Vector A points in the negative z direction. Vector points at an angle of 31.0" above the positive z axis. Vector C has a magnitude of 16 m and points in a direction 42.0* below the positive x axis.
Vector A, A = {0, 0, -a}
Vector C, C = {16 cos 42.0°, 0, - 16 sin 42.0°}
Let B = A + B + C. Hence, B = {0, 0, -a} + {B sin 31.0° cos θ, B sin 31.0° sin θ, B cos 31.0°} + {16 cos 42.0°, 0, - 16 sin 42.0°}
Then, equating the x, y, and z components of the above equation separately, we get:
B sin 31.0° cos θ = - 16 cos 42.0°B sin 31.0° sin θ = 0
B cos 31.0° = a - 16 sin 42.0°
From the second equation, we have B = 0 or sin θ = 0, we have B = 0. But, B = 0 doesn't satisfy the third equation. Hence, sin θ = 0. So, θ = 0° or θ = 180°.When θ = 0°, we get,
B sin 31.0° cos θ = - 16 cos 42.0°B sin 31.0° (1) = - 16 cos 42.0°
B = - 16 cos 42.0° / sin 31.0°
Then, |B| = 22 m (approx.)
So, the required value of |B| is 22 m (approx.)
Note: You can also solve it by using the dot product of the vectors.
Learn more about vectors: https://brainly.com/question/17177764
#SPJ11
Looking up into the sky from Mercury's surface, during one
day-night cycle how many sunrises happen?
Mercury, the smallest planet in our solar system, experiences a slow day-night cycle, with one sunrise and one sunset during its 176 Earth-day cycle. Its surface temperature varies significantly, ranging from -173°C (-280°F) at night to 427°C (800°F) during the day, due to its thin atmosphere's inability to retain or distribute heat.
Mercury is a planet that is closest to the sun and is also the smallest planet in the solar system. A day-night cycle on Mercury takes approximately 176 Earth days to complete, while a year on Mercury is around 88 Earth days long. So, if one was to look up into the sky from Mercury's surface, during one day-night cycle there would be only one sunrise and one sunset.
Similar to Earth, the side of Mercury facing the sun experiences daylight and the other side facing away from the sun experiences darkness. Since Mercury has a very slow rotation, it takes a long time for the sun to move across its sky. This makes the sun appear to move very slowly across Mercury's sky, and it takes around 59 Earth days for the sun to complete one full journey across the sky of Mercury.
Due to the fact that Mercury's axial tilt is nearly zero, there are no seasons on this planet. Mercury's surface temperature varies greatly, ranging from -173°C (-280°F) at night to 427°C (800°F) during the day. This is mainly due to the fact that Mercury has a very thin atmosphere that can neither retain nor distribute heat.
Learn more about Mercury
https://brainly.com/question/30914360
#SPJ11
Electric room heaters use a concave mirror to reflect infrared (IR) iradiation from hot coils. Note that IR follows the siume law of reflection as visible light.
Find the magnification of the heater element, given that the mirror has a radius of curvature of 48 cm and produces an image of the coils 3.2 m away from the mirror.
M = ______________
the magnification of the heater element is 0.5.
radius of curvature (r) of the mirror = 48 cm
Image distance (v) = 3.2 m
Focal length (f) = r/2 = 48/2 = 24 cm
According to mirror formula:1/v + 1/u = 1/f
Where,
u is object distance.
In this case, u = -f [since the object is placed at the focus]
1/v = 1/f - 1/u=> 1/v = 1/24 + 1/24=> 1/v = 1/12=> v = 12 m
Magnification (M) is given as:
Magnification M = -v/u=> M = -12/-24= 0.5
So, the magnification of the heater element is 0.5.
Learn more about magnification:
https://brainly.com/question/131206
#SPJ11
A plastic rod of length 1.54 meters contains a charge of 1.9nC. The rod is formed into semicircle. What is the magnitude of the electric field at the center of the semicircle? Express your answer in N/C A silicon rod of length 2.30 meters contains a charge of 5.8nC. The rod is formed into a quartercircle What is the magnitude of the electric field at tho center? Express your answer in N/C
the electric field at the center of the quarter circle is E = 2.29 × 107 N/C.Therefore, the magnitude of the electric field at the center of the semicircle is 1.12 × 107 N/C, and the magnitude of the electric field at the center of the quarter circle is 2.29 × 107 N/C.
The electric field at the center of a semicircle or quarter circle can be determined by considering the contributions from each segment of the rod. Each segment can be treated as a point charge, and the electric field at the center can be obtained by summing the contributions from all segments.
For the semicircle formed by the plastic rod, the electric field at the center can be calculated using the formula:E = k * (Q / r²),where E is the electric field, k is the Coulomb's constant, Q is the charge on the rod, and r is the radius of the semicircle (which is equal to half the length of the rod).
Similarly, for the quarter circle formed by the silicon rod, the electric field at the center can be calculated using the same formula, taking into account the appropriate length and charge.By plugging in the given values into the formula, the magnitudes of the electric fields at the centers of the semicircle and quarter circle can be determined.
Learn more about electric field here:
https://brainly.com/question/11482745
#SPJ11
A band pass filter with centre frequency 12 KHz. R=10022; C=2μF 1- calulate the value of L by mH V. L с - ние R V₂
the value of the inductance (L) required for the bandpass filter with a center frequency of 12 kHz, a resistor (R) value of 10 kΩ, and a capacitor (C) value of 2 μF is approximately 1.38 mH.
To calculate the value of the inductance (L) in millihenries (mH) for a bandpass filter with a center frequency of 12 kHz, a resistor (R) value of 10 kΩ, and a capacitor (C) value of 2 μF, we can use the following formula:
L = 1 / (4π² * f² * C)
where f is the center frequency in Hz and C is the capacitance in farads.
In a bandpass filter, the center frequency (f) is the frequency at which the filter has its maximum response. To calculate the value of the inductance (L), we use the formula mentioned above, which is derived from the resonance frequency formula for an RLC circuit.
In this case, the center frequency is given as 12 kHz, so we substitute f = 12,000 Hz into the formula. The capacitance (C) is given as 2 μF, which needs to be converted to farads by dividing by 1,000,000 (1 μF = 1/1,000,000 F).
Substituting the values into the formula:
L = 1 / (4π² * (12,000 Hz)² * 2 μF)
Simplifying:
L = 1 / (4π² * 144,000,000 Hz² * 2 μF)
L = 1 / (1,811,557,368,000 Hz² * 2 μF)
L ≈ 1.38 mH
Therefore, the value of the inductance (L) required for the bandpass filter with a center frequency of 12 kHz, a resistor (R) value of 10 kΩ, and a capacitor (C) value of 2 μF is approximately 1.38 mH.
