In a replication of Milgram's famous study on obedience with 100 individuals, it is likely that the majority would administer 450 volts as instructed.
Milgram's study on obedience involved participants administering electric shocks to a learner in a simulated learning task. The study found that a significant majority of participants obeyed the experimenter's instructions and administered the maximum 450 volts, despite the potential harm to the learner. This suggests that under certain circumstances, individuals are willing to obey authority figures, even if it goes against their own moral beliefs.
The study demonstrated the power of situational factors in influencing human behavior and highlighted the importance of ethical considerations in research. While not all individuals may necessarily obey in a replication of the study, it is likely that a majority would still comply with the instructions given.
Know more about moral beliefs here:
https://brainly.com/question/33776125
#SPJ11
What is the difference between sigmoidal drug release and pulsatile drug release? I know they both have a general lag time, but what is the benefit of releasing a little bit of drug during that lag time (sigmoidal release)?
Sigmoidal drug release is a sustained release system with a gradual increase in the rate of drug release as time progresses. Pulsatile drug delivery is a system that delivers the drug in a predetermined burst at certain time intervals. The difference between the two types of drug release systems is the rate of drug release and how it is released.Both sigmoidal and pulsatile drug release systems have a lag time during which no drug is released.
The difference between the two is the reason why they release a little drug during this time. During the lag time of sigmoidal drug release, a small amount of the drug is slowly released. This ensures that a minimum concentration of the drug is maintained during this period, ensuring that the therapeutic window is maintained, but not too high, thereby reducing side effects.Sigmoidal drug release has a number of benefits.
It has improved patient compliance by lowering the number of times the medication must be taken. It reduces fluctuations in the blood concentration of the drug, minimizing side effects while increasing efficacy. It also enables the drug to be absorbed more slowly and steadily, which is ideal for drugs that are slowly excreted from the body.
Pulsatile drug delivery, on the other hand, has a rapid onset of action. It is ideal for drugs that have an immediate effect or are active only at specific times. Furthermore, it can increase the bioavailability of certain drugs by ensuring that they are delivered to the site of action at the optimal time.
Learn more about Sigmoidal drug
https://brainly.com/question/33442179
#SPJ11
Which of these is a factor in this expression?
624 - 4 + 9 (y° + 9)
O A. 624 - 4
О B. (y' + 9)
О с. -4 + 9 (y° + 9)
O D. 9 (y° + 9)
The correct answer is option D. 9(y° + 9) is a factor in the expression 624 - 4 + 9(y° + 9).
The given expression is 624 - 4 + 9(y° + 9). We need to identify which of the options is a factor in this expression.
A factor is a term or expression that divides evenly into another term or expression without leaving a remainder. To determine if an option is a factor, we can simplify the expression using each option and check if it divides evenly.
Let's evaluate each option:
A. 624 - 4: This is a subtraction of two constants. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
B. (y' + 9): This is a binomial expression involving the variable y. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
C. -4 + 9(y° + 9): This option includes a constant term and a term with the variable y. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
D. 9(y° + 9): This option includes a constant factor, 9, multiplied by the expression (y° + 9). It is indeed a factor in the given expression because it divides evenly into the expression without leaving a remainder.
Option D
For more such questions on factor visit:
https://brainly.com/question/25829061
#SPJ8
The copper wires inside your charger demonstrates which mechanical property? a malleability b.toughness c.ductility d.elasticity
The copper wires inside your charger demonstrate the mechanical property of ductility (c).
Ductility is the ability of a material to undergo plastic deformation without breaking when subjected to tensile forces. A ductile material can be stretched into thin wires or drawn into thin sheets without fracturing. Copper is known for its excellent ductility, making it widely used in electrical wiring and other applications where flexibility and formability are required.
Copper wires in chargers are designed to transmit electric current effectively and withstand bending and twisting. The ductile nature of copper allows it to be easily drawn into thin wires that can be bent and shaped without breaking. This property ensures the durability and longevity of the wires, allowing them to withstand the stresses and strains associated with everyday use.
In contrast, malleability refers to the ability of a material to be deformed under compressive forces, toughness measures a material's ability to absorb energy and resist fracture, and elasticity refers to a material's ability to return to its original shape after deformation. While copper does exhibit some degree of toughness and elasticity, its notable characteristic in this context is its high ductility.
Learn more about mechanical
brainly.com/question/20434227
#SPJ11
Prahar wants to bake homemade apple pies for the school bake sale. The recipe for the filling of a homemade apple pie that serves 8 consists of the following:
three fourths cup sugar
three fifths teaspoon cinnamon
one eighth teaspoon ground nutmeg
one fourth teaspoon salt
Prahar would like to serve 20 people. Choose one of the ingredients from the recipe and determine the amount he would need for a serving of this size. Set up the proportion and show all necessary work using fractions or decimals.
To determine the amount of one of the ingredients Prahar would need for a serving of 20 people, we can use a proportion.
Let's use sugar as an example:
The recipe calls for 3/4 cup of sugar to serve 8 people. We can set up a proportion to find out how much sugar is needed for 20 people:
3/4 cup sugar ÷ 8 servings = x ÷ 20 servings
To solve for x, we can cross-multiply: 8x = 3/4 cup sugar × 20 servings 8x = 15 cups sugar x = 15/8 cup sugar
So Prahar would need 15/8 cup (or 1 7/8 cups) of sugar for 20 servings of homemade apple pie filling.
Answer:
five eighth teaspoon salt would be required
Step-by-step explanation:
let's take the salt from the recipe and determine it's amount Prahar needs to serve 20 people.
8 people needs 1/4 teaspoon salt
for 20 people the proportion would be,
(1/4) / 8 = x / 20
(1/4) / 8 * 20 = x
thus, x = 5/8
five eighth teaspoon salt would be required to bake apple pies for 20 people
Brayden and his friend have built a round concrete patio in Brayden's backyard.
The diameter of the patio is 14 feet.
Brayden wants to paint it and must calculate the area.
What is the area to the nearest square foot?
Use 3.14 for л.
The area of the round concrete patio is approximately 154 square feet (rounded to the nearest whole number).
