Answer:on april 20th at aproximately 12: 12 a.m
Mrs. Jones is pulling a rope at 73 newtons, and a student
is pulling a rope at 47 newtons. What is the net force
(calculation).
The net force on the object is 26 newtons. Some common types of forces include gravitational force, electromagnetic force, and the force of friction.
What is Force?
Force is a physical quantity that is used to describe the interaction between two objects. It is defined as any influence that causes an object to undergo a change in motion or direction. Force is typically measured in units of newtons (N), and it has both magnitude (strength) and direction. The direction of a force is typically described by its vector, which can point in any direction in three-dimensional space.
To calculate the net force, we need to add up the forces acting on the object.
In this case, the forces are being applied in opposite directions, so we need to subtract the smaller force from the larger force.
Net force = 73 N - 47 N = 26N
Learn more about Force from the given link
https://brainly.com/question/12785175
#SPJ1
Determine the cross-sectional area of an aluminum wire if its resistance is 0.1 ohm and its mass is 54 grams.
an air-filled parallel-plate capacitor has a capacitance of 4.0 pf. the separation of the plates is doubled and wax is inserted between them. the new capacitance is 8.0 pf. find the dielectric constant of the wax.
The capacitance of an air-filled parallel-plate capacitor is 4.0 pf. Wax is placed between the pieces as they are double separated. The dielectric constant of the wax is approximately 0.903.
The capacitance of an air-filled parallel-plate capacitor is given by:
C = ε0 × A / d
where C is the capacitance, ε0 is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.
Given that the initial capacitance of the capacitor is 4.0 pF, we can rearrange the equation to solve for the initial plate separation:
d = ε0 × A / C1
where C1 is the initial capacitance. Substituting the given values, we have:
d = (8.85 x 10^-12 F/m) × A / 4.0 pF
= 2A × 10^-3 m
Next, we are told that the plate separation is doubled and wax is inserted between the plates, resulting in a new capacitance of 8.0 pF. We can use the same equation to find the new plate separation:
d' = ε0 × A / C2
where C2 is the new capacitance. Substituting the given values, we have:
d' = (8.85 × 10^-12 F/m) × A / 8.0 pF
= A × 10^-3 m
To find the dielectric constant of the wax, we can use the formula:
C2 = εr × ε0 × A / d'
where εr is the relative permittivity (dielectric constant) of the wax. Substituting the values we have calculated, we get:
8.0 pF = εr × (8.85 × 10^-12 F/m) × A / (A × 10^-3 m)
Simplifying, we get:
εr = 8.0 / 8.85 = 0.903
It's worth noting that this calculation assumes that the area of the plates remains constant when the wax is inserted. In practice, the insertion of the wax may affect the plate geometry, which could affect the capacitance. Additionally, the dielectric constant of the wax may depend on factors such as temperature and frequency.
To learn more about dielectric constant
https://brainly.com/question/13265076
#SPJ4
Describe how the wavelength and the frequency of a wave are related
in aviation a standard rate turn proceeds at an angular speed of per minute. what is the radius of a standard rate turn for a plane moving at 240 m/s?
The radius of a standard rate turn for a plane moving at 240 m/s is approximately 933 meters.
A standard rate turn in aviation refers to a turn in which an aircraft completes a full 360-degree rotation in 2 minutes, resulting in an angular speed of 3 degrees per second (180 degrees per minute). To calculate the radius of a standard rate turn for a plane moving at 240 m/s, we can use the formula:
Radius = V / (G × Tan(Bank Angle))
where:
- V is the velocity of the plane (240 m/s)
- G is the gravitational constant (approximately 9.81 m/s²)
- Bank Angle is the angle at which the aircraft is tilted during the turn.
First, we need to find the bank angle. Since we know that the angular speed is 3 degrees per second, we can use the following formula to find the bank angle:
Bank Angle = Arc Tan((V² × Angular Speed) / (G × 180))
Bank Angle = Arc Tan((240² × 3) / (9.81 × 180))
Bank Angle ≈ 14.7 degrees
Now that we have the bank angle, we can calculate the radius of the turn:
Radius = 240 / (9.81 × Tan(14.7))
Radius ≈ 933 meters
So, the radius of a standard rate turn for a plane moving at 240 m/s is approximately 933 meters.
