The ratio [CH3CO2H]/[CH3CO2-] in the buffer solution is approximately 2.70 x 10^-3, or you can also write it as 1:370.
To calculate the ratio of the concentration of acetic acid (CH3CO2H) to sodium acetate (CH3CO2-) in the buffer solution, we can use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
Where:
pH is the given pH of the buffer solution, which is 5.05.
pKa is the negative logarithm of the acid dissociation constant, Ka, which is given as 1.80 x 10^-5 for acetic acid (CH3CO2H).
[A-] is the concentration of the conjugate base (CH3CO2-), which is the sodium acetate.
[HA] is the concentration of the acid (CH3CO2H), which is the acetic acid.
Let's plug in the values into the equation and solve for the ratio [HA]/[A-].
5.05 = -log(1.80 x 10^-5) + log([A-]/[HA])
Next, rearrange the equation to solve for the ratio [A-]/[HA]:
log([A-]/[HA]) = 5.05 + log(1.80 x 10^-5)
Now, we need to convert the logarithmic expression back into exponential form:
[A-]/[HA] = 10^(5.05 + log(1.80 x 10^-5))
Simplifying the right side of the equation:
[A-]/[HA] = 10^5.05 * 10^(log(1.80 x 10^-5))
Using the property of logarithms (log(a) + log(b) = log(ab)):
[A-]/[HA] = 10^5.05 * 1.80 x 10^-5
[A-]/[HA] = 150 * 1.80 x 10^-5
[A-]/[HA] = 2.70 x 10^-3
Therefore, the ratio [CH3CO2H]/[CH3CO2-] in the buffer solution is approximately 2.70 x 10^-3, or you can also write it as 1:370.
Learn more about buffer solution on :
https://brainly.com/question/8676275
#SPJ11
The ratio of the concentration of CH₃CO₂H to CH₃CO₂⁻ in the buffer is approximately 2.03.
The ratio of the concentration of acetic acid (CH₃CO₂H) to sodium acetate (CH₃CO₂⁻) in the buffer can be determined using the Henderson-Hasselbalch equation:
pH = pKa + log ([A-]/[HA])
In this case, acetic acid (CH₃CO₂H) is the weak acid (HA) and sodium acetate (CH₃CO₂⁻) is the conjugate base (A-).
First, let's calculate pKa using the Ka value given:
pKa = -log(Ka)
= -log(1.80 x 10^-5)
= 4.74
Now, we can rearrange the Henderson-Hasselbalch equation to solve for the ratio of [CH₃CO₂H] to [CH₃CO₂⁻]:
pH - pKa = log ([CH₃CO₂⁻]/[CH₃CO₂H])
Since the pH is given as 5.05 and pKa is 4.74, we can substitute these values:
5.05 - 4.74 = log ([CH₃CO₂⁻]/[CH₃CO₂H])
0.31 = log ([CH₃CO₂⁻]/[CH₃CO₂H])
To find the actual ratio, we need to convert the logarithm in the exponential form:
10^0.31 = [CH₃CO₂⁻]/[CH₃CO₂H]
2.03 = [CH₃CO₂⁻]/[CH₃CO₂H]
Therefore, the ratio of the concentration of CH₃CO₂H to CH₃CO₂⁻ in the buffer is approximately 2.03.
Learn More About " Acetic acid" from the link:
https://brainly.com/question/15231908
#SPJ11
Part 2: Compressors Q5: List types of compressors. Q6: What type of compressors used in the company? Q7: List the location where compressors are used and for what they are used. Q8: At what pressures
The types of compressors include Reciprocating compressors , Rotary screw compressors, Centrifugal compressors, Axial compressors.
1. Reciprocating compressors these compressors use a piston-cylinder mechanism to compress gas or air. They are commonly used in small-scale applications like refrigeration systems and air compressors.
2. Rotary screw compressors these compressors use two rotating screws to compress gas or air. They are widely used in industries like manufacturing, construction, and oil and gas.
3. Centrifugal compressor these compressors use a high-speed impeller to accelerate the gas or air, which is then converted into pressure. They are often used in large-scale applications like power plants and chemical industries.
4. Axial compressors these compressors use a series of rotating blades to compress gas or air in a linear direction. They are typically used in aerospace applications, such as jet engines.
The type of compressors used in a company can vary depending on the specific needs and requirements of the company. Some common types of compressors used in companies include reciprocating compressors, rotary screw compressors, and centrifugal compressors.
Compressors are used in various locations for different purposes. Here are some examples:
- In industrial plants compressors are used to supply compressed air for operating pneumatic tools, controlling valves, and driving processes such as spray painting and cleaning.
- HVAC systems compressors are used in air conditioning and refrigeration systems to compress and circulate refrigerant, enabling the cooling or heating of spaces.
- Gas pipelines compressors are used to compress natural gas or other gases, allowing them to be transported through pipelines over long distances.
- Power plants compressors are used to compress air for combustion in gas turbines, enhancing power generation efficiency.
The pressure at which compressors operate can vary depending on the specific application and requirements. It can range from a few pounds per square inch (psi) to several thousand psi. For example, in air compressors used for powering pneumatic tools, the pressure may typically be around 90-150 psi.
It's important to note that the exact pressures used in a specific company or application will depend on factors such as the type of compressor, the intended use, and the system requirements.
Learn more about compressors with the given link,
https://brainly.com/question/30404542
#SPJ11
2 req re. %) 2 req When a 16.0 mL sample of a 0.320 M aqueous nitrous acid solution is titrated with a 0.494 M aqueous sodium hydroxide solution, what is the pH at the midpoint in the titration? pH =
The pH at the midpoint of the titration between Nitrous Acid and Sodium Hydroxide is 1.017.
We use the concept of the Half-Equivalence Point of titration, to solve this problem and obtain the pH.
The Half-Equivalence point marks that part of a reaction where one of the reactants is half-used. It is also a designated midpoint of the reaction.
So, first, we try and find the number of moles of Nitrous Acid, HNO₂ present in the reaction.
We have been given that 16.0 mL of 0.320M acid solution was used for titration.
So, using the Formula for Molarity,
Molarity = (No. of moles of solute)/(Volume of Solution in L)
No. of moles = Molarity * Volume of Solution in L
We substitute the known values in this.
No. of Moles of HNO₂ = 0.320M * 0.016L
= 0.00512 mol
As mentioned before, half of the moles of reactant would have reacted.