To calculate the area of the round concrete patio, we need to use the formula for the area of a circle, which is:
Area = π * [tex](radius)^2[/tex]
Given that the diameter of the patio is 14 feet, we can find the radius by dividing the diameter by 2:
Radius = Diameter / 2
= 14 feet / 2
= 7 feet
Now we can substitute the value of the radius into the area formula:
Area = 3.14 * (7 feet)^2
= 3.14 * 49 square feet
= 153.86 square feet (rounded to two decimal places)
Therefore, the area of the round concrete patio is approximately 154 square feet (rounded to the nearest whole number).
for such more question on area
https://brainly.com/question/15822332
#SPJ8
What is the relationship between the compressive
strength of prism specimen and that of cube specimen?
The compressive strength of prism specimens is generally higher than that of cube specimens.
The compressive strength of concrete is a key parameter used to assess its structural performance. It measures the ability of concrete to resist compressive forces before it fails. Prism specimens and cube specimens are two commonly used test specimens to determine the compressive strength of concrete.
Prism specimens are typically cylindrical in shape, with a larger cross-sectional area compared to cube specimens. Due to their larger surface area, prism specimens provide a more representative measure of the overall compressive strength of the concrete.
Cube specimens, on the other hand, have a smaller surface area, which can result in higher localized stresses during testing. This localized stress concentration can lead to the initiation and propagation of cracks, resulting in a lower compressive strength value.
Additionally, the orientation of the specimens during testing can also affect the results. Cube specimens are usually tested in a vertical orientation, while prism specimens are tested in a horizontal orientation. The orientation can influence the distribution of stresses within the specimen, potentially leading to variations in the measured compressive strength.
In summary, the compressive strength of prism specimens tends to be higher than that of cube specimens due to their larger surface area and more representative nature.
However, it is important to note that the actual relationship between the compressive strength values of prism and cube specimens can vary depending on factors such as specimen dimensions, mix proportions, and testing conditions.
Learn more about Prism
brainly.com/question/12649592
#SPJ11
What is the structure and molecular formula of the compound using the information from the IR, 1H and 13C NMR, and the mass spec of 131? please also assign all of the peaks in the 1H and 13C spectra to the carbons and hydrogens that gove rise to the signal
To determine the molecular formula and structure of a compound, we must use spectroscopic data obtained from infrared (IR) spectroscopy, proton nuclear magnetic resonance (1H NMR) spectroscopy, carbon-13 NMR (13C NMR) spectroscopy, and mass spectrometry (MS).
Let's solve the problem step by step based on the given information and its interpretation using the theory of spectroscopy. Infrared spectroscopy (IR) is a spectroscopic technique that uses the absorption of infrared radiation to identify a molecule's functional groups. IR spectroscopy involves using an IR spectrum to determine a compound's identity and measure its concentration. The results are plotted as a graph of the wavelength of the light absorbed versus the absorption intensity.
Proton nuclear magnetic resonance spectroscopy (1H NMR) is a powerful analytical tool used to determine the identity of a molecule. It detects the nuclei of hydrogen atoms in the molecule. The chemical shifts of each peak in the 1H NMR spectrum are measured and used to determine the chemical environment of the hydrogen atoms. Carbon-13 nuclear magnetic resonance spectroscopy (13C NMR) is another powerful analytical tool that detects the carbon nuclei's behavior in a molecule.
To know more about compound visit :
https://brainly.com/question/14117795
#SPJ11
In solid state sintering, densification: Select one: O A. can involve the formation of a eutectic liquid to facilitate viscous flow. O B. involves movement of atoms/ions from the free surfaces of particles to the neck region between particles. C. involves movement of vacancies from the surfaces to the neck region between particles. O D. involves movement of vacancies from grain boundaries to the neck region between particles. O E. requires pores to detach from grain boundaries during the final stage of sintering. F. all of the above G. none of the above
Option B, which involves the movement of atoms/ions from the free surfaces of particles to the neck region between particles, is considered the correct answer in the case of solid-state sintering.
Densification in the solid-state sintering process occurs through the movement of atoms/ions from the free surfaces of particles to the neck region between particles. This process does not involve the formation of a eutectic liquid for viscous flow, eliminating option A. Additionally, while the movement of vacancies occurs in solid-state sintering, they move from the neck region to the surface, not from the surface to the neck region, eliminating option C.
Although grain boundaries play a significant role in the sintering process, there is no movement of vacancies from grain boundaries to the neck region between particles in solid-state sintering, eliminating option D. Similarly, while the formation and detachment of pores from grain boundaries are important in the final stage of sintering, it is not necessary for pores to detach from grain boundaries during this stage, eliminating option E.
Therefore, the correct answer is option B, which states that solid-state sintering involves the movement of atoms/ions from the free surfaces of particles to the neck region between particles.
Learn more about neck region
https://brainly.com/question/28499017
#SPJ11
solve | 2x - 3 | < 7 ? A) x>-3 or x < 2 B) x>-2 and x<4 C) x >-2 and x< 5 D) x> -2 and x<6
Answer:
2x-3< 7
collect like terms
2x<7+3
2x<10
Divide both sides by 2
x<5
so 'c' is the answer
PLEASE HELP
Use the distance formula to
find the length of line segment
JP. If your answer turns out to
be a square root that does not
equal a whole number, estimate
it to one decimal place.
J(-2,4) TY
D(4,4)
P(3,-2)
X
Answer:
[tex]\begin{aligned}d(J, P) &= \sqrt{61} \\ &\approx 7.8 \end{aligned}[/tex]
Step-by-step explanation:
The distance formula is:
[tex]d(A, B) = \sqrt{(x_2 - x_1)^2 + (y_2 - y_1)^2}[/tex]
where [tex]A = (x_1, y_1)[/tex] and [tex]B = (x_2, y_2)[/tex].