Know more about Bank Angle here:
https://brainly.com/question/30905320
#SPJ11
doubling only the spring constant of a vibrating mass-and-spring system produces what effect on the system's mechanical energy? increases the energy by a factor of two increases the energy by a factor of square root of two increases the energy by a factor of three increases he energy by a factor of four produces no change\
When doubling only the spring constant of a vibrating mass-and-spring system, the effect on the system's mechanical energy is to increase the energy by a factor of four. A mass and spring system is a simple harmonic oscillator that can move back and forth when displaced from equilibrium.
When a spring is extended or compressed, it exerts a force in the opposite direction, which causes the mass to accelerate. When the mass reaches equilibrium, the spring force balances the force of gravity acting on the mass.
The force of a spring can be expressed as F = -kx, where k is the spring constant and x is the displacement from equilibrium. The amount of energy stored in the spring can be calculated by the following formula: E = 1/2 kx²When the spring constant k is doubled, the potential energy stored in the spring is doubled.
This means that if the displacement from equilibrium remains constant, the mechanical energy will double. Thus, doubling only the spring constant of a vibrating mass-and-spring system produces an effect on the system's mechanical energy that increases the energy by a factor of four.
To know more about oscillation, refer here:
https://brainly.com/question/17133973#
#SPJ11
in a single slit experiment, what effect on the central minimum in the diffraction pattern would result as the wavelength of the light is decreased?
In a single-slit experiment, decreasing the wavelength of light would result in a narrower central minimum in the diffraction pattern.
The width of the central minimum in a single-slit diffraction pattern is inversely proportional to the wavelength of light. When the wavelength decreases, the angle at which the first minimum occurs increases according to the formula
θ = λ / a, where θ is the angle, λ is the wavelength, and a is the slit width.
As the angle increases, the width of the central minimum becomes narrower. This change in the diffraction pattern can be observed as the separation between adjacent bright fringes, or maxima, increases when the light wavelength is decreased.
To know more about single-slit experiment click on below link:
https://brainly.com/question/31369458#
#SPJ11
a 0.800-kg copper rod rests on two horizontal rails 0.500 m apart and carries a current of 53.0 a from one rail to the other. the coefficient of static friction between rod and rails is 0.330. what is the magnitude and direction of the smallest magnetic field that puts the rod on the verge of sliding? give the direction relative to the vertical. magnitude: direction:
The magnitude of the smallest magnetic field that puts the rod on the verge of sliding is 0.0559 T.
The force required to overcome the static friction between the copper rod and the rails is given by:
fs = μs * N
where μs is the coefficient of static friction, N is the normal force, and fs is the force required to overcome static friction.
In this case, the normal force is equal to the weight of the rod, which is given by:
N = mg
where m is the mass of the rod and g is the acceleration due to gravity.
The magnetic force on the rod is given by:
Fm = BIL
where B is the magnetic field strength, I is the current in the rod, and L is the length of the rod.
For the rod to be on the verge of sliding, the magnetic force must be equal to the force required to overcome static friction:
Fm = fs
Substituting the given values and solving for B, we get:
B = fs / IL
B = μs × N / IL
B = μs × mg / IL
B = (0.330) × (0.800 kg) × (9.81 m/s^2) / (0.500 m × 53.0 A)
B = 0.0559 T
The direction of the magnetic field relative to the vertical is perpendicular to the plane of the rails and into the page, because the direction of the magnetic force is perpendicular to both the direction of the magnetic field and the direction of the current, as determined by the right-hand rule.
To learn more about magnetic fields
https://brainly.com/question/11514007
#SPJ4
what type of reaction occurs when a cadle is burned
Answer:
Exothermic Reaction.
Explanation:
An exothermic reaction is a chemical reaction that releases energy in the form of light or heat. The burning of the candle is an exothermic reaction. Endothermic reactions - Heat is absorbed, like the Photosynthesis process.
6. a 60 kw pump is used to pump up water from a mine that is 40 m deep. find the mass of water that can be lifted by the pump in 1.2 min.
We can substitute all the values in the formula for mass of water lifted:mass of water lifted = power x time / work done against gravity x efficiency= 60 x 72 / (1232.56r²) x 0.8= 26.25/r² kgAnswer: mass of water lifted = 26.25/r² kg.
