The total energy per unit weight of the water at the specified point is determined by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. According to the principle of conservation of energy, the total energy per unit weight of the fluid in a flow system is constant and is known as Bernoulli's equation.
The following formula can be used to determine the total energy per unit weight of the water at the specified point: T.E./w = P/w + V^2/2g + Z. Where, T.E./w = Total energy per unit weightP/w = Pressure energy per unit weightV = Velocity of the water, g = Acceleration due to gravity Z = Potential energy per unit weight of the water in the pipeline. Thus, putting all the given values into the equation, we get:T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m. Therefore, the total energy per unit weight of water at the given point is 35.692 m. Water flows through pipelines due to the pressure difference between two points, and the velocity of the fluid inside the pipeline is determined by the pressure and other factors, such as the diameter of the pipe, the roughness of the surface of the pipe, and the viscosity of the fluid. Bernoulli's equation is a fundamental principle of fluid mechanics that explains how the energy of a fluid changes as it flows along a pipeline or around a curve. It is the basic principle used to describe the behavior of fluids in motion. Bernoulli's equation can be used to calculate the total energy per unit weight of a fluid at a given point in the pipeline by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. In this problem, water is flowing through a pipeline 600 cm above datum level, with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, and the mass density of water is 1000 kg/m3. We have to calculate the total energy per unit weight of water at this point. Using Bernoulli's equation, we can obtain the following expression: T.E./w = P/w + V^2/2g + Z, Where, T.E./w = Total energy per unit weight P/w = Pressure energy per unit weight, V = Velocity of the water, g = Acceleration due to gravity, Z = Potential energy per unit weight of the water in the pipe line. Putting the given values into the equation, we get: T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m, Thus, the total energy per unit weight of water at the given point is 35.692 m.
In conclusion, the total energy per unit weight of water at a point 600 cm above datum level in a pipeline with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, with a mass density of 1000 kg/m3, is 35.692 m.
Learn more about Bernoulli's equation visit:
brainly.com/question/29865910
#SPJ11
Water flows under the partially opened sluice gate, which is in a rectangular channel. Suppose that yAyAy_A = 8 mm and yByBy_B = 3 mm Find the depth yCyC at the downstream end of the jump.
The depth yC at the downstream end of the jump is 2.66 mm.
The answer is given below, with a word count of 102 words.
Suppose yA = 8 mm and yB = 3 mm. We need to find the depth yC at the downstream end of the jump.The flow is open-channel and has a jump.
As the depth of the jump changes continuously, we need to use the Bernoulli equation between sections 1 and 2.The Bernoulli equation between sections 1 and 2 is given by:
-y1 + V1²/2g + z1 = -y2 + V2²/2g + z2,
where, y is the depth of the water,V is the velocity of the water,g is the acceleration due to gravity,z is the height above an arbitrarily chosen datum line.
Let us take datum line to be at the free water surface at section 2 i.e. z2 = 0. Also, let us assume that velocity at section 1 and section 2 are same, as they are both open to atmosphere. Thus V1 = V2.
Substituting the values and solving for y2, we get:y2 = 2.66 mm.
Therefore, the depth yC at the downstream end of the jump is 2.66 mm.
Thus, the depth yC at the downstream end of the jump in a rectangular channel where yA = 8 mm and yB = 3 mm is 2.66 mm.
To know more about velocity visit:
brainly.com/question/30559316
#SPJ11
Which of the following statements is true for lateral earth pressure calculations?
A) Rankine assumes level backfill and coulomb does not.
B) Rankine assumes friction between soil and wall and coulomb does not .
The statement that is true for lateral earth pressure calculations is "Rankine assumes friction between soil and wall, and Coulomb does not."
What is lateral earth pressure?
Lateral earth pressure is defined as the amount of pressure that soil applies to a wall. The soil behind the wall applies pressure to the wall, which must be taken into account when designing the wall.
The pressure exerted by the soil against the wall is referred to as lateral earth pressure.
Rankine's and Coulomb's theories are two of the most commonly used theories to determine lateral earth pressure.
The true statement for these two theories is given below:
Rankine's theory for lateral earth pressure calculations:
Rankine's theory assumes that the soil behind the wall is dry, has a smooth wall, and does not contain any adhesion between the soil and wall. The lateral earth pressure is distributed in a triangular shape in this situation, and it is known as Rankine's theory of lateral earth pressure. The lateral earth pressure exerted on the wall is:
q = Ks x H
Where, Ks is the lateral earth pressure coefficient
H is the height of soil
Coulomb's theory for lateral earth pressure calculations:
Coulomb's theory assumes that the soil is cohesive and has internal friction and that there is no friction between the wall and the soil. The lateral earth pressure is distributed in a trapezoidal shape in this case. The lateral earth pressure exerted on the wall is given by:
q = Ka x H + Kp
Where, Ka is the active earth pressure coefficient
Kp is the passive earth pressure coefficient
H is the height of soil
To know more about lateral earth pressure visit:
https://brainly.com/question/33302099
#SPJ11
Help me with this math questioned
The graph of the function is attached
The values of the functions are d(0) = 50, d(6) = 95 and d(100) = 800
How to graph the equation of the functionFrom the question, we have the following parameters that can be used in our computation:
d(t) = 7.5t + 50
Also, we have the following from the question
t = 0, t = 6 and t = 100
So, we have
d(0) = 7.5 * 0 + 50
d(0) = 50
d(6) = 7.5 * 6 + 50
d(6) = 95
d(100) = 7.5 * 100 + 50
d(100) = 800
This means that the values are d(0) = 50, d(6) = 95 and d(100) = 800
Next, we plot the graph of the function
The graph is attached
Read more about linear relation at
https://brainly.com/question/30318449
#SPJ1
What should be the quantity of chlorine required to treat a flow of 3MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired?
The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To treat a flow of 3 MLD, the quantity of chlorine required, given a chlorine demand of 12mg/L and a chlorine residual of 2mg/L is 30kg/day.Chlorination is a water treatment process that employs chlorine or chlorine-containing compounds to purify water. The most widely used disinfectant for drinking water, chlorine is relatively inexpensive and capable of killing most pathogens that might be present in the water.