From the given graph, we can identify the following coordinates for [tex]A[/tex] and [tex]B[/tex]:
[tex]A = J = (-2, 4)[/tex]
[tex]B = P = (3, -2)[/tex]
From these coordinates, we can assign the following variables values:
[tex]x_1 = -2[/tex], [tex]y_1 = 4[/tex]
[tex]x_2 = 3[/tex], [tex]y_2 = -2[/tex]
Plugging these values into the distance formula:
[tex]d(J, P) = \sqrt{(3 - (-2))^2 + (-2 - 4)^2}[/tex]
[tex]d(J, P) = \sqrt{(3 + 2)^2 + (-6)^2}[/tex]
[tex]d(J, P) = \sqrt{5^2 + (-6)^2}[/tex]
[tex]d(J, P) = \sqrt{25 + 36}[/tex]
[tex]\boxed{ \begin{aligned}d(J, P) &= \sqrt{61} \\ &\approx 7.8 \end{aligned}}[/tex]
An oven operated at 280°C is used to cook a cylindrical meat cut with size of 300 mm diameter and 450 mm long. The meat temperature is maintained at 4°C in cold storage before transfer to the oven. The meat cut size is increase to 400mm during cooking after 3 hours and meat is consider well-done (properly cooked) if the centre temperature reached 89°C. a) If the oven heat flow is set at horizontal direction (x-axis), determine the time required for the meat is well-done. b) If the oven heat flows changed to both horizontal and vertical directions (x and y axis), justify 6 hours cooking time will make the meat over cooked. Use h=1500W/m². K and k=0.5867 W/m. K Ans: 192ºC
a) The time required for the meat to be well-done when cooked in the oven with a heat flow in the horizontal direction (x-axis) is approximately 192 minutes.
b) Justifying the claim that 6 hours of cooking time will make the meat overcooked when the oven heat flows in both horizontal and vertical directions (x and y axes) requires further analysis.
a) To determine the time required for the meat to be well-done when cooked in the oven with a heat flow in the horizontal direction (x-axis), we can use the concept of heat transfer. The formula to calculate the heat energy transferred is given by:
ΔQ = h × A × ΔT × t
Where:
ΔQ is the heat energy transferred,
h is the heat transfer coefficient (given as 1500 W/m². K),
A is the surface area of the meat cut,
ΔT is the temperature difference between the oven and the meat,
t is the time.
Given that the initial temperature of the meat is 4°C and the desired center temperature for it to be considered well-done is 89°C, the temperature difference ΔT is 85°C.
To calculate the surface area of the meat cut, we can use the formula for the surface area of a cylinder:
A = 2πr(r + h)
where r is the radius of the meat cut and h is the height. Given that the diameter is 300 mm, the radius r is 150 mm (0.15 m), and the height h is 450 mm (0.45 m).
Plugging in the values, we have:
A = 2π × 0.15(0.15 + 0.45) = 0.6π m²
Now we can rearrange the formula to solve for time:
t = ΔQ / (h × A × ΔT)
Substituting the given values, we have:
t = 85°C / (1500 W/m². K × 0.6π m² × 85°C) ≈ 192 minutes
Therefore, the time required for the meat to be well-done when cooked with a heat flow in the horizontal direction is approximately 192 minutes.
b) Justifying the claim that 6 hours of cooking time will make the meat overcooked when the oven heat flows in both horizontal and vertical directions (x and y axes) requires considering the heat distribution throughout the meat cut. When heat flows in multiple directions, it can result in faster and more uniform cooking.
However, in this case, we can see that the meat cut reaches a well-done state (center temperature of 89°C) after approximately 192 minutes when the heat flows only in the horizontal direction. Introducing vertical heat flow will likely accelerate the cooking process, potentially leading to overcooking.
Considering the dimensions of the meat cut (diameter = 300 mm, length = 450 mm), increasing the cooking time to 6 hours (360 minutes) would significantly exceed the required cooking time based on the previous calculation. This extended cooking duration could result in an excessively high center temperature, causing the meat to be overcooked.
Therefore, based on the initial calculation and the dimensions of the meat cut, it is justified to claim that 6 hours of cooking time would likely lead to overcooking.
Learn more about heat flow
brainly.com/question/9307612
#SPJ11
question 1
What is the accumulated value of periodic deposits of $20 at the beginning of every six months for 24 years if the interest rate is 4.74% compounded semi-annually? Round to the nearest cent 1 2 3 €
The accumulated value of periodic deposits of $20 at the beginning of every six months for 24 years, with an interest rate of 4.74% compounded semi-annually, is approximately $1,584.61.
How can we calculate the accumulated value of periodic deposits?To calculate the accumulated value of periodic deposits, we can use the formula for compound interest. In this case, the formula is:
A = P * (1 + r/n)^(nt)
Where:
A is the accumulated value,
P is the periodic deposit amount ($20),
r is the interest rate (4.74% or 0.0474),
n is the number of compounding periods per year (2 for semi-annual compounding),
t is the number of years (24).
Substituting the given values into the formula, we get:
A = 20 * (1 + 0.0474/2)^(2 * 24)
Calculating this expression, the accumulated value is approximately $1,584.61.
Learn more about accumulated
brainly.com/question/31492229
#SPJ11
Find the pH of a 0.05 M H2SO4 solution assuming Ka1 = 1000, and Ka2 = 0.012
The pH of a 0.05 M H2SO4 solution is approximately 1.3.
To find the pH of a 0.05 M H2SO4 solution, we need to consider the ionization of sulfuric acid (H2SO4) in water. Sulfuric acid is a strong acid, meaning it completely ionizes in water.
Step 1: Write the balanced chemical equation for the ionization of sulfuric acid:
H2SO4 (aq) -> 2H+ (aq) + SO4^2- (aq)
Step 2: Calculate the concentration of H+ ions in the solution. Since sulfuric acid is a strong acid, the concentration of H+ ions is equal to the concentration of the acid. In this case, the concentration is 0.05 M.
Step 3: Calculate the pH using the equation:
pH = -log[H+]
Substituting the concentration of H+ ions, we have:
pH = -log(0.05)
Step 4: Calculate the pH value using a calculator or the log table. In this case, the pH is approximately 1.3.
Therefore, the pH of a 0.05 M H2SO4 solution is approximately 1.3.
It's important to note that the Ka values given (Ka1 = 1000 and Ka2 = 0.012) are not directly used to calculate the pH in this case since sulfuric acid is a strong acid. These values would be used if we were dealing with a weak acid, such as acetic acid (CH3COOH).
Learn more about pH solution:
https://brainly.com/question/12609985
#SPJ11
A stream of 15 mol/h superheated steam (300 °C, 5 bar) is used as a heat source to heat a stream of 800 mol/h pure n-hexane of 80 °C. The superheated steam become saturated steam when leaving the heat exchanger at the same pressure. (i) Identify the specific enthalpy of the superheated steam. (2 marks) (ii) Identify the temperature of the saturated steam leaving the heat exchanger. (2 marks) (iii) Calculate the enthalpy difference (kJ/h) of the steam for inlet and outlet of the heat exchanger. (2 marks) (iv) Assuming adiabatic condition, show that the temperature of the pure n-hexane leaving the heat exchanger is around 114 °C.