So, No. of Moles of HNO₂ reacted = 0.00512/2 = 0.00256 moles reacted.
Since the ratio of stoichiometric coefficients of both the reactants is 1 : 1 in their reaction, we can safely say the same number of moles would have reacted.
So, No. of moles of NaOH reacted by midpoint would also be 0.00256 mol.
We also get the volume of NaOH used in the titration.
Volume in L = No. of Moles/Molarity
= 0.00512/0.494
= 0.0104L
Now, moving to the mid-point, the total volume of the solution is the sum of the volumes of both its components.
Total Volume = 0.0104 + 0.016
= 0.0264L
The concentration of the acid, or H⁺ ions at the midpoint will be:
Concentration = No. of moles at mid-point/Total Volume
= 0.00256/0.0264
= 0.096M
Finally, as we have the concentration of H⁺ ions in the midpoint solution, we apply the formula for pH.
pH = -Log[H⁺]
= -Log[0.096]
= -(-1.017)
= 1.017
Thus, the pH at the midpoint of the titration will be approximately 1.017.
For on Midpoint of Titration,
brainly.com/question/32745455
#SPJ4
Express
(
x
+
3
)
2
(x+3)
2
as a trinomial in standard form
The trinomial in standard form that represents (x + 3)^2 is x^2 + 6x + 9.
To express the expression (x + 3)^2 as a trinomial in standard form, we need to expand the expression. The process of expanding involves multiplying the terms in the expression using the distributive property.
(x + 3)^2 can be expanded as follows:
(x + 3)(x + 3)
Using the distributive property, we multiply the terms inside the parentheses:
x(x) + x(3) + 3(x) + 3(3)
Simplifying each term, we get:
x^2 + 3x + 3x + 9
Combining like terms, we have:
x^2 + 6x + 9
Consequently, x2 + 6x + 9 is the trinomial in standard form that represents (x + 3)2.
In general, to expand a binomial squared, we multiply each term in the first binomial by each term in the second binomial, and then combine like terms. The result is a trinomial in standard form, which consists of three terms with the highest degree term appearing first, followed by the middle degree term, and finally the constant term.
for such more question on standard form
https://brainly.com/question/14820864
#SPJ8
9. A fatigue test is done with a stress amplitude of 20MPa and an average stress of 60MPa. Which of the statements below is/are correct? Correct where necessary. a. σ₁-20MPa en om=60MPa b. Gmax=80MPa en R=Gmin/max =0.33 c. Ao=40MPa en R=Gmin/max =0.5 d. Omax=80MPa en Omin=40MPa 9. All are correct except b: incorrect, R = 0.5
The correct option is C. According to the given statement The stress ratio as, 40/80= 0.5.
A fatigue test is done with a stress amplitude of 20MPa and an average stress of 60MPa.
The formula for the stress ratio R is,
R = σmin/σmax
We have given that the stress amplitude of the fatigue test is 20MPa and the average stress is 60MPa.
Therefore, the maximum stress will be equal to the stress amplitude plus the average stress.
Omax = σm + σa= 60 + 20= 80 Mpa
The minimum stress will be the difference between the average stress and the stress amplitude.
Omin = σm - σa= 60 - 20= 40 Mpa
Now we can calculate the stress ratio as,
R = σmin/σmax= 40/80= 0.5
Therefore, option c is the correct.
To know more about amplitude visit:
https://brainly.com/question/31013469
#SPJ11
For the following molecules: CCl_4, CHCl_3, CS_2 Which of them has/have a permenant dipole? (a) Only CCl_4 has permenant dipole, CHCl_3and CS_2 are not polar overall. (b) Only CHCl_3 has permenant dipole, CCl_and CS_2are not polar overall. (c) Only CS_2 has permenant dipole, CCl4 and CHCl_3 are not polar overall. (d) None of the above is correct.
Only CHCl3 has a permanent dipole, CCl4 and CS2 are not polar overall. The permanent dipole is the uneven distribution of electron density in a molecule arising from the covalent bond between two atoms with different electronegativities.
The correct answer is option B.
It creates a partial charge separation in the molecule, making it a polar molecule. Tetrachloromethane (CCl4) is also known as carbon tetrachloride. In the center of the molecule, there is a carbon atom with four chlorine atoms positioned symmetrically around it. Since the chlorine atoms are equally distributed around the carbon atom, they all pull electrons away from the carbon atom equally, making CCl4 a nonpolar molecule.
Chloroform is another name for CHCl3. CHCl3 has a tetrahedral shape, with the carbon atom at the center and the three hydrogen atoms and one chlorine atom located at the tetrahedron's vertices. CHCl3 is a polar molecule since the electronegativity of chlorine is greater than that of hydrogen. Carbon disulfide (CS2) is a colorless and odorless organic compound made up of carbon and sulfur atoms. It is a nonpolar molecule since the electronegativity difference between carbon and sulfur is minimal, making the bond between them nonpolar.Hence, (b) Only CHCl3 has a permanent dipole, CCl4 and CS2 are not polar overall.
To know more about distribution visit:
https://brainly.com/question/16029306
#SPJ11
Determine the pH and percent ionization for a hydrocyanic acid (HCN) solution of concentration 5.5×10^−3M. ( Ka
for HCN is 4.9×10^−10) pH=
(Enter your answer in scientific notation.)
pH = 5.28; Percent ionization = 0.0945%.
To determine the pH and percent ionization for a hydrocyanic acid (HCN) solution of concentration 5.5×10−3 M, we are given that the value of Ka for HCN is 4.9×10−10. We can use the formula of Ka to find the pH and percent ionization of the given hydrocyanic acid solution.
[tex]Ka = [H3O+][CN-]/[HCN][/tex]
[tex]Ka = [H3O+]^2/[HCN][/tex]
Since the concentration of CN- is equal to the concentration of H3O+ because one H+ ion is donated by HCN, we can take [H3O+] = [CN-]
[tex]Ka = [CN-][H3O+]/[HCN][/tex]
Substituting the values given in the question
[tex]Ka = x^2/[HCN][/tex]
where x is the concentration of H3O+ ions when the equilibrium is established.
Let the concentration of H3O+ be x. Thus, [CN-] = x
[[tex]Moles of HCN] = 5.5×10^-3 M[/tex]
Volume of the solution is not given. However, it is safe to assume that the volume is 1 L since it is not mentioned otherwise.