To find the mass of water that can be lifted by a 60 kW pump in 1.2 minutes from a mine that is 40 m deep, we use the following formula:mass of water lifted = power x time / work done against gravity x efficiencyWe know that the power of the pump is 60 kW, the depth of the mine is 40 m, and the time taken is 1.2 minutes or 72 seconds. The efficiency of the pump is not given, so we assume it to be 80%.Now, we need to find the work done against gravity. The work done against gravity is equal to the weight of the water lifted. The weight of water is given by the formula:weight of water = mass x gravitywhere gravity is 9.8 m/s²Substituting the values, we get:weight of water = volume of water x density x gravitySince we are not given the density of water, we assume it to be 1000 kg/m³.Substituting the values, we get:work done against gravity = weight of water x depth of mine= volume of water x density x gravity x depth of mine= πr² x h x 1000 x 9.8 x 40= 1232.56r²Now, we can substitute all the values in the formula for mass of water lifted:mass of water lifted = power x time / work done against gravity x efficiency= 60 x 72 / (1232.56r²) x 0.8= 26.25/r² kg.
Learn more about mass of water here:
https://brainly.com/question/29269842
#SPJ4
A container holds a gas consisting of 9.75 moles of oxygen molecules. One in a million of these molecules has lost a single electron. NA=6.022×10^23mol−1, e=1.60×10^−19C
The oxygen molecules have lost a total of 0.94 coulombs in charge of their electrons.
How did Avogadro's number, 6.022 x 1023, come to be?AVOGADO'S CALL SIGN-
Amadeo Avogadro (1776–1856), an Italian chemist, stated the principle in 1811 that equivalent volumes of gases under the same temperature and stress contain an equal range of molecules regardless of the molecules' chemical make-up and physical characteristics. It is 6.023 x 1023, or Avogadro's number.
Learn more about container . here;
https://brainly.com/question/11619692
#SPJ1
a spring is stretched by 16.8cm. if the spring constant of the spring is 71.8n/m. how much elastic potential energy (in unit of joule) is stored in the spring?
The elastic potential energy stored in the spring is approximately 1.01 Joules. To calculate the elastic potential energy stored in the spring, we will use the formula for the potential energy of a spring, which is:
PE = (1/2) * k * x^2
where PE is the elastic potential energy, k is the spring constant, and x is the stretch or compression distance.
From the student question, we know that the spring constant (k) is 71.8 N/m, and the spring is stretched by 16.8 cm. To use the formula, we need to convert the stretch distance to meters:
[tex]16.8 cm = 16.8/100 m = 0.168 m[/tex]
Now, we can plug the values into the formula:
[tex]PE = (1/2) * 71.8 N/m * (0.168 m)^2[/tex]
To calculate the potential energy, first square the stretch distance:
[tex](0.168 m)^2 = 0.028224 m^2[/tex]
Next, multiply the spring constant by the squared stretch distance:
[tex]71.8 N/m * 0.028224 m^2 = 2.0262272 Nm[/tex]
Finally, multiply the result by 1/2:
[tex](1/2) * 2.0262272 Nm = 1.0131136 J[/tex]
to know more about potential energy refer here:
https://brainly.com/question/12807194#
#SPJ11
what is the relationship between magnetic force and the angle between the current carrying wire and the magnetic filed
The magnetic force on a present-day-carrying twine is without delay proportional to the strength of the magnetic area and the contemporary within the twine and is also dependent on the angle among the route of the modern and the course of the magnetic field.
Magnetic force is a fundamental force that arises from the motion of charged particles. It is the force that causes magnets to attract or repel each other, and it is also responsible for the behavior of electrically charged particles in the presence of a magnetic field. The strength of the magnetic force depends on the strength of the magnetic field and the velocity and charge of the particles.
The route of the pressure is perpendicular to each the magnetic subject and the rate of the particle. Magnetic force plays an important role in many areas of physics, including electromagnetism, quantum mechanics, and particle physics. It is essential for understanding the behavior of electromagnetic waves, the functioning of electric motors and generators, and the behavior of charged particles in particle accelerators.
To learn more about Magnetic force visit here:
brainly.com/question/3160109
#SPJ4
what are the dimensions (height and width) of the smallest plane mirror that you can buy so that you can still see all of yourself without having to move your head? 2. at what position should you mount the mirror on the wall?
To see your entire body in a plane mirror without moving your head, you need a mirror at least half your height. This is because the angle of incidence equals the angle of reflection, allowing you to see your full body in a mirror half your size.
1. Dimensions: Assuming an average human height of 5'6" (66 inches) for simplicity, the height of the smallest mirror should be 33 inches. The width should be wide enough to cover the widest part of your body, usually the shoulders, but it depends on the person's size. Let's say around 18-24 inches as an average width.