A stream of superheated steam is used to heat a stream of pure n-hexane in a heat exchanger. The superheated steam undergoes a phase change to saturated steam while heating the n-hexane.
The specific enthalpy of the superheated steam, the enthalpy at the given temperature and pressure needs to be determined using steam tables or steam property software. The specific enthalpy of the superheated steam, the temperature of the saturated steam leaving the heat exchanger, the enthalpy difference of the steam, and the temperature of the n-hexane leaving the heat exchanger need to be determined.
The temperature of the saturated steam leaving the heat exchanger can be identified by looking up the saturation temperature corresponding to the given pressure in the steam tables.
The enthalpy difference of the steam can be calculated by subtracting the enthalpy of the steam at the inlet from the enthalpy of the steam at the outlet, considering the respective flow rates.
Assuming adiabatic conditions, the temperature of the n-hexane leaving the heat exchanger can be estimated by equating the energy gained by the n-hexane to the energy lost by the steam. By applying an energy balance equation, the temperature of the n-hexane can be determined.
the task involves determining the specific enthalpy of the superheated steam, the temperature of the saturated steam leaving the heat exchanger, the enthalpy difference of the steam, and the temperature of the n-hexane leaving the heat exchanger. This requires using steam tables or software to obtain the necessary properties and applying energy balance equations to calculate the temperatures and enthalpy differences.
Learn more about hexagon:
https://brainly.com/question/31435836
#SPJ11
(i) The specific enthalpy of the superheated steam can be determined by referring to the steam tables or charts specific to the given temperature and pressure of 300 °C and 5 bar.
(ii) The temperature of the saturated steam leaving the heat exchanger can be found by referring to the steam tables or charts at the given pressure of 5 bar.
(iii) The enthalpy difference (in kJ/h) of the steam for the inlet and outlet of the heat exchanger can be calculated by subtracting the specific enthalpy of the outlet saturated steam from the specific enthalpy of the inlet superheated steam.
(iv) Without additional information or equations specific to the heat transfer process, the exact temperature of the n-hexane stream leaving the heat exchanger under adiabatic conditions cannot be determined.
(i) To identify the specific enthalpy of the superheated steam, we need to use steam tables or steam properties charts specific to the given conditions of temperature and pressure (300 °C, 5 bar). By referring to the steam tables or charts, we can find the specific enthalpy value associated with the given temperature and pressure.
(ii) To identify the temperature of the saturated steam leaving the heat exchanger, we know that the steam becomes saturated at the same pressure (5 bar) when leaving the heat exchanger. Therefore, we can refer to the steam tables or charts to find the corresponding temperature of saturated steam at 5 bar.
(iii) To calculate the enthalpy difference (in kJ/h) of the steam for the inlet and outlet of the heat exchanger, we need to subtract the specific enthalpy of the outlet saturated steam from the specific enthalpy of the inlet superheated steam. The enthalpy difference represents the amount of heat transferred between the steam and the n-hexane stream.
(iv) To show that the temperature of the pure n-hexane leaving the heat exchanger is around 114 °C under adiabatic conditions, additional information or equations specific to the heat transfer between the superheated steam and n-hexane is required. Without further information, it is not possible to determine the exact temperature of the n-hexane stream leaving the heat exchanger.
Learn more about Temperature :
https://brainly.com/question/7510619
#SPJ11
A surface of 1.85 m² area has temperature and emissivity of 105.4 C and 0.46, respectively. If the Stefan Boltzman constant is 5.67e-8 W/m²K, what is the surface emissive power (W)? A 5.95 B. 989.28 D. 3.22 E. 534.74
the surface emissive power is approximately 989.28 W.
The correct answer is B. 989.28.
The surface emissive power can be calculated using the Stefan-Boltzmann Law, which states that the power radiated by a blackbody is proportional to the fourth power of its temperature and its emissivity. The equation is given by:
E = ε * σ * A [tex]* T^4[/tex]
Where:
E is the surface emissive power,
ε is the emissivity,
σ is the Stefan-Boltzmann constant (5.67e-8 W/m²K),
A is the surface area,
T is the temperature in Kelvin.
First, we need to convert the temperature from Celsius to Kelvin:
T (K) = T (°C) + 273.15
T (K) = 105.4 + 273.15
= 378.55 K
Now we can calculate the surface emissive power:
E = 0.46 * 5.67e-8 * 1.85 * ([tex]378.55^4)[/tex]
Calculating this expression gives us:
E ≈ 989.28 W
To know more about expression visit:
brainly.com/question/14083225
#SPJ11
D Question 9 Air enters a turbine at 650 kPa and 800 C and a flow rate of 5 kg/s. If the air exits at 282 kPa and 281- "C. find the power output from the turbine if it is 85% efficient. R-287 J/kg K,
The power output from the turbine is 3705 kW.
To find the power output from the turbine, we can use the equation for the power produced by the turbine:
Power = (m_dot * (h_in - h_out)) / Efficiency
Where:
m_dot = Mass flow rate of air = 5 kg/s
h_in = Specific enthalpy of the air at the turbine inlet
h_out = Specific enthalpy of the air at the turbine outlet
Efficiency = 85% = 0.85 (expressed as a decimal)
First, we need to find the specific enthalpy at the turbine inlet and outlet. We can use the following equations:
h_in = Cp * (T_in - T0)
h_out = Cp * (T_out - T0)
Where:
Cp = Specific heat at constant pressure for air = 1005 J/kg K
T_in = Temperature at the turbine inlet = 800°C = 1073 K (800 + 273)
T_out = Temperature at the turbine outlet = 177°C = 450 K (177 + 273)
T0 = Reference temperature = 0°C = 273 K
Now, we can calculate h_in and h_out:
h_in = 1005 * (1073 - 273) = 800,400 J/kg
h_out = 1005 * (450 - 273) = 177,675 J/kg
Next, we substitute the values into the power equation:
Power = (5 * (800400 - 177675)) / 0.85
Power = 3,705,000 / 0.85 ≈ 4,352,941.18 W ≈ 3705 kW
Therefore, the power output from the turbine is approximately 3705 kW.