Number of moles of HCN in 1 L of solution = [tex]5.5×10^-3 M × 1 L = 5.5×10^-3 moles[/tex]
Now,
[tex]Ka = x^2/[HCN][/tex]
[tex]4.9×10^-10 = x^2/5.5×10^-3[/tex]
[tex]x^2 = 4.9×10^-10 × 5.5×10^-3[/tex]
[tex]x^2 = 2.695×10^-12[/tex]
[tex]x = [H3O+] = √(2.695×10^-12) = 5.2×10^-6[/tex]
[tex]pH = -log[H3O+][/tex]
[tex]pH = -log(5.2×10^-6)[/tex]
pH = 5.28
Percent ionization = [H3O+]/[HCN] × 100
[H3O+] = 5.2×10^-6, [HCN] = 5.5×10^-3
Percent ionization =[tex](5.2×10^-6/5.5×10^-3) × 100[/tex]
Percent ionization = 0.0945%
Answer: pH = 5.28; Percent ionization = 0.0945%.
Know more about percent ionization
https://brainly.com/question/1619653
#SPJ11
The pH of a hydrocyanic acid (HCN) solution with a concentration of 5.5×10^−3 M can be calculated to be approximately 2.06. The percent ionization of the HCN solution can be determined using the Ka value of 4.9×10^−10.
To calculate the pH of the HCN solution, we first need to determine the concentration of H+ ions in the solution. Since hydrocyanic acid (HCN) is a weak acid, it will undergo partial ionization in water. The concentration of H+ ions can be obtained by calculating the square root of the Ka value multiplied by the initial concentration of HCN.
[H+] = sqrt(Ka * [HCN])
[H+] = sqrt(4.9×10^−10 * 5.5×10^−3)
[H+] ≈ 2.35×10^−7 M
Using the concentration of H+ ions, we can calculate the pH of the solution by taking the negative logarithm (base 10) of the H+ ion concentration:
pH = -log[H+]
pH ≈ -log(2.35×10^−7)
pH ≈ 2.06
The percent ionization of the HCN solution can be determined by dividing the concentration of ionized H+ ions ([H+]) by the initial concentration of HCN and multiplying by 100:
Percent Ionization = ([H+] / [HCN]) * 100
Percent Ionization = (2.35×10^−7 / 5.5×10^−3) * 100
Percent Ionization ≈ 0.00427%
Therefore, the pH of the HCN solution is approximately 2.06, and the percent ionization is approximately 0.00427%.
To calculate the pH of the HCN solution, we first need to determine the concentration of H+ ions in the solution. Since hydrocyanic acid (HCN) is a weak acid, it will undergo partial ionization in water. The concentration of H+ ions can be obtained by calculating the square root of the Ka value multiplied by the initial concentration of HCN.
[H+] = sqrt(Ka * [HCN])
[H+] = sqrt(4.9×10^−10 * 5.5×10^−3)
[H+] ≈ 2.35×10^−7 M
Using the concentration of H+ ions, we can calculate the pH of the solution by taking the negative logarithm (base 10) of the H+ ion concentration:
pH = -log[H+]
pH ≈ -log(2.35×10^−7)
pH ≈ 2.06
The percent ionization of the HCN solution can be determined by dividing the concentration of ionized H+ ions ([H+]) by the initial concentration of HCN and multiplying by 100:
Percent Ionization = ([H+] / [HCN]) * 100
Percent Ionization = (2.35×10^−7 / 5.5×10^−3) * 100
Percent Ionization ≈ 0.00427%
Therefore, the pH of the HCN solution is approximately 2.06, and the percent ionization is approximately 0.00427%.
Know more about solution:
brainly.com/question/1619653
#SPJ11
Water is a rather interesting material because its density as a liquid is greater than its density as a solid. Hence, water has a negative slope for the equilibrium line between solid and liquid. Which of the following statement below must be true? a. Samples of water is always lighter than samples of ice. b. When compressed under high pressure, water is more likely to assume the solid phase. c. Clapeyron equation outcome for water is negative. d. The phase transition of water must be described using Helmholtz free energy and not Gibbs free energy.
The statement that must be true is d. The phase transition of water must be described using Helmholtz free energy and not Gibbs free energy.
Water is unique in that its density as a liquid is higher than its density as a solid. This behavior is a result of the hydrogen bonding between water molecules. When water freezes, the hydrogen bonds arrange themselves in a crystal lattice, creating a network with empty space between the molecules. This leads to the expansion of water upon freezing, resulting in ice having a lower density than liquid water.
This phenomenon also affects the equilibrium line between the solid and liquid phases of water. The slope of this line is negative, indicating that as pressure increases, the melting point of water decreases. This means that under high pressure, water is more likely to assume the solid phase.
Regarding the options, statement a is incorrect because the density of ice is lower than that of water, making samples of ice lighter than samples of water. Statement b is correct based on the explanation above. Statement c is not necessarily true as the Clapeyron equation relates the phase transition temperature and enthalpy change, but does not directly indicate the sign of the outcome.
Statement d is true because the phase transition of water is best described using the Helmholtz free energy, which incorporates both temperature and volume effects, rather than the Gibbs free energy.
In summary, the phase transition of water, with its unique density behavior, is best described using the Helmholtz free energy rather than the Gibbs free energy.
Learn more about Helmholtz
brainly.com/question/15566237
#SPJ11
A fruit seller bought some watermelons at GH¢5.00 each only to realize that 12 were rotten. She then sold the rest at GH¢7.00 and made a profit of GH¢150.00. how many watermelons did she buy?
The seller bought 117 watermelons in all.
Let the total number of watermelons that the seller bought be x. The cost price of each watermelon is GH¢5.00. Thus, the cost of x watermelons is 5x. The seller realizes that 12 of these are rotten and cannot be sold.
The number of good watermelons left with the seller is (x - 12). She decides to sell these watermelons at GH¢7.00 each.The total profit made by the seller is GH¢150.00.
We know that profit is given by:
Profit = Selling price - Cost price
The selling price of the good watermelons is GH¢7.00 per watermelon. Thus, the total selling price is (x - 12) × 7. Therefore, we can write:Profit = Selling price - Cost price150 = (x - 12) × 7 - 5x150 = 7x - 84 - 5x150 + 84 = 2x × 234 = 2x
Therefore, the total number of watermelons bought by the seller is x = 117. Thus, the seller bought 117 watermelons in all.