To know more about Band-pass filter click here:
https://brainly.com/question/32825178
#SPJ11
The drag force of a projectile in air is proportional to the square of the velocity: D=bv² Which of the following options correctly represents the dimensions of the constant b? a. m² = kg/s² b. kg/m c. m³kg d. Ns/m² e. kg/s²
The dimensions of the constant b is Ns/m². The correct option is d
The drag force of a projectile in air is proportional to the square of the velocity.
This means that D= bv²
where
D is the drag force,
v is the velocity,
b is a constant.
Therefore, the dimensions of the constant b can be obtained as follows:
Dimension of force F = MLT−2
Dimension of velocity v = LT−1
Dimension of drag coefficient b = D/F = [MLT−2]/[L2T−2] = [M/T] [1/L]2
The above is the dimensional formula for b.
To make this dimensionless constant into SI units we need to do some conversions to get the right combination of dimensions that give the correct unit.
Now, mass is in kilograms (kg), length is in meters (m), and time is in seconds (s).
Therefore, we have,
Dimension of b = [M/T] [1/L]2
= kg/s . 1/m2
= Ns/m²
Hence, the correct option is d. Ns/m².
Learn more about the dimension:
brainly.com/question/30338180
#SPJ11
quickly please exam!!
Define the following: 1. Law of corresponding states. (2 marks) 2. Under what conditions the real gas may behave as an ideal gas. (2 marks) 3. Please explain qualitatively, the difference between the
1. The law of corresponding states that at the same reduced conditions (expressed in terms of reduced temperature and pressure), different gases will exhibit similar behavior in terms of their compressibility factor (Z). This law allows gases to be compared and studied based on their reduced properties rather than their individual molecular characteristics.
2. Real gases may behave as ideal gases under conditions of low pressure and high temperature. When the pressure is low and the intermolecular forces between gas molecules are weak, the gas molecules are far apart and their volume becomes negligible. Additionally, at high temperatures, the kinetic energy of the gas molecules is significant, leading to increased randomness and less interaction between the molecules.
1. The law of corresponding states establishes a relationship between the behavior of different gases by comparing their reduced properties. The reduced temperature (Tr) is the actual temperature divided by the critical temperature (Tc), and the reduced pressure (Pr) is the actual pressure divided by the critical pressure (Pc). By plotting Z, the compressibility factor, against Pr and Tr, gases of different compositions can be compared on a single graph. The law states that gases with similar values of Z at the same reduced conditions will exhibit similar behavior, indicating a deviation from ideal gas behavior.
2. Real gases deviate from ideal gas behavior due to intermolecular forces and the finite volume of gas molecules. However, under certain conditions, these deviations become negligible, and the gas behaves as an ideal gas. When the pressure is low, the gas molecules are far apart, and their volume is relatively small compared to the available space. This reduces the impact of intermolecular forces and makes the gas behave similarly to an ideal gas. Similarly, at high temperatures, the kinetic energy of gas molecules overcomes the attractive forces between them, resulting in less interaction and a closer approximation to ideal gas behavior.
3. a. In the saturation envelope of a mixture of methane (10%) and ethane (90%), the envelope represents the range of conditions (temperature and pressure) at which the mixture exists as a vapor and liquid in equilibrium. Due to the difference in molecular properties, the saturation envelope for this mixture will be different from that of pure methane or ethane. The composition of the mixture influences the temperature and pressure ranges at which the transition from vapor to liquid occurs.
b. In the saturation envelope of a mixture of ethane (50%) and pentane (50%), the composition of the mixture plays a significant role. The saturation envelope for this mixture will exhibit a different temperature and pressure range compared to the individual components. The presence of different molecules alters the intermolecular interactions and leads to changes in the phase transition behavior.
4. The five main processes during the processing of natural gas are:
a. Exploration and Production: This involves locating and extracting natural gas reserves from the earth.
b. Gathering and Transportation: Natural gas is collected from multiple wells and transported via pipelines or liquefied natural gas (LNG) carriers to processing plants or distribution points.
c. Processing and Treatment: Natural gas goes through various processes to remove impurities, such as water, sulfur compounds, and other contaminants.
d. Storage: Natural gas may be stored in underground facilities or LNG tanks for later use or transportation.
e. Distribution and Utilization: Natural gas is distributed through pipelines to residential, commercial, and industrial consumers for various applications such as heating, cooking, and electricity generation.
To know more about the law of the corresponding click here:
https://brainly.com/question/28194050
#SPJ11
Define the following: 1. Law of corresponding states. (2 marks) 2. Under what conditions the real gas may behave as an ideal gas. (2 marks) 3. Please explain qualitatively, the difference between the saturation envelope of the following mixtures: (4 marks) a. Methane and ethane, where methane is 10% and ethane is 90%. b. Ethane and pentane, where ethane is 50% and pentane is 50%. 4. List down the five main processes during the processing of natural gas. (2 marks)
A football of mass 1 kg is thrown at an initial velocity of 7 m/s at an angle of 33 degrees with respect to the horizontal. Please determine the maximum height the football can reach
The football can achieve a maximum height of 0.7415 m when thrown with a velocity of 7 m/s at an angle of 33 degrees with respect to the horizontal axis.
Let's find the initial velocity of the football on the vertical axis,
the velocity of football in the vertical axis, u = 7 sin(33)
u =7 (0.5446)
u = 3.8124
Now let's find the maximum height that can be achieved by the football.
The maximum velocity of the football will be zero, so the final velocity is zero.
Using equation,
[tex]v^2-u^2 = 2ah[/tex]
we can find the height where h is the maximum height that can be achieved.
Substituting all the values in the above equation, we get
0 - 14.5343 = - 2(9.8)h
This negative depicts that acceleration is in the opposite direction of the initial velocity.
14.5343 = 19.6 h
h = 0.7415
Hence, the football can achieve a maximum height of 0.7415 m when thrown with a velocity of 7 m/s at an angle of 33 degrees with respect to the horizontal axis.
To learn more about maximum height :
https://brainly.com/question/11182480
1. Write down an explanation, based on a scientific theory, of why lightning travels through the air. Explain why it is scientific. Then write down a non-scientific explanation of the same phenomenon, and explain why it is non-scientific. Then write down a pseudoscientific explanation of the same phenomenon, and explain why it is pseudoscientific.
2. Write a question appropriate about the action potential of the human nervous system and a current source of 18.18 amperes. Then answer it.