2. Position: To ensure you can see your entire body, the mirror should be mounted vertically, centered at the midpoint of your height. Considering the average height of 5'6" (66 inches), the midpoint would be 33 inches above the floor. This will allow you to see your full body without moving your head.
to know more about plane mirror refer here:
https://brainly.com/question/1160148#
#SPJ11
9. Which of the following is true about insulators?
A) Insulators have very tightly bound valance electrons.
B) Insulators do not allow electricity to flow through it easily.
C) ceramic and glass are examples of good insulators.
D) All of the above
a mass on a 500 n/m spring is submersed in a liquid. it is pulled down 4 cm from the equilibrium position and released. after ten seconds, the amplitude has been dampened to 3 cm. how much energy did the liquid gain during those ten seconds, in j?
The liquid gained 0.175 J of energy during the ten-second period.
The initial potential energy of the spring-mass system is:
U = [tex](1/2)kx^2 = (1/2)(500 N/m)(0.04 m)^2 = 0.4 J[/tex]
The amplitude of the oscillation decreases from 4 cm to 3 cm over 10 seconds, so the damping constant is:
b = ln(4/3)/(10 s) ≈ 0.0337 s^-1
The general equation for the motion of a damped harmonic oscillator is:
x(t) = A exp(-bt/2m) cos(ωt + φ)
The angular frequency is related to the spring constant and mass by:
ω = [tex]\sqrt{(k/m)[/tex]
A(t) = A exp(-bt/2m)
After 10 seconds, the amplitude has decreased from 4 cm to 3 cm, so:
3 cm = A exp(-b(10 s)/(2m))
Dividing by the initial amplitude, we get:
0.75 = exp(-b(10 s)/(2m))
Taking the log of each aspects, we get:
ln(0.75) = -b(10 s)/(2m)
Solving for the mass, we get:
m = -b(10 s)/(2 ln(0.75)) ≈ 0.25 kg
The very last capability strength of the machine is:
U' = [tex](1/2)kx'^2 = (1/2)(500 N/m)(0.03 m)^2 = 0.225 J[/tex]
The energy lost due to damping is:
ΔE = U - U' = 0.4 J - 0.225 J = 0.175 J
Energy is essential for all forms of life and for many human activities, such as transportation, heating and cooling buildings, and producing electricity. However, the use of energy also has environmental and social impacts, including greenhouse gas emissions and resource depletion. The development and use of renewable energy sources, such as solar and wind power, is increasingly important for reducing these impacts and ensuring a sustainable energy future.
Thermal energy is the energy that comes from heat, while kinetic energy is the energy of motion. Potential energy is stored energy that can be converted into kinetic energy, such as a ball held up high before being dropped. Chemical energy is the energy stored in the bonds between atoms and molecules, while electromagnetic energy is energy that travels in waves, such as light or radio waves.
To learn more about Energy visit here:
brainly.com/question/8630757
#SPJ4
how often should a fire detection and alarm system backup electrical generator be run under load? answer
When it comes to the frequency with which a fire detection and alarm system backup electrical generator should be run under load, it is recommended that it be run under load at least once a month.
A fire detection and alarm system is a collection of systems that work together to detect and alert occupants to the presence of fire through audio and visual signals.
In addition to being a component of a building's life safety system, fire detection and alarm systems are also utilized to activate fire suppression systems, elevators, and other safety features. Intended to notify emergency services in the event of an alarm, allowing for prompt evacuation and the implementation of any necessary emergency response procedures.When it comes to the detection of fire, fire detection, and alarm systems utilize a variety of technologies, including photoelectric detectors, ionization detectors, and thermal detectors, to detect the presence of fire. Furthermore, once the alarm has been triggered, the system is designed to notify emergency services so that they can respond as quickly as possible to the scene of the fire.Therefore, it is advisable to operate the backup electrical generator of a fire detection and alarm system under load at least once per month.
To know more about fire detection click here:
https://brainly.com/question/14391072
#SPJ11
6. the plate shown on the left is 0.5 m wide perpendicular to the paper. calculate the velocity of the water jet required to hold the plate upright.
The velocity of the water jet required to hold the plate upright is 0.707 m/s. To calculate the velocity of the water jet required to hold the plate upright, the following data is needed: width of the plate perpendicular to the paper = 0.5 m.
