[tex] \Longrightarrow \: \: \: \sf {Voltage \: = \: Current \: \times \: Resistance} [/tex]
[tex] \Longrightarrow \: \: \: \sf {Current \: = \: \dfrac {Voltage}{Resistance} } [/tex]
[tex] \Longrightarrow \: \: \: \sf {Resistance \: = \: \dfrac {Voltage}{Current} } [/tex]