1. Scientific explanation of why lightning travels through the air:A scientific explanation of lightning is that lightning is an electrical discharge caused by a buildup of electrical charges in the atmosphere. When a thunderstorm forms, it can create a charge separation in the atmosphere.
The negatively charged electrons collect at the bottom of the cloud, and the positively charged particles move to the top of the cloud. The charge separation causes an electric field to form between the cloud and the ground. When the electric field becomes strong enough, it ionizes the air molecules between the cloud and the ground, creating a path for the electrons to travel through.
This path of ionized air molecules is called a stepped leader, which travels down towards the ground, and when it reaches close to the ground, a return stroke occurs, which creates the bright flash of lightning seen.Non-scientific explanation of why lightning travels through the air:
Gods are angry and they have sent lightning as a punishment for people's sins.Pseudoscientific explanation of why lightning travels through the air:One pseudoscientific explanation of lightning is that it is caused by the alignment of the planets or the movement of the stars.
This is pseudoscientific because there is no scientific evidence to support this idea, and it is based on superstition rather than science.
2. Question appropriate about the action potential of the human nervous system and a current source of 18.18 amperes:
A current source of 18.18 amperes can cause severe damage to the human nervous system, including nerve damage, tissue damage, and even death. The normal range of currents for the human nervous system is around 10-20 microamperes, so a current of 18.18 amperes is over a million times greater than the normal range.
This level of current can cause the nerves to become depolarized, which can lead to the loss of nerve function and severe tissue damage.
Learn more about electric field here,
https://brainly.com/question/19878202
#SPJ11
The only force acting on a 2.3 kg body as it moves along the positive x axis has an x component Fx = −4×N, where x is in meters. The velocity of the body at x=1.4 m is 9.1 m/s. (a) What is the velocity of the body at x=4.6 m ? (b) At what positive value of x will the body have a velocity of 5.5 m/s ? (a) Number ________________ Units _________________
(b) Number ________________ Units _________________
(a)
The velocity of the body at x = 4.6 m is -2.69 m/s.
Number: -2.69
Units: m/s
(b)
The positive value of x where the body will have a velocity of 5.5 m/s is 9.6 m.
Number: 9.6
Units: m
Mass of the body, m = 2.3 kg
Force acting on the body, Fx = −4 N
Initial velocity of the body, u = 0 m/s
Velocity of the body at x = 1.4 m, v = 9.1 m/s
Let's find the acceleration of the body at x = 1.4 ma
= F/m
= (-4 N)/2.3 kg
= -1.74 m/s²
(a)
Now, let's find the velocity of the body at x = 4.6 m
Final position of the body, x = 4.6 m
Initial position of the body, x = 1.4 m
Distance covered by the body, s = x - u = 4.6 - 1.4 = 3.2 m
Using the second equation of motion,
v² = u² + 2as
v² = 0 + 2 × (-1.74) × 3.2
v = -2.69 m/s
The velocity of the body at x = 4.6 m is -2.69 m/s.
Number: -2.69
Units: m/s
(b)
Now, let's find the positive value of x where the body will have a velocity of 5.5 m/s.
Final velocity of the body, v = 5.5 m/s
Initial velocity of the body, u = 0 m/s
Let the distance covered by the body be s meters.
Using the third equation of motion,v² = u² + 2as
5.5² = 0 + 2a × s
We know, a = -1.74 m/s²
5.5² = 2 × (-1.74) × s
s = 8.2 m
Therefore, the positive value of x where the body will have a velocity of 5.5 m/s is 1.4 + 8.2 = 9.6 m.
Number: 9.6
Units: m
Learn more about the equation of motion:
brainly.com/question/24018491
#SPJ11
1- The motion of a star caused by an orbiting planet is called a "wobble."
Why does the star wobble when it has an orbiting planet?
2- Based on your observations, what is the relationship between the movement of the star and the mass of the planet?
3- What happens to the wobble motion of the star when the planet has a very low mass?
a) the star continues to wobble
b) the star stops wobbling
4- Explain your answer
5- How certain are you about your claim based on your explanation? Select an option
(1) Not at all certain, (2), (3), (4), (5) Very Certain
6- Explain what influenced your certainty rating.
1. The motion of a star caused by an orbiting planet is called a "wobble" because of the gravitational pull of the planet on the star. This gravitational pull causes the star to move back and forth as the planet orbits around it. This motion can be detected by observing the light emitted by the star. The wavelength of the light will change as the star moves towards or away from the observer. This is known as the Doppler effect.
2. The movement of the star is directly related to the mass of the
planet
. The more massive the planet, the stronger the gravitational pull, and the greater the wobble of the star. The opposite is also true; the less massive the planet, the weaker the gravitational pull, and the smaller the wobble of the star.
3. When the planet has a very low mass, the wobble motion of the
star
continues, albeit with a much smaller amplitude. Therefore, the answer is (a) the star continues to wobble.
4. The wobbling motion of the star is caused by the
gravitational pull
of the planet. The larger the planet, the stronger the gravitational pull, and the greater the wobble of the star. The opposite is true for smaller planets. Therefore, when the planet has a very low mass, the wobble motion of the star continues but with a much smaller amplitude.
5. I am (5) very certain about my claim based on the scientific explanation provided.
6. My certainty rating is influenced by the fact that the explanation is based on scientific principles and has been widely accepted by the scientific community. The
Doppler effect
is well-established, and the relationship between the mass of the planet and the movement of the star is well-understood. Therefore, I am very confident in my answer.
Learn more about
Doppler effect
https://brainly.com/question/1664449
#SPJ11
When an orbiting planet interacts with a star, it causes the star to wobble due to gravitational forces. The wobble's magnitude depends on the planet's mass, with more massive planets causing larger wobbles.
1- The star wobbles when it has an orbiting planet because of the gravitational interaction between the two objects. As the planet orbits the star, it exerts a gravitational force on the star, causing it to move slightly. This motion is known as the "wobble" of the star.
2- The movement of the star is directly related to the mass of the planet. A more massive planet will exert a stronger gravitational force on the star, causing a larger wobble. Conversely, a less massive planet will exert a weaker gravitational force, resulting in a smaller wobble.
3- When the planet has a very low mass, the star continues to wobble. The gravitational force between the star and the planet is still present, although it is relatively weaker compared to the wobble caused by a more massive planet.
4- The star continues to wobble even with a low-mass planet because gravity is always present and exerts a force on both objects. The wobble may be smaller, but it is still observable.
5- I am very certain about this claim based on the fundamental principles of gravity and the understanding that even objects with very small masses can exert gravitational forces.