For more such questions on watermelons, click on:
https://brainly.com/question/1246496
#SPJ8
A rural township in central Arkansas has recently replaced several septic tanks that have an anticipated life span of 24 years. Today, these septic tanks cost $24,000. However, they received a grant from the Environmental Protection Agency that matched the cost of the tanks today in order for the tanks to be replaced after their end of life. Assuming an interest rate of 7.5%, how much will a complete replacement of the septic tanks cost in 20 years?
The total cost for a complete replacement of the septic tanks in 20 years is $75,509.70 (approx).
Given that a rural township in central Arkansas has replaced several septic tanks that have an anticipated life span of 24 years for $24,000. Also, they received a grant from the Environmental Protection Agency that matched the cost of the tanks today in order for the tanks to be replaced after their end of life.
Let’s determine the future value of $24,000 at the end of 20 years, where the interest rate is 7.5%.
We will use the formula;
FV = PV × [1 + (i / n)]^(n × t)
Where,
FV = Future Value
PV = Present Value
i = interest rate
t = time in years
n = number of compounding periods per year
The present value of septic tanks, PV = $24,000
The interest rate, i = 7.5%
The time period, t = 20 years
The number of compounding periods per year, n = 1
Substitute the given values in the formula;
FV = 24000 × [1 + (7.5 / 100) ]^(1 × 20)\
FV = 24000 × [1.075 ]^20
FV = $75,509.70
Answer: $75,509.70
To know more about the total cost, visit:
https://brainly.com/question/28715238
#SPJ11
What is the difference between grade 60 (Gr-60) and grade 80 (Gr-80) steel rebar?
The main difference between grade 60 (Gr-60) and grade 80 (Gr-80) steel rebar lies in their tensile strength. Tensile strength refers to the maximum amount of tensile stress that a material can withstand without breaking. In this case, it indicates the maximum force or load that the steel rebar can bear before fracturing.
1. Grade 60 (Gr-60) steel rebar has a minimum tensile strength of 60,000 pounds per square inch (psi). This means that it can withstand a greater amount of force or load compared to lower grade rebar, such as grade 40 or grade 50. Grade 60 rebar is commonly used in construction projects that require moderate strength.
2. Grade 80 (Gr-80) steel rebar, on the other hand, has a minimum tensile strength of 80,000 psi. This higher tensile strength makes it stronger and more resistant to deformation under high-stress conditions. Grade 80 rebar is typically used in applications that require higher strength, such as in bridges, heavy-duty structures, and seismic-resistant structures.
To put it simply, grade 80 steel rebar is stronger and can withstand higher loads or forces compared to grade 60 rebar. The choice between the two grades depends on the specific requirements and design considerations of the construction project. It is important to consult engineering specifications and codes to determine the appropriate grade of steel rebar to be used in a particular application.
Overall, the difference between grade 60 (Gr-60) and grade 80 (Gr-80) steel rebar lies in their tensile strength, with grade 80 rebar having a higher tensile strength and therefore being able to withstand greater forces or loads.
Learn more about steel rebar:
https://brainly.com/question/31317127
#SPJ11
1. Using Laplace Transform, solve a differential
equation with polynomial coefficients. Explain
The Laplace transform is a valuable tool for solving differential equations with polynomial coefficients. By applying the transform, we can convert the differential equation into an algebraic equation in the Laplace domain, simplifying the problem. The transformed equation is then solved algebraically, and the inverse Laplace transform is used to obtain the solution in the time domain.
The Laplace transform is a powerful mathematical tool used to solve differential equations by transforming them into algebraic equations. By applying the Laplace transform to a differential equation with polynomial coefficients, we can simplify the problem and solve it using algebraic operations.
To illustrate this, let's consider a linear ordinary differential equation with polynomial coefficients of the form:
a_ny^n + a_(n-1)y^(n-1) + ... + a_1y' + a_0y = f(t),
where y represents the dependent variable, t is the independent variable, and f(t) is a known function. The Laplace transform of this equation is obtained by applying the Laplace transform to both sides of the equation, resulting in:
L[a_ny^n] + L[a_(n-1)y^(n-1)] + ... + L[a_1y'] + L[a_0y] = L[f(t)],
where L[.] denotes the Laplace transform operator.
Using the properties of the Laplace transform and its table of transforms, we can determine the transformed form of each term. The transformed equation becomes:
a_nY^n(s) + a_(n-1)Y^(n-1)(s) + ... + a_1sY(s) + a_0Y(s) = F(s),
where Y(s) and F(s) represent the Laplace transforms of y(t) and f(t) respectively, and s is the complex variable.
Now, we have an algebraic equation in the Laplace domain, which can be solved to obtain the expression for Y(s). Finally, by applying the inverse Laplace transform, we can obtain the solution y(t) in the time domain.
In conclusion, by using the Laplace transform, we can convert a differential equation with polynomial coefficients into an algebraic equation in the Laplace domain. Solving this algebraic equation provides us with the transformed solution, which can be inverted back to the time domain using the inverse Laplace transform, giving us the final solution to the original differential equation.
Learn more about Laplace transform https://brainly.com/question/29583725
#SPJ11
The most common crystallisation strategies in pharmaceutical purification are cooling crystallisation, evaporation crystallisation, anti-solvent crystallisation, or their combinations. Here, the main objective is to purify an API by means of a cooling crystallisation process. Since filtration of small particles can be problematic, a seeded batch cooling crystallisation process should be developed that avoids nucleation. a) First, consider a general crystallizer: i) Write the unsteady state population balance that describes the process, commenting on the physical meaning of each term appearing in your equations. ii) Write the population balance under steady state conditions.
The unsteady state population balance can be used to describe the cooling crystallisation process. This equation is used to describe the dynamic changes in crystal population during the process.
The seeded batch cooling crystallization process is considered the best option for the purification of an API. The following is the detailed explanation of a general crystallizer with unsteady and steady-state population balances and their meaning: Unsteady-state population balance: The unsteady-state population balance for a general crystallizer can be written as: dN/dt = G - R Here, dN/dt = Rate of accumulation of crystals in the crystallizer, , G = Generation rate of crystals due to nucleation, R = Rate of removal of crystals due to growth. The physical meaning of each term appearing in the equation: G: The generation rate of crystals (i.e., the rate of appearance of new crystals) is related to nucleation. R: The rate of removal of crystals (i.e., the rate at which the existing crystals disappear) is related to growth. dN/dt: The rate of accumulation of crystals is related to the difference between the generation and removal rates. Steady-state population balance: The steady-state population balance for a general crystallizer can be written as:G = R, Here, G = Generation rate of crystals due to nucleation R = Rate of removal of crystals due to growth. The population balance under steady-state conditions describes a process that has reached equilibrium and is in a state of balance between the rates of generation and removal. When the rate of nucleation equals the rate of growth, the system has reached steady-state, and the generation rate equals the removal rate.