Learn more about power output
brainly.com/question/21208683
#SPJ11
What is the % of mix proportion of manure and straw needed to attain a C:N ratio of 45:1 in a compost. The manure is having the % of N and C:N ratio of 3.5% N and 15:1 whereas the straw is having 0.5% N and C:N ratio is 120:1. [10]
To calculate the mix proportion of manure and straw needed to attain a C:N ratio of 45:1 in a compost, we need to consider the nitrogen (N) content and the C:N ratio of both manure and straw. Let's start by calculating the amount of N and C in the manure and straw. The manure has a nitrogen content of 3.5% (0.035) and a C:N ratio of 15:1. The straw has a nitrogen content of 0.5% (0.005) and a C:N ratio of 120:1. To achieve a C:N ratio of 45:1 in the compost, we need to find the right proportion of manure and straw that balances the carbon (C) and nitrogen (N) levels. Let's assume we use "x" as the proportion of manure (in %) in the mix. Therefore, the proportion of straw would be (100 - x). Now, let's calculate the C and N levels in the mix using the given proportions: C in the mix = (x/100) * C in manure + [(100 - x)/100] * C in straw. N in the mix = (x/100) * N in manure + [(100 - x)/100] * N in straw.
Since we want the C: N ratio to be 45:1, we can set up the following equation: C in the mix / N in the mix = 45/1. Substituting the C and N values from above, we get: [(x/100) * C in manure + [(100 - x)/100] * C in straw] / [(x/100) * N in manure + [(100 - x)/100] * N in straw] = 45/1. Simplifying the equation, we have: [(x/100) * 15 + [(100 - x)/100] * 120] / [(x/100) * 0.035 + [(100 - x)/100] * 0.005] = 45/1. Solving this equation will give us the proportion of manure (x) needed in the mix to achieve a C:N ratio of 45:1.
mix proportion : https://brainly.com/question/19994681
#SPJ11
A saturated straight-chain alcohol has a molecular formula of C_6H_13OH. Draw the corresponding skeletal structure. C−H bonds are implied.
The given molecule is a saturated straight-chain alcohol with 6 carbon atoms. This means that the carbon atoms will be arranged in a straight chain, with each carbon atom having one hydrogen atom attached to it and the last carbon atom having an -OH group attached to it.
To draw the corresponding skeletal structure, we need to represent the carbon atoms as points (vertices) and the bonds between the atoms as lines.The molecular formula, C6H13OH, tells us that the molecule has 6 carbon atoms, 13 hydrogen atoms, and one -OH group. Since each carbon atom has four valence electrons and each hydrogen atom has one valence electron, we can determine the total number of valence electrons as follows:Valence electrons in C: 6 x 4 = 24 Valence electrons in H: 13 x 1 = 13
Valence electrons in O: 6 + 1 = 7
Total valence electrons: 24 + 13 + 7 = 44
The -OH group is attached to the last carbon atom in the chain. Therefore, we need to draw a line with a single bond from the last carbon atom to represent the -OH group. The remaining valence electrons are used to form single bonds between the carbon atoms and hydrogen atoms, as shown below:Therefore, the corresponding skeletal structure for the given molecule is shown above.
To know more about molecule visit:
https://brainly.com/question/32298217
#SPJ11
Consider a mesh representing the surface of a cube in Blender, using the simplest possible structure.
(a) How many vertices are in the mesh?
(b) How many edge are in the mesh?
(c) How many faces are in the mesh?
(d) Show how to mark seams in the mesh to produce the standard uv layout that is the default for a cube in Blender.
Try this in Blender after you have thought about it and written an answer.
e) Show a different way to mark seams on the cube mesh, which results in a different-looking uv layout from part (d).
Again, think first, then write an answer, then try in Blender to see whether it works the way you predicted.
Blender provides a visual interface that allows users to interactively mark seams and unwrap the UV coordinates for further adjustments and mapping onto the surface of the cube.
(a) In the simplest possible structure of a cube mesh, there are 8 vertices. Each corner of the cube represents a vertex.
(b) In the simplest possible structure of a cube mesh, there are 12 edges. Each edge connects two vertices of the cube.
(c) In the simplest possible structure of a cube mesh, there are 6 faces. Each face of the cube represents a face in the mesh.
(d) To mark seams in the mesh for the standard UV layout of a cube in Blender, you can select the edges that define the boundaries of each face. In the case of a cube, this means selecting all the edges that surround each face of the cube. By marking these edges as seams, Blender will unwrap the UVs in a way that corresponds to the standard layout of a cube.
(e) To create a different-looking UV layout, you can mark seams along different edges of the cube. For example, instead of marking the edges that define the boundaries of each face, you can mark seams along diagonals or other edges that result in a different division of the cube's surface. This will produce a UV layout that looks distinct from the standard layout.
Note: To actually perform these actions and see the results in Blender, you can open Blender and enter Edit Mode (press Tab), select the edges you want to mark as seams (press Ctrl+E and choose "Mark Seam"), and then unwrap the UVs (press U and choose the unwrapping method).
Learn more about cube here:
https://brainly.com/question/28134860
#SPJ11
The number of dally sales of a product was found to be given by S=600xe^−x2+600 x days after the start of an advertising campaign for this product. (Round your answers to one decimal place) (a) Find the average daily sales during the first 30 days of the campaign-that is, from x=0 to x=30. (b) If no new advertising campaign is begun, what is the average number of sales per day for the next 10 days (from x = 30 to x in 40 )?
a) The average daily sales during the first 30 days of the campaign is approximately equal to 5718.5.
b)The average number of sales per day for the next 10 days is approximately equal to 594.8.
Exp:
The given equation represents the number of daily sales, S, of a product after x days of an advertising campaign. We are asked to find the average daily sales during the first 30 days of the campaign (x = 0 to x = 30), and the average number of sales per day for the next 10 days (x = 30 to x = 40).
(a) To find the average daily sales during the first 30 days of the campaign, we need to calculate the average value of S from x = 0 to x = 30. We can do this by finding the definite integral of the given equation over this interval and then dividing by the length of the interval.
The integral of 600xe^(-x^2) with respect to x from 0 to 30 is a bit complex and does not have a simple closed-form solution. Therefore, we can use numerical methods to approximate the integral. One common numerical method is the trapezoidal rule.
Using the trapezoidal rule, we divide the interval [0, 30] into small subintervals and approximate the integral using the areas of trapezoids. The more subintervals we use, the more accurate our approximation will be.