6- My certainty is influenced by the well-established laws of gravity and the extensive observations and research conducted in the field of astrophysics, which support the relationship between the mass of the planet and the wobble of the star. Additionally, this explanation is consistent with the known behavior of celestial objects in similar situations.
Learn more about gravitational forces
https://brainly.com/question/32609171
#SPJ11
In a Photoelectric effect experiment, the Incldent photons each has an energy of
Part A− How many photons in the incident light hit the metal surface in 5.0 s ?
Incident photons each has an energy of is 0.58 W, (power = energy/ime) Use scientifie notations, format 1.234 ∗
10 n
. The work function of metal surface used is W 0
=2.71eV,1 electron volt (eV)=1.6×10 −18
J. If needed, use h=6.626×10 −34
J⋅s for Planck's constant and c=3.00×10 8
m/s for the speed of light in a vacuum. Part B - What is the max kinetic energy of the photoelectrons? Use scientifie notations, format 1.234 ∗
10 n
. unit is Joules - Part C - Use classical physics fomula for kinetic energy, calculate the maximum speed of the photoelectrons. The mass of an electron is 9.11×10 −31
kg Use scientific notations, format 1.234 ∗
10 n
. unit is m/s
In a Photoelectric effect experiment, the incident photons each have an energy of 0.58 eV. In Part A, we need to determine the number of photons that hit the metal surface in 5.0 seconds.
Part B involves finding the maximum kinetic energy of the photoelectrons, and Part C requires calculating the maximum speed of the photoelectrons using classical physics formulas.
In Part A, we can find the energy of a single photon in Joules by converting the energy given in electron volts (eV) to Joules. Since 1 eV is equal to 1.6 × 10^(-19) Joules, the energy of each photon is 0.58 × 1.6 × 10^(-19) Joules. To determine the number of photons that hit the metal surface in 5.0 seconds, we divide the total energy by the energy of a single photon and then divide it by the time duration.
In Part B, the maximum kinetic energy of the photoelectrons can be calculated by subtracting the work function (given as 2.71 eV) from the incident photon energy (0.58 eV) and converting it to Joules.
In Part C, classical physics formulas can be used to calculate the maximum speed of the photoelectrons. Using the formula for kinetic energy (KE = (1/2)mv^2), where m is the mass of an electron and KE is the maximum kinetic energy calculated in Part B, we can solve for v, the maximum speed of the photoelectrons.
Learn more about the photoelectric effect here:
https://brainly.com/question/9260704
#SPJ11
You pull downward with a force of 31 N on a rope that passes over a disk-shaped pulley of mass of 1.5 kg and a radius of 0.075 m. The other end of the rope is attached to a 0.77 kg mass.
(1) Find the tension in the rope on both sides of the pulley. T1,T2 = (?) N
You pull downward with a force of 31 N on a rope that passes over a disk-shaped pulley of mass of 1.5 kg and a radius of 0.075 m . Therefore, the tension in the rope on both sides of the pulley is:T1 = 25.155 N and T2 = 15.345 N
When a 31N force is applied to a rope that passes over a disk-shaped pulley of mass of 1.5 kg and a radius of 0.075 m, the tension in the rope on both sides of the pulley is as follows:
T1 = (m1g + T2)/(1)T2 = (m2g - T1)/(2)
Where,m1=1.5 kgm2=0.77 kg T1 = tension in the rope on the side with the mass m1, T2 = tension in the rope on the side with the mass m2g = acceleration due to gravity = 9.81 m/s²
T1:T1 = (m1g + T2)/(1)T1 = (1.5 kg × 9.81 m/s² + T2)/(1)
Substitute the given value for T2:31 N = (1.5 kg × 9.81 m/s² + T2)/(1)T2 = (31 N - 1.5 kg × 9.81 m/s²)T2 = 15.345 N
Therefore, T1 = (1.5 kg × 9.81 m/s² + 15.345 N)/(1)T1 = 25.155 N
Therefore, the tension in the rope on both sides of the pulley is:T1 = 25.155 N and T2 = 15.345 N
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
An electric charge Q=+6μc is moving with velocity of v=(3.2×10 6
m/s)i+(1.8×10 6
m/s) j
^
. At a moment, this charge passes the origin of a coordinate. a) Find the B vecor at points M=(−0.3 m,+0.4 m,0.0 m) and N=(+0.2 m,+0.1 m,−0.5 m). Use unit vecotrs to express magnetic field vector. b) Determine if at any point(s) P=(+0.6 m,+0.3 m,0.0 m) and S=(+0.2 m,+0.0 m,−0.5 m) is the magnetic field zero. c) Determine the angle that B vector makes with the Z-axis at point N, in part (a).
An electric charge Q=+6μc is moving with velocity of v=(3.2×10 6 m/s)i+(1.8×10 6 m/s) j. the B vector at points M=(−0.3 m,+0.4 m,0.0 m) and N=(+0.2 m,+0.1 m,−0.5 m) is r = (0.2 m)i + (0.1 m)j + (-0.5 m)k. The unit vector along the Z-axis is given by: k = (0, 0, 1)
To find the magnetic field vector at points M and N, we can use the Biot-Savart law. The Biot-Savart law states that the magnetic field at a point due to a moving charge is proportional to the magnitude of the charge, its velocity, and the distance between the charge and the point.
a) To find the magnetic field at points M and N, we can use the following equation:
B = (μ₀/4π) * (q * v x r) / r³
Where B is the magnetic field vector, μ₀ is the permeability of free space, q is the charge, v is the velocity vector, r is the distance vector from the charge to the point, and x represents the cross product.
Substituting the given values, we have:
μ₀/4π = 10^-7 Tm/A
q = 6 μC = 6 x 10^-6 C
v = (3.2 x 10^6 m/s)i + (1.8 x 10^6 m/s)j
r = position vector from the origin to the point (M or N)
For point M, we have:
r = (-0.3 m)i + (0.4 m)j + (0.0 m)k
Using the formula, we can calculate the magnetic field at point M.
For point N, we have:
r = (0.2 m)i + (0.1 m)j + (-0.5 m)k
Using the formula, we can calculate the magnetic field at point N.
b) To determine if the magnetic field is zero at points P and S, we need to calculate the magnetic field at those points using the Biot-Savart law. If the resulting magnetic field is zero, then the field is zero at those points.
For point P, we have:
r = (0.6 m)i + (0.3 m)j + (0.0 m)k
Using the formula, we can calculate the magnetic field at point P.