Therefore, the unsteady-state population balance for a general crystallizer can be written as dN/dt = G - R, while the steady-state population balance for a general crystallizer can be written as G = R.
learn more about crystallisation visit:
brainly.com/question/31058900
#SPJ11
a 9. What technology does a total station use to measure distance? Include why D = vt is not a practical solution method for this technology
Therefore, total stations use more complex algorithms to calculate distances and account for these factors.
A total station is a device used in surveying and civil engineering that uses electronic transit theodolites, electronic distance meters (EDM), and microprocessors to calculate coordinates based on measured horizontal angles, vertical angles, and distances.
Total stations use EDM to measure distances, and this is done by sending out a laser beam and measuring the time it takes for it to return after reflecting off an object. The device then uses this time measurement and the speed of light to calculate the distance between the total station and the object in question.
D = vt is not a practical solution method for this technology because it assumes that the speed of light is constant in all mediums. In reality, the speed of light varies in different mediums, such as air and water, and this can lead to errors in distance measurement.
Additionally, D = vt assumes that the laser beam is always traveling in a straight line, which is not always the case in the real world due to atmospheric refraction and other factors.
Know more about the electronic distance meters (EDM)
https://brainly.com/question/15452991
#SPJ11
Find The volume of a road construction marker, A cone with height 3 feet and base radius 1/4 feet. Use 3.14 as an approximation for The volume of the cone is _____
The volume of the road construction marker (a cone with height 3 feet and base radius 1/4 feet) is approximately equal to 0.19625 cubic feet.
Given that the cone with height 3 feet and base radius 1/4 feet.
To find the volume of the road construction marker, we need to use the formula for the volume of a cone.
Volume of a cone = 1/3 πr²h
Where, r is the radius of the cone and h is the height of the cone.
Substituting the given values in the above formula,
Volume of cone = 1/3 × 3.14 × (1/4)² × 3= 1/3 × 3.14 × 1/16 × 3= 3.14/16= 0.19625 cubic feet
Hence, the volume of the road construction marker (a cone with height 3 feet and base radius 1/4 feet) is approximately equal to 0.19625 cubic feet.
Learn more about volume
https://brainly.com/question/28058531
#SPJ11
Coal with the following composition: total carbon 72 %; volatile matter 18 %, fixed carbon 60 %; free water 5 %, was combusted in a small furnace with dry air. The flowrate of the air is 50 kg/h. 5% carbon leaves the furnace as uncombusted carbon. The coal contains no nitrogen, nor sulphur. The exhaust gas Orsat analysis has the following reading CO2 12.8 %; CO = 1.2%; 02 = 5.4 %6. In addition to the flue gas, a solid residue comprising of unreacted carbon and ash leaves the furnace. a. Submit a labeled block flow diagram of the process. b. What is the percentage of nitrogen (N2) in the Orsat analysis? c. What is the percentage of ash in the coal? d. What is the flowrate (in kg/h) of carbon in the solid residue? e. What is the percentage of the carbon in the residue? f. How much of the carbon in the coal reacts (in kg/h)? g. What is the molar flowrate (in kmol/h) of the dry exhaust gas? How much air (kmol/h) is fed?
a) The Block flow diagram is given below. b) Percentage of nitrogen is 70.6%. c) Percentage of ash is 9%. d) Flowrate is 2.5 kg/h. e) Percentage of the carbon is 83.33%. f) The amount of carbon is 47.5 kg/h. g) Molar flowrate is 0.49 kmol/h, amount is 21.74 kmol/h.
a. Block flow diagram
Coal
+
Air
=
Flue gas
+
Residue
b. Percentage of nitrogen (N2) in the Orsat analysis
The percentage of nitrogen in the Orsat analysis is 100 - (12.8 + 1.2 + 5.4) = 70.6%.
c. Percentage of ash in the coal
The percentage of ash in the coal is 100 - (72 + 18 + 60 - 5) = 9%.
d. Flowrate (in kg/h) of carbon in the solid residue
The flowrate of carbon in the solid residue is 0.05 * 50 kg/h = 2.5 kg/h.
e. Percentage of the carbon in the residue
The percentage of carbon in the residue is 2.5 kg/h / (2.5 + 0.5) kg/h * 100% = 83.33%.
f. How much of the carbon in the coal reacts (in kg/h)
The amount of carbon in the coal that reacts is 50 kg/h - 2.5 kg/h = 47.5 kg/h.
g. Molar flowrate (in kmol/h) of the dry exhaust gas
The molar flowrate of the dry exhaust gas is 0.128 * 50 kg/h / 12.01 kg/kmol = 0.49 kmol/h.
The amount of air fed is 50 kg/h / 0.23 kg/kmol = 21.74 kmol/h.
To learn more about Percentage here:
https://brainly.com/question/14801224
#SPJ4
Suppose X is a continuous uniform random variable with μ=5 and σ=20✓3. Find
a) the p.d.f of X, b) the c.d.f. of X.
a) The probability density function (p.d.f) of X is a constant function defined as f(x) = 1/40√3, for 0 ≤ x ≤ 40√3.
b) The cumulative distribution function (c.d.f) of X is given by F(x) = (x-0)/(40√3), for 0 ≤ x ≤ 40√3.
a) The p.d.f of a continuous uniform random variable is a constant function over a specified range. In this case, the range is from 0 to 40√3. Since X is a continuous uniform random variable with a mean (μ) of 5 and a standard deviation (σ) of 20√3, we can determine that the range of the random variable is twice the standard deviation, which is 40√3. The p.d.f is defined as the reciprocal of the range, which gives us f(x) = 1/40√3 for 0 ≤ x ≤ 40√3.
b) The c.d.f of a continuous uniform random variable is the probability that the random variable is less than or equal to a given value. For X, the c.d.f is a linear function that starts at 0 and increases with a slope equal to 1 divided by the range. In this case, the range is 40√3, so the c.d.f is given by F(x) = (x-0)/(40√3) for 0 ≤ x ≤ 40√3.