For a plate to be held upright by a water jet, the upward force generated by the jet must be equal to the weight of the plate (downward force). The upward force generated by the jet is proportional to the velocity of the water jet. So, the velocity of the water jet required to hold the plate upright can be determined by setting the upward force generated by the jet equal to the weight of the plate.
Mathematically, it can be written as: F_upward = F_downwardor ρAV² = mg where, ρ is the density of the water, A is the cross-sectional area of the water jet, V is the velocity of the water jet, m is the mass of the plate, and g is the acceleration due to gravity.
Using the given data, ρ = 1000 kg/m³ (density of water)A = (π/4)d² = (π/4) x 0.5² = 0.1963 m² (cross-sectional area of the water jet, assuming diameter of the jet as 0.5 m) m = 10 kg (mass of the plate)g = 9.8 m/s² (acceleration due to gravity)
Therefore, substituting these values in the above equation,ρAV² = mg⇒ V = √(mg/ρA)= √(10 × 9.8 / (1000 × 0.1963))= √0.5002= 0.707 m/s Therefore, the velocity of the water jet required to hold the plate upright is 0.707 m/s.
To know more about velocity, refer here:
https://brainly.com/question/17127206#
#SPJ11
characteristic best describes the inner planets? responses made of gases such as hydrogen and helium made of gases such as hydrogen and helium fast rotations fast rotations made of rocks and metals made of rocks and metals lots of moons lots of moons
In terms of the characteristics that best describe the inner planets, it is important to note that the inner planets (Mercury, Venus, Earth, and Mars) are those that orbit closest to the Sun.
As a result, these planets are generally characterized by several shared features, including that they are made of rocks and metals rather than gases such as hydrogen and helium, and they also have relatively fast rotations compared to other planets in the solar system.
The inner planets are also generally smaller and less massive than the outer planets, and they have fewer moons (or, in the case of Mercury, no moons). Additionally, the inner planets are much hotter than the outer planets due to their proximity to the Sun, which results in high temperatures that make it difficult for life to survive on these planets.
For more such questions on inner planets
brainly.com/question/11909438
#SPJ11
A horse pulls a tree trunk there is a force of 1500N. and moves a distance of 10m in 15s find the work and the power.
Answer:
Work=15000
Power=1000
Explanation:
Foce=1500N
Distance=10m
Time=15s
Work=Force*Distance
Work=1500*10=15000Nm
Power=Work/Time=15000/15=1000nm/s
GIVE ME THE ANSWERS TO MY SCIENCE PROJECT PLS!
Directions
Now that the lab is complete, it is time to write your lab report. The purpose of this guide is to help you write a clear and concise report that summarizes the lab you have just completed.
The lab report is composed of two sections:
Section I: Overview of Investigation
Provide background information.
Summarize the procedure.
Section II: Observations and Conclusions
Include any charts, tables, or drawings required by your teacher.
Include answers to follow-up questions.
Explain how the investigation could be improved.
To help you write your lab report, you will first answer the four questions listed below based on the lab that you have just completed. Then you will use the answers to these questions to write the lab report that you will turn in to your teacher.
You can upload your completed report with the upload tool in formats such as OpenOffice.org, Microsoft Word, or PDF. Alternatively, your teacher may ask you to turn in a paper copy of your report or use a web-based writing tool.
Questions
Section I: Overview of Lab
What is the purpose of the lab?
What procedure did you use to complete the lab?
Outline the steps of the procedure in full sentences.
Section II: Observations and Conclusions
What charts, tables, or drawings would clearly show what you have learned in this lab?
Each chart, table, or drawing should have the following items:
An appropriate title
Appropriate labels
If you could repeat the lab and make it better, what would you do differently and why?
There are always ways that labs can be improved. Now that you are a veteran of this lab and have experience with the procedure, offer some advice to the next scientist about what you suggest and why. Your answer should be at least two to three sentences in length.
Writing the Lab Report
Now you will use your answers from the four questions above to write your lab report. Follow the directions below.
Section I: Overview of Lab
Use your answers from questions 1 and 2 (above) as the basis for the first section of your lab report. This section provides your reader with background information about why you conducted this lab and how it was completed. It should be one to two paragraphs in length.
Section II: Observations and Conclusions
Use your answers from questions 3 and 4 (above) as the basis for the second section of your lab report. This section provides your reader with charts, tables, or drawings from the lab. You also need to incorporate your answers to the follow-up questions (from the Student Guide) in your conclusions.
Overall
When complete, the lab report should be read as a coherent whole. Make sure you connect different pieces with relevant transitions. Review for proper grammar, spelling, punctuation, formatting, and other conventions of organization and good writing.