For point S, we have:
r = (0.2 m)i + (0.0 m)j + (-0.5 m)k
Using the formula, we can calculate the magnetic field at point S.
c) To determine the angle that the magnetic field vector makes with the Z-axis at point N, we can calculate the dot product of the magnetic field vector and the unit vector along the Z-axis, and then calculate the angle between them using the inverse cosine function.
The unit vector along the Z-axis is given by:
k = (0, 0, 1)
Learn more about Biot-Savart law here:
https://brainly.com/question/30764718
#SPJ11
Which has the greater density—an entire bottle of coke or a
glass of coke?. Explain.
The entire bottle of coke has a greater density than a glass of coke.
The density of the substance is determined by dividing the mass of the substance by its volume. When comparing the entire bottle of Coke to a glass of Coke, we can see that the bottle contains more mass and occupies a larger volume than the glass. The bottle is typically larger and can hold more liquid than a glass. Therefore, the mass of the Coke in the bottle is greater than the mass of the Coke in the glass, and the volume occupied by the Coke in the bottle is larger than the volume occupied by the Coke in the glass. Since the density is calculated by dividing mass by volume, and the mass of the Coke in the bottle is greater while the volume is also greater, the density of the entire bottle of Coke is higher compared to the density of the glass of Coke. Therefore, the entire bottle of coke has a greater density than a glass of coke.
Learn more about density:
https://brainly.com/question/1354972
#SPJ11
he intensity of solar radiation reaching the Earth is 1,340 W/m 2
. If the sun has a radius of 7.000×10 8
m, is a perfect radiator and is located 1.500×10 11
a from the Earth, then what is the temperature of the sun? Multiple Choice 6,430 K 5,740 K 4.230 K 3,210 K 3,670 K
The intensity of solar radiation reaching the Earth is 1,340 W/m 2 . If the sun has a radius of 7.000×10 8 m, is a perfect radiator and is located 1.500×10 11 a from the Earth. Therefore, The temperature of the sun is 6,430 K.
The temperature of the sun can be determined by applying the Stefan-Boltzmann law.
The formula for the Stefan-Boltzmann constant is given byσ = 5.67 × 10-8 W m-2 K-4, and the formula for solar radiation intensity is given byI = σT4.
The intensity of solar radiation reaching the Earth is 1,340 W/m2. If the sun has a radius of 7.000×108m, is a perfect radiator and is located 1.500×1011a from the Earth,
1 The formula for solar radiation intensity is given byI = σT4Where,I = solar radiation intensityσ = Stefan-Boltzmann constantT = temperature of the sun.
2 Rearrange the formula by taking the fourth root of both sides T = (I / σ)1/4.
3 Substitute the values given in the formula: I = 1340 W/m2σ = 5.67 × 10-8 W m-2 K-4.
4 Calculate the distance of the sun from the Earth.
R = 1.5 × 1011 m.
5 Calculate the area of the sun.
A = πr2A
= π (7.0 × 108 m)2A
= 1.539 × 1028 m2.
6 Calculate the total radiation from the sun.
P = IA.P = 1,340 W/m2 × 1.539 × 1028 m2P = 2.059 × 1031 W.
7 Substitute the value of the radiation from the sun in the formula.P = σA(T4 - Ts4)2.059 × 1031 W = 5.67 × 10-8 W m-2 K-4 × 1.539 × 1028 m2 (T4 - Ts4)
8 Rearrange the formula.T4 - Ts4 = (2.059 × 1031 W) / (5.67 × 10-8 W m-2 K-4 × 1.539 × 1028 m2)T4 - Ts4 = 2.961.5332722 × 107 K4Step 9Take the fourth root of both sides. T = [(2.961.5332722 × 107 K4)1/4] + TsT = 6,430 K.
Therefore, The temperature of the sun is 6,430 K.
Learn more about Stefan-Boltzmann constant here:
https://brainly.com/question/30765962
#SPJ11
A long straight current wire is aligned at direction perpendicular to the page. It produces a magnetic field with its directions clockwise around the wire. The direction of the current should point to the right the left downward into the page out of the page upward
When a long straight current wire is aligned at direction perpendicular to the page, it produces a magnetic field with its direction clockwise around the wire. The direction of the current should point to the left.If a long straight current wire is placed perpendicular to the page, it will generate a magnetic field. The magnetic field can be found using the right-hand thumb rule. The direction of the magnetic field is clockwise around the wire.
The direction of the current will depend on the direction of the magnetic field.The left-hand rule is used to find the direction of the current in a wire. The left-hand rule is also called the Fleming’s left-hand rule. The left-hand rule can be used to determine the direction of the force acting on a conductor in a magnetic field. The left-hand rule can be used for finding the direction of a force in any electric motor or generator.In the case of the wire, the direction of the current should point to the left.
The magnetic field generated by the wire will be clockwise around the wire. When the current flows through the wire, it generates a magnetic field around the wire. The direction of the magnetic field depends on the direction of the current.The direction of the magnetic field can be found using the right-hand thumb rule. The right-hand thumb rule is a simple way to find the direction of the magnetic field. To use the right-hand thumb rule, point your thumb in the direction of the current, and then curl your fingers around the wire.
The direction of your fingers will indicate the direction of the magnetic field.The direction of the current can also be found using the left-hand rule. The left-hand rule is also called the Fleming’s left-hand rule. To use the left-hand rule, point your index finger in the direction of the magnetic field, and your middle finger in the direction of the current. Your thumb will point in the direction of the force acting on the conductor. The left-hand rule can be used to find the direction of the force acting on a conductor in a magnetic field.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
What is meant by the principle of moments
A rope is wrapped around a pulley of radius 2.35 m and a moment of inertia of 0.14 kg/m². If the rope is pulled with a force F, the resulting angular acceleration of the pulley is 18 rad/s². Determine the magnitude of the force F. Give your answer to one decimal place.
The magnitude of the force F is 1.1 N to one decimal place.
The pulley is encircled by a rope with a radius of 2.35 m. It has a moment of inertia of 0.14 kg/m².
If a force F is applied to the rope, the pulley has an angular acceleration of 18 rad/s².
The objective is to determine the magnitude of force F.
The torque on the pulley is given by the product of the moment of inertia and the angular acceleration:
τ = Iα
where τ is torque, I is the moment of inertia, and α is angular acceleration.
Substitute the given values to get:
τ = (0.14 kg/m²) (18 rad/s²)
τ = 2.52 N-m
Because the torque on the pulley is produced by the tension in the rope, the force applied is given by:
F = τ / r
where r is the radius of the pulley.