How much chlorine is needed to treat water?
The amount of chlorine needed to treat water is determined by the amount of organic and inorganic matter, ammonia, nitrogen, and other substances present in the water that can react with the chlorine and the volume of water to be treated.
The quantity of chlorine that is required is usually measured in mg/L (milligrams per litre) or ppm (parts per million). For example, a chlorine demand of 12mg/L indicates that 12 milligrams of chlorine are required to disinfect 1 litre of water.
So, to calculate the quantity of chlorine needed to treat a flow of 3 MLD, we need to multiply the flow rate (3 MLD) by the chlorine demand (12mg/L) and then by the number of days in the year (365). This will give us the total amount of chlorine needed per year. Then, we divide this amount by 365 to get the amount of chlorine needed per day.Mathematically,Quantity of chlorine required
= Flow rate x Chlorine demand x 365 / 1000 kg/day
= 3 MLD x 12 mg/L x 365 / 1000 kg/day
= 13,140 kg/day
However, this only gives us the amount of chlorine needed to meet the chlorine demand. If we also want to achieve a chlorine residual of 2 mg/L, we need to add the amount of chlorine required to achieve this residual. The amount of chlorine required to achieve a residual can be determined by conducting a jar test or by using empirical data.For instance, let us say that based on empirical data, we need to add 4 mg/L of chlorine to achieve a residual of 2 mg/L. The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To know more about chlorine visit:
https://brainly.com/question/19460448
#SPJ11
Briefly explain why the Ponchon-Savarit method for calculating the theoretical stages in a binary distillation can be more accurate than McCabeThiele method.
The Ponchon-Savarit method for calculating theoretical stages in a binary distillation can be more accurate than the McCabe-Thiele method because it takes into account the non-ideal behavior of the liquid and vapor phases.
In the Ponchon-Savarit method, the equilibrium curve is represented as a polynomial equation, which allows for a more accurate representation of the separation process. This method also considers the effect of varying reflux ratios on the number of theoretical stages required. By accounting for non-ideal behavior and varying reflux ratios, the Ponchon-Savarit method provides a more accurate estimation of the theoretical stages required for a binary distillation.
On the other hand, the McCabe-Thiele method assumes ideal behavior and constant reflux ratio, which can lead to less accurate results. It represents the equilibrium curve using a straight line, which simplifies the calculations but does not account for non-ideal behavior. Additionally, the McCabe-Thiele method does not consider the effect of varying reflux ratios on the separation process.
In summary, the Ponchon-Savarit method is more accurate than the McCabe-Thiele method in calculating the theoretical stages in a binary distillation because it considers non-ideal behavior and varying reflux ratios.
Know more about Ponchon-Savarit method here:
https://brainly.com/question/33792283
#SPJ11
The foundation of a column is made up of a footing whose dimensions are 3x5m. and 0.5m. high, the bottom level of the foundation is -1.5m. and the level of the natural ground subgrade -0.20m. if the column is 0.4x0.8m. of section determine What will be the fill volume in the construction of the footing and column?
The volume of fill material used in the construction of the foundation and column is equal to the volume of the soil layer at the base of the foundation minus the volume of the footing. Therefore, the volume of fill material used = (19.5 - 7.5) m³ = 12 m³.
Dimensions of footing = 3 x 5 x 0.5 m
Bottom level of foundation = -1.5 m
Level of natural ground subgrade = -0.20 m
Section of column = 0.4 x 0.8 m
The volume of fill material used in the construction of the footing and column has to be determined.
Calculation of volume of fill material used in the construction of footing and column
:Volume of footing = (length x width x height)
= (3 x 5 x 0.5) m³
= 7.5 m³
Volume of soil layer at the base of foundation = (length x width x depth)
= (3 x 5 x 1.3) m³
= 19.5 m³
Volume of fill material used in the construction of the foundation and column = (19.5 - 7.5) m³ = 12 m³
The volume of fill material used in the construction of the foundation and column is 12 m³.
The footing is the base part of the foundation of a column and helps to spread the load over a larger area so that the soil beneath the foundation does not become overstressed or compressed. The dimensions of the footing provided in the question are 3 x 5 x 0.5 m, which gives a volume of 7.5 m³.The bottom level of the foundation is given to be -1.5 m, and the level of the natural ground subgrade is given to be -0.20 m.
Therefore, the height of the soil layer at the base of the foundation = 1.5 - (-0.20) = 1.3 m.
The volume of this soil layer is (length x width x depth) = (3 x 5 x 1.3) m³ = 19.5 m³.
To know more about volume visit:
https://brainly.com/question/28338582
#SPJ11
When nickel-63 is converted to copper-63 A) an electron is captured B) a neutron is released C) an alpha particle is emitted D) an electron is released
The correct answer is A) an electron is captured.
When nickel-63 (Ni-63) is converted to copper-63 (Cu-63), the process involves a nuclear transformation where a neutron in the nickel nucleus is converted into a proton. This conversion is accompanied by the capture of an electron from the electron cloud surrounding the nucleus.
In this process, a neutron in the nickel nucleus is converted to a proton, resulting in a change in atomic number from 28 (nickel) to 29 (copper). Since the number of protons determines the identity of an element, the nucleus is transformed into copper. To maintain charge neutrality, an electron from the electron cloud is captured by the nucleus to balance the increase in positive charge due to the additional proton.
Therefore, the conversion of nickel-63 to copper-63 involves the capture of an electron (option A) to maintain charge balance during the nuclear transformation.
Learn more about electron from the given link:
https://brainly.com/question/12001116
#SPJ11
Calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0. (Ka for HCN is 6.2 x 10-10)
A. 0.0034g
B. 11g
C. 24g
D. 160g
E. 0.15g
The number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
To calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0, we need to consider the dissociation of HCN and the resulting concentration of CN- ions.
The dissociation of HCN can be represented by the equation: HCN ⇌ H+ + CN-
Since we want to achieve a pH of 7.0, we know that the concentration of H+ ions should be equal to 10^(-7) M. Using the equation for the dissociation constant (Ka) of HCN (6.2 x 10^(-10)), we can determine the concentration of CN- ions.