I can provide guidance on how to structure your lab report based on the questions you have provided.
Section I: Overview of LabThe purpose of this section is to provide background information about the lab and to summarize the procedure used to complete the lab. This section should be one to two paragraphs in length.In the first paragraph, you should briefly state the purpose of the lab. This should include a clear statement of the problem or question that the lab is addressing. For example, "The purpose of this lab was to investigate the effect of temperature on the rate of enzyme activity."
In the second paragraph, you should summarize the procedure used to complete the lab. This should include an overview of the steps taken and any materials or equipment used. The procedure should be outlined in full sentences and provide enough detail for the reader to understand what was done. For example, "To complete the lab, we first collected three test tubes and labeled them A, B, and C. We then added 5 ml of the enzyme solution to each tube and placed them in a water bath at 30°C for 10 minutes."Section II :Observations and ConclusionsThe purpose of this section is to present any charts, tables, or drawings required by your teacher and to include answers to follow-up questions. This section should be organized based on the structure of the questions provided.In the first part of this section, you should include any charts, tables, or drawings that would clearly show what you have learned in the lab. Each chart, table, or drawing should have an appropriate title and appropriate labels.
In the second part of this section, you should answer the follow-up question about how the investigation could be improved. Offer some advice to future scientists about what you suggest and why. Your answer should be at least two to three sentences in length.OverallWhen complete, the lab report should be read as a coherent whole. Make sure you connect different pieces with relevant transitions. Review for proper grammar, spelling, punctuation, formatting, and other conventions of organization and good writing. It is important to be clear and concise in your writing and to use appropriate scientific language and terminology.
It takes 5 J of work to compress a monatomic ideal gas in a well-insulated container initially at atmospheric pressure and room temperature (300K) from 16 cc to 3 cc. What is the final pressure of the gas in atm?
We can solve this problem by using the First Law of Thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system:
ΔU = Q - W
Since the container is well-insulated, Q = 0 and therefore ΔU = -W. The change in internal energy is given by:
ΔU = (3/2)nRΔT
where n is the number of moles of gas, R is the gas constant, and ΔT is the change in temperature. Since the gas is monatomic, we can substitute n = N/NA, where N is the number of atoms and NA is Avogadro's number, and use R = kNA, where k is the Boltzmann constant. Then we have:
ΔU = (3/2)(N/NA)kΔT
The work done by the gas is given by:
W = PextΔV
where Pext is the external pressure and ΔV is the change in volume. Since the pressure is constant, we can substitute Pext = Patm, the atmospheric pressure. Then we have:
W = Patm(V2 - V1)
where V1 and V2 are the initial and final volumes, respectively. Substituting the given values, we have:
W = 5 J
V1 = 16 cc = 16×10^-6 m^3
V2 = 3 cc = 3×10^-6 m^3
ΔV = V2 - V1 = -13×10^-6 m^3 (negative because the gas is compressed)
Substituting into the work equation, we get:
5 J = (101325 Pa)(-13×10^-6 m^3)
P = -5/(101325×13×10^-6) atm
P ≈ 0.003 atm
This result is negative, which means that the gas has done work on the surroundings rather than the other way around. This is because we have compressed the gas by doing work on it, and the gas has then expanded against the walls of the container, doing work on the surroundings. To get the final pressure of the gas, we need to add the atmospheric pressure to the pressure change caused by the compression:
Pf = Patm - ΔP = Patm - W/V2 = 1 - 5/(3×10^6) atm
Pf ≈ 0.9983 atm
Therefore, the final pressure of the gas is 0.9983 atm.
To create artificial gravity, the space station shown in the drawing is rotating at a rate of 1.5 rpm. The radii of the cylindrically shaped chambers have the ratio rA/rB = 5.05. Each chamber A simulates an acceleration due to gravity of 6.7 m/s2.
(a) Find rA.
(b) Find rB.
(c) Find the acceleration due to gravity that is simulated in chamber B.
rA is equal to 23.15 metres, rB is equal to 4.58 metres, and the gravity simulation acceleration in chamber B is 0.11 m/s².
One approach to make a space station feel like it has artificial gravity is to spin it?Applying a force to an astronaut that results in an acceleration of 9.8 metres per second, or 32 feet per second, is the only known way to create artificial gravity. Bungee cords, body restraints, or a fast enough spin of the spaceship to generate sufficient centrifugal acceleration can all be used to accomplish this.