Substitute the values to find F:
F = (2.52 N-m) / (2.35 m)
F = 1.07 N
Therefore, the magnitude of the force F is 1.1 N to one decimal place.
Learn more about magnitude at: https://brainly.com/question/30337362
#SPJ11
A 2-meter rod, whose density is given by (30 + 20x) kg/m. is laid along the x-axis, with its low density end at the origin. A 5.0 kg particle is place on the x-axis 3.0 meter from the origin. Calculate the gravitational force exerted on the particle by the rod. A 2.0-meter rod with mass of 200 kg is laid along the y-axis, with its center of mass at the origin. The density of the rod is uniform. A 5.0 kg particle is place on the x-axis 1 meter from the origin. Calculate the gravitational force exerted on the particle by the rod on the particle.
1. Gravitational force exerted on the particle by the rod with a non-uniform density:
Given, Mass of the particle, m = 5.0 kg
Distance of the particle from the origin, r = 3.0 meters
Density of the rod, ρ = (30 + 20x) kg/m
Length of the rod, L = 2 meters
The rod can be considered as a combination of small elements of length dx at a distance x from the origin.
The mass of each element of the rod, dm = ρdx.The force exerted by the small element on the particle is given by
dF = G × dm × m / r²where G is the gravitational constant.
The total force exerted on the particle by the rod is
F = ∫dF = G × m × ∫(ρdx / r²)
= G × m × ∫[30/r² + (20/r²)x] dx
= G × m [30x / r² + 10x² / r²]2.
Gravitational force exerted on the particle by the rod with uniform density:
Given, Mass of the particle, m = 5.0 kg
Distance of the particle from the origin, r = 1 meter
Mass of the rod, M = 200 kg
Length of the rod, L = 2 meters
The rod can be considered as a combination of small elements of length dx at a distance x from the origin. The mass of each element of the rod, dm = M/L.The force exerted by the small element on the particle is given by
dF = G × dm × m / r²where G is the gravitational constant.
The total force exerted on the particle by the rod is
F = ∫dF
= G × m × ∫(M / Lr²) dx
= G × m × M / L × ∫dx / r²
= G × m × M / Lr² × x
Learn more about Gravitational force exerted here
https://brainly.com/question/27943482
#SPJ11
A 50-cm-diameter pipeline in the Arctic carries hot oil where the outer surface is maintained at 30°C and is exposed to a surrounding temperature of -12°C. Aspecial powder insulation 5 cm thick surrounds the pipe and has a thermal conductivity of 7mW/m°C.The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2°C. Estimate the energy loss from the pipe per meter of length.
To estimate the energy loss from the pipe per meter of length, we consider the heat transfer through conduction and convection.
The heat transfer through conduction can be calculated using the formula: Q_conduction = (k * A * (T_inner - T_outer)) / d,
Q_conduction = (0.007 W/m°C * π * (0.5 m)² * (30°C - (-12°C))) / 0.05 m.
Next, we need to calculate the heat transfer through convection using the formula:
Q_convection = h * A * (T_inner - T_surrounding),
Q_convection = 9 W/m²°C * π * (0.5 m)² * (30°C - (-12°C)).
Calculating this expression, we find the heat transfer through convection.
Finally, we can find the total energy loss per meter of length by adding the heat transfer through conduction and convection.
Please note that the numerical values provided in the question were not specified, so the final result will depend on the specific values used.
Learn more about energy here;
https://brainly.com/question/8101588
#SPJ11
Consta When the glider has traveled along the air track 0.900 m from its initial position against the compressed spring, is it still in contact with the spring? Yes No A small glider is placed against a compressed spring at the bottom of an air track that slopes upward at an angle of 37.0° above the horizontal The glider has mass 7.00x 10-2 kg. The spring has 640 N/m and negligible mass. When the spring is released, the glider travels a maximum distance of 1.90 m along the air track before sliding back down. Before reaching this maximum distance, the glider loses contact with the spring.
What is the kinetic energy of the glider at this point? Express your answer in joules.
The kinetic energy of the glider when it loses contact with the spring is equal to the potential energy stored in the compressed spring, which is 259.2 Joules.
To determine the kinetic energy of the glider when it loses contact with the spring, we need to consider the conservation of mechanical energy.
The initial potential energy stored in the compressed spring is converted into kinetic energy as the glider moves along the air track.
At the point where the glider loses contact with the spring, all of the initial potential energy is converted into kinetic energy.
The potential energy stored in the compressed spring can be calculated using the formula:
Potential energy = (1/2) k [tex]x^2[/tex]
where k is the spring constant and x is the compression or displacement of the spring.
Given that the spring constant is 640 N/m and the glider has traveled 0.900 m against the compressed spring, we can calculate the potential energy:
Potential energy = (1/2) * 640 * [tex](0.900)^2[/tex] = 259.2 J
Therefore, the kinetic energy of the glider when it loses contact with the spring is equal to the potential energy stored in the compressed spring, which is 259.2 J.
So, the kinetic energy of the glider at this point is 259.2 Joules.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Calculate the minimum energy required to remove one neutron from the nucleus !".This is called the neutron-removal energy. (Hint:Find the difference between the mass of a }'O nucleus and the mass of a neutron plus the mass of the nucleus formed when a neutron is removed from '0) 2. How does the neutron-removal energy for O compare to the binding energy per nucleon tor O, calculated using the equation below? Bb - (2M, + Nm. - M)
For O, the neutron-removal energy is much greater than the binding energy per nucleon because it is positive, while the binding energy per nucleon is negative. In conclusion, the neutron-removal energy for O is 1.91 MeV, whereas the binding energy per nucleon for O is 0.867 MeV/u.
The minimum energy required to remove one neutron from the nucleus is referred to as the neutron-removal energy. The difference between the mass of an O nucleus and the mass of a neutron plus the mass of the nucleus created when a neutron is removed from O will be used to calculate the neutron-removal energy.To begin, the atomic mass of O is 16.000u. The atomic mass of a neutron is 1.0087u. When one neutron is removed from O, it becomes an O' isotope with a mass of 15.003u. The neutron-removal energy for O is determined using the following equation:Neutron-removal energy for O = (16.000u - (1.0087u + 15.003u)) × (1.661 × 10-27 J/u)
Neutron-removal energy for O = (16.000u - 16.0117u) × (1.661 × 10-27 J/u)
Neutron-removal energy for O = -0.191 × 10-26 J
Neutron-removal energy for O = 1.91 MeVFor O, the binding energy per nucleon (BE/A) can be calculated using the following formula:Bb - (2M + Nm - M) = (2 × 7.289) + (8 × 1.0087) - 15.994 = 13.8721 MeV
BE/A for O = 13.8721 MeV/16.000u = 0.867 MeV/u
Therefore, for O, the neutron-removal energy is much greater than the binding energy per nucleon because it is positive, while the binding energy per nucleon is negative. In conclusion, the neutron-removal energy for O is 1.91 MeV, whereas the binding energy per nucleon for O is 0.867 MeV/u.