Ka = [H+][CN-]/[HCN]
By substituting the known values into the equation, we can solve for [CN-]. Rearranging the equation, we have:
[Cn-] = (Ka * [HCN])/[H+]
[Cn-] = (6.2 x 10^(-10) * 0.5) / 10^(-7)
[Cn-] = 3.1 x 10^(-10) M
Now, we can calculate the number of moles of CN- ions present in the 1.0 L solution:
moles = concentration * volume
moles = 3.1 x 10^(-10) * 1.0
moles = 3.1 x 10^(-10) mol
Finally, we can calculate the mass of NaCN required using the molar mass of NaCN (49.01 g/mol):
mass = moles * molar mass
mass = 3.1 x 10^(-10) * 49.01
mass ≈ 1.52 x 10^(-8) g
Therefore, the number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
Know more about dissociation here:
https://brainly.com/question/32501023
#SPJ11
QUESTION (2) In your own words, discuss the process of undertaking an LCA on two types (solar and hydropower) of renewable energy system. You should mention the key steps involved (goal and scope definition, inventory analysis, allocation, etc.), as well as guidance on how an LCA report should be interpreted. What would be the expected main sources of carbon emissions for such systems and how could the environmental impact be reduced?
A comprehensive LCA provides valuable insights into the environmental performance of solar and hydropower systems, enabling informed decision-making and the implementation of strategies to mitigate their carbon emissions and environmental impact.
Undertaking a Life Cycle Assessment (LCA) on two types of renewable energy systems, such as solar and hydropower, involves evaluating their environmental impacts throughout their entire life cycle. Here is a discussion of the key steps involved in conducting an LCA and interpreting the LCA report for these systems:
Goal and Scope Definition: The first step is to define the goal and scope of the LCA study. This includes identifying the purpose of the assessment, defining the system boundaries, determining the functional unit (e.g., energy generated), and specifying the life cycle stages to be considered (e.g., raw material extraction, manufacturing, operation, end-of-life).
Inventory Analysis: In this step, data is collected on the inputs (energy, materials, water, etc.) and outputs (emissions, waste, etc.) associated with each life cycle stage of the renewable energy systems. This data is often gathered from various sources, such as literature, industry databases, and specific measurements.
Impact Assessment: The collected inventory data is then analyzed to assess the potential environmental impacts of the systems. Impact categories, such as greenhouse gas emissions, air pollution, water consumption, and land use, are evaluated using impact assessment methods. These methods help quantify and compare the environmental impacts across different categories.
Interpretation: The LCA report should be interpreted with care, considering the specific context and limitations of the study. It is important to understand the boundaries and assumptions made during the assessment. The interpretation should take into account the magnitude and significance of the environmental impacts identified, allowing for informed decision-making and potential improvements.
For solar and hydropower systems, the expected main sources of carbon emissions can vary depending on factors such as the manufacturing processes, material choices, and the energy mix used during construction and operation. Key sources may include the production of solar panels (including energy-intensive manufacturing processes) and the emissions associated with the construction and maintenance of hydropower infrastructure.
To reduce the environmental impact of these systems, several strategies can be considered:
Efficiency Improvements: Enhancing the efficiency of solar panels and hydropower turbines can increase the energy output per unit of input and reduce the overall environmental impact.
Renewable Energy Integration: Using renewable energy sources, such as wind or solar, for manufacturing processes and operation of the systems can minimize reliance on fossil fuel-based energy sources and reduce carbon emissions.
Material Selection: Opting for sustainable and low-carbon materials during the manufacturing of solar panels and hydropower infrastructure can help reduce the embodied carbon and environmental impact.
End-of-Life Management: Implementing proper recycling and disposal methods for decommissioned solar panels and hydropower equipment can minimize waste and promote circular economy principles.
Life Cycle Optimization: Conducting ongoing assessments and optimizations of the systems' life cycles can identify areas for improvement and guide decision-making towards reducing environmental impacts.
To learn more about hydropower
brainly.com/question/22258411
#SPJ11
4a) Solve each equation.
Answer:
Subtract 7 from both sides which gives you 2x=12
x=6
Liquid methanol goes through a change from state 1 (27 °C, 1 bar, 1.4 cm /g) to state 2 (T °C, P bar and V cm²/g). Given the values for T, P and V in Table 1 and also given that the isothermal compressibility is 47 x 10-6 /bar, determine methanol's volume expansivity. Provide any necessary derivation(s) and assumptions in your solution.
The volume expansivity of methanol can be determined using the provided information and the formula:
β = -(1/V)(∂V/∂T)P
To determine the volume expansivity (β) of methanol, we need to use the formula that relates β to the partial derivative of volume (V) with respect to temperature (T) at constant pressure (P). The formula is given as β = -(1/V)(∂V/∂T)P.
Assuming that methanol behaves as an ideal gas, we can use the ideal gas law, PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature. By differentiating this equation, we get (∂V/∂T)P = (nR/P), which simplifies to (∂V/∂T)P = (V/P)β.
Substituting this expression into the volume expansivity formula, we have β = -(1/V)(V/P)β. Simplifying the equation further, we find β = -1/P.
Given that the isothermal compressibility (κ) is 47 x 10^-6 /bar, we can relate it to the volume expansivity using the equation β = κ/P. Therefore, β = (47 x 10^-6 /bar)/P.
By substituting the given values for pressure (P) from Table 1 into the above equation, we can determine the volume expansivity (β) of methanol.
Learn more about Methanol
brainly.com/question/18725375
#SPJ11
Which of the following linear hydrocarbons may have a double bond? A) C_6 H_14 B) C_10 H_20 C) C_5 H_8 D) C_12H_22
The linear hydrocarbon that may have a double bond is option C) C5H8.
To determine which of the given linear hydrocarbons may have a double bond, we need to consider the molecular formula and the number of hydrogen atoms in each molecule.
A) C6H14: This hydrocarbon has 6 carbon atoms and 14 hydrogen atoms. The general formula for an alkane (saturated hydrocarbon) with n carbon atoms is CnH2n+2. By applying this formula, we find that C6H14 corresponds to an alkane.