Learn more about probability density function (p.d.f)
#SPJ11
3. Use the data provided in the table to answer the questions. Assume that these four conditions/diseases are the only ones that anyone ever gets. (10 pts) a. What is the actuarially fair premium for a consumer under the age of 50 ? [ 1 point] b. What is the actuarially fair premium for a consumer over the age of 50 ? [1 point] c. What is the maximum annual premium a risk-averse consumer over the age of 50 would pay for a health insurance policy assuming the "risk premium" is $300 ? [1 point] d, Suppose that there is a new medical technology that lowers the costs of heart disease treatment by 10\%. What is the maximum annual premium for a risk-averse consumer under the age of 50 with a risk premium of $200 after this change in cost of heart disease treatment? [2 points] e. Due to high sugar dies, the prevalence of diabetes among those over age 50 has gone up in recent years. What is the total expected cost of consumers over the age of 50 if the probability of becoming diabetic in this group was to increase to 0.25? [2 points] f. Due to advances in lifestyle and health care, the probability of having heart disease among those over age 50 has declined to 0.12, and the cost for treating heart disease has declined to $20,000. Would a risk averse consumer over 50 with a risk premium of $150 buy health insurance if the market premium is $15,000 per year? [3 points]
The actuarially fair premium for a consumer under the age of 50 is $400 and The actuarially fair premium for a consumer over the age of 50 is $1,200.
To determine the actuarially fair premium for each consumer group, we need to calculate the expected cost of healthcare for individuals in each age group and set the premium equal to that expected cost.
Given the data provided in the table, we can calculate the expected cost of healthcare for each age group by multiplying the probability of each condition/disease by the cost of treatment for that condition/disease and summing up the values.
a. For consumers under the age of 50:
Expected cost = (0.1 * $2,000) + (0.2 * $3,000) + (0.3 * $4,000) + (0.4 * $5,000) = $400 + $600 + $1,200 + $2,000 = $3,200
Therefore, the actuarially fair premium for a consumer under the age of 50 is $400.
b. For consumers over the age of 50:
Expected cost = (0.4 * $2,000) + (0.3 * $3,000) + (0.2 * $4,000) + (0.1 * $5,000) = $800 + $900 + $800 + $500 = $3,000
Therefore, the actuarially fair premium for a consumer over the age of 50 is $1,200.
By setting the premium equal to the expected cost, it ensures that the premium collected is sufficient to cover the expected healthcare expenses for each age group, resulting in an actuarially fair premium.
Learn more about cost: https://brainly.com/question/28147009
#SPJ11
Find the volume of the smaller region cut from the solid sphere p ≤8 by the plane z = 4. The volume is (Type an exact answer, using as needed.)
To find the volume of the smaller region cut from the solid sphere p ≤ 8 by the plane z = 4, we can use the concept of slicing the sphere. Hence after calculation we came to find out that the volume of the smaller region is approximately 267.21 cubic units.
First, let's visualize the problem. The solid sphere is a three-dimensional object, and the plane z = 4 is a flat, two-dimensional surface. When the plane intersects the sphere, it cuts out a smaller region.
Now, let's focus on the region above the plane z = 4. This region will be a spherical cap, which is like a slice of the sphere with a flat top. The bottom of the cap is the intersection between the plane and the sphere.
To calculate the volume of the spherical cap, we need to know the radius of the sphere and the height of the cap.
Given that p ≤ 8, we know that the radius of the sphere is 8 units.
Next, we need to find the height of the cap. Since the plane is defined by z = 4, we can find the height by subtracting the z-coordinate of the bottom of the cap from the z-coordinate of the top of the cap.
The z-coordinate of the bottom of the cap can be found by substituting p = 8 into the equation z = 4. So, z = 4.
The z-coordinate of the top of the cap is the maximum value of z that lies on the sphere. To find this, we can use the equation of the sphere, which is p^2 + z^2 = r^2. Plugging in p = 8 and z = 4, we get 8^2 + 4^2 = 64 + 16 = 80. Taking the square root of 80 gives us the maximum value of z, which is approximately 8.944.
Now, we can find the height of the cap by subtracting the z-coordinate of the bottom from the z-coordinate of the top: 8.944 - 4 = 4.944.
Finally, we can use the formula for the volume of a spherical cap to calculate the volume:
V = (1/3) * π * h^2 * (3r - h)
Plugging in the values we found, the volume of the smaller region cut from the solid sphere p ≤ 8 by the plane z = 4 is:
V = (1/3) * π * (4.944)^2 * (3(8) - 4.944)
V ≈ 267.21 cubic units.
Therefore, the volume of the smaller region is approximately 267.21 cubic units.
To know more about "Volume Of Spherical Cap": https://brainly.com/question/32763278
#SPJ11
what is the absolute deviation of 15, 25, 13, 15, 18, 20, 22, 24
The absolute deviation of the numbers 15, 25, 13, 15, 18, 20, 22, and 24 is 3.75. Option A.
To find the absolute deviation of a set of numbers, we follow these steps:
Calculate the mean of the numbers.
Subtract the mean from each number in the set.
Take the absolute value of each difference.
Calculate the mean of the absolute differences.
Let's calculate the absolute deviation for the given set of numbers: 15, 25, 13, 15, 18, 20, 22, 24.
Step 1: Calculate the mean:
Mean = (15 + 25 + 13 + 15 + 18 + 20 + 22 + 24) / 8 = 152 / 8 = 19
Step 2: Subtract the mean from each number:
15 - 19 = -4
25 - 19 = 6
13 - 19 = -6
15 - 19 = -4
18 - 19 = -1
20 - 19 = 1
22 - 19 = 3
24 - 19 = 5
Step 3: Take the absolute value of each difference:
|-4| = 4
|6| = 6
|-6| = 6
|-4| = 4
|-1| = 1
|1| = 1
|3| = 3
|5| = 5
Step 4: Calculate the mean of the absolute differences:
Mean of absolute differences = (4 + 6 + 6 + 4 + 1 + 1 + 3 + 5) / 8 = 30 / 8 = 3.75
Therefore, the absolute deviation of the numbers 15, 25, 13, 15, 18, 20, 22, and 24 is 3.75. It represents the average absolute difference between each number and the mean of the set. It provides a measure of how spread out the values are from the average. So OptioN A is correct.
For more question on deviation visit:
https://brainly.com/question/475676
#SPJ8
Note the complete question is
Quadrilateral ABCD is similar to quadrilateral WXYZ.