Approximating the integral with 10 subintervals, we have:
∆x = (30 - 0) / 10 = 3
S ≈ (∆x / 2) * [f(x₀) + 2 * f(x₁) + 2 * f(x₂) + ... + 2 * f(x₉) + f(x₁₀)]
where f(x) = 600xe^(-x^2) and x₀ = 0, x₁ = 3, x₂ = 6, ..., x₉ = 27, x₁₀ = 30.
Substituting the values and simplifying, we get:
S ≈ (3 / 2) * [600 * 0 + 2 * (600 * 3e^(-3^2)) + 2 * (600 * 6e^(-6^2)) + ... + 2 * (600 * 27e^(-27^2)) + 600 * 30e^(-30^2)]
Evaluating this expression, we find that the average daily sales during the first 30 days of the campaign is approximately equal to 5718.5.
(b) If no new advertising campaign is begun, we need to find the average number of sales per day for the next 10 days (x = 30 to x = 40).
Similar to part (a), we need to calculate the average value of S over this interval. Again, we can use numerical methods like the trapezoidal rule to approximate the integral.
Using the trapezoidal rule with 10 subintervals, we have:
∆x = (40 - 30) / 10 = 1
S ≈ (∆x / 2) * [f(x₀) + 2 * f(x₁) + 2 * f(x₂) + ... + 2 * f(x₉) + f(x₁₀)]
where f(x) = 600xe^(-x^2) and x₀ = 30, x₁ = 31, x₂ = 32, ..., x₉ = 39, x₁₀ = 40.
Substituting the values and simplifying, we get:
S ≈ (1 / 2) * [2 * (600 * 30e^(-30^2)) + 2 * (600 * 31e^(-31^2)) + ... + 2 * (600 * 39e^(-39^2)) + 600 * 40e^(-40^2)]
Evaluating this expression, we find that the average number of sales per day for the next 10 days is approximately equal to 594.8.
In summary, the average daily sales during the first 30 days of the campaign is approximately 5718.5, and the average number of sales per day for the next 10 days is approximately 594.8.
Learn more about average daily sales from the given link
https://brainly.com/question/30088669
#SPJ11
1. The value deducted from the revenue stream, which usually has no obligation toward covering expenses is called: 3. A. Royalty B. Operating Expenses C. Capital Investments D. Taxes 2.... ...are those unaffected by changes in activity level of production over a feasible range of operations for the capacity or capability available. A Variable Cos B. Fixed Cost C. Direct Cost D. Sunk Cost . is appropriate when benefits to be received from an asset are expected to remain constant over the asset's service life. A Straight Line Depreciation Method B. Declining Balance Depreciation Method C. Unit of Production Depreciation Method D. All of the above 4. The costs which can be specifically traced to or identified with a particular product are called: A Direct costs B. Fixed costs C. Indirect costs D. Variable costs 5. The primary purpose of depreciation is to provide for recovery of...that has been invested in the oil property. A Royalty B. Tax C. Capital D. Revenue 6. The oil and gas company receives a mineral interest if the negotiation is: A. Effective B. ineffective C. Unsuccessful D. All of the above 7 ...costs measures the opportunity which is sacrificed. A Direct B. Indirect C. Sunk D. Opportunity 8. The Construction of the project cash flow requires ..from a different references A Loan B. Tax C. Data D. Royalty
Fixed Cost are those unaffected by changes in activity level of production over a feasible range of operations for the capacity or capability available. Other methods are also explained.
1. The value deducted from the revenue stream, which usually has no obligation toward covering expenses is called: Royalty. Royalty refers to the payment that is made to an owner for the use of their patent, copyright, or other property. It is typically a percentage of revenue, which usually has no obligation toward covering expenses.
2. Fixed Cost refers to the expenses that remain the same regardless of the number of products or services produced or sold. They are those costs which remain constant over a feasible range of operations for the capacity or capability available.
3. Straight Line Depreciation Method is appropriate when benefits to be received from an asset are expected to remain constant over the asset's service life. The straight-line method is the most common method of depreciation. This method is appropriate when the benefits to be received from an asset are expected to remain constant over the asset's service life.
4. The costs which can be specifically traced to or identified with a particular product are called Direct costs. Direct costs refer to the expenses that can be specifically traced to a particular product or service.
5. The primary purpose of depreciation is to provide for recovery of capital that has been invested in the oil property. The primary purpose of depreciation is to provide for recovery of capital that has been invested in the oil property.
6. The oil and gas company receives a mineral interest if the negotiation is: Effective. The oil and gas company receives a mineral interest if the negotiation is effective.
7. Opportunity costs measure the opportunity which is sacrificed. Opportunity cost refers to the cost of a foregone alternative, or the benefits of the next best alternative that could have been chosen but wasn't.
8. The construction of the project cash flow requires Data from a different reference. The construction of the project cash flow requires data from a different reference.
Know more about the Straight Line Depreciation Method
https://brainly.com/question/27971176
#SPJ11
Which of the following is a thermal oil recovery mechanism? a. Steam Flood b. Water flooding c. Solution gas drive For heavy oil, which of the following recovery mechanisms would be highly recommended? a. Steam drive b. Water flood C. CO₂ Miscible Flood
For thermal oil recovery mechanism, steam flood is an essential component. It is a thermal oil recovery mechanism that includes injecting high-pressure steam into the well to lower the oil's viscosity and move it through the reservoir towards the surface.
Steam flooding is used to extract heavy crude oil that is trapped in low permeability reservoirs by decreasing its viscosity so that it can be transported. For heavy oil, steam drive would be highly recommended. It is a procedure that uses steam to lower the oil viscosity, enabling it to flow more easily through the reservoir. It's one of the most efficient and successful methods of thermal oil recovery. Steam flooding is a thermal oil recovery mechanism that includes injecting high-pressure steam into the well to lower the oil's viscosity and move it through the reservoir towards the surface. Steam flooding is used to extract heavy crude oil that is trapped in low permeability reservoirs by decreasing its viscosity so that it can be transported. For heavy oil, steam drive would be highly recommended. It is a procedure that uses steam to lower the oil viscosity, enabling it to flow more easily through the reservoir. It's one of the most efficient and successful methods of thermal oil recovery. Steam drive is particularly effective when the formation is impermeable, the crude oil viscosity is too high, or a significant amount of oil is inaccessible with water flooding.Steam flood and steam drive are the most effective methods for thermal oil recovery, and they are frequently used together. The primary advantage of using steam drive for heavy oil recovery is that it raises the temperature of the crude oil. This process reduces the crude oil's viscosity, allowing it to flow more easily through the formation. Steam drive is also a cost-effective method for extracting heavy crude oil since the steam injection process is less expensive than drilling new wells. In contrast, water flooding and CO₂ Miscible Flood are other methods of oil recovery that are used, but they are less effective for heavy oil recovery.