Since alkanes only have single bonds between carbon atoms, there is no double bond present. Therefore, option A is not the correct answer.
B) C10H20: This hydrocarbon has 10 carbon atoms and 20 hydrogen atoms. Again, applying the general formula for alkanes, we see that C10H20 corresponds to an alkane. Therefore, option B is not the correct answer.
C) C5H8: This hydrocarbon has 5 carbon atoms and 8 hydrogen atoms. The general formula for an alkene (unsaturated hydrocarbon with one double bond) with n carbon atoms is CnH2n. By comparing the molecular formula C5H8 to the formula for alkenes, we see that the ratio matches.
Therefore, option C is a possible linear hydrocarbon that may have a double bond.
D) C12H22: This hydrocarbon has 12 carbon atoms and 22 hydrogen atoms. Applying the general formula for alkanes, we see that C12H22 corresponds to an alkane. Therefore, option D is not the correct answer.
Based on the analysis, the linear hydrocarbon that may have a double bond is C) C5H8.
Learn more about hydrocarbon from the given link
https://brainly.com/question/7509853
#SPJ11
If the lengths AB=4cm, BC=5cm, and CD=9cm, calculate the length AC. Write your answer to 3 significant figures.
To find the length AC, use the Pythagorean Theorem, which states that for a right triangle, the sum of the squares of the legs (the shorter sides) equals the square of the hypotenuse (the longest side). So, the length of AC is 6.40 cm
The legs are AB and BC, while the hypotenuse is AC. Therefore, you can use the Pythagorean Theorem to calculate the length of AC. Then, add CD to the length of AC to obtain the length of AD. To summarize, we have the following steps:
Step 1: Use the Pythagorean Theorem to calculate the length of AC²AB² + BC² = AC²4² + 5² = AC²16 + 25 = AC²41AC² = 41AC = √41 = 6.403124237 (rounded to 3 significant figures)
Step 2: Add CD to the length of AC to find the length of ADAD = AC + CDAD = 6.403124237 + 9 = 15.40312424 (rounded to 3 significant figures). Therefore, the length of AC is 6.40 cm (rounded to 3 significant figures).
For more questions on: Pythagorean Theorem
https://brainly.com/question/343682
#SPJ8
7.8 An approximate equation for the velocity distribution in a pipe with turbulent flow is ye sili 19wans 2016 bus abrowa 101 svin oala vost V = enollsups Vmax To 911 m s(es. nism svi srl sus tarW. where Vmax is the centerline velocity, y is the distance from the wall of the pipe, ro is the radius of the pipe, and n is an exponent that depends on the Reynolds number and varies between 1/6 and 1/8 for most applications. Derive a formula for a as a 100 indigntuan function of n. What is a if n = 1/7?
The correct value of "a" as a function of "n" when n = 1/7.
To derive a formula for "a" as a function of "n," we start with the given equation:V = Vmax * (1 - (y / r)^(1/n))
Rearranging the equation, we isolate the term (y / r)^(1/n):
(y / r)^(1/n) = 1 - (V / Vmax)
To find "a," we raise both sides of the equation to the power of "n":
[(y / r)^(1/n)]^n = (1 - (V / Vmax))^n
Simplifying the left side:
y / r = (1 - (V / Vmax))^n
Finally, multiplying both sides by "r," we obtain the formula for "a":
a = r * (1 - (V / Vmax))^n
Now, if n = 1/7, we substitute this value into the formula:
a = r * (1 - (V / Vmax))^(1/7)
This gives the value of "a" as a function of "n" when n = 1/7.
Learn more about function here:
https://brainly.com/question/28793267
#SPJ8
Fill the blanks in the following statements about HMA construction a) In a paver the___
receives HMA from the conveyor and spreads it out evenly over the width to be
paved. The paver provide compaction between____and___ percent of
of maximum density.
a) In a paver, the screed receives HMA from the conveyor and spreads it out evenly over the width to be paved. The paver provides compaction between 91 and 96 percent of maximum density.
The screed is an essential component of the asphalt paver. It consists of a long, adjustable metal plate located at the rear of the paver. The HMA (Hot Mix Asphalt) is delivered onto the screed through the conveyor system. The screed then spreads the HMA evenly over the width of the pavement.
Compaction is a crucial step in HMA construction to ensure the durability and stability of the pavement. The paver is equipped with compactors, typically in the form of steel wheels or vibrating drums, which compact the HMA during the paving process. The compaction process reduces air voids within the HMA, increasing its density and improving its load-bearing capacity.
The compaction level achieved by the paver typically ranges between 91 and 96 percent of the maximum theoretical density of the HMA. This range is considered optimal for achieving a dense and durable pavement surface. Compaction levels below this range can result in reduced pavement performance, while levels above can lead to cracking or deformation.
In conclusion, the paver's screed plays a vital role in spreading the HMA, while the paver's compactors provide compaction between 91 and 96 percent of maximum density to ensure a high-quality asphalt pavement.
To know more about HMA, visit;
https://brainly.com/question/31951891
#SPJ11
y ′′ +2y′ +y=0,y(0)=2;y(1)=2
Answer: the solution to the given differential equation with the initial conditions y(0) = 2 and y(1) = 2 is:
yy(t) = (2 + 4et)e^(-t)
The given equation is a second-order linear homogeneous ordinary differential equation. We can solve it using various methods, such as the characteristic equation or the method of undetermined coefficients. Let's solve it using the characteristic equation method.
The characteristic equation for the given differential equation is:
r^2 + 2r + 1 = 0
To solve this quadratic equation, we can factor it:
(r + 1)(r + 1) = 0
From this, we see that there is a repeated root of -1. Let's denote this repeated root as r1 = r2 = -1.