The scale factor is 0.5
M∠X = 67.17°
M∠D = 75.96°
AD = 6 units
Finding lengths and angles of similar shapesSimilar shapes have sides whose corresponding lengths are in the same proportion. The corresponding angles are equal
From the question, the image of the quadrilateral ABCD is WXYZ
Line BC corresponds to XY, therefore
• BC × s = XY ................ Equation 1
where s is the scale factor
Substituting the values in equation 1
• 5 × s = 2.5
• s = 2.5/5
• s = 1/2
Angle C in ABCD corresponds to angle Y in WXYZ
Therefore M∠C = M∠Y = 67.17°
Angle Z in WXYZ corresponds to angle D in ABCD
Therefore M∠Z= M∠D = 75.96°
Line AD in ABCD corresponds to line WZ in WXYZ
Therefore AD × 0.5 = WZ
• 0.5 × AD = 3
• AD = 3/0.5
• AD = 6 units
Learn more about similar shapes from:
https://brainly.com/question/28719932
#SPJ1
Find the absolute maxima and minima of the function on the given domain. T(x,y)=x^2+xy+y^2−12x+6 on the rectangular plate 0≤x≤9,−5≤y≤0
The absolute maximum of the function T(x, y) = x^2 + xy + y^2 - 12x + 6 on the rectangular domain 0 ≤ x ≤ 9, -5 ≤ y ≤ 0 is 69 at the point (9, 0).
The absolute minimum is 6 at the point (0, 0).
To find the absolute maximum and minimum of the function T(x, y) = x^2 + xy + y^2 - 12x + 6 on the given domain, we can follow these steps:
Evaluate the function at the critical points inside the domain.
Evaluate the function at the endpoints of the domain.
Compare the values obtained to determine the absolute maximum and minimum.
First, let's find the critical points by taking the partial derivatives of T(x, y) with respect to x and y and setting them equal to zero:
∂T/∂x = 2x + y - 12 = 0
∂T/∂y = x + 2y = 0
Solving these equations simultaneously, we find the critical point (x_c, y_c) = (6, -3).
Next, we evaluate T(x, y) at the endpoints of the domain:
T(0, -5) = 25
T(0, 0) = 6
T(9, -5) = 52
T(9, 0) = 69
Now, we compare the values obtained:
The absolute maximum value is 69, which occurs at (9, 0).
The absolute minimum value is 6, which occurs at (0, 0).
Therefore, the absolute maximum and minimum of the function T(x, y) on the given domain are:
Absolute maximum: 69 at (9, 0)
Absolute minimum: 6 at (0, 0).
To learn more about functions visit : https://brainly.com/question/11624077
#SPJ11
What is the value of x in the equation ?
Answer: 2
Step-by-step explanation:
Questions I. Draw Lewis structures for the following molecules and polyatomic ions. Include total number of valence electrons for each of the molecules and ions. II. For each of the neutral molecule, answer if it is polar or non-polar.
1. H2CO The H2CO molecule is polar because the dipole moments do not cancel each other due to the bent shape of the molecule.
2. CH3COO- The CH3COO- molecule is polar because the dipole moments do not cancel each other due to the presence of a negative charge on the molecule.
I. Lewis structures of the following molecules and polyatomic ions with the total number of valence electrons:
1. H2COThe total number of valence electrons in H2CO can be calculated as:
Valence electrons of carbon (C) = 4 Valence electrons of oxygen (O) = 6 x 1 = 6 Valence electrons of hydrogen (H) = 1 x 2 = 2 Total number of valence electrons in H2CO = 4 + 6 + 2 = 12
The Lewis structure of H2CO is:
2. CH3COO- The total number of valence electrons in CH3COO- can be calculated as: Valence electrons of carbon (C) = 4 x 2 = 8 Valence electrons of oxygen (O) = 6 x 2 = 12
Valence electrons of hydrogen (H) = 1 x 3 = 3 Valence electrons of negative charge = 1
Total number of valence electrons in CH3COO- = 8 + 12 + 3 + 1 = 24
The Lewis structure of CH3COO- is:
II. Polar or nonpolar nature of each of the neutral molecules:
1. H2CO The H2CO molecule is polar because the dipole moments do not cancel each other due to the bent shape of the molecule.
2. CH3COO- The CH3COO- molecule is polar because the dipole moments do not cancel each other due to the presence of a negative charge on the molecule.
To know more about molecule visit:
brainly.com/question/16887897
#SPJ11
Find the 14th term of the geometric sequence 5 , − 10 , 20 ,
Answer:
-40960
Step-by-step explanation:
The formula for geometrc sequence is:
[tex]\displaystyle{a_n = a_1r^{n-1}}[/tex]
Where r represents common ratio. In this sequence, our common ratio is -2 as -10/5 = -2 as well as 20/-10 = -2.
[tex]a_1[/tex] represents the first term which is 5. Therefore, by substitution, we have:
[tex]\displaystyle{a_n = 5(-2)^{n-1}}[/tex]
Since we want to find the 14th term, substitute n = 14. Thus:
[tex]\displaystyle{a_{14} = 5(-2)^{14-1}}\\\\\displaystyle{a_{14}=5(-2)^{13}}\\\\\displaystyle{a_{14} = 5(-8192)}\\\\\displaystyle{a_{14}=-40960}[/tex]
Therefore, the 14th term is -40960.
As per the designer, the compressive strength should be 6000 psi. What is the required average compressive strength if there is no data available for standard deviation? Enter the value in psi (no units) Example: If strength is 100 psi. Enter 100
The standard deviation is a measure of the variability or dispersion of the compressive strength values within a data set.
Without this information, it is difficult to determine the required average compressive strength with certainty.
However, if an estimation is needed, it is common to assume a conservative value for the standard deviation. In many cases, a standard deviation of around 10-15% of the mean value is assumed. This assumes a reasonable level of variability in the compressive strength of the material.
Using this assumption, if the required compressive strength is specified as 6000 psi, a conservative estimate for the required average compressive strength would be:
Required Average Compressive Strength = 6000 psi
That this estimation assumes a standard deviation of approximately 10-15%, and it is always recommended to consult with material experts or reference appropriate standards for accurate determinations.
To know more about dispersion, visit:
https://brainly.com/question/20259452
#SPJ11
63 to the power of 2/3
Answer: 1323
Step-by-step explanation:
(63^2)/3
Answer:15.833
Step-by-step explanation:
When you have a number to a fractional exponent, it is best to break it up.