6.7 = rA(0.1571)²
Solving for rA, we get:
rA = 23.15 meters
23.15/rB = 5.05
Solving for rB, we get:
rB = 4.58 meters
a = rBω²
Substituting the values we just found, we get:
a = (4.58)(0.1571)²
Solving for a, we get:
a = 0.11 m/s²
To know more about acceleration visit:-
https://brainly.com/question/12550364
#SPJ9
Which of the following is the formula for Electric Charge?
The formula for Electric Charge is (Q = I ∙ t) I is the electric current and t is time
What is Electric Charge?Electric charge is a fundamental property of matter that describes the amount of electric force that a particle can exert on other charged particles. It is a property of particles, such as electrons and protons, that gives rise to the electromagnetic force, which is one of the four fundamental forces in nature.
Electric charge can be positive or negative, and particles with the same charge repel each other, while particles with opposite charges attract each other. The unit of electric charge is the Coulomb (C), and it is measured using an instrument called an electrometer.
Learn more about Electric Charge at:
https://brainly.com/question/2373424
#SPJ1
a scientist on earth drops a hammer and a feather at the same time an astronaut on the moon drops a hammer and a feather. which result is expected?
The answer depends if air resistance is ignored. If ignored, the feather and hammer on moon and earth will reach the ground at the same time with respect to their gravitational force (earth > moon)
If air resistance is not ignored, the hammer will reach the ground first on both earth and moon
When a scientist on Earth drops a hammer and a feather at the same time, the expected result is that the hammer would hit the ground first.
When an astronaut on the moon drops a hammer and a feather at the same time, they would hit the ground at the same time. This is because the gravitational pull on the moon is weaker than that on Earth, so objects fall at the same rate regardless of their mass.
What is gravity?Gravity is the force that exists between any two masses, any two bodies, any two particles. It is an attraction force that always exists between objects, and the magnitude of the force depends on the masses of the objects and the distance between them. On the surface of the earth, gravity acts to pull all objects towards the center of the earth, resulting in weight of objects on the surface of the earth.
What is free fall?Free fall refers to the motion of an object falling under the influence of gravity. When an object is dropped from a certain height, it will fall at an accelerating rate towards the ground, until it hits the ground. Objects fall at the same rate regardless of their mass.
To know more about gravitational pull, refer here:
https://brainly.com/question/13467280#
#SPJ11
a person is on a motoboat that is capable of a maximum speed of 10 km/h in still water, and wishes to cross a 2 km wide river to a point directly across from the starting point. if the speed of the water in the river is 6 km/h, how much time is required for the crossing, assuming the boat is moving at its maximum speed?
An individual on a motorboat with a top speed of 10 km/h wants to travel across a 2 km wide river to a location that is exactly opposite the beginning spot. The time required for crossing the river is approximately 12.4 minutes.
To calculate the time required for crossing the river, we can use the formula:
time = distance/speed
Let's call the speed of the boat in still water "v" and the speed of the river "u". The boat is moving at its maximum speed in still water, so its speed relative to the shore is also "v" km/h.
Now, to cross the river, the boat must move at an angle to the shore to compensate for the sideways drift caused by the river current. We can use trigonometry to determine the composition of the boat's speed in the direction perpendicular to the river, which is the distance that the boat covers while crossing the river.
The component of the boat's speed perpendicular to the river is given by:
v_perp = v * sin(theta)
where theta is the angle between the boat's path and the direction of the current, and sin(theta) is the sine of this angle.
Since the boat is moving at its maximum speed, v = 10 km/h, and the speed of the river is u = 6 km/h, we can use trigonometry to find the angle theta:
sin(theta) = u / v = 6 / 10 = 0.6
theta = sin^-1(0.6) = 36.87 degrees
Now we can find the distance that the boat covers while crossing the river:
distance = 2 km * sin(theta) = 1.2 km
The time required to cover this distance at the boat's maximum speed is:
time = distance / v_perp = 1.2 km / (10 km/h * sin(36.87)) = 0.206 hours
To learn more about top speed
https://brainly.com/question/7010490
#SPJ4
while attempting to remove a stubborn lug nut from a wheel on your project car, you apply a force on the end of a long wrench with length 18.5 cm, such that your arm and the wrench form a 90 degree angle. the lug nut isn't budging, so you start to push harder until it finally comes loose when you push with 212 n of force. how much torque was required to loosen the lug nut?