Learn more about energy here,
https://brainly.com/question/20658080
#SPJ11
A person carries a plank of wood 2 m long with one hand pushing down on it at one end with a force F1F1 and the other hand holding it up at 0.75 m from the end of the plank with force F2F2. If the plank has a mass of 24 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1F1 and F2F2?
F1= Unit=
F2= Unit=
The magnitude of F1 is twice that of F2. The unit of force can be expressed in newtons (N) or any other appropriate unit of force.
The torques acting on the plank are determined by the forces F1 and F2 and their respective lever arms. The torque equation is given by τ = F * r * sin(θ), where τ is the torque, F is the force, r is the lever arm, and θ is the angle between the force and the lever arm.
Since the plank is in equilibrium, the sum of the torques acting on it must be zero. Considering the torques about the center of gravity, we have F1 * L/2 * sin(90°) - F2 * L/4 * sin(90°) = 0, where L is the length of the plank.
Simplifying the equation, we find F1 * L/2 = F2 * L/4. Given that L = 2 m, we can solve for the magnitude of F1 and F2. Dividing both sides by L/2, we get F1 = 2 * F2.
Learn more about gravity here:
https://brainly.com/question/31321801
#SPJ11
Katarina wonders in what quadrant(s) tan θ is always positive and why. Which of Dacia's responses is correct? A. "Quadrant III, because sin θ and cos θ are both negative, and negative divided by negative is positive." B. "Quadrant II, because sin θ and cos θ have opposite signs." C. "Both quadrant I and quadrant III, because in these two quadrants sin θ and cos θ have the same sign, and the quotient of two values with the same sign is always posit D. "Quadrant 1, because sin θ and cos θ are both positive, and positive divided by positive is positive."
Answer: According to the given options, Dacia's response D is correct which is Quadrant 1, because sin θ and cos θ are both positive, and positive divided by positive is positive.
The six trigonometric functions are sine, cosine, tangent, cosecant, secant, and cotangent. Tan is one of the six trigonometric functions that describes the relationship between an angle of a right triangle and its opposite side to its adjacent side. It is the ratio of the length of the side opposite the angle to the length of the adjacent side to the angle.
Tan(θ) = opposite / adjacent
Where,θ = angle opposite = opposite side adjacent = adjacent side.
The tangent function is positive in Quadrant 1 because both the opposite and adjacent sides are positive.
In Quadrant 2, the opposite side is positive, but the adjacent side is negative, resulting in a negative tangent value.
In Quadrant 3, both the opposite and adjacent sides are negative, resulting in a positive tangent value.
In Quadrant 4, the opposite side is negative, but the adjacent side is positive, resulting in a negative tangent value.
Therefore, the correct answer is quadrant I because sin θ and cos θ are both positive, and positive divided by positive is positive.
Learn more about trigonometric functions: https://brainly.com/question/25618616
#SPJ11
A charged particle causes an electric flux of −2600.0 N⋅m2/C to pass through a spherical Gaussian surface of radius R centered on the charge. What is the charge of the particle?
The electric flux can be defined as the amount of electric field that passes through a given area. According to Gauss's law, the electric flux passing through a closed Gaussian surface is equal to the net electric charge enclosed within the surface divided by the permittivity of the free space (ε₀).
The formula for calculating the electric flux through a closed surface is as follows:
ϕ = ∮E⋅dA where, ϕ is the electric flux, E is the electric field, dA is the differential area vector
We can use the same formula to calculate the electric charge of the particle.
ϕ = Q/ε₀ Where, Q is the electric charge, ε₀ is the permittivity of free space
ϕ = -2600.0 N.m²/C
For a spherical Gaussian surface, Q/ε₀ = -2600.0 N.m²/C
Q = ε₀ × ϕQ = (8.85 × 10⁻¹² C²/N.m²) × (-2600.0 N.m²/C)
Q = -0.023 N or 2.3 × 10⁻² C
Therefore, the charge of the particle is 2.3 × 10⁻² C
Learn about Gauss' law here: https://brainly.com/question/14773637
#SPJ11
The critical angle in air for a particular type of material is 42.0 ∘
. What is the speed of light in this material in 10 8
m/s ? Use three significant digits please.
The speed of light in this material is approximately 2.00 × 10^8 m/s (to three significant digits).
To determine the speed of light in a particular material, we can use Snell's law, which relates the refractive indices of the two media:
n1*sin(theta1) = n2*sin(theta2)
Where:
n1 is the refractive index of the initial medium (air, in this case)
theta1 is the angle of incidence (measured from the normal)
n2 is the refractive index of the second medium (the material)
theta2 is the angle of refraction (measured from the normal)
Given that the critical angle in air for the material is 42.0 degrees, we can find the refractive index (n2) using the equation:
n2 = 1 / sin(critical angle)
Substituting the value, we get:
n2 = 1 / sin(42.0 degrees) ≈ 1.499
Now, the speed of light in a medium is related to the refractive index by the equation:
v = c / n
where:
v is the speed of light in the material
c is the speed of light in vacuum (approximately 3.00 × 10^8 m/s)
Substituting the values, we have:
v = (3.00 × 10^8 m/s) / 1.499 ≈ 2.00 × 10^8 m/s
Therefore, the speed of light in this material is approximately 2.00 × 10^8 m/s (to three significant digits).
Learn more about speed of light
https://brainly.com/question/29216893
#SPJ11
linear boundary of the field, as shown in the figure below. Calculate the distance x from the point of entry to where the proton leaves the field. Tries 0/10 Determine the angle between the boundary and the proton's velocity vector as it leaves the field.
The angle between the boundary and the proton's velocity vector, as it leaves the field, is 52.5°.
Given:
Let E = 30.0 N/C, d = 0.020 m, v = 3.0 × 107 m/s.
The magnetic field is directed out of the page and has a magnitude of B = 0.800 T. The length of the linear boundary of the field is L = 0.150 m.
To find: Calculate the distance x from the point of entry to where the proton leaves the field. Determine the angle between the boundary and the proton's velocity vector as it leaves the field.
From the diagram, we can see that the proton enters the field with some initial velocity v0 that makes an angle θ with the horizontal. After traversing the field, the proton will leave it at some distance x from where it entered.