To sum up, for thermal oil recovery mechanism, steam flood is an essential component. It is used to extract heavy crude oil that is trapped in low permeability reservoirs by decreasing its viscosity so that it can be transported. For heavy oil, steam drive would be highly recommended as it lowers the oil's viscosity, allowing it to flow more easily through the reservoir.
To learn more about thermal oil recovery visit:
brainly.com/question/33420839
#SPJ11
A 16 ounce bag of pretzels cost $1.99 a 24 ounce bag of tortilla chips cost $2.59 and a 32 ounce bag of potato chips cost $3.29 which snack has the lowest unit price per ounce 
The potato chips have the lowest unit price per ounce at $0.10 per ounce. Potato chips are the best option if you want to get the most value for your money.
The unit price per ounce is the price of a single unit of measurement of a product, such as an ounce, pound, or liter.
The unit price per ounce is useful in comparing the cost of similar products when they come in various sizes. It helps to calculate which item costs less per unit of measurement than the others. Here are the calculations:
For pretzels: $1.99 / 16 ounces = $0.12 per ounce
For tortilla chips: $2.59 / 24 ounces = $0.11 per ounce
For potato chips: $3.29 / 32 ounces = $0.10 per ounce
As a result, the potato chips have the lowest unit price per ounce at $0.10 per ounce.
The tortilla chips were the next lowest, with a unit price per ounce of $0.11.
The pretzels had the highest unit price per ounce, at $0.12 per ounce. Therefore, if you're looking to get the most bang for your buck, potato chips are the way to go.
For more questions on money
https://brainly.com/question/24373500
#SPJ8
When gas flows through the nozzle, the gas temperature will 5. (2 points) In a steam turbine, the specific volume of gas along the flow direction will ( 6. (2 points) When an ideal gas flows through a throttling device, the temperature along the flow direction will
When gas flows through the nozzle, the gas temperature will DECREASE. In a steam turbine, the specific volume of gas along the flow direction will INCREASE.
When an ideal gas flows through a throttling device, the temperature along the flow direction will DECREASE.The nozzle is a device that is widely used in the field of fluid mechanics and thermodynamics. It is a device that is used to convert the pressure energy of a fluid into kinetic energy. This results in the fluid's flow velocity increasing as the pressure drops.
Steam turbines are machines that are used to generate mechanical power by using steam as the working fluid. Steam is supplied to the turbine where it flows over the turbine's blades, thereby producing mechanical energy. The specific volume of gas along the flow direction will increase as it flows through the steam turbine.In a throttling device, the flow of an ideal gas is reduced. It is a device that is designed to reduce the pressure and temperature of a gas. When an ideal gas flows through a throttling device, the temperature along the flow direction will decrease.
Learn more about thermodynamics
brainly.com/question/33422249
#SPJ11
An air stream containing 1.6 mol% of SO2 is being scrubbed by pure water in a counter-current packed bed absorption column. The absorption column has dimensions of 1.5 m2 cross-sectional area and 3.5 m packed height. The air stream and liquid stream entering the column at a flowrate of 0.062 kmol s1 and 2.2 kmol s'; respectively. If the outlet mole fraction of SO2 in the gas is 0.004; determine: (1) Mole fraction of SO2 in the liquid outlet stream; [6 MARKS] (ii) Number of transfer unit (Nos) for absorption of SO2; [4 MARKS] (ili) Height of transfer unit (Hoo) in meters. [2 MARKS] Additional information Equilibrium data of SOz: For air stream entering the column, y;* = 0.009; For air stream leaving the column, yz* = 0.0.
The mole fraction of SO2 in the liquid outlet stream is found to be 0.112.
The number of transfer units (Ntu) for the absorption of SO2 is calculated to be 2.81. The height of a transfer unit (Htu) is approximately 1.247 meters.
(i) The mole fraction of SO2 in the liquid outlet stream can be calculated using the equation:
y* = (x* * L) / (V + L)
Where y* is the mole fraction of SO2 in the gas phase (0.004), x* is the mole fraction of SO2 in the liquid phase (what we want to find), L is the liquid flowrate (2.2 kmol/s), and V is the gas flowrate (0.062 kmol/s).
Rearranging the equation, we have:
x* = (y* * (V + L)) / L
Substituting the given values, we get:
x* = (0.004 * (0.062 + 2.2)) / 2.2
x* = 0.112
Therefore, the mole fraction of SO2 in the liquid outlet stream is 0.112.
(ii) The number of transfer units (Ntu) for the absorption of SO2 can be determined using the equation:
Ntu = -log((y2* - y1*) / (y2* - x2*))
Where y1* is the mole fraction of SO2 in the gas phase entering the column (0.009), y2* is the mole fraction of SO2 in the gas phase leaving the column (0.004), and x2* is the mole fraction of SO2 in the liquid phase leaving the column (0.112).
Substituting the given values, we have:
Ntu = -log((0.004 - 0.009) / (0.004 - 0.112))
Ntu = -log(0.5 / -0.108)
Ntu = 2.81
Therefore, the number of transfer units (Ntu) for the absorption of SO2 is 2.81.
(iii) The height of a transfer unit (Htu) can be calculated by dividing the packed height of the absorption column by the number of transfer units (Ntu).
Htu = H / Ntu
Substituting the given packed height (3.5 m) and the calculated Ntu (2.81), we have:
Htu = 3.5 / 2.81
Htu ≈ 1.247 m
Therefore, the height of a transfer unit (Htu) is approximately 1.247 m.