The general solution for a second-order linear homogeneous differential equation with repeated roots is given by:
y(t) = (c1 + c2t)e^(-t)
To find the particular solution that satisfies the initial conditions, we differentiate the general solution to find y'(t):
y'(t) = (-c1 - c2t)e^(-t) + (c2)e^(-t) = (-c1 + c2(1 - t))e^(-t)
Using the initial condition y(0) = 2, we substitute t = 0 into the general solution:
y(0) = (c1 + c2(0))e^(-0) = c1 = 2
Now we have c1 = 2. Let's differentiate the general solution again to find y''(t):
y''(t) = (c1 - c2 + c2)e^(-t) = 2e^(-t)
Using the initial condition y'(1) = 2, we substitute t = 1 and y'(t) = 2 into the differentiated general solution:
y'(1) = (-c1 + c2(1 - 1))e^(-1) = 2
(-2 + c2)e^(-1) = 2
c2e^(-1) = 4
c2 = 4e
Therefore, the particular solution for the given initial conditions is:
y(t) = (2 + 4et)e^(-t)
So, the solution to the given differential equation with initial conditions y(0) = 2 and y(1) = 2 is:
y(t) = (2 + 4et)e^(-t)
Learn more about differential equation, :
https://brainly.com/question/28099315
#SPJ11
Show your complete solution. Thank you.
5. If the absolute pressure is 13.99 psia and a gage attached to a tank reads 7.4 in Hg vacuum, find the absolute pressure within the tank.
The absolute pressure within the tank is 25.05 psia.
To find the absolute pressure within the tank, we need to consider the given information. The absolute pressure is given as 13.99 psia, and the gage attached to the tank reads 7.4 in Hg vacuum.
First, let's convert the vacuum reading from inches of mercury (in Hg) to psia. Since the vacuum is measured below atmospheric pressure, we need to subtract the vacuum reading from the atmospheric pressure. The atmospheric pressure is approximately 14.7 psia.
Converting 7.4 in Hg to psia:
Vacuum pressure = Atmospheric pressure - Vacuum reading
Vacuum pressure = 14.7 psia - 7.4 in Hg
To convert in Hg to psia, we use the conversion factor: 1 in Hg = 0.491154 psia.
Vacuum pressure = 14.7 psia - (7.4 in Hg × 0.491154 psia/in Hg)
After performing the calculation:
Vacuum pressure = 14.7 psia - (7.4 × 0.491154) psia
Vacuum pressure ≈ 14.7 psia - 3.6331536 psia
Vacuum pressure ≈ 11.0668464 psia
Finally, to find the absolute pressure within the tank, we add the absolute pressure and the vacuum pressure:
Absolute pressure within the tank = Absolute pressure + Vacuum pressure
Absolute pressure within the tank = 13.99 psia + 11.0668464 psia
Absolute pressure within the tank ≈ 25.0568464 psia
Learn more about Tank
brainly.com/question/32846239
#SPJ11
Use the Laplace transform to solve the following initial value problem: y′′+14y′+98y=δ(t−8)y(0)=0,y′(0)=0 y(t)= (Notation: write u(t−c) for the Heaviside step function uc(t) with step at t=c )
The Laplace transform of the given initial value problem is Y(s) = (e^(-8s)) / (s^2 + 14s + 98), and the inverse Laplace transform of Y(s) will give us the solution y(t) to the initial value problem.
To solve the given initial value problem using Laplace transforms, we will take the Laplace transform of both sides of the differential equation.
First, let's denote the Laplace transform of a function y(t) as Y(s), where s is the complex variable in the Laplace domain.
Taking the Laplace transform of the differential equation y'' + 14y' + 98y = δ(t-8), we get:
s^2Y(s) - sy(0) - y'(0) + 14(sY(s) - y(0)) + 98Y(s) = e^(-8s)
Since y(0) = 0 and y'(0) = 0, the above equation simplifies to:
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
Now, let's substitute the initial conditions into the equation:
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
Factoring out Y(s), we get:
(Y(s))(s^2 + 14s + 98) = e^(-8s)
Dividing both sides by (s^2 + 14s + 98), we have:
Y(s) = (e^(-8s)) / (s^2 + 14s + 98)
Now, we need to take the inverse Laplace transform of Y(s) to obtain the solution y(t). However, the expression (e^(-8s)) / (s^2 + 14s + 98) does not have a simple inverse Laplace transform.
To proceed, we can use partial fraction decomposition or refer to Laplace transform tables to find the inverse transform.
In summary, the Laplace transform of the given initial value problem is Y(s) = (e^(-8s)) / (s^2 + 14s + 98), and the inverse Laplace transform of Y(s) will give us the solution y(t) to the initial value problem.
Learn more about Laplace transform from the given link
https://brainly.com/question/2272409
#SPJ11
Find the volume and surface area of the figure.
Round to the nearest hundredths when
necessary.
Answer:
Volume: 395.84 Surface Area: 929.86
Step-by-step explanation:
Volume: pie*radius*hieght
pie*(14/2)*18
pie*7*18
pie*126
395.84
Surface Area: 2πrh+2πr2
2*pie*7*18+2*pie*7*2
791.6813+87.96459
929.8558
Product inventories have been prepared for two different designs of a high speed widget. The matrices are shown in the following. The data on the left side are about Design 1 , on the right are about Design 2. (1) Based on streamlined LCA (SLCA) analysis of the data (show column score, row score, and final overall score for each design option), select the better product from a DfES viewpoint, (2) What aspects of each design do you need to improve from DfES viewpoint? Support your answer with data and reasons. (3) Illustrate the data in the "Target Plot" chart (one plot for each design option) and submit the completed charts. The blank chart "Streamlined LCA_Pie Chart" is in Blackboard folder "Week 2_July 11-15: Class Learning Materials" Packing=PD, Recycling=RD. Resource extraction=pre-manufacture=PM. Text Table 14.2 and Fig. 14.2, p.196 shows full name of each abbreviation.
1. Based on streamlined LCA (SLCA) analysis of the data, Design 1 is the better product from a DfES viewpoint. The column score, row score, and final overall score for each design option are shown in the table below:Design Option Column Score Row Score Final Overall Score Design 1.984.925.98 Design 2.933.545.09
2. Aspects of each design that need improvement from a DfES viewpoint are:Design 1: Although Design 1 has a better score than Design 2, it still has room for improvement. The resource extraction stage needs improvement, as it has the highest impact of all stages. The production phase also has a relatively high impact, although it is still lower than the resource extraction stage.