The torque required to loosen the lug nut was approximately 39.22 Newton-meters.
The torque required to loosen the lug nut can be calculated as follows.Torque = Force x Distance
To calculate the torque required to loosen the lug nut, we need to calculate the distance between the point of application of force and the axis of rotation of the nut. This distance is the effective length of the wrench, which is the length of the wrench multiplied by the sine of the angle between the wrench and the force applied.
So we have:Effective length of wrench = 18.5 cm x sin 90°
Effective length of wrench = 18.5 cm
The torque required to loosen the lug nut is:T = F × D
Effective torque = 212 N × 0.185 m
Effective torque = 39.22 Nm
Therefore, the torque required to loosen the lug nut is 39.22 Nm.
More on torque: https://brainly.com/question/10122447
#SPJ11
the period of a mass-spring oscillator is 2.76 s. every time the oscillator completes a full period, the amplitude of the oscillation gets reduced to 91.7 percent of the previous amplitude. how much time does it take for the amplitude to decay to 44.5 percent of its original initial value?
The required time taken to decay 44.5% is calculated to be 25.80 s.
It is given that the period of mass-spring oscillator is 2.76 s.
Amplitude is said to reduce by 91.7%.
Algorithmic decrement is given by,
a₁ = a₀ e^(-bt)
where,
b is constant
a₁ = 0.917 a₀
0.917 a₀ = a₀ e^(-b× 2.76)
e^(-b× 2.76) = 0.917
-b× 2.76 = log(0.917)
-b× 2.76 = -0.086
2.76 b = 0.086
b = 0.031
a₁ = a₀ (0.445)
a₀ (0.445) = a₀ e^(0.031 t)
e^(0.031 t) = (0.445)
0.031 t = log(0.445)
0.031 t = 0.8
t = 25.80 s
Thus, the time taken to decay 44.5% is 25.80 s.
To know more about springs:
https://brainly.com/question/29762267
#SPJ4
a spring requires 5 j to stretch the spring from 8 cm to 12 cm, and an additional 4 j to stretch the spring from 12 cm to 14 cm. what is the natural length of the spring?
The natural length of the spring is 8 cm.
We can use the formula for the potential energy stored in a spring:
U = (1/2)kx^2
where U is the potential energy, k is the spring constant, and x is the displacement from the spring's natural length.
Let's first find the spring constant, k:
U = (1/2)kx^2
5 J = (1/2)k(0.04 m)^2
k = (2*5 J) / (0.04 m)^2
k = 625 N/m
Now, we can find the natural length of the spring, x0:
U = (1/2)kx^2
9 J = (1/2)(625 N/m)(x - 0.08 m)^2 (using x-0.08m since it has stretched 8cm)
4 J = (1/2)(625 N/m)(x - 0.12 m)^2 (using x-0.12m since it has stretched 12cm from natural length)
We have two equations and two unknowns (x and x0), so we can solve for x0:
9 J = (1/2)(625 N/m)(x - 0.08 m)^2
36 = (x - 0.08 m)^2
x = 2.0 x 0.08 m - 0.12 m or x= 0.04m or x=0.16m
Now we can check which one of these solutions makes sense based on the second equation:
4 J = (1/2)(625 N/m)(x - 0.12 m)^2
4 J = (1/2)(625 N/m)(0.04 m)^2 or 4 J = (1/2)(625 N/m)(0.16 m)^2
So we see that x = 0.16m is not a valid solution, as it would require more energy to stretch the spring from 12cm to 14cm than we have. Therefore, the natural length of the spring is:
x0 = 0.08 m.
So, the natural length of the spring is 8 cm.
For more such questions on length , Visit:
https://brainly.com/question/29813582
#SPJ11
moment of inertia of an object does not depend on a. angular velocity b. mass distribution
Answer:
Explanation:
The moment of inertia of an object is a property that describes its resistance to rotational motion.
It is determined solely by the mass distribution of the object and the geometry of its shape, and it does not depend on the angular velocity of the object.
This can be seen from the formula for the moment of inertia, which is given by:I = ∫ r^2 dmwhere I is the moment of inertia, r is the distance from the axis of rotation to the mass element dm, and the integral is taken over the entire mass distribution of the object.
The moment of inertia depends only on the mass distribution of the object and how that mass is distributed around the axis of rotation.
This means that even if the object is rotating at different speeds or in different directions, its moment of inertia will remain the same, as long as the mass distribution is unchanged.