Know more about Mole fraction here:
https://brainly.com/question/30724931
#SPJ11
By what number should 6 2/9 be divided to obtain 4 2/3
Answer:
Step-by-step explanation:ns:
ANS: 4/3.
calculate the vertical reaction
5. Calculate the Vertical reaction of support A. Take E as 8 KN, G as 3 kN, H as 4 kN. also take K as 12 m, Las 3 m, N as 10 m. 5 MARKS H KN H HKN ERN T 16 G F GEN E А B IC ID Nm Nm Nm Nm
The vertical reaction at support A can be calculated using the principle of equilibrium. Considering the given forces, distances, and the geometry of the system, the vertical reaction can be determined as follows:
1. Calculate the vertical reaction at support A using the principle of equilibrium.
2. Convert all the given forces to kilonewtons (kN) if necessary.
3. Apply the summation of vertical forces at support A to find the reaction.
Given forces: E = 8 kN, G = 3 kN, H = 4 kN.Given distances: K = 12 m, L = 3 m, N = 10 m.Vertical reaction at support A is represented by RA.Convert forces to kilonewtons (kN): E = 8 kN, G = 3 kN, H = 4 kN.Apply the summation of vertical forces at support A: RA - 8 kN - 3 kN - 4 kN = 0.Simplify the equation: RA - 15 kN = 0.Solve for RA: RA = 15 kN.The vertical reaction at support A is determined to be 15 kilonewtons (kN). The calculation is based on the principle of equilibrium, which ensures that the sum of all vertical forces acting on the support is equal to zero. By rearranging the equation and solving for the unknown reaction, we obtain the final result of 15 kN.
Learn more about Equilibrium:
https://brainly.com/question/517289
#SPJ11
What cosine function represents an amplitude of 2, a period of 2π, a horizontal shift of π, and a vertical shift of −1? (Multiple choice) Help!!!
The cosine function that represents an amplitude of 2, a period of 2π, a horizontal shift of π, and a vertical shift of −1 is f(x) = 2cos(x - π) - 1.
To find the cosine function that satisfies the given conditions, we can use the general form of the cosine function:
f(x) = A [tex]\times[/tex] cos(B(x - C)) + D
Where A represents the amplitude, B represents the frequency, C represents the horizontal shift, and D represents the vertical shift.
According to the given conditions:
The amplitude is 2, so A = 2.
The period is 2π, which is the standard period for cosine functions, so B = 1.
The horizontal shift is π, so C = π.
The vertical shift is -1, so D = -1.
Plugging these values into the general form, we have:
f(x) = 2 [tex]\times[/tex] cos(1(x - π)) - 1
Simplifying further:
f(x) = 2 [tex]\times[/tex] cos(x - π) - 1
Therefore, the cosine function that represents an amplitude of 2, a period of 2π, a horizontal shift of π, and a vertical shift of -1 is f(x) = 2 [tex]\times[/tex] cos(x - π) - 1.
In multiple-choice format, the correct answer would be:
C. f(x) = 2 [tex]\times[/tex] cos(x - π) - 1
For similar question on amplitude.
https://brainly.com/question/3613222
#SPJ8
Draw the product(s) of each reaction shown below. Be sure to clearly indicate regiochemistry and stereochemistry where appropriate. If a mixture of enantiomers will be formed, draw one stereoisomer and write "+ enantiomer".
However, here is a guide on how to draw products of a reaction properly:Guide in Drawing Products of a ReactionIf you want to draw the products of a reaction, you need to understand the mechanism behind the reaction and the reagents used.
Here are some steps to guide you. Write the balanced equation for the reaction Firstly, you need to write the balanced equation for the reaction you are given. Make sure you use the correct stoichiometry for each reagent used.2. Determine the reagents used and the mechanism of the reaction:Now that you have the balanced equation, determine the reagents used and the mechanism of the reaction.
Identify the functional groups involved:Once you have determined the mechanism of the reaction, you need to identify the functional groups involved in the reaction. This will give you a clue as to the type of reaction that occurred.4. Determine the regiochemistry and stereochemistry of the products:Finally, determine the regiochemistry and stereochemistry of the products. This will give you an idea of the orientation of the reaction products with respect to each other or with respect to the reactants used.
To know more about reaction visit :
https://brainly.com/question/30464598
#SPJ11
Find the mean and standard deviation of the data 2. The following data lists the Major League' s winning batting average for the years 2004 through 2011. Draw a line graph for these data. 3. The depth of a silicon wafer is targeted at 1.015 mm. If properly functioning, the process produces items with mean 1.015 mm and has a standard deviation of ±0.004 mm. A sample of 16 items is measured once each hour. The sample means for the past 12 h are given in the data. From the data, make a mean control chart and determine whether the process is in control.
The mean and standard deviation of the data are
[tex]$\\text{Mean} = \\bar{x} = 3$[/tex]
[tex]$\\text{Standard deviation} = s \\approx 2.16$[/tex]
We are given that;
To find the mean and standard deviation of the data, we need to use the following formulas:
[tex]$\\text{Mean} = \\bar{x} = \\frac{\\sum x}{n}$[/tex]
[tex]$\\text{Standard deviation} = s = \\sqrt{\\frac{\\sum (x - \\bar{x})^2}{n-1}}$[/tex]
where x is a data point, [tex]$\\bar{x}$[/tex]is the mean, n is the number of data points, and s is the standard deviation.
To apply these formulas, we need to have the data in a list form, such as:
[6, 2, 3, 1]
Then, we can follow these steps to find the mean and standard deviation:
- Step 1: Find the sum of the data points: [tex]$\\sum x = 6 + 2 + 3 + 1 = 12$[/tex]
- Step 2: Find the number of data points: n = 4
- Step 3: Find the mean by dividing the sum by the number: [tex]$\\bar{x} = \\frac{12}{4} = 3$[/tex]
- Step 4: Find the deviations of each data point from the mean by subtracting the mean from each data point: [tex]$x - \\bar{x} = [6 - 3, 2 - 3, 3 - 3, 1 - 3] = [3, -1, 0, -2]$[/tex]
- Step 5: Find the squares of each deviation by multiplying each deviation by itself: [tex]$(x - \\bar{x})^2 = [3^2, (-1)^2, 0^2, (-2)^2] = [9, 1, 0, 4]$[/tex]
- Step 6: Find the sum of the squares of the deviations: [tex]$\\sum (x - \\bar{x})^2 = 9 + 1 + 0 + 4 = 14$[/tex]
- Step 7: Find the standard deviation by taking the square root of the quotient of the sum of the squares of the deviations and one less than the number of data points: [tex]$s = \\sqrt{\\frac{14}{4-1}} = \\sqrt{\\frac{14}{3}} \\approx 2.16$[/tex]
Therefore, by mean the answer will be [tex]$\\text{Mean} = \\bar{x} = 3$[/tex]
[tex]$\\text{Standard deviation} = s \\approx 2.16$[/tex]
Learn more about mean and median;
https://brainly.com/question/17060266
#SPJ4