Design 2: Although Design 2 has a lower overall score than Design 1, it still has some strengths. Design 2 has a lower impact in the resource extraction stage, but a higher impact in the production stage. The production stage could be improved by reducing energy and water consumption.3. The Target Plot charts for each design option are attached below:Design 1 Target Plot Design 2 Target Plot
To know more about streamlined visit :
https://brainly.com/question/10193549
#SPJ11
Explain in detail the Caseade Control and support your answer with example?
The term "cascade control" refers to a control strategy that involves using the output of one controller as the setpoint for another controller in a series or cascade configuration. This arrangement allows for more precise control and better disturbance rejection in complex systems.
Here is an example to help illustrate the concept: Let's consider a temperature control system for a chemical reactor. The primary controller, known as the "master" controller, regulates the temperature of the reactor by adjusting the heat input.
However, variations in the cooling water flow rate can affect temperature control. To address this, a secondary controller called the "slave" controller, is introduced to control the cooling water flow rate based on the temperature setpoint provided by the master controller.
In this example, the cascade control setup works as follows: the master controller continuously monitors the reactor temperature and adjusts the heat input accordingly. If the temperature deviates from the setpoint, the master controller sends a signal to the slave controller, which then adjusts the cooling water flow rate to counteract the disturbance.
By using cascade control, the system benefits from faster response times and reduced interaction between the two control loops. This arrangement enables more precise temperature control and improves the system's ability to reject disturbances.
In summary, cascade control is a control strategy that involves using the output of one controller as the setpoint for another controller. This approach improves control accuracy and disturbance rejection, as demonstrated by the example of a temperature control system for a chemical reactor.
You can learn more about cascade control at: brainly.com/question/30098314
#SPJ11
What is the maximum tractive effort that can be developed for this rear-wheel drive car: • Weight: 2,750 lb. Wheelbase: 113 inches. Center of gravity: 23.5 inch above the road and 51 inch behind the front axle Use maximum coefficient of adhesion on poor, wet pavement.
The maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf (pound force). Tractive effort is the force applied to the wheels of a vehicle to make them move. It is a measure of how much force is needed to move the vehicle.
The formula for tractive effort is given by:T = W × f where T is the tractive effort, W is the weight of the vehicle, and f is the coefficient of adhesion. For a rear-wheel-drive car, the tractive effort is given by:T = (W × g × µr) / rwhere g is the acceleration due to gravity (32.2 ft/s²), µr is the coefficient of rolling resistance, and r is the effective radius of the drive wheel.The coefficient of adhesion on poor, wet pavement is 0.1. The weight of the car is 2,750 lb. The center of gravity is 23.5 inches above the road and 51 inches behind the front axle.
The wheelbase is 113 inches. The effective radius of the drive wheel is given by:r = sqrt((w² / 4) + h²)where w is the wheelbase (113 inches) and h is the height of the center of gravity above the rear axle (23.5 - 51 = -27.5 inches, since it is behind the front axle).Therefore,r = sqrt((113² / 4) + (-27.5)²)
≈ 61.2 inches
The tractive effort is given by:T = (W × g × µr) / r
T = (2750 × 32.2 × 0.1) / 61.2T
≈ 4719.98 lbf
Therefore, the maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf.
To know more about tractive effort visit:
https://brainly.com/question/30163187
#SPJ11
A steady, incompressible, two-dimensional velocity field is given by V = (u, v) = (0.5 +0.8x) 7+ (1.5-0.8y)] Calculate the material acceleration at the point (X-3 cm, y=5 cm). Just provide final answers. (1)
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
Given the velocity field: V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
To calculate the material acceleration at the point (x = 3 cm,
y = 5 cm) the expression for acceleration is given as:
a = ∂v/∂t + V . ∇V
The equation represents the sum of the acceleration due to change of velocity with time and acceleration due to change in direction of flow. Let's begin with calculating the material acceleration by using the given information.
So, we have:
V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
On substituting the values of x and y in V, we get
V = (u, v)
= [(0.5 + 0.8 × 3) 7 + (1.5 - 0.8 × 5)]
= (6.1, -2.7)
The time derivative of the velocity field is:
∂v/∂t = (∂u/∂t, ∂v/∂t)
= 0 (since it is given steady)
Now, we calculate the gradient of the velocity field as:
∇V = [(∂u/∂x), (∂v/∂y)]
= [0.8, -0.8]
Therefore, the material acceleration is calculated using the equation:
a = ∂v/∂t + V . ∇V
a = 0 + (6.1, -2.7) . [0.8, -0.8]
= (2.88, 4.16) cm/s²
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
To know more about acceleration visit
https://brainly.com/question/16710160
#SPJ11
Help please , 20 points
If the measure of angle A is 23 degrees, the approximate measure of angle B is 67°.
If CA = 6.5 and BD = 5, then AD = 4.15 units.
What is a supplementary angle?In Mathematics and Geometry, a supplementary angle simply refers to two (2) angles or arc whose sum is equal to 180 degrees.
Additionally, the sum of all of the angles on a straight line is always equal to 180 degrees. In this scenario, we can logically deduce that the sum of the given angles are supplementary angles:
m∠ACB + m∠A + m∠B = 180°
m∠B = 180° - (90 + 23)
m∠B = 67°
Since AB is a diameter (angle D is a right angle), we would apply Pythagorean's theorem to find AD as follows;
AB² = AD² + DB²
AD² = AB² - DB²
AD² = 6.5² - 5²
AD = √17.25
AD = 4.15 units.
Read more on supplementary angle here: brainly.com/question/13250148
#SPJ1
An air-water vapor mixture has a dry bulb temperature of 35°C and an absolute humidity of 0.025kg water/kg dry air at 1std atm. Find i) Percentage humidity ii) Adiabatic Saturation temperature iii) Saturation humidity at 35°C. iv) Molal absolute humidity v) Partial pressure of water vapor in the sample vi) Dew point vii) Humid volume viii) Humid heat ix) Enthalpy
The percentage humidity is 51.5%. The adiabatic saturation temperature is 45.5°C. Saturation humidity at 35°C is 0.0485 kg water/kg dry air. The partial pressure of water vapor in the sample is 0.025 atm.
Given that, Dry bulb temperature (Tdb) = 35°C and Absolute humidity (ω) = 0.025 kg water/kg dry air at 1 std atm.