To find x, we need to find the time t that the proton spent in the field. Since the magnetic force is perpendicular to the velocity, it does not change the speed of the proton, only its direction. Therefore, we can use the definition of acceleration, a = Δv/Δt to find t.
We know that the magnetic force is given by F = qvB sinθ. Since F = ma, we have ma = qvB sinθ, orma = qvB sinθSolving for the acceleration, we geta = qvB sinθ/mWe can use the definition of acceleration again, this time in the x-direction, where there is no magnetic force, to find t. We know that ax = 0 = Δvx/Δt
Solving for t, we get
t = x/vxSincevx = v0 cosθ, we have
t = x/v0 cosθ
Solving for x, we get
x = v0 cosθ t = v0 cosθ (d/v0 sinθ)/v0 cosθ = d/v0 sinθ
Therefore,x = d/v0 sinθx = (0.020 m)/(3.0 × 107 m/s) sinθ
x = (6.7 × 10-8 m)/sinθ
The angle between the boundary and the proton's velocity vector, as it leaves the field, is given by the angle between the tangent to the boundary at that point and the velocity vector.
Since the boundary is a straight line, its tangent is parallel to itself. Therefore, the angle between it and the velocity vector is the same as the angle between the boundary and the horizontal, which is given by
arctan(L/2d) = arctan(0.150 m/2 × 0.020 m) = 52.5°
Question: A proton moving in the plane of the page has a kinetic energy of 6.00MeV. A magnetic field of magnitude B=1.00T is directed into the page. The proton enters the magnetic field with its velocity vector at an angle θ=45.0 to the linear boundary of the field as shown in Figure.
(a) Find x, the distance from the point of entry to where the proton will leave the field.
(b) Determine θ, the angle between the boundary and the proton's velocity vector as it leaves the field.
To learn about velocity vectors here:
https://brainly.com/question/28491008
#SPJ11
A circular hole in an aluminum plate is 3.704 cm in diameter at 0.000 ∘
C. What is its diameter (in cm ) when the temperature of the plate is raised to 57.34 ∘
C ? The linear expansion coefficient of aluminum is 23.00×10 −6
/C ∘
4.21 3.98 2.56 3.71
When the temperature of the plate is raised to 57.34 °C, the diameter of the hole in the aluminum plate is approximately 3.7504 cm.
To calculate the change in diameter of the hole in the aluminum plate when the temperature is raised, we can use the formula for linear thermal expansion:
ΔD = α * D * ΔT
Where:
ΔD is the change in diameter
α is the linear expansion coefficient
D is the original diameter
ΔT is the change in temperature
Given:
Original diameter (at 0.000 °C) = 3.704 cm
Change in temperature (ΔT) = 57.34 °C
Linear expansion coefficient (α) = 23.00 × 10^(-6) / °C
Substituting the values into the formula, we have:
ΔD = (23.00 × 10^(-6) / °C) * (3.704 cm) * (57.34 °C)
ΔD ≈ 0.0464 cm
To find the new diameter, we add the change in diameter to the original diameter:
New diameter = Original diameter + ΔD
New diameter ≈ 3.704 cm + 0.0464 cm
New diameter ≈ 3.7504 cm
Therefore, when the temperature of the plate is raised to 57.34 °C, the diameter of the hole in the aluminum plate is approximately 3.7504 cm.
Learn more about thermal expansion here:
https://brainly.com/question/30925006
#SPJ11
The pressure of a non relativistic free fermions gas in 2D depends at T=0. On the density of fermions n as
The pressure of a non-relativistic free fermion gas in 2D depends at T=0 on the density of fermions n asP = πħ²n²/2mIt can be derived from the following equation, which relates the pressure and energy of a 2D non-relativistic free fermion gas at T = 0:E = πħ²n²/2m.
The pressure of a non-relativistic free fermion gas in 2D depends at T=0. On the density of fermions n as P = πħ²n²/2mWhere, P is the pressure of a non-relativistic free fermion gas in 2D. ħ is Planck's constant divided by 2π. m is the mass of the fermion. n is the density of fermions.Further ExplanationThe pressure of a non-relativistic free fermion gas in 2D depends at T=0 on the density of fermions n asP = πħ²n²/2mIf there is a 2D gas made up of fermions with a fixed density, and no other forces are acting on the system, then it follows that the energy and momentum are conserved. The pressure in a gas is determined by the momentum of the particles colliding with the walls of the container. In this case, the gas is in 2D, so the momentum must be calculated in the plane. It follows that the total momentum is given by P = 2kFnWhere, kF is the Fermi wave number of the 2D system. Therefore, the pressure of a non-relativistic free fermion gas in 2D depends at T=0 on the density of fermions n asP = πħ²n²/2mIt can be derived from the following equation, which relates the pressure and energy of a 2D non-relativistic free fermion gas at T = 0:E = πħ²n²/2m.
Learn more about Equation here,What is equation? Define equation
https://brainly.com/question/29174899
#SPJ11
A broken tree branch is dragged 5 m up a hill by a 30 N force, 24⁰ to the horizontal. The inclination of
the hill is 15° to the level ground. At the top of the hill, the tree branch is dragged by the same force
horizontally across the level ground for 22 m. Find the total work done to one decimal place.
The force applied is still 30 N, and the displacement is 22 m. The force is applied horizontally, the angle θ between the force and displacement vectors is 0° (cos(0°) = 1).
a) Work done when dragging the tree branch up the hill: The work done (W) is given by the formula W = F * d * cos(θ), where F is the force applied, d is the displacement, and θ is the angle between the force and displacement vectors. (b) Work done when dragging the tree branch horizontally across the level ground: Since the force is applied horizontally, the angle θ between the force and displacement vectors is 0° (cos(0°) = 1). The force applied is still 30 N, and the displacement is 22 m.
(a) To calculate the work done when dragging the tree branch up the hill, we use the formula W = F * d * cos(θ), where F is the force applied, d is the displacement, and θ is the angle between the force and displacement vectors. By substituting the given values into the formula, we can calculate the work done when dragging the tree branch up the hill.
(b) When dragging the tree branch horizontally across the level ground, the angle θ between the force and displacement vectors is 0°, as the force is applied horizontally. By using the same formula as in part (a), with the appropriate values, we can calculate the work done when dragging the branch horizontally across the level ground.
To find the total work done, we sum the work done when dragging the branch up the hill and the work done when dragging it horizontally across the level ground. By adding the two values together, we obtain the total work done to one decimal place.
Learn more about work done here:
https://brainly.com/question/32263955
#SPJ11