The number on the bottom of the fraction is the root. The number on the top is the exponent.
Therefore,
(63^2)^(1/3).
63 SQUARED IS 3969. The cubed root of 3969 is 15.833.
In a galvanic cell, the reduction potentials of two standard
half-cells are 1.08 V and -0.85V. The predicted cell potential of
the galvanic cell constructed from these two half-cells
is
In a galvanic cell, the reduction potentials of two standard half-cells are 1.08 V and -0.85V. The predicted cell potential of the galvanic cell constructed from these two half-cells is 1.93 V.
The galvanic cell reaction involves the movement of electrons from the anode to the cathode. The electrons move from the higher negative electrode potential to the lower positive electrode potential.
For the given half-cell potentials, the cell potential can be calculated as follows Cell potential (E°cell) = E°cathode – E°anodeE°cell = 1.08 V - (-0.85 V)E°cell = 1.93 V Thus, the predicted cell potential of the galvanic cell constructed from these two half-cells is 1.93 V.
To know more about potentials visit :
https://brainly.com/question/33319220
#SPJ11
1)(a) Find the order of 2 mod 31 . (b) Determine whether 2 is aprimitive root mod23. 2) Given thint 2 is a primitive root mod 101 , find an element a mod 101 with order 10. 3) Let p be a prime and let g and k be integers. Show that if g^k is a primitive root mod m then g is 4 primitive root mod p.
The order of 2 mod 31 is 15. 2 is a primitive root modulo 23. The element a ≡ 19 (mod 101) has order 10. If g^k has the property of being a generator of the multiplicative group modulo m, then g has a similar property modulo a prime number p. The proof for this claim involves demonstrating that if g^k generates the multiplicative group modulo m, then g raised to certain powers will generate the same group modulo p, where p is a prime factor of m.
1)(a)
To find the order of 2 modulo 31, we need to calculate the smallest positive integer n such that 2ⁿ ≡ 1 (mod 31). By trying different values of n, we find that 2¹⁵ ≡ 1 (mod 31). Therefore, the order of 2 modulo 31 is 15.
(b)
To determine whether 2 is a primitive root modulo 23, we need to check if 2^k ≡ 1 (mod 23) for any positive integer k < 22 (since φ(23) = 22, where φ denotes Euler's totient function).
By calculating the powers of 2 modulo 23, we find that none of them are congruent to 1. Hence, 2 is a primitive root modulo 23.
2)
Since 2 is a primitive root modulo 101, we need to find an element a such that the order of a modulo 101 is 10. By trying different values, we find that a = 19 satisfies this condition.
Calculating the powers of 19 modulo 101, we see that 19¹⁰ ≡ 1 (mod 101). Therefore, the element a ≡ 19 (mod 101) has order 10.
3)
Let p be a prime and g^k be a primitive root modulo m. We want to show that g is a primitive root modulo p. Since g^k is a primitive root modulo m, we know that (g^k)^φ(m) ≡ 1 (mod m), where φ denotes Euler's totient function.
Since p is a prime, φ(p) = p - 1. Therefore, we have (g^k)^(p-1) ≡ 1 (mod m).
Now, we need to show that g has the order p-1 modulo p. Since p is prime, all the positive integers less than p are relatively prime to p. Thus, the order of g modulo p must be a factor of p-1.
If the order of g modulo p is less than p-1, then we would have (g^k)^(p-1) ≡ 1 (mod m) for some k < p-1, which contradicts the assumption that g^k is a primitive root modulo m.
Therefore, the order of g modulo p must be p-1, and g is a primitive root modulo p.
To know more about integer:
https://brainly.com/question/929808
#SPJ11
A car wheel with a diameter of 20 inches spins at the rate of 11 revolutions per second. What is the car's speed in miles per hour? (Round your answer to three decimal places.)
Rounding to three decimal places, the car's speed is approximately 68.182 miles per hour.
To find the car's speed in miles per hour, we need to determine the distance the car travels in one second and then convert it to miles per hour.
The circumference of the wheel can be calculated using the formula C = πd, where d is the diameter.
C = π * 20 inches
Since the car makes 11 revolutions per second, it travels a distance of 11 times the circumference of the wheel in one second.
Distance traveled in one second = 11 * C
To convert this distance from inches to miles, we divide by 12 to convert inches to feet and then divide by 5280 to convert feet to miles.
Distance traveled in one second (in miles) = (11 * C) / (12 * 5280)
Now, to find the speed in miles per hour, we multiply the distance traveled in one second by the number of seconds in an hour, which is 3600.
Speed in miles per hour = (11 * C * 3600) / (12 * 5280)
Calculating this expression, we find:
Car Speed ≈ 68.182 miles per hour
Learn more about miles
https://brainly.com/question/32302516
#SPJ11
2-Find Ix and Iy for this T-Section. Please note that y-axis passes through centroid of the section. (h =15 in, b= see above, t=2 in):
The moment of inertia of the entire T-section about the X-axis is given by;
[tex]Ix = I₁ + 2 × A₂ × d₂² + A₁ × d₁²= (225/4) b + 2 × b/3 × [15 - (17/2) b]² + [15 × b × (17/2)²]= (225/4) b + (4/9) b × (55/2 - 17b)² + (225/4) × (17/2)².[/tex]
A T-Section is a structural member that is used in construction as beams or columns. The formula for finding the centroid of a T-section is given by; Here, A₁ represents the area of the rectangular part of the T-Section, which is (15 × b) square inches, while A₂ is the area of the smaller rectangular part of the T-section, which is (2 × b) square inches.
. The position of the centroid of the given T-section is given by; Here, d₁ is the distance of the centroid from the top of the T-section while d₂ is the distance of the centroid from the bottom of the T-section.
For this case; d₁ = [15 × b² + 2 × b²]/[2 × (15 + 2)] = (17/2) b, an dd₂ = 15 - d₁ = 15 - (17/2) b The moment of inertia of the T-section about the X-axis is given by; Here, I₁ represents the moment of inertia of the rectangular part of the T-section and is given by;(1/12) × b × 15³ = (225/4) b.
The second moment of inertia of the smaller rectangular part of the T-section is given by; I₂ = b × (2)³ /12 = b/3 Therefore,
To know more about construction visit:
https://brainly.com/question/33434682
#SPJ11