Solution: i) Percentage humidity
Relative humidity (RH) = (Absolute humidity/Saturation humidity) x 100RH
= (0.025/0.0485) x 100RH
= 51.5%
Therefore, the percentage humidity is 51.5%.
ii) Adiabatic saturation temperature
Adiabatic saturation temperature is the temperature attained by the wet bulb thermometer when it is surrounded by the air-water vapor mixture in such a manner that it is no longer cooling. It is the saturation temperature corresponding to the humidity ratio of the moist air. Adabatic saturation temperature is given by
Tsat = 2222/(35.85/(243.04+35)-1)
Tsat = 45.5°C
Therefore, the adiabatic saturation temperature is 45.5°C.
iii) Saturation humidity at 35°C.
The saturation humidity is defined as the maximum amount of water vapor that can be held in the air at a given temperature. It is a measure of the water content in the air at saturation or when the air is holding the maximum amount of moisture possible at a given temperature.
Saturation humidity at 35°C is 0.0485 kg water/kg dry air
iv) Molal absolute humidity
Molal absolute humidity is defined as the number of kilograms of water vapor in 1 kg of dry air, divided by the mass of 1 kg of water.
Molal absolute humidity = (Absolute humidity / (28.97 + 18.015×ω))×1000
Molal absolute humidity = (0.025 / (28.97 + 18.015×0.025))×1000
Molal absolute humidity = 0.710
Therefore, the molal absolute humidity is 0.710 kg/kmol.
v) Partial pressure of water vapor in the sample
Partial pressure of water vapor in the sample is given by
p = ω × P
p = 0.025 × 1 std atm = 0.025 atm
Therefore, the partial pressure of water vapor in the sample is 0.025 atm.
vi) Dew point
Dew point is defined as the temperature at which air becomes saturated with water vapor when cooled at a constant pressure. At this point, the air cannot hold any more moisture in the gaseous form, and some of the water vapor must condense to form liquid water. Dew point can be determined using the following equation:
tdp = (243.04 × (ln(RH/100) + (17.625 × Tdb) / (243.04 + Tdb - 17.625 × Tdb))) / (17.625 - ln(RH/100) - (17.625 × Tdb) / (243.04 + Tdb - 17.625 × Tdb))
tdp = (243.04 × (ln(51.5/100) + (17.625 × 35) / (243.04 + 35 - 17.625 × 35))) / (17.625 - ln(51.5/100) - (17.625 × 35) / (243.04 + 35 - 17.625 × 35))
tdp = 22.4°C
Therefore, the dew point is 22.4°C.
vii) Humid volume
The humid volume is the volume of air occupied by unit mass of dry air and unit mass of water vapor. It is defined as the volume of the mixture of dry air and water vapor per unit mass of dry air.
Vh = (R × (Tdb + 273.15) × (1 + 1.6078×ω)) / (P)
where R is the specific gas constant of air, Tdb is the dry bulb temperature, and P is the atmospheric pressure at the measurement location.
Vh = (0.287 × (35+273.15) × (1+1.6078×0.025)) / (1) = 0.920 m3/kg
Therefore, the humid volume is 0.920 m3/kg.
viii) Humid heat
Humid heat is the amount of heat required to raise the temperature of unit mass of the moist air by one degree at constant moisture content.
q = 1.006 × Tdb + (ω × (2501 + 1.86 × Tdb))
q = 1.006 × 35 + (0.025 × (2501 + 1.86 × 35))
q = 57.1 kJ/kg
Therefore, the humid heat is 57.1 kJ/kg.
ix) Enthalpy
The enthalpy of moist air is defined as the amount of energy required to raise the temperature of the mixture of dry air and water vapor from the reference temperature to the actual temperature at a constant pressure. The reference temperature is typically 0°C, and the enthalpy of moist air at this temperature is zero.
The enthalpy can be calculated as follows:
H = 1.006 × Tdb + (ω × (2501 + 1.86 × Tdb)) + (1.86 × Tdb × ω)
H = 1.006 × 35 + (0.025 × (2501 + 1.86 × 35)) + (1.86 × 35 × 0.025)
H = 67.88 kJ/kg
Therefore, the enthalpy is 67.88 kJ/kg.
Learn more about humidity visit:
brainly.com/question/30672810
#SPJ11
6-10 Let m, n E Z. Prove by contraposition: If m+ n ≥ 19, then m≥ 10 or n ≥ 10.
By contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To prove the statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" by contraposition, we assume the negation of the conclusion and show that it implies the negation of the original statement. The negation of the conclusion "m ≥ 10 or n ≥ 10" is "m < 10 and n < 10." The negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" is "It is not the case that if m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Let's proceed with the proof:
Assume m < 10 and n < 10. We want to show that if m + n ≥ 19, then m ≥ 10 or n ≥ 10 is false.
Since m < 10, we know that the maximum value m can take is 9. Similarly, since n < 10, the maximum value n can take is 9 as well.
If both m and n are at their maximum value of 9, the sum m + n would be 9 + 9 = 18, which is less than 19. Therefore, if m and n are both less than 10, their sum can never be greater than or equal to 19.
Hence, the negation of the conclusion "m < 10 and n < 10" implies the negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Therefore, by contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To know more value click-
http://brainly.com/question/843074
#SPJ11
Explain how waste disposal by landfill emits anthropogenic GHG and formulate the calculation for the CO2-e emission factor of landfill disposal of municipal solid waste (MSW).
The factor 28 is used to account for the higher global warming potential (GWP) of methane than CO2.
Landfills are large pits or sites where waste is dumped into a hole in the ground and buried. However, landfill sites have become one of the significant sources of anthropogenic greenhouse gas (GHG) emissions. This is due to the anaerobic decomposition of biodegradable waste that releases GHG, especially methane (CH4) and carbon dioxide (CO2). This process is known as Landfill Gas (LFG) emissions.
The quantity of GHG that is released into the atmosphere is determined by the amount of waste disposed of and the length of time it takes for the waste to decompose. The LFG can be captured and utilized, and this can help reduce the GHG emissions from landfills. The capture of LFG also has an environmental benefit in terms of reducing the odors and pests that are associated with landfills.
Calculation for the CO2-e emission factor of landfill disposal of municipal solid waste (MSW)
The emission factor for landfill disposal of municipal solid waste (MSW) is the rate of GHG emissions per unit of waste disposed of in the landfill. It is usually measured in kilograms of CO2 equivalent (CO2-e) per metric ton of waste disposed of.
The calculation of the CO2-e emission factor for landfill disposal of MSW is given as:
E = (CH4 × 28) + (CO2 × 1)
Where E = CO2-e emission factor
CH4 = Methane emissions
CO2 = Carbon dioxide emissions
The factor 28 is used to account for the higher global warming potential (GWP) of methane than CO2.
The CO2-e emission factor for landfill disposal of MSW is about 0.6 to 1.1 tons of CO2-e per metric ton of waste disposed of. This implies that for every metric ton of waste that is disposed of in a landfill, about 0.6 to 1.1 tons of CO2-e are emitted into the atmosphere.
To know more about methane, visit:
https://brainly.com/question/12645626
#SPJ11
Concrete derives its strength by the hydration of cement particles, the hydration of cement is not a momentary action but a process continuing for long time. Curing is the process of controlling the rate and extent of moisture loss from concrete during cement hydration. In details write about the curing of the concrete.
Curing is a process that involves controlling the rate and extent of moisture loss during cement hydration. It is essential for the development of strength and durability in concrete structures. By maintaining the right moisture content, temperature, and protection against rapid drying, curing allows the concrete to reach its full potential.
The curing of concrete is a crucial process that helps control the rate and extent of moisture loss during cement hydration. This process is important because it ensures that the concrete gains strength and durability over time. The process follows:
1. Immediately after pouring the concrete, it is essential to protect it from drying out too quickly. This can be done by covering it with a plastic sheet or applying a curing compound. By preventing rapid moisture loss, the curing process allows the concrete to hydrate properly and develop its strength.
2. The duration of the curing process is typically around 7 to 28 days, depending on the type of cement used and the desired strength of the concrete. During this time, it is important to keep the concrete moist to support the ongoing hydration process.
3. One common method of curing is to continuously wet the concrete surface by sprinkling it with water or by using moist burlap or mats. This helps maintain the required moisture content for proper hydration.
4. Another method of curing is through the use of curing compounds. These compounds are liquid coatings that are applied to the concrete surface. They form a barrier that prevents moisture from evaporating, thus promoting the proper curing of the concrete.
5. Curing can also be aided by controlling the temperature of the concrete. High temperatures can accelerate the hydration process but can also lead to excessive moisture loss. On the other hand, low temperatures can slow down hydration. Therefore, maintaining an optimal temperature range is important for effective curing.
6. It's worth noting that proper curing is crucial for achieving the desired strength, durability, and resistance to cracking in concrete structures. Insufficient curing can lead to weakened concrete and an increased risk of cracking.
To know more about cement hydration, refer to the link below:
https://brainly.com/question/17275699#
#SPJ11
Solve the exponential equation using the method of relating the bases by first rewriting the equation in the form e^u=e^v. ex^2=(e^−x)⋅e^20
X=
(Simplify your answer.)
The solutions to the exponential equation are x = -5 and x = 4.
To solve the exponential equation using the method of relating the bases, we can rewrite the equation in the form
[tex]e^u = e^v,[/tex] where u and v are expressions involving x.
Given equation: [tex]ex^2 = (e^−x)⋅e^20[/tex]
First, let's rewrite the right side of the equation using the properties of exponents:
[tex]ex^2 = e^(20 - x)[/tex]
Now we can relate the bases by setting the exponents equal to each other:
[tex]x^2 = 20 - x[/tex]
To simplify further, let's bring all the terms to one side of the equation:
[tex]x^2 + x - 20 = 0[/tex]
This is now a quadratic equation. We can solve it by factoring or using the quadratic formula. Let's factor it:
(x + 5)(x - 4) = 0
Setting each factor equal to zero gives us two possible solutions:
x + 5 = 0 or x - 4 = 0
Solving each equation:
x = -5 or x = 4
Learn more about exponential equation:
https://brainly.com/question/11832081
#SPJ11
7.00 moles of N2 molecule contains how many N atoms?
a) 8.44 X 10_26 atom
b)4.00 X 10_24 atom
c) 8.44 X 10_24 atom d) 2.44 X 10_24 atom
One mole of nitrogen gas (N2) contains 2 moles of nitrogen atoms. Therefore, if we have 7 moles of N2 molecules, we have 7 x 2 = 14 moles of nitrogen atoms.
Since one mole of any element contains 6.022 x 10^23 atoms, 14 moles will contain:
14 x 6.022 x 10^23=8.44 x 10^24N atoms.
Therefore, the appropriate is option C) 8.44 x 10^24 atom.
For this question, we use the mole concept of Avogadro's number. One mole of any substance contains 6.022 x 10^23 atoms, molecules or particles. Hence, if we want to find the number of atoms of nitrogen in 7 moles of nitrogen gas, we must first calculate the number of moles of nitrogen atoms present in it.
To find the number of moles of nitrogen atoms present in 7 moles of N2 molecules, we will use the stoichiometric coefficient.
The stoichiometric coefficient of nitrogen in N2 is 2. Therefore, one mole of nitrogen gas contains 2 moles of nitrogen atoms. As such, we can determine that 7 moles of N2 molecules contain 7 x 2 = 14 moles of nitrogen atoms.
Now that we know the number of moles of nitrogen atoms present, we can calculate the number of atoms present in 14 moles of nitrogen atoms.
By using Avogadro's number, we know that 1 mole of nitrogen atoms contains 6.022 x 10^23 atoms of nitrogen.
Therefore, 14 moles of nitrogen atoms will contain:
[tex]14 x 6.022 x 10^23 = 8.44 x 10^24 N atoms.[/tex]
So option C) [tex]8.44 x 10^24 atom.[/tex]
Thus, 7.00 moles of N2 molecule contains 8.44 X 10^24 N atoms.
To know more about stoichiometric coefficient :
brainly.com/question/32088573
#SPJ11